cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This
was done to avoid having a custom <asm/gpio.h> header for
the x86 architecture - GPIO is custom and complicated
enough as it is already! We want to move to a radix to
store the descriptors going forward, and finally get rid
of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated
by Abdoulaye Berthe. It is not accepted by the system that
the removal of a GPIO chip fails during e.g. reboot or
shutdown, and therefore the return value has now painfully
been refactored away. For special cases like GPIO expanders
on a hot-pluggable bus like USB, we may later add some
gpiochip_try_remove() call, but for the cases we have now,
return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI
GPIO library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle
also threaded, nested interrupts and set up the parent IRQ
correctly. Switch STMPE and TC3589x drivers to use this
registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so
that also GPIO expanders that block but are still not
using threaded IRQ handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the
"DSP GPIO" found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated
from and MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08,
DWAPB, OMAP, Xilinx and Crystalcove drivers.
- Various minor fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8InA
-----END PGP SIGNATURE-----
Merge tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO changes from Linus Walleij:
"This is the bulk of GPIO changes for the v3.18 development cycle:
- Increase the default ARCH_NR_GPIO from 256 to 512. This was done
to avoid having a custom <asm/gpio.h> header for the x86
architecture - GPIO is custom and complicated enough as it is
already! We want to move to a radix to store the descriptors going
forward, and finally get rid of this fixed array size altogether.
- Endgame patching of the gpio_remove() semantics initiated by
Abdoulaye Berthe. It is not accepted by the system that the
removal of a GPIO chip fails during eg reboot or shutdown, and
therefore the return value has now painfully been refactored away.
For special cases like GPIO expanders on a hot-pluggable bus like
USB, we may later add some gpiochip_try_remove() call, but for the
cases we have now, return values are moot.
- Some incremental refactoring of the gpiolib core and ACPI GPIO
library for more descriptor usage.
- Refactor the chained IRQ handler set-up method to handle also
threaded, nested interrupts and set up the parent IRQ correctly.
Switch STMPE and TC3589x drivers to use this registration method.
- Add a .irq_not_threaded flag to the struct gpio_chip, so that also
GPIO expanders that block but are still not using threaded IRQ
handlers.
- New drivers for the ARM64 X-Gene SoC GPIO controller.
- The syscon GPIO driver has been improved to handle the "DSP GPIO"
found on the TI Keystone 2 SoC:s.
- ADNP driver switched to use gpiolib irqchip helpers.
- Refactor the DWAPB driver to support being instantiated from and
MFD cell (platform device).
- Incremental feature improvement in the Zynq, MCP23S08, DWAPB, OMAP,
Xilinx and Crystalcove drivers.
- Various minor fixes"
* tag 'gpio-v3.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (52 commits)
gpio: pch: Build context save/restore only for PM
pinctrl: abx500: get rid of unused variable
gpio: ks8695: fix 'else should follow close brace '}''
gpio: stmpe: add verbose debug code
gpio: stmpe: fix up interrupt enable logic
gpio: staticize xway_stp_init()
gpio: handle also nested irqchips in the chained handler set-up
gpio: set parent irq on chained handlers
gpiolib: irqchip: use irq_find_mapping while removing irqchip
gpio: crystalcove: support virtual GPIO
pinctrl: bcm281xx: make Kconfig dependency more strict
gpio: kona: enable only on BCM_MOBILE or for compile testing
gpio, bcm-kona, LLVMLinux: Remove use of __initconst
gpio: Fix ngpio in gpio-xilinx driver
gpio: dwapb: fix pointer to integer cast
gpio: xgene: Remove unneeded #ifdef CONFIG_OF guard
gpio: xgene: Remove unneeded forward declation for struct xgene_gpio
gpio: xgene: Fix missing spin_lock_init()
gpio: ks8695: fix switch case indentation
gpiolib: add irq_not_threaded flag to gpio_chip
...
This will allow us to define GPIO-attached devices (LEDs, buttons) in
the the device tree.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GPIOs can be also used on bcm53xx, however this arch requires different
implementation of IRQ support. It uses different IRQ number (117) and
different masks & acking.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this remove all reference to gpio_remove retval in all driver
except pinctrl and gpio. the same thing is done for gpio and
pinctrl in two different patches.
Signed-off-by: Abdoulaye Berthe <berthe.ab@gmail.com>
Acked-by: Michael Büsch <m@bues.ch>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I've here a device detected as:
bcma: bus0: Found chip with id 0xD144, rev 0x01 and package 0x08
I couldn't find GPIO handling hw button until trying GPIO 20. It seems
BCM53572 also has 32 GPIOs.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some Broadcom boards have more GPIOs available. For example Linksys
E3200 home router is based on SoC id 0x5357, package 0x0A and uses GPIO
23 to reset internal USB WiFi (gpio23=wombo_reset).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With this patch we prevent the irq from being fired when it is
registered. The Hardware fires an IRQ when input signal XOR polarity
AND gpio mask is 1. Now we are setting polarity to a vlaue so that is
is 0 when we register it.
In addition we also set the irq mask register to 0 when the irq handler
is initialized, so all gpio irqs are masked and there will be no
unexpected irq.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6304/
Input GPIO changes can generate interrupts, but we need kind of ACK for
them by changing IRQ polarity. This is required to stop hardware from
keep generating interrupts and generate another one on the next GPIO
state change.
This code allows using GPIOs with standard interrupts and add for
example GPIO buttons support.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6216/
Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch unregisters the gpio chip before bcma gets unloaded.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old bcm47xx gpio code had support for gpio_to_irq, but the new
code did not provide this function, but returned -ENXIO all the time.
This patch adds the missing function.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Register a GPIO driver to access the GPIOs provided by the chip.
The GPIOs of the SoC should always start at 0 and the other GPIOs could
start at a random position. There is just one SoC in a system and when
they start at 0 the number is predictable.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4587
Acked-by: Florian Fainelli <florian@openwrt.org>
