Some arches have virtually mapped kernel stacks, or will soon have.
tcp_md5_hash_header() uses an automatic variable to copy tcp header
before mangling th->check and calling crypto function, which might
be problematic on such arches.
David says that using percpu storage is also problematic on non SMP
builds.
Just use kmalloc() to allocate scratch areas.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes wrong-interface signaling on 32-bit platforms for entries
created when jiffies > 2^31 + MFC_ASSERT_THRESH.
Signed-off-by: Tom Goff <thomas.goff@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This works in exactly the same way as the CIPSO label cache.
The idea is to allow the lsm to cache the result of a secattr
lookup so that it doesn't need to perform the lookup for
every skbuff.
It introduces two sysctl controls:
calipso_cache_enable - enables/disables the cache.
calipso_cache_bucket_size - sets the size of a cache bucket.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Lengths, checksum and the DOI are checked. Checking of the
level and categories are left for the socket layer.
CRC validation is performed in the calipso module to avoid
unconditionally linking crc_ccitt() into ipv6.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
In some cases, the lsm needs to add the label to the skbuff directly.
A NF_INET_LOCAL_OUT IPv6 hook is added to selinux to match the IPv4
behaviour. This allows selinux to label the skbuffs that it requires.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Request sockets need to have a label that takes into account the
incoming connection as well as their parent's label. This is used
for the outgoing SYN-ACK and for their child full-socket.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
If set, these will take precedence over the parent's options during
both sending and child creation. If they're not set, the parent's
options (if any) will be used.
This is to allow the security_inet_conn_request() hook to modify the
IPv6 options in just the same way that it already may do for IPv4.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
CALIPSO is a hop-by-hop IPv6 option. A lot of this patch is based on
the equivalent CISPO code. The main difference is due to manipulating
the options in the hop-by-hop header.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
The functionality is equivalent to ipv6_renew_options() except
that the newopt pointer is in kernel, not user, memory
The kernel memory implementation will be used by the CALIPSO network
labelling engine, which needs to be able to set IPv6 hop-by-hop
options.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Remove a specified DOI through the NLBL_CALIPSO_C_REMOVE command.
It requires the attribute:
NLBL_CALIPSO_A_DOI.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Enumerate the DOI list through the NLBL_CALIPSO_C_LISTALL command.
It takes no attributes.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Query a specified DOI through the NLBL_CALIPSO_C_LIST command.
It requires the attribute:
NLBL_CALIPSO_A_DOI.
The reply will contain:
NLBL_CALIPSO_A_MTYPE
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
CALIPSO is a packet labelling protocol for IPv6 which is very similar
to CIPSO. It is specified in RFC 5570. Much of the code is based on
the current CIPSO code.
This adds support for adding passthrough-type CALIPSO DOIs through the
NLBL_CALIPSO_C_ADD command. It requires attributes:
NLBL_CALIPSO_A_TYPE which must be CALIPSO_MAP_PASS.
NLBL_CALIPSO_A_DOI.
In passthrough mode the CALIPSO engine will map MLS secattr levels
and categories directly to the packet label.
At this stage, the major difference between this and the CIPSO
code is that IPv6 may be compiled as a module. To allow for
this the CALIPSO functions are registered at module init time.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
with the commit 8c14586fc3 ("net: ipv6: Use passed in table for
nexthop lookups"), net hop lookup is first performed on route creation
in the passed-in table.
However device match is not enforced in table lookup, so the found
route can be later discarded due to egress device mismatch and no
global lookup will be performed.
This cause the following to fail:
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip route add 2001:db8:8086::/48 dev dummy1 metric 20
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy1 metric 20
ip route add 2001:db8:8086::/48 dev dummy2 metric 21
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy2 metric 21
RTNETLINK answers: No route to host
This change fixes the issue enforcing device lookup in
ip6_nh_lookup_table()
v1->v2: updated commit message title
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Reported-and-tested-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving an ICMPv4 message containing extensions as
defined in RFC 4884, and translating it to ICMPv6 at SIT
or GRE tunnel, we need some extra manipulation in order
to properly forward the extensions.
This patch only takes care of Time Exceeded messages as they
are the ones that typically carry information from various
routers in a fabric during a traceroute session.
It also avoids complex skb logic if the data_len is not
a multiple of 8.
RFC states :
The "original datagram" field MUST contain at least 128 octets.
If the original datagram did not contain 128 octets, the
"original datagram" field MUST be zero padded to 128 octets.
In practice routers use 128 bytes of original datagram, not more.
Initial translation was added in commit ca15a078bd
("sit: generate icmpv6 error when receiving icmpv4 error")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For better traceroute/mtr support for SIT and GRE tunnels,
we translate IPV4 ICMP ICMP_TIME_EXCEEDED to ICMPV6_TIME_EXCEED
We also have to translate the IPv4 source IP address of ICMP
message to IPv6 v4mapped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to use this helper from GRE as well, so this is
the time to move it in net/ipv6/icmp.c
Also add a @nhs parameter, since SIT and GRE have different
values for the header(s) to skip.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIT or GRE tunnels might want to translate an IPV4 address
into a v4mapped one when translating ICMP to ICMPv6.
This patch adds the parameter to icmp6_send() but
does not change icmpv6_send() signature.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 version of 3f2fb9a834 ("net: l3mdev: address selection should only
consider devices in L3 domain") and the follow up commit, a17b693cdd876
("net: l3mdev: prefer VRF master for source address selection").
That is, if outbound device is given then the address preference order
is an address from that device, an address from the master device if it
is enslaved, and then an address from a device in the same L3 domain.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 source address selection needs to consider the real egress route.
Similar to IPv4 implement a get_saddr6 method which is called if
source address has not been set. The get_saddr6 method does a full
lookup which means pulling a route from the VRF FIB table and properly
considering linklocal/multicast destination addresses. Lookup failures
(eg., unreachable) then cause the source address selection to fail
which gets propagated back to the caller.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VRF driver needs access to ip6_route_get_saddr code. Since it does
little beyond ipv6_dev_get_saddr and ipv6_dev_get_saddr is already
exported for modules move ip6_route_get_saddr to the header as an
inline.
Code move only; no functional change.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern C standards expect the '__inline__' keyword to come before the return
type in a declaration, and we get a couple of warnings for this with "make W=1"
in the xfrm{4,6}_policy.c files:
net/ipv6/xfrm6_policy.c:369:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static int inline xfrm6_net_sysctl_init(struct net *net)
net/ipv6/xfrm6_policy.c:374:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static void inline xfrm6_net_sysctl_exit(struct net *net)
net/ipv4/xfrm4_policy.c:339:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static int inline xfrm4_net_sysctl_init(struct net *net)
net/ipv4/xfrm4_policy.c:344:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static void inline xfrm4_net_sysctl_exit(struct net *net)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 32b8a8e59c ("sit: add IPv4 over IPv4 support")
ipip6_err() may be called for packets whose IP protocol is
IPPROTO_IPIP as well as those whose IP protocol is IPPROTO_IPV6.
In the case of IPPROTO_IPIP packets the correct protocol value is not
passed to ipv4_update_pmtu() or ipv4_redirect().
This patch resolves this problem by using the IP protocol of the packet
rather than a hard-coded value. This appears to be consistent
with the usage of the protocol of a packet by icmp_socket_deliver()
the caller of ipip6_err().
I was able to exercise the redirect case by using a setup where an ICMP
redirect was received for the destination of the encapsulated packet.
However, it appears that although incorrect the protocol field is not used
in this case and thus no problem manifests. On inspection it does not
appear that a problem will manifest in the fragmentation needed/update pmtu
case either.
In short I believe this is a cosmetic fix. None the less, the use of
IPPROTO_IPV6 seems wrong and confusing.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) gre_parse_header() can be called from gre_err()
At this point transport header points to ICMP header, not the inner
header.
2) We can not really change transport header as ipgre_err() will later
assume transport header still points to ICMP header (using icmp_hdr())
3) pskb_may_pull() logic in gre_parse_header() really works
if we are interested at zone pointed by skb->data
4) As Jiri explained in commit b7f8fe251e ("gre: do not pull header in
ICMP error processing") we should not pull headers in error handler.
So this fix :
A) changes gre_parse_header() to use skb->data instead of
skb_transport_header()
B) Adds a nhs parameter to gre_parse_header() so that we can skip the
not pulled IP header from error path.
This offset is 0 for normal receive path.
C) remove obsolete IPV6 includes
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The algorithm for checksum neutral mapping is incorrect. This problem
was being hidden since we were previously always performing checksum
offload on the translated addresses and only with IPv6 HW csum.
Enabling an ILA router shows the issue.
Corrected algorithm:
old_loc is the original locator in the packet, new_loc is the value
to overwrite with and is found in the lookup table. old_flag is
the old flag value (zero of CSUM_NEUTRAL_FLAG) and new_flag is
then (old_flag ^ CSUM_NEUTRAL_FLAG) & CSUM_NEUTRAL_FLAG.
Need SUM(new_id + new_flag + diff) == SUM(old_id + old_flag) for
checksum neutral translation.
Solving for diff gives:
diff = (old_id - new_id) + (old_flag - new_flag)
compute_csum_diff8(new_id, old_id) gives old_id - new_id
If old_flag is set
old_flag - new_flag = old_flag = CSUM_NEUTRAL_FLAG
Else
old_flag - new_flag = -new_flag = ~CSUM_NEUTRAL_FLAG
Tested:
- Implemented a user space program that creates random addresses
and random locators to overwrite. Compares the checksum over
the address before and after translation (must always be equal)
- Enabled ILA router and showed proper operation.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports some neighbour discovery functions which can be used
by 6lowpan neighbour discovery ops functionality then.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces neighbour discovery ops callback structure. The
idea is to separate the handling for 6LoWPAN into the 6lowpan module.
These callback offers 6lowpan different handling, such as 802.15.4 short
address handling or RFC6775 (Neighbor Discovery Optimization for IPv6
over 6LoWPANs).
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the functionality to add a RA PIO prefix generated
address in an own function. This move prepares to add a hook for
adding a second address for a second link-layer address. E.g. short
address for 802.15.4 6LoWPAN.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds __ndisc_fill_addr_option as low-level function for
ndisc_fill_addr_option which doesn't depend on net_device parameter.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the autoconfiguration if a valid 802.15.4 short address
is available for 802.15.4 6LoWPAN interfaces.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 multicast and link-local addresses require special handling by the
VRF driver:
1. Rather than using the VRF device index and full FIB lookups,
packets to/from these addresses should use direct FIB lookups based on
the VRF device table.
2. fail sends/receives on a VRF device to/from a multicast address
(e.g, make ping6 ff02::1%<vrf> fail)
3. move the setting of the flow oif to the first dst lookup and revert
the change in icmpv6_echo_reply made in ca254490c8 ("net: Add VRF
support to IPv6 stack"). Linklocal/mcast addresses require use of the
skb->dev.
With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses work (icmp, tcp, and udp)
e.g.,
1. packets into VM with VRF config:
ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
ping6 -c3 ff02::1%br1
ssh -6 fe80::e0:f9ff:fe1c:b974%br1
2. packets going out a VRF enslaved device:
ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
ping6 -c3 ff02::1%eth1
ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L3 master devices are virtual devices similar to the loopback
device. Link local and multicast routes for these devices do
not make sense. The ipv6 addrconf code already skips adding a
linklocal address; do the same for the mcast route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a corner case in which udp packets belonging to a same
flow are hashed to different socket when hslot->count changes from 10
to 11:
1) When hslot->count <= 10, __udp_lib_lookup() searches udp_table->hash,
and always passes 'daddr' to udp_ehashfn().
2) When hslot->count > 10, __udp_lib_lookup() searches udp_table->hash2,
but may pass 'INADDR_ANY' to udp_ehashfn() if the sockets are bound to
INADDR_ANY instead of some specific addr.
That means when hslot->count changes from 10 to 11, the hash calculated by
udp_ehashfn() is also changed, and the udp packets belonging to a same
flow will be hashed to different socket.
This is easily reproduced:
1) Create 10 udp sockets and bind all of them to 0.0.0.0:40000.
2) From the same host send udp packets to 127.0.0.1:40000, record the
socket index which receives the packets.
3) Create 1 more udp socket and bind it to 0.0.0.0:44096. The number 44096
is 40000 + UDP_HASH_SIZE(4096), this makes the new socket put into the
same hslot as the aformentioned 10 sockets, and makes the hslot->count
change from 10 to 11.
4) From the same host send udp packets to 127.0.0.1:40000, and the socket
index which receives the packets will be different from the one received
in step 2.
This should not happen as the socket bound to 0.0.0.0:44096 should not
change the behavior of the sockets bound to 0.0.0.0:40000.
It's the same case for IPv6, and this patch also fixes that.
Signed-off-by: Su, Xuemin <suxm@chinanetcenter.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Tom Herbert <tom@herbertland.com>
Fixes: 4068579e1e ("net: Implmement RFC 6936 (zero RX csums for UDP/IPv6")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Fixes: 1d13a96c74 ("ipv6: tcp: fix flowlabel value in ACK messages send from TIME_WAIT")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 ping socket error handler doesn't correctly convert the new 32 bit
mtu to host endianness before using.
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 6d0bfe2261 ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In IPv6 the ToS values are part of the flowlabel in flowi6 and get
extracted during fib rule lookup, but we forgot to correctly initialize
the flowlabel before the routing lookup.
Reported-by: <liam.mcbirnie@boeing.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Kellermann reported a kernel crash with 4.5.0 when IPv6 is
disabled at boot using the kernel option ipv6.disable=1. Using
current net-next with the boot option:
$ ip link add red type vrf table 1001
Generates:
[12210.919584] BUG: unable to handle kernel NULL pointer dereference at 0000000000000748
[12210.921341] IP: [<ffffffff814b30e3>] fib6_get_table+0x2c/0x5a
[12210.922537] PGD b79e3067 PUD bb32b067 PMD 0
[12210.923479] Oops: 0000 [#1] SMP
[12210.924001] Modules linked in: ipvlan 8021q garp mrp stp llc
[12210.925130] CPU: 3 PID: 1177 Comm: ip Not tainted 4.7.0-rc1+ #235
[12210.926168] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[12210.928065] task: ffff8800b9ac4640 ti: ffff8800bacac000 task.ti: ffff8800bacac000
[12210.929328] RIP: 0010:[<ffffffff814b30e3>] [<ffffffff814b30e3>] fib6_get_table+0x2c/0x5a
[12210.930697] RSP: 0018:ffff8800bacaf888 EFLAGS: 00010202
[12210.931563] RAX: 0000000000000748 RBX: ffffffff81a9e280 RCX: ffff8800b9ac4e28
[12210.932688] RDX: 00000000000000e9 RSI: 0000000000000002 RDI: 0000000000000286
[12210.933820] RBP: ffff8800bacaf898 R08: ffff8800b9ac4df0 R09: 000000000052001b
[12210.934941] R10: 00000000657c0000 R11: 000000000000c649 R12: 00000000000003e9
[12210.936032] R13: 00000000000003e9 R14: ffff8800bace7800 R15: ffff8800bb3ec000
[12210.937103] FS: 00007faa1766c700(0000) GS:ffff88013ac00000(0000) knlGS:0000000000000000
[12210.938321] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[12210.939166] CR2: 0000000000000748 CR3: 00000000b79d6000 CR4: 00000000000406e0
[12210.940278] Stack:
[12210.940603] ffff8800bb3ec000 ffffffff81a9e280 ffff8800bacaf8c8 ffffffff814b3135
[12210.941818] ffff8800bb3ec000 ffffffff81a9e280 ffffffff81a9e280 ffff8800bace7800
[12210.943040] ffff8800bacaf8f0 ffffffff81397c88 ffff8800bb3ec000 ffffffff81a9e280
[12210.944288] Call Trace:
[12210.944688] [<ffffffff814b3135>] fib6_new_table+0x24/0x8a
[12210.945516] [<ffffffff81397c88>] vrf_dev_init+0xd4/0x162
[12210.946328] [<ffffffff814091e1>] register_netdevice+0x100/0x396
[12210.947209] [<ffffffff8139823d>] vrf_newlink+0x40/0xb3
[12210.948001] [<ffffffff814187f0>] rtnl_newlink+0x5d3/0x6d5
...
The problem above is due to the fact that the fib hash table is not
allocated when IPv6 is disabled at boot.
As for the VRF driver it should not do any IPv6 initializations if IPv6
is disabled, so it needs to know if IPv6 is disabled at boot. The disable
parameter is private to the IPv6 module, so provide an accessor for
modules to determine if IPv6 was disabled at boot time.
Fixes: 35402e3136 ("net: Add IPv6 support to VRF device")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipip6_tunnel_xmit() is called immediately after checking that
skb->protocol is htons(ETH_P_IPV6) so there is no need
to check it a second time.
Found by inspection.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6 GRE tap device should not be forced to down state to change
the mac address and should allow live address change for tap device
similar to ipv4 gre.
Signed-off-by: Shweta Choudaha <schoudah@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ip6 GRE tap device should not be forced to down state to change
the mac address and should allow live address change for tap device
similar to ipv4 gre.
Signed-off-by: Shweta Choudaha <schoudah@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, VRFs require 1 oif and 1 iif rule per address family per
VRF. As the number of VRF devices increases it brings scalability
issues with the increasing rule list. All of the VRF rules have the
same format with the exception of the specific table id to direct the
lookup. Since the table id is available from the oif or iif in the
loopup, the VRF rules can be consolidated to a single rule that pulls
the table from the VRF device.
This patch introduces a new rule attribute l3mdev. The l3mdev rule
means the table id used for the lookup is pulled from the L3 master
device (e.g., VRF) rather than being statically defined. With the
l3mdev rule all of the basic VRF FIB rules are reduced to 1 l3mdev
rule per address family (IPv4 and IPv6).
If an admin wishes to insert higher priority rules for specific VRFs
those rules will co-exist with the l3mdev rule. This capability means
current VRF scripts will co-exist with this new simpler implementation.
Currently, the rules list for both ipv4 and ipv6 look like this:
$ ip ru ls
1000: from all oif vrf1 lookup 1001
1000: from all iif vrf1 lookup 1001
1000: from all oif vrf2 lookup 1002
1000: from all iif vrf2 lookup 1002
1000: from all oif vrf3 lookup 1003
1000: from all iif vrf3 lookup 1003
1000: from all oif vrf4 lookup 1004
1000: from all iif vrf4 lookup 1004
1000: from all oif vrf5 lookup 1005
1000: from all iif vrf5 lookup 1005
1000: from all oif vrf6 lookup 1006
1000: from all iif vrf6 lookup 1006
1000: from all oif vrf7 lookup 1007
1000: from all iif vrf7 lookup 1007
1000: from all oif vrf8 lookup 1008
1000: from all iif vrf8 lookup 1008
...
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
With the l3mdev rule the list is just the following regardless of the
number of VRFs:
$ ip ru ls
1000: from all lookup [l3mdev table]
32765: from all lookup local
32766: from all lookup main
32767: from all lookup default
(Note: the above pretty print of the rule is based on an iproute2
prototype. Actual verbage may change)
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At present we perform an xfrm_lookup() for each UDPv6 message we
send. The lookup involves querying the flow cache (flow_cache_lookup)
and, in case of a cache miss, creating an XFRM bundle.
If we miss the flow cache, we can end up creating a new bundle and
deriving the path MTU (xfrm_init_pmtu) from on an already transformed
dst_entry, which we pass from the socket cache (sk->sk_dst_cache) down
to xfrm_lookup(). This can happen only if we're caching the dst_entry
in the socket, that is when we're using a connected UDP socket.
To put it another way, the path MTU shrinks each time we miss the flow
cache, which later on leads to incorrectly fragmented payload. It can
be observed with ESPv6 in transport mode:
1) Set up a transformation and lower the MTU to trigger fragmentation
# ip xfrm policy add dir out src ::1 dst ::1 \
tmpl src ::1 dst ::1 proto esp spi 1
# ip xfrm state add src ::1 dst ::1 \
proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
# ip link set dev lo mtu 1500
2) Monitor the packet flow and set up an UDP sink
# tcpdump -ni lo -ttt &
# socat udp6-listen:12345,fork /dev/null &
3) Send a datagram that needs fragmentation with a connected socket
# perl -e 'print "@" x 1470 | socat - udp6:[::1]:12345
2016/06/07 18:52:52 socat[724] E read(3, 0x555bb3d5ba00, 8192): Protocol error
00:00:00.000000 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x2), length 1448
00:00:00.000014 IP6 ::1 > ::1: frag (1448|32)
00:00:00.000050 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x3), length 1272
(^ ICMPv6 Parameter Problem)
00:00:00.000022 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x5), length 136
4) Compare it to a non-connected socket
# perl -e 'print "@" x 1500' | socat - udp6-sendto:[::1]:12345
00:00:40.535488 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x6), length 1448
00:00:00.000010 IP6 ::1 > ::1: frag (1448|64)
What happens in step (3) is:
1) when connecting the socket in __ip6_datagram_connect(), we
perform an XFRM lookup, miss the flow cache, create an XFRM
bundle, and cache the destination,
2) afterwards, when sending the datagram, we perform an XFRM lookup,
again, miss the flow cache (due to mismatch of flowi6_iif and
flowi6_oif, which is an issue of its own), and recreate an XFRM
bundle based on the cached (and already transformed) destination.
To prevent the recreation of an XFRM bundle, avoid an XFRM lookup
altogether whenever we already have a destination entry cached in the
socket. This prevents the path MTU shrinkage and brings us on par with
UDPv4.
The fix also benefits connected PINGv6 sockets, another user of
ip6_sk_dst_lookup_flow(), who also suffer messages being transformed
twice.
Joint work with Hannes Frederic Sowa.
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting up ILA in a router we noticed that the the encapsulation
is invoked twice: once in the route input path and again upon route
output. To resolve this we add a flag set_csum_neutral for the
ila_update_ipv6_locator. If this flag is set and the checksum
neutral bit is also set we assume that checksum-neutral translation
has already been performed and take no further action. The
flag is set only in ila_output path. The flag is not set for ila_input and
ila_xlat.
Tested:
Used 3 netns to set to emulate a router and two hosts. The router
translates SIR addresses between the two destinations in other two netns.
Verified ping and netperf are functional.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for locally originated traffic to VRF-local IPv6 addresses.
Similar to IPv4 a local dst is set on the skb and the packet is
reinserted with a call to netif_rx. With this patch, ping, tcp and udp
packets to a local IPv6 address are successfully routed:
$ ip addr show dev eth1
4: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master red state UP group default qlen 1000
link/ether 02:e0:f9:1c:b9:74 brd ff:ff:ff:ff:ff:ff
inet 10.100.1.1/24 brd 10.100.1.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 2100:1::1/120 scope global
valid_lft forever preferred_lft forever
inet6 fe80::e0:f9ff:fe1c:b974/64 scope link
valid_lft forever preferred_lft forever
$ ping6 -c1 -I red 2100:1::1
ping6: Warning: source address might be selected on device other than red.
PING 2100:1::1(2100:1::1) from 2100:1::1 red: 56 data bytes
64 bytes from 2100:1::1: icmp_seq=1 ttl=64 time=0.098 ms
ip6_input is exported so the VRF driver can use it for the dst input
function. The dst_alloc function for IPv4 defaults to setting the input and
output functions; IPv6's does not. VRF does not need to duplicate the Rx path
so just export the ipv6 input function.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The v6 tcp stats scan do not provide TLP and ER timer information
correctly like the v4 version . This patch fixes that.
Fixes: 6ba8a3b19e ("tcp: Tail loss probe (TLP)")
Fixes: eed530b6c6 ("tcp: early retransmit")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_gso_network_seglen is not enough for checking fragment sizes if
skb is using GSO_BY_FRAGS as we have to check frag per frag.
This patch introduces skb_gso_validate_mtu, based on the former, which
will wrap the use case inside it as all calls to skb_gso_network_seglen
were to validate if it fits on a given TMU, and improve the check.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Tested-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Moore tracked a regression caused by a recent commit, which
mistakenly assumed that sk_filter() could be avoided if socket
had no current BPF filter.
The intent was to avoid udp_lib_checksum_complete() overhead.
But sk_filter() also checks skb_pfmemalloc() and
security_sock_rcv_skb(), so better call it.
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paul Moore <paul@paul-moore.com>
Tested-by: Paul Moore <paul@paul-moore.com>
Tested-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: samanthakumar <samanthakumar@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Fix incorrect timestamp in nfnetlink_queue introduced when addressing
y2038 safe timestamp, from Florian Westphal.
2) Get rid of leftover conntrack definition from the previous merge
window, oneliner from Florian.
3) Make nf_queue handler pernet to resolve race on dereferencing the
hook state structure with netns removal, from Eric Biederman.
4) Ensure clean exit on unregistered helper ports, from Taehee Yoo.
5) Restore FLOWI_FLAG_KNOWN_NH in nf_dup_ipv6. This got lost while
generalizing xt_TEE to add packet duplication support in nf_tables,
from Paolo Abeni.
6) Insufficient netlink NFTA_SET_TABLE attribute check in
nf_tables_getset(), from Phil Turnbull.
7) Reject helper registration on duplicated ports via modparams.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig options I added to work around broken compilation ended
up screwing up things more, as I used the wrong symbol to control
compilation of the file, resulting in IPv6 fou support to never be built
into the kernel.
Changing CONFIG_NET_FOU_IPV6_TUNNELS to CONFIG_IPV6_FOU fixes that
problem, I had renamed the symbol in one location but not the other,
and as the file is never being used by other kernel code, this did not
lead to a build failure that I would have caught.
After that fix, another issue with the same patch becomes obvious, as we
'select INET6_TUNNEL', which is related to IPV6_TUNNEL, but not the same,
and this can still cause the original build failure when IPV6_TUNNEL is
not built-in but IPV6_FOU is. The fix is equally trivial, we just need
to select the right symbol.
I have successfully build 350 randconfig kernels with this patch
and verified that the driver is now being built.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Fixes: fabb13db44 ("fou: add Kconfig options for IPv6 support")
Signed-off-by: David S. Miller <davem@davemloft.net>
With the commit 48e8aa6e31 ("ipv6: Set FLOWI_FLAG_KNOWN_NH at
flowi6_flags") ip6_pol_route() callers were asked to to set the
FLOWI_FLAG_KNOWN_NH properly and xt_TEE was updated accordingly,
but with the later refactor in commit bbde9fc182 ("netfilter:
factor out packet duplication for IPv4/IPv6") the flowi6_flags
update was lost.
This commit re-add it just before the routing decision.
Fixes: bbde9fc182 ("netfilter: factor out packet duplication for IPv4/IPv6")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
A previous patch added the fou6.ko module, but that failed to link
in a couple of configurations:
net/built-in.o: In function `ip6_tnl_encap_add_fou_ops':
net/ipv6/fou6.c:88: undefined reference to `ip6_tnl_encap_add_ops'
net/ipv6/fou6.c:94: undefined reference to `ip6_tnl_encap_add_ops'
net/ipv6/fou6.c:97: undefined reference to `ip6_tnl_encap_del_ops'
net/built-in.o: In function `ip6_tnl_encap_del_fou_ops':
net/ipv6/fou6.c:106: undefined reference to `ip6_tnl_encap_del_ops'
net/ipv6/fou6.c:107: undefined reference to `ip6_tnl_encap_del_ops'
If CONFIG_IPV6=m, ip6_tnl_encap_add_ops/ip6_tnl_encap_del_ops
are in a module, but fou6.c can still be built-in, and that
obviously fails to link.
Also, if CONFIG_IPV6=y, but CONFIG_IPV6_TUNNEL=m or
CONFIG_IPV6_TUNNEL=n, the same problem happens for a different
reason.
This adds two new silent Kconfig symbols to work around both
problems:
- CONFIG_IPV6_FOU is now always set to 'm' if either CONFIG_NET_FOU=m
or CONFIG_IPV6=m
- CONFIG_IPV6_FOU_TUNNEL is set implicitly when IPV6_FOU is enabled
and NET_FOU_IP_TUNNELS is also turned out, and it will ensure
that CONFIG_IPV6_TUNNEL is also available.
The options could be made user-visible as well, to give additional
room for configuration, but it seems easier not to bother users
with more choice here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: aa3463d65e ("fou: Add encap ops for IPv6 tunnels")
Signed-off-by: David S. Miller <davem@davemloft.net>
In gre6 xmit path, we are sending a GRE packet, so set fl6 proto
to IPPROTO_GRE properly.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creat an ip6gretap interface with an unreachable route,
the MTU is about 14 bytes larger than what was needed.
If the remote address is reachable:
ping6 2001:0:130::1 -c 2
PING 2001:0:130::1(2001:0:130::1) 56 data bytes
64 bytes from 2001:0:130::1: icmp_seq=1 ttl=64 time=1.46 ms
64 bytes from 2001:0:130::1: icmp_seq=2 ttl=64 time=81.1 ms
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses the same issue we had for IPv4 where enabling GRE with
an inner checksum cannot be supported with FOU/GUE due to the fact that
they will jump past the GRE header at it is treated like a tunnel header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since iptunnel_handle_offloads() is called in all paths we can
probably drop the block in ip6_tnl_xmit that was checking for
skb->encapsulation and resetting the inner headers.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to set dev features, use same values that are used in GREv6.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add a new fou6 module that provides encapsulation
operations for IPv6.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add encap_hlen and ip_tunnel_encap structure to ip6_tnl. Add functions
for getting encap hlen, setting up encap on a tunnel, performing
encapsulation operation.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When performing foo-over-UDP, UDP packets are processed by the
encapsulation handler which returns another protocol to process.
This may result in processing two (or more) protocols in the
loop that are marked as INET6_PROTO_FINAL. The actions taken
for hitting a final protocol, in particular the skb_postpull_rcsum
can only be performed once.
This patch set adds a check of a final protocol has been seen. The
rules are:
- If the final protocol has not been seen any protocol is processed
(final and non-final). In the case of a final protocol, the final
actions are taken (like the skb_postpull_rcsum)
- If a final protocol has been seen (e.g. an encapsulating UDP
header) then no further non-final protocols are allowed
(e.g. extension headers). For more final protocols the
final actions are not taken (e.g. skb_postpull_rcsum).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip6_input_finish the nexthdr protocol is retrieved from the
next header offset that is returned in the cb of the skb.
This method does not work for UDP encapsulation that may not
even have a concept of a nexthdr field (e.g. FOU).
This patch checks for a final protocol (INET6_PROTO_FINAL) when a
protocol handler returns > 0. If the protocol is not final then
resubmission is performed on nhoff value. If the protocol is final
then the nexthdr is taken to be the return value.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In several gso_segment functions there are checks of gso_type against
a seemingly arbitrary list of SKB_GSO_* flags. This seems like an
attempt to identify unsupported GSO types, but since the stack is
the one that set these GSO types in the first place this seems
unnecessary to do. If a combination isn't valid in the first
place that stack should not allow setting it.
This is a code simplication especially for add new GSO types.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_hdr() is slightly more expensive than using skb->data in contexts
where we know they point to the same byte.
In receive path, tcp_v4_rcv() and tcp_v6_rcv() are in this situation,
as tcp header has not been pulled yet.
In output path, the same can be said when we just pushed the tcp header
in the skb, in tcp_transmit_skb() and tcp_make_synack()
Also factorize the two checks for tcb->tcp_flags & TCPHDR_SYN in
tcp_transmit_skb() and pass tcp header pointer to tcp_ecn_send(),
so that compiler can further optimize and avoid a reload.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__sock_cmsg_send() might return different error codes, not only -EINVAL.
Fixes: 24025c465f ("ipv4: process socket-level control messages in IPv4")
Fixes: ad1e46a837 ("ipv6: process socket-level control messages in IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when creating or updating a route, no check is performed
in both ipv4 and ipv6 code to the hoplimit value.
The caller can i.e. set hoplimit to 256, and when such route will
be used, packets will be sent with hoplimit/ttl equal to 0.
This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4
ipv6 route code, substituting any value greater than 255 with 255.
This is consistent with what is currently done for ADVMSS and MTU
in the ipv4 code.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing an OpenStack configuration using VXLANs I saw the following
call trace:
RIP: 0010:[<ffffffff815fad49>] udp4_lib_lookup_skb+0x49/0x80
RSP: 0018:ffff88103867bc50 EFLAGS: 00010286
RAX: ffff88103269bf00 RBX: ffff88103269bf00 RCX: 00000000ffffffff
RDX: 0000000000004300 RSI: 0000000000000000 RDI: ffff880f2932e780
RBP: ffff88103867bc60 R08: 0000000000000000 R09: 000000009001a8c0
R10: 0000000000004400 R11: ffffffff81333a58 R12: ffff880f2932e794
R13: 0000000000000014 R14: 0000000000000014 R15: ffffe8efbfd89ca0
FS: 0000000000000000(0000) GS:ffff88103fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000488 CR3: 0000000001c06000 CR4: 00000000001426e0
Stack:
ffffffff81576515 ffffffff815733c0 ffff88103867bc98 ffffffff815fcc17
ffff88103269bf00 ffffe8efbfd89ca0 0000000000000014 0000000000000080
ffffe8efbfd89ca0 ffff88103867bcc8 ffffffff815fcf8b ffff880f2932e794
Call Trace:
[<ffffffff81576515>] ? skb_checksum+0x35/0x50
[<ffffffff815733c0>] ? skb_push+0x40/0x40
[<ffffffff815fcc17>] udp_gro_receive+0x57/0x130
[<ffffffff815fcf8b>] udp4_gro_receive+0x10b/0x2c0
[<ffffffff81605863>] inet_gro_receive+0x1d3/0x270
[<ffffffff81589e59>] dev_gro_receive+0x269/0x3b0
[<ffffffff8158a1b8>] napi_gro_receive+0x38/0x120
[<ffffffffa0871297>] gro_cell_poll+0x57/0x80 [vxlan]
[<ffffffff815899d0>] net_rx_action+0x160/0x380
[<ffffffff816965c7>] __do_softirq+0xd7/0x2c5
[<ffffffff8107d969>] run_ksoftirqd+0x29/0x50
[<ffffffff8109a50f>] smpboot_thread_fn+0x10f/0x160
[<ffffffff8109a400>] ? sort_range+0x30/0x30
[<ffffffff81096da8>] kthread+0xd8/0xf0
[<ffffffff81693c82>] ret_from_fork+0x22/0x40
[<ffffffff81096cd0>] ? kthread_park+0x60/0x60
The following trace is seen when receiving a DHCP request over a flow-based
VXLAN tunnel. I believe this is caused by the metadata dst having a NULL
dev value and as a result dev_net(dev) is causing a NULL pointer dereference.
To resolve this I am replacing the check for skb_dst(skb)->dev with just
skb->dev. This makes sense as the callers of this function are usually in
the receive path and as such skb->dev should always be populated. In
addition other functions in the area where these are called are already
using dev_net(skb->dev) to determine the namespace the UDP packet belongs
in.
Fixes: 63058308cd ("udp: Add udp6_lib_lookup_skb and udp4_lib_lookup_skb")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with WCCP in gre6 tunnel, it sets the wrong tpi->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not include attribute IFLA_GRE_TOS.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the VRF driver uses the rx_handler to switch the skb device
to the VRF device. Switching the dev prior to the ip / ipv6 layer
means the VRF driver has to duplicate IP/IPv6 processing which adds
overhead and makes features such as retaining the ingress device index
more complicated than necessary.
This patch moves the hook to the L3 layer just after the first NF_HOOK
for PRE_ROUTING. This location makes exposing the original ingress device
trivial (next patch) and allows adding other NF_HOOKs to the VRF driver
in the future.
dev_queue_xmit_nit is exported so that the VRF driver can cycle the skb
with the switched device through the packet taps to maintain current
behavior (tcpdump can be used on either the vrf device or the enslaved
devices).
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocol for 4in6 tunnel is IPPROTO_IPIP. This was wrongly changed by
the last cleanup.
CC: Tom Herbert <tom@herbertland.com>
Fixes: 0d3c703a9d ("ipv6: Cleanup IPv6 tunnel receive path")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handler 'ila_fill_encap_info' adds two attributes: ILA_ATTR_LOCATOR
and ILA_ATTR_CSUM_MODE.
nla_total_size_64bit() must be use for ILA_ATTR_LOCATOR.
Also, do nla_put_u8 instead of nla_put_u64 for ILA_ATTR_CSUM_MODE.
Fixes: f13a82d87b ("ipv6: use nla_put_u64_64bit()")
Fixes: 90bfe662db ("ila: add checksum neutral ILA translations")
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two spots where o_flags in a tunnel are being compared to GRE_SEQ
instead of TUNNEL_SEQ.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to use adjusted protocol value for setting inner protocol.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE for IPv6 does not properly translate for GRE flags to tunnel
flags and vice versa. This patch fixes that.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip6gre_tnl_link_config set t->tun_len and t->hlen correctly for the
configuration. For hard_header_len and mtu calculation include
IPv6 header and encapsulation overhead.
In ip6gre_tunnel_init_common set t->tun_len and t->hlen correctly for
the configuration. Revert to setting hard_header_len instead of
needed_headroom.
Tested:
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225
Gives MTU of 1434. That is equal to 1500 - 40 - 14 - 4 - 8.
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225 okey 123
Gives MTU of 1430. That is equal to 1500 - 40 - 14 - 4 - 8 - 4.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move l3mdev_rt6_dst_by_oif and l3mdev_get_saddr to l3mdev.c. Collapse
l3mdev_get_rt6_dst into l3mdev_rt6_dst_by_oif since it is the only
user and keep the l3mdev_get_rt6_dst name for consistency with other
hooks.
A follow-on patch adds more code to these functions making them long
for inlined functions.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following large patchset contains Netfilter updates for your
net-next tree. My initial intention was to send you this in two goes but
when I looked back twice I already had this burden on top of me.
Several updates for IPVS from Marco Angaroni:
1) Allow SIP connections originating from real-servers to be load
balanced by the SIP persistence engine as is already implemented
in the other direction.
2) Release connections immediately for One-packet-scheduling (OPS)
in IPVS, instead of making it via timer and rcu callback.
3) Skip deleting conntracks for each one packet in OPS, and don't call
nf_conntrack_alter_reply() since no reply is expected.
4) Enable drop on exhaustion for OPS + SIP persistence.
Miscelaneous conntrack updates from Florian Westphal, including fix for
hash resize:
5) Move conntrack generation counter out of conntrack pernet structure
since this is only used by the init_ns to allow hash resizing.
6) Use get_random_once() from packet path to collect hash random seed
instead of our compound.
7) Don't disable BH from ____nf_conntrack_find() for statistics,
use NF_CT_STAT_INC_ATOMIC() instead.
8) Fix lookup race during conntrack hash resizing.
9) Introduce clash resolution on conntrack insertion for connectionless
protocol.
Then, Florian's netns rework to get rid of per-netns conntrack table,
thus we use one single table for them all. There was consensus on this
change during the NFWS 2015 and, on top of that, it has recently been
pointed as a source of multiple problems from unpriviledged netns:
11) Use a single conntrack hashtable for all namespaces. Include netns
in object comparisons and make it part of the hash calculation.
Adapt early_drop() to consider netns.
12) Use single expectation and NAT hashtable for all namespaces.
13) Use a single slab cache for all namespaces for conntrack objects.
14) Skip full table scanning from nf_ct_iterate_cleanup() if the pernet
conntrack counter tells us the table is empty (ie. equals zero).
Fixes for nf_tables interval set element handling, support to set
conntrack connlabels and allow set names up to 32 bytes.
15) Parse element flags from element deletion path and pass it up to the
backend set implementation.
16) Allow adjacent intervals in the rbtree set type for dynamic interval
updates.
17) Add support to set connlabel from nf_tables, from Florian Westphal.
18) Allow set names up to 32 bytes in nf_tables.
Several x_tables fixes and updates:
19) Fix incorrect use of IS_ERR_VALUE() in x_tables, original patch
from Andrzej Hajda.
And finally, miscelaneous netfilter updates such as:
20) Disable automatic helper assignment by default. Note this proc knob
was introduced by a900689264 ("netfilter: nf_ct_helper: allow to
disable automatic helper assignment") 4 years ago to start moving
towards explicit conntrack helper configuration via iptables CT
target.
21) Get rid of obsolete and inconsistent debugging instrumentation
in x_tables.
22) Remove unnecessary check for null after ip6_route_output().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tables have to exist for VRFs to function. Ensure they exist
when VRF device is created.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Responses for packets to unused ports are getting lost with L3 domains.
IPv4 has ip_send_unicast_reply for sending TCP responses which accounts
for L3 domains; update the IPv6 counterpart tcp_v6_send_response.
For icmp the L3 master check needs to be moved up in icmp6_send
to properly respond to UDP packets to a port with no listener.
Fixes: ca254490c8 ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dprintf() and duprintf() functions are enabled at compile time,
these days we have better runtime debugging through pr_debug() and
static keys.
On top of this, this debugging is so old that I don't expect anyone
using this anymore, so let's get rid of this.
IP_NF_ASSERT() is still left in place, although this needs that
NETFILTER_DEBUG is enabled, I think these assertions provide useful
context information when reading the code.
Note that ARP_NF_ASSERT() has been removed as there is no user of
this.
Kill also DEBUG_ALLOW_ALL and a couple of pr_error() and pr_debug()
spots that are inconsistently placed in the code.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The ipv6 gre implementation was cleaned up to share more code
with the ipv4 version, but it can be enabled even when NET_IPGRE_DEMUX
is disabled, resulting in a link error:
net/built-in.o: In function `gre_rcv':
:(.text+0x17f5d0): undefined reference to `gre_parse_header'
ERROR: "gre_parse_header" [net/ipv6/ip6_gre.ko] undefined!
This adds a Kconfig dependency to prevent that now invalid
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 308edfdf15 ("gre6: Cleanup GREv6 receive path, call common GRE functions")
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's easier for gre_parse_header to return the header length instead of
filing it into a parameter. That way, the callers that don't care about the
header length can just check whether the returned value is lower than zero.
In gre_err, the tunnel header must not be pulled. See commit b7f8fe251e
("gre: do not pull header in ICMP error processing") for details.
This patch reduces the conflict between the mentioned commit and commit
95f5c64c3c ("gre: Move utility functions to common headers").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The handler 'ila_fill_encap_info' adds one attribute: ILA_ATTR_LOCATOR.
Fixes: 65d7ab8de5 ("net: Identifier Locator Addressing module")
CC: Tom Herbert <tom@herbertland.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the sendmsg function of UDP, raw, ICMP and l2tp sockets, we use local
variables like hlimits, tclass, opt and dontfrag and pass them to corresponding
functions like ip6_make_skb, ip6_append_data and xxx_push_pending_frames.
This is not a good practice and makes it hard to add new parameters.
This fix introduces a new struct ipcm6_cookie similar to ipcm_cookie in
ipv4 and include the above mentioned variables. And we only pass the
pointer to this structure to corresponding functions. This makes it easier
to add new parameters in the future and makes the function cleaner.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes in GREv6 transmit path:
- Call gre_checksum, remove gre6_checksum
- Rename ip6gre_xmit2 to __gre6_xmit
- Call gre_build_header utility function
- Call ip6_tnl_xmit common function
- Call ip6_tnl_change_mtu, eliminate ip6gre_tunnel_change_mtu
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few generic changes to generalize tunnels in IPv6:
- Export ip6_tnl_change_mtu so that it can be called by ip6_gre
- Add tun_hlen to ip6_tnl structure.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames ip6_tnl_xmit2 to ip6_tnl_xmit and exports it. Other
users like GRE will be able to call this. The original ip6_tnl_xmit
function is renamed to ip6_tnl_start_xmit (this is an ndo_start_xmit
function).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
