If more than 127 different lengths are transmitted then the driver causes
an overrun on sample_lens. Try to send as much as possible and return the
amount sent.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This transceiver expects the set IR TX ports and IR data as seperate
packets, like the Windows driver does. Remove unnecessary kzalloc.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The GET_REVISION command puts the device in an unresponsive state,
although it continues to report any IR activity. Note that GET_REVISION
command is not documented, nor is any possible response to it parsed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On cold boot the device does not initialize until the first packet is
received, and that packet is not processed.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A sample resolution of 2us generates more than 300 interrupts per key
and this resolution is not needed unless carrier reports are enabled.
Revert to a resolution of 10us unless carrier reports are needed. This
generates up to a fifth of the interrupts.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Events for the iMon Knob pad where not correctly interpreted on ARM,
resulting in buggy mouse movements (cursor going straight out of the
screen), key pad only generating KEY_RIGHT and KEY_DOWN events.
A reproducer is:
int main(int argc, char ** argv)
{
char rel_x = 0x00; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
rel_x = 0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
rel_x |= ~0x0f; printf("rel_x:%d @%s:%d\n", rel_x, __FILE__, __LINE__);
return 0;
}
(running on x86 or amd64)
$ ./test
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:-1 @test.c:8
(running on armv6)
rel_x:0 @test.c:6
rel_x:15 @test.c:7
rel_x:255 @test.c:8
Forcing the rel_x and rel_y variables as signed char fixes the issue.
Reference: http://www.arm.linux.org.uk/docs/faqs/signedchar.php
Signed-off-by: Alexandre Lissy <alexandrelissy@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* v4l_for_linus: (464 commits)
[media] uvcvideo: Set error_idx properly for S_EXT_CTRLS failures
[media] uvcvideo: Cleanup leftovers of partial revert
[media] uvcvideo: Return -EACCES when trying to set a read-only control
Linux 3.8-rc3
mm: reinstante dropped pmd_trans_splitting() check
cred: Remove tgcred pointer from struct cred
drm/ttm: fix fence locking in ttm_buffer_object_transfer
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
drm/prime: drop reference on imported dma-buf come from gem
xen/netfront: improve truesize tracking
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
sctp: fix Kconfig bug in default cookie hmac selection
EDAC: Cleanup device deregistering path
...
Conflicts:
drivers/media/pci/dm1105/dm1105.c
drivers/media/platform/soc_camera/mx2_camera.c
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During modiles initialization rc-core schedules work which calls
request_module() several times to load ir-*-decoder modules, but
it does not wait or cancel this work on module unloading.
rc-core should use request_module_nowait() instead, because it
anyway cannot load modules synchronously or cancel/wait pending
work on unloading, because this leads to deadlock on modules_mutex
between several "modprobe" processes.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This error path is missing the unlock.
[mchehab@redhat.com: Merged two equal patches into one]
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJQ1QqgAAoJEHm+PkMAQRiG3GMIAJZjN2+0EGFpcq0LDrjIMyLG
PFuCkn9wNybAVR38DuVJkYclLclN2T1CevWZib+GgRLZO2IU5Qu1xh+fCLRn1u5i
qrxq8g4HYVMYXDixdZzXA2eXCLF7YLzPEdlowoBItGl9OJjQdzk3zBATtJGxfKaP
zvmaXP0CyoQekrZmmpMEl2/PLY/X0Ett6I5tlKcTvYKbbowG1SoAwVEVokCZC/vi
I+y8/8M68eDfOfYZ8BoRd5Lsygxfw8uvOce4qUeKawiZPO8bWP1s9NFyK6Ank6+s
hNXM9dNm6l0JfS+Ykb2FXleuEmOaaloRswOxukU1gKC3V0HdxwKx0Ir4P3z1dHM=
=5Iln
-----END PGP SIGNATURE-----
Merge tag 'v3.8-rc1' into staging/for_v3.9
Linux 3.8-rc1
* tag 'v3.8-rc1': (10696 commits)
Linux 3.8-rc1
Revert "nfsd: warn on odd reply state in nfsd_vfs_read"
ARM: dts: fix duplicated build target and alphabetical sort out for exynos
dm stripe: add WRITE SAME support
dm: remove map_info
dm snapshot: do not use map_context
dm thin: dont use map_context
dm raid1: dont use map_context
dm flakey: dont use map_context
dm raid1: rename read_record to bio_record
dm: move target request nr to dm_target_io
dm snapshot: use per_bio_data
dm verity: use per_bio_data
dm raid1: use per_bio_data
dm: introduce per_bio_data
dm kcopyd: add WRITE SAME support to dm_kcopyd_zero
dm linear: add WRITE SAME support
dm: add WRITE SAME support
dm: prepare to support WRITE SAME
dm ioctl: use kmalloc if possible
...
Conflicts:
MAINTAINERS
We recently introduced a new return -ENODEV in this function but we need
to unlock before returning.
[mchehab@redhat.com: found two patches with the same fix. Merged SOB's/acks into one patch]
Acked-by: Herton R. Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Douglas Bagnall <douglas@paradise.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This should fix a potential race condition, when the irq handler
triggers while rc_register_device is still setting up the rdev->raw
device.
This crash has not been observed in practice, but there should be a very
small window where it could occur. Since ir_raw_event_store_with_filter
checks if rdev->raw is not NULL before using it, this bug is not
triggered if the request_irq triggers a pending irq directly (since
rdev->raw will still be NULL then).
This commit was tested on nuvoton-cir only.
Cc: Jarod Wilson <jarod@redhat.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This fixes a problem in fintek-cir and nuvoton-cir where the
irq handler would trigger during module load before the rdev member was
set, causing a NULL pointer crash.
It seems this crash is very reproducible (just bombard the receiver with
IR signals during module load), probably because when request_irq is
called, any pending intterupt is handled immediately, before
request_irq returns and rdev can be set.
This same crash was supposed to be fixed by commit
9ef449c6b3 ("[media] rc: Postpone ISR
registration"), but the crash was still observed on the nuvoton-cir
driver.
This commit was tested on nuvoton-cir only.
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before, labels were simply numbered. Now, the labels are named after the
cleanup action they'll perform (first), based on how the winbond-cir
driver does it. This makes the code a bit more clear and makes changes
in the ordering of labels easier to review.
This change is applied only to the rc drivers that do significant
cleanup in their probe functions: ati-remote, ene-ir, fintek-cir,
gpio-ir-recv, ite-cir, nuvoton-cir.
This commit should not change any code, it just renames goto labels.
[mchehab@redhat.com: removed changes at gpio-ir-recv.c, due to
merge conflicts]
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since rc_unregister_device() frees its argument there's no need to
subsequently call rc_free_device() on the same variable - in fact it's
a double free bug.
Easily fixed by just removing the rc_free_device() call.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
At the 'err_request_irq' label, rc_unregister_device(rcdev) frees its
argument. So when we fall through to the 'err_gpio_request' label
further down and call rc_free_device(rcdev) then that's a double free.
Fix that by moving 'rcdev = NULL' from after the call to
rc_free_device() to after rc_unregister_device(). That fixes the
problem since rc_free_device() just does nothing if passed NULL and
there's no further use of 'rcdev' after the call to rc_free_device()
so it's not needed there.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull media updates from Mauro Carvalho Chehab:
- Missing MAINTAINERS entries were added for several drivers
- Adds V4L2 support for DMABUF handling, allowing zero-copy buffer
sharing between V4L2 devices and GPU
- Got rid of all warnings when compiling with W=1 on x86
- Add a new driver for Exynos hardware (s3c-camif)
- Several bug fixes, cleanups and driver improvements
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (243 commits)
[media] omap3isp: Replace cpu_is_omap3630() with ISP revision check
[media] omap3isp: Prepare/unprepare clocks before/after enable/disable
[media] omap3isp: preview: Add support for 8-bit formats at the sink pad
[media] omap3isp: Replace printk with dev_*
[media] omap3isp: Find source pad from external entity
[media] omap3isp: Configure CSI-2 phy based on platform data
[media] omap3isp: Add PHY routing configuration
[media] omap3isp: Add CSI configuration registers from control block to ISP resources
[media] omap3isp: Remove unneeded module memory address definitions
[media] omap3isp: Use monotonic timestamps for statistics buffers
[media] uvcvideo: Fix control value clamping for unsigned integer controls
[media] uvcvideo: Mark first output terminal as default video node
[media] uvcvideo: Add VIDIOC_[GS]_PRIORITY support
[media] uvcvideo: Return -ENOTTY for unsupported ioctls
[media] uvcvideo: Set device_caps in VIDIOC_QUERYCAP
[media] uvcvideo: Don't fail when an unsupported format is requested
[media] uvcvideo: Return -EACCES when trying to access a read/write-only control
[media] uvcvideo: Set error_idx properly for extended controls API failures
[media] rtl28xxu: add NOXON DAB/DAB+ USB dongle rev 2
[media] fc2580: write some registers conditionally
...
The winbond hardware has a counter for leading edges, which increases as
they are received. As we read raw IR from a fifo in an interrupt handler,
we cannot correlate them to specific IR pulses so we simply count all
pulses and edges until we go idle and disable the receiver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The receiver is never disabled by idle mode since rxstate never gets set
to RXSTATE_ACTIVE, so we keep on getting interrupts after the first IR
activity ends. Note that ir_raw_event_reset() already calls
ir_raw_event_handle().
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"54fd321 [media] winbond: remove space from driver name" inadvertently
renamed the input device name.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This makes the cleanup on probe failure more consistent with other
drivers. This is similar to what commit
f27b853ea2 ("[media] rc: Fix invalid
free_region and/or free_irq on probe failure") did for some other
drivers.
In addition to making the cleanup more consistent, this also fixes a
case where (on a ene_hw_detect failure) free_region would be called on a
region that was not requested yet.
This last problem was probably introduced by the moving of code in
commit b31b021988 ("[media] ene_ir: Fix
driver initialisation") and commit
9ef449c6b3 ("[media] rc: Postpone ISR
registration").
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Linux Media Mailing List <linux-media@vger.kernel.org>
drivers/media/rc/fintek-cir.c:687:5: warning: no previous prototype for 'fintek_init' [-Wmissing-prototypes]
drivers/media/rc/fintek-cir.c:692:6: warning: no previous prototype for 'fintek_exit' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The carrier detect return value is never used on nuvoton driver:
drivers/media/rc/nuvoton-cir.c: In function 'nvt_process_rx_ir_data':
drivers/media/rc/nuvoton-cir.c:623:6: warning: variable 'carrier' set but not used [-Wunused-but-set-variable]
Also, this would be called only if a boolean variable is enabled,
but there's no condition that enables it inside the driver. So,
comment the carrier detection code, as it might be useful later,
and remove the unused glue code.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The RC_TYPE_* defines are currently used both where a single protocol is
expected and where a bitmap of protocols is expected.
Functions like rc_keydown() and functions which add/remove entries to the
keytable want a single protocol. Future userspace APIs would also
benefit from numeric protocols (rather than bitmap ones). Keytables are
smaller if they can use a small(ish) integer rather than a bitmap.
Other functions or struct members (e.g. allowed_protos,
enabled_protocols, etc) accept multiple protocols and need a bitmap.
Using different types reduces the risk of programmer error. Using a
protocol enum whereever possible also makes for a more future-proof
user-space API as we don't need to worry about a sufficient number of
bits being available (e.g. in structs used for ioctl() calls).
The use of both a number and a corresponding bit is dalso one in e.g.
the input subsystem as well (see all the references to set/clear bit when
changing keytables for example).
This patch separate the different usages in preparation for
upcoming patches.
Where a single protocol is expected, enum rc_type is used; where one or more
protocol(s) are expected, something like u64 is used.
The patch has been rewritten so that the format of the sysfs "protocols"
file is no longer altered (at the loss of some detail). The file itself
should probably be deprecated in the future though.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Andy Walls <awalls@md.metrocast.net>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We must move this for ARM common zImage support.
Note that neither drivers/media/rc/ir-rx51.c or
drivers/media/platform/omap3isp/ispvideo.c need
to include omap-pm.h, so this patch removes the
include for those files.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: linux-media@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ir-rc from my MSI DigiVox mini II Version 3 (af9015) will not work since
kernel 3.2.x.
sudo ir-keytable -t shows:
1348890734.303273: event MSC: scancode = 317
1348890734.303280: event key down: KEY_POWER (0x0074)
1348890734.303282: event sync
1348890734.553961: event key up: KEY_POWER (0x0074)
1348890734.553963: event sync
1348890741.303451: event MSC: scancode = 30d
1348890741.303457: event key down: KEY_DOWN (0x006c)
1348890741.303459: event sync
1348890741.553956: event key up: KEY_DOWN (0x006c)
So I changed in rc-msi-digivox-ii.c { 0x0002, KEY_2 }, to { 0x0302, KEY_2 },
and so on. And now it works well.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-snip-
ACTION=add
DEVPATH=/devices/pnp0/00:04/rc/rc0
DRV_NAME=Winbond CIR
NAME=rc-rc6-mce
SUBSYSTEM=rc
UDEV_LOG=6
USEC_INITIALIZED=88135858
run: '/usr/bin/ir-keytable -a /etc/rc_maps.cfg -s rc0'
Having a space makes it impossible to match in /etc/rc_maps.cfg.
[root@pequod ~]# udevadm test /sys/class/rc/rc0
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that the firmware already disables the receiver before transmit,
there is no need to do this from the driver.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These should be -ENOSYS because not -EINVAL.
Reported-by: Sean Young <sean@mess.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"carrier" comes from a get_user() in ir_lirc_ioctl(). We need to test
that it's not zero before using it as a divisor. It might have been
nice to test for this ir_lirc_ioctl() but the mceusb driver uses zero to
disable carrier modulation.
The bug in redrat3 is a little more subtle. The ->carrier is passed to
mod_freq_to_val() which uses it as a divisor.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change winbond-cir's tx support to be asynchronous and not to mess with
the TX buffer. Essentially the winbond-cir counterpart to the patch
Sean Young sent for iguanair.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is a minor correctness fix for the duration calculation in
winbond-cir (the read value should be incremented by one).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
DIV_ROUND_CLOSEST is faster if the compiler knows it will only be
dealing with unsigned dividends.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Although this kind of IR diode circuitry is known to exist only in
N900 hardware, nothing prevents making similar circuitry on any OMAP
based board. The MACH_NOKIA_RX51 dependency is thus not something we
want to be there.
Also, this should depend on LIRC as it is a LIRC driver.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-Fix typo
-Change pwm_timer_num type to match type in platform data
-Remove extra parenthesis
-Replace magic constant with proper bit defintions
-Remove duplicate exit pointer
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
While here, fix the led name: the led is green, not yellow.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since commit "[media] rc-core: move timeout and checks to lirc", the
incoming buffer is used after the driver transmits.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
