Make the ppc32 pcibios_alloc_controller take a device node to match
the ppc64 prototypes and have it set arch_data.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make the pci_controller struct use global_number for the PHB domain number
instead of index to match what ppc64 does and reuse its pci_domain_nr code.
Introduced a pci-common.c to handle shared code between ppc32 & ppc64.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are no in kernel users of any off these functions and some of
them were not even EXPORT_SYMBOL:
- pci_bus_io_base()
- pci_bus_io_base_phys()
- pci_bus_mem_base_phys()
- pci_resource_to_bus()
- phys_to_bus()
- pci_phys_to_bus()
- pci_bus_to_phys()
- pci_init_resource()
- resource_fixup()
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Moved bits need for ppc32 from asm-ppc/pci-bridge.h into
asm-powerpc/pci-bridge.h.
Removed ARCH=powerpc specific bits (and comments related to ARCH=ppc)
from asm-ppc/pci-bridge.h as its only used on ARCH=ppc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are times that we need to know which controller we are on to decide
how to exclude devices properly. We now pass the pci_controller that we
are going to use down to the pci_exclude_device function. This will
greatly simplify being able to exclude the PHBs in multiple controller
setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When CONFIG_PCI is disabled, the definitions for isa_io_base,
isa_mem_base and pci_dram_offset are entirely unused, but they
can result in link failure because they are defined in multiple
places.
The easiest fix is to just remove all these definitions.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Not all the world is an i386. Many architectures need 64-bit arguments to be
aligned in suitable pairs of registers, and the original
sys_sync_file_range(int, loff_t, loff_t, int) was therefore wasting an
argument register for padding after the first integer. Since we don't
normally have more than 6 arguments for system calls, that left no room for
the final argument on some architectures.
Fix this by introducing sys_sync_file_range2(int, int, loff_t, loff_t) which
all fits nicely. In fact, ARM already had that, but called it
sys_arm_sync_file_range. Move it to fs/sync.c and rename it, then implement
the needed compatibility routine. And stop the missing syscall check from
bitching about the absence of sys_sync_file_range() if we've implemented
sys_sync_file_range2() instead.
Tested on PPC32 and with 32-bit and 64-bit userspace on PPC64.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm-powerpc/processor.h declares, and arch/ppc/platforms/prep_setup.c
defines variables ucBoardRev, ucBoardRevMaj and ucBoardRevMin which
are used nowhere in the current kernel (neither in arch/ppc nor
arch/powerpc). This removes them.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently iSeries will recalibrate the cputime_factors in the first
settimeofday() call.
It seems the reason for doing this is to ensure a resaonable time delta after
time_init(). On current kernels (with udev), this call is made 40-60 seconds
into the boot process, by moving it to a late initcall it is called
approximately 5 seconds after time_init() is called. This is sufficient to
recalibrate the timebase.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add storage driver core support for the PS3.
PS3 storage devices are a special kind of PS3 system bus device.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Preallocate 256 KiB of bootmem memory for the PS3 FLASH ROM storage driver.
This can be disabled by passing `ps3flash=off' on the kernel command line.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Convert the ps3fb device from a platform device to a PS3 system bus device.
Fix the remove and shutdown methods to support kexec and to make ps3fb a
loadable module.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Make the PS3 ps3av driver a loadable module.
- Replace static data with kmalloc()'ed.
o Allocate struct ps3av dynamically, as it contains data used as vuart
receive/transmit buffers
o Move static recv_buf from ps3av_do_pkt() to struct ps3av
- Move ps3av_vuart_{read,write}() from drivers/ps3/ps3av_cmd.c to
drivers/ps3/ps3av.c and make them static as they're used in that file only.
- Make device a PS3 system-bus device.
- Update copyright formatting.
- Make two new routines ps3av_register_flip_ctl() and ps3av_flip_ctl() to
support late binding of the frame buffer flip control routine.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3 sys-manager updates to reflect the new PS3 unifed device support.
Fixups to the PS3 sys-manager driver to properly support sys_reboot().
- Add varable request_tag to struct ps3_sys_manager_header.
- Move ctrl_alt_del from PS3_SM_EVENT_POWER_RELEASED to
PS3_SM_EVENT_POWER_PRESSED.
- Make the PS3 sys-manager driver a loadable module.
- Add new file sys-manager-core.c.
- Add new struct ps3_sys_manager_ops for dynamic binding.
- Put data sent to device on stack.
- Add support for PS3_SM_SERVICE_ID_REQUEST_ERROR.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3 vuart updates to reflect the new PS3 unified device support.
- Move vuart devices to the PS3 system bus.
- Replace use of ps3_vuart_port_device with ps3_system_bus_device.
- Make the PS3 vuart bus driver a loadable module.
- Add remove() and shutdown() routines.
- Move ps3_vuart_work into ps3_vuart_port_priv.tx_list.
- Remove redundant spinlock ps3_vuart_work.lock.
- No longer free ps3_vuart_port_device.priv on shutdown.
- Cleanup Kconfig defs.
- Export symbols needed for modular port drivers.
- Arrange to use port numbers found in repository.
- Fix bugs in ps3_vuart_read_async() and polled reading
- Cleanup handling of shared interrupt with ps3_vuart_bus_interrupt_get()
and ps3_vuart_bus_interrupt_put()
- Add more comments to vuart.c.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rework the PS3 system bus to unify device support.
- DMA region sizes must be a power of two
- storage bus DMA updates:
- Small fixes for the PS3 DMA core:
o fix alignment bug
o kill superfluous test
o indentation
o spelling
o export ps3_dma_region_{create,free}()
- ps3_dma_region_init():
o Add `addr' and `len' parameters, so you can create a DMA region that
does not cover all memory (use `NULL' and `0' to cover all memory).
This is needed because there are not sufficient IOMMU resources to have
all DMA regions cover all memory.
o Uninline
- Added remove and shutdown routines to all drivers.
- Added loadable module support to all drivers.
- Added HV calls for iopte management (needed by sound driver).
Signed-off-by: MOKUNO Masakazu <mokuno@sm.sony.co.jp>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add support for HDMI RGB Full Range mode, which is available on system
software 1.80 or newer.
CC: Masashi Kimoto <Masashi_Kimoto@hq.scei.sony.co.jp>
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On Power machines supporting VRMA, Kexec/Kdump does not work.
VRMA (virtual real-mode area) means that accesses with IR/DR = 0
(i.e. the MMU "off") actually still go through the hash table,
using entries put there by the hypervisor.
This means that when we clear out the hash table on kexec, we need to
make sure these entries are left untouched.
This also adds plpar_pte_read_raw() on the lines of
plpar_pte_remove_raw().
Signed-off-by : Sachin Sant <sachinp@in.ibm.com>
Signed-off-by : Mohan Kumar M <mohan@in.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For POWERPC, stolen time accounts for cycles lost to the hypervisor or
PURR cycles attributed to the other SMT thread. Hence, when a PURR is
available, we should still calculate stolen time, irrespective of being
virtualised.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds irq_create_direct_mapping(). This routine is
an alternative to irq_create_mapping(), for irq controllers that
can use linux virq numbers directly as hardware numbers.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Uninline virq_to_hw and export it so modules can use it. The alternative
would be to export the irq_map array instead, but it's an infrequently
called function, and keeping the array unexported seems considerably
cleaner.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some changes done a while ago to avoid pounding on ptep_set_access_flags and
update_mmu_cache in some race situations break sun4c which requires
update_mmu_cache() to always be called on minor faults.
This patch reworks ptep_set_access_flags() semantics, implementations and
callers so that it's now responsible for returning whether an update is
necessary or not (basically whether the PTE actually changed). This allow
fixing the sparc implementation to always return 1 on sun4c.
[akpm@linux-foundation.org: fixes, cleanups]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: David Miller <davem@davemloft.net>
Cc: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Acked-by: William Lee Irwin III <wli@holomorphy.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the powerpc kernel has a 64-bit only feature,
COHERENT_ICACHE used for those CPUS which maintain icache/dcache
coherency in hardware (POWER5, essentially). It also has a feature,
SPLIT_ID_CACHE, which is used on CPUs which have separate i and
d-caches, which is to say everything except 601 and Freescale E200.
In nearly all the places we check the SPLIT_ID_CACHE, what we actually
care about is whether the i and d-caches are coherent (which they will
be, trivially, if they're the same cache).
This tries to clarify the situation a little. The COHERENT_ICACHE
feature becomes availble on 32-bit and is set for all CPUs where i and
d-cache are effectively coherent, whether this is due to special logic
(POWER5) or because they're unified. We check this, instead of
SPLIT_ID_CACHE nearly everywhere.
The SPLIT_ID_CACHE feature itself is replaced by a UNIFIED_ID_CACHE
feature with reversed sense, set only on 601 and Freescale E200. In
the two places (one Freescale BookE specific) where we really care
whether it's a unified cache, not whether they're coherent, we check
this feature. The CPUs with unified cache are so few, we could
consider replacing this feature bit with explicit checks against the
PVR.
This will make unifying the 32-bit and 64-bit cache flush code a
little more straightforward.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Using typedefs to rename structure types if frowned on by CodingStyle.
However, we do so for the hash PTE structure on both ppc32 (where it's
called "PTE") and ppc64 (where it's called "hpte_t"). On ppc32 we
also have such a typedef for the BATs ("BAT").
This removes this unhelpful use of typedefs, in the process
bringing ppc32 and ppc64 closer together, by using the name "struct
hash_pte" in both cases.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This factors some things defined in both pgtable-ppc32.h and
pgtable-ppc64.h into the common part of asm-powerpc/pgtable.h. These
are all things which have essentially identical definitions, and which
by their nature are very unlikely ever to need different definitions
in the two cases.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
APUS (the Amiga Power-Up System) is not supported under arch/powerpc
and it's unlikely it ever will be. Therefore, this patch removes the
fragments of APUS support code from arch/powerpc which have been
copied from arch/ppc.
A few APUS references are left in asm-powerpc in .h files which are
still used from arch/ppc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These old-fashioned IO mapping functions no longer have any callers in
code which remains relevant on arch/powerpc. Therefore, this removes
them from arch/powerpc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
arch/powerpc still relies on asm-ppc/mmu.h for most 32-bit MMU types.
This is another step towards fixing this. It takes the portions
of asm-ppc/mmu.h related to the "classic" 32-bit hash page table MMU
which are still relevant in arch/powerpc and puts them in a new
asm-powerpc/mmu-hash32.h, included when appropriate from
asm-powerpc/mmu.h.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A Power6 can give up CPU cycles on a dedicated CPU (as opposed to a
shared CPU) to other shared processors if the administrator asks for it
(via the HMC).
This enables that to work properly on P6.
This just involves setting a bit in the CAS structure as well as the
VPA. To donate cycles, a CPU has to have all SMT threads idle and
have the donate bit set in the VPA. Then call H_CEDE.
The reason why shared processors just aren't used is because dedicated
CPUs are guaranteed an actual processor, yet the system is still able to
increase the capacity of the shared CPU pool.
Also rename the VPA's cpuctls_task_attrs field to a more accurate name.
Signed-off-by: Jake Moilanen <moilanen@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
sys_sigaltstack is the same on 32bit and 64 and we can consolidate it
to signal.c. The only difference is that the 32bit code uses ints
for the unused register paramaters and 64bit unsigned long. I've
changed it to unsigned long because it's the same width on 32bit.
(I also wonder who came up with this awkward calling convention.. :))
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This folds back the ptrace-common.h bits back into ptrace.c and removes
that file. The FSL SPE bits from ptrace-ppc32.h are folded back in as
well.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc ptrace interface is dodgy at best. We have defined our
"own" versions of GETREGS/SETREGS/GETFPREGS/SETFPREGS that strangely
take arguments in reverse order from other archs (in addition to having
different request numbers) and have subtle issue, like not accessing
all of the registers in their respective categories.
This patch moves the implementation of those to a separate function
in order to facilitate their deprecation in the future, and provides
new ptrace requests that mirror the x86 and sparc ones and use the
same numbers:
PTRACE_GETREGS : returns an entire pt_regs (the whole thing,
not only the 32 GPRs, though that doesn't
include the FPRs etc... There's a compat version
for 32 bits that returns a 32 bits compatible
pt_regs (44 uints)
PTRACE_SETREGS : sets an entire pt_regs (the whole thing,
not only the 32 GPRs, though that doesn't
include the FPRs etc... Some registers cannot be
written to and will just be dropped, this is the
same as with POKEUSR, that is anything above MQ
on 32 bits and CCR on 64 bits. There is a compat
version as well.
PTRACE_GETFPREGS : returns all the FP registers -including- the FPSCR
that is 33 doubles (regardless of 32/64 bits)
PTRACE_SETFPREGS : sets all the FP registers -including- the FPSCR
that is 33 doubles (regardless of 32/64 bits)
And two that only exist on 64 bits kernels:
PTRACE_GETREGS64 : Same as PTRACE_GETREGS, except there is no compat
function, a 32 bits process will obtain the full 64
bits registers
PTRACE_SETREGS64 : Same as PTRACE_SETREGS, except there is no compat
function, a 32 bits process will set the full 64
bits registers
The two later ones makes things easier to have a 32 bits debugger on a
64 bits program (or on a 32 bits program that uses the full 64 bits of
the GPRs, which is possible though has issues that will be fixed in a
later patch).
Finally, while at it, the patch removes a whole bunch of code duplication
between ptrace32.c and ptrace.c, in large part by having the former call
into the later for all requests that don't need any special "compat"
treatment.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This rewrites pretty much from scratch the handling of MMIO and PIO
space allocations on powerpc64. The main goals are:
- Get rid of imalloc and use more common code where possible
- Simplify the current mess so that PIO space is allocated and
mapped in a single place for PCI bridges
- Handle allocation constraints of PIO for all bridges including
hot plugged ones within the 2GB space reserved for IO ports,
so that devices on hotplugged busses will now work with drivers
that assume IO ports fit in an int.
- Cleanup and separate tracking of the ISA space in the reserved
low 64K of IO space. No ISA -> Nothing mapped there.
I booted a cell blade with IDE on PIO and MMIO and a dual G5 so
far, that's it :-)
With this patch, all allocations are done using the code in
mm/vmalloc.c, though we use the low level __get_vm_area with
explicit start/stop constraints in order to manage separate
areas for vmalloc/vmap, ioremap, and PCI IOs.
This greatly simplifies a lot of things, as you can see in the
diffstat of that patch :-)
A new pair of functions pcibios_map/unmap_io_space() now replace
all of the previous code that used to manipulate PCI IOs space.
The allocation is done at mapping time, which is now called from
scan_phb's, just before the devices are probed (instead of after,
which is by itself a bug fix). The only other caller is the PCI
hotplug code for hot adding PCI-PCI bridges (slots).
imalloc is gone, as is the "sub-allocation" thing, but I do beleive
that hotplug should still work in the sense that the space allocation
is always done by the PHB, but if you unmap a child bus of this PHB
(which seems to be possible), then the code should properly tear
down all the HPTE mappings for that area of the PHB allocated IO space.
I now always reserve the first 64K of IO space for the bridge with
the ISA bus on it. I have moved the code for tracking ISA in a separate
file which should also make it smarter if we ever are capable of
hot unplugging or re-plugging an ISA bridge.
This should have a side effect on platforms like powermac where VGA IOs
will no longer work. This is done on purpose though as they would have
worked semi-randomly before. The idea at this point is to isolate drivers
that might need to access those and fix them by providing a proper
function to obtain an offset to the legacy IOs of a given bus.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Track and report the number of times we read an all-1s value (0xff,
0xffff or 0xffffffff) from each device which is valid data, not
indicating EEH isolation.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
arch/powerpc/platforms/pseries/eeh.c | 5 +++++
arch/powerpc/platforms/pseries/eeh_sysfs.c | 3 +++
include/asm-powerpc/pci-bridge.h | 1 +
3 files changed, 9 insertions(+)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Use the correct CONFIG_ option to mark off the EEH bits.
Move the EEH bits to the bottom of the struct.
The config_space array is used by EEH only; it does not
need to be part of the struct for non-pseries machines.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
----
Revised patch, per commments from Michael Ellerman.
include/asm-powerpc/pci-bridge.h | 16 +++++++++-------
1 file changed, 9 insertions(+), 7 deletions(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reserve two TIF flags for perfmon2 and shift them into the low 16 bits
so we can use single assembly instructions to create constants based off
them.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
pte_alloc_one() is expected to return NULL if out of memory.
But it returns virt_to_page(NULL), which is not NULL.
This fixes it.
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I think we have a subtle race on ppc64 with the tlb batching. The
common code expects tlb_flush() to actually flush any pending TLB
batch. It does that because it delays all page freeing until after
tlb_flush() is called, in order to ensure no stale reference to
those pages exist in any TLB, thus causing potential access to
the freed pages.
However, our tlb_flush only triggers the RCU for freeing page
table pages, it does not currently trigger a flush of a pending
TLB/hash batch, which is, I think, an error. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are no actual implementations of fixup_bigphys_addr() in
arch/powerpc, and with a 64-bit aware ioremap() and so forth, it
should no longer be necessary. This patch removes the last dregs of
fixup_bigphys_addr() from arch/powerpc.
In fact, the only reason this hasn't caused link errors already is
that nobody must have tried using one of the small number of drivers
using io_remap_pfn_range() on one of the small number of platforms
which are 32-bit but define CONFIG_PHYS_64BIT. Nonetheless this fixes
a bug, and should go into 2.6.22.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove CPU_FTR_NEED_COHERENT for MPC7448 (and single-core MPC86xx).
This prevents needlessly setting M=1 when not SMP.
Signed-off-by: James.Yang <James.Yang@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change several headers in include/asm-powerpc that currently use some variation
of ASM_PPC to use ASM_POWERPC instead.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch renames the raw hard_irq_{enable,disable} into
__hard_irq_{enable,disable} and introduces a higher level hard_irq_disable()
function that can be used by any code to enforce that IRQs are fully disabled,
not only lazy disabled.
The difference with the __ versions is that it will update some per-processor
fields so that the kernel keeps track and properly re-enables them in the next
local_irq_disable();
This prepares powerpc for my next patch that introduces hard_irq_disable()
generically.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These files are almost all the same.
This patch could be made even simpler if we don't mind POLLREMOVE turning
up in a few architectures that didn't have it previously (which should be
OK as POLLREMOVE is not used anywhere in the current tree).
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the necessary support to hpte_decode() to handle 1TB
segments and 16GB pages, and removes an uninitialized value
warning on avpn.
We don't have any code to generate HPTEs for 1TB segments or 16GB
pages yet, so this is mostly for completeness, and to fix the
warning.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fix a PS3 build error when CONFIG_PS3_SYS_MANAGER=n.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The rheap allocation functions return a pointer, but the actual value is based
on how the heap was initialized, and so it can be anything, e.g. an offset
into a buffer. A ulong is a better representation of the value returned by
the allocation functions.
This patch changes all of the relevant rheap functions to use a unsigned long
integers instead of a pointer. In case of an error, the value returned is
a negative error code that has been cast to an unsigned long. The caller can
use the IS_ERR_VALUE() macro to check for this.
All code which calls the rheap functions is updated accordingly. Macros
IS_MURAM_ERR() and IS_DPERR(), have been deleted in favor of IS_ERR_VALUE().
Also added error checking to rh_attach_region().
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch moves a copy of reg_booke.h to include/asm-powerpc and fixes
up the ifdef protection.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Further fixes for the removal of 4level-fixup hack from ppc32
[POWERPC] EEH: log all PCI-X and PCI-E AER registers
[POWERPC] EEH: capture and log pci state on error
[POWERPC] EEH: Split up long error msg
[POWERPC] EEH: log error only after driver notification.
[POWERPC] fsl_soc: Make mac_addr const in fs_enet_of_init().
[POWERPC] Don't use SLAB/SLUB for PTE pages
[POWERPC] Spufs support for 64K LS mappings on 4K kernels
[POWERPC] Add ability to 4K kernel to hash in 64K pages
[POWERPC] Introduce address space "slices"
[POWERPC] Small fixes & cleanups in segment page size demotion
[POWERPC] iSeries: Make HVC_ISERIES the default
[POWERPC] iSeries: suppress build warning in lparmap.c
[POWERPC] Mark pages that don't exist as nosave
[POWERPC] swsusp: Introduce register_nosave_region_late
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
sound: convert "sound" subdirectory to UTF-8
MAINTAINERS: Add cxacru website/mailing list
include files: convert "include" subdirectory to UTF-8
general: convert "kernel" subdirectory to UTF-8
documentation: convert the Documentation directory to UTF-8
Convert the toplevel files CREDITS and MAINTAINERS to UTF-8.
remove broken URLs from net drivers' output
Magic number prefix consistency change to Documentation/magic-number.txt
trivial: s/i_sem /i_mutex/
fix file specification in comments
drivers/base/platform.c: fix small typo in doc
misc doc and kconfig typos
Remove obsolete fat_cvf help text
Fix occurrences of "the the "
Fix minor typoes in kernel/module.c
Kconfig: Remove reference to external mqueue library
Kconfig: A couple of grammatical fixes in arch/i386/Kconfig
Correct comments in genrtc.c to refer to correct /proc file.
Fix more "deprecated" spellos.
Fix "deprecated" typoes.
...
Fix trivial comment conflict in kernel/relay.c.
With the advent of kdump, the assumption that the boot CPU when booting an UP
kernel is always the CPU with a particular hardware ID (often 0) (usually
referred to as BSP on some architectures) is not valid anymore. The reason
being that the dump capture kernel boots on the crashed CPU (the CPU that
invoked crash_kexec), which may be or may not be that particular CPU.
Move definition of hard_smp_processor_id for the UP case to
architecture-specific code ("asm/smp.h") where it belongs, so that each
architecture can provide its own implementation.
Signed-off-by: Fernando Luis Vazquez Cao <fernando@oss.ntt.co.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Acked-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The SLUB allocator relies on struct page fields first_page and slab,
overwritten by ptl when SPLIT_PTLOCK: so the SLUB allocator cannot then
be used for the lowest level of pagetable pages. This was obstructing
SLUB on PowerPC, which uses kmem_caches for its pagetables. So convert
its pte level to use normal gfp pages (whereas pmd, pud and 64k-page pgd
want partpages, so continue to use kmem_caches for pmd, pud and pgd).
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds an option to spufs when the kernel is configured for
4K page to give it the ability to use 64K pages for SPE local store
mappings.
Currently, we are optimistic and try order 4 allocations when creating
contexts. If that fails, the code will fallback to 4K automatically.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds the ability for a kernel compiled with 4K page size
to have special slices containing 64K pages and hash the right type
of hash PTEs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The basic issue is to be able to do what hugetlbfs does but with
different page sizes for some other special filesystems; more
specifically, my need is:
- Huge pages
- SPE local store mappings using 64K pages on a 4K base page size
kernel on Cell
- Some special 4K segments in 64K-page kernels for mapping a dodgy
type of powerpc-specific infiniband hardware that requires 4K MMU
mappings for various reasons I won't explain here.
The main issues are:
- To maintain/keep track of the page size per "segment" (as we can
only have one page size per segment on powerpc, which are 256MB
divisions of the address space).
- To make sure special mappings stay within their allotted
"segments" (including MAP_FIXED crap)
- To make sure everybody else doesn't mmap/brk/grow_stack into a
"segment" that is used for a special mapping
Some of the necessary mechanisms to handle that were present in the
hugetlbfs code, but mostly in ways not suitable for anything else.
The patch relies on some changes to the generic get_unmapped_area()
that just got merged. It still hijacks hugetlb callbacks here or
there as the generic code hasn't been entirely cleaned up yet but
that shouldn't be a problem.
So what is a slice ? Well, I re-used the mechanism used formerly by our
hugetlbfs implementation which divides the address space in
"meta-segments" which I called "slices". The division is done using
256MB slices below 4G, and 1T slices above. Thus the address space is
divided currently into 16 "low" slices and 16 "high" slices. (Special
case: high slice 0 is the area between 4G and 1T).
Doing so simplifies significantly the tracking of segments and avoids
having to keep track of all the 256MB segments in the address space.
While I used the "concepts" of hugetlbfs, I mostly re-implemented
everything in a more generic way and "ported" hugetlbfs to it.
Slices can have an associated page size, which is encoded in the mmu
context and used by the SLB miss handler to set the segment sizes. The
hash code currently doesn't care, it has a specific check for hugepages,
though I might add a mechanism to provide per-slice hash mapping
functions in the future.
The slice code provide a pair of "generic" get_unmapped_area() (bottomup
and topdown) functions that should work with any slice size. There is
some trickiness here so I would appreciate people to have a look at the
implementation of these and let me know if I got something wrong.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
tas() has no users, so get rid of it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: <linux-arch@vger.kernel.org>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
atomic_add_unless as inline. Remove system.h atomic.h circular dependency.
I agree (with Andi Kleen) this typeof is not needed and more error
prone. All the original atomic.h code that uses cmpxchg (which includes
the atomic_add_unless) uses defines instead of inline functions,
probably to circumvent a circular dependency between system.h and
atomic.h on powerpc (which my patch addresses). Therefore, it makes
sense to use inline functions that will provide type checking.
atomic_add_unless as inline. Remove system.h atomic.h circular dependency.
Digging into the FRV architecture shows me that it is also affected by
such a circular dependency. Here is the diff applying this against the
rest of my atomic.h patches.
It applies over the atomic.h standardization patches.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the size of the per-cpu region reserved to save crash notes is
set by the per-architecture value MAX_NOTE_BYTES. Which in turn is
currently set to 1024 on all supported architectures.
While testing ia64 I recently discovered that this value is in fact too
small. The particular setup I was using actually needs 1172 bytes. This
lead to very tedious failure mode where the tail of one elf note would
overwrite the head of another if they ended up being alocated sequentially
by kmalloc, which was often the case.
It seems to me that a far better approach is to caclculate the size that
the area needs to be. This patch does just that.
If a simpler stop-gap patch for ia64 to be squeezed into 2.6.21(.X) is
needed then this should be as easy as making MAX_NOTE_BYTES larger in
arch/asm-ia64/kexec.h. Perhaps 2048 would be a good choice. However, I
think that the approach in this patch is a much more robust idea.
Acked-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently a parport_driver can't get a handle on the device node for the
underlying parport (PNPACPI, PCI, etc). That prevents correct placement of
sysfs child nodes, which can affect things like power management.
This patch adds a field to "struct parport" pointing to that device node, and
updates non-legacy port drivers to initialize that device pointer. That field
replaces the analagous PCI-only support in parport_pc.
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch moves the die notifier handling to common code. Previous
various architectures had exactly the same code for it. Note that the new
code is compiled unconditionally, this should be understood as an appel to
the other architecture maintainer to implement support for it aswell (aka
sprinkling a notify_die or two in the proper place)
arm had a notifiy_die that did something totally different, I renamed it to
arm_notify_die as part of the patch and made it static to the file it's
declared and used at. avr32 used to pass slightly less information through
this interface and I brought it into line with the other architectures.
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix vmalloc_sync_all bustage]
[bryan.wu@analog.com: fix vmalloc_sync_all in nommu]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-arch@vger.kernel.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds support for early serial debugging via the built in
port on IBM/AMCC PowerPC 44x CPUs. It uses a bolted TLB entry in
address space 1 for the UART's mapping, allowing robust debugging both
before and after the initialization of the MMU.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To support MSI on MPIC we need a way to reserve and allocate hardware irq
numbers, this patch implements an allocator for that purpose.
New firmware platforms must define a "msi-available-ranges" property on their
MPIC node for MSI to work. For U3/U4 we do a best-guess setup.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This provides the architecture specific hooks to support MSI on
powerpc. We implement the newly added arch_setup_msi_irqs() and
arch_teardown_msi_irqs(), and then delegate to ppc_md routines.
Platforms that don't implement MSI will leave the ppc_md calls blank,
arch_msi_check_device() will detect this and return ENOSYS. Drivers
should detect this error and continue to use LSI.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rip out the existing powerpc msi stubs. These were the start of an
implementation based on ppc_md calls, but were never used in mainline.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For 32-bit systems, powerpc still relies on the 4level-fixup.h hack,
to pretend that the generic pagetable handling stuff is 3-levels
rather than 4. This patch removes this, instead using the newer
pgtable-nopmd.h to handle the elision of both the pud and pmd
pagetable levels (ppc32 pagetables are actually 2 levels).
This removes a little extraneous code, and makes it more easily
compared to the 64-bit pagetable code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Generalize tsi108_setup_pci to take the config space physical address and
primary bus designator as a parameter.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a phy_type field to the tsi108 ethernet structures to indicate which PHY
is used on a board. This is derived from the "compatible" property in the
ethernet-phy node of the device tree. The default remains the MV88E PHY.
Also, convert the setup code to use of_get_mac_address instead of hard coding
a lookup for the "address" property in the ethernet node.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add a header file for the common PCI routines used for the TSI bridge
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement deep-sleep on MPC52xx.
SDRAM is put into self-refresh with help of SRAM code
(alternatives would be code in FLASH, I-cache).
Interrupt code must also not be in SDRAM, so put it
in I-cache.
MPC52xx core is static, so contents will remain intact even
with clocks turned off.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Apparently other parts of the kernel need to know the
modalias internally (like the sysfs code in macintosh driver).
To avoid consistency issues, we export this code and use it
everywhere it's needed rather than repeat it ...
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
32-bit powerpc uses a PTE_FMT macro to handle printk() formatting of
PTE entries (which can vary in type and size). Apparently there was a
good reason for it once, but with current compilers it's simpler just
to workaround the variation with a cast in the printk() itself
(there's only one use).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements save and restore hooks for IOMMUs and implements
it the DART iommu.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This allows "hotplugging" of CPUs on G5 machines. CPUs that are
disabled are put into an idle loop with the decrementer frequency set
to minimum. To wake them up again we kick them just like when bringing
them up. To stop those CPUs from messing with any global state we stop
them from entering the timer interrupt.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds mpic to the system devices and implements suspend
and resume for them. This is necessary to get interrupts for
modules back to where they were before a suspend to disk.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (231 commits)
[PATCH] i386: Don't delete cpu_devs data to identify different x86 types in late_initcall
[PATCH] i386: type may be unused
[PATCH] i386: Some additional chipset register values validation.
[PATCH] i386: Add missing !X86_PAE dependincy to the 2G/2G split.
[PATCH] x86-64: Don't exclude asm-offsets.c in Documentation/dontdiff
[PATCH] i386: avoid redundant preempt_disable in __unlazy_fpu
[PATCH] i386: white space fixes in i387.h
[PATCH] i386: Drop noisy e820 debugging printks
[PATCH] x86-64: Fix allnoconfig error in genapic_flat.c
[PATCH] x86-64: Shut up warnings for vfat compat ioctls on other file systems
[PATCH] x86-64: Share identical video.S between i386 and x86-64
[PATCH] x86-64: Remove CONFIG_REORDER
[PATCH] x86-64: Print type and size correctly for unknown compat ioctls
[PATCH] i386: Remove copy_*_user BUG_ONs for (size < 0)
[PATCH] i386: Little cleanups in smpboot.c
[PATCH] x86-64: Don't enable NUMA for a single node in K8 NUMA scanning
[PATCH] x86: Use RDTSCP for synchronous get_cycles if possible
[PATCH] i386: Add X86_FEATURE_RDTSCP
[PATCH] i386: Implement X86_FEATURE_SYNC_RDTSC on i386
[PATCH] i386: Implement alternative_io for i386
...
Fix up trivial conflict in include/linux/highmem.h manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3av:
- Move the definition of struct ps3av to ps3av.c, as it's locally used only.
- Kill ps3av.sem, use the existing ps3av.mutex instead.
- Make the 512-byte buffer in ps3av_do_pkt() static to reduce stack usage.
Its use is protected by a semaphore anyway.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ps3av: Replace the kernel_thread and the ping pong semaphores by a singlethread
workqueue and a completion.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add hooks to allow a paravirt implementation to track the lifetime of
an mm. Paravirtualization requires three hooks, but only two are
needed in common code. They are:
arch_dup_mmap, which is called when a new mmap is created at fork
arch_exit_mmap, which is called when the last process reference to an
mm is dropped, which typically happens on exit and exec.
The third hook is activate_mm, which is called from the arch-specific
activate_mm() macro/function, and so doesn't need stub versions for
other architectures. It's called when an mm is first used.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: linux-arch@vger.kernel.org
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Call the kprobes pagefault handler directly instead of going through
the complex notifier chain.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
When data symbols are not present in kernel image, user needs to add
dot(".") before function name explicitly, that he wants to probe in kprobe
module on ppc64.
for ex:-
When data symbols are missing on ppc64,
====================
[root@llm27lp1 ~]# cat /proc/kallsyms | grep do_fork
c00000000006283c T .do_fork
==============================
User needs add "." to "do_fork"
kp.symbol_name = ".do_fork";
============================
This makes kprobe modules unportable. This fixes the problem.
Signed-off-by: Srinivasa Ds <srinivasa@in.ibm.com>
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fixups for the ps3 interrupt routines to support all HV device
in a generic way.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In commit 0fba3a1f39 (a very long time ago,
May 2006), I fixed a bug that caused powermacs to crash when you tried
entering standby/mem suspend states.
As I'm now getting more familiar with the suspend code I notice a few
more things:
1. we previously misunderstood what pm_ops is for, it isn't supposed to be
for doing platform dependent suspend/resume stuff that needs to be done
for suspend to disk (as we currently try to use it!), it is instead for
entering platform dependent suspend states ("standby", "mem").
2. due to the first point, we never properly save FPU and altivec states
when suspending to disk. It probably hasn't hurt yet because the process
that writes the "disk" to /sys/power/state uses neither and its context
is used.
This patch addresses these points as follows:
1. remove all pm_ops from powermac, powermac suspend to ram isn't currently
usable via /sys/power/state but is done via the PMU instead.
2. move the code responsible for storing FPU/altivec state into
save_processor_state and the set_context() call to restore_processor_state.
3. add a call to kernel_enable_spe()
It may look like there is some code removal missing but that is
actually because the new suspend.h file overrides the ppc/suspend.h
one which was previously used.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, all 32-bit powerpc platforms use asm-ppc/pgtable.h and
asm-ppc/pgalloc.h, even when otherwise compiled with ARCH=powerpc.
Those asm-ppc files are a fairly nasty tangle of #ifdefs including a
bunch of things which shouldn't be necessary any more in arch/powerpc.
Cleaning up that mess is going to take a while, but this patch is a
first step. It separates the asm-powerpc/pg{alloc,table}.h into 64
bit and 32 bit versions in asm-powerpc, which the basic .h files in
asm-powerpc select based on config. We make a few tiny tweaks to the
innards of the files along the way, making the outermost ifdefs
(double-inclusion protection and __KERNEL__) a little cleaner, and
#including asm-generic/pgtable.h from the top-level
asm-powerpc/pgtable.h (since both the old 32-bit and 64-bit versions
ended with such an #include).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since we don't have it active by default, the STRICT_MM_TYPECHECKS
option has bitrotted again. This patch fixes a couple of simple build
fixes if the option is selected. First, pud_t mustn't be defined in
page.h on 32-bit systems, because it conflicts with the version in the
generic pud-folding code. Second, pci_32.c is missing a __pgprot()
wrapper call. Third, a couple of PS3 files use constants of type
pgprot_t when they need the raw values, we add pgprot_val() calls to
fix this.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch takes the definitions for the PPC44x MMU (a software loaded
TLB) from asm-ppc/mmu.h, cleans them up of things no longer necessary
in arch/powerpc and puts them in a new asm-powerpc/mmu_44x.h file. It
also substantially simplifies arch/powerpc/mm/44x_mmu.c and makes a
couple of small fixes necessary for the 44x MMU code to build and work
properly in arch/powerpc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is no big reason to have that function inlined.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the powerpc architecture, of_irq_to_resource, currently sitting in
prom.h, needs irq_of_parse_and_map and NO_IRQ from asm-powerpc/irq.h.
The solution suggested by Benjamin Herrenschmidt is to move it to
arch/powerpc/kernel/prom_parse.c.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch makes sure that a caller of pmac_call_feature() won't try
to call into ppc_md.feature_call of another platform, which might
happen if some powermac drivers are loaded on non-powermac machines.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch puts enable_kernel_spe into <asm-powerpc/system.h> along with
enable_kernel_altivec etc.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Transmit on Demand: Fix spelling in config option, and make it actually enable TOD.
Signed-off-by: Michael Reiss <michael.f.reiss@freescale.com>
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (67 commits)
[SCSI] SUNESP: Complete driver rewrite to version 2.0
[SPARC64]: Convert PCI over to generic struct iommu/strbuf.
[SPARC]: device_node name constification fallout
[SPARC64]: Convert SBUS over to generic iommu/strbuf structs.
[SPARC64]: Add generic iommu and strbuf structs to iommu.h
[SPARC64]: Consolidate {sbus,pci}_iommu_arena.
[SPARC]: Make device_node name and type const
[SPARC64]: constify some paramaters of OF routines
[TIGON3]: of_get_property() returns const.
[SPARC64]: Fix PCI rework to adhere to of_get_property() const return.
[SPARC64]: Document and fix calculation of pages_avail.
[SPARC64]: Make sure pbm->prom_node is setup easly enough in psycho.c
[SPARC64]: Use bootmem_bootmap_pages() in choose_bootmap_pfn().
[SPARC64]: Add proper header file extern for cmdline_memory_size.
[SPARC64]: Kill sparc_ultra_dump_{i,d}tlb()
[SPARC64]: Use DECLARE_BITMAP and BITS_TO_LONGS in mm/init.c
[SPARC64]: Give move verbose show_mem() output just like i386.
[SPARC64]: Mark show_mem() printk's with KERN_INFO.
[SPARC64]: Kill kvaddr_to_phys() and friends.
[SPARC64]: Privatize sun4u_get_pte() and fix name.
...
check_legacy_ioport makes only sense on PREP, CHRP and pSeries.
They may have an isa node with PS/2, parport, floppy and serial ports.
Remove the check_legacy_ioport call from ppc_md, it's not needed
anymore. Hardware capabilities come from the device-tree.
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently asm-powerpc/mmu.h has definitions for the 64-bit hash based
MMU. If CONFIG_PPC64 is not set, it instead includes asm-ppc/mmu.h
which contains a particularly horrible mess of #ifdefs giving the
definitions for all the various 32-bit MMUs.
It would be nice to have the low level definitions for each MMU type
neatly in their own separate files. It would also be good to wean
arch/powerpc off dependence on the old asm-ppc/mmu.h.
This patch makes a start on such a cleanup by moving the definitions
for the 64-bit hash MMU to their own file, asm-powerpc/mmu_hash64.h.
Definitions for the other MMUs still all come from asm-ppc/mmu.h,
however each MMU type can now be one-by-one moved over to their own
file, in the process cleaning them up stripping them of cruft no
longer necessary in arch/powerpc.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that network timestamps use ktime_t infrastructure, we can add a new
SOL_SOCKET sockopt SO_TIMESTAMPNS.
This command is similar to SO_TIMESTAMP, but permits transmission of
a 'timespec struct' instead of a 'timeval struct' control message.
(nanosecond resolution instead of microsecond)
Control message is labelled SCM_TIMESTAMPNS instead of SCM_TIMESTAMP
A socket cannot mix SO_TIMESTAMP and SO_TIMESTAMPNS : the two modes are
mutually exclusive.
sock_recv_timestamp() became too big to be fully inlined so I added a
__sock_recv_timestamp() helper function.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
CC: linux-arch@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Now network timestamps use ktime_t infrastructure, we can add a new
ioctl() SIOCGSTAMPNS command to get timestamps in 'struct timespec'.
User programs can thus access to nanosecond resolution.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
CC: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace uses with of_find_node_by_name and for_each_node_by_name.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is an old interface and is replaced by of_find_compatible_node.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
BenH's commit a741e67969 in powerpc.git,
although (AFAICT) only intended to affect ppc64, also has side-effects
which break 44x. I think 40x, 8xx and Freescale Book E are also
affected, though I haven't tested them.
The problem lies in unconditionally removing flush_tlb_pending() from
the versions of flush_tlb_mm(), flush_tlb_range() and
flush_tlb_kernel_range() used on ppc64 - which are also used the
embedded platforms mentioned above.
The patch below cleans up the convoluted #ifdef logic in tlbflush.h,
in the process restoring the necessary flushes for the software TLB
platforms. There are three sets of definitions for the flushing
hooks: the software TLB versions (revised to avoid using names which
appear to related to TLB batching), the 32-bit hash based versions
(external functions) amd the 64-bit hash based versions (which
implement batching).
It also moves the declaration of update_mmu_cache() to always be in
tlbflush.h (previously it was in tlbflush.h except for PPC64, where it
was in pgtable.h).
Booted on Ebony (440GP) and compiled for 64-bit and 32-bit
multiplatform.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Save the trap number in the case of getting a bad stack in an exception
handler. It is sometimes useful to know what exception it was that caused
this to happen. Without this, no trap number is reported.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Rename MPIC_BROKEN_U3 to something a little more descriptive. Its
effect is to enable support for HT irqs behind the PCI-X/HT bridge on
U3/U4 (aka. CPC9x5) parts.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a driver to arch/powerpc/sysdev for the UIC, the
on-chip interrupt controller from IBM/AMCC 4xx chips. It uses the new
irq host mapping infrastructure.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
For cases when probes are placed on instructions that can be emulated,
don't take the single-step exception.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Oprofile support for PA6T, kernel side.
Also rename the PA6T_SPRN.* defines to SPRN_PA6T.*.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PowerPC 750CL has high BATs. The patch below adds a CPU_FTRS_750CL that
includes that. Without it, the original firmware mappings in the high BATs
aren't cleared which continue to override the linux translations.
It also adds CPU_FTR_COMMON to CPU_FTRS_750GX for completeness.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The of_iomap function maps memory for a given
device_node and returns a pointer to that memory.
This is used at some places, so it makes sense to
a seperate function.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
This patch adds code to deal with conversion of
logical cpu to cbe nodes. It removes code that
assummed there were two logical CPUs per CBE.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Until now, we have always entered the spu page fault handler
with a mutex for the spu context held. This has multiple
bad side-effects:
- it becomes impossible to suspend the context during
page faults
- if an spu program attempts to access its own mmio
areas through DMA, we get an immediate livelock when
the nopage function tries to acquire the same mutex
This patch makes the page fault logic operate on a
struct spu_context instead of a struct spu, and moves it
from spu_base.c to a new file fault.c inside of spufs.
We now also need to copy the dar and dsisr contents
of the last fault into the saved context to have it
accessible in case we schedule out the context before
activating the page fault handler.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Trivial change to pass vmsplice arguments through the compat layer on
pp64.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here's an implementation of DEBUG_PAGEALLOC for ppc32. It disables BAT
mapping and is only tested with Hash table based processor though it
shouldn't be too hard to adapt it to others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
arch/powerpc/Kconfig.debug | 9 ++++++
arch/powerpc/mm/init_32.c | 4 +++
arch/powerpc/mm/pgtable_32.c | 52 +++++++++++++++++++++++++++++++++++++++
arch/powerpc/mm/ppc_mmu_32.c | 4 ++-
include/asm-powerpc/cacheflush.h | 6 ++++
5 files changed, 74 insertions(+), 1 deletion(-)
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current tlb flush code on powerpc 64 bits has a subtle race since we
lost the page table lock due to the possible faulting in of new PTEs
after a previous one has been removed but before the corresponding hash
entry has been evicted, which can leads to all sort of fatal problems.
This patch reworks the batch code completely. It doesn't use the mmu_gather
stuff anymore. Instead, we use the lazy mmu hooks that were added by the
paravirt code. They have the nice property that the enter/leave lazy mmu
mode pair is always fully contained by the PTE lock for a given range
of PTEs. Thus we can guarantee that all batches are flushed on a given
CPU before it drops that lock.
We also generalize batching for any PTE update that require a flush.
Batching is now enabled on a CPU by arch_enter_lazy_mmu_mode() and
disabled by arch_leave_lazy_mmu_mode(). The code epects that this is
always contained within a PTE lock section so no preemption can happen
and no PTE insertion in that range from another CPU. When batching
is enabled on a CPU, every PTE updates that need a hash flush will
use the batch for that flush.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Those are needed by things like alignment exception fixup handlers
since those can now be triggered by copy_tofrom_user_inatomic.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some drivers have resources that they want to be able to map into
userspace that are 4k in size. On a kernel configured with 64k pages
we currently end up mapping the 4k we want plus another 60k of
physical address space, which could contain anything. This can
introduce security problems, for example in the case of an infiniband
adaptor where the other 60k could contain registers that some other
program is using for its communications.
This patch adds a new function, remap_4k_pfn, which drivers can use to
map a single 4k page to userspace regardless of whether the kernel is
using a 4k or a 64k page size. Like remap_pfn_range, it would
typically be called in a driver's mmap function. It only maps a
single 4k page, which on a 64k page kernel appears replicated 16 times
throughout a 64k page. On a 4k page kernel it reduces to a call to
remap_pfn_range.
The way this works on a 64k kernel is that a new bit, _PAGE_4K_PFN,
gets set on the linux PTE. This alters the way that __hash_page_4K
computes the real address to put in the HPTE. The RPN field of the
linux PTE becomes the 4k RPN directly rather than being interpreted as
a 64k RPN. Since the RPN field is 32 bits, this means that physical
addresses being mapped with remap_4k_pfn have to be below 2^44,
i.e. 0x100000000000.
The patch also factors out the code in arch/powerpc/mm/hash_utils_64.c
that deals with demoting a process to use 4k pages into one function
that gets called in the various different places where we need to do
that. There were some discrepancies between exactly what was done in
the various places, such as a call to spu_flush_all_slbs in one case
but not in others.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
We add a device_is_compatible define for compatibility during the
change over.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is more consistent and gets us closer to the Sparc code.
We add a get_property define for compatibility during the change over.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
mtocrf is a faster single-field mtcrf (move to condition register
fields) instruction available in POWER4 and later processors. It can
make quite a difference in performance on some implementations, so use
it for CONFIG_POWER4_ONLY builds.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This common uevent handler allow the several bus types based on
of_device to generate the uevent properly and avoiding
code duplication.
This handlers take a struct device as argument and can therefore
be used as the uevent call directly if no special treatment is
needed for the bus.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The definition of struct ucc_slow puts the guemr register immediately after the
utpt register, when it should be at offset 0x90. This patch adds the missing
0x52-byte padding.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove last_syscall from 32bit powerpc, its been gone in 64bit for years.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The EEH event notification system passes around data that is
not needed or at least, not used properly. Stop passing this
data; get it in a more reliable fashion.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Modify routine that returns PCI slot status to wait for slot status
to become available. This is needed, as slots that are in some remote
card cage may go offline for extended periods of time. New users for
this routine in following patches.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
kexec invokes plpar_hcall hypervisor call in real mode. plpar_hcall
refers to per cpu variables for accounting hypervisor statistics.
These variables may not be in the RMO region, so accesses to them
in real mode may result in a data storage exception.
This fixes this problem by using a new plpar_hcall_raw function which
does not update the hypervisor call statistics. Thanks to Anton for
suggesting this idea.
Signed-off-by: Mohan Kumar M <mohan@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Move the slb_shadow_ptr field into the first cache line since it is
(like everything there) read-only after boot. It is in fact statically
initialised and thereafter only read.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch updates booting-without-of.txt to describe version 17 of
the flattened device tree format. Version 17 is a small, backwards
compatible change from version 16, adding an extra field giving the
size of the device tree's structure block. At this time, the kernel
has no use for the extra information, however its presence can make
life easier for bootloaders or other software manipulating the tree.
In addition this patch adds information on the size_dt_strings field
of the device tree header, present since version 3 of the flattened
tree format, but omitted from the documentation. It also makes
changes to consistently refer to versions 16 and 17 as versions 16 and
17 in decimal, rather than version 0x10 which was occasionally used
for version 16 previously.
Finally, we also add the new field to the definition of the device
tree header structure in prom.h
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds two sysfs attributes to /sys/bus/ibmebus which can be used to
notify the ebus driver of added / removed ebus devices in the OF device
tree.
Echoing the device's location code (as found in the OFDT "ibm,loc-code"
property) into the "probe" attribute will notify ebus of addition of the
device and cause the appropriate device driver's probe function to be called
on the device.
Likewise, echoing the location code into the "remove" attribute will cause
the device to be removed from the system.
The writes will block until the respective operation has finished and return
an error code if the operation failed.
In addition, two minor tidbits are fixed:
- The fake root device used to provide a common parent for all ebus devices
is now based on device instead of of_device - it had no associated devtree
node. This saves several checks throughout the ebus driver.
- The sysfs attributes are now generated automagically by device_register()
instead of by the ibmebus code, which saves a few compiler warnings about
unused return codes.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I forgot to do this when wiring up the syscall.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPU code doesn't properly invalidate SPUs SLBs when necessary,
for example when changing a segment size from the hugetlbfs code. In
addition, it saves and restores the SLB content on context switches
which makes it harder to properly handle those invalidations.
This patch removes the saving & restoring for now, something more
efficient might be found later on. It also adds a spu_flush_all_slbs(mm)
that can be used by the core mm code to flush the SLBs of all SPEs that
are running a given mm at the time of the flush.
In order to do that, it adds a spinlock to the list of all SPEs and move
some bits & pieces from spufs to spu_base.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This will allow us to build without PCI easier.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implements the per arch atomic_scrub() that EDAC uses for software
ECC scrubbing. It reads memory and then writes back the original
value, allowing the hardware to detect and correct memory errors.
Signed-off-by: Dave Jiang <djiang@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I forgot to do this when wiring up the syscall.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In file included from include/asm/pci.h:20,
from include/linux/pci.h:751,
from arch/powerpc/sysdev/dart_iommu.c:36:
include/asm/prom.h: In function `of_irq_to_resource':
include/asm/prom.h:341: warning: implicit declaration of function `irq_of_parse_and_map'
include/asm/prom.h:345: error: `NO_IRQ' undeclared (first use in this function)
include/asm/prom.h:345: error: (Each undeclared identifier is reported only once
include/asm/prom.h:345: error: for each function it appears in.)
Seems that prom.h has always wanted irq.h.
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Remove the SMT-nice feature which idles sibling cpus on SMT cpus to
facilitiate nice working properly where cpu power is shared. The idling of
cpus in the presence of runnable tasks is considered too fragile, easy to
break with outside code, and the complexity of managing this system if an
architecture comes along with many logical cores sharing cpu power will be
unworkable.
Remove the associated per_cpu_gain variable in sched_domains used only by
this code.
Also:
The reason is that with dynticks enabled, this code breaks without yet
further tweaks so dynticks brought on the rapid demise of this code. So
either we tweak this code or kill it off entirely. It was Ingo's preference
to kill it off. Either way this needs to happen for 2.6.21 since dynticks
has gone in.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Refactored and cleaned up ucc_fast.c and ucc_slow.c so that the two files
look more alike and are easier to read. Removed uccf_printk() and related
functions, because they were just front-ends to printk(). Fixed some
spacing and tabbing issues. Minor optimizations of some code. Changed
the type of some variables to their proper type (mostly buffer
descriptors).
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add function of_get_mac_address(), which obtains the best MAC address to use
from the device tree by checking various properties in order. The order is:
'mac-address', then 'local-mac-address', then 'address'. It skips properties
that contain invalid MAC addresses, which were probably not initialized
by U-Boot.
Update gfar_of_init() and fs_enet_of_init() in fsl_soc.c to call
of_get_mac_address().
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Getting BenH's new EMAC driver working on 440GP, I found some more
problems in the native mode paths of the new DCR code:
- dcr_map() is supposed to return a dcr_host_t, but the native
version is a macro that doesn't expand to an expression. With native
DCRs, dcr_host_t is an empty structure, so we just use a constructor
expression instead.
- dcr_unmap() uses {} instead of the safer do {} while (0)
idiom to implement a no-op
Here's a fix.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds driver code for the PMI device found in future IBM products.
PMI stands for "Platform Management Interrupt" and is a way to
communicate with the BMC (Baseboard Management Controller).
It provides bidirectional communication with a low latency.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Acked-by: Heiko J Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add PS3 system manager support and the ppc_md routines restart() and
power_off().
The system manager provides an event notification mechanism for reporting
events like thermal alert and button presses. It also provides support to
control system shutdown and startup.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanups for the PS3 vuart driver.
- Hide driver private data from external interface with new structure
ps3_vuart_port_priv.
- Fix masking bug in ps3_vuart_get_interrupt_status().
- Add new helper routine ps3_vuart_clear_rx_bytes() to flush rx buffer.
- Add new variable probe_mutex to serialize probe and destroy routines.
- Rename some symbols.
- Add platform check in ps3_vuart_bus_init().
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
udbg_early_init() is a function used on 64 bit systems, which
initializes whichever early udbg backend is configured. This function
is not called on 32-bit, however if btext early debug is enabled it
does have an explicit, inline, #ifdef-ed assignment performing
analagous initialization.
This patch makes things more uniform by folding the btext
initialization as an option into udbg_early_init() and calling that
from the 32-bit setup path.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a clean up patch that includes the following changes:
-Some comments were added to clarify the code based on feedback
from the community.
-The write_pm_cntrl() and set_count_mode() were passed a
structure element from a global variable. The argument was
removed so the functions now just operate on the global directly.
-The set_pm_event() function call in the cell_virtual_cntr()
routine was moved to a for-loop before the for_each_cpu loop
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
It doesn't make any sense to have a priority field in the physical spu
structure. Move it into the spu context instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
The recent vDSO consolidation patches broke powerpc due to a mistake
in the definition of MAXPAGES constants. This fixes it by moving to
a dynamically allocated array of pages instead as I don't like much
hard coded size limits. Also move the vdso initialisation to an initcall
since it doesn't really need to be done -that- early.
Applogies for not catching the breakage earlier, Roland _did_ CC me on
his patches a while ago, I got busy with other things and forgot to test
them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
During ppc64+ppc merge virtual DMA code for floppy driver was not
ported. This patch restores virtual DMA support for floppy in new
powerpc target.
It is necessary at least on Pegasos and AmigaOne machines for the
floppy drive to function. ISA DMA controller works incorrectly there
due to its addressing limitations.
Virtual DMA mode is activated by floppy=nodma option passed to the
kernel (or module). There's no automatic switch like on i386.
Signed-off-by: Pavel Fedin <sonic_amiga@rambler.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PS3: Cleanup the frame buffer device before clearing the HPTE mapping
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If ps3fb is available, we have to disable display flipping while changing the
audio or video mode.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the PS3 Virtual Frame Buffer Driver.
As the actual graphics hardware cannot be accessed directly by Linux, ps3fb
uses a virtual frame buffer in main memory. The actual screen image is copied
to graphics memory by the GPU on every vertical blank, by making a hypervisor
call.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Preallocate bootmem memory for the PS3 frame buffer device, which needs a
large block of physically-contiguous memory. The size of this memory block is
configurable:
- The config option CONFIG_FB_PS3_DEFAULT_SIZE_M allows to specify the
default amount of memory (in MiB) allocated to the virtual frame buffer.
- The early boot parameter `ps3fb=xxx' allows to override the default value.
It will be rounded up to a multiple of 1 MiB, if needed.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the PS3 AV Settings Driver.
The AV Settings driver is used to control Audio and Video settings. It
communicates with the policy manager through the virtual uart.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Cc: James Simmons <jsimmons@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The line discipline numbers N_* are currently defined for each architecture
individually, but (except for a seeming mistake) identically, in
asm/termios.h. There is no obvious reason why these numbers should be
architecture specific, nor any apparent relationship with the termios
structure. The total number of these, NR_LDISCS, is defined in linux/tty.h
anyway. So I propose the following patch which moves the definitions of
the individual line disciplines to linux/tty.h too.
Three of these numbers (N_MASC, N_PROFIBUS_FDL, and N_SMSBLOCK) are unused
in the current kernel, but the patch still keeps the complete set in case
there are plans to use them yet.
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rename the 'us_regs' field of the ucc_slow_info structure in ucc_slow.h
to just 'regs'. The equivalent field in the ucc_fast_info structure is
also called 'regs', so this patch makes them comparable, and makes the
code a little easier to read, because there already is a 'us_regs' in
another ucc_slow structure.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The previous patch changing pSeries to use H_BULK_REMOVE broke the
JS20 blade, where the firmware doesn't support H_BULK_REMOVE. This
adds a firmware check so that on machines that don't have H_BULK_REMOVE,
we just use the H_REMOVE call as before.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Added kprobes to ppc32 platforms that have use single_step_exception. This
excludes 4xx and anything Book-E since their debug mechanisms for single stepping
are completely different.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
H_BULK_REMOVE lets us remove 4 entries from the MMU hash table with one
hypervisor call. This uses it in pSeries_lpar_hpte_invalidate so we
can tear down mappings with fewer hypervisor calls.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The new dcr code does not currently compile when configured for native
DCR access on ARCH=powerpc. This patch fixes the problems.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Timebase update is simple on PA6T, since global updates can be done from
one core by writing to an SPR.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Powersave support on PA6T. Right now it only uses 'doze' mode, and
will default to no savings (spin).
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Early debug output for PA Semi UART. Uses the 2.05 CI real mode ops.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
