A side effect of making the dock monitoring interrupt-driven was that
we'd be very quick to program a freshly connected dock. However, for
unclear reasons, the dock does not work when we do that - despite the
FPGA netlist upload going just fine. We work around this by adding a
delay before programming the dock; for safety, the value is several
times as much as was determined empirically.
Note that a badly timed dock hot-plug would have triggered the problem
even before the referenced commit - but now it would happen 100% instead
of about 3% of the time, thus making it impossible to work around by
re-plugging.
Fixes: fbb64eedf5 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-6-oswald.buddenhagen@gmx.de>
The FPGA access through the GPIO port does not interfere with other
sound processor register access, so there is no need to subject it to
emu_lock. And after moving all FPGA access out of the interrupt handler,
it does not need to be IRQ-safe, either.
What's more, attaching the dock causes a firmware upload, which takes
several seconds. We really don't want to disable IRQs for this long, and
even less also have someone else spin with IRQs disabled waiting for us.
Therefore, use a mutex for FPGA access locking.
This makes the code somewhat more noisy, as we need to wrap bigger
sections into the mutex, as it needs to enclose the spinlocks.
The latter has the "side effect" of fixing dock FPGA programming in a
corner case: a really badly timed mixer access right between entering
FPGA programming mode and uploading the netlist would mess up the
protocol.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-5-oswald.buddenhagen@gmx.de>
The actual event processing was already done by workqueue items. We can
move the event dispatching there as well, rather than doing it already
in the interrupt handler callback.
This change has a rather profound "side effect" on the reliability of
the FPGA programming: once we enter programming mode, we must not issue
any snd_emu1010_fpga_{read,write}() calls until we're done, as these
would badly mess up the programming protocol. But exactly that would
happen when trying to program the dock, as that triggers GPIO interrupts
as a side effect. This is mitigated by deferring the actual interrupt
handling, as workqueue items are not re-entrant.
To avoid scheduling the dispatcher on non-events, we now explicitly
ignore GPIO IRQs triggered by "uninteresting" pins, which happens a lot
as a side effect of calling snd_emu1010_fpga_{read,write}().
Fixes: fbb64eedf5 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-4-oswald.buddenhagen@gmx.de>
Pulled out of the next patch to improve its legibility.
As the function is now available, call it directly from
snd_emu10k1_emu1010_init(), thus making the MicroDock firmware loading
synchronous - there isn't really a reason not to. Note that this does
not affect the AudioDocks of rev1 cards, as these have no independent
power supplies, and thus come up only a while after the main card is
initialized.
As a drive-by, adjust the priorities of two messages to better reflect
their impact.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-3-oswald.buddenhagen@gmx.de>
While there are two separate IRQ status bits for dock attach and detach,
the hardware appears to mix them up more or less randomly, making them
useless for tracking what actually happened. It is much safer to check
the dock status separately and proceed based on that, as the old polling
code did.
Note that the code assumes that only the dock can be hot-plugged - if
other option card bits changed, the logic would break.
Fixes: fbb64eedf5 ("ALSA: emu10k1: make E-MU dock monitoring interrupt-driven")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218584
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240428093716.3198666-2-oswald.buddenhagen@gmx.de>
The Haier Boyue G42 with ALC269VC cannot detect the MIC of headset,
the line out and internal speaker until
ALC269VC_FIXUP_ACER_VCOPPERBOX_PINS quirk applied.
Signed-off-by: Ai Chao <aichao@kylinos.cn>
Cc: <stable@vger.kernel.org>
Message-ID: <20240419082159.476879-1-aichao@kylinos.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The headset mic requires a fixup to be properly detected/used.
As a reference, this specific model from 2021 reports
the following devices:
https://alsa-project.org/db/?f=1a5ddeb0b151db8fe051407f5bb1c075b7dd3e4a
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: <stable@vger.kernel.org>
Message-ID: <b92a9e49fb504eec8416bcc6882a52de89450102.1713370457.git.mchehab@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the correct pin table for Asus GU605M and GA403U, enabling all
speakers to be controlled with the master.
Updated quirks for GU605M and GA403U by including the pin table patch
in the chain.
Co-developed-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Vitalii Torshyn <vitaly.torshyn@gmail.com>
Message-ID: <20240411125803.18539-1-vitaly.torshyn@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add new vendor_id and subsystem_id to support new Lenovo laptop
ThinkPad ICE-1
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Cc: <stable@vger.kernel.org>
Message-ID: <20240411091823.1644-1-shenghao-ding@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Calibrated data was written into an incorrect register, which cause
speaker protection sometimes malfuctions
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Cc: <stable@vger.kernel.org>
Message-ID: <20240406132010.341-1-shenghao-ding@ti.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for HP SnowWhite laptops with CS35L51 amplifiers on I2C
bus connected to Realtek codec.
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Message-ID: <20240405210635.22193-1-vitalyr@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixes the realtek quirk to initialise the Cirrus amp correctly and adds
related quirk for missing DSD properties. This model laptop has slightly
updated internals compared to the previous version with Realtek Codec
ID of 0x1caf.
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Cc: <stable@vger.kernel.org>
Message-ID: <20240402015126.21115-1-luke@ljones.dev>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch addresses an issue with the Panasonic CF-SZ6's existing quirk,
specifically its headset microphone functionality. Previously, the quirk
used ALC269_FIXUP_HEADSET_MODE, which does not support the CF-SZ6's design
of a single 3.5mm jack for both mic and audio output effectively. The
device uses pin 0x19 for the headset mic without jack detection.
Following verification on the CF-SZ6 and discussions with the original
patch author, i determined that the update to
ALC269_FIXUP_ASPIRE_HEADSET_MIC is the appropriate solution. This change
is custom-designed for the CF-SZ6's unique hardware setup, which includes
a single 3.5mm jack for both mic and audio output, connecting the headset
microphone to pin 0x19 without the use of jack detection.
Fixes: 0fca97a29b ("ALSA: hda/realtek - Add Panasonic CF-SZ6 headset jack quirk")
Signed-off-by: I Gede Agastya Darma Laksana <gedeagas22@gmail.com>
Cc: <stable@vger.kernel.org>
Message-ID: <20240401174602.14133-1-gedeagas22@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes the sound not working from internal speakers on
Lenovo Legion Slim 7 16ARHA7 models. The correct subsystem ID
have been added to cs35l41_hda_property.c and patch_realtek.c.
Signed-off-by: Christian Bendiksen <christian@bendiksen.me>
Cc: <stable@vger.kernel.org>
Message-ID: <20240401122603.6634-1-christian@bendiksen.me>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As already anticipated in the original commit, playback was broken for
very short samples. I just didn't expect it to be an actual problem,
because we're talking about less than 1.5 milliseconds here. But clearly
such wavetable samples do actually exist.
The problem was that for such short samples we'd set the current
position beyond the end of the loop, so we'd run off the end of the
sample and play garbage.
This is a bigger (more audible) problem than the original one, which was
that we'd start playback with garbage (whatever was still in the cache),
which would be mostly masked by the note's attack phase.
So revert to the old behavior for now. We'll subsequently fix it
properly with a bigger patch series.
Note that this isn't a full revert - the dead code is not re-introduced,
because that would be silly.
Fixes: df335e9a8b ("ALSA: emu10k1: fix synthesizer sample playback position and caching")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218625
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Message-ID: <20240401145805.528794-1-oswald.buddenhagen@gmx.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These ASUS laptops use the Realtek HDA codec combined with a number of
CS35L56 amplifiers.
The SSID of the GA403U matches a previous ASUS laptop - we can tell them
apart because they use different codecs.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Message-ID: <20240329112803.23897-1-simont@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding the ACPI HIDs to the match table triggers the cs35l56-hda modules
to be loaded on boot so that Serial Multi Instantiate can add the
devices to the bus and begin the driver init sequence.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Message-ID: <20240328121355.18972-1-simont@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the existing fixup to certain TF platforms implementing
the ALC274 codec with a headset jack. It fixes/activates the inactive
microphone of the headset.
Signed-off-by: Christoffer Sandberg <cs@tuxedo.de>
Signed-off-by: Werner Sembach <wse@tuxedocomputers.com>
Cc: <stable@vger.kernel.org>
Message-ID: <20240328102757.50310-1-wse@tuxedocomputers.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The debug message "Playback action not supported: action" is not useful,
because the action was previously printed, and the list of supported
actions are intentional.
Remove the debug statement from the default switch case.
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Message-ID: <8b9546db6c92dea4476a7247a88d56248c2ba8c2.1711469583.git.soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Sometimes it is useful to examine the timing of kcontrol events.
Add debug statements to each kcontrol.
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Message-ID: <18ff4b0caab90a2dacf907e62346fd5079a9eb1a.1711469583.git.soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "Speaker Digital Gain" kcontrol controls the TAS2781_DVC_LVL (0x1A)
register. Unfortunately the tas2563 does not have DVC_LVL, but has
INT_MASK0 in 0x1A, which has been misused so far.
Since commit c1947ce61f ("ALSA: hda/realtek: tas2781: enable subwoofer
volume control") the volume of the tas2781 amplifiers can be controlled
by the master volume, so this digital gain kcontrol is not needed.
Remove it.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Message-ID: <741fc21db994efd58f83e7aef38931204961e5b2.1711469583.git.soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialization is completed before adding the component as that can
start the process of the device binding and trigger actions that check
init_done.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Message-ID: <20240325145510.328378-1-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The system and amplifier names influence which firmware and tuning files
are downloaded to the device; log these values to aid end-user system
support.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-ID: <20240325142937.257869-1-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cirrus amps support for this laptop was added in patch:
33e5e648e6 ("ALSA: hda: cs35l41: Support additional HP Envy Models")
This patch adds fixes for wrong pincfgs, wrong DAC selection and
mute/micmute LEDs.
Signed-off-by: Anthony I Gilea <i@cpp.in>
Message-ID: <e2a7aaed-e9d7-4d36-8abf-b71dfd32a0ff@cpp.in>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently we tested the headphone playback on 2 LG machines, if we set
the volume to the max value or near to the max value, the sound is too
loud, it could even bring harm to listeners.
A workaround is to decrease the max volume to a reasonable value for
the headphone's amplifier, then the users couldn't set the volume
bigger than that value from the userspace.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Message-ID: <20240318011128.156023-1-hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Keyboard has an LED that is ON/OFF when mic is muted/active
- LED is controlled by GPIO pin
- Patch enables led to appear in /sys/class/leds/ as hda::micmute
- Enables LED when mic is MUTED
- Disables LED when mic is active
[ fixed white spaces by tiwai ]
Signed-off-by: Ian Murphy <iano200@gmail.com>
Message-ID: <20240316094157.13890-1-iano200@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The speakers on the Lenovo Yoga 9 14IMH9 are similar to previous generations
such as the 14IAP7, and the bass speakers can be fixed using similar methods
with one caveat: 14IMH9 uses CS35L41 amplifiers which need to be activated
separately.
Signed-off-by: Jichi Zhang <i@jichi.ca>
Message-ID: <20240315081954.45470-3-i@jichi.ca>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The runtime_pm handling seems to have been loosely inspired by the
cs32l41 driver, but in this case the get_noresume/put sequence is not
required.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Message-ID: <20240312161217.79510-1-pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some HP laptops have received revisions that altered their board IDs
and therefore the current patches/quirks do not apply to them.
Specifically, for my Probook 440 G8, I have a board ID of 8a74.
It is necessary to add a line for that specific model.
Signed-off-by: Valentine Altair <faetalize@proton.me>
Cc: <stable@vger.kernel.org>
Message-ID: <kOqXRBcxkKt6m5kciSDCkGqMORZi_HB3ZVPTX5sD3W1pKxt83Pf-WiQ1V1pgKKI8pYr4oGvsujt3vk2zsCE-DDtnUADFG6NGBlS5N3U4xgA=@proton.me>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This has been quite a small release, there's a lot of driver specific
cleanups and minor enhancements but hardly anything on the core and only
one new driver. Highlights include:
- SoundWire support for AMD ACP 6.3 systems.
- Support for reporting version information for AVS firmware.
- Support DSPless mode for Intel Soundwire systems.
- Support for configuring CS35L56 amplifiers using EFI calibration
data.
- Log which component is being operated on as part of power management
trace events.
- Support for Microchip SAM9x7, NXP i.MX95 and Qualcomm WCD939x
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmXvE1AACgkQJNaLcl1U
h9B15Qf8CrS5zHsD54bvTcumkDgbJ8Dl9f5qz4UN/AX0mcZ1UJU6sQ0HxIGEtlPc
26pneHV9ZA0wSPw432NBpwcfe7AsWASmKUf6S2hsj4LMvnoj75iiZum8TE71ior7
QI9ARnNipB1tHk7Kmgs/pe+CqX3hhCVqYUI9w5fMIj05T5qwYbqCERws6JA2Uw97
6fb5CgI2uRYTShVVmYsE/FlxXmZqNN4NnNxlVvUSM5TE3Tayf+BCEqhpwuh59Pt/
G+mZfj3eof0HdjGPQbLRPOWQOa3bT8gmT89OlbmmMf17+975pgShBbARzkv41vk1
ifr6muHweaDLD7gloS/HUr4JRo9Daw==
=ZYC5
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v6.9
This has been quite a small release, there's a lot of driver specific
cleanups and minor enhancements but hardly anything on the core and only
one new driver. Highlights include:
- SoundWire support for AMD ACP 6.3 systems.
- Support for reporting version information for AVS firmware.
- Support DSPless mode for Intel Soundwire systems.
- Support for configuring CS35L56 amplifiers using EFI calibration
data.
- Log which component is being operated on as part of power management
trace events.
- Support for Microchip SAM9x7, NXP i.MX95 and Qualcomm WCD939x
After system_resume the amplifers will remain off, even if they were on
before system_suspend.
Use playback_started bool to save the playback state, and restore power
state based on it.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <1742b61901781826f6e6212ffe1d21af542d134a.1709918447.git.soyer@irl.hu>
The runtime_resume function calls prmg_load and apply_calibration
functions, but system_resume also calls them, so calling
pm_runtime_force_resume before reset is unnecessary.
For consistency, do not call the pm_runtime_force_suspend in
system_suspend, as runtime_suspend does the same.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <d0b4cc1248b9d375d59c009563da42d60d69eac3.1709918447.git.soyer@irl.hu>
The amplifier doesn't loose register state in software shutdown mode, so
there is no need to reset the cur_* values.
Without these resets, the amplifier can be turned on after
runtime_suspend without waiting for the program and
profile to be restored.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <aa27ae084150988bf6a0ead7e3403bc485d790f8.1709918447.git.soyer@irl.hu>
The system_resume function uses dev_info for tracing, but the other pm
functions use dev_dbg.
Use dev_dbg as the other pm functions.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <140f3c689c9eb5874e6eb48a570fcd8207f06a41.1709918447.git.soyer@irl.hu>
Realtek codec on HP Envy laptop series are heavily modified by vendor.
Therefore, need intervention to make it work properly. The patch fixes:
- B&O soundbar speakers (between lid and keyboard) activation
- Enable LED on mute button
- Add missing process coefficient which affects the output amplifier
- Volume control synchronization between B&O soundbar and side speakers
- Unmute headset output on several HP Envy models
- Auto-enable headset mic when plugged
This patch was tested on HP Envy x360 13-AR0107AU with Realtek ALC285
The only unsolved problem is output amplifier of all built-in speakers
is too weak, which causes volume of built-in speakers cannot be loud
as vendor's proprietary driver due to missing _DSD parameter in the
firmware. The solution is currently on research. Expected to has another
patch in the future.
Potential fix to related issues, need test before close those issues:
- https://bugzilla.kernel.org/show_bug.cgi?id=189331
- https://bugzilla.kernel.org/show_bug.cgi?id=216632
- https://bugzilla.kernel.org/show_bug.cgi?id=216311
- https://bugzilla.kernel.org/show_bug.cgi?id=213507
Signed-off-by: Athaariq Ardhiansyah <foss@athaariq.my.id>
Message-ID: <20240310140249.3695-1-foss@athaariq.my.id>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the HID for the CS35L54 and CS35L57 Boosted Smart Amplifiers. These
have the same control interface as the CS35L56 so are handled by the
cs35l56-hda driver.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Message-ID: <20240308135900.603192-3-rf@opensource.cirrus.com>
hda_component.h uses hda_codec_dev from sound/hda_codec.h.
Include sound/hda_codec.h instead of assuming that it has already
been included by the parent .c file.
This isn't causing any problems with current code, so no need to
backport to older kernels.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-ID: <20240307111216.45053-2-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the conventional include guards around the content of the
hda_component.h header file. This prevents double-declaration of
struct hda_component if the header gets included multiple times.
This isn't causing any problems with current code, so no need to
backport to older kernels.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Message-ID: <20240307111216.45053-1-rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP EliteBook using ALC236 codec which using 0x02 to
control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240304134033.773348-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There was one overlooked place to be replaced with
snd_ctl_find_id_mixer() for code simplification.
No functional change, only code refactoring.
Link: https://lore.kernel.org/r/20240304082158.8583-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Whilst this laptop contains _DSD inside the BIOS, there is an error in
this configuration. Override the _DSD in the BIOS with the correct
configuration for this laptop.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240301160154.158398-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
