For VMX, when a vcpu enters HLT emulation, pi_post_block will:
1) Add vcpu to per-cpu list of blocked vcpus.
2) Program the posted-interrupt descriptor "notification vector"
to POSTED_INTR_WAKEUP_VECTOR
With interrupt remapping, an interrupt will set the PIR bit for the
vector programmed for the device on the CPU, test-and-set the
ON bit on the posted interrupt descriptor, and if the ON bit is clear
generate an interrupt for the notification vector.
This way, the target CPU wakes upon a device interrupt and wakes up
the target vcpu.
Problem is that pi_post_block only programs the notification vector
if kvm_arch_has_assigned_device() is true. Its possible for the
following to happen:
1) vcpu V HLTs on pcpu P, kvm_arch_has_assigned_device is false,
notification vector is not programmed
2) device is assigned to VM
3) device interrupts vcpu V, sets ON bit
(notification vector not programmed, so pcpu P remains in idle)
4) vcpu 0 IPIs vcpu V (in guest), but since pi descriptor ON bit is set,
kvm_vcpu_kick is skipped
5) vcpu 0 busy spins on vcpu V's response for several seconds, until
RCU watchdog NMIs all vCPUs.
To fix this, use the start_assignment kvm_x86_ops callback to kick
vcpus out of the halt loop, so the notification vector is
properly reprogrammed to the wakeup vector.
Reported-by: Pei Zhang <pezhang@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Message-Id: <20210526172014.GA29007@fuller.cnet>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM_REQ_UNBLOCK will be used to exit a vcpu from
its inner vcpu halt emulation loop.
Rename KVM_REQ_PENDING_TIMER to KVM_REQ_UNBLOCK, switch
PowerPC to arch specific request bit.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Message-Id: <20210525134321.303768132@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is inspired by commit 262de4102c (kvm: exit halt polling on
need_resched() as well). Due to PPC implements an arch specific halt
polling logic, we have to the need_resched() check there as well. This
patch adds a helper function that can be shared between book3s and generic
halt-polling loops.
Reviewed-by: David Matlack <dmatlack@google.com>
Reviewed-by: Venkatesh Srinivas <venkateshs@chromium.org>
Cc: Ben Segall <bsegall@google.com>
Cc: Venkatesh Srinivas <venkateshs@chromium.org>
Cc: Jim Mattson <jmattson@google.com>
Cc: David Matlack <dmatlack@google.com>
Cc: Paul Mackerras <paulus@ozlabs.org>
Cc: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1621339235-11131-1-git-send-email-wanpengli@tencent.com>
[Make the function inline. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Fix regression with irqbypass not restarting the guest on failed connect
- Fix regression with debug register decoding resulting in overlapping access
- Commit exception state on exit to usrspace
- Fix the MMU notifier return values
- Add missing 'static' qualifiers in the new host stage-2 code
-----BEGIN PGP SIGNATURE-----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=57tg
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 5.13, take #1
- Fix regression with irqbypass not restarting the guest on failed connect
- Fix regression with debug register decoding resulting in overlapping access
- Commit exception state on exit to usrspace
- Fix the MMU notifier return values
- Add missing 'static' qualifiers in the new host stage-2 code
This reverts commit a979a6aa00.
The reverted commit may cause VM freeze on arm64 with GICv4,
where stopping a consumer is implemented by suspending the VM.
Should the connect fail, the VM will not be resumed, which
is a bit of a problem.
It also erroneously calls the producer destructor unconditionally,
which is unexpected.
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Suggested-by: Marc Zyngier <maz@kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Zhu Lingshan <lingshan.zhu@intel.com>
[maz: tags and cc-stable, commit message update]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Fixes: a979a6aa00 ("irqbypass: do not start cons/prod when failed connect")
Link: https://lore.kernel.org/r/3a2c66d6-6ca0-8478-d24b-61e8e3241b20@hisilicon.com
Link: https://lore.kernel.org/r/20210508071152.722425-1-lingshan.zhu@intel.com
Cc: stable@vger.kernel.org
When growing halt-polling, there is no check that the poll time exceeds
the per-VM limit. It's possible for vcpu->halt_poll_ns to grow past
kvm->max_halt_poll_ns and stay there until a halt which takes longer
than kvm->halt_poll_ns.
Signed-off-by: David Matlack <dmatlack@google.com>
Signed-off-by: Venkatesh Srinivas <venkateshs@chromium.org>
Message-Id: <20210506152442.4010298-1-venkateshs@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
single_task_running() is usually more general than need_resched()
but CFS_BANDWIDTH throttling will use resched_task() when there
is just one task to get the task to block. This was causing
long-need_resched warnings and was likely allowing VMs to
overrun their quota when halt polling.
Signed-off-by: Ben Segall <bsegall@google.com>
Signed-off-by: Venkatesh Srinivas <venkateshs@chromium.org>
Message-Id: <20210429162233.116849-1-venkateshs@chromium.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jim Mattson <jmattson@google.com>
Both lock holder vCPU and IPI receiver that has halted are condidate for
boost. However, the PLE handler was originally designed to deal with the
lock holder preemption problem. The Intel PLE occurs when the spinlock
waiter is in kernel mode. This assumption doesn't hold for IPI receiver,
they can be in either kernel or user mode. the vCPU candidate in user mode
will not be boosted even if they should respond to IPIs. Some benchmarks
like pbzip2, swaptions etc do the TLB shootdown in kernel mode and most
of the time they are running in user mode. It can lead to a large number
of continuous PLE events because the IPI sender causes PLE events
repeatedly until the receiver is scheduled while the receiver is not
candidate for a boost.
This patch boosts the vCPU candidiate in user mode which is delivery
interrupt. We can observe the speed of pbzip2 improves 10% in 96 vCPUs
VM in over-subscribe scenario (The host machine is 2 socket, 48 cores,
96 HTs Intel CLX box). There is no performance regression for other
benchmarks like Unixbench spawn (most of the time contend read/write
lock in kernel mode), ebizzy (most of the time contend read/write sem
and TLB shoodtdown in kernel mode).
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Message-Id: <1618542490-14756-1-git-send-email-wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a capability for userspace to mirror SEV encryption context from
one vm to another. On our side, this is intended to support a
Migration Helper vCPU, but it can also be used generically to support
other in-guest workloads scheduled by the host. The intention is for
the primary guest and the mirror to have nearly identical memslots.
The primary benefits of this are that:
1) The VMs do not share KVM contexts (think APIC/MSRs/etc), so they
can't accidentally clobber each other.
2) The VMs can have different memory-views, which is necessary for post-copy
migration (the migration vCPUs on the target need to read and write to
pages, when the primary guest would VMEXIT).
This does not change the threat model for AMD SEV. Any memory involved
is still owned by the primary guest and its initial state is still
attested to through the normal SEV_LAUNCH_* flows. If userspace wanted
to circumvent SEV, they could achieve the same effect by simply attaching
a vCPU to the primary VM.
This patch deliberately leaves userspace in charge of the memslots for the
mirror, as it already has the power to mess with them in the primary guest.
This patch does not support SEV-ES (much less SNP), as it does not
handle handing off attested VMSAs to the mirror.
For additional context, we need a Migration Helper because SEV PSP
migration is far too slow for our live migration on its own. Using
an in-guest migrator lets us speed this up significantly.
Signed-off-by: Nathan Tempelman <natet@google.com>
Message-Id: <20210408223214.2582277-1-natet@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Convert a comment above kvm_io_bus_unregister_dev() into an actual
lockdep assertion, and opportunistically add curly braces to a multi-line
for-loop.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210412222050.876100-4-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Abort the walk of coalesced MMIO zones if kvm_io_bus_unregister_dev()
fails to allocate memory for the new instance of the bus. If it can't
instantiate a new bus, unregister_dev() destroys all devices _except_ the
target device. But, it doesn't tell the caller that it obliterated the
bus and invoked the destructor for all devices that were on the bus. In
the coalesced MMIO case, this can result in a deleted list entry
dereference due to attempting to continue iterating on coalesced_zones
after future entries (in the walk) have been deleted.
Opportunistically add curly braces to the for-loop, which encompasses
many lines but sneaks by without braces due to the guts being a single
if statement.
Fixes: f65886606c ("KVM: fix memory leak in kvm_io_bus_unregister_dev()")
Cc: stable@vger.kernel.org
Reported-by: Hao Sun <sunhao.th@gmail.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210412222050.876100-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If allocating a new instance of an I/O bus fails when unregistering a
device, wait to destroy the device until after all readers are guaranteed
to see the new null bus. Destroying devices before the bus is nullified
could lead to use-after-free since readers expect the devices on their
reference of the bus to remain valid.
Fixes: f65886606c ("KVM: fix memory leak in kvm_io_bus_unregister_dev()")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210412222050.876100-2-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Defer acquiring mmu_lock in the MMU notifier paths until a "hit" has been
detected in the memslots, i.e. don't take the lock for notifications that
don't affect the guest.
For small VMs, spurious locking is a minor annoyance. And for "volatile"
setups where the majority of notifications _are_ relevant, this barely
qualifies as an optimization.
But, for large VMs (hundreds of threads) with static setups, e.g. no
page migration, no swapping, etc..., the vast majority of MMU notifier
callbacks will be unrelated to the guest, e.g. will often be in response
to the userspace VMM adjusting its own virtual address space. In such
large VMs, acquiring mmu_lock can be painful as it blocks vCPUs from
handling page faults. In some scenarios it can even be "fatal" in the
sense that it causes unacceptable brownouts, e.g. when rebuilding huge
pages after live migration, a significant percentage of vCPUs will be
attempting to handle page faults.
x86's TDP MMU implementation is especially susceptible to spurious
locking due it taking mmu_lock for read when handling page faults.
Because rwlock is fair, a single writer will stall future readers, while
the writer is itself stalled waiting for in-progress readers to complete.
This is exacerbated by the MMU notifiers often firing multiple times in
quick succession, e.g. moving a page will (always?) invoke three separate
notifiers: .invalidate_range_start(), invalidate_range_end(), and
.change_pte(). Unnecessarily taking mmu_lock each time means even a
single spurious sequence can be problematic.
Note, this optimizes only the unpaired callbacks. Optimizing the
.invalidate_range_{start,end}() pairs is more complex and will be done in
a future patch.
Suggested-by: Ben Gardon <bgardon@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-9-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Acquire and release mmu_lock in the __kvm_handle_hva_range() helper
instead of requiring the caller to do the same. This paves the way for
future patches to take mmu_lock if and only if an overlapping memslot is
found, without also having to introduce the on_lock() shenanigans used
to manipulate the notifier count and sequence.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-8-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Yank out the hva-based MMU notifier APIs now that all architectures that
use the notifiers have moved to the gfn-based APIs.
No functional change intended.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-7-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move the hva->gfn lookup for MMU notifiers into common code. Every arch
does a similar lookup, and some arch code is all but identical across
multiple architectures.
In addition to consolidating code, this will allow introducing
optimizations that will benefit all architectures without incurring
multiple walks of the memslots, e.g. by taking mmu_lock if and only if a
relevant range exists in the memslots.
The use of __always_inline to avoid indirect call retpolines, as done by
x86, may also benefit other architectures.
Consolidating the lookups also fixes a wart in x86, where the legacy MMU
and TDP MMU each do their own memslot walks.
Lastly, future enhancements to the memslot implementation, e.g. to add an
interval tree to track host address, will need to touch far less arch
specific code.
MIPS, PPC, and arm64 will be converted one at a time in future patches.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210402005658.3024832-3-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In KVM's .change_pte() notification callback, replace the notifier
sequence bump with a WARN_ON assertion that the notifier count is
elevated. An elevated count provides stricter protections than bumping
the sequence, and the sequence is guarnateed to be bumped before the
count hits zero.
When .change_pte() was added by commit 828502d300 ("ksm: add
mmu_notifier set_pte_at_notify()"), bumping the sequence was necessary
as .change_pte() would be invoked without any surrounding notifications.
However, since commit 6bdb913f0a ("mm: wrap calls to set_pte_at_notify
with invalidate_range_start and invalidate_range_end"), all calls to
.change_pte() are guaranteed to be surrounded by start() and end(), and
so are guaranteed to run with an elevated notifier count.
Note, wrapping .change_pte() with .invalidate_range_{start,end}() is a
bug of sorts, as invalidating the secondary MMU's (KVM's) PTE defeats
the purpose of .change_pte(). Every arch's kvm_set_spte_hva() assumes
.change_pte() is called when the relevant SPTE is present in KVM's MMU,
as the original goal was to accelerate Kernel Samepage Merging (KSM) by
updating KVM's SPTEs without requiring a VM-Exit (due to invalidating
the SPTE). I.e. it means that .change_pte() is effectively dead code
on _all_ architectures.
x86 and MIPS are clearcut nops if the old SPTE is not-present, and that
is guaranteed due to the prior invalidation. PPC simply unmaps the SPTE,
which again should be a nop due to the invalidation. arm64 is a bit
murky, but it's also likely a nop because kvm_pgtable_stage2_map() is
called without a cache pointer, which means it will map an entry if and
only if an existing PTE was found.
For now, take advantage of the bug to simplify future consolidation of
KVMs's MMU notifier code. Doing so will not greatly complicate fixing
.change_pte(), assuming it's even worth fixing. .change_pte() has been
broken for 8+ years and no one has complained. Even if there are
KSM+KVM users that care deeply about its performance, the benefits of
avoiding VM-Exits via .change_pte() need to be reevaluated to justify
the added complexity and testing burden. Ripping out .change_pte()
entirely would be a lot easier.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use GFP_KERNEL_ACCOUNT when allocating vCPUs to make it more obvious that
that the allocations are accounted, to make it easier to audit KVM's
allocations in the future, and to be consistent with other cache usage in
KVM.
When using SLAB/SLUB, this is a nop as the cache itself is created with
SLAB_ACCOUNT.
When using SLOB, there are caveats within caveats. SLOB doesn't honor
SLAB_ACCOUNT, so passing GFP_KERNEL_ACCOUNT will result in vCPU
allocations now being accounted. But, even that depends on internal
SLOB details as SLOB will only go to the page allocator when its cache is
depleted. That just happens to be extremely likely for vCPUs because the
size of kvm_vcpu is larger than the a page for almost all combinations of
architecture and page size. Whether or not the SLOB behavior is by
design is unknown; it's just as likely that no SLOB users care about
accounding and so no one has bothered to implemented support in SLOB.
Regardless, accounting vCPU allocations will not break SLOB+KVM+cgroup
users, if any exist.
Reviewed-by: Wanpeng Li <kernellwp@gmail.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210406190740.4055679-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Move arm64's MMU notifier trace events into common code in preparation
for doing the hva->gfn lookup in common code. The alternative would be
to trace the gfn instead of hva, but that's not obviously better and
could also be done in common code. Tracing the notifiers is also quite
handy for debug regardless of architecture.
Remove a completely redundant tracepoint from PPC e500.
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210326021957.1424875-10-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Track the range being invalidated by mmu_notifier and skip page fault
retries if the fault address is not affected by the in-progress
invalidation. Handle concurrent invalidations by finding the minimal
range which includes all ranges being invalidated. Although the combined
range may include unrelated addresses and cannot be shrunk as individual
invalidation operations complete, it is unlikely the marginal gains of
proper range tracking are worth the additional complexity.
The primary benefit of this change is the reduction in the likelihood of
extreme latency when handing a page fault due to another thread having
been preempted while modifying host virtual addresses.
Signed-off-by: David Stevens <stevensd@chromium.org>
Message-Id: <20210222024522.1751719-3-stevensd@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Use kvm_pfn_t, a.k.a. u64, for the local 'pfn' variable when retrieving
a so called "remapped" hva/pfn pair. In theory, the hva could resolve to
a pfn in high memory on a 32-bit kernel.
This bug was inadvertantly exposed by commit bd2fae8da7 ("KVM: do not
assume PTE is writable after follow_pfn"), which added an error PFN value
to the mix, causing gcc to comlain about overflowing the unsigned long.
arch/x86/kvm/../../../virt/kvm/kvm_main.c: In function ‘hva_to_pfn_remapped’:
include/linux/kvm_host.h:89:30: error: conversion from ‘long long unsigned int’
to ‘long unsigned int’ changes value from
‘9218868437227405314’ to ‘2’ [-Werror=overflow]
89 | #define KVM_PFN_ERR_RO_FAULT (KVM_PFN_ERR_MASK + 2)
| ^
virt/kvm/kvm_main.c:1935:9: note: in expansion of macro ‘KVM_PFN_ERR_RO_FAULT’
Cc: stable@vger.kernel.org
Fixes: add6a0cd1c ("KVM: MMU: try to fix up page faults before giving up")
Signed-off-by: Sean Christopherson <seanjc@google.com>
Message-Id: <20210208201940.1258328-1-seanjc@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently, the follow_pfn function is exported for modules but
follow_pte is not. However, follow_pfn is very easy to misuse,
because it does not provide protections (so most of its callers
assume the page is writable!) and because it returns after having
already unlocked the page table lock.
Provide instead a simplified version of follow_pte that does
not have the pmdpp and range arguments. The older version
survives as follow_invalidate_pte() for use by fs/dax.c.
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a read / write lock to be used in place of the MMU spinlock on x86.
The rwlock will enable the TDP MMU to handle page faults, and other
operations in parallel in future commits.
Reviewed-by: Peter Feiner <pfeiner@google.com>
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20210202185734.1680553-19-bgardon@google.com>
[Introduce virt/kvm/mmu_lock.h - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
fixed the following warning：
/virt/kvm/dirty_ring.c:70:20-27: WARNING: vzalloc should be used for
ring -> dirty_gfns, instead of vmalloc/memset.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Message-Id: <1611547045-13669-1-git-send-email-tiantao6@hisilicon.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to convert an HVA to a PFN, KVM usually tries to use
the get_user_pages family of functinso. This however is not
possible for VM_IO vmas; in that case, KVM instead uses follow_pfn.
In doing this however KVM loses the information on whether the
PFN is writable. That is usually not a problem because the main
use of VM_IO vmas with KVM is for BARs in PCI device assignment,
however it is a bug. To fix it, use follow_pte and check pte_write
while under the protection of the PTE lock. The information can
be used to fail hva_to_pfn_remapped or passed back to the
caller via *writable.
Usage of follow_pfn was introduced in commit add6a0cd1c ("KVM: MMU: try to fix
up page faults before giving up", 2016-07-05); however, even older version
have the same issue, all the way back to commit 2e2e3738af ("KVM:
Handle vma regions with no backing page", 2008-07-20), as they also did
not check whether the PFN was writable.
Fixes: 2e2e3738af ("KVM: Handle vma regions with no backing page")
Reported-by: David Stevens <stevensd@google.com>
Cc: 3pvd@google.com
Cc: Jann Horn <jannh@google.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Don't allow tagged pointers to point to memslots
- Filter out ARMv8.1+ PMU events on v8.0 hardware
- Hide PMU registers from userspace when no PMU is configured
- More PMU cleanups
- Don't try to handle broken PSCI firmware
- More sys_reg() to reg_to_encoding() conversions
-----BEGIN PGP SIGNATURE-----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=GHVB
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 5.11, take #2
- Don't allow tagged pointers to point to memslots
- Filter out ARMv8.1+ PMU events on v8.0 hardware
- Hide PMU registers from userspace when no PMU is configured
- More PMU cleanups
- Don't try to handle broken PSCI firmware
- More sys_reg() to reg_to_encoding() conversions
The use of a tagged address could be pretty confusing for the
whole memslot infrastructure as well as the MMU notifiers.
Forbid it altogether, as it never quite worked the first place.
Cc: stable@vger.kernel.org
Reported-by: Rick Edgecombe <rick.p.edgecombe@intel.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
* Fixes for the new scalable MMU
* Fixes for migration of nested hypervisors on AMD
* Fix for clang integrated assembler
* Fix for left shift by 64 (UBSAN)
* Small cleanups
* Straggler SEV-ES patch
ARM:
* VM init cleanups
* PSCI relay cleanups
* Kill CONFIG_KVM_ARM_PMU
* Fixup __init annotations
* Fixup reg_to_encoding()
* Fix spurious PMCR_EL0 access
* selftests cleanups
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl/4YOMUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroMg0Qf/eGDOoLL18KhA9MpoPXusR5kU+82G
AcbFj9siNW46EF7mL+sw/xAx+gZaqSpIEmn/f6BzgiaUBdFTv9CKX3B54e43e59G
HAKD0NpqwvDIi1b0T6bcgC92mY3Qx/IDCc7/9JYjBs/iORfqyWW6xVtkF/Gfymxt
eK+MnfMqqNZODgR/cZnCH1E48fuwOvRMxLqilLi3OOMSUfs2cQOSLTNfYQYqjeaJ
dsQ4YeyPJO5JHtfHFr6VPIo/jDhowniac9CNvOomWWVIx2zPYVSl9d8ub6ESEPNF
GM7UeBCOMmZG/a3qFEZPAUJ7znW4yYE85Z6pjxlrGhd1I54MJi4dd+RApw==
=5Nfj
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"x86:
- Fixes for the new scalable MMU
- Fixes for migration of nested hypervisors on AMD
- Fix for clang integrated assembler
- Fix for left shift by 64 (UBSAN)
- Small cleanups
- Straggler SEV-ES patch
ARM:
- VM init cleanups
- PSCI relay cleanups
- Kill CONFIG_KVM_ARM_PMU
- Fixup __init annotations
- Fixup reg_to_encoding()
- Fix spurious PMCR_EL0 access
Misc:
- selftests cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (38 commits)
KVM: x86: __kvm_vcpu_halt can be static
KVM: SVM: Add support for booting APs in an SEV-ES guest
KVM: nSVM: cancel KVM_REQ_GET_NESTED_STATE_PAGES on nested vmexit
KVM: nSVM: mark vmcb as dirty when forcingly leaving the guest mode
KVM: nSVM: correctly restore nested_run_pending on migration
KVM: x86/mmu: Clarify TDP MMU page list invariants
KVM: x86/mmu: Ensure TDP MMU roots are freed after yield
kvm: check tlbs_dirty directly
KVM: x86: change in pv_eoi_get_pending() to make code more readable
MAINTAINERS: Really update email address for Sean Christopherson
KVM: x86: fix shift out of bounds reported by UBSAN
KVM: selftests: Implement perf_test_util more conventionally
KVM: selftests: Use vm_create_with_vcpus in create_vm
KVM: selftests: Factor out guest mode code
KVM/SVM: Remove leftover __svm_vcpu_run prototype from svm.c
KVM: SVM: Add register operand to vmsave call in sev_es_vcpu_load
KVM: x86/mmu: Optimize not-present/MMIO SPTE check in get_mmio_spte()
KVM: x86/mmu: Use raw level to index into MMIO walks' sptes array
KVM: x86/mmu: Get root level from walkers when retrieving MMIO SPTE
KVM: x86/mmu: Use -1 to flag an undefined spte in get_mmio_spte()
...
In kvm_mmu_notifier_invalidate_range_start(), tlbs_dirty is used as:
need_tlb_flush |= kvm->tlbs_dirty;
with need_tlb_flush's type being int and tlbs_dirty's type being long.
It means that tlbs_dirty is always used as int and the higher 32 bits
is useless. We need to check tlbs_dirty in a correct way and this
change checks it directly without propagating it to need_tlb_flush.
Note: it's _extremely_ unlikely this neglecting of higher 32 bits can
cause problems in practice. It would require encountering tlbs_dirty
on a 4 billion count boundary, and KVM would need to be using shadow
paging or be running a nested guest.
Cc: stable@vger.kernel.org
Fixes: a4ee1ca4a3 ("KVM: MMU: delay flush all tlbs on sync_page path")
Signed-off-by: Lai Jiangshan <laijs@linux.alibaba.com>
Message-Id: <20201217154118.16497-1-jiangshanlai@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
* PSCI relay at EL2 when "protected KVM" is enabled
* New exception injection code
* Simplification of AArch32 system register handling
* Fix PMU accesses when no PMU is enabled
* Expose CSV3 on non-Meltdown hosts
* Cache hierarchy discovery fixes
* PV steal-time cleanups
* Allow function pointers at EL2
* Various host EL2 entry cleanups
* Simplification of the EL2 vector allocation
s390:
* memcg accouting for s390 specific parts of kvm and gmap
* selftest for diag318
* new kvm_stat for when async_pf falls back to sync
x86:
* Tracepoints for the new pagetable code from 5.10
* Catch VFIO and KVM irqfd events before userspace
* Reporting dirty pages to userspace with a ring buffer
* SEV-ES host support
* Nested VMX support for wait-for-SIPI activity state
* New feature flag (AVX512 FP16)
* New system ioctl to report Hyper-V-compatible paravirtualization features
Generic:
* Selftest improvements
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl/bdL4UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNgQQgAnTH6rhXa++Zd5F0EM2NwXwz3iEGb
lOq1DZSGjs6Eekjn8AnrWbmVQr+CBCuGU9MrxpSSzNDK/awryo3NwepOWAZw9eqk
BBCVwGBbJQx5YrdgkGC0pDq2sNzcpW/VVB3vFsmOxd9eHblnuKSIxEsCCXTtyqIt
XrLpQ1UhvI4yu102fDNhuFw2EfpzXm+K0Lc0x6idSkdM/p7SyeOxiv8hD4aMr6+G
bGUQuMl4edKZFOWFigzr8NovQAvDHZGrwfihu2cLRYKLhV97QuWVmafv/yYfXcz2
drr+wQCDNzDOXyANnssmviazrhOX0QmTAhbIXGGX/kTxYKcfPi83ZLoI3A==
=ISud
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Much x86 work was pushed out to 5.12, but ARM more than made up for it.
ARM:
- PSCI relay at EL2 when "protected KVM" is enabled
- New exception injection code
- Simplification of AArch32 system register handling
- Fix PMU accesses when no PMU is enabled
- Expose CSV3 on non-Meltdown hosts
- Cache hierarchy discovery fixes
- PV steal-time cleanups
- Allow function pointers at EL2
- Various host EL2 entry cleanups
- Simplification of the EL2 vector allocation
s390:
- memcg accouting for s390 specific parts of kvm and gmap
- selftest for diag318
- new kvm_stat for when async_pf falls back to sync
x86:
- Tracepoints for the new pagetable code from 5.10
- Catch VFIO and KVM irqfd events before userspace
- Reporting dirty pages to userspace with a ring buffer
- SEV-ES host support
- Nested VMX support for wait-for-SIPI activity state
- New feature flag (AVX512 FP16)
- New system ioctl to report Hyper-V-compatible paravirtualization features
Generic:
- Selftest improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (171 commits)
KVM: SVM: fix 32-bit compilation
KVM: SVM: Add AP_JUMP_TABLE support in prep for AP booting
KVM: SVM: Provide support to launch and run an SEV-ES guest
KVM: SVM: Provide an updated VMRUN invocation for SEV-ES guests
KVM: SVM: Provide support for SEV-ES vCPU loading
KVM: SVM: Provide support for SEV-ES vCPU creation/loading
KVM: SVM: Update ASID allocation to support SEV-ES guests
KVM: SVM: Set the encryption mask for the SVM host save area
KVM: SVM: Add NMI support for an SEV-ES guest
KVM: SVM: Guest FPU state save/restore not needed for SEV-ES guest
KVM: SVM: Do not report support for SMM for an SEV-ES guest
KVM: x86: Update __get_sregs() / __set_sregs() to support SEV-ES
KVM: SVM: Add support for CR8 write traps for an SEV-ES guest
KVM: SVM: Add support for CR4 write traps for an SEV-ES guest
KVM: SVM: Add support for CR0 write traps for an SEV-ES guest
KVM: SVM: Add support for EFER write traps for an SEV-ES guest
KVM: SVM: Support string IO operations for an SEV-ES guest
KVM: SVM: Support MMIO for an SEV-ES guest
KVM: SVM: Create trace events for VMGEXIT MSR protocol processing
KVM: SVM: Create trace events for VMGEXIT processing
...
A VCPU of a VM can allocate couple of pages which can be mmap'ed by the
user space application. At the moment this memory is not charged to the
memcg of the VMM. On a large machine running large number of VMs or
small number of VMs having large number of VCPUs, this unaccounted
memory can be very significant. So, charge this memory to the memcg of
the VMM. Please note that lifetime of these allocations corresponds to
the lifetime of the VMM.
Link: https://lkml.kernel.org/r/20201106202923.2087414-1-shakeelb@google.com
Signed-off-by: Shakeel Butt <shakeelb@google.com>
Acked-by: Roman Gushchin <guro@fb.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because kvm dirty rings and kvm dirty log is used in an exclusive way,
Let's avoid creating the dirty_bitmap when kvm dirty ring is enabled.
At the meantime, since the dirty_bitmap will be conditionally created
now, we can't use it as a sign of "whether this memory slot enabled
dirty tracking". Change users like that to check against the kvm
memory slot flags.
Note that there still can be chances where the kvm memory slot got its
dirty_bitmap allocated, _if_ the memory slots are created before
enabling of the dirty rings and at the same time with the dirty
tracking capability enabled, they'll still with the dirty_bitmap.
However it should not hurt much (e.g., the bitmaps will always be
freed if they are there), and the real users normally won't trigger
this because dirty bit tracking flag should in most cases only be
applied to kvm slots only before migration starts, that should be far
latter than kvm initializes (VM starts).
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201001012226.5868-1-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There's no good reason to use both the dirty bitmap logging and the
new dirty ring buffer to track dirty bits. We should be able to even
support both of them at the same time, but it could complicate things
which could actually help little. Let's simply make it the rule
before we enable dirty ring on any arch, that we don't allow these two
interfaces to be used together.
The big world switch would be KVM_CAP_DIRTY_LOG_RING capability
enablement. That's where we'll switch from the default dirty logging
way to the dirty ring way. As long as kvm->dirty_ring_size is setup
correctly, we'll once and for all switch to the dirty ring buffer mode
for the current virtual machine.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201001012224.5818-1-peterx@redhat.com>
[Change errno from EINVAL to ENXIO. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch is heavily based on previous work from Lei Cao
<lei.cao@stratus.com> and Paolo Bonzini <pbonzini@redhat.com>. [1]
KVM currently uses large bitmaps to track dirty memory. These bitmaps
are copied to userspace when userspace queries KVM for its dirty page
information. The use of bitmaps is mostly sufficient for live
migration, as large parts of memory are be dirtied from one log-dirty
pass to another. However, in a checkpointing system, the number of
dirty pages is small and in fact it is often bounded---the VM is
paused when it has dirtied a pre-defined number of pages. Traversing a
large, sparsely populated bitmap to find set bits is time-consuming,
as is copying the bitmap to user-space.
A similar issue will be there for live migration when the guest memory
is huge while the page dirty procedure is trivial. In that case for
each dirty sync we need to pull the whole dirty bitmap to userspace
and analyse every bit even if it's mostly zeros.
The preferred data structure for above scenarios is a dense list of
guest frame numbers (GFN). This patch series stores the dirty list in
kernel memory that can be memory mapped into userspace to allow speedy
harvesting.
This patch enables dirty ring for X86 only. However it should be
easily extended to other archs as well.
[1] https://patchwork.kernel.org/patch/10471409/
Signed-off-by: Lei Cao <lei.cao@stratus.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201001012222.5767-1-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The context will be needed to implement the kvm dirty ring.
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201001012044.5151-5-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_clear_guest_page is not used anymore after "KVM: X86: Don't track dirty
for KVM_SET_[TSS_ADDR|IDENTITY_MAP_ADDR]", except from kvm_clear_guest.
We can just inline it in its sole user.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Don't allow the events to accumulate in the eventfd counter, drain them
as they are handled.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20201027135523.646811-4-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
As far as I can tell, when we use posted interrupts we silently cut off
the events from userspace, if it's listening on the same eventfd that
feeds the irqfd.
I like that behaviour. Let's do it all the time, even without posted
interrupts. It makes it much easier to handle IRQ remapping invalidation
without having to constantly add/remove the fd from the userspace poll
set. We can just leave userspace polling on it, and the bypass will...
well... bypass it.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Message-Id: <20201026175325.585623-2-dwmw2@infradead.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Dirty logging is a key feature of the KVM MMU and must be supported by
the TDP MMU. Add support for both the write protection and PML dirty
logging modes.
Tested by running kvm-unit-tests and KVM selftests on an Intel Haswell
machine. This series introduced no new failures.
This series can be viewed in Gerrit at:
https://linux-review.googlesource.com/c/virt/kvm/kvm/+/2538
Signed-off-by: Ben Gardon <bgardon@google.com>
Message-Id: <20201014182700.2888246-16-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Cache the address space ID just like the slot ID. It will be used in
order to fill in the dirty ring entries.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Sean Christopherson <sean.j.christopherson@intel.com>
Reviewed-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20201014182700.2888246-7-bgardon@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make use of the struct_size() helper to avoid any potential type
mistakes and protect against potential integer overflows
Make use of the flex_array_size() helper to calculate the size of a
flexible array member within an enclosing structure
Suggested-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
Message-Id: <20200918120500.954436-1-rkovhaev@gmail.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There is no need to calculate wildcard in each iteration
since wildcard is not changed.
Signed-off-by: Yi Li <yili@winhong.com>
Message-Id: <20200911055652.3041762-1-yili@winhong.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
when kmalloc() fails in kvm_io_bus_unregister_dev(), before removing
the bus, we should iterate over all other devices linked to it and call
kvm_iodevice_destructor() for them
Fixes: 90db10434b ("KVM: kvm_io_bus_unregister_dev() should never fail")
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+f196caa45793d6374707@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=f196caa45793d6374707
Signed-off-by: Rustam Kovhaev <rkovhaev@gmail.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Message-Id: <20200907185535.233114-1-rkovhaev@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Multiple stolen time fixes, with a new capability to match x86
- Fix for hugetlbfs mappings when PUD and PMD are the same level
- Fix for hugetlbfs mappings when PTE mappings are enforced
(dirty logging, for example)
- Fix tracing output of 64bit values
-----BEGIN PGP SIGNATURE-----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=VBrL
-----END PGP SIGNATURE-----
Merge tag 'kvmarm-fixes-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for Linux 5.9, take #1
- Multiple stolen time fixes, with a new capability to match x86
- Fix for hugetlbfs mappings when PUD and PMD are the same level
- Fix for hugetlbfs mappings when PTE mappings are enforced
(dirty logging, for example)
- Fix tracing output of 64bit values
The 'flags' field of 'struct mmu_notifier_range' is used to indicate
whether invalidate_range_{start,end}() are permitted to block. In the
case of kvm_mmu_notifier_invalidate_range_start(), this field is not
forwarded on to the architecture-specific implementation of
kvm_unmap_hva_range() and therefore the backend cannot sensibly decide
whether or not to block.
Add an extra 'flags' parameter to kvm_unmap_hva_range() so that
architectures are aware as to whether or not they are permitted to block.
Cc: <stable@vger.kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Message-Id: <20200811102725.7121-2-will@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Merge more updates from Andrew Morton:
- most of the rest of MM (memcg, hugetlb, vmscan, proc, compaction,
mempolicy, oom-kill, hugetlbfs, migration, thp, cma, util,
memory-hotplug, cleanups, uaccess, migration, gup, pagemap),
- various other subsystems (alpha, misc, sparse, bitmap, lib, bitops,
checkpatch, autofs, minix, nilfs, ufs, fat, signals, kmod, coredump,
exec, kdump, rapidio, panic, kcov, kgdb, ipc).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (164 commits)
mm/gup: remove task_struct pointer for all gup code
mm: clean up the last pieces of page fault accountings
mm/xtensa: use general page fault accounting
mm/x86: use general page fault accounting
mm/sparc64: use general page fault accounting
mm/sparc32: use general page fault accounting
mm/sh: use general page fault accounting
mm/s390: use general page fault accounting
mm/riscv: use general page fault accounting
mm/powerpc: use general page fault accounting
mm/parisc: use general page fault accounting
mm/openrisc: use general page fault accounting
mm/nios2: use general page fault accounting
mm/nds32: use general page fault accounting
mm/mips: use general page fault accounting
mm/microblaze: use general page fault accounting
mm/m68k: use general page fault accounting
mm/ia64: use general page fault accounting
mm/hexagon: use general page fault accounting
mm/csky: use general page fault accounting
...
After the cleanup of page fault accounting, gup does not need to pass
task_struct around any more. Remove that parameter in the whole gup
stack.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: John Hubbard <jhubbard@nvidia.com>
Link: http://lkml.kernel.org/r/20200707225021.200906-26-peterx@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
IRQ bypass support for vdpa and IFC
MLX5 vdpa driver
Endian-ness fixes for virtio drivers
Misc other fixes
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAl8yVEwPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpNPEH/0Dtq1s1V4r/kxtLUoMophv9wuORpWCr98BQ
2aOveTmwTOVdZVOiw2tzTgO9nbWx+cL2HvkU7Aajfpz5hh93Z2VOo2n4a7hBC79f
rlc3GXiG+pMk5RfmqGofIHTU+D6ony4D5SXlUDurLdtEwunyuqZwABiWkZjdclZJ
bv90IL8Upzbz0rxYr7k3z8UepdOCt7r4QS/o7STHZBjJRyylxmO/R2yTnh6PtpRK
Q/z35wJBJ3SKc8X3Fi0VOOSeGNZOiypkkl9ZnLVY5lExNAU1+2MMn2UK119SlCDV
MSxb7quYFF4cksXH1g77GMBNi1uADRh1dtFMZdkKhZGljGxKLxo=
=6VTZ
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
- IRQ bypass support for vdpa and IFC
- MLX5 vdpa driver
- Endianness fixes for virtio drivers
- Misc other fixes
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (71 commits)
vdpa/mlx5: fix up endian-ness for mtu
vdpa: Fix pointer math bug in vdpasim_get_config()
vdpa/mlx5: Fix pointer math in mlx5_vdpa_get_config()
vdpa/mlx5: fix memory allocation failure checks
vdpa/mlx5: Fix uninitialised variable in core/mr.c
vdpa_sim: init iommu lock
virtio_config: fix up warnings on parisc
vdpa/mlx5: Add VDPA driver for supported mlx5 devices
vdpa/mlx5: Add shared memory registration code
vdpa/mlx5: Add support library for mlx5 VDPA implementation
vdpa/mlx5: Add hardware descriptive header file
vdpa: Modify get_vq_state() to return error code
net/vdpa: Use struct for set/get vq state
vdpa: remove hard coded virtq num
vdpasim: support batch updating
vhost-vdpa: support IOTLB batching hints
vhost-vdpa: support get/set backend features
vhost: generialize backend features setting/getting
vhost-vdpa: refine ioctl pre-processing
vDPA: dont change vq irq after DRIVER_OK
...
- Untangle the header spaghetti which causes build failures in various
situations caused by the lockdep additions to seqcount to validate that
the write side critical sections are non-preemptible.
- The seqcount associated lock debug addons which were blocked by the
above fallout.
seqcount writers contrary to seqlock writers must be externally
serialized, which usually happens via locking - except for strict per
CPU seqcounts. As the lock is not part of the seqcount, lockdep cannot
validate that the lock is held.
This new debug mechanism adds the concept of associated locks.
sequence count has now lock type variants and corresponding
initializers which take a pointer to the associated lock used for
writer serialization. If lockdep is enabled the pointer is stored and
write_seqcount_begin() has a lockdep assertion to validate that the
lock is held.
Aside of the type and the initializer no other code changes are
required at the seqcount usage sites. The rest of the seqcount API is
unchanged and determines the type at compile time with the help of
_Generic which is possible now that the minimal GCC version has been
moved up.
Adding this lockdep coverage unearthed a handful of seqcount bugs which
have been addressed already independent of this.
While generaly useful this comes with a Trojan Horse twist: On RT
kernels the write side critical section can become preemtible if the
writers are serialized by an associated lock, which leads to the well
known reader preempts writer livelock. RT prevents this by storing the
associated lock pointer independent of lockdep in the seqcount and
changing the reader side to block on the lock when a reader detects
that a writer is in the write side critical section.
- Conversion of seqcount usage sites to associated types and initializers.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl8xmPYTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoTuQEACyzQCjU8PgehPp9oMqWzaX2fcVyuZO
QU2yw6gmz2oTz3ZHUNwdW8UnzGh2OWosK3kDruoD9FtSS51lER1/ISfSPCGfyqxC
KTjOcB1Kvxwq/3LcCx7Zi3ZxWApat74qs3EhYhKtEiQ2Y9xv9rLq8VV1UWAwyxq0
eHpjlIJ6b6rbt+ARslaB7drnccOsdK+W/roNj4kfyt+gezjBfojGRdMGQNMFcpnv
shuTC+vYurAVIiVA/0IuizgHfwZiXOtVpjVoEWaxg6bBH6HNuYMYzdSa/YrlDkZs
n/aBI/Xkvx+Eacu8b1Zwmbzs5EnikUK/2dMqbzXKUZK61eV4hX5c2xrnr1yGWKTs
F/juh69Squ7X6VZyKVgJ9RIccVueqwR2EprXWgH3+RMice5kjnXH4zURp0GHALxa
DFPfB6fawcH3Ps87kcRFvjgm6FBo0hJ1AxmsW1dY4ACFB9azFa2euW+AARDzHOy2
VRsUdhL9CGwtPjXcZ/9Rhej6fZLGBXKr8uq5QiMuvttp4b6+j9FEfBgD4S6h8csl
AT2c2I9LcbWqyUM9P4S7zY/YgOZw88vHRuDH7tEBdIeoiHfrbSBU7EQ9jlAKq/59
f+Htu2Io281c005g7DEeuCYvpzSYnJnAitj5Lmp/kzk2Wn3utY1uIAVszqwf95Ul
81ppn2KlvzUK8g==
=7Gj+
-----END PGP SIGNATURE-----
Merge tag 'locking-urgent-2020-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Thomas Gleixner:
"A set of locking fixes and updates:
- Untangle the header spaghetti which causes build failures in
various situations caused by the lockdep additions to seqcount to
validate that the write side critical sections are non-preemptible.
- The seqcount associated lock debug addons which were blocked by the
above fallout.
seqcount writers contrary to seqlock writers must be externally
serialized, which usually happens via locking - except for strict
per CPU seqcounts. As the lock is not part of the seqcount, lockdep
cannot validate that the lock is held.
This new debug mechanism adds the concept of associated locks.
sequence count has now lock type variants and corresponding
initializers which take a pointer to the associated lock used for
writer serialization. If lockdep is enabled the pointer is stored
and write_seqcount_begin() has a lockdep assertion to validate that
the lock is held.
Aside of the type and the initializer no other code changes are
required at the seqcount usage sites. The rest of the seqcount API
is unchanged and determines the type at compile time with the help
of _Generic which is possible now that the minimal GCC version has
been moved up.
Adding this lockdep coverage unearthed a handful of seqcount bugs
which have been addressed already independent of this.
While generally useful this comes with a Trojan Horse twist: On RT
kernels the write side critical section can become preemtible if
the writers are serialized by an associated lock, which leads to
the well known reader preempts writer livelock. RT prevents this by
storing the associated lock pointer independent of lockdep in the
seqcount and changing the reader side to block on the lock when a
reader detects that a writer is in the write side critical section.
- Conversion of seqcount usage sites to associated types and
initializers"
* tag 'locking-urgent-2020-08-10' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (25 commits)
locking/seqlock, headers: Untangle the spaghetti monster
locking, arch/ia64: Reduce <asm/smp.h> header dependencies by moving XTP bits into the new <asm/xtp.h> header
x86/headers: Remove APIC headers from <asm/smp.h>
seqcount: More consistent seqprop names
seqcount: Compress SEQCNT_LOCKNAME_ZERO()
seqlock: Fold seqcount_LOCKNAME_init() definition
seqlock: Fold seqcount_LOCKNAME_t definition
seqlock: s/__SEQ_LOCKDEP/__SEQ_LOCK/g
hrtimer: Use sequence counter with associated raw spinlock
kvm/eventfd: Use sequence counter with associated spinlock
userfaultfd: Use sequence counter with associated spinlock
NFSv4: Use sequence counter with associated spinlock
iocost: Use sequence counter with associated spinlock
raid5: Use sequence counter with associated spinlock
vfs: Use sequence counter with associated spinlock
timekeeping: Use sequence counter with associated raw spinlock
xfrm: policy: Use sequence counters with associated lock
netfilter: nft_set_rbtree: Use sequence counter with associated rwlock
netfilter: conntrack: Use sequence counter with associated spinlock
sched: tasks: Use sequence counter with associated spinlock
...
x86:
* Report last CPU for debugging
* Emulate smaller MAXPHYADDR in the guest than in the host
* .noinstr and tracing fixes from Thomas
* nested SVM page table switching optimization and fixes
Generic:
* Unify shadow MMU cache data structures across architectures
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl8pC+oUHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNcOwgAjomqtEqQNlp7DdZT7VyyklzbxX1/
ud7v+oOJ8K4sFlf64lSthjPo3N9rzZCcw+yOXmuyuITngXOGc3tzIwXpCzpLtuQ1
WO1Ql3B/2dCi3lP5OMmsO1UAZqy9pKLg1dfeYUPk48P5+p7d/NPmk+Em5kIYzKm5
JsaHfCp2EEXomwmljNJ8PQ1vTjIQSSzlgYUBZxmCkaaX7zbEUMtxAQCStHmt8B84
33LczwXBm3viSWrzsoBV37I70+tseugiSGsCfUyupXOvq55d6D9FCqtCb45Hn4Vh
Ik8ggKdalsk/reiGEwNw1/3nr6mRMkHSbl+Mhc4waOIFf9dn0urgQgOaDg==
=YVx0
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"s390:
- implement diag318
x86:
- Report last CPU for debugging
- Emulate smaller MAXPHYADDR in the guest than in the host
- .noinstr and tracing fixes from Thomas
- nested SVM page table switching optimization and fixes
Generic:
- Unify shadow MMU cache data structures across architectures"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (127 commits)
KVM: SVM: Fix sev_pin_memory() error handling
KVM: LAPIC: Set the TDCR settable bits
KVM: x86: Specify max TDP level via kvm_configure_mmu()
KVM: x86/mmu: Rename max_page_level to max_huge_page_level
KVM: x86: Dynamically calculate TDP level from max level and MAXPHYADDR
KVM: VXM: Remove temporary WARN on expected vs. actual EPTP level mismatch
KVM: x86: Pull the PGD's level from the MMU instead of recalculating it
KVM: VMX: Make vmx_load_mmu_pgd() static
KVM: x86/mmu: Add separate helper for shadow NPT root page role calc
KVM: VMX: Drop a duplicate declaration of construct_eptp()
KVM: nSVM: Correctly set the shadow NPT root level in its MMU role
KVM: Using macros instead of magic values
MIPS: KVM: Fix build error caused by 'kvm_run' cleanup
KVM: nSVM: remove nonsensical EXITINFO1 adjustment on nested NPF
KVM: x86: Add a capability for GUEST_MAXPHYADDR < HOST_MAXPHYADDR support
KVM: VMX: optimize #PF injection when MAXPHYADDR does not match
KVM: VMX: Add guest physical address check in EPT violation and misconfig
KVM: VMX: introduce vmx_need_pf_intercept
KVM: x86: update exception bitmap on CPUID changes
KVM: x86: rename update_bp_intercept to update_exception_bitmap
...
