Currently NCSI driver will send several NCSI commands back to back without
waiting the response of previous NCSI command or timeout in some state
when NIC have multi channel. This operation against the single thread
manner defined by NCSI SPEC(section 6.3.2.3 in DSP0222_1.1.1)
According to NCSI SPEC(section 6.2.13.1 in DSP0222_1.1.1), we should probe
one channel at a time by sending NCSI commands (Clear initial state, Get
version ID, Get capabilities...), than repeat this steps until the max
number of channels which we got from NCSI command (Get capabilities) has
been probed.
Fixes: e6f44ed6d0 ("net/ncsi: Package and channel management")
Signed-off-by: DelphineCCChiu <delphine_cc_chiu@wiwynn.com>
Link: https://lore.kernel.org/r/20240529065856.825241-1-delphine_cc_chiu@wiwynn.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This change adds support for the NC-SI 1.2 Get MC MAC Address command,
specified here:
https://www.dmtf.org/sites/default/files/standards/documents/DSP0222_1.2.0.pdf
It serves the exact same function as the existing OEM Get MAC Address
commands, so if a channel reports that it supports NC-SI 1.2, we prefer
to use the standard command rather than the OEM command.
Verified with an invalid MAC address and 2 valid ones:
[ 55.137072] ftgmac100 1e690000.ftgmac eth0: NCSI: Received 3 provisioned MAC addresses
[ 55.137614] ftgmac100 1e690000.ftgmac eth0: NCSI: MAC address 0: 00:00:00:00:00:00
[ 55.138026] ftgmac100 1e690000.ftgmac eth0: NCSI: MAC address 1: fa:ce:b0:0c:20:22
[ 55.138528] ftgmac100 1e690000.ftgmac eth0: NCSI: MAC address 2: fa:ce:b0:0c:20:23
[ 55.139241] ftgmac100 1e690000.ftgmac eth0: NCSI: Unable to assign 00:00:00:00:00:00 to device
[ 55.140098] ftgmac100 1e690000.ftgmac eth0: NCSI: Set MAC address to fa:ce:b0:0c:20:22
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Signed-off-by: Patrick Williams <patrick@stwcx.xyz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netlink interface for major and minor version numbers doesn't actually
return the major and minor version numbers.
It reports a u32 that contains the (major, minor, update, alpha1)
components as the major version number, and then alpha2 as the minor
version number.
For whatever reason, the u32 byte order was reversed (ntohl): maybe it was
assumed that the encoded value was a single big-endian u32, and alpha2 was
the minor version.
The correct way to get the supported NC-SI version from the network
controller is to parse the Get Version ID response as described in 8.4.44
of the NC-SI spec[1].
Get Version ID Response Packet Format
Bits
+--------+--------+--------+--------+
Bytes | 31..24 | 23..16 | 15..8 | 7..0 |
+-------+--------+--------+--------+--------+
| 0..15 | NC-SI Header |
+-------+--------+--------+--------+--------+
| 16..19| Response code | Reason code |
+-------+--------+--------+--------+--------+
|20..23 | Major | Minor | Update | Alpha1 |
+-------+--------+--------+--------+--------+
|24..27 | reserved | Alpha2 |
+-------+--------+--------+--------+--------+
| .... other stuff .... |
The major, minor, and update fields are all binary-coded decimal (BCD)
encoded [2]. The spec provides examples below the Get Version ID response
format in section 8.4.44.1, but for practical purposes, this is an example
from a live network card:
root@bmc:~# ncsi-util 0x15
NC-SI Command Response:
cmd: GET_VERSION_ID(0x15)
Response: COMMAND_COMPLETED(0x0000) Reason: NO_ERROR(0x0000)
Payload length = 40
20: 0xf1 0xf1 0xf0 0x00 <<<<<<<<< (major, minor, update, alpha1)
24: 0x00 0x00 0x00 0x00 <<<<<<<<< (_, _, _, alpha2)
28: 0x6d 0x6c 0x78 0x30
32: 0x2e 0x31 0x00 0x00
36: 0x00 0x00 0x00 0x00
40: 0x16 0x1d 0x07 0xd2
44: 0x10 0x1d 0x15 0xb3
48: 0x00 0x17 0x15 0xb3
52: 0x00 0x00 0x81 0x19
This should be parsed as "1.1.0".
"f" in the upper-nibble means to ignore it, contributing zero.
If both nibbles are "f", I think the whole field is supposed to be ignored.
Major and minor are "required", meaning they're not supposed to be "ff",
but the update field is "optional" so I think it can be ff. I think the
simplest thing to do is just set the major and minor to zero instead of
juggling some conditional logic or something.
bcd2bin() from "include/linux/bcd.h" seems to assume both nibbles are 0-9,
so I've provided a custom BCD decoding function.
Alpha1 and alpha2 are ISO/IEC 8859-1 encoded, which just means ASCII
characters as far as I can tell, although the full encoding table for
non-alphabetic characters is slightly different (I think).
I imagine the alpha fields are just supposed to be alphabetic characters,
but I haven't seen any network cards actually report a non-zero value for
either.
If people wrote software against this netlink behavior, and were parsing
the major and minor versions themselves from the u32, then this would
definitely break their code.
[1] https://www.dmtf.org/sites/default/files/standards/documents/DSP0222_1.0.0.pdf
[2] https://en.wikipedia.org/wiki/Binary-coded_decimal
[2] https://en.wikipedia.org/wiki/ISO/IEC_8859-1
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Fixes: 138635cc27 ("net/ncsi: NCSI response packet handler")
Signed-off-by: David S. Miller <davem@davemloft.net>
Background:
1. CONFIG_NCSI_OEM_CMD_KEEP_PHY
If this is enabled, we send an extra OEM Intel command in the probe
sequence immediately after discovering a channel (e.g. after "Clear
Initial State").
2. CONFIG_NCSI_OEM_CMD_GET_MAC
If this is enabled, we send one of 3 OEM "Get MAC Address" commands from
Broadcom, Mellanox (Nvidida), and Intel in the *configuration* sequence
for a channel.
3. mellanox,multi-host (or mlx,multi-host)
Introduced by this patch:
https://lore.kernel.org/all/20200108234341.2590674-1-vijaykhemka@fb.com/
Which was actually originally from cosmo.chou@quantatw.com:
9f132a10ec
Cosmo claimed that the Nvidia ConnectX-4 and ConnectX-6 NIC's don't
respond to Get Version ID, et. al in the probe sequence unless you send
the Set MC Affinity command first.
Problem Statement:
We've been using a combination of #ifdef code blocks and IS_ENABLED()
conditions to conditionally send these OEM commands.
It makes adding any new code around these commands hard to understand.
Solution:
In this patch, I just want to remove the conditionally compiled blocks
of code, and always use IS_ENABLED(...) to do dynamic control flow.
I don't think the small amount of code this adds to non-users of the OEM
Kconfigs is a big deal.
Signed-off-by: Peter Delevoryas <peter@pjd.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3780bb2931.
The cited commit introduced unwanted behavior.
The intent for the commit was to be able to detect carrier loss/gain
for just the NIC connected to the BMC. The unwanted effect is a
carrier loss for auxiliary paths also causes the BMC to lose
carrier. The BMC never regains carrier despite the secondary NIC
regaining a link.
This change, when merged, needs to be backported to stable kernels.
5.4-stable, 5.10-stable, 5.15-stable, 6.1-stable, 6.5-stable
Fixes: 3780bb2931 ("ncsi: Propagate carrier gain/loss events to the NCSI controller")
CC: stable@vger.kernel.org
Signed-off-by: Johnathan Mantey <johnathanx.mantey@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the carrier/no-carrier state for the network interface
shared between the BMC and the passthrough channel. Without this
functionality the BMC is unable to reconfigure the NIC in the event
of a re-cabling to a different subnet.
Signed-off-by: Johnathan Mantey <johnathanx.mantey@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct netlink_callback has a const nlh pointer, make the
pointer in struct genl_info const as well, to make copying
between the two easier.
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://lore.kernel.org/r/20230814214723.2924989-3-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Change ndo_set_mac_address to dev_set_mac_address because
dev_set_mac_address provides a way to notify network layer about MAC
change. In other case, services may not aware about MAC change and keep
using old one which set from network adapter driver.
As example, DHCP client from systemd do not update MAC address without
notification from net subsystem which leads to the problem with acquiring
the right address from DHCP server.
Fixes: cb10c7c0df ("net/ncsi: Add NCSI Broadcom OEM command")
Cc: stable@vger.kernel.org # v6.0+ 2f38e84 net/ncsi: make one oem_gma function for all mfr id
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the one Get Mac Address function for all manufacturers and change
this call in handlers accordingly.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Ivan Mikhaylov <fr0st61te@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ncsi_channel_is_tx() determines whether a given channel should be
used for Tx or not. However, when reconfiguring the channel by
handling a Configuration Required AEN, there is a misjudgment that
the channel Tx has already been enabled, which results in the Enable
Channel Network Tx command not being sent.
Clear the channel Tx enable flag before reconfiguring the channel to
avoid the misjudgment.
Fixes: 8d951a75d0 ("net/ncsi: Configure multi-package, multi-channel modes with failover")
Signed-off-by: Cosmo Chou <chou.cosmo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties.
Convert reading boolean properties to of_property_read_bool().
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for net/can
Acked-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memcpy() in ncsi_cmd_handler_oem deserializes nca->data into a
flexible array structure that overlapping with non-flex-array members
(mfr_id) intentionally. Since the mem_to_flex() API is not finished,
temporarily silence this warning, since it is a false positive, using
unsafe_memcpy().
Reported-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/netdev/CACPK8Xdfi=OJKP0x0D1w87fQeFZ4A2DP2qzGCRcuVbpU-9=4sQ@mail.gmail.com/
Cc: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20221202212418.never.837-kees@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We had historically not checked that genlmsghdr.reserved
is 0 on input which prevents us from using those precious
bytes in the future.
One use case would be to extend the cmd field, which is
currently just 8 bits wide and 256 is not a lot of commands
for some core families.
To make sure that new families do the right thing by default
put the onus of opting out of validation on existing families.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Paul Moore <paul@paul-moore.com> (NetLabel)
Signed-off-by: David S. Miller <davem@davemloft.net>
find_first{,_zero}_bit is a more effective analogue of 'next' version if
start == 0. This patch replaces 'next' with 'first' where things look
trivial.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
As we can see from the comment of the nla_put() that it could return
-EMSGSIZE if the tailroom of the skb is insufficient.
Therefore, it should be better to check the return value of the
nla_put_u32 and return the error code if error accurs.
Also, there are many other functions have the same problem, and if this
patch is correct, I will commit a new version to fix all.
Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20211229032118.1706294-1-jiasheng@iscas.ac.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Update NC-SI command handler (both standard and OEM) to take into
account of payload paddings in allocating skb (in case of payload
size is not 32-bit aligned).
The checksum field follows payload field, without taking payload
padding into account can cause checksum being truncated, leading to
dropped packets.
Fixes: fb4ee67529 ("net/ncsi: Add NCSI OEM command support")
Signed-off-by: Kumar Thangavel <thangavel.k@hcl.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds OEM Intel GMA command and response handler for it.
Signed-off-by: Brad Ho <Brad_Ho@phoenix.com>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Link: https://lore.kernel.org/r/20210830171806.119857-2-i.mikhaylov@yadro.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the dummy response handler for Intel boards to prevent incorrect
handling of OEM commands.
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows to keep PHY link up and prevents any channel resets during
the host load.
It is KEEP_PHY_LINK_UP option(Veto bit) in i210 datasheet which
block PHY reset and power state changes.
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse reports:
net/ncsi/ncsi-rsp.c:406:24: warning: cast to restricted __be32
net/ncsi/ncsi-manage.c:732:33: warning: cast to restricted __be32
net/ncsi/ncsi-manage.c:756:25: warning: cast to restricted __be32
net/ncsi/ncsi-manage.c:779:25: warning: cast to restricted __be32
Signed-off-by: Ivan Mikhaylov <i.mikhaylov@yadro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix some spelling mistakes in comments:
constuct ==> construct
chanels ==> channels
Detination ==> Destination
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Calling ncsi_stop_channel_monitor from channel_monitor is a guaranteed
deadlock on SMP because stop calls del_timer_sync on the timer that
invoked channel_monitor as its timer function.
Recognise the inherent race of marking the monitor disabled before
deleting the timer by just returning if enable was cleared. After
a timeout (the default case -- reset to START when response received)
just mark the monitor.enabled false.
If the channel has an entry on the channel_queue list, or if the
state is not ACTIVE or INACTIVE, then warn and mark the timer stopped
and don't restart, as the locking is broken somehow.
Fixes: 0795fb2021 ("net/ncsi: Stop monitor if channel times out or is inactive")
Signed-off-by: Milton Miller <miltonm@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When aggregating ncsi interfaces and dedicated interfaces to bond
interfaces, the ncsi response handler will use the wrong net device to
find ncsi_dev, so that the ncsi interface will not work properly.
Here, we use the original net device to fix it.
Fixes: 138635cc27 ("net/ncsi: NCSI response packet handler")
Signed-off-by: John Wang <wangzhiqiang.bj@bytedance.com>
Link: https://lore.kernel.org/r/20201223055523.2069-1-wangzhiqiang.bj@bytedance.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a user unbinds and re-binds a NC-SI aware driver the kernel will
attempt to register the netlink interface at runtime. The structure is
marked __ro_after_init so registration fails spectacularly at this point.
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/unbind
# echo 1e660000.ethernet > /sys/bus/platform/drivers/ftgmac100/bind
ftgmac100 1e660000.ethernet: Read MAC address 52:54:00:12:34:56 from chip
ftgmac100 1e660000.ethernet: Using NCSI interface
8<--- cut here ---
Unable to handle kernel paging request at virtual address 80a8f858
pgd = 8c768dd6
[80a8f858] *pgd=80a0841e(bad)
Internal error: Oops: 80d [#1] SMP ARM
CPU: 0 PID: 116 Comm: sh Not tainted 5.10.0-rc3-next-20201111-00003-gdd25b227ec1e #51
Hardware name: Generic DT based system
PC is at genl_register_family+0x1f8/0x6d4
LR is at 0xff26ffff
pc : [<8073f930>] lr : [<ff26ffff>] psr: 20000153
sp : 8553bc80 ip : 81406244 fp : 8553bd04
r10: 8085d12c r9 : 80a8f73c r8 : 85739000
r7 : 00000017 r6 : 80a8f860 r5 : 80c8ab98 r4 : 80a8f858
r3 : 00000000 r2 : 00000000 r1 : 81406130 r0 : 00000017
Flags: nzCv IRQs on FIQs off Mode SVC_32 ISA ARM Segment none
Control: 00c5387d Table: 85524008 DAC: 00000051
Process sh (pid: 116, stack limit = 0x1f1988d6)
...
Backtrace:
[<8073f738>] (genl_register_family) from [<80860ac0>] (ncsi_init_netlink+0x20/0x48)
r10:8085d12c r9:80c8fb0c r8:85739000 r7:00000000 r6:81218000 r5:85739000
r4:8121c000
[<80860aa0>] (ncsi_init_netlink) from [<8085d740>] (ncsi_register_dev+0x1b0/0x210)
r5:8121c400 r4:8121c000
[<8085d590>] (ncsi_register_dev) from [<805a8060>] (ftgmac100_probe+0x6e0/0x778)
r10:00000004 r9:80950228 r8:8115bc10 r7:8115ab00 r6:9eae2c24 r5:813b6f88
r4:85739000
[<805a7980>] (ftgmac100_probe) from [<805355ec>] (platform_drv_probe+0x58/0xa8)
r9:80c76bb0 r8:00000000 r7:80cd4974 r6:80c76bb0 r5:8115bc10 r4:00000000
[<80535594>] (platform_drv_probe) from [<80532d58>] (really_probe+0x204/0x514)
r7:80cd4974 r6:00000000 r5:80cd4868 r4:8115bc10
Jakub pointed out that ncsi_register_dev is obviously broken, because
there is only one family so it would never work if there was more than
one ncsi netdev.
Fix the crash by registering the netlink family once on boot, and drop
the code to unregister it.
Fixes: 955dc68cb9 ("net/ncsi: Add generic netlink family")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Link: https://lore.kernel.org/r/20201112061210.914621-1-joel@jms.id.au
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Bulk of the genetlink users can use smaller ops, move them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_zero_addr() to clear mac address insetad of memset().
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Multi host Mellanox cards require MAC affinity to be set
before receiving any config commands. All config commands
should also have unicast address for source address in
command header.
Adding GMA and SMAF(Set Mac Affinity) for Mellanox card
and call these in channel probe state machine if it is
defined in device tree.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After receiving device mac address from device, send this as
a source address for further commands instead of broadcast
address.
This will help in multi host NIC cards.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gma_flag was set at the time of GMA command request but it should
only be set after getting successful response. Movinng this flag
setting in GMA response handler.
This flag is used mainly for not repeating GMA command once
received MAC address.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Reviewed-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling multicast filtering from NCSI if it is supported. As it
should not filter any multicast packets. In current code, multicast
filter is enabled and with an exception of optional field supported
by device are disabled filtering.
Mainly I see if goal is to disable filtering for IPV6 packets then let
it disabled for every other types as well. As we are seeing issues with
LLDP not working with this enabled filtering. And there are other issues
with IPV6.
By Disabling this multicast completely, it is working for both IPV6 as
well as LLDP.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
This patch adds handlers for PLDM over NC-SI command response.
This enables NC-SI driver recognizes the packet type so the responses
don't get dropped as unknown packet type.
PLDM over NC-SI are not handled in kernel driver for now, but can be
passed back to user space via Netlink for further handling.
Signed-off-by: Ben Wei <benwei@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update response packet length for the following commands per NC-SI spec
- Get Controller Packet Statistics
- Get NC-SI Statistics
- Get NC-SI Pass-through Statistics command
Signed-off-by: Ben Wei <benwei@fb.com>
Reviewed-by: Justin Lee <justin.lee1@dell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The request coming from Netlink should use the OEM generic handler.
The standard command handler expects payload in bytes/words/dwords
but the actual payload is stored in data if the request is coming from Netlink.
Signed-off-by: Justin Lee <justin.lee1@dell.com>
Reviewed-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NCSI spec indicates that if the data does not end on a 32 bit
boundary, one to three padding bytes equal to 0x00 shall be present to
align the checksum field to a 32-bit boundary.
Signed-off-by: Terry S. Duncan <terry.s.duncan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.
Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:
@@
identifier ops;
expression X;
@@
struct genl_ops ops[] = {
...,
{
.cmd = X,
+ .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
...
},
...
};
For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously BMC's MAC address is calculated by simply adding 1 to the
last byte of network controller's MAC address, and it produces incorrect
result when network controller's MAC address ends with 0xFF.
The problem can be fixed by calling eth_addr_inc() function to increment
MAC address; besides, the MAC address is also validated before assigning
to BMC.
Fixes: cb10c7c0df ("net/ncsi: Add NCSI Broadcom OEM command")
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since maxattr is common, the policy can't really differ sanely,
so make it common as well.
The only user that did in fact manage to make a non-common policy
is taskstats, which has to be really careful about it (since it's
still using a common maxattr!). This is no longer supported, but
we can fake it using pre_doit.
This reduces the size of e.g. nl80211.o (which has lots of commands):
text data bss dec hex filename
398745 14323 2240 415308 6564c net/wireless/nl80211.o (before)
397913 14331 2240 414484 65314 net/wireless/nl80211.o (after)
--------------------------------
-832 +8 0 -824
Which is obviously just 8 bytes for each command, and an added 8
bytes for the new policy pointer. I'm not sure why the ops list is
counted as .text though.
Most of the code transformations were done using the following spatch:
@ops@
identifier OPS;
expression POLICY;
@@
struct genl_ops OPS[] = {
...,
{
- .policy = POLICY,
},
...
};
@@
identifier ops.OPS;
expression ops.POLICY;
identifier fam;
expression M;
@@
struct genl_family fam = {
.ops = OPS,
.maxattr = M,
+ .policy = POLICY,
...
};
This also gets rid of devlink_nl_cmd_region_read_dumpit() accessing
the cb->data as ops, which we want to change in a later genl patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nla_nest_start may fail and thus deserves a check.
The fix returns -EMSGSIZE in case it fails.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds OEM Mellanox commands and response handling. It also
defines OEM Get MAC Address handler to get and configure the device.
ncsi_oem_gma_handler_mlx: This handler send NCSI mellanox command for
getting mac address.
ncsi_rsp_handler_oem_mlx: This handles response received for all
mellanox OEM commands.
ncsi_rsp_handler_oem_mlx_gma: This handles get mac address response and
set it to device.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
