DCE5 and newer hardware only has 1 DAC. Use the correct
offset. This may fix display problems on certain board
configurations.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
pci config reset is a low level reset that resets
the entire chip from the bus interface. It can
be more reliable if soft reset fails.
v2: put behind module parameter
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fill in asic family specific versions rather than
using the generic version. This lets us handle asic
specific differences more easily. In this case, we
disable sw swapping of the rtpr writeback value on
r6xx+ since the hw does it for us. Fixes bogus
rptr readback on BE systems.
v2: remove missed cpu_to_le32(), add comments
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need more control over the ordering of dpm init with
respect to the rest of the asic. Specifically, the SMC
has to be initialized before the rlc and cg/pg. The pm
code currently initializes late in the driver, but we need
it to happen much earlier so move pm handling into the asic
specific callbacks.
This makes dpm more reliable and makes clockgating work
properly on CIK parts and should help on SI parts as well.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to reorder the driver init sequence to better accomodate
dpm which needs to be loaded earlier in the init sequence. Move
fw init up so that it's available for dpm init.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull drm updates from Dave Airlie:
"This is a combo of -next and some -fixes that came in in the
intervening time.
Highlights:
New drivers:
ARM Armada driver for Marvell Armada 510 SOCs
Intel:
Broadwell initial support under a default off switch,
Stereo/3D HDMI mode support
Valleyview improvements
Displayport improvements
Haswell fixes
initial mipi dsi panel support
CRC support for debugging
build with CONFIG_FB=n
Radeon:
enable DPM on a number of GPUs by default
secondary GPU powerdown support
enable HDMI audio by default
Hawaii support
Nouveau:
dynamic pm code infrastructure reworked, does nothing major yet
GK208 modesetting support
MSI fixes, on by default again
PMPEG improvements
pageflipping fixes
GMA500:
minnowboard SDVO support
VMware:
misc fixes
MSM:
prime, plane and rendernodes support
Tegra:
rearchitected to put the drm driver into the drm subsystem.
HDMI and gr2d support for tegra 114 SoC
QXL:
oops fix, and multi-head fixes
DRM core:
sysfs lifetime fixes
client capability ioctl
further cleanups to device midlayer
more vblank timestamp fixes"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (789 commits)
drm/nouveau: do not map evicted vram buffers in nouveau_bo_vma_add
drm/nvc0-/gr: shift wrapping bug in nvc0_grctx_generate_r406800
drm/nouveau/pwr: fix missing mutex unlock in a failure path
drm/nv40/therm: fix slowing down fan when pstate undefined
drm/nv11-: synchronise flips to vblank, unless async flip requested
drm/nvc0-: remove nasty fifo swmthd hack for flip completion method
drm/nv10-: we no longer need to create nvsw object on user channels
drm/nouveau: always queue flips relative to kernel channel activity
drm/nouveau: there is no need to reserve/fence the new fb when flipping
drm/nouveau: when bailing out of a pushbuf ioctl, do not remove previous fence
drm/nouveau: allow nouveau_fence_ref() to be a noop
drm/nvc8/mc: msi rearm is via the nvc0 method
drm/ttm: Fix vma page_prot bit manipulation
drm/vmwgfx: Fix a couple of compile / sparse warnings and errors
drm/vmwgfx: Resource evict fixes
drm/edid: compare actual vrefresh for all modes for quirks
drm: shmob_drm: Convert to clk_prepare/unprepare
drm/nouveau: fix 32-bit build
drm/i915/opregion: fix build error on CONFIG_ACPI=n
Revert "drm/radeon/audio: don't set speaker allocation on DCE4+"
...
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
The buffers needs to be in little endian format.
Noticed-by: Sylvain BERTRAND <sylware@legeek.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allows you to enable dither in the display hardware
when the monitor supports lower a lower bpc than the
current framebuffer format.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The FMT blocks control how data is sent from the backend
of the display pipe to to monitor. Proper set up of the
FMT blocks are required for 30bpp formats. Additionally,
dithering can be enabled on for better display with 18 and
24bpp displays. The exception is LVDS/eDP which atom
takes care of in the SelectCRTC_Source table. For now
just enable truncation until we test dithering more.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use pcie_get_readrq() and pcie_set_readrq() functions to simplify code.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
The vram scratch buffer needs to be initialized
before the mc is programmed otherwise we program
0 as the GPU address of the default GPU fault
page. In most cases we put vram at zero anyway and
reserve a page for the legacy vga buffer so in practice
this shouldn't cause any problems, but better to make
it correct.
Was changed in:
6fab3febf6
Reported-by: FrankR Huang <FrankR.Huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We need to allocate line buffer to each display when
setting up the watermarks. Failure to do so can lead
to a blank screen. This fixes blank screen problems
on dce4.1/5 asics.
Based on an initial fix from:
Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The format of the clearstate buffer used for pg (powergating)
changed between NI and SI. This formats it properly for what
the hardware expects on SI+.
v2: fix addresses
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The format of the clearstate buffer used for pg (powergating)
changed between NI and SI. This formats it properly for what
the hardware expects on SI.
v2: fix addresses
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Similar to separating the UVD code, just put the DMA
functions into separate files.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our different hardware blocks are actually completely
separated, so it doesn't make much sense any more to
structure the code by pure chipset generations.
Start restructuring the code by separating our the UVD block.
v2: updated commit message
v3: rebased and restructurized start/stop functions for kv dpm.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that we have callbacks for [rw]ptr handling we can
remove the special handling for the DMA rings and use
the callbacks instead.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hardware just doesn't support this correctly.
Disable it before we accidentally write anywhere we shouldn't.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we PG (powergate) UVD, we need to re-initialize it
before we can use it again.
v2: rebase on UVD stop fixes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For r6xx+ asics. This mirrors the behavior of pre-r6xx
asics. We need to program the MC even if something
else in startup() fails. Failure to do so results in
an unusable GPU.
Based on a fix from: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Removing the clock/power or resetting the VCPU can cause
hangs if that happens in the middle of a register write.
Stall the memory and register bus before putting the VCPU
into reset. Keep it in reset when unloading the module or
suspending.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Last driver and pretty obviously a major user of this little function.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Helpful for debugging GPUVM errors as we can see what
hw block and page generated the fault in the log.
v2: simplify fault decoding
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Fix patching of vddc values for SI and enable manually forcing
clocks to default levels as per NI.
This improves the out of the box performance with SI asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for trinity asics. This includes:
- clockgating
- powergating
- dynamic engine clock scaling
- dynamic voltage scaling
set radeon.dpm=1 to enable it.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calculate the low and high watermarks based on the low and high
clocks for the current power state. The dynamic pm hw will select
the appropriate watermark based on the internal dpm state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is required for certain advanced functionality.
v2: save/restore list takes dword offsets
v3: rebase on gpu reset changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The current radeon driver initialization routines, when using KMS, are written
so that the IRQ installation routine is called before initializing the WB buffer
and the CP rings. With some ASICs, though, the IRQ routine tries to access the
GFX_INDEX ring causing a call to RREG32 with the value of -1 in
radeon_fence_read. This, in turn causes the system to completely hang with some
cards, requiring a hard reset.
A call stack that can cause such a hang looks like this (using rv515 ASIC for the
example here):
* rv515_init (rv515.c)
* radeon_irq_kms_init (radeon_irq_kms.c)
* drm_irq_install (drm_irq.c)
* radeon_driver_irq_preinstall_kms (radeon_irq_kms.c)
* rs600_irq_process (rs600.c)
* radeon_fence_process - due to SW interrupt (radeon_fence.c)
* radeon_fence_read (radeon_fence.c)
* hang due to RREG32(-1)
The patch moves the IRQ installation to the card startup routine, after the ring
has been initialized, but before the IRQ has been set. This fixes the issue, but
requires a check to see if the IRQ is already installed, as is the case in the
system resume codepath.
I have tested the patch on three machines using the rv515, the rv770 and the
evergreen ASIC. They worked without issues.
This seems to be a known issue and has been reported on several bug tracking
sites by various distributions (see links below). Most of reports recommend
booting the system with KMS disabled and then enabling KMS by reloading the
radeon module. For some reason, this was indeed a usable workaround, however,
UMS is now deprecated and disabled by default.
Bug reports:
https://bugzilla.redhat.com/show_bug.cgi?id=845745https://bugs.launchpad.net/ubuntu/+source/linux/+bug/561789https://bbs.archlinux.org/viewtopic.php?id=156964
Signed-off-by: Adis Hamzić <adis@hamzadis.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
radeon currently uses a drm function to get the speed capabilities for
the bus, drm_pcie_get_speed_cap_mask. However, this is a non-standard
method of performing this detection and this patch changes it to use
the max_bus_speed attribute.
From: Lucas Kannebley Tavares <lucaskt@linux.vnet.ibm.com>
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hainan has no display hardware:
- no DCE (crtc, uniphy, dac, etc.)
- no VGA
v2: fix bios fetch
v3: fix interrupts
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Instead of duplicating the code over and over again, just use a single
function to handle the clock calculations.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Just power down the PLL when we get a VCLK or DCLK of zero.
Enabling the bypass mode early should also allow us to
switch UVD clocks on the fly.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
