On the off chance that clock value ends up being too high (by means
of skl_ddi_calculate_wrpll() having been called with big enough
value of crtc_state->port_clock * 1000), one possible consequence
may be that the result will not be able to fit into signed int.
Fix this issue by moving conversion of clock parameter from kHz to Hz
into the body of skl_ddi_calculate_wrpll(), as well as casting the
same parameter to u64 type while calculating the value for AFE clock.
This both mitigates the overflow problem and avoids possible erroneous
integer promotion mishaps.
Found by Linux Verification Center (linuxtesting.org) with static
analysis tool SVACE.
Fixes: 82d3543701 ("drm/i915/skl: Implementation of SKL DPLL programming")
Cc: stable@vger.kernel.org
Signed-off-by: Nikita Zhandarovich <n.zhandarovich@fintech.ru>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240729174035.25727-1-n.zhandarovich@fintech.ru
AS SDP should be computed when VRR timing generator is also enabled.
Correct the compute condition to compute params of Adaptive sync SDP
when VRR timing genrator is enabled along with sink support indication.
--v2:
Modify if condition (Jani).
Fixes: b2013783c4 ("drm/i915/display: Cache adpative sync caps to use it later")
Cc: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Cc: Arun R Murthy <arun.r.murthy@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: intel-xe@lists.freedesktop.org
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
(added prefix drm in subject)
Link: https://patchwork.freedesktop.org/patch/msgid/20240730040941.396862-1-mitulkumar.ajitkumar.golani@intel.com
Clear VSC SDP if intel_dp_set_infoframes is called from post ddi disable
routine i.e with the variable of enable as false. This is to avoid
an infoframes.enable mismatch issue which is caused when pipe is
connected to eDp which has psr then connected to DPMST. In this case
eDp's post ddi disable routine does not clear infoframes.enable VSC
for the given pipe and DPMST does not recompute VSC SDP and write
infoframes.enable which causes a mismatch.
--v2
-Make the comment match the code [Jani]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240724163743.3668407-1-suraj.kandpal@intel.com
Sometimes during hotplug scenario or suspend/resume scenario encoder is
not always initialized when intel_hdcp_get_capability add
a check to avoid kernel null pointer dereference.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Dnyaneshwar Bhadane <dnyaneshwar.bhadane@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240722064451.3610512-2-suraj.kandpal@intel.com
I2C v7, SMBus 3.2, and I3C 1.1.1 specifications have replaced "master/slave"
with more appropriate terms. Inspired by Wolfram's series to fix drivers/i2c/,
fix the terminology for users of I2C_ALGOBIT bitbanging interface, now that
the approved verbiage exists in the specification.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: Zhi Wang <zhiwang@kernel.org>
Signed-off-by: Easwar Hariharan <eahariha@linux.microsoft.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240711052734.1273652-4-eahariha@linux.microsoft.com
After a bad link state is detected, the sink capabilities with which the
link was originally trained could have changed: for instance another
sink got connected or the retraining was forced after the rate/lane count
got decreased (as a fallback). In these cases the retraining modeset
fails as expected also printing a debug message, so don't WARN on it.
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240712135724.660399-3-imre.deak@intel.com
After the previous patch link training happens always with a valid
atomic state, so remove the NOTE comments and asserts which required a
valid state only for DP-MST and allowed for a NULL state for DP-SST.
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240712135724.660399-2-imre.deak@intel.com
Instead of direct calls of the link training functions, use a modeset
commit to retrain a DP link in SST mode, similarly to how this is done
in DP-MST mode. Originally the current way was chosen presumedly,
because there wasn't a well-established way in place for the driver to
do an internal (vs. userspace/kernel client) commit. Since then such
internal commits became a common place (initial-, HDMI/TC link reset
commit), so there is no reason to handle the DP-SST link-retraining case
differently.
At the end of the current sequence the HW reported a FIFO underrun -
without other issues visible to users - because during retraining the
link's encoder/port was disabled/re-enabled without also
disabling/re-enabling the corresponding pipe/transcoder (as required by
the spec); the corresponding underrun error message was suppressed as a
known issue. Based on Ankit's test on DG2 the underrun error was still
reported as it got detected with some (vblank) delay wrt. other
platforms. Switching to a modeset commit resolves these underrun related
issues.
Cc: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240712135724.660399-1-imre.deak@intel.com
Pull the code to determine the maximum CFB height
into a separate function.
To make this work we need to declare an explicit max height
for all older platforms as well. But that is actually just
the max plane height as pre-HSW hardware supposedly doesn't
have the trick of leaving the extra lines uncompressed.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240705145254.3355-12-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Rename intel_fbc_hw_tracking_covers_screen() to intel_fbc_surface_size_ok()
so that the naming scheme is the same for the surface size vs. plane
size checks. "surface size" is what bspec talks about.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240705145254.3355-7-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Extract intel_fbc_max_plane_size() from intel_fbc_plane_size_valid().
We'll have another use for this soon in determining how much stolen
memory we'd like to keep reserved for FBC.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240705145254.3355-5-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
_intel_fbc_cfb_stride() calculates the CFB stride the hardware would
automagically generate from the plane's stride. Rename the function
to intel_fbc_plane_cfb_stride() to better reflect its purpose.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240705145254.3355-4-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Switch the FBC code over to intel_display from i915, as
much as possible. This is the future direction so that
the display code can be shared between i915 and xe more
cleanly.
Some of the platform checks and the stolen mem facing stiff
still need i915 around though.
v2: Drop some redundant to_i915() casts
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240705145254.3355-3-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Give vrr_enabling() and vrr_disabling() slightly fancier names, and
pass in the whole atomic state so that they'll be easier to use.
We'll need to call at least the disabling part from the DSB code
soon enough (so that we can do vblank evasions/etc. correctly on
the DSB).
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240624191032.27333-3-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Calculate the vblank delay in the vblank evasion code correctly
for interlaced modes.
The current code assumes that we won't be using an interlaced mode.
That assumption is actually valid since we've defeatured interlaced
scanout in commit f71c9b7bc3 ("drm/i915/display: Prune Interlace
modes for Display >=12") for DSB capable platforms. However the
feature is still present in the hardware, and if we ever find the
need to re-enable it seems better to calculate the vblank delay
correctly.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240624191032.27333-2-ville.syrjala@linux.intel.com
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Nothing depends on the cached LTTPR mode, however for consistency keep
it up-to-date with the value programmed to the DPCD register.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240708190029.271247-5-imre.deak@intel.com
After detection the cached LTTPR count can be checked to determine if
LTTPRs in non-transparent mode were detected. Reset the cached LTTPR
count if the reported number of LTTPRs is invalid to ensure the above
checks work as expected.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240708190029.271247-4-imre.deak@intel.com
Switching to transparent mode leads to a loss of link synchronization,
so prevent doing this on an active link. This happened at least on an
Intel N100 system / DELL UD22 dock, the LTTPR residing either on the
host or the dock. To fix the issue, keep the current mode on an active
link, adjusting the LTTPR count accordingly (resetting it to 0 in
transparent mode).
v2: Adjust code comment during link training about reiniting the LTTPRs.
(Ville)
Fixes: 7b2a4ab8b0 ("drm/i915: Switch to LTTPR transparent mode link training")
Reported-and-tested-by: Gareth Yu <gareth.yu@intel.com>
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/10902
Cc: <stable@vger.kernel.org> # v5.15+
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240708190029.271247-3-imre.deak@intel.com
Regularly retraining a link during an atomic commit happens with the
given pipe/link already disabled and hence intel_dp->link_trained being
false. Ensure this also for retraining a DP SST link via direct calls to
the link training functions (vs. an actual commit as for DP MST). So far
nothing depended on this, however the next patch will depend on
link_trained==false for changing the LTTPR mode to non-transparent.
Cc: <stable@vger.kernel.org> # v5.15+
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240708190029.271247-2-imre.deak@intel.com
The dispcnlunit1_cp_xosc_clk should be de-asserted in display off
and only asserted in display on. As part of this workaround, Display
driver shall execute set-reset sequence at the end of the initialize
sequence to ensure clk does not remain active in display OFF.
--v2:
- Rebase.
--v3:
- Correct HSD number in commit message.
--v4:
- Reformat commit message.
- Use intel_de_rmw instead of intel_de_write
--v5:
- Build Fixes.
WA: 15013987218
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Nemesa Garg <nemesa.garg@intel.com>
Reviewed-by: Suraj Kandpal <suraj.kandpal@intel.com>
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240708083247.2611258-1-mitulkumar.ajitkumar.golani@intel.com
Add new member to struct intel_dp to cache support of Adaptive Sync
SDP capabilities and use it whenever required to avoid HW access
to read capability during each atomic commit.
-v2:
- Squash both the patches
Signed-off-by: Mitul Golani <mitulkumar.ajitkumar.golani@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240704082638.2302092-2-mitulkumar.ajitkumar.golani@intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Starting with Xe_LPD+, although FIA is still used to readout Type-C pin
assignment, part of Type-C support is moved to PICA and programming
PORT_TX_DFLEXDPMLE1(*) registers is not applicable anymore like it was
for previous display IPs (e.g. see BSpec 49190).
v2:
- Mention Bspec 49190 as a reference of instructions for previous
IPs. (Shekhar Chauhan)
- s/Xe_LPDP/Xe_LPD+/ in the commit message. (Matt Roper)
- Update commit message to be more accurate to the changes in the IP.
(Imre Deak)
Bspec: 65750, 65448
Reviewed-by: Shekhar Chauhan <shekhar.chauhan@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240625202652.315936-1-gustavo.sousa@intel.com
Signed-off-by: Gustavo Sousa <gustavo.sousa@intel.com>
In TBT-alt mode the driver doesn't program the PHY's PLL, which is
handled instead by Thunderbolt driver/FW components, hence the PLL's HW
vs. SW state verification should be skipped. During HW readout set a flag
in the PLL state if the port was at the moment in TBT-alt mode and skip
the verification of PLL parameters in this case.
Fixes: 45fe957ae7 ("drm/i915/display: Add compare config for MTL+ platforms")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/11258
Cc: Mika Kahola <mika.kahola@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240626170813.806470-1-imre.deak@intel.com
DSB_STATUS bit 16 is supposed to be a sticky bit informing us whether
the DSB was idle or not when the pipe's delayed vblank (when double
buffered registers latch) occurred. Unfortunately it turns out this
is a level triggred signal, ie. the bit will be set whenever the
DSB is busy during the scanline window between start of delayed
vblank and vtotal. Try to document that fact by renaming the bit.
Sadly this also thwarts my plan to use this bit to sanity check
that the (to be introduced) DSB based vblank evasion did its job
correctly. That would require an edge triggered signal instead.
So looks like we'll have to rely mostly on luck instead :(
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240611133344.30673-12-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
There are couple of bits in PSR2_CTL which needs to be written in case of
eDP Panel Replay
Bspec: 68920
v2: use boolean instead of assuming eDP Panel Replay mean Early Transport
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619062131.4021196-12-jouni.hogander@intel.com
Move Early Transport validity check to be performed for Panel Replay as
well and use Early Transport for eDP Panel Replay always.
v2:set crtc_state->enable_psr2_su_region_et directly (not in if block)
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619062131.4021196-11-jouni.hogander@intel.com
eDP1.5 support ALPM with Panel Replay as well. We need to check ALPM
related things for Panel Replay as well.
Bspec: 68920
v5:
- instead of using crtc_state->has_panel_replay provide aux_less flag
v4:
- do not move _compute_psr2_sdp_prior_scanline_indication
- move ALPM related checks to separate function
v3: move vblank check as well
v2: do not move Vblank >= PSR2_CTL Block Count Number maximum line count
check
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619062131.4021196-9-jouni.hogander@intel.com
Take into account in Panel Replay compute config that HW will not allow PR
on eDP when HDCP enabled.
v2: add debug message to print out why Panel Replay is not possible
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619062131.4021196-7-jouni.hogander@intel.com
Take into account that 128b/132b Panel Replay is not supported on eDP.
Bspec: 68920
v2:
- make crtc_state as const
- add debug message to print out why Panel Replay is not possible
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619062131.4021196-6-jouni.hogander@intel.com
eDP1.5 allows Panel Replay on eDP as well. Take this into account when
enabling sink PSR/Panel Replay. Write also PANEL_REPLAY_CONFIG2 register
accordingly.
v3:
- set DP_PANEL_REPLAY_CRC_VERIFICATION in PANEL_REPLAY_CONFIG2
- PANEL_REPLAY_CONFIG2 is available in DP2.1 as well
v2: do not configure ALPM for DP2.0 Panel Replay
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Animesh Manna <animesh.manna@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240619062131.4021196-4-jouni.hogander@intel.com
