Pull perf fixes from Ingo Molnar:
"A bogus warning fix, a counter width handling fix affecting certain
machines, plus a oneliner hw-enablement patch for Knights Mill CPUs"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/core: Remove invalid warning from list_update_cgroup_even()t
perf/x86: Fix full width counter, counter overflow
perf/x86/intel: Enable C-state residency events for Knights Mill
Pull locking fixes from Ingo Molnar:
"Two rtmutex race fixes (which miraculously never triggered, that we
know of), plus two lockdep printk formatting regression fixes"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Fix report formatting
locking/rtmutex: Use READ_ONCE() in rt_mutex_owner()
locking/rtmutex: Prevent dequeue vs. unlock race
locking/selftest: Fix output since KERN_CONT changes
Pull objtool fix from Ingo Molnar:
"A single late breaking fix for objtool"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix bytes check of lea's rex_prefix
Commit 3e3aaf6494 ("phy: fix mdiobus module safety") fixed the way we
dealt with MDIO bus module reference count, but sort of introduced a
regression in that, if an Ethernet driver registers its own MDIO bus
driver, as is common, we will end up with the Ethernet driver's
module->refnct set to 1, thus preventing this driver from any removal.
Fix this by comparing the network device's device driver owner against
the MDIO bus driver owner, and only if they are different, increment the
MDIO bus module refcount.
Fixes: 3e3aaf6494 ("phy: fix mdiobus module safety")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hyper-V (and Azure) support using NVGRE which requires some extra space
for encapsulation headers. Because of this the largest allowed TSO
packet is reduced.
For older releases, hard code a fixed reduced value. For next release,
there is a better solution which uses result of host offload
negotiation.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for setting the RGMII_IDMODE bit was added in the commit
referenced below. However, that commit did not add the symmetrical
clearing of the bit by way of setting it in "mask". Add it here.
Note that the documentation marks clearing this bit as "reserved",
however, according to TI, support for delaying the clock does exist in
the MAC, although it is not officially supported.
We tested this on a board with an RGMII to RGMII link that will not
work unless this bit is cleared.
Fixes: 0fb26c3063 ("drivers: net: cpsw-phy-sel: add support to configure rgmii internal delay")
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAlhH2rkTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklasABCAClCaAGYAOuMLWXJ9mL1K7o2u+s6M93
bSZQfke8ffFv0vNa35HLH8vXCh3QBl8BEZkN0XuXQwRSiewsWQz/W5hMZ9UcfgdR
lml6v/jaQ0nai5UrdSHJqXwm21e3M/ELFn5dE0esp1p7lSITRAbTPSyN2kNhiGyv
HLMXFPopCGEbInyo+5QA17xTPGUdMNE6J8rnRPKnMzbLgyRgZ3Jwy0furKAbzTY7
4eFiERuBErRB/tD3+oxFICcB5zyvqawnXZp+gsg5o8vm7DGZU4/WXbxOQOgwx1fK
Nw4/9FXPxUxXB925JMIn/bxjNi0OK9M96Q7bMpoa8Ik/CCkV/zKdKxIt
=0RcO
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.9-20161207' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-12-07
Andrey Konovalov triggered a warning in the CAN RAW layer, which is
fixed by a patch by me.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull fuse fix from Miklos Szeredi:
"Fix a regression spotted by Jeff Layton"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix clearing suid, sgid for chown()
This reverts commit 8ab2ae655b.
I loved that commit because of how it explained what the problem with
newer versions of binutils were, but the actual patch itself turns out
to not work very well.
It has two problems:
- a zero CRC value isn't actually right. It happens to work for the
case where both sides of the equation fail at giving the symbol a
crc, but there are cases where the users of the exported symbol get
the right crc (due to seeing the C declarations), but the actual
exporting itself does not (due to the whole weak asm symbol issue).
So then the module load fails after all - we did have a crc for the
symbol, but we couldn't match it with the loaded module.
- it seems that the alpha assembler has special semantics for the
'.set' directive, and on alpha it doesn't actually set the value of
the specified symbol at all, it is instead used to set various
assembly modes (eg ".set noat" and ".set noreorder").
So using ".set" to set the symbol value would just cause build
failures on alpha.
I'm sure we'll find some other workaround for these issues (hopefully
that involves getting rid of modversions entirely some day, but people
are also talking about just using smarter tools). But for now we'll
just fall back on commit faaae2a581 ("Re-enable CONFIG_MODVERSIONS in
a slightly weaker form") that just let's a missing crc through.
Reported-by: Jan Stancek <jstancek@redhat.com>
Reported-by: Philip Müller <philm@manjaro.org>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In theory we could map other things, but there's a reason that function
is called "user_iov". Using anything else (like splice can do) just
confuses it.
Reported-and-tested-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Algorithms not compatible with mcryptd could be spawned by mcryptd
with a direct crypto_alloc_tfm invocation using a "mcryptd(alg)" name
construct. This causes mcryptd to crash the kernel if an arbitrary
"alg" is incompatible and not intended to be used with mcryptd. It is
an issue if AF_ALG tries to spawn mcryptd(alg) to expose it externally.
But such algorithms must be used internally and not be exposed.
We added a check to enforce that only internal algorithms are allowed
with mcryptd at the time mcryptd is spawning an algorithm.
Link: http://marc.info/?l=linux-crypto-vger&m=148063683310477&w=2
Cc: stable@vger.kernel.org
Reported-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For encryption, the AEAD ciphers require AAD || PT as input and generate
AAD || CT || Tag as output and vice versa for decryption. Prior to this
patch, the AF_ALG interface for AEAD ciphers requires the buffer to be
present as input for encryption. Similarly, the output buffer for
decryption required the presence of the tag buffer too. This implies
that the kernel reads / writes data buffers from/to kernel space
even though this operation is not required.
This patch changes the AF_ALG AEAD interface to be consistent with the
in-kernel AEAD cipher requirements.
Due to this handling, he changes are transparent to user space with one
exception: the return code of recv indicates the mount of output buffer.
That output buffer has a different size compared to before the patch
which implies that the return code of recv will also be different.
For example, a decryption operation uses 16 bytes AAD, 16 bytes CT and
16 bytes tag, the AF_ALG AEAD interface before showed a recv return
code of 48 (bytes) whereas after this patch, the return code is 32
since the tag is not returned any more.
Reported-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Start with a clean slate before dealing with bit 16 (pointer size)
of Master Configuration Register.
This fixes the case of AArch64 boot loader + AArch32 kernel, when
the boot loader might set MCFGR[PS] and kernel would fail to clear it.
Cc: <stable@vger.kernel.org>
Reported-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-By: Alison Wang <Alison.wang@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
mv_cesa_hash_std_step() copies the creq->state into the SRAM at each
step, but this is only required on the first one. By doing that, we
overwrite the engine state, and get erroneous results when the crypto
request is split in several chunks to fit in the internal SRAM.
This commit changes the function to copy the state only on the first
step.
Fixes: commit 2786cee8e5 ("crypto: marvell - Move SRAM I/O op...")
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
No need to copy the template of an hash operation twice into the SRAM
from the step function.
Fixes: commit 85030c5168 ("crypto: marvell - Add support for chai...")
Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds a check to limit the number of can_filters that can be
set via setsockopt on CAN_RAW sockets. Otherwise allocations > MAX_ORDER
are not prevented resulting in a warning.
Reference: https://lkml.org/lkml/2016/12/2/230
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We have four routines in pacache.S that use temporary alias pages:
copy_user_page_asm(), clear_user_page_asm(), flush_dcache_page_asm() and
flush_icache_page_asm(). copy_user_page_asm() and clear_user_page_asm()
don't purge the TLB entry used for the operation.
flush_dcache_page_asm() and flush_icache_page_asm do purge the entry.
Presumably, this was thought to optimize TLB use. However, the
operation is quite heavy weight on PA 1.X processors as we need to take
the TLB lock and a TLB broadcast is sent to all processors.
This patch removes the purges from flush_dcache_page_asm() and
flush_icache_page_asm.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Helge Deller <deller@gmx.de>
The attached change interchanges the order of purging the TLB and
setting the corresponding page table entry. TLB purges are strongly
ordered. It occurred to me one night that setting the PTE first might
have subtle ordering issues on SMP machines and cause random memory
corruption.
A TLB lock guards the insertion of user TLB entries. So after the TLB
is purged, a new entry can't be inserted until the lock is released.
This ensures that the new PTE value is used when the lock is released.
Since making this change, no random segmentation faults have been
observed on the Debian hppa buildd servers.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Helge Deller <deller@gmx.de>
Hugh notes in response to commit 4cb19355ea "device-dax: fail all
private mapping attempts":
"I think that is more restrictive than you intended: haven't tried, but I
believe it rejects a PROT_READ, MAP_SHARED, O_RDONLY fd mmap, leaving no
way to mmap /dev/dax without write permission to it."
Indeed it does restrict read-only mappings, switch to checking
VM_MAYSHARE, not VM_SHARED.
Cc: <stable@vger.kernel.org>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Pawel Lebioda <pawel.lebioda@intel.com>
Fixes: 4cb19355ea ("device-dax: fail all private mapping attempts")
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
A recent flurry of bug discoveries in the nfit driver's DSM marshalling
routine has highlighted the fact that we do not have unit test coverage
for this routine. Add a self-test of acpi_nfit_ctl() routine before
probing the "nfit_test.0" device. This mocks stimulus to acpi_nfit_ctl()
and if any of the tests fail "nfit_test.0" will be unavailable causing
the rest of the tests to not run / fail.
This unit test will also be a place to land reproductions of quirky BIOS
behavior discovered in the field and ensure the kernel does not regress
against implementations it has seen in practice.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Given dimms and bus commands share the same command number space we need
to be careful that we are translating status in the correct context.
Otherwise we can, for example, fail an ND_CMD_GET_CONFIG_SIZE command
because max_xfer is zero. It fails because that condition erroneously
correlates with the 'cleared == 0' failure of ND_CMD_CLEAR_ERROR.
Cc: <stable@vger.kernel.org>
Fixes: aef2533822 ("libnvdimm, nfit: centralize command status translation")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
If an ARS Status command returns truncated output, do not process
partial records or otherwise consume non-status fields.
Cc: <stable@vger.kernel.org>
Fixes: 0caeef63e6 ("libnvdimm: Add a poison list and export badblocks")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Given ambiguities in the ACPI 6.1 definition of the "Output (Size)"
field of the ARS (Address Range Scrub) Status command, a firmware
implementation may in practice return 0, 4, or 8 to indicate that there
is no output payload to process.
The specification states "Size of Output Buffer in bytes, including this
field.". However, 'Output Buffer' is also the name of the entire
payload, and earlier in the specification it states "Max Query ARS
Status Output Buffer Size: Maximum size of buffer (including the Status
and Extended Status fields)".
Without this fix if the BIOS happens to return 0 it causes memory
corruption as evidenced by this result from the acpi_nfit_ctl() unit
test.
ars_status00000000: 00020000 00000000 ........
BUG: stack guard page was hit at ffffc90001750000 (stack is ffffc9000174c000..ffffc9000174ffff)
kernel stack overflow (page fault): 0000 [#1] SMP DEBUG_PAGEALLOC
task: ffff8803332d2ec0 task.stack: ffffc9000174c000
RIP: 0010:[<ffffffff814cfe72>] [<ffffffff814cfe72>] __memcpy+0x12/0x20
RSP: 0018:ffffc9000174f9a8 EFLAGS: 00010246
RAX: ffffc9000174fab8 RBX: 0000000000000000 RCX: 000000001fffff56
RDX: 0000000000000000 RSI: ffff8803231f5a08 RDI: ffffc90001750000
RBP: ffffc9000174fa88 R08: ffffc9000174fab0 R09: ffff8803231f54b8
R10: 0000000000000008 R11: 0000000000000001 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000003 R15: ffff8803231f54a0
FS: 00007f3a611af640(0000) GS:ffff88033ed00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffc90001750000 CR3: 0000000325b20000 CR4: 00000000000406e0
Stack:
ffffffffa00bc60d 0000000000000008 ffffc90000000001 ffffc9000174faac
0000000000000292 ffffffffa00c24e4 ffffffffa00c2914 0000000000000000
0000000000000000 ffffffff00000003 ffff880331ae8ad0 0000000800000246
Call Trace:
[<ffffffffa00bc60d>] ? acpi_nfit_ctl+0x49d/0x750 [nfit]
[<ffffffffa01f4fe0>] nfit_test_probe+0x670/0xb1b [nfit_test]
Cc: <stable@vger.kernel.org>
Fixes: 747ffe11b4 ("libnvdimm, tools/testing/nvdimm: fix 'ars_status' output buffer sizing")
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
ACPI DSMs can have an 'extended' status which can be non-zero to convey
additional information about the command. In the xlat_status routine,
where we translate the command statuses, we were returning an error for
a non-zero extended status, even if the primary status indicated success.
Return from each command's 'case' once we have verified both its status
and extend status are good.
Cc: <stable@vger.kernel.org>
Fixes: 11294d63ac ("nfit: fail DSMs that return non-zero status by default")
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Pull sparc fix from David Miller:
"A use-before-NULL-check from Dan Carpenter"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
dbri: move dereference after check for NULL
We accidentally introduced a dereference before the NULL check in
xmit_descs() as part of silencing a GCC warning.
Fixes: 16f46050e7 ("dbri: Fix compiler warning")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) When dcbnl_cee_fill() fails to be able to push a new netlink
attribute, it return 0 instead of an error code. From Pan Bian.
2) Two suffix handling fixes to FIB trie code, from Alexander Duyck.
3) bnxt_hwrm_stat_ctx_alloc() goes through all the trouble of setting
and maintaining a return code 'rc' but fails to actually return it.
Also from Pan Bian.
4) ping socket ICMP handler needs to validate ICMP header length, from
Kees Cook.
5) caif_sktinit_module() has this interesting logic:
int err = sock_register(...);
if (!err)
return err;
return 0;
Just return sock_register()'s return value directly which is the
only possible correct thing to do.
6) Two bnx2x driver fixes from Yuval Mintz, return a reasonable
estimate from get_ringparam() ethtool op when interface is down and
avoid trying to use UDP port based tunneling on 577xx chips.
7) Fix ep93xx_eth crash on module unload from Florian Fainelli.
8) Missing uapi exports, from Stephen Hemminger.
9) Don't schedule work from sk_destruct(), because the socket will be
freed upon return from that function. From Herbert Xu.
10) Buggy drivers, of which we know there is at least one, can send a
huge packet into the TCP stack but forget to set the gso_size in the
SKB, which causes all kinds of problems.
Correct this when it happens, and emit a one-time warning with the
device name included so that it can be diagnosed more easily.
From Marcelo Ricardo Leitner.
11) virtio-net does DMA off the stack causes hiccups with VMAP_STACK,
fix from Andy Lutomirski.
12) Fix fec driver compilation with CONFIG_M5272, from Nikita
Yushchenko.
13) mlx5 fixes from Kamal Heib, Saeed Mahameed, and Mohamad Haj Yahia.
(erroneously flushing queues on error, module parameter validation,
etc)
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
net/mlx5e: Change the SQ/RQ operational state to positive logic
net/mlx5e: Don't flush SQ on error
net/mlx5e: Don't notify HW when filling the edge of ICO SQ
net/mlx5: Fix query ISSI flow
net/mlx5: Remove duplicate pci dev name print
net/mlx5: Verify module parameters
net: fec: fix compile with CONFIG_M5272
be2net: Add DEVSEC privilege to SET_HSW_CONFIG command.
virtio-net: Fix DMA-from-the-stack in virtnet_set_mac_address()
tcp: warn on bogus MSS and try to amend it
uapi glibc compat: fix outer guard of net device flags enum
net: stmmac: clear reset value of snps, wr_osr_lmt/snps, rd_osr_lmt before writing
netlink: Do not schedule work from sk_destruct
uapi: export nf_log.h
uapi: export tc_skbmod.h
net: ep93xx_eth: Do not crash unloading module
bnx2x: Prevent tunnel config for 577xx
bnx2x: Correct ringparam estimate when DOWN
isdn: hisax: set error code on failure
net: bnx2x: fix improper return value
...
The shmem hole punching with fallocate(FALLOC_FL_PUNCH_HOLE) does not
want to race with generating new pages by faulting them in.
However, the wait-queue used to delay the page faulting has a serious
problem: the wait queue head (in shmem_fallocate()) is allocated on the
stack, and the code expects that "wake_up_all()" will make sure that all
the queue entries are gone before the stack frame is de-allocated.
And that is not at all necessarily the case.
Yes, a normal wake-up sequence will remove the wait-queue entry that
caused the wakeup (see "autoremove_wake_function()"), but the key
wording there is "that caused the wakeup". When there are multiple
possible wakeup sources, the wait queue entry may well stay around.
And _particularly_ in a page fault path, we may be faulting in new pages
from user space while we also have other things going on, and there may
well be other pending wakeups.
So despite the "wake_up_all()", it's not at all guaranteed that all list
entries are removed from the wait queue head on the stack.
Fix this by introducing a new wakeup function that removes the list
entry unconditionally, even if the target process had already woken up
for other reasons. Use that "synchronous" function to set up the
waiters in shmem_fault().
This problem has never been seen in the wild afaik, but Dave Jones has
reported it on and off while running trinity. We thought we fixed the
stack corruption with the blk-mq rq_list locking fix (commit
7fe311302f7d: "blk-mq: update hardware and software queues for sleeping
alloc"), but it turns out there was _another_ stack corruptor hiding
in the trinity runs.
Vegard Nossum (also running trinity) was able to trigger this one fairly
consistently, and made us look once again at the shmem code due to the
faults often being in that area.
Reported-and-tested-by: Vegard Nossum <vegard.nossum@oracle.com>.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Saeed Mahameed says:
====================
Mellanox 100G mlx5 fixes 2016-12-04
Some bug fixes for mlx5 core and mlx5e driver.
v1->v2:
- replace "uint" with "unsigned int"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When using the negative logic (i.e. FLUSH state), after the RQ/SQ reopen
we will have a time interval that the RQ/SQ is not really ready and the
state indicates that its not in FLUSH state because the initial SQ/RQ struct
memory starts as zeros.
Now we changed the state to indicate if the SQ/RQ is opened and we will
set the READY state after finishing preparing all the SQ/RQ resources.
Fixes: 6e8dd6d6f4 ("net/mlx5e: Don't wait for SQ completions on close")
Fixes: f2fde18c52 ("net/mlx5e: Don't wait for RQ completions on close")
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are doing SQ descriptors cleanup in driver.
Fixes: 6e8dd6d6f4 ("net/mlx5e: Don't wait for SQ completions on close")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to do this a couple of steps ahead anyway.
Fixes: d3c9bc2743 ("net/mlx5e: Added ICO SQs")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In old FWs query ISSI command is not supported and for some of those FWs
it might fail with status other than "MLX5_CMD_STAT_BAD_OP_ERR".
In such case instead of failing the driver load, we will treat any FW
status other than 0 for Query ISSI FW command as ISSI not supported and
assume ISSI=0 (most basic driver/FW interface).
In case of driver syndrom (query ISSI failure by driver) we will fail
driver load.
Fixes: f62b8bb8f2 ('net/mlx5: Extend mlx5_core to support ConnectX-4
Ethernet functionality')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove duplicate pci dev name printing from mlx5_core_warn/dbg.
Fixes: 5a7883989b ('net/mlx5_core: Improve mlx5 messages')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify the mlx5_core module parameters by making sure that they are in
the expected range and if they aren't restore them to their default
values.
Fixes: 9603b61de1 ('mlx5: Move pci device handling from mlx5_ib to mlx5_core')
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 80cca775cd ("net: fec: cache statistics while device is down")
introduced unconditional statistics-related actions.
However, when driver is compiled with CONFIG_M5272, staticsics-related
definitions do not exist, which results into build errors.
Fix that by adding explicit handling of !defined(CONFIG_M5272) case.
Fixes: 80cca775cd ("net: fec: cache statistics while device is down")
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OPCODE_COMMON_GET_FN_PRIVILEGES is returning only DEVSEC
privilege (Unrestricted Administrative Privilege) for Lancer NIC functions.
So, driver is failing SET_HSW_CONFIG command, as DEVSEC privilege was not
set in the privilege bitmap. This patch fixes the problem by setting DEVSEC
privilege in SET_HSW_CONFIG’s privilege bitmap.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_VMAP_STACK=y, virtnet_set_mac_address() can be passed a
pointer to the stack and it will OOPS. Copy the address to the heap
to prevent the crash.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Laura Abbott <labbott@redhat.com>
Reported-by: zbyszek@in.waw.pl
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There have been some reports lately about TCP connection stalls caused
by NIC drivers that aren't setting gso_size on aggregated packets on rx
path. This causes TCP to assume that the MSS is actually the size of the
aggregated packet, which is invalid.
Although the proper fix is to be done at each driver, it's often hard
and cumbersome for one to debug, come to such root cause and report/fix
it.
This patch amends this situation in two ways. First, it adds a warning
on when this situation occurs, so it gives a hint to those trying to
debug this. It also limit the maximum probed MSS to the adverised MSS,
as it should never be any higher than that.
The result is that the connection may not have the best performance ever
but it shouldn't stall, and the admin will have a hint on what to look
for.
Tested with virtio by forcing gso_size to 0.
v2: updated msg per David's suggestion
v3: use skb_iif to find the interface and also log its name, per Eric
Dumazet's suggestion. As the skb may be backlogged and the interface
gone by then, we need to check if the number still has a meaning.
v4: use helper tcp_gro_dev_warn() and avoid pr_warn_once inside __once, per
David's suggestion
Cc: Jonathan Maxwell <jmaxwell37@gmail.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a wrong condition preventing the higher net device flags
IFF_LOWER_UP etc to be defined if net/if.h is included before
linux/if.h.
The comment makes it clear the intention was to allow partial
definition with either parts.
This fixes compilation of userspace programs trying to use
IFF_LOWER_UP, IFF_DORMANT or IFF_ECHO.
Fixes: 4a91cb61bb ("uapi glibc compat: fix compile errors when glibc net/if.h included before linux/if.h")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Reviewed-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
WR_OSR_LMT and RD_OSR_LMT have a reset value of 1.
Since the reset value wasn't cleared before writing, the value in the
register would be incorrect if specifying an uneven value for
snps,wr_osr_lmt/snps,rd_osr_lmt.
Zero is a valid value for the properties, since the databook specifies:
maximum outstanding requests = WR_OSR_LMT + 1.
We do not want to change the behavior for existing users when the
property is missing. Therefore, default to 1 if the property is missing,
since that is the same as the reset value.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basically, the pjdfstests set the ownership of a file to 06555, and then
chowns it (as root) to a new uid/gid. Prior to commit a09f99edde ("fuse:
fix killing s[ug]id in setattr"), fuse would send down a setattr with both
the uid/gid change and a new mode. Now, it just sends down the uid/gid
change.
Technically this is NOTABUG, since POSIX doesn't _require_ that we clear
these bits for a privileged process, but Linux (wisely) has done that and I
think we don't want to change that behavior here.
This is caused by the use of should_remove_suid(), which will always return
0 when the process has CAP_FSETID.
In fact we really don't need to be calling should_remove_suid() at all,
since we've already been indicated that we should remove the suid, we just
don't want to use a (very) stale mode for that.
This patch should fix the above as well as simplify the logic.
Reported-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: a09f99edde ("fuse: fix killing s[ug]id in setattr")
Cc: <stable@vger.kernel.org>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Since commit:
4bcc595ccd ("printk: reinstate KERN_CONT for printing continuation lines")
printk() requires KERN_CONT to continue log messages. Lots of printk()
in lockdep.c and print_ip_sym() don't have it. As the result lockdep
reports are completely messed up.
Add missing KERN_CONT and inline print_ip_sym() where necessary.
Example of a messed up report:
0-rc5+ #41 Not tainted
-------------------------------------------------------
syz-executor0/5036 is trying to acquire lock:
(
rtnl_mutex
){+.+.+.}
, at:
[<ffffffff86b3d6ac>] rtnl_lock+0x1c/0x20
but task is already holding lock:
(
&net->packet.sklist_lock
){+.+...}
, at:
[<ffffffff873541a6>] packet_diag_dump+0x1a6/0x1920
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3
(
&net->packet.sklist_lock
+.+...}
...
Without this patch all scripts that parse kernel bug reports are broken.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: andreyknvl@google.com
Cc: aryabinin@virtuozzo.com
Cc: joe@perches.com
Cc: syzkaller@googlegroups.com
Link: http://lkml.kernel.org/r/1480343083-48731-1-git-send-email-dvyukov@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The warning introduced in commit:
864c2357ca ("perf/core: Do not set cpuctx->cgrp for unscheduled cgroups")
assumed that a cgroup switch always precedes list_del_event. This is
not the case. Remove warning.
Make sure that cpuctx->cgrp is NULL until a cgroup event is sched in
or ctx->nr_cgroups == 0.
Signed-off-by: David Carrillo-Cisneros <davidcc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi V Shankar <ravi.v.shankar@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Vikas Shivappa <vikas.shivappa@linux.intel.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/1480841177-27299-1-git-send-email-davidcc@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Lukasz reported that perf stat counters overflow handling is broken on KNL/SLM.
Both these parts have full_width_write set, and that does indeed have
a problem. In order to deal with counter wrap, we must sample the
counter at at least half the counter period (see also the sampling
theorem) such that we can unambiguously reconstruct the count.
However commit:
069e0c3c40 ("perf/x86/intel: Support full width counting")
sets the sampling interval to the full period, not half.
Fixing that exposes another issue, in that we must not sign extend the
delta value when we shift it right; the counter cannot have
decremented after all.
With both these issues fixed, counter overflow functions correctly
again.
Reported-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Tested-by: Liang, Kan <kan.liang@intel.com>
Tested-by: Odzioba, Lukasz <lukasz.odzioba@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: stable@vger.kernel.org
Fixes: 069e0c3c40 ("perf/x86/intel: Support full width counting")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The Knights Mill is enough close to Knights Landing so the path reuses
C-state residency support of the latter.
Signed-off-by: Piotr Luc <piotr.luc@intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20161201000853.18260-1-piotr.luc@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For the "lea %(rsp), %rbp" case, we check if there is a rex_prefix.
But we check 'bytes' which is insn_byte_t[4] in rex_prefix (insn_field
structure). Therefore, the check is always true.
Instead, check 'nbytes' which is the right one.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20161205105551.25917-1-jslaby@suse.cz
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It is wrong to schedule a work from sk_destruct using the socket
as the memory reserve because the socket will be freed immediately
after the return from sk_destruct.
Instead we should do the deferral prior to sk_free.
This patch does just that.
Fixes: 707693c8a4 ("netlink: Call cb->done from a worker thread")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
