1. ata_pio_complete():
It seems unnecessary to wait for the clearing of the DRQ bit.
(Waiting for BSY=0 should be enough.
ata_ok() also checks the correctness of the status bits later.)
2. ata_pio_block():
- added error checking, before transfering data.
- minor comments fix
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- set qc->err_mask directly when we found the error
- remove the code to determine err_mask from device status
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- move "qc->err_mask |= AC_ERR_ATA_BUS" to where the error is found
- add "assert(qc->err_mask)" to ata_pio_error() to make sure qc->err_mask was available when we enter the error state
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- remove err_mask from the parameter list of the complete functions
- move err_mask to ata_queued_cmd
- initialize qc->err_mask when needed
- for each function call to ata_qc_complete(), replace the err_mask parameter with qc->err_mask.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
===============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- add qc to ata_pio_poll()
- reorder the initialization of qc in ata_pio_complete()
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
===================
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Hi,
the patch below marks several libata (and libata-driver) structures
const so that they end up in the .rodata segment and don't false-share
cachelines with things that get dirtied often.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The following code segment is not functional because the transfer cycle time speficied by
the EIDE device is later overwritten by ata_timing_quantize():
/*
* If the drive is an EIDE drive, it can tell us it needs extended
* PIO/MW_DMA cycle timing.
*/
if (adev->id[ATA_ID_FIELD_VALID] & 2) { /* EIDE drive */
memset(&p, 0, sizeof(p));
(snip)
ata_timing_merge(&p, t, t, ATA_TIMING_CYCLE | ATA_TIMING_CYC8B);
<== uninitialized "t" is used here
}
/*
* Convert the timing to bus clock counts.
*/
ata_timing_quantize(s, t, T, UT); <== t is overwritten by quantized s
The patch has been submitted for ide-timing.h before:
http://marc.theaimsgroup.com/?l=linux-ide&m=110820013425454&w=2
Resubmitted for libata.
Changes:
- Minor fix to honor the following transfer cycle time speficied by the device
- id[65]: Minimum Multiword DMA transfer cycle time per word
- id[67]: Minimum PIO transfer cycle time without flow control
- id[68]: Minimum PIO transfer cycle time with IORDY
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
=======
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Move ATAPI check-condition handling out of the timeout handler
- Use multi-qc-issue feature to issue REQUEST SENSE ATAPI PACKET
command upon receiving an ATAPI check-condition.
This cleans things up a lot, and eliminates a nasty recursion bug.
- in ata_dev_identify(), don't assume that all devices are either
ATA or ATAPI. In the future, this code will see port multipliers
and other devices.
- make a debugging printk less verbose
- add new helper ata_qc_reinit()
- add new helper BPRINTK() and port flag ATA_FLAG_DEBUGMSG, for
fine-grained debugging use.
The ATAPI pad-to-next-32bit-boundary code modifies the scatterlist's
length variable, sometimes to zero. x86-64 platform would oops if a
zero-length scatterlist entry was asked to be mapped. Work around this
by ensuring that we never DMA-map a zero length buffer or SG entry.
This will let me chop the code size of several drivers right down. In
many cases the actual private data is very useful and constant for a
given host controller so being able to just pass it at probe time would
be very useful indeed (eg with the via driver would could pass the udma
clocking and reduce the code size, or with the AMD one the UDMA
multiplier and the offset)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- if condition fix for ata_dev_identify()
- ata_pio_poll() minor cleanup.
Changes:
- Use (dev->class == ATA_DEV_ATA) for ata_dev_identify()
since "qc->tf.command" has been overwritten by the device status
- Use HSM_ST_TMOUT directly in ata_pio_poll()
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- add is_multi_taskfile() to ata.h
- initialize ata_device->multi_count with device identify data
- use ata_pio_sectors() to support r/w multiple commands
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
========
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- change the return value of ata_pio_complete() 0 <-> 1
- add return value for ata_pio_first_block()
- rename variable "qc_completed" to "has_next" in ata_pio_task()
- use has_next to eliminate unnecessary queuing in ata_pio_first_block()
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
==========
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- remove ap->dataout_task from struct ata_port
- let ata_pio_task() handle the HSM_ST_FIRST state.
- rename ata_dataout_task() to ata_pio_first_block()
- replace the ata_dataout_task workqueue with ata_pio_task workqueue
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
========
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- ata_pio_block(): add ata_altstatus(ap) to prevent reading device status before it is valid
- remove the unnecessary HSM_ST_IDLE state from ata_pio_task()
- raise BUG() when unknown state is found in ata_pio_task()
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use ata_pad_{alloc,free} in two drivers, to factor out common code.
Add ata_pad_{alloc,free} to two other drivers, which needed the padding
but had not been updated.
A lot of power packed into a little patch.
This change eliminates the sharing between our controller-wide spinlock
and the SCSI core's Scsi_Host lock. As the locking in libata was
already highly compartmentalized, always referencing our own lock, and
never scsi_host::host_lock.
As a side effect, this change eliminates a deadlock from calling
scsi_finish_command() while inside our spinlock.
Integrate ata_exec() and ata_tf_to_host() into their only caller,
ata_bus_edd().
Rename ata_tf_to_host_nolock() to ata_tf_to_host().
This makes locking a bit easier to review, and may help pave the way for
future changes.
ata_pci_init_one() receives an array of struct ata_port_info. Recent
updates to the code had always obtained port information from
array element 0, rather than array element N.
Change to avoid hardcoding port_info[0], thereby restoring proper
hardware information to secondary legacy ports.
The second argument to ata_qc_complete() was being used for two
purposes: communicate the ATA Status register to the completion
function, and indicate an error. On legacy PCI IDE hardware, the latter
is often implicit in the former. On more modern hardware, the driver
often completely emulated a Status register value, passing ATA_ERR as an
indication that something went wrong.
Now that previous code changes have eliminated the need to use drv_stat
arg to communicate the ATA Status register value, we can convert it to a
mask of possible error classes.
This will lead to more flexible error handling in the future.
This patch uses sg_set_buf/sg_init_one in some places where it was
duplicated.
Signed-off-by: David Hardeman <david@2gen.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Greg KH <greg@kroah.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
libata-core cleanups:
- use kzalloc() instead of kmalloc() + memset();
- use one exit path in ata_device_add();
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
We want ->tf_read() to get a complete snapshot of all taskfile
registers, without requiring the callers to manually call
ata_chk_status() and ata_chk_err() themselves.
This also fixes a minor bug in sata_vsc where the lower bits of the
feature register were incorrectly placed in the HOB (high order bits)
portion of struct ata_taskfile.
Correct some function names in kernel-doc.
Add some kernel-doc descriptions.
Fix some typos.
Remove a few blank lines.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is needed for full AMD and VIA drivers and possibly more. Functions
to turn actual clocking and cycle timings into register values. Also to
merge shared timings to compute an optimal timing set.
Built from the drivers/ide version by Vojtech Pavlik
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
problem:
id[53-58] might be changed after initializing device CHS settings.
changes:
- call ata_dev_reread_id() to reread the identify device info,
after initializing device CHS settings.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- merge ata_prot_to_cmd() and ata_dev_set_protocol() as
ata_rwcmd_protocol()
- pave road for read/write multiple support
- remove usage of pre-cached command and protocol values and call
ata_rwcmd_protocol() instead
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
==============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
move the initialization of taskfile LBA flags
"ATA_TFLAG_LBA" and "ATA_TFLAG_LBA48 flags"
to the SCSI translation functions
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
=============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- move some code out of the kmap_atomic() / kunmap_atomic() zone
- remove the redundant "do_write = (qc->tf.flags & ATA_TFLAG_WRITE);"
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
This redoes the n_ports logic I proposed before as a bitmask.
ata_pci_init_native_mode is now used with a mask allowing for mixed mode
stuff later on. ata_pci_init_legacy_port is called with port number and
does one port now not two. Instead it is called twice by the ata init
logic which cleans both of them up.
There are stil limits in the original code left over
- IRQ/port mapping for legacy mode should be arch specific values
- You can have one legacy mode IDE adapter per PCI root bridge on some systems
- Doesn't handle mixed mode devices yet (but is now a lot closer to it)
Replace SCSI's legacy "bang at the door" method of probing with one
directly controlled by the underlying ATA transport layer.
We now only call scsi_scan_target() for devices we find, rather than
probing every possible channel/id within a certain range.
ata_qc_issue_prot():
- cleanup and let the PIO data out case always go through the
ata_dataout_task() codepath.
(Previously for PIO data out case, 2 code pathes were used
- irq case goes through ata_data_out_task() codepath.
- polling case jumps over the HSM_ST_FIRST state and goes to
HSM_ST and ata_pio_task() directly.)
ata_dataout_task():
- rearrange the queue_work() code to handle the PIO data out +
polling case.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- Use if (qc->tf.protocol == ATA_PROT_PIO) instead of
if(is_atapi_taskfile()) in ata_dataout_task()
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
libata.h:
libata-core:
Add ATA_FLAG_PIO_POLLING flag for LLDs that expect interrupt for
command completion only.
sata_nv.c:
sata_vsc.c:
irq handler is wrapper around ata_host_intr(), can handle PIO interrupts.
sata_promise.c:
sata_sx4.c:
sata_qstor.c:
sata_mv.c:
Private irq handler.
Polling mode ATA_FLAG_PIO_POLLING used for compatibility.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- add PIO_ST_FIRST for the state before sending ATAPI CDB or sending
"ATA PIO data out" first data block.
- add ATA_TFLAG_POLLING and ATA_DFLAG_CDB_INTR flags
- remove the ATA_FLAG_NOINTR flag since the interrupt handler is now
aware of the states
- modify ata_pio_sector() and atapi_pio_bytes() to work in the interrupt
context
- modify the ata_host_intr() to handle PIO interrupts
- modify ata_qc_issue_prot() to initialize states
- atapi_packet_task() changed to handle "ATA PIO data out" first data block
- support the pre-ATA4 ATAPI device which raise interrupt when ready to
receive CDB
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Changes:
s/PIO_ST_/HSM_ST_/ and s/pio_task_state/hsm_task_state/.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Make sure we that completion is the final action we take; prior to this
change, another CPU may have changed ap->pio_task_state before we tested
it a final time.
Spotted by, and original patch by Albert Lee @ IBM.
Also includes a minor optimization: eliminate a ton of unnecessary
queue_work() calls, simply by jumping to the beginning of the FSM
function ata_pio_task().
ATAPI is getting close to being ready. To increase exposure, we enable
the code in the upstream kernel, but default it to off (present
behavior). Users must pass atapi_enabled=1 as a module option (if
module) or on the kernel command line (if built in) to turn on
discovery of their ATAPI devices.
- changes license of all code from OSL+GPL to plain ole GPL
- except for NVIDIA, who hasn't yet responded about sata_nv
- copyright holders were already contacted privately
- adds info in each driver about where hardware/protocol docs may be
obtained
- where I have made major contributions, updated copyright dates
You spelt heuristic wrongly. Also reformatted to 80 columns,
ignore the diff and fix the typo if you prefer that.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
[PATCH libata-dev-2.6:upstream] implement ata_poll_qc_complete and use it in polling functions
Previously, libata polling functions turned irq back on and completed
qc commands without holding host lock. This creates a race condition
between the polling task and interrupts from other ports on the same
host set or spurious interrupt from itself.
This patch implements ata_poll_qc_complete which enables irq and
completes qc atomically and convert all polling functions.
Note: atapi_packet_task() didn't use to turn irq back on or clear
ATA_FLAG_NOINTR on error exits. This patch makes it use
ata_poll_qc_complete which does both.
Note: With this change, ALL invocations of ata_qc_complete() are now
done under host_set lock.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Interrupts from devices sharing the same IRQ could cause
ata_host_intr to finish commands being processed by atapi_packet_task
if the commands are using ATA_PROT_ATAPI_NODATA or ATA_PROT_ATAPI_DMA
protocol. This is because libata interrupt handler is unaware that
interrupts are not expected during that period. This patch adds
ATA_FLAG_NOINTR flag to tell the interrupt handler that we're not
expecting interrupts.
Note that once proper HSM is implemented for interrupt-driven PIO,
this should be merged into it and this flag will be removed.
ahci.c is a different kind of beast, so it's left alone.
* The following drivers use ata_qc_issue_prot and ata_interrupt, so
changes in libata core will do.
ata_piix sata_sil sata_svw sata_via sata_sis sata_uli
* The following drivers use ata_qc_issue_prot and custom intr handler.
They need this change to work correctly.
sata_nv sata_vsc
* The following drivers use custom issue function and intr handler.
Currently all custom issue functions don't support ATAPI, so this
change is irrelevant, updated for consistency and to avoid later
mistakes.
sata_promise sata_qstor sata_sx4
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Description:
After calling the completion callback, the libata error handler might be
running and getting atapi sense data. Clearing the ATA_QCFLAG_ACTIVE flag
at this point might interfere with the libata error handler.
Changes:
- Clear the ATA_QCFLAG_ACTIVE flag before calling the completion callback
(and also before the error handler)
- Add some comment
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
PATCH 2/2: handle the case when device returns/needs extra data
Description:
Sometimes the device returns/needs extra data than expected.
Changes:
Modify __atapi_pio_bytes() to handle the case where device returns/needs extra data.
- for read case, discard trailing data from the device
- for write case, padding zero data to the device
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
PATCH 1/2: ata_data_xfer() fix
Changes:
- Modify ata_mmio_data_xfer() and ata_pio_data_xfer() to handle odd-lengthed buffer.
- Add some function comments
This patch does not reuse ap->pad as alignment buffer since
using local variable seems good enough.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch lengthens the delay between DET setting and clearing for
COMMRESET from 400us to 1ms. I couldn't find any requiremen regarding
the duration of COMMRESET in SATA I/II specs but AHCI-1.1 10.4.2
states that it should be at least 1ms.
Signed-off-by: Tejun Heo <htejun@gmail.com>
scsi_add_host is the proper place to set the device, but people copy
the scsi_set_device usage from older drivers again and again.
note that this leaves some legacy drivers like qlogicisp/qlogicfc
without pci association in sysfs, but they're scheduled to go away soon
anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Problem:
Incorrect md5sum when using ATAPI PIO mode to verify a distro CD.
Root cause: sg traverse problem.
In __atapi_pio_bytes(), if qc->cursg++ is increased and "goto
next_page" is executed, then sg is not updated to the new qc->cursg
and the old sg is overwritten with the new data.
Changes:
- Replace "goto next_page" with "goto next_sg" to make sg updated.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Jens Axboe pointed out that the iounmap() call in libata was occurring
too early, and some drivers (ahci, probably others) were using ioremap'd
memory after it had been unmapped.
The patch should address that problem by way of improving the libata
driver API:
* move ->host_stop() call after all ->port_stop() calls have occurred.
* create default helper function ata_host_stop(), and move iounmap()
call there.
* add ->host_stop_prewalk() hook, use it in sata_qstor.c (hi Mark).
sata_qstor appears to require the host-stop-before-port-stop ordering
that existed prior to applying the attached patch.
When testing ATAPI PIO data transfer on the ppc64 platform, __atapi_pio_bytes() got zero when
sg_dma_len() is used. I checked the <asm-ppc64/scatterlish.h>, the struct scatterlist is defined as:
struct scatterlist {
struct page *page;
unsigned int offset;
unsigned int length;
/* For TCE support */
u32 dma_address;
u32 dma_length;
};
#define sg_dma_address(sg) ((sg)->dma_address)
#define sg_dma_len(sg) ((sg)->dma_length)
So, if the scatterlist is not DMA mapped, sg_dma_len() will return zero on ppc64.
The same problem should occur on the x86-64 platform.
On the i386 platform, sg_dma_len() returns sg->length, that's why the problem does not occur on an i386.
Changes:
- Use sg->length if the scatterlist is not DMA mapped (yet).
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Updated patch to fix erroneous flush of COMRESET set and missing flush
of COMRESET clear. Created a new routine scr_write_flush() to try to
prevent this in the future. Also, this patch is based on libata-2.6
instead of the previous libata-dev-2.6 based patch.
Signed-off-by: Brett Russ <russb@emc.com>
Index: libata-2.6/drivers/scsi/libata-core.c
===================================================================
Problem:
During the libata CD-ROM stress test, sometimes the "BUG: timeout
without command" error is seen.
Root cause:
Unexpected interrupt occurs after the ata_qc_complete() is called,
but before the SCSI error handler. The interrupt handler is invoked
before the SCSI error handler, and it clears the command by calling
ata_qc_complete() again. Later when the SCSI error handler is run,
the ata_queued_cmd is already gone, causing the "BUG: timeout without
command" error.
Changes:
- Use the ATA_QCFLAG_ACTIVE flag to prevent the interrupt handler
from completing the command twice, before the scsi_error_handler.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
This patch works around an issue with WD drives (and possibly others)
over SiL PATA->SATA Bridges on SATA controllers locking up with
transfers > 200 sectors.
Signed-off-by: Brad Campbell <brad@wasp.net.au>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
