There is no need to check for regulator presence in the ->suspend()
since a wrapper does it for us. Due to this we may unconditionally set
AFTER_SUSPEND_POWER flag.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make use of device property API in this driver so that both OF based
system and ACPI based system can use this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). This comes with a small functional change: previously
all errors were ignored when platform data is present. Now all errors are
treated as errors. If no input clock is present devm_clk_get_optional() will
return NULL instead of an error which matches the behavior of the old code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the pre device-tree ARM aera there were board files that configured
the system (instead of a device tree). A "struct spi_board_info" was
used to describe the SPI bus.
As new systems should be described via device trees, this patch removes
the board setup example from the driver. The "struct
mcp251x_platform_data" cannot be removed completely, as there are still
some in-tree users of this file.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove checking the wake pin for every read/write call.
The device is not explicitly put to sleep in the code
and the POR interrupt is cleared during the init of
the device.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove the data-ready gpio interrupt handling and use the spi->irq
that is created based on the interrupt DT property.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The system clock frequency for the bus connected to the PCIe controller
shall be used when calculating the frequency of the PWM, not the CAN
system clock frequency.
Signed-off-by: Christer Beskow <chbe@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Every mvpp2 unit can use up to 8 buffers mapped by the BM (the HW buffer
manager). The HW will place the frames in the buffer pool depending on the
frame size: short (< 128 bytes), long (< 1664) or jumbo (up to 9856).
As any unit can have up to 4 ports, the driver allocates only 2 pools,
one for small and one long frames, and share them between ports.
When the first port MTU is set higher than 1664 bytes, a third pool is
allocated for jumbo frames.
This shared allocation makes impossible to use percpu allocators,
and creates contention between HW queues.
If possible, i.e. if the number of possible CPU are less than 8 and jumbo
frames are not used, switch to a new scheme: allocate 8 per-cpu pools for
short and long frames and bind every pool to an RXQ.
When the first port MTU is set higher than 1664 bytes, the allocation
scheme is reverted to the old behaviour (3 shared pools), and when all
ports MTU are lowered, the per-cpu buffers are allocated again.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor mvpp2_bm_pool_create(), mvpp2_bm_pool_destroy() and
mvpp2_bm_pools_init() so that they accept a struct device instead
of a struct platform_device, as they just need platform_device->dev.
Removing such dependency makes the BM code more reusable in context
where we don't have a pointer to the platform_device.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Take only FIB events that are happening in init_net into account. No other
namespaces are supported.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .serdes_irq_setup are all following the same steps: get the SERDES
lane, get the IRQ mapping, request the IRQ, then enable it. So do
the .serdes_irq_free implementations: get the SERDES lane, disable
the IRQ, then free it.
This patch removes these operations in favor of generic functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_status operation to prepare the abstraction
of IRQ thread from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_enable operation to prepare the abstraction
of IRQ enabling from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the first step of all .serdes_power implementations is getting
the lane mapping. Since we have an operation for that, call it in
the wrapper and pass the lane down to the .serdes_power operation.
This also allows to avoid querying the SERDES lane twice in
mv88e6xxx_port_set_cmode.
At the same time provide mv88e6xxx_serdes_power_{up,down} helpers
and prefer up/down instead of on/off as in the documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352_serdes_power_set helper is only used at one place, in
mv88e6352_serdes_power. Keep it simple and merge the two functions
together.
Use mv88e6xxx_serdes_get_lane instead of mv88e6352_port_has_serdes
to avoid moving code. No functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though 88E6352 has no dedicated lane for SERDES interfaces, it
uses a similar code as the other .serdes_get_lane implementations to
check the port's CMODE and ensure that SERDES operations are doable.
For consistency, implement mv88e6352_serdes_get_lane for the 88E6352
and similar switches which simply returns an unused 0xff lane address.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the mapping between a SERDES interface and its lane is static,
we don't need to stick with negative error codes actually and we can
simply return 0 if there is no lane, just like the IRQ mapping.
This way we can keep a simple and intuitive API using unsigned lane
numbers while simplifying the implementations with single return
statements. Last but not least, fix the reverse chrismas tree in
mv88e6390x_serdes_get_lane.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a new .serdes_irq_mapping operation to prepare the
abstraction of IRQ mapping from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mv88e6xxx SERDES code checks for negative error code from
irq_find_mapping, while this function returns an unsigned integer. This
patch removes this dead code and simply returns 0 is no IRQ is found.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6352_serdes_irq_link helper is not checking for any error that
may occur during hardware accesses. Worst, the "up" boolean is set from
the potentially unused "status" variable, if read operations failed.
As done in mv88e6390_serdes_irq_link_sgmii, return right away and do
not call dsa_port_phylink_mac_change if an error occurred.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function 'hclge_restore_vlan_table':
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:8016:18: warning:
variable 'qos' set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 70a214903d ("net: hns3: reduce the parameters of some functions")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer reg_info is being initialized with a value that is never read and
is being re-assigned a little later on. The assignment is redundant
and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 99cd149efe ("sgiseeq: replace use of dma_cache_wback_inv"),
a call to 'get_zeroed_page()' has been turned into a call to
'dma_alloc_coherent()'. Only the remove function has been updated to turn
the corresponding 'free_page()' into 'dma_free_attrs()'.
The error hndling path of the probe function has not been updated.
Fix it now.
Rename the corresponding label to something more in line.
Fixes: 99cd149efe ("sgiseeq: replace use of dma_cache_wback_inv")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8125 uses a different register for VLAN offloading config,
therefore don't set bit RxVlan.
Fixes: f1bce4ad2f ("r8169: add support for RTL8125")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call to 'pci_free_irq_vectors()' are missing both in the error handling
path of the probe function, and in the remove function.
Add them.
Fixes: 19971f5ea0 ("enetc: add PTP clock driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change enables the use of SW timestamping on the Raspberry Pi 4.
bcmgenet's transmit function bcmgenet_xmit() implements software
timestamping. However the SOF_TIMESTAMPING_TX_SOFTWARE capability was
missing and only SOF_TIMESTAMPING_RX_SOFTWARE was announced. By using
ethtool_ops bcmgenet_ethtool_ops() as get_ts_info(), the
SOF_TIMESTAMPING_TX_SOFTWARE capability is announced.
Similar to commit a8f5cb9e79 ("smsc95xx: use ethtool_op_get_ts_info()")
Signed-off-by: Ryan M. Collins <rmc032@bucknell.edu>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a 3-Port 10/100 Ethernet Switch with 1588v2 PTP.
Signed-off-by: Razvan Stefanescu <razvan.stefanescu@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On embedded environments with hard memory limits it is a normal although
rare case when skb can't be allocated on rx part under high traffic.
In such OOM cases napi_complete_done() was not called.
So the napi object became in an invalid state like it is "scheduled".
Kernel do not re-schedules the poll of that napi object.
Consequently, kernel can not remove that object the system hangs on
`ifconfig down` waiting for a poll.
We are fixing this by gracefully closing napi poll routine with correct
invocation of napi_complete_done.
This was reproduced with artificially failing the allocation of skb to
simulate an "out of memory" error case and check that traffic does
not get stuck.
Fixes: 970a2e9864 ("net: ethernet: aquantia: Vector operations")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declaring threaded irq handler should also indicate the irq is
oneshot. It is oneshot indeed, because HW implements irq automasking
on trigger.
Not declaring this causes some kernel configurations to fail
on interface up, because request_threaded_irq returned an err code.
The issue was originally hidden on normal x86_64 configuration with
latest kernel, because depending on interrupt controller, irq driver
added ONESHOT flag on its own.
Issue was observed on older kernels (4.14) where no such logic exists.
Fixes: 4c83f170b3 ("net: aquantia: link status irq handling")
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reported-by: Michael Symolkin <Michael.Symolkin@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of device reconfiguration the driver may reset the device invisible
for other modules, vlan module in particular. So vlans will not be
removed&created and vlan filters will not be configured in the device.
The patch reapplies the vlan filters at device start.
Fixes: 7975d2aff5 ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a limit condition of vlans on the interface before setting vlan
promiscuous mode
Fixes: 48dd73d08d ("net: aquantia: fix vlans not working over bridged network")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to absence of checking against the rx flow rule when vlan 0 is being
removed, the other rule could be removed instead of the rule with vlan 0
Fixes: 7975d2aff5 ("net: aquantia: add support of rx-vlan-filter offload")
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver support for configuring grc dump config flags, and
dumping the grc data via ethtool get/set-dump interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for configuring the grc dump config flags.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver support for dumping the config id attributes via ethtool dump
interfaces.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for reading the config id attributes from NVM
flash partition.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the register value width as the regmap_config name to prevent the
following error when the second and third regmap_configs are
initialized.
"debugfs: Directory '${bus-id}' with parent 'regmap' already present!"
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2019-08-31
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Fix 32-bit zero-extension during constant blinding which
has been causing a regression on ppc64, from Naveen.
2) Fix a latency bug in nfp driver when updating stack index
register, from Jiong.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new function bnxt_get_registered_vfs() to handle the work
of getting the number of registered VFs under #ifdef CONFIG_BNXT_SRIOV.
The main code will call this function and will always work correctly
whether CONFIG_BNXT_SRIOV is set or not.
Fixes: 230d1f0de7 ("bnxt_en: Handle firmware reset.")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New local variable "struct flow_block_offload *f" was added to
mlx5e_setup_tc() in recent rtnl lock removal patches. The variable is used
in code that is only compiled when CONFIG_MLX5_ESWITCH is enabled. This
results compilation warning about unused variable when CONFIG_MLX5_ESWITCH
is not set. Move the variable definition into eswitch-specific code block
from the beginning of mlx5e_setup_tc() function.
Fixes: c9f14470d0 ("net: sched: add API for registering unlocked offload block callbacks")
Reported-by: tanhuazhong <tanhuazhong@huawei.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 190f73ab4c ("net: stmmac: setup higher frequency clk support for EHL & TGL")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devicetree binding lists the phy phy as optional. As such, the
driver should not bail out if it can't find a regulator. Instead it
should just skip the remaining regulator related code and continue
on normally.
Skip the remainder of phy_power_on() if a regulator supply isn't
available. This also gets rid of the bogus return code.
Fixes: 2e12f53663 ("net: stmmac: dwmac-rk: Use standard devicetree property for phy regulator")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In xgbe_mod_init(), we should do cleanup if some error occurs
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: efbaa82833 ("amd-xgbe: Add support to handle device renaming")
Fixes: 47f164deab ("amd-xgbe: Add PCI device support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer pkt is being initialized with a value that is never read
and pkt is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Ununsed value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Health show command example and output:
$ devlink health show pci/0000:af:00.0 reporter fw_fatal
pci/0000:af:00.0:
name fw_fatal
state healthy error 1 recover 1 grace_period 0 auto_recover true
Fatal events from firmware or missing periodic heartbeats will
be reported and recovery will be handled.
We also turn on the support flags when we register with the firmware to
enable this health and recovery feature in the firmware.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This call will handle fatal firmware errors by forcing a reset on the
firmware. The master function driver will carry out the forced reset.
The sequence will go through the same bnxt_fw_reset_task() workqueue.
This fatal reset differs from the non-fatal reset at the beginning
stages. From the BNXT_FW_RESET_STATE_ENABLE_DEV state onwards where
the firmware is coming out of reset, it is practically identical to the
non-fatal reset.
The next patch will add the periodic heartbeat check and the devlink
reporter to report the fatal event and to initiate the bnxt_fw_exception()
call.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
