There is no suspend enable/disable settings mentioned in datasheet,
so just don't implement .set_suspend_[en|dis]able callbacks.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is not required because current code use devm_regulator_register() to
register regulators.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
BUCK 3 and 4 share the same ramp delay. Hence make it a fall through
case instead of duplicating the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
BBCH_BBCHEN_MASK is equivalent to TPS65910_SUPPLY_STATE_ENABLED.
So all regulators have the same enable_mask setting.
BBCH_BBCHEN_MASK and BBCH_BBCHEN_SHIFT are not used now, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add missing .owner field in regulator_desc, which is used for refcounting.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make PFUZE100 entry consistent with other Freescale PMIC entries, so that now
we can have:
<*> Freescale MC13783 regulator driver
<*> Freescale MC13892 regulator driver
<*> Freescale PFUZE100 regulator driver
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Robin Gong <yibin.gong@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
tps65910 has a backup battery charger with a configurable voltage. This
patch adds a regulator for the backup battery.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
These settings are not used when using linear_ranges and it makes the code
looks confusing. Thus remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
MAX14577 chip is a multi-function device which includes MUIC,
charger and voltage regulator. The driver is located in drivers/mfd.
This patch adds regulator driver for MAX14577 chip. There are two
regulators in this chip:
1. Safeout LDO with constant voltage output of 4.9V. It can be only
enabled or disabled.
2. Current regulator for the charger. It provides current from 90mA up
to 950mA.
Driver supports Device Tree.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes a build failure that appeared in v3.13-rc4 due to an
RTC/MFD update merged via -mm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=t/v5
-----END PGP SIGNATURE-----
Merge tag 's2mps11-build' into regulator-s5m8767 since a following patch
depend on it.
regulator/clk: Fix s2mps11 build
This patch fixes a build failure that appeared in v3.13-rc4 due to an
RTC/MFD update merged via -mm.
Replace calls to sec_reg* helpers with direct usage of regmap API. The
sec_reg* helpers are error-prone as they mix u8 with unsigned int and
order of some of parameters (val and mask in sec_reg_update()).
Also the helpers do not give any way of useful abstraction as they just
call corresponding regmap function.
This patch replaces:
- sec_reg_read() with regmap_read(),
- sec_reg_write() with regmap_write(),
- sec_reg_update() with regmap_update_bits().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add symbols for hard-coded values of BUCK_RAMP field in DVS_RAMP
register. This simplifies a little the code as register update is called
only once.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Only print an error when _regulator_get() is expected to return a valid
regulator, that is when _regulator_get() is called from regulator_get() and
we're not using the dummy because we don't have full-constraints, or when
_regulator_get() is called from regulator_get_exclusive() in which case
returning a dummy is not allowed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix building of s2mps11 regulator and clock drivers after renaming
regmap field in struct sec_pmic_dev in commit:
- "mfd/rtc: s5m: Fix register updating by adding regmap for RTC"
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A small set of driver fixes plus one larger core change which changes
the way we check to see if we're using DT so that there aren't any races
between deciding we're using DT and the regulator subsystem noticing.
This makes the new support for substituting a dummy regulator and
optional regulators work a lot better on DT systems since it ensures
that we don't trigger probe deferral when we shouldn't which was causing
bugs in clients.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=WqDN
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"A small set of driver fixes plus one larger core change which changes
the way we check to see if we're using DT so that there aren't any
races between deciding we're using DT and the regulator subsystem
noticing.
This makes the new support for substituting a dummy regulator and
optional regulators work a lot better on DT systems since it ensures
that we don't trigger probe deferral when we shouldn't which was
causing bugs in clients"
* tag 'regulator-v3.13-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: pfuze100: allow misprogrammed ID
regulator: pfuze100: Fix address of FABID
regulator: as3722: set the correct current limit
regulator: core: Check for DT every time we check full constraints
regulator: core: Replace checks of have_full_constraints with a function
Rename old regmap field of "struct sec_pmic_dev" to "regmap_pmic" and
add new regmap for RTC.
On S5M8767A registers were not properly updated and read due to usage of
the same regmap as the PMIC. This could be observed in various hangs,
e.g. in infinite loop during waiting for UDR field change.
On this chip family the RTC has different I2C address than PMIC so
additional regmap is needed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Voltage setting for BUCK7 and BUCK8 was not supported by s5m8767 driver.
If they were configured in DTS then the driver probing would fail with
EINVAL:
[ 0.288474] VCC_SUB_1.35V: failed to apply 1350000uV constraint
[ 0.288671] s5m8767-pmic s5m8767-pmic: regulator init failed for 35
[ 0.294931] s5m8767-pmic: probe of s5m8767-pmic failed with error -22
This patch adds support for BUCK7 and BUCK8 regulators using standard
regmap get/set voltage sel functions.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replace hard-coded value for mask used in BUCKX_CTRL registers (for
BUCKX_EN field) with a symbol. This also removes two local variables.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
prior to week 08 of 2013 Freescale misprogrammed between 1 and 3% of
PFUZE1000 parts with a ID=0x8 instead of the expected ID=0x0
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
According to the datasheet, the address of FABID is 0x4. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Since essentially all GPIO controlled regulators are voltage regulators
make the regulator-type property optional, defaulting to voltage.
Signed-off-by: Mark Brown <broonie@linaro.org>
The Ux500 platform has been converted to do device-tree only
boots, no longer supports platform data passing, so this
probe path is unused. Delete it, simplifying the driver a
whole lot.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simple fix to set the correct current limit for SD0/1/6.
Signed-off-by: Vince Hsu <vinceh@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes: bc407334e9 (regulator: as3722: add regulator driver for AMS AS3722)
Cc: stable@vger.kernel.org
Change the device name of the regulator function to the one chosen for
MODULE_ALIAS. This fixes kernel auto-module loading for the regulator function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Eliminate the gap between DT becoming available and this being used to say
we have full constraints by checking directly for DT every time we check
for full constraints. This improves interoperaton with optional regulator
support.
Signed-off-by: Mark Brown <broonie@linaro.org>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Simple code reorganisation so we can change the logic for deciding what
full constraints are more easily.
Signed-off-by: Mark Brown <broonie@linaro.org>
Both num_regulators and **rdev are no longer required after this conversion,
thus remove them from struct lp3972.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit "i2c: core: make it possible to match a pure device tree driver"
changed semantics of the i2c probing for device tree devices.
Device tree probed devices now get a NULL i2c_device_id pointer.
This causes the regulator name to be set to NULL and the regulator
registration to fail.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
wm5110 provides different voltage configurations than the other Arizona
parts, this patch adds support for this into the regulator driver. Also
fixup the default for the configuration register for wm5110.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org (v3.12)
prior to week 08 of 2013 Freescale misprogrammed between 1 and 3% of
PFUZE1000 parts with a ID=0x8 instead of the expected ID=0x0
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Commit c368e5fc2a "regulator: fixed:
get rid of {get|list}_voltage()" broke regulator_list_voltage() for
the fixed regulator, because an earlier commit
5a523605af "regulator: core: provide
fixed voltage in desc for single voltage rail" missed to add support
for the fixed-voltage special case to that function. This patch
fixes that regression.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both num_regulators and **rdev are no longer required after this conversion,
thus remove them from struct lp3971.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Catch missing regulator-type property in DT and return an error
gracefully instead of deferencing a NULL pointer and crashing.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The s5m8767 regulator driver parse always the voltage table of buck2/3/4.
If gpio_dvs feature isn't used and dts haven't included the voltage table
of buck2/3/4, s5m8767 regulator driver return error and file probe state.
This patch check only voltage table of buck on s5m8767_pmic_dt_parse_pdata()
if buck[2-4]_gpiodvs is true.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch parse 'buck[2-4]_ramp_enable and buck_ramp_delay' platform data
from dts file.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit 68f7506017.
Michael reported that with this patch we loose the fix_io code path from
da9052_reg_update. Thus revert it.
Reported-by: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
These patches add the ability to create an alternative device on which
a lookup for a certain supply should be conducted.
A common use-case for this would be devices that are logically
represented as a collection of drivers within Linux but are are
presented as a single device from device tree. It this case it is
necessary for each sub device to locate their supply data on the main
device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch errors and warning.
ERROR: spaces required around that '=' (ctx:VxV)
ERROR: space required before the open parenthesis '('
WARNING: line over 80 characters
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch warning.
WARNING: line over 80 characters
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch warning.
WARNING: unnecessary whitespace before a quoted newline
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch warnings.
WARNING: Avoid unnecessary line continuations
WARNING: line over 80 characters
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch warnings.
WARNING: Avoid unnecessary line continuations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch warning.
WARNING: quoted string split across lines
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch warnings.
WARNING: please, no spaces at the start of a line
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch warnings.
WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the following checkpatch warning.
WARNING: quoted string split across lines
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Correct spelling typo within various part of the kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add REGULATOR_LINEAR_RANGE macro and convert regulator drivers to use it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
linear ranges means each range has linear voltage settings.
So we can calculate max_uV for each linear range in regulator core rather than
set the max_uV field in drivers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
commit 40b1936e (regulator: Introduce TI Adaptive Body Bias(ABB) on-chip
LDO driver) missed a pair of brackets which cause the wrong vset data to be
picked up from efuse, resulting in bad VBB voltage values.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
As per the devicetree binding document of TPS65910, the "regulators"
subnode should be under the parent node, not outside of parent node.
Hence to get the regulator node, the correct call is
of_get_child_by_name() rather than of_find_node_by_name() which searches
the "regulators" node from the parent node to end of DTS file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per the devicetree binding document of TPS6586x, the "regulators"
subnode should be under the parent node, not outside of parent node.
Hence to get the regulator node, the correct call is
of_get_child_by_name() rather than of_find_node_by_name() which searches
the "regulators" node from the parent node to end of DTS file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per the devicetree binding document of TPS65090, the "regulators"
subnode should be under the parent node, not outside of parent node.
Hence to get the regulator node, the correct call is
of_get_child_by_name() rather than of_find_node_by_name() which searches
the "regulators" node from the parent node to end of DTS file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The device tree binding of Palmas regulator driver says as:
palmas_pmis {
compatible = "ti,palmas-pmic";
...
regulators {
...
}
};
In this "regulators" subnode is expected to be part of parent node, not
the outside of parent node. Hence to get the regulator node, the correct
call is of_get_child_by_name() rather than of_find_node_by_name() which
actually searches the "regulators" node from the parent node to end of DTS
file.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This helps people spot if they have missed a supply from a device tree or
equivalent data structure.
Suggested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
AS3722_SDx_VSEL_MAX means the maximum selecter, the n_voltages should be
AS3722_SDx_VSEL_MAX + 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix off-by-one in the equation to calculate max_uV and also adjust the _min_uV
setting accordingly.
For LDOs:
The voltage select bits set the LDO output voltage 0.825V...3.3V, 25mV steps
....00h : LDO off
01h-24h : V_LDO4 = 0.8V + ldo4_vsel * 25mV
= 0.825V + (ldo4_vsel - 1h) * 25mV
25h-3Fh : do not use
40h-7Fh : V_LDO4 = 1.725V + (ldo4_vsel - 40h) * 25mV
For SD2345:
The voltage select bits set the DC/DC output voltage level and power the DC/DC
converter down.
....00h : DC/DC powered down
01h-40h : V_SD2 = 0.6V + sd2_vsel * 12.5mV
= 0.6125V + (sd2_vsel - 1h) * 12.5mV
41h-70h : V_SD2 = 1.4V + (sd2_vsel - 40h) * 25mV
= 1.425V + (sd2_vsel - 41h) * 25mV
71h-7Fh : V_SD2 = 2.6V + (sd2_vsel - 70h) * 50mV
= 2.65V + (sd2_vsel - 71h) * 50mV
Note, the third entry in as3722_sd2345_ranges is wrong in current code.
Fix it based on the datasheet.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler,
and remove unnecessary remove().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use devm_regulator_register() to make cleanup paths simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Keep busy-wait looping to a minimum while waiting for a regulator to
ramp-up to the target voltage. This follows the guidelines set forth
in Documentation/timers/timers-howto.txt and assumes that regulators
are never enabled in atomic context.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
On platforms like OMAP4460, LDO override is never used. Even though
efuse determines the ABB bias mode to operate at, ABB voltage is
preconfigured in internal efuse registers without the need for
LDO override for bias voltage. So skip optional parameter if
property is not present.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As documented in Application Note SWPA117 v2.1(NDA), LDO override has a
requirement that when switching from Bias active + override active
mode(FBB/RBB) to Bypass(nominal) mode, LDO reset must be performed
*after* LDO transitions to Bypass(nominal) mode.
The same rule in reverse applies when switching from a ABB bypass mode
to ABB enabled - LDO override *must* be performed prior to transition to
required ABB mode, if we do not do that, the same glitch takes place.
Currently while transitioning to ABB bypass, we reset the LDO overide
prior to the transition which causes a few milliseconds where ABB LDO
voltage could go all the way to 800mV(based on SoC process node),
during this period, the delta voltage between VDD rail and VBB rail
could cause the system to improperly function.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This patch adds basic Device Tree support to the da9210 regulator driver -
with no special properties, since also driver's platform data only contains
standard regulator initialisation parameters.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Ensure that the return value is always set when we return now that the
logic has changed for regulator_get_optional() so we don't get missing
codes leaking out.
Reported-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix the linear range settings in commit 5ff26a14c3
"regulator: wm831x-ldo: Convert to use linear ranges".
For wm831x_gp_ldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xe:
volt = 0.9-1.6V in 50mV steps
sel <= 0x1f:
volt = 1.7-3.3V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
For wm831x_aldo:
We have below equations for list voltage before converting to linear ranges:
sel <= 0xc:
volt = 1-1.6V in 50mV steps
sel <= 0x1f
volt = 1.7-3.5V in 100mV steps
max_uV for the first linear range should be 1600000 rather than 1650000. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The AMS AS3722 is a compact system PMU suitable for mobile phones,
tablets etc. It has 4 DCDC step down regulators, 3 DCDC step down
controller, 11 LDOs.
Add a driver to support accessing the DCDC/LDOs found on the AMS
AS3722 PMIC using regulators.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Florian Lobmaier <florian.lobmaier@ams.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now that we are defaulting to providing dummy regulators fix the logic
for substituting a dummy by making the default return code -EPROBE_DEFER.
Reported-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Machine constraints is configured during regulator register. If current
constraints are provided through machine constraints then it is observed
that sometime the current configured on rail is out of range what machine
constraint has.
Set the current constraints when setting machine constraints to make
sure that rail's current is within the range of given machine constraints.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Driver core sets driver data to NULL upon failure or remove.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per datasheet, voltage range for LDOs are as follows:
0000 = 0.9V
...(50mV steps)
01111 = 1.65V
10000 = 1.8V
... (100mV stepns)
11111 = 3.3V
So, there is no selector for 1.65V to 1.8V.
Correcting the range for max_uV for selector between 0 to 15.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The turn-on time of the regulator depends on the regulator device's
electrical characteristics. Sometimes regulator turn-on time also
depends on the capacitive load on the given platform and it can be
more than the datasheet value.
The driver provides the enable-time as per datasheet.
Add support for configure the enable ramp time through regulator
constraints so that regulator core can take this value for enable
time for that regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current equation on the comment is wrong.
For linear mapping starting from 0, the equation is (maxV-minV)/stepV + 1.
Since the linear mapping for PALMAS is not all starting from 0, the equation
on the comment is not useful and misleading. Thus remove it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The ST Microelectronics STw481x PMIC used for the Nomadik
has one single software-controlled regulator for VMMC.
This driver registers directly to the compatible string
as there is just one regulator.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per datasheet (Referred TPS65913), the on-time for LDO is
500micro second. If LDO6 is in vibrator mode then the on-time
is 2000us.
Set the enable_time on regulator descriptor accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Palmas rails like LDOs, SMPSs, REGENs, SYSENs can be enable and disable
by register programming through I2C communication as well as it can be
enable/disable with the external control input ENABLE1, ENABLE2 and NSLEEP.
Add support for configuring these rails to be controlled by external control
inputs. This is require to configure the rail's control register as well as
configuration of resource register.
Provide the external input names through parameter "roof-floor". Updated the
DT binding document to details different value of the roof-floor.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No boards have used this functionality and the new default of providing
dummy regulators by default provides a better solution to the problem it
was trying to solve.
Signed-off-by: Mark Brown <broonie@linaro.org>
When a system has said that it has fully specified constraints for its
regulators it is still possible that some supplies may be missing,
especially if regulator support has been added to a driver after the
board was integrated. We can handle such situations more gracefully by
providing a dummy regulator.
Unless the caller has specifically indicated that the system design may
not include a given regulator by using regulator_get_optional() or that
it needs its interactions to have an effect using regulator_get_exclusive()
provide a dummy regulator if we can't locate a real one.
The kconfig option REGULATOR_DUMMY that provided similar behaviour for all
regulators has been removed, systems that need it should flag that they
have full constraints instead.
Signed-off-by: Mark Brown <broonie@linaro.org>
Cut down on the size of core.c a bit more and ensure that the devres
versions of things don't do too much peering inside the internals of
the APIs they wrap.
Signed-off-by: Mark Brown <broonie@linaro.org>
The implementation of devm_regulator_get, devm_regulator_get_exclusive and
devm_regulator_get_optional are almost the same.
Introduce _devm_regulator_get helper function and refactor the code.
Also move devm_regulator_get_exclusive to proper place, put it after
regulator_get_exclusive() function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commmit af40a94aba "regulator: palmas: Use devm_regulator_register" missed
removing a regulator_unregister() call if palmas_extreg_init falis. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
NULL assignment corrupts the error pointer and is not
necessary.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
devm_* simplifies the code.
[Fixups from rebase onto v3.12 code -- broonie]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit e398b51a ("regulator: s2mps11: Convert to devm_regulator_register()")
intended to do this conversion. However the actual conversion to devm_* got
missed out. Fix this.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Many regulator drivers have a remove function that consists solely of
calling regulator_unregister() so provide a devm_regulator_register()
in order to allow this repeated code to be removed and help eliminate
error handling code.
Signed-off-by: Mark Brown <broonie@linaro.org>
With gcc 4.1.2:
drivers/regulator/da9063-regulator.c: In function ‘da9063_regulator_probe’:
drivers/regulator/da9063-regulator.c:847: warning: ‘da9063_reg_matches’ is used
uninitialized in this function
If the parent device already has platform data, da9063_reg_matches will
not be initialized.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide the rail supply voltage through descriptor to the
core and remove the callbacks which implement the get_voltage
and list_voltage.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If given rail has the single voltage (n_voltages = 1) then provide the
rail voltage through regulator descriptor so that core can use this
value for finding voltage.
This will avoid the implementation of the callback for get_voltage() or
list_voltage() callback on regulator driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If CONFIG_OF=n:
drivers/regulator/da9063-regulator.c: In function ‘da9063_parse_regulators_dt’:
drivers/regulator/da9063-regulator.c:712: warning: passing argument 1 of ‘PTR_ERR’ makes pointer from integer without a cast
drivers/regulator/da9063-regulator.c:712: warning: return makes pointer from integer without a cast
Use ERR_PTR() to encode an error code in a pointer.
PTR_ERR() is meant to decode an error code from a pointer.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
As per datasheet (Referred TPS65913), the on-time for LDO is
500micro second. If LDO6 is in vibrator mode then the on-time
is 2000us.
Set the enable_time on regulator descriptor accordingly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LeaW
-----END PGP SIGNATURE-----
Merge tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull PTR_RET() removal patches from Rusty Russell:
"PTR_RET() is a weird name, and led to some confusing usage. We ended
up with PTR_ERR_OR_ZERO(), and replacing or fixing all the usages.
This has been sitting in linux-next for a whole cycle"
[ There are still some PTR_RET users scattered about, with some of them
possibly being new, but most of them existing in Rusty's tree too. We
have that
#define PTR_RET(p) PTR_ERR_OR_ZERO(p)
thing in <linux/err.h>, so they continue to work for now - Linus ]
* tag 'PTR_RET-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
GFS2: Replace PTR_RET with PTR_ERR_OR_ZERO
Btrfs: volume: Replace PTR_RET with PTR_ERR_OR_ZERO
drm/cma: Replace PTR_RET with PTR_ERR_OR_ZERO
sh_veu: Replace PTR_RET with PTR_ERR_OR_ZERO
dma-buf: Replace PTR_RET with PTR_ERR_OR_ZERO
drivers/rtc: Replace PTR_RET with PTR_ERR_OR_ZERO
mm/oom_kill: remove weird use of ERR_PTR()/PTR_ERR().
staging/zcache: don't use PTR_RET().
remoteproc: don't use PTR_RET().
pinctrl: don't use PTR_RET().
acpi: Replace weird use of PTR_RET.
s390: Replace weird use of PTR_RET.
PTR_RET is now PTR_ERR_OR_ZERO(): Replace most.
PTR_RET is now PTR_ERR_OR_ZERO
With the following change
---------
commit ad02e84687
Author: Axel Lin <axel.lin@ingics.com>
regulator: palmas: Return raw register values as the selectors in [get|set]_voltage_sel
Don't adjust the selector in [get|set]_voltage_sel, fix it in list_voltage() instead.
For smps*(except smps10), the vsel reg-value and voltage mapping as below:
----------
The list_voltage() takes the true value of selector which is
programmed in the register. As per smsp voltage table
reg-value volt (uV) ( Assume RANGE is x1 )
0 0
1 500000
2 500000
3 500000
4 500000
5 500000
6 500000 (0.49V + 1 * 0.01V) * RANGE
7 510000 (0.49V + 2 * 0.01V) * RANGE
8 520000 (0.49V + 3 * 0.01V) * RANGE
9 530000 (0.49V + 4 * 0.01V) * RANGE
....
121 1650000 (0.49V + 116 * 0.1) * RANGE
Hence making n_voltages for smps to 122.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
da9063_ldo_lim_event() is only referenced in this driver, make it static.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
lp872x regulator driver can be built a module after commit 631a1fc
"regulator: build: Allow most regulators to be built as modules".
Make REGULATOR_LP872X depend on I2C to allow building lp872x module when I2C=m.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Below is the equation in original code:
tps65217_uv1_ranges:
0 ... 24: uV = vsel * 25000 + 900000;
25 ... 52: uV = (vsel - 24) * 50000 + 1500000;
= (vsel - 25) * 50000 + 1550000;
53 ... 55: uV = (vsel - 52) * 100000 + 2900000;
= (vsel - 53) * 100000 + 3000000;
56 ... 62: uV = 3300000;
tps65217_uv2_ranges:
0 ... 8: uV = vsel * 50000 + 1500000;
9 ... 13: uV = (vsel - 8) * 100000 + 1900000;
= (vsel - 9) * 100000 + 2000000;
14 ... 31: uV = (vsel - 13) * 50000 + 2400000;
= (vsel - 14) * 50000 + 2450000;
The voltage tables are composed of linear ranges.
This patch converts this driver to use multiple linear ranges APIs.
In original code, voltage range for DCDC1 is 900000 ~ 1800000 and voltage range
for DCDC3 is 900000 ~ 1500000. This patch separates the range 25~52 in
tps65217_uv1_ranges table to two linear ranges: 25~30 and 31~52.
This change makes it possible to reuse the same linear_ranges table for DCDCx.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
regulator_register() does not return NULL, it returns ERR_PTR on error.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
All the current limit tables have the values in ascend order.
So we can slightly optimize the for loop iteration because the first match
is the minimal value.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a resource managed regulator_get_exclusive()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver adds support for the following DA9063 PMIC regulators:
- 11x LDOs (named LDO1 - LDO11),
- 6x buck converters (BCORE1, BCORE2, BPRO, BMEM, BIO, BPERI),
Regulators provide following operations:
- REGULATOR_CHANGE_STATUS and REGULATOR_CHANGE_VOLTAGE for all regulators,
- REGULATOR_CHANGE_MODE for LDOs and buck converters, where:
- LDOs allow REGULATOR_MODE_NORMAL and REGULATOR_MODE_STANDBY,
- buck converters allow REGULATOR_MODE_FAST, REGULATOR_MODE_NORMAL
and REGULATOR_MODE_STANDBY,
- REGULATOR_CHANGE_CURRENT for buck converters (current limits).
The driver generates REGULATOR_EVENT_OVER_CURRENT for LDO3, LDO4, LDO7, LDO8
and LDO11.
Internally, PMIC provides two voltage configurations for normal and suspend
system state for each regulator. The driver switches between those on
suspend/wake-up to provide quick and fluent output voltage change.
This driver requires MFD core driver for operation.
Signed-off-by: Krystian Garbaciak <krystian.garbaciak@diasemi.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource_byname when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,e,e1;
expression ret != 0;
identifier l;
@@
res = platform_get_resource_byname(...);
- if (res == NULL) { ... \(goto l;\|return ret;\) }
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is supposed to be testing "i < ARRAY_SIZE()" instead of just
"ARRAY_SIZE()".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The modalias is set by the MODULE_DEVICE_TABLE, thus remove redundant
MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The code to check whether num_regulator is valid is wrong because it should
iterate all array entries rather than break from the for loop if
pdata->regulators[i] is NULL.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code has wrong mask and val arguments for updating ramp_delay. Fix it.
Also ensure the return value of get_ramp_delay() won't greater than 3 because
the mask field for ramp_val only takes 2 bits.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code calls regmap_update_bits() with mask and val arguments swapped.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SMPS10 has two outputs OUT1 and OUT2 and have one input IN1.
SMPS10-OUT2 is connected to SMPS10-IN1 and can be configured either
in BOOST mode or BYPASS mode. regulator_enable of SMPS10-OUT2 configures
it in BOOST mode. For BYPASS mode regulator_allow_bypass() API can be
used. SMPS10-OUT1 is connected to SMPS10-OUT2 and can be enabled using
regulator_enable().
[ axel.lin@ingics.com : Simplify regulator_desc setting for SMPS10_[OUT1|OUT2]
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Move regulator_list_voltage_{linear,linear_range,table} helper functions to
helpers.c.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix a build warning for !CONFIG_OF and a cast from void* to
unsigned int which is invalid on 64bit machines.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
I2C driver for the Dialog DA9210 Multi-phase 12A DC-DC Buck.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: David Dajun Chen <david.chen@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds devicetree bindings for max8660, along with some
documentation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
max_register should be register count - 1.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
No functional change, just makes the code shorter.
[Resolved conflict with platdata patch -- broonie]
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduce an enum and denote the device type via struct i2c_id's
driver_data field rather than comparing strings.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify the equation to calculate ramp_delay.
Below equations are equivalent:
ramp_delay = 25000 / (2 * ramp_delay);
ramp_delay = 50000 / (4 * ramp_delay);
ramp_delay = 25000 / (2 * ramp_delay);
ramp_delay = 12500 / ramp_delay;
So we don't need to read BIT6 of rdev->desc->vsel_reg for applying different
equations.
Also use rdev->desc->vsel_reg instead of run-time calculate register address.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While the majority of supplies on devices are mandatory and can't be
physically omitted for electrical reasons some devices do have optional
supplies and need to know if they are missing, MMC being the most common
of these.
Currently the core accurately reports all errors when regulators are
requested since it does not know if the supply is one that must be provided
even if by a regulator software does not know about or if it is one that
may genuinely be disconnected. In order to allow this behaviour to be
changed and stub regulators to be provided in the former case add a new
regulator request function regulator_get_optional() which provides a hint
to the core that the regulator may genuinely not be connected.
Currently the implementation is identical to the current behaviour, future
patches will add support in the core for returning stub regulators in the
case where normal regulator_get() fails and the board has requested it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code adjust min_uV and uV_step but missed adjusting the n_voltages
setting.
When BIT6 is clear:
n_voltages = (1975000 - 400000) / 25000 + 1 = 64
When BIT6 is set:
n_voltages = (3300000 - 800000) / 50000 + 1 = 51
The n_voltages needs update because when BIT6 is set 0x73 ~ 0x7f are reserved.
When using regulator_list_voltage_linear, the n_voltages does matter here
because wrong n_voltages setting make the equation return wrong result.
e.g. if selector is 63, regulator_list_voltage_linear returns
800000 + (50000 * 63) = 4000000
It should return -EINVAL if the selector is in the range of 51 ~ 63.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
All table based voltage list have ascendant order.
Use regulator_map_voltage_ascend for them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
