Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:
In preparation for supporting devices with multiple chip selects add an
interface for accessing the chip selects via a function.
Supporting multi-cs in spi core and spi controller drivers would require
the chip_select & cs_gpiod members of struct spi_device to be an array.
But changing the type of these members to array would break the spi driver
functionality. To make the transition smoother introduced four new APIs to
get/set the spi->chip_select & spi->cs_gpiod and replaced all
spi->chip_select and spi->cs_gpiod references in spi core with the API
calls.
While adding multi-cs support in further patches the chip_select & cs_gpiod
members of the spi_device structure would be converted to arrays & the
"idx" parameter of the APIs would be used as array index i.e.,
spi->chip_select[idx] & spi->cs_gpiod[idx] respectively.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20230119185342.2093323-2-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we support parsing the setup time from the Device Tree, we can
also easily support the remaining hold and inactive time delay values.
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230113102309.18308-4-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
65us is not a reasonable maximum for this property, as some devices
might need a much longer setup time (e.g. those driven by firmware on
the other end). Plus, device tree property values are in 32-bit cells
and smaller widths should not be used without good reason.
Also move the logic to a helper function, since this will later be used
to parse other CS delay properties too.
Fixes: 33a2fde5f7 ("spi: Introduce spi-cs-setup-ns property")
Signed-off-by: Janne Grunau <j@jannau.net>
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230113102309.18308-2-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
As mentioned in the corresponding DT binding commit, the naming scheme
for delay properties includes "delay" in the name, so let's keep that
consistent.
Fixes: 33a2fde5f7 ("spi: Introduce spi-cs-setup-ns property")
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20230104093631.15611-3-marcan@marcan.st
Signed-off-by: Mark Brown <broonie@kernel.org>
commit 4ccf359849 ("spi: remove spi_set_cs_timing()"), removed the
method as noboby used it. Nobody used it probably because some SPI
controllers use some default large cs-setup time that covers the usual
cs-setup time required by the spi devices. There are though SPI controllers
that have a smaller granularity for the cs-setup time and their default
value can't fulfill the spi device requirements. That's the case for the
at91 QSPI IPs where the default cs-setup time is half of the QSPI clock
period. This was observed when using an sst26vf064b SPI NOR flash which
needs a spi-cs-setup-ns = <7>; in order to be operated close to its maximum
104 MHz frequency.
Call spi_set_cs_timing() in spi_setup() just before calling spi_set_cs(),
as the latter needs the CS timings already set.
If spi->controller->set_cs_timing is not set, the method will return 0.
There's no functional impact expected for the existing drivers. Even if the
spi-mt65xx.c and spi-tegra114.c drivers set the set_cs_timing method,
there's no user for them as of now. The only tested user of this support
will be a SPI NOR flash that comunicates with the Atmel QSPI controller for
which the support follows in the next patches.
One will notice that this support is a bit different from the one that was
removed in commit 4ccf359849 ("spi: remove spi_set_cs_timing()"),
because this patch adapts to the changes done after the removal: the move
of the cs delays to the spi device, the retirement of the lelgacy GPIO
handling. The mutex handling was removed from spi_set_cs_timing() because
we now always call spi_set_cs_timing() in spi_setup(), which already
handles the spi->controller->io_mutex, so use the mutex handling from
spi_setup().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-4-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SPI NOR flashes have specific cs-setup time requirements without which
they can't work at frequencies close to their maximum supported frequency,
as they miss the first bits of the instruction command. Unrecognized
commands are ignored, thus the flash will be unresponsive. Introduce the
spi-cs-setup-ns property to allow spi devices to specify their cs setup
time.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Link: https://lore.kernel.org/r/20221117105249.115649-3-tudor.ambarus@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
For using modern names host/target to instead of all the legacy names,
I think it takes 3 steps:
- step1: introduce new helpers with modern naming.
- step2: switch to use these new helpers in all drivers.
- step3: remove all legacy helpers and update all legacy names.
This patch is for step1, it introduces new helpers with host/target
naming for drivers using.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20221011092204.950288-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the 32bit UP oddity is gone and 32bit uses always a sequence
count, there is no need for the fetch_irq() variants anymore.
Convert to the regular interface.
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lore.kernel.org/r/20221026122951.331638-1-bigeasy@linutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The proposed spi_get_device_match_data() helper is for retrieving
a driver data associated with the ID in an ID table. First, it tries
to get driver data of the device enumerated by firmware interface
(usually Device Tree or ACPI). If none is found it falls back to
the SPI ID table matching.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221020195421.10482-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With the exception of some refactoring to fix long standing issues
where we weren't handling cache syncs properly for messages which had
PIO and DMA transfers going to the same page correctly there has been o
work on the core this time around, and it's also been quite a quiet
release for the drivers too:
- Fix cache syncs for cases where we have DMA and PIO transfers in the
same message going to the same page.
- Update the fsl_spi driver to use transfer_one() rather than a custom
transfer function.
- Support for configuring transfer speeds with the AMD SPI controller.
- Support for a second chip select and 64K erase on Intel SPI.
- Support for Microchip coreQSPI, Nuvoton NPCM845, NXP i.MX93, and
Rockchip RK3128 and RK3588.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmM62YIACgkQJNaLcl1U
h9CvPAf+MF1AzJJWH9DkR846KQh7Zt1rrujRuj5SGwvHewqjJcDtDmipAbM7mRFa
VPk6fCzfRE4btVywCDMEQX2ToB9VKBNUeP8ihVLddWrTddbkQ7hOKlTrz31dJ+6W
F9kwXkWcqWEpMYD/wr/25eT/kkNfv27oCyPU4dRQKoGGeF+zb9jYoj0+gPDl9Om8
ok7D1XAwY1wOqYqdPfl2thcUrBfoKtFvkTj+NNhqwuzWwIqfQHM2skwAjmD3fliQ
lLdRc54erCOqukDddIoWr348TyJIT4v1IXnkqY3cd7da6+kpixWae73o/7WIcQUR
4MrtPply0WWcapgU/46sCbHpjJNjjg==
=PDCv
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"With the exception of some refactoring to fix long standing issues
where we weren't handling cache syncs properly for messages which had
PIO and DMA transfers going to the same page correctly there has been
no work on the core this time around, and it's also been quite a quiet
release for the drivers too:
- Fix cache syncs for cases where we have DMA and PIO transfers in
the same message going to the same page
- Update the fsl_spi driver to use transfer_one() rather than a
custom transfer function
- Support for configuring transfer speeds with the AMD SPI controller
- Support for a second chip select and 64K erase on Intel SPI
- Support for Microchip coreQSPI, Nuvoton NPCM845, NXP i.MX93, and
Rockchip RK3128 and RK3588"
* tag 'spi-v6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (73 commits)
spi: Ensure that sg_table won't be used after being freed
spi: spi-gxp: Use devm_platform_ioremap_resource()
spi: s3c64xx: Fix large transfers with DMA
spi: Split transfers larger than max size
spi: Fix cache corruption due to DMA/PIO overlap
spi: Save current RX and TX DMA devices
spi: mt65xx: Add dma max segment size declaration
spi: migrate mt7621 text bindings to YAML
spi: renesas,sh-msiof: Add r8a779g0 support
spi: spi-fsl-qspi: Use devm_platform_ioremap_resource_byname()
spi: spi-fsl-lpspi: Use devm_platform_get_and_ioremap_resource()
spi: spi-fsl-dspi: Use devm_platform_get_and_ioremap_resource()
spi/omap100k:Fix PM disable depth imbalance in omap1_spi100k_probe
spi: dw: Fix PM disable depth imbalance in dw_spi_bt1_probe
spi: cadence-quadspi: Fix PM disable depth imbalance in cqspi_probe
spi: s3c24xx: Switch to use devm_spi_alloc_master()
spi: xilinx: Switch to use devm_spi_alloc_master()
spi: img-spfi: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
spi: aspeed: Remove redundant dev_err call
spi: spi-mpc52xx: switch to using gpiod API
...
Merge changes regarding the management of ACPI device objects for
6.1-rc1:
- Rename ACPI device object reference counting functions (Rafael
Wysocki).
- Rearrange ACPI device object initialization code (Rafael Wysocki).
- Drop parent field from struct acpi_device (Rafael Wysocki).
- Extend the the int3472-tps68470 driver to support multiple consumers
of a single TPS68470 along with the requisite framework-level
support (Daniel Scally).
* acpi-dev:
platform/x86: int3472: Add board data for Surface Go2 IR camera
platform/x86: int3472: Support multiple gpio lookups in board data
platform/x86: int3472: Support multiple clock consumers
ACPI: bus: Add iterator for dependent devices
ACPI: scan: Add acpi_dev_get_next_consumer_dev()
ACPI: property: Use acpi_dev_parent()
ACPI: Drop redundant acpi_dev_parent() header
ACPI: PM: Fix NULL argument handling in acpi_device_get/set_power()
ACPI: Drop parent field from struct acpi_device
ACPI: scan: Eliminate __acpi_device_add()
ACPI: scan: Rearrange initialization of ACPI device objects
ACPI: scan: Rename acpi_bus_get_parent() and rearrange it
ACPI: Rename acpi_bus_get/put_acpi_device()
SPI code checks for non-zero sgt->orig_nents to determine if the buffer
has been DMA-mapped. Ensure that sg_table is really zeroed after free to
avoid potential NULL pointer dereference if the given SPI xfer object is
reused again without being DMA-mapped.
Fixes: 0c17ba73c0 ("spi: Fix cache corruption due to DMA/PIO overlap")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220930113408.19720-1-m.szyprowski@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A couple of drivers call spi_split_transfers_maxsize() from their
->prepare_message() callbacks to split transfers which are too big for
them to handle. Add support in the core to do this based on
->max_transfer_size() to avoid code duplication.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-4-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core DMA mapping support performs cache management once for the
entire message and not between transfers, and this leads to cache
corruption if a message has two or more RX transfers with both
transfers targeting the same cache line, and the controller driver
decides to handle one using DMA and the other using PIO (for example,
because one is much larger than the other).
Fix it by syncing before/after the actual transfers. This also means
that we can skip the sync during the map/unmap of the message.
Fixes: 99adef310f ("spi: Provide core support for DMA mapping transfers")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-3-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Save the current RX and TX DMA devices to avoid having to duplicate the
logic to pick them, since we'll need access to them in some more
functions to fix a bug in the cache handling.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20220927112117.77599-2-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Several fixes that came in since the merge window, the major one being a
fix for the spi-mux driver which was broken by the performance
optimisations due to it peering inside the core's data structures more
than it should.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmMZ22MACgkQJNaLcl1U
h9BV9Af/fvJZTo35a2NBZ6kUw/V+73LSxfEfzfzjqfXhYTTiYshDTvRi7MK+FdrU
E84vuidJkmP1+NVRbyoiBbDhx9Ejq11tHL8rpCm/0PTrSd3jc2WMs9ODGG0XIXst
j3Q7WnaWOfvvETSDVw8jNs8B9zdMMXsluaTJUIn1hjQWSVYTt67hsqtwRjrRlwmI
xLjVcYygnsiggNetAKCqmamPG9W94v6aUlhQ7c7aiAqYwQgy94sCBye+T4pV64rK
mF28RkdDx6U9TA08uSepmwgUC9PEWyCIsVSoJs0DuKXZH9WQ/ixsFDubC8WodIKT
/IgtX+Xpf6bES6n8fi3tidd7HkXrqw==
=ZJei
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"Several fixes that came in since the merge window, the major one being
a fix for the spi-mux driver which was broken by the performance
optimisations due to it peering inside the core's data structures more
than it should"
* tag 'spi-fix-v6.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi: Fix queue hang if previous transfer failed
spi: mux: Fix mux interaction with fast path optimisations
spi: cadence-quadspi: Disable irqs during indirect reads
spi: bitbang: Fix lsb-first Rx
Some components require a few clock cycles with chipselect off before
or/and after the data transfer done with CS on.
Typically IDT 801034 QUAD PCM CODEC datasheet states "Note *: CCLK
should have one cycle before CS goes low, and two cycles after
CS goes high".
The cycles "before" are implicitely provided by all previous activity
on the SPI bus. But the cycles "after" must be provided in order to
terminate the SPI transfer.
In order to use that kind of component, add a cs_off flag to
spi_transfer struct. When this flag is set, the transfer is performed
with chipselect off. This allows consummer to add a dummy transfer
at the end of the transfer list which is performed with chipselect
OFF, providing the required additional clock cycles.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/434165c46f06d802690208a11e7ea2500e8da4c7.1662558898.git.christophe.leroy@csgroup.eu
Signed-off-by: Mark Brown <broonie@kernel.org>
The queue worker always needs to be kicked one final time after a transfer
is done in order to transition to idle (ctlr->busy = false).
Commit 69fa95905d ("spi: Ensure the io_mutex is held until
spi_finalize_current_message()") moved this code into
__spi_pump_messages(), but it was executed only if the transfer was
successful. This condition check causes ctlr-busy to stay true in case of
a failed transfer.
This in turn causes that no new work is ever scheduled to the work queue.
Fixes: 69fa95905d ("spi: Ensure the io_mutex is held until spi_finalize_current_message()")
Reported-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220901123630.1098433-1-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-mux driver is rather too clever and attempts to resubmit any
message that is submitted to it to the parent controller with some
adjusted callbacks. This does not play at all nicely with the fast
path which now sets flags on the message indicating that it's being
handled through the fast path, we see async messages flagged as being on
the fast path. Ideally the spi-mux code would duplicate the message but
that's rather invasive and a bit fragile in that it relies on the mux
knowing which fields in the message to copy. Instead teach the core
that there are controllers which can't cope with the fast path and have
the mux flag itself as being such a controller, ensuring that messages
going via the mux don't get partially handled via the fast path.
This will reduce the performance of any spi-mux connected device since
we'll now always use the thread for both the actual controller and the
mux controller instead of just the actual controller but given that we
were always hitting the slow path anyway it's hopefully not too much of
an additional cost and it allows us to keep the fast path.
Fixes: ae7d2346dc ("spi: Don't use the message queue if possible in spi_sync")
Reported-by: Casper Andersson <casper.casan@gmail.com>
Tested-by: Casper Andersson <casper.casan@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20220901120732.49245-1-broonie@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The parent field in struct acpi_device is, in fact, redundant,
because the dev.parent field in it effectively points to the same
object and it is used by the driver core.
Accordingly, the parent field can be dropped from struct acpi_device
and for this purpose define acpi_dev_parent() to retrieve a parent
struct acpi_device pointer from the dev.parent field in struct
acpi_device. Next, update all of the users of the parent field
in struct acpi_device to use acpi_dev_parent() instead of it and
drop it.
While at it, drop the ACPI_IS_ROOT_DEVICE() macro that is only used
in one place in a confusing way.
No intentional functional impact.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Reviewed-by: Punit Agrawal <punit.agrawal@bytedance.com>
A few fixes that came in since my pull request, the Meson fix is a
little large since it's fixing all possible cases of the problem that
was observed with the driver and clock API trying to share configuration
by integrating the device clocking fully with the clock API rather than
spot fixing the one instance that was observed.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmL7fVUACgkQJNaLcl1U
h9DNIAf/ThNZXWK1+ujLkCe3VW2CfOWSBQMtL1jW7vrRI2qNMoEj478wUMUZJ83R
Sl5X7w3PW7OmiJTvTzqngS+OkUUR/8Hcp8Cvcz1DJYmBV0iYOwPjinNfbB/Z77B7
4HaBOdBdMSCq6nFX7obKc4tyNGb6ZBD3YJ+PW+CRhUozfvGPXAUDoh5Eq4q1efh3
UJW5lP88Lp4zwd9rh8y05ugLFzXdxWV1LwICj2cj3+KceRwObwNfSs8Qp60iOrC+
QuSIiaZJA77BbG6y/i6Y/lZo/06ZcYAU0QzdUdaffNk+V7aadfvz2IlTHuoe186A
bV3xv1ucL2FJlrx4DAZtWp4b5EcPmA==
=xXEL
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few fixes that came in since my pull request, the Meson fix is a
little large since it's fixing all possible cases of the problem that
was observed with the driver and clock API trying to share
configuration by integrating the device clocking fully with the clock
API rather than spot fixing the one instance that was observed"
* tag 'spi-fix-v6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: dt-bindings: Drop Pratyush Yadav
spi: meson-spicc: add local pow2 clock ops to preserve rate between messages
MAINTAINERS: rectify entry for ARM/HPE GXP ARCHITECTURE
spi: spi.c: Add missing __percpu annotations in users of spi_statistics
Here is the set of driver core and kernfs changes for 6.0-rc1.
"biggest" thing in here is some scalability improvements for kernfs for
large systems. Other than that, included in here are:
- arch topology and cache info changes that have been reviewed
and discussed a lot.
- potential error path cleanup fixes
- deferred driver probe cleanups
- firmware loader cleanups and tweaks
- documentation updates
- other small things
All of these have been in the linux-next tree for a while with no
reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYuqCnw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym/JgCcCnaycJY00ZPRQm3LQCyzfJ0HgqoAn2qxGV+K
NKycLeXZSnuvIA87dycE
=/4Jk
-----END PGP SIGNATURE-----
Merge tag 'driver-core-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core / kernfs updates from Greg KH:
"Here is the set of driver core and kernfs changes for 6.0-rc1.
The "biggest" thing in here is some scalability improvements for
kernfs for large systems. Other than that, included in here are:
- arch topology and cache info changes that have been reviewed and
discussed a lot.
- potential error path cleanup fixes
- deferred driver probe cleanups
- firmware loader cleanups and tweaks
- documentation updates
- other small things
All of these have been in the linux-next tree for a while with no
reported problems"
* tag 'driver-core-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (63 commits)
docs: embargoed-hardware-issues: fix invalid AMD contact email
firmware_loader: Replace kmap() with kmap_local_page()
sysfs docs: ABI: Fix typo in comment
kobject: fix Kconfig.debug "its" grammar
kernfs: Fix typo 'the the' in comment
docs: driver-api: firmware: add driver firmware guidelines. (v3)
arch_topology: Fix cache attributes detection in the CPU hotplug path
ACPI: PPTT: Leave the table mapped for the runtime usage
cacheinfo: Use atomic allocation for percpu cache attributes
drivers/base: fix userspace break from using bin_attributes for cpumap and cpulist
MAINTAINERS: Change mentions of mpm to olivia
docs: ABI: sysfs-devices-soc: Update Lee Jones' email address
docs: ABI: sysfs-class-pwm: Update Lee Jones' email address
Documentation/process: Add embargoed HW contact for LLVM
Revert "kernfs: Change kernfs_notify_list to llist."
ACPI: Remove the unused find_acpi_cpu_cache_topology()
arch_topology: Warn that topology for nested clusters is not supported
arch_topology: Add support for parsing sockets in /cpu-map
arch_topology: Set cluster identifier in each core/thread from /cpu-map
arch_topology: Limit span of cpu_clustergroup_mask()
...
This reverts commit 59ebbe40fb ("spi: simplify
devm_spi_register_controller").
If devm_add_action() fails in devm_add_action_or_reset(),
devm_spi_unregister() will be called, it decreases the
refcount of 'ctlr->dev' to 0, then it will cause uaf in
the drivers that calling spi_put_controller() in error path.
Fixes: 59ebbe40fb ("spi: simplify devm_spi_register_controller")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/20220712135504.1055688-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The acpi_spi_add_resource() is never called with ctrl == NULL and
index == -1. The only caller already performs the check. Hence
remove the duplication from the acpi_spi_add_resource().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220709000709.35622-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since acpi_spi_device_alloc() has been designed to return an error
pointer we may now properly propagate error codes to the caller of
it. It helps debugging a lot.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220709000709.35622-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Capitalize first word in comment where appropriate and add
parentheses to function names.
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220629142519.3985486-3-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
There are only a few drivers that do not call
spi_finalize_current_message() in the context of transfer_one_message(),
and even for those cases the completion ctlr->cur_msg_completion is not
needed always. The calls to complete() and wait_for_completion() each
take a spin-lock, which is costly. This patch makes it possible to avoid
those calls in the big majority of cases, by introducing two flags that
with the help of ordering via barriers can avoid using the completion
safely. In case of a race with the context calling
spi_finalize_current_message(), the scheme errs on the safe side and takes
the completion.
The impact of this patch is worth the effort: On a i.MX8MM SoC, the time
the SPI bus is idle between two consecutive calls to spi_sync(), is
reduced from 19.6us to 16.8us... roughly 15%.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-12-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch introduces a completion that is completed in
spi_finalize_current_message() and waited for in
__spi_pump_transfer_message(). This way all manipulation of ctlr->cur_msg
is done with the io_mutex held and strictly ordered:
__spi_pump_transfer_message() will not return until
spi_finalize_current_message() is done using ctlr->cur_msg, and its
calling context is only touching ctlr->cur_msg after returning.
Due to this, we can safely drop the spin-locks around ctlr->cur_msg.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-11-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the whole idling transition is locked by the io_mutex now, there is
no need to check this flag anymore.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-7-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that the idling flag is wholly behind the io_mutex, this broken piece
of code can be safely removed.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-6-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
The interaction with the controller message queue and its corresponding
auxiliary flags and variables requires the use of the queue_lock which is
costly. Since spi_sync will transfer the complete message anyway, and not
return until it is finished, there is no need to put the message into the
queue if the queue is empty. This can save a lot of overhead.
As an example of how significant this is, when using the MCP2518FD SPI CAN
controller on a i.MX8MM SoC, the time during which the interrupt line
stays active (during 3 relatively short spi_sync messages), is reduced
from 98us to 72us by this patch.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-3-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
This enables the possibility to transfer a message that is not at the
current tip of the async message queue.
This is in preparation of the next patch(es) which enable spi_sync messages
to skip the queue altogether.
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220621061234.3626638-2-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
Return -ENOMEM if the allocation fails. Don't return success.
Fixes: 6598b91b5a ("spi: spi.c: Convert statistics to per-cpu u64_stats_t")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/Yqh6bdNYO2XNhPBa@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
We have already a helper to get the first child device, use it and
drop custom approach.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220610120219.18988-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 32 bit systems, the following kernel BUG is hit:
BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
caller is debug_smp_processor_id+0x18/0x24
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.19.0-rc1-00001-g6ae0aec8a366 #181
Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
Backtrace:
dump_backtrace from show_stack+0x20/0x24
r7:81024ffd r6:00000000 r5:81024ffd r4:60000013
show_stack from dump_stack_lvl+0x60/0x78
dump_stack_lvl from dump_stack+0x14/0x1c
r7:81024ffd r6:80f652de r5:80bec180 r4:819a2500
dump_stack from check_preemption_disabled+0xc8/0xf0
check_preemption_disabled from debug_smp_processor_id+0x18/0x24
r8:8119b7e0 r7:81205534 r6:819f5c00 r5:819f4c00 r4:c083d724
debug_smp_processor_id from __spi_sync+0x78/0x220
__spi_sync from spi_sync+0x34/0x4c
r10:bb7bf4e0 r9:c083d724 r8:00000007 r7:81a068c0 r6:822a83c0 r5:c083d724
r4:819f4c00
spi_sync from spi_mem_exec_op+0x338/0x370
r5:000000b4 r4:c083d910
spi_mem_exec_op from spi_nor_read_id+0x98/0xdc
r10:bb7bf4e0 r9:00000000 r8:00000000 r7:00000000 r6:00000000 r5:82358040
r4:819f7c40
spi_nor_read_id from spi_nor_detect+0x38/0x114
r7:82358040 r6:00000000 r5:819f7c40 r4:819f7c40
spi_nor_detect from spi_nor_scan+0x11c/0xbec
r10:bb7bf4e0 r9:00000000 r8:00000000 r7:c083da4c r6:00000000 r5:00010101
r4:819f7c40
spi_nor_scan from spi_nor_probe+0x10c/0x2d0
r10:bb7bf4e0 r9:bb7bf4d0 r8:00000000 r7:819f4c00 r6:00000000 r5:00000000
r4:819f7c40
per-cpu access needs to be guarded against preemption.
Fixes: 6598b91b5a ("spi: spi.c: Convert statistics to per-cpu u64_stats_t")
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David Jander <david@protonic.nl>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220609121334.2984808-1-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
This change gives a dramatic performance improvement in the hot path,
since many costly spin_lock_irqsave() calls can be avoided.
On an i.MX8MM system with a MCP2518FD CAN controller connected via SPI,
the time the driver takes to handle interrupts, or in other words the time
the IRQ line of the CAN controller stays low is mainly dominated by the
time it takes to do 3 relatively short sync SPI transfers. The effect of
this patch is a reduction of this time from 136us down to only 98us.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David Jander <david@protonic.nl>
Link: https://lore.kernel.org/r/20220524091808.2269898-1-david@protonic.nl
Signed-off-by: Mark Brown <broonie@kernel.org>
Here is the set of driver core changes for 5.19-rc1.
Note, I'm not really happy with this pull request as-is, see below for
details, but overall this is all good for everything but a small set of
systems, which we have a fix for already.
Lots of tiny driver core changes and cleanups happened this cycle,
but the two major things were:
- firmware_loader reorganization and additions including the
ability to have XZ compressed firmware images and the ability
for userspace to initiate the firmware load when it needs to,
instead of being always initiated by the kernel. FPGA devices
specifically want this ability to have their firmware changed
over the lifetime of the system boot, and this allows them to
work without having to come up with yet-another-custom-uapi
interface for loading firmware for them.
- physical location support added to sysfs so that devices that
know this information, can tell userspace where they are
located in a common way. Some ACPI devices already support
this today, and more bus types should support this in the
future.
Smaller changes included:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten any
linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request if you want to take them directly, _OR_ I can just revert
the probe timeout changes and they can wait for the next -rc1 merge
cycle. Given that the fixes are tested, and pretty simple, I'm leaning
toward that choice. Sorry this all came at the end of the merge window,
I should have resolved this all 2 weeks ago, that's my fault as it was
in the middle of some travel for me.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time outs.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnv/A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk/fACgvmenbo5HipqyHnOmTQlT50xQ9EYAn2eTq6ai
GkjLXBGNWOPBa5cU52qf
=yEi/
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of driver core changes for 5.19-rc1.
Lots of tiny driver core changes and cleanups happened this cycle, but
the two major things are:
- firmware_loader reorganization and additions including the ability
to have XZ compressed firmware images and the ability for userspace
to initiate the firmware load when it needs to, instead of being
always initiated by the kernel. FPGA devices specifically want this
ability to have their firmware changed over the lifetime of the
system boot, and this allows them to work without having to come up
with yet-another-custom-uapi interface for loading firmware for
them.
- physical location support added to sysfs so that devices that know
this information, can tell userspace where they are located in a
common way. Some ACPI devices already support this today, and more
bus types should support this in the future.
Smaller changes include:
- driver_override api cleanups and fixes
- error path cleanups and fixes
- get_abi script fixes
- deferred probe timeout changes.
It's that last change that I'm the most worried about. It has been
reported to cause boot problems for a number of systems, and I have a
tested patch series that resolves this issue. But I didn't get it
merged into my tree before 5.18-final came out, so it has not gotten
any linux-next testing.
I'll send the fixup patches (there are 2) as a follow-on series to this
pull request.
All have been tested in linux-next for weeks, with no reported issues
other than the above-mentioned boot time-outs"
* tag 'driver-core-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (55 commits)
driver core: fix deadlock in __device_attach
kernfs: Separate kernfs_pr_cont_buf and rename_lock.
topology: Remove unused cpu_cluster_mask()
driver core: Extend deferred probe timeout on driver registration
MAINTAINERS: add Russ Weight as a firmware loader maintainer
driver: base: fix UAF when driver_attach failed
test_firmware: fix end of loop test in upload_read_show()
driver core: location: Add "back" as a possible output for panel
driver core: location: Free struct acpi_pld_info *pld
driver core: Add "*" wildcard support to driver_async_probe cmdline param
driver core: location: Check for allocations failure
arch_topology: Trace the update thermal pressure
kernfs: Rename kernfs_put_open_node to kernfs_unlink_open_file.
export: fix string handling of namespace in EXPORT_SYMBOL_NS
rpmsg: use local 'dev' variable
rpmsg: Fix calling device_lock() on non-initialized device
firmware_loader: describe 'module' parameter of firmware_upload_register()
firmware_loader: Move definitions from sysfs_upload.h to sysfs.h
firmware_loader: Fix configs for sysfs split
selftests: firmware: Add firmware upload selftests
...
A couple of fixes that came in during the merge window, a driver
fix for spurious timeouts in the fsi driver and an improvement to
make the core display error messages for transfer_one_message()
to help people debug things.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmKXHOwACgkQJNaLcl1U
h9Cxtgf+KCYOZovyBpvHaGuwUrf5fJ3SEbS5BaEhGjyQfTSeSbZuct0+gREJbBu4
AkEOt1/VXWm3EILFbLJV1xsvIj7xhQMwGRhoKEAZ0wjtV/YK2IMC6ISvrDZL2Prr
+A/p5PJu0dHLFlOUfKbkEMa2Ez/Gm/BUR6sfCzswqG6qebRcVF6svctZ/gm+Dqvy
cBvJxqIbSdYwzAqkbrTCZiQgbtJrntagaP4WtpReTMpqrLuXD/VBFK8anzhVsREz
wCTFBi0tSSe6yXOgtGc1Gzvj2wFZ2LRGPvV7nLSfQ2YaruoSM1rwo/xPxtWxsn85
MK8dp1L5d0j7LKzG2q/gPhih0oA1Bg==
=gf5o
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of fixes that came in during the merge window: a driver fix
for spurious timeouts in the fsi driver and an improvement to make the
core display error messages for transfer_one_message() to help people
debug things"
* tag 'spi-fix-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: core: Display return code when failing to transfer message
spi: fsi: Fix spurious timeout
