Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Note with a comment anything newer than DP 1.1a.
Obviously this needs some work still...
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sources: DP, eDP, and DP interop specs, and a VESA slideshow about DP
1.2 for the MST bits.
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Adam Jackson <ajax@redhat.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Low four bits are downstream port count. High bit indicates peer OUI
support. OUI matching will allow us to do additional per-sink handling
for things like DP->VGA bandwidth limits or (hopefully) the iMac-as-
display hack.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DisplayPort has an escape hatch by which sources and sinks can identify
each other. We would prefer not to notice this, but I suspect we're
going to need to.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should make eDP more reliable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
DPCD 1.1+ adds some automated test infrastructure support. Add support
for reading the IRQ source and jumping to a test handling routine if
needed. Subsequent patches will handle particular tests; this patch
just ACKs any requested tests by default.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Add the addresses and definitions I care about for Panel Self Refresh, as
documented in the eDP spec.
I'm sending these out before some other patches because this should be a fairly
simple one to get upstream and not require too much fuss (where the others may
have some fuss).
This file is a mess with white spacing. I tried to stay consistent with the
surrounding code.
v2: had some silly mistakes in v1 which Keith caught
Cc: Dave Airlie <airlied@redhat.com>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Keith Packard <keithp@keithp.com>
We need to use some of these values in eDP configurations, so be sure to
fetch them and store them in the i915 private structure.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
- dpcp -> dpcd
- fix up dig encoder routing
- aux transaction table takes delay in 10 usec units
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Both radeon and nouveau can re-use this code so move it up a level
so they can. However the hw interfaces for aux ch are different
enough that the code to translate from mode, address, bytes
to actual hw interfaces isn't generic, so move that code into the
Intel driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
