Commit 264640fc2c ("ipv6: distinguish frag queues by device
for multicast and link-local packets") modified the ipv6 fragment
reassembly logic to distinguish frag queues by device for multicast
and link-local packets but in fact only the main reassembly code
limits the use of the device to those address types and the netfilter
reassembly code uses the device for all packets.
This means that if fragments of a packet arrive on different interfaces
then netfilter will fail to reassemble them and the fragments will be
expired without going any further through the filters.
Fixes: 648700f76b ("inet: frags: use rhashtables for reassembly units")
Signed-off-by: Tom Hughes <tom@compton.nu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch is based on the discussions between Neal Cardwell and
Eric Dumazet in the link
https://lore.kernel.org/netdev/20240726204105.1466841-1-quic_subashab@quicinc.com/
It was correctly pointed out that tp->window_clamp would not be
updated in cases where net.ipv4.tcp_moderate_rcvbuf=0 or if
(copied <= tp->rcvq_space.space). While it is expected for most
setups to leave the sysctl enabled, the latter condition may
not end up hitting depending on the TCP receive queue size and
the pattern of arriving data.
The updated check should be hit only on initial MSS update from
TCP_MIN_MSS to measured MSS value and subsequently if there was
an update to a larger value.
Fixes: 05f76b2d63 ("tcp: Adjust clamping window for applications specifying SO_RCVBUF")
Signed-off-by: Sean Tranchetti <quic_stranche@quicinc.com>
Signed-off-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ssn_offset field is u32 and is placed into the netlink response with
nla_put_u32(), but only 2 bytes are reserved for the attribute payload
in subflow_get_info_size() (even though it makes no difference
in the end, as it is aligned up to 4 bytes). Supply the correct
argument to the relevant nla_total_size() call to make it less
confusing.
Fixes: 5147dfb508 ("mptcp: allow dumping subflow context to userspace")
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Reviewed-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240812065024.GA19719@asgard.redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A recent change to the driver exposed a bug where the MAC RX
filters (unicast MAC, broadcast MAC, and multicast MAC) are
configured and enabled before the RX path is fully initialized.
The result of this bug is that after the PHY is started packets
that match these MAC RX filters start to flow into the RX FIFO.
And then, after rx_init() is completed, these packets will go
into the driver RX ring as well. If enough packets are received
to fill the RX ring (default size is 128 packets) before the call
to request_irq() completes, the driver RX function becomes stuck.
This bug is intermittent but is most likely to be seen where the
oob_net0 interface is connected to a busy network with lots of
broadcast and multicast traffic.
All the MAC RX filters must be disabled until the RX path is ready,
i.e. all initialization is done and all the IRQs are installed.
Fixes: f7442a634a ("mlxbf_gige: call request_irq() after NAPI initialized")
Reviewed-by: Asmaa Mnebhi <asmaa@nvidia.com>
Signed-off-by: David Thompson <davthompson@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240809163612.12852-1-davthompson@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After napi_complete_done() is called when NAPI is polling in the current
process context, another NAPI may be scheduled and start running in
softirq on another CPU and may ring the doorbell before the current CPU
does. When combined with unnecessary rings when there is no need to arm
the CQ, it triggers error paths in the hardware.
This patch fixes this by calling napi_complete_done() after doorbell
rings. It limits the number of unnecessary rings when there is
no need to arm. MANA hardware specifies that there must be one doorbell
ring every 8 CQ wraparounds. This driver guarantees one doorbell ring as
soon as the number of consumed CQEs exceeds 4 CQ wraparounds. In practical
workloads, the 4 CQ wraparounds proves to be big enough that it rarely
exceeds this limit before all the napi weight is consumed.
To implement this, add a per-CQ counter cq->work_done_since_doorbell,
and make sure the CQ is armed as soon as passing 4 wraparounds of the CQ.
Cc: stable@vger.kernel.org
Fixes: e1b5683ff6 ("net: mana: Move NAPI from EQ to CQ")
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Long Li <longli@microsoft.com>
Link: https://patch.msgid.link/1723219138-29887-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In macb_suspend(), idev->ifa_list is fetched with rcu_access_pointer()
and later the pointer is dereferenced as ifa->ifa_local.
So, idev->ifa_list must be fetched with rcu_dereference().
Fixes: 0cb8de39a7 ("net: macb: Add ARP support to WOL")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Link: https://patch.msgid.link/20240808040021.6971-1-kuniyu@amazon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When there are multiple ap interfaces on one band and with WED on,
turning the interface down will cause a kernel panic on MT798X.
Previously, cb_priv was freed in mtk_wed_setup_tc_block() without
marking NULL,and mtk_wed_setup_tc_block_cb() didn't check the value, too.
Assign NULL after free cb_priv in mtk_wed_setup_tc_block() and check NULL
in mtk_wed_setup_tc_block_cb().
----------
Unable to handle kernel paging request at virtual address 0072460bca32b4f5
Call trace:
mtk_wed_setup_tc_block_cb+0x4/0x38
0xffffffc0794084bc
tcf_block_playback_offloads+0x70/0x1e8
tcf_block_unbind+0x6c/0xc8
...
---------
Fixes: 799684448e ("net: ethernet: mtk_wed: introduce wed wo support")
Signed-off-by: Zheng Zhang <everything411@qq.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MANA driver's RX buffer alloc_size is passed into napi_build_skb() to
create SKB. skb_shinfo(skb) is located at the end of skb, and its alignment
is affected by the alloc_size passed into napi_build_skb(). The size needs
to be aligned properly for better performance and atomic operations.
Otherwise, on ARM64 CPU, for certain MTU settings like 4000, atomic
operations may panic on the skb_shinfo(skb)->dataref due to alignment fault.
To fix this bug, add proper alignment to the alloc_size calculation.
Sample panic info:
[ 253.298819] Unable to handle kernel paging request at virtual address ffff000129ba5cce
[ 253.300900] Mem abort info:
[ 253.301760] ESR = 0x0000000096000021
[ 253.302825] EC = 0x25: DABT (current EL), IL = 32 bits
[ 253.304268] SET = 0, FnV = 0
[ 253.305172] EA = 0, S1PTW = 0
[ 253.306103] FSC = 0x21: alignment fault
Call trace:
__skb_clone+0xfc/0x198
skb_clone+0x78/0xe0
raw6_local_deliver+0xfc/0x228
ip6_protocol_deliver_rcu+0x80/0x500
ip6_input_finish+0x48/0x80
ip6_input+0x48/0xc0
ip6_sublist_rcv_finish+0x50/0x78
ip6_sublist_rcv+0x1cc/0x2b8
ipv6_list_rcv+0x100/0x150
__netif_receive_skb_list_core+0x180/0x220
netif_receive_skb_list_internal+0x198/0x2a8
__napi_poll+0x138/0x250
net_rx_action+0x148/0x330
handle_softirqs+0x12c/0x3a0
Cc: stable@vger.kernel.org
Fixes: 80f6215b45 ("net: mana: Add support for jumbo frame")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missed property phys, which indicate how connect to serdes phy.
Fix below warning:
arch/arm64/boot/dts/freescale/fsl-lx2160a-honeycomb.dtb: fsl-mc@80c000000: dpmacs:ethernet@7: Unevaluated properties are not allowed ('phys' was unexpected)
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pawel Dembicki says:
====================
net: dsa: vsc73xx: fix MDIO bus access and PHY opera
This series are extracted patches from net-next series [0].
The VSC73xx driver has issues with PHY configuration. This patch series
fixes most of them.
The first patch synchronizes the register configuration routine with the
datasheet recommendations.
Patches 2-3 restore proper communication on the MDIO bus. Currently,
the write value isn't sent to the MDIO register, and without a busy check,
communication with the PHY can be interrupted. This causes the PHY to
receive improper configuration and autonegotiation could fail.
The fourth patch removes the PHY reset blockade, as it is no longer
required.
After fixing the MDIO operations, autonegotiation became possible.
The last patch removes the blockade, which became unnecessary after
the MDIO operations fix.
[0] https://patchwork.kernel.org/project/netdevbpf/list/?series=874739&state=%2A&archive=both
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vsc73xx mdio bus work properly, the generic autonegotiation
configuration works well.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the VSC73xx PHY was problematic because the MDIO bus, without
a busy check, read and wrote incorrect register values.
My investigation indicates that resetting the PHY only triggers changes
in configuration. However, improper register values written earlier
were only exposed after a soft reset.
The reset itself wasn't the issue; rather, the problem stemmed from
incorrect read and write operations.
A 'soft_reset' can now proceed normally. There are no reasons to keep
the VSC73xx from being reset.
This commit removes the reset blockade in the 'vsc73xx_phy_write'
function.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VSC73xx has a busy flag used during MDIO operations. It is raised
when MDIO read/write operations are in progress. Without it, PHYs are
misconfigured and bus operations do not work as expected.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the 'vsc73xx_phy_write' function, the register value is missing,
and the phy write operation always sends zeros.
This commit passes the value variable into the proper register.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the datasheet description ("Port Mode Procedure" in 5.6.2),
the VSC73XX_MAC_CFG_WEXC_DIS bit is configured only for half duplex mode.
The WEXC_DIS bit is responsible for MAC behavior after an excessive
collision. Let's set it as described in the datasheet.
Fixes: 05bd97fc55 ("net: dsa: Add Vitesse VSC73xx DSA router driver")
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In axiethernet header fix register defines comment description to be
inline with IP documentation. It updates MAC configuration register,
MDIO configuration register and frame filter control description.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't dereference "skb" after calling vcc->push() because the skb
is released.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ueue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-08-07 (igc)
This series contains updates to igc driver only.
Faizal adjusts the size of the MAC internal buffer on i226 devices to
resolve an errata for leaking packet transmits. He also corrects a
condition in which qbv_config_change_errors are incorrectly counted.
Lastly, he adjusts the conditions for resetting the adapter when
changing TSN Tx mode and corrects the conditions in which gtxoffset
register is set.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
`ip_hdr(skb)->ihl << 2` is the same as `ip_hdrlen(skb)`
Therefore, we should use a well-defined function not a bit shift
to find the header length.
It also compresses two lines to a single line.
Signed-off-by: Moon Yeounsu <yyyynoom@gmail.com>
Reviewed-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan says:
====================
mlx5 misc fixes 2024-08-08
This patchset provides misc bug fixes from the team to the mlx5 core and
Eth drivers.
====================
Link: https://patch.msgid.link/20240808144107.2095424-1-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Previously, an ethtool rx flow with no attrs would not be added to the
NIC as it has no rules to configure the hw with, but it would be
reported as successful to the caller (return code 0). This is confusing
for the user as ethtool then reports "Added rule $num", but no rule was
actually added.
This change corrects that by instead reporting these wrong rules as
-EINVAL.
Fixes: b29c61dac3 ("net/mlx5e: Ethtool steering flow validation refactoring")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20240808144107.2095424-5-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mlx5e_safe_reopen_channels() requires the state lock taken. The
referenced changed in the Fixes tag removed the lock to fix another
issue. This patch adds it back but at a later point (when calling
mlx5e_safe_reopen_channels()) to avoid the deadlock referenced in the
Fixes tag.
Fixes: eab0da3891 ("net/mlx5e: Fix possible deadlock on mlx5e_tx_timeout_work")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Link: https://lore.kernel.org/all/ZplpKq8FKi3vwfxv@gmail.com/T/
Reviewed-by: Breno Leitao <leitao@debian.org>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20240808144107.2095424-4-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
During latency tests (netperf TCP_RR) a 30% degradation of HW GRO vs SW
GRO was observed. This is due to SHAMPO triggering timeout filler CQEs
instead of delivering the CQE for the packet.
Having a short timeout for SHAMPO doesn't bring any benefits as it is
the driver that does the merging, not the hardware. On the contrary, it
can have a negative impact: additional filler CQEs are generated due to
the timeout. As there is no way to disable this timeout, this change
sets it to the maximum value.
Instead of using the packet_merge.timeout parameter which is also used
for LRO, set the value directly when filling in the rest of the SHAMPO
parameters in mlx5e_build_rq_param().
Fixes: 99be56171f ("net/mlx5e: SHAMPO, Re-enable HW-GRO")
Signed-off-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20240808144107.2095424-3-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Unconditionally calling the MPIR query on BF separate mode yields the FW
syndrome below [1]. Do not call it unless admin clearly specified the SD
group, i.e. expressing the intention of using the multi-PF netdev
feature.
This fix covers cases not covered in
commit fca3b47918 ("net/mlx5: Do not query MPIR on embedded CPU function").
[1]
mlx5_cmd_out_err:808:(pid 8267): ACCESS_REG(0x805) op_mod(0x1) failed,
status bad system state(0x4), syndrome (0x685f19), err(-5)
Fixes: 678eb44805 ("net/mlx5: SD, Implement basic query and instantiation")
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Link: https://patch.msgid.link/20240808144107.2095424-2-tariqt@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After enabling UDP GSO for devices not offering checksum offload, we have
hit a regression where a bad offload warning can be triggered when sending
a datagram with IPv6 extension headers.
Extend the UDP GSO IPv6 tests to cover this scenario.
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://patch.msgid.link/20240808-udp-gso-egress-from-tunnel-v4-3-f5c5b4149ab9@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In commit 10154dbded ("udp: Allow GSO transmit from devices with no
checksum offload") we have intentionally allowed UDP GSO packets marked
CHECKSUM_NONE to pass to the GSO stack, so that they can be segmented and
checksummed by a software fallback when the egress device lacks these
features.
What was not taken into consideration is that a CHECKSUM_NONE skb can be
handed over to the GSO stack also when the egress device advertises the
tx-udp-segmentation / NETIF_F_GSO_UDP_L4 feature.
This will happen when there are IPv6 extension headers present, which we
check for in __ip6_append_data(). Syzbot has discovered this scenario,
producing a warning as below:
ip6tnl0: caps=(0x00000006401d7869, 0x00000006401d7869)
WARNING: CPU: 0 PID: 5112 at net/core/dev.c:3293 skb_warn_bad_offload+0x166/0x1a0 net/core/dev.c:3291
Modules linked in:
CPU: 0 PID: 5112 Comm: syz-executor391 Not tainted 6.10.0-rc7-syzkaller-01603-g80ab5445da62 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 06/07/2024
RIP: 0010:skb_warn_bad_offload+0x166/0x1a0 net/core/dev.c:3291
[...]
Call Trace:
<TASK>
__skb_gso_segment+0x3be/0x4c0 net/core/gso.c:127
skb_gso_segment include/net/gso.h:83 [inline]
validate_xmit_skb+0x585/0x1120 net/core/dev.c:3661
__dev_queue_xmit+0x17a4/0x3e90 net/core/dev.c:4415
neigh_output include/net/neighbour.h:542 [inline]
ip6_finish_output2+0xffa/0x1680 net/ipv6/ip6_output.c:137
ip6_finish_output+0x41e/0x810 net/ipv6/ip6_output.c:222
ip6_send_skb+0x112/0x230 net/ipv6/ip6_output.c:1958
udp_v6_send_skb+0xbf5/0x1870 net/ipv6/udp.c:1292
udpv6_sendmsg+0x23b3/0x3270 net/ipv6/udp.c:1588
sock_sendmsg_nosec net/socket.c:730 [inline]
__sock_sendmsg+0xef/0x270 net/socket.c:745
____sys_sendmsg+0x525/0x7d0 net/socket.c:2585
___sys_sendmsg net/socket.c:2639 [inline]
__sys_sendmmsg+0x3b2/0x740 net/socket.c:2725
__do_sys_sendmmsg net/socket.c:2754 [inline]
__se_sys_sendmmsg net/socket.c:2751 [inline]
__x64_sys_sendmmsg+0xa0/0xb0 net/socket.c:2751
do_syscall_x64 arch/x86/entry/common.c:52 [inline]
do_syscall_64+0xf3/0x230 arch/x86/entry/common.c:83
entry_SYSCALL_64_after_hwframe+0x77/0x7f
[...]
</TASK>
We are hitting the bad offload warning because when an egress device is
capable of handling segmentation offload requested by
skb_shinfo(skb)->gso_type, the chain of gso_segment callbacks won't produce
any segment skbs and return NULL. See the skb_gso_ok() branch in
{__udp,tcp,sctp}_gso_segment helpers.
To fix it, force a fallback to software USO when processing a packet with
IPv6 extension headers, since we don't know if these can checksummed by
all devices which offer USO.
Fixes: 10154dbded ("udp: Allow GSO transmit from devices with no checksum offload")
Reported-by: syzbot+e15b7e15b8a751a91d9a@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/all/000000000000e1609a061d5330ce@google.com/
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Link: https://patch.msgid.link/20240808-udp-gso-egress-from-tunnel-v4-2-f5c5b4149ab9@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
UDP segmentation offload inherently depends on checksum offload. It should
not be possible to disable checksum offload while leaving USO enabled.
Enforce this dependency in code.
There is a single tx-udp-segmentation feature flag to indicate support for
both IPv4/6, hence the devices wishing to support USO must offer checksum
offload for both IP versions.
Fixes: 10154dbded ("udp: Allow GSO transmit from devices with no checksum offload")
Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20240808-udp-gso-egress-from-tunnel-v4-1-f5c5b4149ab9@cloudflare.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Apart from the standard "configurations", "interfaces" and "alternate
interface settings" in USB, iOS devices also have a notion of
"modes". In different modes, the device exposes a different set of
available configurations.
Depending on the iOS version, and depending on the current mode, the
length and contents of the carrier state control message differs:
* 1 byte (seen on iOS 4.2.1, 8.4):
* 03: carrier off (mode 0)
* 04: carrier on (mode 0)
* 3 bytes (seen on iOS 10.3.4, 15.7.6):
* 03 03 03: carrier off (mode 0)
* 04 04 03: carrier on (mode 0)
* 4 bytes (seen on iOS 16.5, 17.6):
* 03 03 03 00: carrier off (mode 0)
* 04 03 03 00: carrier off (mode 1)
* 06 03 03 00: carrier off (mode 4)
* 04 04 03 04: carrier on (mode 0 and 1)
* 06 04 03 04: carrier on (mode 4)
Before this change, the driver always used the first byte of the
response to determine carrier state.
From this larger sample, the first byte seems to indicate the number of
available USB configurations in the current mode (with the exception of
the default mode 0), and in some cases (namely mode 1 and 4) does not
correlate with the carrier state.
Previous logic erroneously counted `04 03 03 00` as "carrier on" and
`06 04 03 04` as "carrier off" on iOS versions that support mode 1 and
mode 4 respectively.
Only modes 0, 1 and 4 expose the USB Ethernet interfaces necessary for
the ipheth driver.
Check the second byte of the control message where possible, and fall
back to checking the first byte on older iOS versions.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX callbacks can fail for multiple reasons:
* Payload too short
* Payload formatted incorrecly (e.g. bad NCM framing)
* Lack of memory
None of these should cause the driver to seize up.
Make such failures non-critical and continue processing further
incoming URBs.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
On iPhone 15 Pro Max one can observe periodic URBs with no payload
on the "bulk in" (RX) endpoint. These don't seem to do anything
meaningful. Reproduced on iOS 17.5.1 and 17.6.
This behaviour isn't observed on iPhone 11 on the same iOS version. The
nature of these zero-length URBs is so far unknown.
Drop RX URBs with no payload.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx URB length was already checked in ipheth_rcvbulk_callback_legacy()
and ipheth_rcvbulk_callback_ncm(), depending on the current mode.
The check in ipheth_rcvbulk_callback() was thus mostly a duplicate.
The only place in ipheth_rcvbulk_callback() where we care about the URB
length is for the initial control frame. These frames are always 4 bytes
long. This has been checked as far back as iOS 4.2.1 on iPhone 3G.
Remove the extraneous URB length check. For control frames, check for
the specific 4-byte length instead.
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ipheth_sndbulk_callback() can submit carrier_work
as a part of its error handling. That means that
the driver must make sure that the work is cancelled
after it has made sure that no more URB can terminate
with an error condition.
Hence the order of actions in ipheth_close() needs
to be inverted.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Foster Snowhill <forst@pen.gy>
Tested-by: Georgi Valkov <gvalkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - regressions:
- eth: bnxt_en: fix memory out-of-bounds in bnxt_fill_hw_rss_tbl()
on older chips
Current release - new code bugs:
- ethtool: fix off-by-one error / kdoc contradicting the code
for max RSS context IDs
- Bluetooth: hci_qca:
- QCA6390: fix support on non-DT platforms
- QCA6390: don't call pwrseq_power_off() twice
- fix a NULL-pointer derefence at shutdown
- eth: ice: fix incorrect assigns of FEC counters
Previous releases - regressions:
- mptcp: fix handling endpoints with both 'signal' and 'subflow'
flags set
- virtio-net: fix changing ring count when vq IRQ coalescing not
supported
- eth: gve: fix use of netif_carrier_ok() during reconfig / reset
Previous releases - always broken:
- eth: idpf: fix bugs in queue re-allocation on reconfig / reset
- ethtool: fix context creation with no parameters
Misc:
- linkwatch: use system_unbound_wq to ease RTNL contention
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bKTC
-----END PGP SIGNATURE-----
Merge tag 'net-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bluetooth.
Current release - regressions:
- eth: bnxt_en: fix memory out-of-bounds in bnxt_fill_hw_rss_tbl() on
older chips
Current release - new code bugs:
- ethtool: fix off-by-one error / kdoc contradicting the code for max
RSS context IDs
- Bluetooth: hci_qca:
- QCA6390: fix support on non-DT platforms
- QCA6390: don't call pwrseq_power_off() twice
- fix a NULL-pointer derefence at shutdown
- eth: ice: fix incorrect assigns of FEC counters
Previous releases - regressions:
- mptcp: fix handling endpoints with both 'signal' and 'subflow'
flags set
- virtio-net: fix changing ring count when vq IRQ coalescing not
supported
- eth: gve: fix use of netif_carrier_ok() during reconfig / reset
Previous releases - always broken:
- eth: idpf: fix bugs in queue re-allocation on reconfig / reset
- ethtool: fix context creation with no parameters
Misc:
- linkwatch: use system_unbound_wq to ease RTNL contention"
* tag 'net-6.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (41 commits)
net: dsa: microchip: disable EEE for KSZ8567/KSZ9567/KSZ9896/KSZ9897.
ethtool: Fix context creation with no parameters
net: ethtool: fix off-by-one error in max RSS context IDs
net: pse-pd: tps23881: include missing bitfield.h header
net: fec: Stop PPS on driver remove
net: bcmgenet: Properly overlay PHY and MAC Wake-on-LAN capabilities
l2tp: fix lockdep splat
net: stmmac: dwmac4: fix PCS duplex mode decode
idpf: fix UAFs when destroying the queues
idpf: fix memleak in vport interrupt configuration
idpf: fix memory leaks and crashes while performing a soft reset
bnxt_en : Fix memory out-of-bounds in bnxt_fill_hw_rss_tbl()
net: dsa: bcm_sf2: Fix a possible memory leak in bcm_sf2_mdio_register()
net/smc: add the max value of fallback reason count
Bluetooth: hci_sync: avoid dup filtering when passive scanning with adv monitor
Bluetooth: l2cap: always unlock channel in l2cap_conless_channel()
Bluetooth: hci_qca: fix a NULL-pointer derefence at shutdown
Bluetooth: hci_qca: fix QCA6390 support on non-DT platforms
Bluetooth: hci_qca: don't call pwrseq_power_off() twice for QCA6390
ice: Fix incorrect assigns of FEC counts
...
- Have reading of event format files test if the meta data still exists.
When a event is freed, a flag (EVENT_FILE_FL_FREED) in the meta data is
set to state that it is to prevent any new references to it from happening
while waiting for existing references to close. When the last reference
closes, the meta data is freed. But the "format" was missing a check to
this flag (along with some other files) that allowed new references to
happen, and a use-after-free bug to occur.
- Have the trace event meta data use the refcount infrastructure instead
of relying on its own atomic counters.
- Have tracefs inodes use alloc_inode_sb() for allocation instead of
using kmem_cache_alloc() directly.
- Have eventfs_create_dir() return an ERR_PTR instead of NULL as
the callers expect a real object or an ERR_PTR.
- Have release_ei() use call_srcu() and not call_rcu() as all the
protection is on SRCU and not RCU.
- Fix ftrace_graph_ret_addr() to use the task passed in and not current.
- Fix overflow bug in get_free_elt() where the counter can overflow
the integer and cause an infinite loop.
- Remove unused function ring_buffer_nr_pages()
- Have tracefs freeing use the inode RCU infrastructure instead of
creating its own. When the kernel had randomize structure fields
enabled, the rcu field of the tracefs_inode was overlapping the
rcu field of the inode structure, and corrupting it. Instead,
use the destroy_inode() callback to do the initial cleanup of
the code, and then have free_inode() free it.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCZrTvXxQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qu39AP9ze6ELpShDrxbXhf0adbNqG2IXMepa
MMLqfq8tU8E/vAEAuZXJ6rKXeGvKeONa06ocvWJ0dpb2cy/n4hmx+KtM5gI=
=Pkh4
-----END PGP SIGNATURE-----
Merge tag 'trace-v6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull tracing fixes from Steven Rostedt:
- Have reading of event format files test if the metadata still exists.
When a event is freed, a flag (EVENT_FILE_FL_FREED) in the metadata
is set to state that it is to prevent any new references to it from
happening while waiting for existing references to close. When the
last reference closes, the metadata is freed. But the "format" was
missing a check to this flag (along with some other files) that
allowed new references to happen, and a use-after-free bug to occur.
- Have the trace event meta data use the refcount infrastructure
instead of relying on its own atomic counters.
- Have tracefs inodes use alloc_inode_sb() for allocation instead of
using kmem_cache_alloc() directly.
- Have eventfs_create_dir() return an ERR_PTR instead of NULL as the
callers expect a real object or an ERR_PTR.
- Have release_ei() use call_srcu() and not call_rcu() as all the
protection is on SRCU and not RCU.
- Fix ftrace_graph_ret_addr() to use the task passed in and not
current.
- Fix overflow bug in get_free_elt() where the counter can overflow the
integer and cause an infinite loop.
- Remove unused function ring_buffer_nr_pages()
- Have tracefs freeing use the inode RCU infrastructure instead of
creating its own.
When the kernel had randomize structure fields enabled, the rcu field
of the tracefs_inode was overlapping the rcu field of the inode
structure, and corrupting it. Instead, use the destroy_inode()
callback to do the initial cleanup of the code, and then have
free_inode() free it.
* tag 'trace-v6.11-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracefs: Use generic inode RCU for synchronizing freeing
ring-buffer: Remove unused function ring_buffer_nr_pages()
tracing: Fix overflow in get_free_elt()
function_graph: Fix the ret_stack used by ftrace_graph_ret_addr()
eventfs: Use SRCU for freeing eventfs_inodes
eventfs: Don't return NULL in eventfs_create_dir()
tracefs: Fix inode allocation
tracing: Use refcount for trace_event_file reference counter
tracing: Have format file honor EVENT_FILE_FL_FREED
Assorted little stuff:
- lockdep fixup for lockdep_set_notrack_class()
- we can now remove a device when using erasure coding without
deadlocking, though we still hit other issues
- the "allocator stuck" timeout is now configurable, and messages are
ratelimited; default timeout has been increased from 10 seconds to 30
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEKnAFLkS8Qha+jvQrE6szbY3KbnYFAma05JwACgkQE6szbY3K
bnYE+Q//VJ6R/UxDoxjk8zgftRcdgwXod6U+/E0Kj3ZBKLYXkcGaWWmmGMkFafBp
eL7Y3wtHSKiMsHYX9KEdFUZFLe1KI4c16RgNIXk9nwkF+3/+8pEDHKPFuoGHJH3O
HComHGqwVg8Zx2jRNvEkvQ980iH7OBGhCjMFXhJ3xbMGLdw91TQQi49a+Q/vz7QT
y3Cl1dgX5xBl7fqKefsYa+X6mpWi4/6t60vJvatI+bvDfznjI6jN3qGVLlQye7tC
6VbJAjHsPPyNMlWa99UaHqDdaM325zR2ES0bsfHd8Up4iAwO8OgjzYQxpYTgi51i
6DTiGEOV2S8gF+Rnprnbzsnau0hEvrtQY2Ub85TCIGbZJa8b+aDIlq9k8jF36O2E
2CUTleQ/E129RxXpkZGsVRpNmemdCi6rHAcluaFEgezX4FJH8BVOwQQq2Xz7rd7E
3ZP5iAWmX0IgOL0VOCP/ZXl/lEMwSk0VAED3jEbT7f2K7rU9nXDO2bIEx1wXDCm1
b32kvmUi2FBjqLHSqvAPEb52tvvZuliMUY7z9dEx+AX9AVC9kGE+amGexosKb/LY
nWzey+D0cKHtgbkMFrCClkpg75Tnt9ISJbad53+5qhN8an/a71djdj8Zk0UQnQjv
6Amv4Ns1lDo3XGC1QtYkF5HqiWaupbUXAftptpS4Av4X1zZEQIc=
=q1dD
-----END PGP SIGNATURE-----
Merge tag 'bcachefs-2024-08-08' of git://evilpiepirate.org/bcachefs
Pull bcachefs fixes from Kent Overstreet:
"Assorted little stuff:
- lockdep fixup for lockdep_set_notrack_class()
- we can now remove a device when using erasure coding without
deadlocking, though we still hit other issues
- the 'allocator stuck' timeout is now configurable, and messages are
ratelimited. The default timeout has been increased from 10 seconds
to 30"
* tag 'bcachefs-2024-08-08' of git://evilpiepirate.org/bcachefs:
bcachefs: Use bch2_wait_on_allocator() in btree node alloc path
bcachefs: Make allocator stuck timeout configurable, ratelimit messages
bcachefs: Add missing path_traverse() to btree_iter_next_node()
bcachefs: ec should not allocate from ro devs
bcachefs: Improved allocator debugging for ec
bcachefs: Add missing bch2_trans_begin() call
bcachefs: Add a comment for bucket helper types
bcachefs: Don't rely on implicit unsigned -> signed integer conversion
lockdep: Fix lockdep_set_notrack_class() for CONFIG_LOCK_STAT
bcachefs: Fix double free of ca->buckets_nouse
Russell King reported that the arm cbc(aes) crypto module hangs when
loaded, and Herbert Xu bisected it to commit 9b9879fc03 ("modules:
catch concurrent module loads, treat them as idempotent"), and noted:
"So what's happening here is that the first modprobe tries to load a
fallback CBC implementation, in doing so it triggers a load of the
exact same module due to module aliases.
IOW we're loading aes-arm-bs which provides cbc(aes). However, this
needs a fallback of cbc(aes) to operate, which is made out of the
generic cbc module + any implementation of aes, or ecb(aes). The
latter happens to also be provided by aes-arm-cb so that's why it
tries to load the same module again"
So loading the aes-arm-bs module ends up wanting to recursively load
itself, and the recursive load then ends up waiting for the original
module load to complete.
This is a regression, in that it used to be that we just tried to load
the module multiple times, and then as we went on to install it the
second time we would instead just error out because the module name
already existed.
That is actually also exactly what the original "catch concurrent loads"
patch did in commit 9828ed3f69 ("module: error out early on concurrent
load of the same module file"), but it turns out that it ends up being
racy, in that erroring out before the module has been fully initialized
will cause failures in dependent module loading.
See commit ac2263b588 (which was the revert of that "error out early")
commit for details about why erroring out before the module has been
initialized is actually fundamentally racy.
Now, for the actual recursive module load (as opposed to just
concurrently loading the same module twice), the race is not an issue.
At the same time it's hard for the kernel to see that this is recursion,
because the module load is always done from a usermode helper, so the
recursion is not some simple callchain within the kernel.
End result: this is not the real fix, but this at least adds a warning
for the situation (admittedly much too late for all the debugging pain
that Russell and Herbert went through) and if we can come to a
resolution on how to detect the recursion properly, this re-organizes
the code to make that easier.
Link: https://lore.kernel.org/all/ZrFHLqvFqhzykuYw@shell.armlinux.org.uk/
Reported-by: Russell King <linux@armlinux.org.uk>
Debugged-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=aEeY
-----END PGP SIGNATURE-----
Merge tag 'loongarch-fixes-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Enable general EFI poweroff method to make poweroff usable on
hardwares which lack ACPI S5, use accessors to page table entries
instead of direct dereference to avoid potential problems, and two
trivial kvm cleanups"
* tag 'loongarch-fixes-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch: KVM: Remove undefined a6 argument comment for kvm_hypercall()
LoongArch: KVM: Remove unnecessary definition of KVM_PRIVATE_MEM_SLOTS
LoongArch: Use accessors to page table entries instead of direct dereference
LoongArch: Enable general EFI poweroff method
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2024-08-07 (ice)
This series contains updates to ice driver only.
Grzegorz adds IRQ synchronization call before performing reset and
prevents writing to hardware when it is resetting.
Mateusz swaps incorrect assignment of FEC statistics.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue:
ice: Fix incorrect assigns of FEC counts
ice: Skip PTP HW writes during PTP reset procedure
ice: Fix reset handler
====================
Link: https://patch.msgid.link/20240807224521.3819189-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The 'at least one change' requirement is not applicable for context
creation, skip the check in such case.
This allows a command such as 'ethtool -X eth0 context new' to work.
The command works by mistake when using older versions of userspace
ethtool due to an incompatibility issue where rxfh.input_xfrm is passed
as zero (unset) instead of RXH_XFRM_NO_CHANGE as done with recent
userspace. This patch does not try to solve the incompatibility issue.
Link: https://lore.kernel.org/netdev/05ae8316-d3aa-4356-98c6-55ed4253c8a7@nvidia.com/
Fixes: 84a1d9c482 ("net: ethtool: extend RXNFC API to support RSS spreading of filter matches")
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Reviewed-by: Jianbo Liu <jianbol@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/20240807173352.3501746-1-gal@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Both ethtool_ops.rxfh_max_context_id and the default value used when
it's not specified are supposed to be exclusive maxima (the former
is documented as such; the latter, U32_MAX, cannot be used as an ID
since it equals ETH_RXFH_CONTEXT_ALLOC), but xa_alloc() expects an
inclusive maximum.
Subtract one from 'limit' to produce an inclusive maximum, and pass
that to xa_alloc().
Increase bnxt's max by one to prevent a (very minor) regression, as
BNXT_MAX_ETH_RSS_CTX is an inclusive max. This is safe since bnxt
is not actually hard-limited; BNXT_MAX_ETH_RSS_CTX is just a
leftover from old driver code that managed context IDs itself.
Rename rxfh_max_context_id to rxfh_max_num_contexts to make its
semantics (hopefully) more obvious.
Fixes: 847a8ab186 ("net: ethtool: let the core choose RSS context IDs")
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://patch.msgid.link/5a2d11a599aa5b0cc6141072c01accfb7758650c.1723045898.git.ecree.xilinx@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using FIELD_GET() fails in configurations that don't already include
the header file indirectly:
drivers/net/pse-pd/tps23881.c: In function 'tps23881_i2c_probe':
drivers/net/pse-pd/tps23881.c:755:13: error: implicit declaration of function 'FIELD_GET' [-Wimplicit-function-declaration]
755 | if (FIELD_GET(TPS23881_REG_DEVID_MASK, ret) != TPS23881_DEVICE_ID) {
| ^~~~~~~~~
Fixes: 89108cb5c2 ("net: pse-pd: tps23881: Fix the device ID check")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20240807075455.2055224-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some Wake-on-LAN modes such as WAKE_FILTER may only be supported by the MAC,
while others might be only supported by the PHY. Make sure that the .get_wol()
returns the union of both rather than only that of the PHY if the PHY supports
Wake-on-LAN.
Fixes: 7e400ff35c ("net: bcmgenet: Add support for PHY-based Wake-on-LAN")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240806175659.3232204-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
