There are a few rooms for improvements wrt the debug prints:
- The EP debug print is shown only at starting, not at stopping
- The EP debug print contains useless object addresses
- Some helpers show the urb and the EP object addresses, too
This patch addresses those shortcomings.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The sync EP setup isn't cleared at stopping the stream but expected to
be cleared at the next stream start. This may leave the sync link
setup stale and can spoof wrongly when full duplex streams were
running in the implicit fb sync. Let's initialize them properly at
start and end of the stream.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Factor out the code to obtain snd_usb_endpoint object matching with
the given endpoint. It'll be used in the later patch to add the
implicit feedback hw-constraint.
No functional change by this patch itself.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-6-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It seems that many UAC2 devices are with the implicit feedback, but
they couldn't be probed properly because the assumption the driver
takes currently isn't applied: they have the single endpoint for both
data and implicit-fb streams, while we checked only the classical sync
endpoints assigned to the next altsetting in the same interface.
This patch extends the search to match with those typical cases where
the implicit fb stream is found in the next interface number.
While we're at it, slightly refactor the code, not returning 0/-ERROR
but use the standard bool to success/failur, which is more intuitive
in this particular case.
Reported-by: Dylan Robinson <dylan_robinson@motu.com>
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The current driver code assumes blindly that all found sample rates for
the same endpoint from the UAC2 and UAC3 descriptors can be used no
matter which altsetting, but actually this was wrong: some devices
accept only limited sample rates in each altsetting. For determining
which altsetting supports which rate, we need to verify each sample rate
and check the validity via UAC2_AS_VAL_ALT_SETTINGS. This control
reports back the available altsettings as a bitmap.
This patch implements the missing piece above, the verification and
reconstructs the sample rate tables based on the result.
An open question is how to deal with the altsettings that ended up
with no valid sample rates after verification. At least, there is a
device that showed this problem although the sample rates did work in
the later usage (see bug link). For now, we accept such an altset as
is, assuming that it's a firmware bug.
Reported-by: Dylan Robinson <dylan_robinson@motu.com>
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1178203
Link: https://lore.kernel.org/r/20201123085347.19667-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The PCM trigger callback is atomic, hence we must not call a function
like usb_set_interface() there. Calling it from there would lead to a
kernel Oops.
Fix it by moving the usb_set_interface() call to set_sync_endpoint().
Also, apply the snd_usb_set_interface_quirk() for consistency, too.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In the current code, when the device provides the discrete sample rate
tables with unusual sample rates, the driver tries to gather the whole
values from the audioformat entries and create a hw-constraint rule to
restrict with this single rate list. This is rather inefficient and
may overlook the rates that are associated only with the certain
audioformat entries.
This patch improves the hw constraint setup by rewriting the existing
hw_rule_rate(). The discrete sample rates (identified by rate_table
and nr_rates of format entry) are checked in the existing
hw_rule_rate() instead of extra rules; in the case of discrete rates,
the function compares with each rate table entry and calculates the
min/max values from there. For the contiguous rates, the behavior
doesn't change.
Along with it, snd_usb_pcm_check_knot() and snb_usb_substream
rate_list field become superfluous, thus those are dropped.
Tested-by: Keith Milner <kamilner@superlative.org>
Tested-by: Dylan Robinson <dylan_robinson@motu.com>
Link: https://lore.kernel.org/r/20201123085347.19667-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of driver specific fixes, mostly for x86 systems (or CODECs
used mostly on x86) and all for relatively minor issues, the biggest one
being fixing S24_LE format on Keem Bay systems.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl+2peUACgkQJNaLcl1U
h9COxAf/aq+7DrGjU1umHPD/zfS3ppjmN1hNCHBxqiCm1U9SBbBLGlnDMMcPqFQR
wS8SKdDfhKONA7q7fhGDvvFZd07r9HzIFra+9HVjuc5ouKlPkoETF8uDfXqAdOkM
sXkffe45Wh9DqWIPZOng8ZpKVGW6v3oUCAMrlx53t9LUT9Sd8oQrhsx3nwgr/CUb
SmZiBFF5kWpK8CgG82PuDlCHEnsI4SEatYqHtEMYRBfE0K8fzROye7e7WCKBsb/8
QaDf1RrQ599GXLMVJzbFsXpybBwaaP7LWkKCDHfQbAeKZ6EAWH0agbvUq2X1H2nm
/a3Th5SgL6Vm6KXYvIFGHyTq8rbPLg==
=OkNz
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.10-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.11
A collection of driver specific fixes, mostly for x86 systems (or CODECs
used mostly on x86) and all for relatively minor issues, the biggest one
being fixing S24_LE format on Keem Bay systems.
The code change for switching to non-atomic mode brought the
unexpected mutex deadlock in get_msg(). It converted the spinlock
with the existing mutex, but there were calls with the already holding
the mutex. Since the only place that needs the extra lock is the code
path from snd_mixart_send_msg(), remove the mutex lock in get_msg()
and apply in the caller side for fixing the mutex deadlock.
Fixes: 8d3a8b5cb5 ("ALSA: mixart: Use nonatomic PCM ops")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201119121440.18945-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_PCI=n leads to a compile warning like:
sound/pci/hda/patch_ca0132.c:8214:10: warning: no case matching constant switch condition '0'
due to the missed handling of QUIRK_NONE in ca0132_mmio_init().
Fix it.
Fixes: bf2aa9ccc8 ("ALSA: hda/ca0132 - Cleanup ca0132_mmio_init function.")
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20201119120404.16833-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In kabylake_set_bias_level(), enabling mclk may fail if the clock has
already been enabled by the firmware. Attempts to disable that clock
later will fail with a warning backtrace.
mclk already disabled
WARNING: CPU: 2 PID: 108 at drivers/clk/clk.c:952 clk_core_disable+0x1b6/0x1cf
...
Call Trace:
clk_disable+0x2d/0x3a
kabylake_set_bias_level+0x72/0xfd [snd_soc_kbl_rt5663_rt5514_max98927]
snd_soc_card_set_bias_level+0x2b/0x6f
snd_soc_dapm_set_bias_level+0xe1/0x209
dapm_pre_sequence_async+0x63/0x96
async_run_entry_fn+0x3d/0xd1
process_one_work+0x2a9/0x526
...
Only disable the clock if it has been enabled.
Fixes: 15747a8020 ("ASoC: eve: implement set_bias_level function for rt5514")
Cc: Brent Lu <brent.lu@intel.com>
Cc: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201111205434.207610-1-linux@roeck-us.net
Signed-off-by: Mark Brown <broonie@kernel.org>
Found one more Logitech device, BCC950 ConferenceCam, which needs
the same delay here. This makes 3 out of 3 devices I have tried.
Therefore, add a delay for all Logitech devices as it does not hurt.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: <stable@vger.kernel.org> # 4.19.y, 5.4.y
Link: https://lore.kernel.org/r/20201117122803.24310-1-joakim.tjernlund@infinera.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During stream start DSP firmware requires LPCS disabled as that moment in
time is resource heavy. Currently high-clock is selected on start of
second stream onwards while low-clock is re-selected before stream
actually leaves RESUME state i.e. PAUSE_STREAM call. Fix this by always
updating clock before RESUME_STREAM and directly after PAUSE_STREAM.
Fixes: a126750fc8 ("ASoC: Intel: catpt: PCM operations")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201116133332.8530-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Playing with very low period sizes may lead to timeouts when awaiting
RESET_STREAM reply for offload streams. This is caused by NOTIFY_POSITION
appearing in the middle of trigger(stop).
Stream is unprepared during trigger(stop) where PAUSE_STREAM IPC gets
invoked. However, all data that is already mixed in DSP firmware's mixer
stream will still be played regardless of the pause. For offload streams,
this means possibility for another NOTIFY_POSITION to process. Keep these
notifications in check by only handling them when stream is in prepared
state.
Fixes: a126750fc8 ("ASoC: Intel: catpt: PCM operations")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20201116133332.8530-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
lpass_pcm_data is not freed in error paths. Free it in
error paths to avoid memory leak.
Fixes: 022d00ee0b ("ASoC: lpass-platform: Fix broken pcm data usage")
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/1605416210-14530-1-git-send-email-srivasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
S24_LE is 24 bit audio in 32 bit container configuration
Fixing the configuration to match the data arrangement of
this audio format.
Fixes: c5477e9667 ("ASoC: Intel: Add KeemBay platform driver")
Signed-off-by: Michael Sit Wei Hong <michael.wei.hong.sit@intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201116061905.32431-2-michael.wei.hong.sit@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spin_lock/unlock_irq() functions cannot be nested. The problem is
that presumably we would want the IRQs to be re-enabled on the second
call the spin_unlock_irq() but instead it will be enabled at the first
call so IRQs will be enabled earlier than expected.
In this situation the copy_resp_to_buf() function is only called from
one function and it is called with IRQs disabled. We can just use
the regular spin_lock/unlock() functions.
Fixes: 555e8a8f7f ("ALSA: fireworks: Add command/response functionality into hwdep interface")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201113101241.GB168908@mwanda
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To meet the most platform, the detection time should be increased to
avoid that the flushing DAC data fails.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20201113092125.19206-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When processing request to add/replace user-defined element set, check
of given element identifier and decision of numeric identifier is done
in "__snd_ctl_add_replace()" helper function. When the result of check
is wrong, the helper function returns error code. The error code shall
be returned to userspace application.
Current implementation includes bug to return zero to userspace application
regardless of the result. This commit fixes the bug.
Cc: <stable@vger.kernel.org>
Fixes: e1a7bfe380 ("ALSA: control: Fix race between adding and removing a user element")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20201113092043.16148-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
System boot or warm boot with plugged headset.
If it turn on power save mode, Headset Mic will lose.
This patch will solve this issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1ae4d98e92c147b780ace3911c4e1d73@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP Pavilion x360 Convertible machine, it supported mute led.
GPIO4 high will turn on led.
The patch will enable control led via GPIO4 pin.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1ae4d98e92c147b780ace3911c4e1d73@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix "use as headset mic, without its own jack detect" problem.
[ Minor coding style fixes by tiwai ]
Signed-off-by: PeiSen Hou <pshou@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/481963e4a5694ff19f27ae1e283d79ad@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add delay to fix pop noise from speaker.
Signed-off-by: Jack Yu <jack.yu@realtek.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20201105030804.31115-1-jack.yu@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A batch of driver specific fixes that have come up since the merge
window, nothing particularly major here but all good to have.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl+kBYgACgkQJNaLcl1U
h9BDHQf9HDn/narvcVdfCBdWI0uI/P5sETaQUw69J1PquiCtn8P2MzyaIofTGJbX
IiWEQE+Z1FnUgcs/KAQwKuvlp5UQ+L/6VlTPATgxEOcnNb82rN1riJjHI4C+5UXj
+KShaJy0afLcva3HL1NOuzUPvj1TZ+j07JiW7uqhEd3H/+O3VlXvUFWlZeXcDiNn
5hd+r4fKybfYrydR/kpE2JBW7E+0JhcOgztBhw/p3K0js+ovaDolSDVgonwcOtPE
/yDhISEkSzQ7wWYc4FjROryQJ5e4HtLEc9RumiqHVDXVg51uT3z8U/aEttlXVKR9
lEGZw+xNlnqDi/LDqYvJn1CER6iklw==
=Pe6G
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.10-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.10
A batch of driver specific fixes that have come up since the merge
window, nothing particularly major here but all good to have.
This patch fixes audio distortion on playback for the Allen&Heath
Qu-16.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201104115717.GA19046@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Validity bits (bit 28) must not be set in order to have the samples
valid. Some controllers look for this bit and ignore the samples if it
is set.
Fixes: 06ca24e98e ("ASoC: mchp-spdiftx: add driver for S/PDIF TX Controller")
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20201104155738.68403-1-codrin.ciubotariu@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes audio distortion on playback for the Yamaha MODX.
Signed-off-by: Geoffrey D. Bennett <g@b4.vu>
Tested-by: Frank Slotta <frank.slotta@posteo.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201104120705.GA19126@b4.vu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Khadas audio devices ( USB_ID_VENDOR 0x3353 )
have DSD-capable implementations from XMOS
need add new usb vendor id for recognition
Signed-off-by: Artem Lapkin <art@khadas.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201103103311.5435-1-art@khadas.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ASUS TM420 had depop circuit for headphone.
It need to turn on by COEF bit.
[ fixed the missing enum definition by tiwai ]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/3d6177d7023b4783bf2793861c577ada@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is harmless, but the "addr" comes from the user and it could lead
to a negative shift or to shift wrapping if it's too high.
Fixes: 0b00a5615d ("ALSA: hdac_ext: add hdac extended controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20201103101807.GC1127762@mwanda
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Disable MI2S bit clock from PAUSE/STOP/SUSPEND usecase instead of
shutdown time. Acheive this by invoking clk_disable API from
cpu daiops trigger instead of cpu daiops shutdown.
Change non-atomic API "clk_prepare_enable" to atomic API
"clk_enable" in trigger, as trigger is being called from atomic context.
Fixes: 7e6799d8f8 ("ASoC: qcom: lpass-cpu: Enable MI2S BCLK and LRCLK together")
Signed-off-by: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/1603098363-9251-1-git-send-email-srivasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Update SC7180 lpass_variant structure with proper I2S bitwidth
field bit positions, as bitwidth denotes 0 to 1 bits,
but previously used only 0 bit.
Signed-off-by: V Sujith Kumar Reddy <vsujithk@codeaurora.org>
Signed-off-by: Srinivasa Rao Mandadapu <srivasam@codeaurora.org>
Link: https://lore.kernel.org/r/1603798474-4897-1-git-send-email-srivasam@codeaurora.org
Signed-off-by: Mark Brown <broonie@kernel.org>
digital gain range is -84dB min to 40dB max, however this was not
correctly specified in the range.
Fix this by with correct range!
Fixes: 8c4f021d80 ("ASoC: wcd9335: add basic controls")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20201028154340.17090-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
digital gain range is -84dB min to 40dB max, however this was not
correctly specified in the range.
Fix this by with correct range!
Fixes: 1cde8b8223 ("ASoC: wcd934x: add basic controls")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20201028154340.17090-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The broken jack detection should be fixed by commit a6e7d0a4bd ("ALSA:
hda: fix jack detection with Realtek codecs when in D3"), let's try
enabling runtime PM by default again.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20201027130038.16463-4-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Both pm_runtime_force_suspend() and pm_runtime_force_resume() have
some implicit checks, so it can make code flow more straightforward if
we separate runtime and system suspend callbacks.
High Definition Audio Specification, 4.5.9.3 Codec Wake From System S3
states that codec can wake the system up from S3 if WAKEEN is toggled.
Since HDA controller has different wakeup settings for runtime and
system susend, we also need to explicitly disable direct-complete which
can be enabled automatically by PCI core. In addition to that, avoid
waking up codec if runtime resume is for system suspend, to not break
direct-complete for codecs.
While at it, also remove AZX_DCAPS_SUSPEND_SPURIOUS_WAKEUP, as the
original bug commit a6630529ae ("ALSA: hda: Workaround for spurious
wakeups on some Intel platforms") solves doesn't happen with this
patch.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20201027130038.16463-3-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Upon system resume, hda_codec_pm_resume() uses hda_codec_force_resume()
to resume the codec. However, pm_runtime_force_resume() won't really
resume the codec because of pm_runtime_need_not_resume() check.
Hence, hda_codec_force_resume() schedules a jackpoll work, which is to
really power up the codec.
Instead of doing that, we can use direct-complete to make the PM flow
more straightforward, and keep codec always suspended through system PM
flow if conditions are met.
On system suspend, PM core will decide what to do based on
hda_codec_pm_prepare():
- If codec is not runtime-suspended, PM core will suspend and resume the
device as normal.
- If codec is runtime-suspended, PM core will try to keep it suspended.
If it's still suspended after system resume, we use
hda_codec_pm_complete() to resume codec if it's needed.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20201027130038.16463-2-kai.heng.feng@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
System boot with plugged headset. It will not detect headset Mic.
It will happen on cold boot restart resume state.
Quirk by SSID change to quirk by pin verb.
Fixes: 13468bfa8c ("ALSA: hda/realtek - set mic to auto detect on a HP AIO machine")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/f42ae1ede1cf47029ae2bef1a42caf03@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Zoom UAC-2 USB audio interface provides an async playback endpoint
("1 OUT (ASYNC)") and capture endpoint ("2 IN (ASYNC)"), both with
2-channel S32_LE in 44.1, 48, 88.2, 96, 176.4, or 192
kilosamples/s. The device provides explicit feedback to adjust the
host's playback rate, but the feedback appears unstable and biased
relative to the device's capture rate.
"alsaloop -t 1000" experiences playback underruns and tries to
resample the captured audio to match the varying playback
rate. Forcing the kernel to use implicit feedback appears to
produce more stable results. This causes the host to transmit one
playback sample for each capture sample received. (Zoom North America
has been notified of this change.)
Signed-off-by: Keith Winstein <keithw@cs.stanford.edu>
Tested-by: Keith Winstein <keithw@cs.stanford.edu>
Cc: <stable@vger.kernel.org>
BugLink: https://lore.kernel.org/r/20201027071841.GA164525@trolley.csail.mit.edu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kernel-doc markups should use this format:
identifier - description
There is a common comment marked, instead, with kernel-doc
notation.
Some identifiers have different names between their prototypes
and the kernel-doc markup.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/535182d6f55d7a7de293dda9676df68f5f60afc6.1603469755.git.mchehab+huawei@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
Just a few additional small and trivial fixes.
-----BEGIN PGP SIGNATURE-----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=sYVq
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few additional small and trivial fixes"
* tag 'sound-fix-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix the return value if cb func is already registered
ALSA: usb-audio: Line6 Pod Go interface requires static clock rate quirk
ALSA: hda/ca0132: make some const arrays static, makes object smaller
ALSA: sparc: dbri: fix repeated word 'the'
Do not emit a warning for extended firmware header fields that are
not used by kernel. This creates unnecessary noise to kernel logs like:
sof-audio-pci 0000:00:1f.3: warning: unknown ext header type 3 size 0x1c
sof-audio-pci 0000:00:1f.3: warning: unknown ext header type 4 size 0x10
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20201021182419.1160391-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A delay must be introduced before the shutdown down of the mclk,
as stated in CS42L51 datasheet. Otherwise the codec may
produce some noise after the end of DAPM power down sequence.
The delay between DAC and CLOCK_SUPPLY widgets is too short.
Add a delay in mclk shutdown request to manage the shutdown delay
explicitly. From experiments, at least 10ms delay is necessary.
Set delay to 20ms as recommended in Documentation/timers/timers-howto.rst
when using msleep().
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Link: https://lore.kernel.org/r/20201020150109.482-1-olivier.moysan@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the current state of code, we would endup with something like
below in /proc/asound/cards for 2 machines based on this driver.
Machine 1:
0 [DB845c ]: DB845c - DB845c
DB845c
Machine 2:
0 [LenovoYOGAC6301]: Lenovo-YOGA-C63 - Lenovo-YOGA-C630-13Q50
LENOVO-81JL-LenovoYOGAC630_13Q50-LNVNB161216
This is not very UCM friendly both w.r.t to common up configs and
card identification, and UCM2 became totally not usefull with just
one ucm sdm845.conf for two machines which have different setups
w.r.t HDMI and other dais.
Reasons for such thing is partly because Qualcomm machine drivers never
cared to set driver_name.
This patch sets up driver name for the this driver to sort out the
UCM integration issues!
after this patch contents of /proc/asound/cards:
Machine 1:
0 [DB845c ]: sdm845 - DB845c
DB845c
Machine 2:
0 [LenovoYOGAC6301]: sdm845 - Lenovo-YOGA-C630-13Q50
LENOVO-81JL-LenovoYOGAC630_13Q50-LNVNB161216
with this its possible to align with what UCM2 expects and we can have
sdm845/DB845.conf
sdm845/LENOVO-81JL-LenovoYOGAC630_13Q50-LNVNB161216.conf
... for board variants. This should scale much better!
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20201023095849.22894-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
