This reverts commit 6732491243045f5a7e1995b4be5f3c964b579ebd.
The former commit adds some alternative tracepoints events to replace the
reverted kernel log messages.
Link: https://lore.kernel.org/r/20240501073238.72769-5-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
At a commit 673249124304 ("firewire: core: option to log bus reset
initiation"), some kernel log messages were added to trace initiation of
bus reset. The kernel log messages are really helpful, while nowadays it
is not preferable just for debugging purpose. For the purpose, Linux
kernel tracepoints is more preferable.
This commit adds some alternative tracepoints events.
Link: https://lore.kernel.org/r/20240501073238.72769-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Add a debug parameter to firewire-core, analogous to the one in
firewire-ohci. When this is set to 1, log when we schedule, delay, or
initiate a bus reset. Since FireWire bus resets can originate from any
node on the bus, specific logging of the resets we initiate provides
additional insight.
Signed-off-by: Adam Goldman <adamg@pobox.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
When resetting the bus after a gap count error, use a long rather than
short bus reset.
IEEE 1394-1995 uses only long bus resets. IEEE 1394a adds the option of
short bus resets. When video or audio transmission is in progress and a
device is hot-plugged elsewhere on the bus, the resulting bus reset can
cause video frame drops or audio dropouts. Short bus resets reduce or
eliminate this problem. Accordingly, short bus resets are almost always
preferred.
However, on a mixed 1394/1394a bus, a short bus reset can trigger an
immediate additional bus reset. This double bus reset can be interpreted
differently by different nodes on the bus, resulting in an inconsistent gap
count after the bus reset. An inconsistent gap count will cause another bus
reset, leading to a neverending bus reset loop. This only happens for some
bus topologies, not for all mixed 1394/1394a buses.
By instead sending a long bus reset after a gap count inconsistency, we
avoid the doubled bus reset, restoring the bus to normal operation.
Signed-off-by: Adam Goldman <adamg@pobox.com>
Link: https://sourceforge.net/p/linux1394/mailman/message/58741624/
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
If we are bus manager and the bus has inconsistent gap counts, send a
bus reset immediately instead of trying to read the root node's config
ROM first. Otherwise, we could spend a lot of time trying to read the
config ROM but never succeeding.
This eliminates a 50+ second delay before the FireWire bus is usable after
a newly connected device is powered on in certain circumstances.
The delay occurs if a gap count inconsistency occurs, we are not the root
node, and we become bus manager. One scenario that causes this is with a TI
XIO2213B OHCI, the first time a Sony DSR-25 is powered on after being
connected to the FireWire cable. In this configuration, the Linux box will
not receive the initial PHY configuration packet sent by the DSR-25 as IRM,
resulting in the DSR-25 having a gap count of 44 while the Linux box has a
gap count of 63.
FireWire devices have a gap count parameter, which is set to 63 on power-up
and can be changed with a PHY configuration packet. This determines the
duration of the subaction and arbitration gaps. For reliable communication,
all nodes on a FireWire bus must have the same gap count.
A node may have zero or more of the following roles: root node, bus manager
(BM), isochronous resource manager (IRM), and cycle master. Unless a root
node was forced with a PHY configuration packet, any node might become root
node after a bus reset. Only the root node can become cycle master. If the
root node is not cycle master capable, the BM or IRM should force a change
of root node.
After a bus reset, each node sends a self-ID packet, which contains its
current gap count. A single bus reset does not change the gap count, but
two bus resets in a row will set the gap count to 63. Because a consistent
gap count is required for reliable communication, IEEE 1394a-2000 requires
that the bus manager generate a bus reset if it detects that the gap count
is inconsistent.
When the gap count is inconsistent, build_tree() will notice this after the
self identification process. It will set card->gap_count to the invalid
value 0. If we become bus master, this will force bm_work() to send a bus
reset when it performs gap count optimization.
After a bus reset, there is no bus manager. We will almost always try to
become bus manager. Once we become bus manager, we will first determine
whether the root node is cycle master capable. Then, we will determine if
the gap count should be changed. If either the root node or the gap count
should be changed, we will generate a bus reset.
To determine if the root node is cycle master capable, we read its
configuration ROM. bm_work() will wait until we have finished trying to
read the configuration ROM.
However, an inconsistent gap count can make this take a long time.
read_config_rom() will read the first few quadlets from the config ROM. Due
to the gap count inconsistency, eventually one of the reads will time out.
When read_config_rom() fails, fw_device_init() calls it again until
MAX_RETRIES is reached. This takes 50+ seconds.
Once we give up trying to read the configuration ROM, bm_work() will wake
up, assume that the root node is not cycle master capable, and do a bus
reset. Hopefully, this will resolve the gap count inconsistency.
This change makes bm_work() check for an inconsistent gap count before
waiting for the root node's configuration ROM. If the gap count is
inconsistent, bm_work() will immediately do a bus reset. This eliminates
the 50+ second delay and rapidly brings the bus to a working state.
I considered that if the gap count is inconsistent, a PHY configuration
packet might not be successful, so it could be desirable to skip the PHY
configuration packet before the bus reset in this case. However, IEEE
1394a-2000 and IEEE 1394-2008 say that the bus manager may transmit a PHY
configuration packet before a bus reset when correcting a gap count error.
Since the standard endorses this, I decided it's safe to retain the PHY
configuration packet transmission.
Normally, after a topology change, we will reset the bus a maximum of 5
times to change the root node and perform gap count optimization. However,
if there is a gap count inconsistency, we must always generate a bus reset.
Otherwise the gap count inconsistency will persist and communication will
be unreliable. For that reason, if there is a gap count inconstency, we
generate a bus reset even if we already reached the 5 reset limit.
Signed-off-by: Adam Goldman <adamg@pobox.com>
Reference: https://sourceforge.net/p/linux1394/mailman/message/58727806/
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
card->local_node and card->bm_retries are both always accessed under
card->lock.
fw_core_handle_bus_reset has a check whose condition depends on
card->local_node and whose body writes to card->bm_retries.
Both of these accesses are not under card->lock. Move the lock acquiring
of card->lock to before this check such that these accesses do happen
when card->lock is held.
fw_destroy_nodes is called inside the check.
Since fw_destroy_nodes already acquires card->lock inside its function
body, move this out to the callsites of fw_destroy_nodes.
Also add a comment to indicate which locking is necessary when calling
fw_destroy_nodes.
Cc: <stable@vger.kernel.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220409041243.603210-4-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
1394 OHCI specification defined Isochronous Cycle Timer Register to get
value of CYCLE_TIME register defined by IEEE 1394 for CSR architecture
defined by ISO/IEC 13213. Unit driver can calculate packet time by
compute with the value of CYCLE_TIME and timeStamp field in descriptor
of each isochronous and asynchronous context. The resolution of CYCLE_TIME
is 49.576 MHz, while the one of timeStamp is 8,000 Hz.
Current implementation of Linux FireWire subsystem allows the driver to
get the value of CYCLE_TIMER CSR register by transaction service. The
transaction service has overhead in regard of access to MMIO register.
This commit adds kernel API for unit driver to access the register
directly.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220405072221.226217-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
(Hector Martin wrote)
This fixes segfaults when a card gets yanked off of the PCIe bus while
busy, e.g. with a userspace app trying to get the cycle time:
[8638860.994310] Call Trace:
[8638860.994313] ioctl_get_cycle_timer2+0x4f/0xd0 [firewire_core]
[8638860.994323] fw_device_op_ioctl+0xae/0x150 [firewire_core]
[8638860.994328] __x64_sys_ioctl+0x7d/0xb0
[8638860.994332] do_syscall_64+0x45/0x80
[8638860.994337] entry_SYSCALL_64_after_hwframe+0x44/0xae
(Takashi Sakamoto wrote)
As long as reading commit 2080222429 ("firewire: core: add forgotten
dummy driver methods, remove unused ones"), three functions are not
implemeted in dummy driver for reason; .read_csr, .write_csr, and
.set_config_rom.
In core of Linux FireWire subsystem, the callback of .set_config_rom is
under acquisition of mutual exclusive for local list of card. The
acquision is also done in process for removal of card, therefore it's
safe for missing implementation of .set_config_rom.
On the other hand, no lock primitive accompanies any call of .read_csr and
.write_csr. For userspace client, check of node shutdown is done in the
beginning of dispatch of ioctl request, while node shifts to shutdown
state in workqueue context enough after card shifts to dummy driver. It's
probable that these two functions are called for the dummy driver by the
code of userspace client. In-kernel unit driver has similar situation.
It's better to add implementation of the two functions for dummy driver.
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20220405072221.226217-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix mismatch between DMA mapping direction (was wrong) and DMA synchronization
direction (was correct) of isochronous reception buffers of userspace drivers
if vma-mapped for R/W access. For example, libdc1394 was affected.
- more consistent retry stategy in device discovery/ rediscovery, and improved
failure diagnostics
- various small cleanups, e.g. use SCSI layer's DMA mapping API in firewire-sbp2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=fulr
-----END PGP SIGNATURE-----
Merge tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394
Pull IEEE 1394 (FireWire) subsystem updates from Stefan Richter:
- Fix mismatch between DMA mapping direction (was wrong) and DMA
synchronization direction (was correct) of isochronous reception
buffers of userspace drivers if vma-mapped for R/W access. For
example, libdc1394 was affected.
- more consistent retry stategy in device discovery/ rediscovery, and
improved failure diagnostics
- various small cleanups, e.g. use SCSI layer's DMA mapping API in
firewire-sbp2
* tag 'firewire-updates' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
firewire: sbp2: document the absence of alignment requirements
firewire: sbp2: remove superfluous blk_queue_max_segment_size() call
firewire: sbp2: use scsi_dma_(un)map
firewire: sbp2: give correct DMA device to scsi framework
firewire: core: fw_device_refresh(): clean up error handling
firewire: core: log config rom reading errors
firewire: core: log error in case of failed bus manager lock
firewire: move rcode_string() to core
firewire: core: improve reread_config_rom() interface
firewire: core: wait for inaccessible devices after bus reset
firewire: ohci: omit spinlock IRQ flags where possible
firewire: ohci: correct signedness of a local variable
firewire: core: fix DMA mapping direction
firewire: use module_pci_driver
When writing a firewire driver that doesn't deal with struct fw_device
objects (e.g. it only publishes FireWire units and doesn't subscribe to
them), you likely need to keep referenced to struct fw_card objects so
that you can send messages to other nodes. This patch moves
fw_card_put(), fw_card_get() and fw_card_release() into the public
include/linux/firewire.h header instead of drivers/firewire/core.h, and
adds EXPORT_SYMBOL_GPL(fw_card_release).
The firewire-sbp-target module requires these so it can keep a reference
to the fw_card object in order that it can fetch ORBs to execute and
read/write related data and status information.
Signed-off-by: Chris Boot <bootc@bootc.net>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
If the lock access to the bus manager register fails, also log the
actual error that caused it to fail.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Extend the kernel and userspace APIs to allow reporting all currently
completed isochronous packets, even if the next interrupt packet has not
yet been reached. This is required to determine the status of the
packets at the end of a paused or stopped stream, and useful for more
precise synchronization of audio streams.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Associate all log messages from firewire-core with the respective card
because some people have more than one card. E.g.
firewire_ohci 0000:04:00.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
firewire_ohci 0000:05:00.0: added OHCI v1.10 device as card 1, 8 IR + 8 IT contexts, quirks 0x0
firewire_core: created device fw0: GUID 0814438400000389, S800
firewire_core: phy config: new root=ffc1, gap_count=5
firewire_core: created device fw1: GUID 0814438400000388, S800
firewire_core: created device fw2: GUID 0001d202e06800d1, S800
turns into
firewire_ohci 0000:04:00.0: added OHCI v1.10 device as card 0, 8 IR + 8 IT contexts, quirks 0x0
firewire_ohci 0000:05:00.0: added OHCI v1.10 device as card 1, 8 IR + 8 IT contexts, quirks 0x0
firewire_core 0000:04:00.0: created device fw0: GUID 0814438400000389, S800
firewire_core 0000:04:00.0: phy config: new root=ffc1, gap_count=5
firewire_core 0000:05:00.0: created device fw1: GUID 0814438400000388, S800
firewire_core 0000:04:00.0: created device fw2: GUID 0001d202e06800d1, S800
This increases the module size slightly; to keep this in check, turn the
former printk wrapper macros into functions. Their implementation is
largely copied from driver core's dev_printk counterparts.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The struct sbp2_logical_unit.work items can all be executed in parallel
but are not reentrant. Furthermore, reconnect or re-login work must be
executed in a WQ_MEM_RECLAIM workqueue.
Hence replace the old single-threaded firewire-sbp2 workqueue by a
concurrency-managed but non-reentrant workqueue with rescuer.
firewire-core already maintains one, hence use this one.
In earlier versions of this change, I observed occasional failures of
parallel INQUIRY to an Initio INIC-2430 FireWire 800 to dual IDE bridge.
More testing indicates that parallel INQUIRY is not actually a problem,
but too quick successions of logout and login + INQUIRY, e.g. a quick
sequence of cable plugout and plugin, can result in failed INQUIRY.
This does not seem to be something that should or could be addressed by
serialization.
Another dual-LU device to which I currently have access to, an
OXUF924DSB FireWire 800 to dual SATA bridge with firmware from MacPower,
has been successfully tested with this too.
This change is beneficial to environments with two or more FireWire
storage devices, especially if they are located on the same bus.
Management tasks that should be performed as soon and as quickly as
possible, especially reconnect, are no longer held up by tasks on other
devices that may take a long time, especially login with INQUIRY and sd
or sr driver probe.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
firewire-core manages the following types of work items:
fw_card.br_work:
- resets the bus on a card and possibly sends a PHY packet before that
- does not sleep for long or not at all
- is scheduled via fw_schedule_bus_reset() by
- firewire-ohci's pci_probe method
- firewire-ohci's set_config_rom method, called by kernelspace
protocol drivers and userspace drivers which add/remove
Configuration ROM descriptors
- userspace drivers which use the bus reset ioctl
- itself if the last reset happened less than 2 seconds ago
fw_card.bm_work:
- performs bus management duties
- usually does not (but may in corner cases) sleep for long
- is scheduled via fw_schedule_bm_work() by
- firewire-ohci's self-ID-complete IRQ handler tasklet
- firewire-core's fw_device.work instances whenever the root node
device was (successfully or unsuccessfully) discovered,
refreshed, or rediscovered
- itself in case of resource allocation failures or in order to
obey the 125ms bus manager arbitration interval
fw_device.work:
- performs node probe, update, shutdown, revival, removal; including
kernel driver probe, update, shutdown and bus reset notification to
userspace drivers
- usually sleeps moderately long, in corner cases very long
- is scheduled by
- firewire-ohci's self-ID-complete IRQ handler tasklet via the
core's fw_node_event
- firewire-ohci's pci_remove method via core's fw_destroy_nodes/
fw_node_event
- itself during retries, e.g. while a node is powering up
iso_resource.work:
- accesses registers at the Isochronous Resource Manager node
- usually does not (but may in corner cases) sleep for long
- is scheduled via schedule_iso_resource() by
- the owning userspace driver at addition and removal of the
resource
- firewire-core's fw_device.work instances after bus reset
- itself in case of resource allocation if necessary to obey the
1000ms reallocation period after bus reset
fw_card.br_work instances should not, and instances of the others must
not, be executed in parallel by multiple CPUs -- but were not protected
against that. Hence allocate a non-reentrant workqueue for them.
fw_device.work may be used in the memory reclaim path in case of SBP-2
device updates. Hence we need a workqueue with rescuer and cannot use
system_nrt_wq.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reviewed-by: Tejun Heo <tj@kernel.org>
When queueing iso packets, the run time is dominated by the two
MMIO accesses that set the DMA context's wake bit. Because most
drivers submit packets in batches, we can save much time by
removing all but the last wakeup.
The internal kernel API is changed to require a call to
fw_iso_context_queue_flush() after a batch of queued packets.
The user space API does not change, so one call to
FW_CDEV_IOC_QUEUE_ISO must specify multiple packets to take
advantage of this optimization.
In my measurements, this patch reduces the time needed to queue
fifty skip packets from userspace to one sixth on a 2.5 GHz CPU,
or to one third at 800 MHz.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
We do not need slab allocations anymore in order to satisfy
streaming DMA mapping constraints, thanks to commit da28947e7e
"firewire: ohci: avoid separate DMA mapping for small AT payloads".
(Besides, the slab-allocated buffers that firewire-core, firewire-sbp2,
and firedtv used to provide for 8-byte write and lock requests were
still not fully portable since they crossed cacheline boundaries or
shared a cacheline with unrelated CPU-accessed data. snd-firewire-lib
got this aspect right by using an extra kmalloc/ kfree just for the
8-byte transaction buffer.)
This change replaces kmalloc'ed lock transaction scratch buffers in
firewire-core, firedtv, and snd-firewire-lib by local stack allocations.
Perhaps the most notable result of the change is simpler locking because
there is no need to serialize usages of preallocated per-device buffers
anymore. Also, allocations and deallocations are simpler.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
The SPLIT_TIMEOUT mechanism is intended to detect requests that somehow
got lost. However, when the timeout value is too low, transactions that
could have been completed successfully will be cancelled. Furthermore,
there are chips whose firmwares ignore the configured split timeout and
send late split response; known examples are the DM1x00 (BeBoB), TCD22x0
(DICE), and some OXUF936QSE firmwares.
This patch changes the default timeout to two seconds, which happens to
be the default on other OSes, too.
Actual lost requests are extremely rare, so there should be no practical
downside to increasing the split timeout even on devices that work
correctly.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
On a 32-bit machine with, e.g., HZ=1000, jiffies will overflow after
about 50 days, so if there are between 25 and 50 days between bus
resets, the card->reset_jiffies comparisons can get wrong results.
To fix this, ensure that this timestamp always uses 64 bits.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: "Stefan Richter" <stefanr@s5r6.in-berlin.de>
Regression since commit 1038953674, "firewire: core: check for 1394a
compliant IRM, fix inaccessibility of Sony camcorder":
The camcorder Canon MV5i generates lots of bus resets when asynchronous
requests are sent to it (e.g. Config ROM read requests or FCP Command
write requests) if the camcorder is not root node. This causes drop-
outs in videos or makes the camcorder entirely inaccessible.
https://bugzilla.redhat.com/show_bug.cgi?id=633260
Fix this by allowing any Canon device, even if it is a pre-1394a IRM
like MV5i are, to remain root node (if it is at least Cycle Master
capable). With the FireWire controller cards that I tested, MV5i always
becomes root node when plugged in and left to its own devices.
Reported-by: Ralf Lange
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org> # 2.6.32.y and newer
Conflicts:
drivers/firewire/core-card.c
drivers/firewire/core-cdev.c
and forgotten #include <linux/time.h> in drivers/firewire/ohci.c
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
There is an at least theoretic race condition in which .start_iso etc.
could still be called between when the dummy driver is bound to the card
and when the children devices are being shut down. Add dummy_start_iso
and friends.
On the other hand, .enable, .set_config_rom, .read_csr, write_csr do not
need to be implemented by the dummy driver, as commented.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add an FW_CDEV_IOC_RECEIVE_PHY_PACKETS ioctl() and
FW_CDEV_EVENT_PHY_PACKET_RECEIVED poll()/read() event for /dev/fw*.
This can be used to get information from remote PHYs by remote access
PHY packets.
This is also the 2nd half of the functionality (the receive part) to
support a userspace implementation of a VersaPHY transaction layer.
Safety considerations:
- PHY packets are generally broadcasts, hence some kind of elevated
privileges should be required of a process to be able to listen in
on PHY packets. This implementation assumes that a process that is
allowed to open the /dev/fw* of a local node does have this
privilege.
There was an inconclusive discussion about introducing POSIX
capabilities as a means to check for user privileges for these
kinds of operations.
Other limitations:
- PHY packet reception may be switched on by ioctl() but cannot be
switched off again. It would be trivial to provide an off switch,
but this is not worth the code. The client should simply close()
the fd then, or just ignore further events.
- For sake of simplicity of API and kernel-side implementation, no
filter per packet content is provided.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
core-transaction.c transmit_complete_callback() and close_transaction()
expect packet callback status to be an ACK or RCODE, and ACKs get
translated to RCODEs for transaction callbacks.
An old comment on the packet callback API (been there from the initial
submission of the stack) and the dummy_driver implementation of
send_request/send_response deviated from this as they also included
-ERRNO in the range of status values.
Let's narrow status values down to ACK and RCODE to prevent surprises.
RCODE_CANCELLED is chosen as the dummy_driver's RCODE as its meaning of
"transaction timed out" comes closest to what happens when a transaction
coincides with card removal.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Bus resets which are triggered
- by the kernel drivers after updates of the local nodes' config ROM,
- by userspace software via ioctl
shall be deferred until after >=2 seconds after the last bus reset.
If multiple modifications of the local nodes' config ROM happen in a row,
only a single bus reset should happen after them.
When the local node's link goes from inactive to active or vice versa,
and at the two occasions of bus resets mentioned above --- and if the
current gap count differs from 63 --- the bus reset should be preceded
by a PHY configuration packet that reaffirms the gap count. Otherwise a
bus manager would have to reset the bus again right after that.
This is necessary to promote bus stability, e.g. leave grace periods for
allocations and reallocations of isochronous channels and bandwidth,
SBP-2 reconnections etc.; see IEEE 1394 clause 8.2.1.
This change implements all of the above by moving bus reset initiation
into a delayed work (except for bus resets which are triggered by the
bus manager workqueue job and are performed there immediately). It
comes with a necessary addition to the card driver methods that allows
to get the current gap count from PHY registers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix an obscure ABI feature that is a bit of a hassle to implement.
However, somebody put it into the ABI, so let's fill in a sensible
value there.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In case of fw_card_bm_work()'s lock request, the present sizeof
expression is going to be wrong if somebody changes the fw_card's DMA
scratch buffer's size in the future.
In case of quadlet write requests, sizeof(u32) is just silly; it's 4.
In case of SBP-2 ORB pointer write requests, 8 is arguably quicker to
understand as the correct and only possible value than
sizeof(some_datum).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
As part of the bus manager responsibilities, make sure that the cycle
master sends cycle start packets. This is needed when the old bus
manager disabled the cycle master's cmstr bit and there are iso-capable
nodes on the new bus.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
On OHCI 1.1 controllers, let the hardware allocate the broadcast channel
automatically. This removes a theoretical race condition directly after
a bus reset where it could be possible to read the channel allocation
register with channel 31 still being unallocated.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Implement the abdicate bit, which is required for bus manager
capable nodes and tested by the Base 1394 Test Suite.
Finally, something to do at a command reset! :-)
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Implement the SPLIT_TIMEOUT registers. Besides being required by the
spec, this is desirable for some IIDC devices and necessary for many
audio devices to be able to increase the timeout from userspace.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
When the candidate bus manager fails to do the lock request with which
it tries to become bus manager, it assumes that the current IRM is not
actually IRM capable and forces itself to become root. However, if that
lock request failed because the local node itself was not able to send
it, then we cannot blame the current IRM and should not steal its
rootness.
In this case, RCODE_SEND_ERROR is likely to indicate a temporary error
condition such as exhausted tlabels or low memory, so we better try
again later.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Per IEEE 1394 clause 8.4.2.3, a contender for the IRM role shall check
whether the current IRM complies to 1394a-2000 or later. If not force a
compliant node (e.g. itself) to become IRM. This was implemented in the
older ieee1394 driver but not yet in firewire-core.
An older Sony camcorder (Sony DCR-TRV25) which implements 1394-1995 IRM
but neither 1394a-2000 IRM nor BM was now found to cause an
interoperability bug:
- Camcorder becomes root node when plugged in, hence gets IRM role.
- firewire-core successfully contends for BM role, proceeds to perform
gap count optimization and resets the bus.
- Sony camcorder ignores presence of a BM (against the spec, this is
a firmware bug), performs its idea of gap count optimization and
resets the bus.
- Preceding two steps are repeated endlessly, bus never settles,
regular I/O is practically impossible.
http://thread.gmane.org/gmane.linux.kernel.firewire.user/3913
This is an interoperability regression from the old to the new drivers.
Fix it indirectly by adding the 1394a IRM check. The spec suggests
three and a half methods to determine 1394a compliance of a remote IRM;
we choose the method of testing the Config_ROM.Bus_Info.generation
field. This is data that firewire-core should have readily available at
this point, i.e. does not require extra I/O.
Reported-by: Clemens Ladisch <clemens@ladisch.de> (missing 1394a check)
Reported-by: H. S. <hs.samix@gmail.com> (issue with Sony DCR-TRV25)
Tested-by: H. S. <hs.samix@gmail.com>
Cc: <stable@kernel.org> # .32.x and newer
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Using a single timeout for all transaction that need to be flushed does
not work if the submission of new transactions can defer the timeout
indefinitely into the future. We need to have timeouts that do not
change due to other transactions; the simplest way to do this is with a
separate timer for each transaction.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (+ one lockdep annotation)
Clemens Ladisch pointed out that
- BIB_IMC is not named like the field is called in the standard,
- readers of the code may get worried about the magic 0x0c0083c0,
- a CSR_NODE_CAPABILITIES key is there in the header but not put to
good use.
So let's rename BIB_IMC, add a defined constant for Node_Capabilities
and a comment which reassures people that somebody thought about it and
they don't have to (or if they still do, tell them where they have to
look for confirmation), and prune our incomplete and arbitrary set of
defined constants of CSR key IDs. And there is a nother magic number,
that of Bus_Information_Block.Bus_Name, to be defined and commented.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Presently, firewire-core only checks whether descriptors that are to be
added by userspace drivers to the local node's config ROM do not exceed
a size of 256 quadlets. However, the sum of the bare minimum ROM plus
all descriptors (from firewire-core, from firewire-net, from userspace)
must not exceed 256 quadlets.
Otherwise, the bounds of a statically allocated buffer will be
overwritten. If the kernel survives that, firewire-core will
subsequently be unable to parse the local node's config ROM.
(Note, userspace drivers can add descriptors only through device files
of local nodes. These are usually only accessible by root, unlike
device files of remote nodes which may be accessible to lesser
privileged users.)
Therefore add a test which takes the actual present and required ROM
size into account for all descriptors of kernelspace and userspace
drivers.
Cc: stable@kernel.org
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The Topology Map of the local node was created in CPU byte order,
then a temporary big endian copy was created to compute the CRC,
and when a read request to the Topology Map arrived it had to be
converted to big endian byte order again.
We now generate it in big endian byte order in the first place.
This also rids us of 1000 bytes stack usage in tasklet context.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Move the static config ROM buffer into the scope of the two callers of
generate_config_rom(). That way the ROM length can be passed over as
return value rather than through a pointer argument.
It also becomes more obvious that accesses to the config ROM buffer have
to be serialized and how this is accomplished. And firewire-core.ko
shrinks a bit as well.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The config ROM image of the local node was created in CPU byte order,
then a temporary big endian copy was created to compute the CRC, and
finally the card driver created its own big endian copy.
We now generate it in big endian byte order in the first place to avoid
one byte order conversion and the temporary on-stack copy of the ROM
image (1000 bytes stack usage in process context). Furthermore, two
1000 bytes memset()s are replaced by one 1000 bytes - ROM length sized
memset.
The trivial fw_memcpy_{from,to}_be32() helpers are now superfluous and
removed. The newly added __compute_block_crc() function will be folded
into fw_compute_block_crc() in a subsequent change.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
A few stylistic changes to unify some code patterns in the subsystem:
- The similar queue_delayed_work helpers fw_schedule_bm_work,
schedule_iso_resource, and sbp2_queue_work now have the same call
convention.
- Two conditional calls of schedule_iso_resource are factored into
another small helper.
- An sbp2_target_get helper is added as counterpart to
sbp2_target_put.
Object size of firewire-core is decreased a little bit, object size of
firewire-sbp2 remains unchanged.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The config ROM buffer received from generate_config_rom is a globally
shared static buffer. Extend the card_mutex protection in fw_add_card
until after the config ROM was copied into the card driver's buffer.
Otherwise, parallelized card driver probes may end up with ROM contents
that were meant for a different card.
firewire-ohci's card->driver->enable hook is safe to be called within
the card_mutex. Furthermore, it is safe to reorder card_list update
versus card enable, which simplifies the code a little.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The DMA mapping API cannot map on-stack addresses, as explained in
Documentation/DMA-mapping.txt. Convert the two cases of on-stack packet
payload buffers in firewire-core (payload of lock requests in the bus
manager work and in iso resource management) to slab-allocated memory.
There are a number on-stack buffers for quadlet write or quadlet read
requests in firewire-core and firewire-sbp2. These are harmless; they
are copied to/ from card driver internal DMA buffers since quadlet
payloads are inlined with packet headers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
If isochronous contexts existed when firewire-ohci was unloaded, the
core iso shutdown functions crashed with NULL dereferences, and buffers
etc. weren't released.
How the fix works: We first copy the card driver's iso shutdown hooks
into the dummy driver, then fw_destroy_nodes notifies upper layers of
devices going away, these should shut down (including their iso
contexts), wait_for_completion(&card->done) will be triggered after
upper layers gave up all fw_device references, after which the card
driver's shutdown proceeds.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Decouple the creation and destruction of the net_device from the order
of discovery and removal of nodes with RFC 2734 unit directories since
there is no reliable order. The net_device is now created when the
first RFC 2734 unit on a card is discovered, and destroyed when the last
RFC 2734 unit on a card went away. This includes all remote units as
well as the local unit, which is therefore tracked as a peer now too.
Also, locking around the list of peers is slightly extended to guard
against peer removal. As a side effect, fwnet_peer.pdg_lock has become
superfluous and is deleted.
Peer data (max_rec, speed, node ID, generation) are updated more
carefully.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Implement IPv4 over IEEE 1394 as per RFC 2734 for the newer firewire
stack. This feature has only been present in the older ieee1394 stack
via the eth1394 driver.
Still to do:
- fix ipv4_priv and ipv4_node lifetime logic
- fix determination of speeds and max payloads
- fix bus reset handling
- fix unaligned memory accesses
- fix coding style
- further testing/ improvement of fragment reassembly
- perhaps multicast support
Signed-off-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (rebased, copyright note, changelog)
