No functional change.
Prepares for support of allocating and affinitizing sets of interrupts, in
which each set of interrupts needs a full two stage spreading. The first
vector argument is necessary for this so the affinitizing starts from the
first vector of each set.
[ tglx: Minor changelog tweaks ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Hannes Reinecke <hare@suse.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Link: https://lkml.kernel.org/r/20181102145951.31979-4-ming.lei@redhat.com
No functional change. Prepares for supporting allocating and affinitizing
interrupt sets.
[ tglx: Minor changelog tweaks ]
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Cc: Hannes Reinecke <hare@suse.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Link: https://lkml.kernel.org/r/20181102145951.31979-3-ming.lei@redhat.com
If the number of NUMA nodes exceeds the number of MSI/MSI-X interrupts
which are allocated for a device, the interrupt affinity spreading code
fails to spread them across all nodes.
The reason is, that the spreading code starts from node 0 and continues up
to the number of interrupts requested for allocation. This leaves the nodes
past the last interrupt unused.
This results in interrupt concentration on the first nodes which violates
the assumption of the block layer that all nodes are covered evenly. As a
consequence the NUMA nodes above the number of interrupts are all assigned
to hardware queue 0 and therefore NUMA node 0, which results in bad
performance and has CPU hotplug implications, because queue 0 gets shut
down when the last CPU of node 0 is offlined.
Go over all NUMA nodes and assign them round-robin to all requested
interrupts to solve this.
[ tglx: Massaged changelog ]
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Cc: Michael Kelley <mikelley@microsoft.com>
Link: https://lkml.kernel.org/r/20181102180248.13583-1-longli@linuxonhyperv.com
Bindings for "fixed-regulator" only explicitly support "gpio" property,
not "gpios". Fix by correcting the property name.
The enet PHYs on imx6sx-sdb needs to be explicitly reset after a power
cycle, this can be handled by the phy-reset-gpios property. Sadly this
is not handled on suspend: the fec driver turns phy-supply off but
doesn't assert phy-reset-gpios again on resume.
Since additional phy-level work is required to support powering off the
phy in suspend fix the problem by just marking the regulator as
"boot-on" "always-on" so that it's never turned off. This behavior is
equivalent to older releases.
Keep the phy-reset-gpios property on fec anyway because it is a correct
description of board design.
This issue was exposed by commit efdfeb079c ("regulator: fixed:
Convert to use GPIO descriptor only") which causes the "gpios" property
to also be parsed. Before that commit the "gpios" property had no
effect, PHY reset was only handled in the the bootloader.
This fixes linux-next boot failures previously reported here:
https://lore.kernel.org/patchwork/patch/982437/#1177900https://lore.kernel.org/patchwork/patch/994091/#1178304
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A quoted label reference doesn't expand to the node path and is taken as
a literal string. Dropping the quotes can fix this unless the baudrate
string is appended in which case we have to use the alias.
At least on VF610, the problem was masked by setting the console in
bootargs. Use the alias syntax with baudrate parameter so we can drop
setting the console in bootargs.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the type of compatible string "fs,imx6sll-i2c" which should be
"fsl,imx6sll-i2c".
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 4d2c0cda07 set slave->link to
BOND_LINK_DOWN for 802.3ad bonds whenever invalid speed/duplex values
were read, to fix a problem with slaves getting into weird states, but
in the process, broke tracking of link failures, as going straight to
BOND_LINK_DOWN when a link is indeed down (cable pulled, switch rebooted)
means we broke out of bond_miimon_inspect()'s BOND_LINK_DOWN case because
!link_state was already true, we never incremented commit, and never got
a chance to call bond_miimon_commit(), where slave->link_failure_count
would be incremented. I believe the simple fix here is to mark the slave
as BOND_LINK_FAIL, and let bond_miimon_inspect() transition the link from
_FAIL to either _UP or _DOWN, and in the latter case, we now get proper
incrementing of link_failure_count again.
Fixes: 4d2c0cda07 ("bonding: speed/duplex update at NETDEV_UP event")
CC: Mahesh Bandewar <maheshb@google.com>
CC: David S. Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: stable@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 4.19 the following error in sysfs has appeared when using the
r8169 NIC driver:
$cd /sys/module/realtek/drivers
$ls -l
ls: cannot access 'mdio_bus:RTL8201F 10/100Mbps Ethernet': No such file or directory
[..garbled dir entries follow..]
Apparently the forward slash in "10/100Mbps Ethernet" is interpreted
as directory separator that leads nowhere, and was introduced in commit
513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions").
Fix this by removing the offending slash in the driver name.
Other drivers in net/phy seem to have the same problem, but I cannot
test/verify them.
Fixes: 513588dd44 ("net: phy: realtek: add RTL8201F phy-id and functions")
Signed-off-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If gcc decides not to inline make_sensor_label():
WARNING: vmlinux.o(.text+0x4df549c): Section mismatch in reference from the function .create_device_attrs() to the function .init.text:.make_sensor_label()
The function .create_device_attrs() references
the function __init .make_sensor_label().
This is often because .create_device_attrs lacks a __init
annotation or the annotation of .make_sensor_label is wrong.
As .probe() can be called after freeing of __init memory, all __init
annotiations in the driver are bogus, and should be removed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
- Full filesystem authentication feature,
UBIFS is now able to have the whole filesystem structure
authenticated plus user data encrypted and authenticated.
- Minor cleanups
-----BEGIN PGP SIGNATURE-----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=lq2m
-----END PGP SIGNATURE-----
Merge tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs
Pull UBIFS updates from Richard Weinberger:
- Full filesystem authentication feature, UBIFS is now able to have the
whole filesystem structure authenticated plus user data encrypted and
authenticated.
- Minor cleanups
* tag 'tags/upstream-4.20-rc1' of git://git.infradead.org/linux-ubifs: (26 commits)
ubifs: Remove unneeded semicolon
Documentation: ubifs: Add authentication whitepaper
ubifs: Enable authentication support
ubifs: Do not update inode size in-place in authenticated mode
ubifs: Add hashes and HMACs to default filesystem
ubifs: authentication: Authenticate super block node
ubifs: Create hash for default LPT
ubfis: authentication: Authenticate master node
ubifs: authentication: Authenticate LPT
ubifs: Authenticate replayed journal
ubifs: Add auth nodes to garbage collector journal head
ubifs: Add authentication nodes to journal
ubifs: authentication: Add hashes to index nodes
ubifs: Add hashes to the tree node cache
ubifs: Create functions to embed a HMAC in a node
ubifs: Add helper functions for authentication support
ubifs: Add separate functions to init/crc a node
ubifs: Format changes for authentication support
ubifs: Store read superblock node
ubifs: Drop write_node
...
Pull more timer updates from Thomas Gleixner:
"A set of commits for the new C-SKY architecture timers"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dt-bindings: timer: gx6605s SOC timer
clocksource/drivers/c-sky: Add gx6605s SOC system timer
dt-bindings: timer: C-SKY Multi-processor timer
clocksource/drivers/c-sky: Add C-SKY SMP timer
private struct, and a few bug fixes.
-----BEGIN PGP SIGNATURE-----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=EhpD
-----END PGP SIGNATURE-----
Merge tag 'ntb-4.20' of git://github.com/jonmason/ntb
Pull NTB updates from Jon Mason:
"Fairly minor changes and bug fixes:
NTB IDT thermal changes and hook into hwmon, ntb_netdev clean-up of
private struct, and a few bug fixes"
* tag 'ntb-4.20' of git://github.com/jonmason/ntb:
ntb: idt: Alter the driver info comments
ntb: idt: Discard temperature sensor IRQ handler
ntb: idt: Add basic hwmon sysfs interface
ntb: idt: Alter temperature read method
ntb_netdev: Simplify remove with client device drvdata
NTB: transport: Try harder to alloc an aligned MW buffer
ntb: ntb_transport: Mark expected switch fall-throughs
ntb: idt: Set PCIe bus address to BARLIMITx
NTB: ntb_hw_idt: replace IS_ERR_OR_NULL with regular NULL checks
ntb: intel: fix return value for ndev_vec_mask()
ntb_netdev: fix sleep time mismatch
According to rfc8260#section-4.3.2, SCTP_SS_DEFAULT is required to
defined as SCTP_SS_FCFS or SCTP_SS_RR.
SCTP_SS_FCFS is used for SCTP_SS_DEFAULT's value in this patch.
Fixes: 5bbbbe32a4 ("sctp: introduce stream scheduler foundations")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As defined in rfc6525#section-6.1.3, SCTP_STREAM_CHANGE_DENIED
and SCTP_STREAM_CHANGE_FAILED should be used instead of
SCTP_ASSOC_CHANGE_DENIED and SCTP_ASSOC_CHANGE_FAILED.
To keep the compatibility, fix it by adding two macros.
Fixes: b444153fb5 ("sctp: add support for generating add stream change event notification")
Reported-by: Jianwen Ji <jiji@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-11-03
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix BPF prog kallsyms and bpf_prog_get_info_by_fd() jited address export
to not use page start but actual start instead to work correctly with
profiling e.g. finding hot instructions from stack traces. Also fix latter
with regards to dumping address and jited len for !multi prog, from Song.
2) Fix bpf_prog_get_info_by_fd() for !root to zero info.nr_jited_func_lens
instead of leaving the user provided length, from Daniel.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU policer used to police packets being trapped via a local route
(IP2ME) was incorrectly configured to police based on bytes per second
instead of packets per second.
Change the policer to police based on packets per second and avoid
packet loss under certain circumstances.
Fixes: 9148e7cf73 ("mlxsw: spectrum: Add policers for trap groups")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_CC_OPTIMIZE_FOR_DEBUGGING is enabled, the compiler
fails to optimize out a dead code path, which leads to a link failure:
net/openvswitch/conntrack.o: In function `ovs_ct_set_labels':
conntrack.c:(.text+0x2e60): undefined reference to `nf_connlabels_replace'
In this configuration, we can take a shortcut, and completely
remove the contrack label code. This may also help the regular
optimization.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-8 notices that qed_mcp_get_transceiver_data() may fail to
return a result to the caller:
drivers/net/ethernet/qlogic/qed/qed_mcp.c: In function 'qed_mcp_trans_speed_mask':
drivers/net/ethernet/qlogic/qed/qed_mcp.c:1955:2: error: 'transceiver_type' may be used uninitialized in this function [-Werror=maybe-uninitialized]
When an error is returned by qed_mcp_get_transceiver_data(), we
should propagate that to the caller of qed_mcp_trans_speed_mask()
rather than continuing with uninitialized data.
Fixes: c56a8be7e7 ("qed: Add supported link and advertise link to display in ethtool.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull scheduler fixes from Ingo Molnar:
"A memory (under-)allocation fix and a comment fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/topology: Fix off by one bug
sched/rt: Update comment in pick_next_task_rt()
Pull x86 fixes from Ingo Molnar:
"A number of fixes and some late updates:
- make in_compat_syscall() behavior on x86-32 similar to other
platforms, this touches a number of generic files but is not
intended to impact non-x86 platforms.
- objtool fixes
- PAT preemption fix
- paravirt fixes/cleanups
- cpufeatures updates for new instructions
- earlyprintk quirk
- make microcode version in sysfs world-readable (it is already
world-readable in procfs)
- minor cleanups and fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
compat: Cleanup in_compat_syscall() callers
x86/compat: Adjust in_compat_syscall() to generic code under !COMPAT
objtool: Support GCC 9 cold subfunction naming scheme
x86/numa_emulation: Fix uniform-split numa emulation
x86/paravirt: Remove unused _paravirt_ident_32
x86/mm/pat: Disable preemption around __flush_tlb_all()
x86/paravirt: Remove GPL from pv_ops export
x86/traps: Use format string with panic() call
x86: Clean up 'sizeof x' => 'sizeof(x)'
x86/cpufeatures: Enumerate MOVDIR64B instruction
x86/cpufeatures: Enumerate MOVDIRI instruction
x86/earlyprintk: Add a force option for pciserial device
objtool: Support per-function rodata sections
x86/microcode: Make revision and processor flags world-readable
Pull perf updates and fixes from Ingo Molnar:
"These are almost all tooling updates: 'perf top', 'perf trace' and
'perf script' fixes and updates, an UAPI header sync with the merge
window versions, license marker updates, much improved Sparc support
from David Miller, and a number of fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (66 commits)
perf intel-pt/bts: Calculate cpumode for synthesized samples
perf intel-pt: Insert callchain context into synthesized callchains
perf tools: Don't clone maps from parent when synthesizing forks
perf top: Start display thread earlier
tools headers uapi: Update linux/if_link.h header copy
tools headers uapi: Update linux/netlink.h header copy
tools headers: Sync the various kvm.h header copies
tools include uapi: Update linux/mmap.h copy
perf trace beauty: Use the mmap flags table generated from headers
perf beauty: Wire up the mmap flags table generator to the Makefile
perf beauty: Add a generator for MAP_ mmap's flag constants
tools include uapi: Update asound.h copy
tools arch uapi: Update asm-generic/unistd.h and arm64 unistd.h copies
tools include uapi: Update linux/fs.h copy
perf callchain: Honour the ordering of PERF_CONTEXT_{USER,KERNEL,etc}
perf cs-etm: Correct CPU mode for samples
perf unwind: Take pgoff into account when reporting elf to libdwfl
perf top: Do not use overwrite mode by default
perf top: Allow disabling the overwrite mode
perf trace: Beautify mount's first pathname arg
...
Pull irq fixes from Ingo Molnar:
"An irqchip driver fix and a memory (over-)allocation fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/irq-mvebu-sei: Fix a NULL vs IS_ERR() bug in probe function
irq/matrix: Fix memory overallocation
With the addition of the NUMA identity level, we increased @level by
one and will run off the end of the array in the distance sort loop.
Fixed: 051f3ca02e ("sched/topology: Introduce NUMA identity node sched domain")
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The vport should be initialized to hdev->vport for each bp group,
otherwise it will cause out-of-bounds access and bp setting not
correct problem.
[ 35.254124] BUG: KASAN: slab-out-of-bounds in hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254126] Read of size 2 at addr ffff803b6651581a by task kworker/0:1/14
[ 35.254132] CPU: 0 PID: 14 Comm: kworker/0:1 Not tainted 4.19.0-rc7-hulk+ #85
[ 35.254133] Hardware name: Huawei D06/D06, BIOS Hisilicon D06 UEFI RC0 - B052 (V0.52) 09/14/2018
[ 35.254141] Workqueue: events work_for_cpu_fn
[ 35.254144] Call trace:
[ 35.254147] dump_backtrace+0x0/0x2f0
[ 35.254149] show_stack+0x24/0x30
[ 35.254154] dump_stack+0x110/0x184
[ 35.254157] print_address_description+0x168/0x2b0
[ 35.254160] kasan_report+0x184/0x310
[ 35.254162] __asan_load2+0x7c/0xa0
[ 35.254170] hclge_pause_setup_hw+0x2a0/0x3f8 [hclge]
[ 35.254177] hclge_tm_init_hw+0x794/0x9f0 [hclge]
[ 35.254184] hclge_tm_schd_init+0x48/0x58 [hclge]
[ 35.254191] hclge_init_ae_dev+0x778/0x1168 [hclge]
[ 35.254196] hnae3_register_ae_dev+0x14c/0x298 [hnae3]
[ 35.254206] hns3_probe+0x88/0xa8 [hns3]
[ 35.254210] local_pci_probe+0x7c/0xf0
[ 35.254212] work_for_cpu_fn+0x34/0x50
[ 35.254214] process_one_work+0x4d4/0xa38
[ 35.254216] worker_thread+0x55c/0x8d8
[ 35.254219] kthread+0x1b0/0x1b8
[ 35.254222] ret_from_fork+0x10/0x1c
[ 35.254224] The buggy address belongs to the page:
[ 35.254228] page:ffff7e00ed994400 count:1 mapcount:0 mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 35.273835] flags: 0xfffff8000008000(head)
[ 35.282007] raw: 0fffff8000008000 dead000000000100 dead000000000200 0000000000000000
[ 35.282010] raw: 0000000000000000 0000000000000000 00000001ffffffff 0000000000000000
[ 35.282012] page dumped because: kasan: bad access detected
[ 35.282014] Memory state around the buggy address:
[ 35.282017] ffff803b66515700: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282019] ffff803b66515780: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282021] >ffff803b66515800: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282022] ^
[ 35.282024] ffff803b66515880: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282026] ffff803b66515900: fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe fe
[ 35.282028] ==================================================================
[ 35.282029] Disabling lock debugging due to kernel taint
[ 35.282747] hclge driver initialization finished.
Fixes: 67bf2541f4 ("net: hns3: Fixes the back pressure setting when sriov is enabled")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
net: bql: better deal with GSO
While BQL bulk dequeue works well for TSO packets, it is
not very efficient as soon as GSO is involved.
On a GSO only workload (UDP or TCP), this patch series
can save about 8 % of cpu cycles on a 40Gbit mlx4 NIC,
by keeping optimal batching, and avoiding expensive
doorbells, qdisc requeues and reschedules.
This patch series :
- Add __netdev_tx_sent_queue() so that drivers
can implement efficient BQL and xmit_more support.
- Implement a work around in dev_hard_start_xmit()
for drivers not using __netdev_tx_sent_queue()
- changes mlx4 to use __netdev_tx_sent_queue()
v2: Tariq and Willem feedback addressed.
added __netdev_tx_sent_queue() (Willem suggestion)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
doorbell only depends on xmit_more and netif_tx_queue_stopped()
Using __netdev_tx_sent_queue() avoids messing with BQL stop flag,
and is more generic.
This patch increases performance on GSO workload by keeping
doorbells to the minimum required.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before calling dev_hard_start_xmit(), upper layers tried
to cook optimal skb list based on BQL budget.
Problem is that GSO packets can end up comsuming more than
the BQL budget.
Breaking the loop is not useful, since requeued packets
are ahead of any packets still in the qdisc.
It is also more expensive, since next TX completion will
push these packets later, while skbs are not in cpu caches.
It is also a behavior difference with TSO packets, that can
break the BQL limit by a large amount.
Note that drivers should use __netdev_tx_sent_queue()
in order to have optimal xmit_more support, and avoid
useless atomic operations as shown in the following patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When qdisc_run() tries to use BQL budget to bulk-dequeue a batch
of packets, GSO can later transform this list in another list
of skbs, and each skb is sent to device ndo_start_xmit(),
one at a time, with skb->xmit_more being set to one but
for last skb.
Problem is that very often, BQL limit is hit in the middle of
the packet train, forcing dev_hard_start_xmit() to stop the
bulk send and requeue the end of the list.
BQL role is to avoid head of line blocking, making sure
a qdisc can deliver high priority packets before low priority ones.
But there is no way requeued packets can be bypassed by fresh
packets in the qdisc.
Aborting the bulk send increases TX softirqs, and hot cache
lines (after skb_segment()) are wasted.
Note that for TSO packets, we never split a packet in the middle
because of BQL limit being hit.
Drivers should be able to update BQL counters without
flipping/caring about BQL status, if the current skb
has xmit_more set.
Upper layers are ultimately responsible to stop sending another
packet train when BQL limit is hit.
Code template in a driver might look like the following :
send_doorbell = __netdev_tx_sent_queue(tx_queue, nr_bytes, skb->xmit_more);
Note that __netdev_tx_sent_queue() use is not mandatory,
since following patch will change dev_hard_start_xmit()
to not care about BQL status.
But it is highly recommended so that xmit_more full benefits
can be reached (less doorbells sent, and less atomic operations as well)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few fixes who have come in near or during the merge window:
- Removal of a VLA usage in Marvell mpp platform code
- Enable some IPMI options for ARM64 servers by default, helps testing
- Enable PREEMPT on 32-bit ARMv7 defconfig
- Minor fix for stm32 DT (removal of an unused DMA property)
- Bugfix for TI OMAP1-based ams-delta (-EINVAL -> IRQ_NOTCONNECTED)
-----BEGIN PGP SIGNATURE-----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=mr8i
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A few fixes who have come in near or during the merge window:
- Removal of a VLA usage in Marvell mpp platform code
- Enable some IPMI options for ARM64 servers by default, helps
testing
- Enable PREEMPT on 32-bit ARMv7 defconfig
- Minor fix for stm32 DT (removal of an unused DMA property)
- Bugfix for TI OMAP1-based ams-delta (-EINVAL -> IRQ_NOTCONNECTED)"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: stm32: update HASH1 dmas property on stm32mp157c
ARM: orion: avoid VLA in orion_mpp_conf
ARM: defconfig: Update multi_v7 to use PREEMPT
arm64: defconfig: Enable some IPMI configs
soc: ti: QMSS: Fix usage of irq_set_affinity_hint
ARM: OMAP1: ams-delta: Fix impossible .irq < 0
- Fix W+X page (mark RO) allocated by the arm64 kprobes code
- Makefile fix for .i files in out of tree modules
-----BEGIN PGP SIGNATURE-----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=hH50
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull more arm64 updates from Catalin Marinas:
- fix W+X page (mark RO) allocated by the arm64 kprobes code
- Makefile fix for .i files in out of tree modules
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: kprobe: make page to RO mode when allocate it
arm64: kdump: fix small typo
arm64: makefile fix build of .i file in external module case
-----BEGIN PGP SIGNATURE-----
iQGzBAABCgAdFiEE6fsu8pdIjtWE/DpLiiy9cAdyT1EFAlvdEHkACgkQiiy9cAdy
T1ERqgwAoaYkwZhee/73MxC5N2JnBpRjP8Wwu6jo7q89DY35zI8NvLfy48VXNmnk
8Sp+zPWXxFgFLxBIGIOEwvfrT2kl84lFHprAAkZRKQcz5ZdeqIgoKYWw46Ezglxn
pyBpGFKNVKVSb0ZbAJgswB0KTCSqW2Hx6mf/lGxx1c2ao1kyXrvN4J2v9bK2UCbV
KC9xAgkkteypiTsB/afWQMAybDtran1TdOS7rm4aNT697KJ4jOPSQ7Bhh4CxT+UC
xSFtobCc/v42Si3oq0DNmFNQOdfj40Tg3RjHRHBOmcqN2b+kmGa/4mCUbVsFL08G
8gpeAHpRDnVwBAQsa6y5LuojOQ0szJzkyM9SZHTyCG3sQRGX3b6L+CYafobzrxnk
81Z0PtnDNvaoqG/6th/cQX/vz9LoiO5KG2dF1c9z+mK4m4D7JObuxaqcsrpb0uZl
fWn8AU900QOP/MrciWhj3II+pyYOV3iqKp0cpUgrP1a2P/Qxu3FkXGc4he/lWfKB
vSXGXf88
=Ilu6
-----END PGP SIGNATURE-----
Merge tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6
Pull cifs fixes and updates from Steve French:
"Three small fixes (one Kerberos related, one for stable, and another
fixes an oops in xfstest 377), two helpful debugging improvements,
three patches for cifs directio and some minor cleanup"
* tag '4.20-rc1-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix signed/unsigned mismatch on aio_read patch
cifs: don't dereference smb_file_target before null check
CIFS: Add direct I/O functions to file_operations
CIFS: Add support for direct I/O write
CIFS: Add support for direct I/O read
smb3: missing defines and structs for reparse point handling
smb3: allow more detailed protocol info on open files for debugging
smb3: on kerberos mount if server doesn't specify auth type use krb5
smb3: add trace point for tree connection
cifs: fix spelling mistake, EACCESS -> EACCES
cifs: fix return value for cifs_listxattr
Julian Wiedmann says:
====================
s390/qeth: fixes 2018-11-02
please apply one round of qeth fixes for -net.
Patch 1 is rather large and removes a use-after-free hazard from many of our
debug trace entries.
Patch 2 is yet another fix-up for the L3 subdriver's new IP address management
code.
Patch 3 and 4 resolve some fallout from the recent changes wrt how/when qeth
allocates its net_device.
Patch 5 makes sure we don't set reserved bits when building HW commands from
user-provided data.
And finally, patch 6 allows ethtool to play nice with new HW.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the various identifiers for 25Gbit cards, and wires them up
into sysfs and ethtool.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ARP_{ADD,REMOVE}_ENTRY cmd structs contain reserved fields.
Introduce a common helper that doesn't raw-copy the user-provided data
into the cmd, but only sets those fields that are strictly needed for
the command.
This also sets the correct command length for ARP_REMOVE_ENTRY.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the carrier 'on' for an unregistered netdevice doesn't update
its operstate. Fix this by delaying the update until the netdevice has
been registered.
Fixes: 91cc98f51e ("s390/qeth: remove duplicated carrier state tracking")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qeth only registers its netdevice when the qeth device is first set
online. Thus a device that has never been set online will trigger
a WARN ("network todo 'hsi%d' but state 0") in unregister_netdev() when
removed.
Fix this by protecting the unregister step, just like we already protect
against repeated registering of the netdevice.
Fixes: d3d1b205e8 ("s390/qeth: allocate netdevice early")
Reported-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sniffing mode for L3 HiperSockets requires that no IP addresses are
registered with the HW. The preferred way to achieve this is for
userspace to delete all the IPs on the interface. But qeth is expected
to also tolerate a configuration where that is not the case, by skipping
the IP registration when in sniffer mode.
Since commit 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
reworked the IP registration logic in the L3 subdriver, this no longer
works. When the qeth device is set online, qeth_l3_recover_ip() now
unconditionally registers all unicast addresses from our internal
IP table.
While we could fix this particular problem by skipping
qeth_l3_recover_ip() on a sniffer device, the more future-proof change
is to skip the IP address registration at the lowest level. This way we
a) catch any future code path that attempts to register an IP address
without considering the sniffer scenario, and
b) continue to build up our internal IP table, so that if sniffer mode
is switched off later we can operate just like normal.
Fixes: 5f78e29cee ("qeth: optimize IP handling in rx_mode callback")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Documentation/s390/s390dbf.txt states quite clearly, using any
pointer in sprinf-formatted s390dbf debug entries is dangerous.
The pointers are dereferenced whenever the trace file is read from.
So if the referenced data has a shorter life-time than the trace file,
any read operation can result in a use-after-free.
So rip out all hazardous use of indirect data, and replace any usage of
dev_name() and such by the Bus ID number.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull 9p fix from Al Viro:
"Regression fix for net/9p handling of iov_iter; broken by braino when
switching to iov_iter_is_kvec() et.al., spotted and fixed by Marc"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
iov_iter: Fix 9p virtio breakage
This is a set of minor small (and safe changes) that didn't make the
initial pull request plus some bug fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW9zD2CYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishaMPAQDwYDbt
wsCd4SlAPz1PzAV25GL3zeBpk5UeCjv2/nIzEgEA6P+poJC85aVznrjNQ2kUyWdS
h/NrvG9UJmvVngKpDWQ=
=FHI8
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is a set of minor small (and safe changes) that didn't make the
initial pull request plus some bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: mvsas: Remove set but not used variable 'id'
scsi: qla2xxx: Remove two arguments from qlafx00_error_entry()
scsi: qla2xxx: Make sure that qlafx00_ioctl_iosb_entry() initializes 'res'
scsi: qla2xxx: Remove a set-but-not-used variable
scsi: qla2xxx: Make qla2x00_sysfs_write_nvram() easier to analyze
scsi: qla2xxx: Declare local functions 'static'
scsi: qla2xxx: Improve several kernel-doc headers
scsi: qla2xxx: Modify fall-through annotations
scsi: 3w-sas: 3w-9xxx: Use unsigned char for cdb
scsi: mvsas: Use dma_pool_zalloc
scsi: target: Don't request modules that aren't even built
scsi: target: Set response length for REPORT TARGET PORT GROUPS
Merge more updates from Andrew Morton:
- more ocfs2 work
- various leftovers
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
memory_hotplug: cond_resched in __remove_pages
bfs: add sanity check at bfs_fill_super()
kernel/sysctl.c: remove duplicated include
kernel/kexec_file.c: remove some duplicated includes
mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask
ocfs2: fix clusters leak in ocfs2_defrag_extent()
ocfs2: dlmglue: clean up timestamp handling
ocfs2: don't put and assigning null to bh allocated outside
ocfs2: fix a misuse a of brelse after failing ocfs2_check_dir_entry
ocfs2: don't use iocb when EIOCBQUEUED returns
ocfs2: without quota support, avoid calling quota recovery
ocfs2: remove ocfs2_is_o2cb_active()
mm: thp: relax __GFP_THISNODE for MADV_HUGEPAGE mappings
include/linux/notifier.h: SRCU: fix ctags
mm: handle no memcg case in memcg_kmem_charge() properly
We have received a bug report that unbinding a large pmem (>1TB) can
result in a soft lockup:
NMI watchdog: BUG: soft lockup - CPU#9 stuck for 23s! [ndctl:4365]
[...]
Supported: Yes
CPU: 9 PID: 4365 Comm: ndctl Not tainted 4.12.14-94.40-default #1 SLE12-SP4
Hardware name: Intel Corporation S2600WFD/S2600WFD, BIOS SE5C620.86B.01.00.0833.051120182255 05/11/2018
task: ffff9cce7d4410c0 task.stack: ffffbe9eb1bc4000
RIP: 0010:__put_page+0x62/0x80
Call Trace:
devm_memremap_pages_release+0x152/0x260
release_nodes+0x18d/0x1d0
device_release_driver_internal+0x160/0x210
unbind_store+0xb3/0xe0
kernfs_fop_write+0x102/0x180
__vfs_write+0x26/0x150
vfs_write+0xad/0x1a0
SyS_write+0x42/0x90
do_syscall_64+0x74/0x150
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x7fd13166b3d0
It has been reported on an older (4.12) kernel but the current upstream
code doesn't cond_resched in the hot remove code at all and the given
range to remove might be really large. Fix the issue by calling
cond_resched once per memory section.
Link: http://lkml.kernel.org/r/20181031125840.23982-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Dan Williams <dan.j.williams@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
syzbot is reporting too large memory allocation at bfs_fill_super() [1].
Since file system image is corrupted such that bfs_sb->s_start == 0,
bfs_fill_super() is trying to allocate 8MB of continuous memory. Fix
this by adding a sanity check on bfs_sb->s_start, __GFP_NOWARN and
printf().
[1] https://syzkaller.appspot.com/bug?id=16a87c236b951351374a84c8a32f40edbc034e96
Link: http://lkml.kernel.org/r/1525862104-3407-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-by: syzbot <syzbot+71c6b5d68e91149fc8a4@syzkaller.appspotmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Tigran Aivazian <aivazian.tigran@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove one include of <linux/pipe_fs_i.h>.
No functional changes.
Link: http://lkml.kernel.org/r/20181004134223.17735-1-michael@schupikov.de
Signed-off-by: Michael Schupikov <michael@schupikov.de>
Reviewed-by: Richard Weinberger <richard@nod.at>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
