APM X-Gene SoC AHCI SATA Host controller driver requires
some correction of Phy Control OOB timing for the
COMINIT/COMWAKE parameters to correctly interoperate with
different kinds of disks.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As per SATA IO specification, when Host sends HOLD, the device takes
about 20DW latency to reply to HOLDA. In some case, device doesn't
response to HOLDA over 20DW and causes FIFO goes into over flow
condition. Due to this condition, device enumerations fails with
those devices. This patch adjust the watermark FIFO by increasing
the FIFO depth from 0x16(default) to 0x30 to address this issue.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Kiran Padwal <kiran.padwal21@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
In machines with multiple Silicon Image 3124 and/or 3132 cards, there is no
way to tell which card is the culprit when the sata_sil24 interrupt handler
gets a bad status.
Tested-by: Tim Small <tim@seoss.co.uk>
Signed-off-by: Tim Small <tim@seoss.co.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support of the Promise FastTrak TX8660 SATA HBA in ahci mode by
registering the board in the ahci_pci_tbl[].
Note: this HBA also provide a hardware RAID mode when activated in
BIOS but specific drivers from the manufacturer are required in this
case.
Signed-off-by: Romain Degez <romain.degez@gmail.com>
Tested-by: Romain Degez <romain.degez@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This adds support for the integrated AHCI-compliant Serial ATA
controller present on the NVIDIA Tegra124 system-on-chip.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Tegra124 SATA controller requires 4 clocks. Increase this constant
to be able to use them all.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
[linux-3.16-rc5/drivers/ata/pata_ep93xx.c:929]: (style) Checking if unsigned
variable 'irq' is less than zero.
Source code is
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
but
unsigned int irq;
$ fgrep platform_get_irq `find . -name \*.h -print`
./include/linux/platform_device.h:extern int platform_get_irq(struct
platform_device *, unsigned int);
Now using "int" type instead of "unsigned int" for "irq" variable.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80401
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
libata-eh.c should handle AMNF error condition (error byte bit 0,
usually code 0x01) in libata-eh.c along with UNC as a media error so
SCSI stack can handle it properly (translation code 0x01 is already
present in libata-scsi.c) but was never passed down due to lack of
handling in EH.
While using linux-based machine (AMD 6550M-based notebook, PCI IDs for the
controller are 1022:7801 subsys 1025:059d) and ddrescue to salvage data
from failing hard drive (WD7500BPVT 2.5" 750G SATA2), I've found that pure
AMNF 0x01 error code generates generic "device error" that is retried
several times by SCSI stack instead of "media error" that is passed up to
software.
So we may assume deprecated AMNF error code is surely not dead yet, and
it's better for it to be handled properly. As we may see it is used by
modern enough devices, and used properly: drive returned AMNF only when IDs
for track cannot be read completely due to dying head or positioning,
otherwise it returned UNC(orrectables).
Not handling it causes wrong generic error code ("device error") reporting
down the stack, can damage failing drives further because of excessive
retries, and slows salvaging down a lot. Also, there is handling code in
libata-scsi.c for 0x01 AMNF error already.
https://bugzilla.kernel.org/show_bug.cgi?id=80031
tj: Shortened $SUBJ and moved its content to the first paragraph.
Signed-off-by: Alexey Asemov <alex@alex-at.ru>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sata on fsl mpc8315e is broken after the commit 8a4aeec8d2
("libata/ahci: accommodate tag ordered controllers"). The reason is
that the ata controller on this SoC only implement a queue depth of
16. When issuing the commands in tag order, all the commands in tag
16 ~ 31 are mapped to tag 0 unconditionally and then causes the sata
malfunction. It makes no senses to use a 32 queue in software while
the hardware has less queue depth. So consider the queue depth
implemented by the hardware when requesting a command tag.
Fixes: 8a4aeec8d2 ("libata/ahci: accommodate tag ordered controllers")
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes the dma state machine lockup due to the processing
of IDENTIFY DEVICE PIO mode command. The X-Gene AHCI controller
has an errata in which it cannot clear the BSY bit after the PIO setup
FIS. The dma state machine enters CMFatalErrorUpdate state and locks
up. This patch also removes the dma restart workaround from the read_id
function as the read_id function is only called by libata layer for
ATA_INTERNAL commands. But for some cases eg: PORT MULTIPLIER
and udev, the framework will enumerate using SCSI commands and it will
not call read_id function.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The subsequent patch will make use of them.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Spread-spectrum doesn't work with Cubox-i hardware, so we have to
disable this feature. Add a DT property so that platforms can
indicate that this feature should not be enabled.
Having it as a negative property keeps existing DT files working.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Various SATA phy parameters are board specific, and therefore need to
be configured.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch removes support for s5pc100 ata because of no more support
S5PC100 SoC in mainline.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When the AHCI link is disabled, it can't be re-enabled except by
resetting the entire SoC. Rather than doing this silently print
some kernel messages to inform the user, along with how to avoid
this.
tj: Put a long printf format string on a single line.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
NCQ feature is unsupported on hisilicon sata controller, so disable
it. This version of IP is used by hip04 and hix5hd2 soc.
tj: "|=" was replaced with "=" for no reason. Restored "|=".
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Sigend-off-by: Tejun Heo <tj@kernel.org>
Doing suspend/resume on imx6q and imx53 boards with no SATA disk
attached will trigger the following warning.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 661 at drivers/ata/libahci.c:224 ahci_enable_ahci+0x74/0x8)
Modules linked in:
CPU: 0 PID: 661 Comm: sh Tainted: G W 3.15.0-rc5-next-20140521-000027
Backtrace:
[<80011c90>] (dump_backtrace) from [<80011e2c>] (show_stack+0x18/0x1c)
r6:803a22f4 r5:00000000 r4:00000000 r3:00000000
[<80011e14>] (show_stack) from [<80661e60>] (dump_stack+0x88/0xa4)
[<80661dd8>] (dump_stack) from [<80028fdc>] (warn_slowpath_common+0x70/0x94)
r5:00000009 r4:00000000
[<80028f6c>] (warn_slowpath_common) from [<80029024>] (warn_slowpath_null+0x24/)
r8:808f68c4 r7:00000000 r6:00000000 r5:00000000 r4:e0810004
[<80029000>] (warn_slowpath_null) from [<803a22f4>] (ahci_enable_ahci+0x74/0x80)
[<803a2280>] (ahci_enable_ahci) from [<803a2324>] (ahci_reset_controller+0x24/0)
r8:ddcd9410 r7:80351178 r6:ddcd9444 r5:dde8b850 r4:e0810000 r3:ddf35e90
[<803a2300>] (ahci_reset_controller) from [<803a2c68>] (ahci_platform_resume_ho)
r7:80351178 r6:ddcd9444 r5:dde8b850 r4:ddcd9410
[<803a2c30>] (ahci_platform_resume_host) from [<803a38f0>] (imx_ahci_resume+0x2)
r5:00000000 r4:ddcd9410
[<803a38c4>] (imx_ahci_resume) from [<803511ac>] (platform_pm_resume+0x34/0x54)
....
The reason is that the SATA controller has no working clock at this
point, and thus ahci_enable_ahci() fails to enable the controller. In
case that there is no SATA disk attached, the imx_sata_disable() gets
called in ahci_imx_error_handler(), and both sata_clk and sata_ref_clk
will be disabled there. Because all the imx_sata_enable() calls
afterward will return immediately due to imxpriv->no_device check, the
SATA controller working clock sata_clk will never get any chance to be
enabled again.
This is a regression caused by commit 90870d79d4 (ahci-imx: Port to
library-ised ahci_platform). Before the commit, only sata_ref_clk is
managed by the driver in enable/disable function. But after the commit,
all the clocks are enabled/disabled in a row by ahci platform helpers
ahci_platform_enable[disable]_clks. Since ahb_clk is a bus clock which
does not have gate at all, and i.MX low-power hardware module already
manages sata_clk across suspend/resume cycle, the only clock that needs
to be managed by software is sata_ref_clk.
So instead of using ahci_platform_enable[disable]_clks to manage all
the clocks in a row from imx_sata_enable[disable], we should manage
only sata_ref_clk in there.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Fixes: 90870d79d4 (ahci-imx: Port to library-ised ahci_platform)
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Instead of doing the check here, this should be handled
in the common AHCI platform code.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Loc Ho <lho@apm.com>
Cc: Tuan Phan <tphan@apm.com>
Cc: Suman Triphati <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The current platform AHCI driver does not set the dma_mask correctly
for 64-bit DMA capable AHCI controller. This patch checks the AHCI
capability bit and set the dma_mask and coherent_dma_mask accordingly.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ahci_platform_get_resources handles resource management for
platform AHCI drivers, including getting a possible PHY
from the device tree. Since not all drivers need a PHY, it
ignores -ENODEV and -ENOSYS from devm_get_phy. However, when
the PHY subsystem is mistakenly disabled, -ENOSYS can be
returned even when a PHY is needed.
This patch modifies the -ENOSYS case to check if a "phys"
device tree node exists. If it exists, then clearly the PHY
subsystem is mistakenly disabled and the driver cannot work,
ahci_platform_get_resources will fail and propagate the error.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Nothing too interesting - another ahci platform driver variant,
additional controller support, minor fixes and cleanups"
* 'for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Add Device ID for HighPoint RocketRaid 642L
ata: ep93xx: use dmaengine_prep_slave_sg api instead of internal callback
ahci: add PCI ID for Marvell 88SE91A0 SATA Controller
sata_fsl: remove check for CONFIG_MPC8315_DS
ahci: add support for Hisilicon sata
libahci_platform: add host_flags parameter in ahci_platform_init_host()
ata: ahci: append new hflag AHCI_HFLAG_NO_FBS
ata: use CONFIG_PM_SLEEP instead of CONFIG_PM where applicable in host drivers
ata: ahci_mvebu: new driver for Marvell Armada 380 AHCI interfaces
Documentation: dt-bindings: reformat and order list of ahci-platform compatibles
libata-sff: remove dead code
ata: SATL compliance for Inquiry Product Revision
pata_octeon_cf: use devm_kzalloc() to allocate cf_port
This device normally comes with a proprietary driver, using a web GUI
to configure RAID:
http://www.highpoint-tech.com/USA_new/series_rr600-download.htm
But thankfully it also works out of the box with the AHCI driver,
being just a Marvell 88SE9235.
Devices 640L, 644L, 644LS should also be supported but not tested here.
Signed-off-by: Jérôme Carretero <cJ-ko@zougloub.eu>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Queued trim only works for some users with MU05 firmware. Revert to
blacklisting all firmware versions.
Introduced by commit d121f7d0cb ("libata: Update queued trim blacklist
for M5x0 drives") which this effectively reverts, while retaining the
blacklisting of M550.
See
https://bugzilla.kernel.org/show_bug.cgi?id=71371
for reports of trouble with MU05 firmware.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
it is better to use generic api instead of calling an internal callback
like channel->device->device_prep_slave_sg().
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support for Marvell Technology Group Ltd. 88SE91A0 SATA 6Gb/s
Controller by adding its PCI ID.
Signed-off-by: Andreas Schrägle <ajs124.ajs124@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
A check for CONFIG_MPC8315_DS was added in v2.6.24. But the related
Kconfig symbol was never added to the tree. So the code behind this
check has effectively been dead for over six years. Remove it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Mostly device-specific fixes. The only thing which isn't is the fix
for zpodd oops-on-detach bug"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: imx: PLL clock needs 100us to settle down
ata: pata_at91 only works on sam9
libata: clean up ZPODD when a port is detached
ahci: imx: software workaround for phy reset issue in resume
ahci: imx: add namespace for register enums
ahci: disable DEVSLP for Intel Valleyview
The commit e783c51 (ahci: imx: software workaround for phy reset issue
in resume) calls imx_sata_phy_reset() to reset phy immediately after
SATA MPLL is enabled. It seems working fine mostly, but fails in some
case as below.
...
ahci-imx 2200000.sata: failed to reset phy: -110
ahci-imx: probe of 2200000.sata failed with error -110
After talking to the designer, we learnt that when enabling i.MX6Q SATA
MPLL, we need to wait 100us for it to settle down for safety. Add this
required delay to fix above failure.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The hip04 SoC of hisilicon has an AHCI compliant SATA controller,
and it is compliant with the ahci 1.3 and sata 3.0 specification.
There is a wrong bit in HOST_CAP of hip04 sata controller, which
enable unsupported feature of FBS, use AHCI_HFLAG_NO_FBS hflag to
disable it.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a dynamic host_flags argument to make ahci_platform_init_host more flexible,
then remove the AHCI_HFLAGS(...) argument from some driver's ata_port_info,
and pass that in as the new argument.
Cc: Hans de Geode <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Append AHCI_HFLAG_NO_FBS to force turning off FBS flag.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes host drivers to use CONFIG_PM_SLEEP instead of CONFIG_PM
where applicable. Benefits of this change:
* unused code is not being compiled in for CONFIG_PM=y, CONFIG_PM_SLEEP=n
and CONFIG_PM_RUNTIME=y configurations
* easier transition to use struct dev_pm_ops and SIMPLE_DEV_PM_OPS() in
the future
* more consistent code (there are host drivers which are using the correct
CONFIG_PM_SLEEP checks already)
The patch leaves the core libata code and ->port_[suspend,resume] support
in sata_[inic162x,nv,sil24].c alone for now.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The smc driver used by pata_at91 is at91sam9 specific, so building
this driver on another at91 platform results in this error:
ERROR: "sam9_smc_configure" [drivers/ata/pata_at91.ko] undefined!
ERROR: "sam9_smc_write_mode" [drivers/ata/pata_at91.ko] undefined!
ERROR: "sam9_smc_read_mode" [drivers/ata/pata_at91.ko] undefined!
This patch changes the Kconfig dependency to ensure it always works.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
When a ZPODD device is unbound via sysfs, the ACPI notify handler
is not removed. This causes panics as observed in Bug #74601. The
panic only happens when the wake happens from outside the kernel
(i.e. inserting a media or pressing a button). Add a loop to
ata_port_detach which loops through the port's devices and checks
if zpodd is enabled, if so call zpodd_exit.
Cc: stable@vger.kernel.org
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Marvell Armada 380 SoC includes two AHCI compatible
interfaces. However, like all DMA-capable Marvell interface, they
require special handling to configure MBus windows. Therefore, this
commit adds a new ahci_mvebu driver, which relies on the
libahci_platform.c code recently introduced.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
When suspending imx6q systems which have rootfs on SATA, the following
error will likely be seen in resume. The SATA link will fail to come
up, and it results in an unusable system across the suspend/resume
cycle.
$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
Freezing user space processes ... (elapsed 0.002 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
PM: Entering mem sleep
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
PM: suspend of devices complete after 61.914 msecs
PM: suspend devices took 0.070 seconds
PM: late suspend of devices complete after 4.906 msecs
PM: noirq suspend of devices complete after 4.521 msecs
Disabling non-boot CPUs ...
CPU1: shutdown
CPU2: shutdown
CPU3: shutdown
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
CPU1 is up
CPU2: Booted secondary processor
CPU2 is up
CPU3: Booted secondary processor
CPU3 is up
PM: noirq resume of devices complete after 10.486 msecs
PM: early resume of devices complete after 4.679 msecs
sd 0:0:0:0: [sda] Starting disk
PM: resume of devices complete after 22.674 msecs
PM: resume devices took 0.030 seconds
PM: Finishing wakeup.
Restarting tasks ... done.
$ ata1: SATA link down (SStatus 1 SControl 300)
ata1: SATA link down (SStatus 1 SControl 300)
ata1: limiting SATA link speed to 1.5 Gbps
ata1: SATA link down (SStatus 1 SControl 310)
ata1.00: disabled
ata1: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen t4
ata1: irq_stat 0x00000040, connection status changed
ata1: SError: { CommWake DevExch }
ata1: hard resetting link
sd 0:0:0:0: rejecting I/O to offline device
sd 0:0:0:0: killing request
sd 0:0:0:0: rejecting I/O to offline device
Aborting journal on device sda2-8.
sd 0:0:0:0: rejecting I/O to offline device
EXT4-fs warning (device sda2): ext4_end_bio:317: I/O error writing to inode 132577 (offset 0 size 0 starting block 26235)
Buffer I/O error on device sda2, logical block 10169
...
It's caused by a silicon issue that SATA phy does not get reset by
controller when coming back from LPM. The patch adds a software
workaround for this issue. It enforces a software reset on SATA phy
in imx_sata_enable() function, so that we can ensure SATA link will
come up properly in both power-on and resume.
The software reset is implemented by writing phy reset register through
the phy control register bus interface. Functions
imx_phy_reg_[addressing|write|read]() implement this bus interface, while
imx_sata_phy_reset() performs the actually reset operation.
Signed-off-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Update register enums a little bit to add proper namespace prefix, and
have the names match i.MX reference manual.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ever since v2.6.19 the code contains a check for CONFIG_NO_ATA_LEGACY.
But that macro has never been defined. Apparently no one ran into
problems on platforms that do not support compatibility mode. So remove
this code that has been dead for over seven years.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tejun Heo <tj@kernel.org>
The SCSI-to-ATA Translation standard says to use data words 25 and 26
unless they are spaces. For devices that use these words in the firmware
field, they are generally more useful anyway.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Dan updated tag allocation to accomodate devices which choke when tags
jump back and forth. Quite a few ahci MSI related fixes. A couple
config dependency fixes and other misc fixes"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata/ahci: accommodate tag ordered controllers
ahci: Do not receive interrupts sent by dummy ports
ahci: Use pci_enable_msi_exact() instead of pci_enable_msi_range()
ahci: Ensure "MSI Revert to Single Message" mode is not enforced
ahci: do not request irq for dummy port
pata_samsung_cf: fix ata_host_activate() failure handling
pata_arasan_cf: fix ata_host_activate() failure handling
ata: fix i.MX AHCI driver dependencies
pata_at91: fix ata_host_activate() failure handling
libata: Update queued trim blacklist for M5x0 drives
libata: make AHCI_XGENE depend on PHY_XGENE
On Intel Valleyview SoC, SATA device sleep is not reliable. When
DEVSLP is attempted on certain SSDs, port_devslp write would fail
and result in malfunction of AHCI controller. AHCI controller may
be not shown in PCI enumeration after reset. Complete power source
removal may be required to recover from this failure. So we blacklist
this device and override host device reported capabilities such that
device LPM will only attempt slumber but not DEVSLP.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The AHCI spec allows implementations to issue commands in tag order
rather than FIFO order:
5.3.2.12 P:SelectCmd
HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1)
or HBA selects the command to issue that has had the
PxCI bit set to '1' longer than any other command
pending to be issued.
The result is that commands posted sequentially (time-wise) may play out
of sequence when issued by hardware.
This behavior has likely been hidden by drives that arrange for commands
to complete in issue order. However, it appears recent drives (two from
different vendors that we have found so far) inflict out-of-order
completions as a matter of course. So, we need to take care to maintain
ordered submission, otherwise we risk triggering a drive to fall out of
sequential-io automation and back to random-io processing, which incurs
large latency and degrades throughput.
This issue was found in simple benchmarks where QD=2 seq-write
performance was 30-50% *greater* than QD=32 seq-write performance.
Tagging for -stable and making the change globally since it has a low
risk-to-reward ratio. Also, word is that recent versions of an unnamed
OS also does it this way now. So, drives in the field are already
experienced with this tag ordering scheme.
Cc: <stable@vger.kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ed Ciechanowski <ed.ciechanowski@intel.com>
Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In multiple MSI mode all AHCI ports (including dummy) get assigned
separate MSI vectors and (as result of execution
pci_enable_msi_exact() function) separate IRQ numbers, (mapped to the
MSI vectors).
Therefore, although interrupts from dummy ports are not desired they
are still enabled. We do not request IRQs for dummy ports, but that
only means we do not assign AHCI-specific ISRs to corresponding IRQ
numbers.
As result, dummy port interrupts still could come and traverse all the
way from the PCI device to the kernel, causing unnecessary overhead.
This update disables IRQs for dummy ports and prevents the described
issue.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: David Milburn <dmilburn@redhat.com>
Cc: linux-ide@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: 5ca72c4f7c ("AHCI: Support multiple MSIs")
The driver calls pci_enable_msi_range() function with the range of
[nvec..nvec] which is what pci_enable_msi_exact() function is for.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
The AHCI specification allows hardware to choose to revert to
single MSI mode when fewer messages are allocated than requested.
Yet, at least ICH10 chipset reverts to single MSI mode even when
enough messages are allocated in some cases (see below).
This update forces the driver to not rely on initialization of
multiple MSIs mode alone and always check if "MSI Revert to
Single Message" (MRSM) mode was enforced by the controller and
fallback to the single MSI mode in case it did.
That prevents a situation when the driver configured multiple
per-port IRQ handlers, but the controller sends all port's
interrupts to a single IRQ, which could easily screw up the
interrupt handling and lead to delays and possibly crashes.
The fix was tested on a 6-port controller that successfully
reverted to the single MSI mode:
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA
AHCI Controller (prog-if 01 [AHCI 1.0])
Subsystem: Super Micro Computer Inc Device 10a7
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 101
I/O ports at f110 [size=8]
I/O ports at f100 [size=4]
I/O ports at f0f0 [size=8]
I/O ports at f0e0 [size=4]
I/O ports at f020 [size=32]
Memory at fbf00000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
Capabilities: [70] Power Management version 3
Capabilities: [a8] SATA HBA v1.0
Capabilities: [b0] PCI Advanced Features
Kernel driver in use: ahci
With 6 ports just 8 MSI vectors should be enough, but the adapter
enforces the MRSM mode when less than 16 vectors are written to
the Multiple Messages Enable PCI register. I instigated MRSM mode
by forcing @nvec to 8 in ahci_init_interrupts().
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: linux-ide@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
