The Lenovo Yoga 920-13IKB does not have a hw rfkill switch, and trying
to read the hw rfkill switch through the ideapad module causes it to
always report as blocked.
This commit adds the Lenovo Yoga 920-13IKB to the no_hw_rfkill dmi list,
fixing the WiFI breakage.
Signed-off-by: Philipp Hug <philipp@hug.cx>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Radio LED detection method implemented in commit 4f62568c1f
("fujitsu-laptop: Support radio LED") turned out to be incorrect as it
causes a radio LED to be erroneously detected on a Fujitsu Lifebook E751
which has a slide switch (and thus no radio LED). Use bit 17 of
flags_supported (the value returned by method S000 of ACPI device
FUJ02E3) to determine whether a radio LED is present as it seems to be a
more reliable indicator, based on comparing DSDT tables of four Fujitsu
Lifebook models (E744, E751, S7110, S8420).
Fixes: 4f62568c1f ("fujitsu-laptop: Support radio LED")
Reported-by: Heinrich Siebmanns <harv@gmx.de>
Signed-off-by: Michał Kępień <kernel@kempniu.pl>
Tested-by: Heinrich Siebmanns <harv@gmx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Added support for HP ProBook 440 G4 laptops by including the accelerometer
orientation quirk for that device. Testing was performed based on the
axis orientation guidelines here:
https://www.kernel.org/doc/Documentation/misc-devices/lis3lv02d
which states "If the left side is elevated, X increases (becomes positive)".
When tested, on lifting the left edge, x values became increasingly negative
thus indicating an inverted x-axis on the installed lis3lv02d chip.
This was compensated by adding an entry for this device in hp_accel.c
specifying the quirk as x_inverted. The patch was tested on a
ProBook 440 G4 device and x-axis as well as y and z-axis values are now
generated as per spec.
Signed-off-by: Osama Khan <osama.khan@ericsson.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Ev Kontsevoy reported that he can't see the presence of
"/proc/sys/kernel/sched_itmt_enabled" on i9-7900x with Asrock x299
Taichi system even if he enabled "Turbo 3.0" in the BIOS.
The problem is that even if one core max is 200MHz more than others, the
current implementation couldn't enumerate that with the way the system
is configured.
The system by default configured for legacy mode (no HWP or speed shift
technology), in this mode only way we can enumerate via the mail box
interface as implemented in this driver. We were planing to only use
this driver for Broadwell, but we need to extend this because some
Skylake system has same issue as Braodwell systems.
On this system BIOS allows to change to HWP mode, where we expect that
we can enumerate favored core with ACPI-CPPC. But on this system the
core priority is 0xff for all cores in CPPC object. So this is not an
option.
Hence this change allows Skylake systems to be enumerate favored core
similar to Broadwell in legacy mode.
Reported-and-tested-by: Ev Kontsevoy <ev@kontsevoy.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
'default n' is a default behaviour of Kconfig options. So, remove
explicit line from Kconfig.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
linux/io.h defines readq() and ioremap_nocache() / iounmap() functions.
If not included, the build fails:
intel_telemetry_pltdrv.c:1165:31: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
intel_telemetry_pltdrv.c:1165:33: error: implicit declaration of function 'ioremap_nocache' [-Werror=implicit-function-declaration]
intel_telemetry_pltdrv.c:1202:3: error: implicit declaration of function 'iounmap' [-Werror=implicit-function-declaration]
intel_telemetry_pltdrv.c:900:20: error: implicit declaration of function 'readq' [-Werror=implicit-function-declaration]
Fix this by including linux/io.h.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Currently, update_no_reboot_bit() function implemented in this driver
uses mutex_lock() to protect its register updates. But this function is
called with in atomic context in iTCO_wdt_start() and iTCO_wdt_stop()
functions in iTCO_wdt.c driver, which in turn causes "sleeping into
atomic context" issue. This patch fixes this issue by replacing the
mutex_lock() with spin_lock() to protect the GCR read/write/update APIs.
Fixes: 9d855d4 ("platform/x86: intel_pmc_ipc: Fix iTCO_wdt GCS memory mapping failure")
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kupuswamy@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Removes unnecessary header files included in the driver and sorts the
remaining ones in the alphabetical order.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Telemetry word is misspelled several times in this file as Telemtry. This
fixes the spelling mistake and folds in another minor typo.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Intel Telemetry driver depends on IPC1 interface. If IPC1 interface is
disabled on a given platform by the system firmware, the driver does not
load but prints misleading information in the dmesg logs.
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The functions cht_int33fe_check_for_max17047 and cht_int33fe_find_max17047
are local to the source and do not need to be in global scope, so make
them static.
Cleans up sparse warnings:
symbol 'cht_int33fe_check_for_max17047' was not declared. Should it be
static?
symbol 'cht_int33fe_find_max17047' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The structures mlxplat_dev and mlxplat_hotplug are local to the source
and do not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'mlxplat_dev' was not declared. Should it be static?
symbol 'mlxplat_hotplug' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Add touchscreen platform data for the Chuwi Hi8 Pro tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
This patch removes the FSF address from the GPL notice to fix a
checkpatch.pl CHECK message.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There are fields in the struct ips_mcp_limits which are not used
anywhere and a label which we may get rid of.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use devm_ and pcim_ functions to make error handling
simpler and code smaller and tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It seems that the WMI GUID used by the PEAQ 2-in-1 WMI hotkeys is not
as unique as a GUID should be and is used on some other devices too.
This is causing spurious key-press reports on these other devices.
This commits adds a DMI check to the PEAQ 2-in-1 WMI hotkeys driver to
ensure that it is actually running on a PEAQ 2-in-1, fixing the
spurious key-presses on these other devices.
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1497861
BugLink: https://bugzilla.suse.com/attachment.cgi?id=743182
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
peaq-wmi on Lenovo ideapad 700-15ISK keeps sending KEY_SOUND,
which makes user's repeated keys gets interrupted.
The system does not have Dolby button, let's blacklist it.
BugLink: https://bugs.launchpad.net/bugs/1720219
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch cleans up unnecessary free/alloc calls in ipc_plat_probe(),
ipc_pci_probe() and ipc_plat_get_res() functions by using devm_*
calls.
This patch also adds proper error handling for failure cases in
ipc_pci_probe() function.
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
[andy: fixed style issues, missed devm_free_irq(), removed unnecessary log message]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Many thinkpad laptops and convertibles provide the GMMS method to
resolve how far the laptop has been opened and whether it has been
converted into tablet mode. This allows reporting a more precise tablet
mode state to userspace.
The current implementation only reports a summarized tablet mode state
which is triggered as soon as the input devices become unusable as they
are folded away from the display.
This will work on all models where the CMMD method was used previously and
it may also work in other cases.
Thanks to Peter Zhang of Lenovo for providing information on how to use the
GMMS method to query the tablet mode.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Cc: Peter FP1 Zhang <zhangfp1@lenovo.com>
Cc: Lyude Paul <lyude@redhat.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
My Fujitsu-Siemens Lifebook S6120 doesn't have the FUJ02E3 device,
but it does have FUJ02B1. That means we do register the backlight
device (and it even seems to work), but the code will oops as soon
as we try to set the backlight brightness because it's trying to
call call_fext_func() with a NULL device. Let's just skip those
function calls when the FUJ02E3 device is not present.
Cc: Jonathan Woithe <jwoithe@just42.net>
Cc: Andy Shevchenko <andy@infradead.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # 4.13.x
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
device_create documentation says to cleanup using device_destroy
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The initialize routine is:
* class -> bus -> platform
The exit routine is:
* platform -> class -> bus
Fix the exit routine to be:
* platform -> bus -> class
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The include list is randomly assembled right now. Sort in alphabetical
order.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
pr_fmt provides formatting to be used by the driver when
displaying errors and messages.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Pali Pohar <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
The descriptor GUID is not used to indicate that WMI notifications
in the dell-wmi driver work properly. As such a modalias should
not be present that causes this driver to load on systems with this
GUID.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Pali Pohar <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
This driver serves the purpose of responding to WMI based notifications
from the DELL_EVENT_GUID (9DBB5994-A997-11DA-B012-B622A1EF5492).
Other GUIDs will be handled by separate drivers.
Update the language used by this driver to avoid future confusion.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Some Asus laptops (ROG series for example) are provided with a lightbar
behind the monitor. This patch make possible to switch it on and off.
This lightbar works exactly like any other led.
Signed-off-by: Maxime Bellengé <maxime.bellenge@gmail.com>
[dvhart: fix commit message format and variable declaration order]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
On Dell Latitude 7275 the 5-button array is not exposed in the ACPI
tables, but notififies are still sent to the Intel HID device object
(device ID INT33D5) in response to power button actions. They were
ignored as the intel-hid driver was not prepared to take care of them
until recently.
Power button wakeup from suspend-to-idle was added in:
commit 635173a17b ("intel-hid: Wake up Dell Latitude 7275 from suspend-to-idle")
However power button suspend doesn't work yet on this platform so it
would be good to add it also.
On the affected platform (for which priv->array is NULL), add a new
upfront check against the power button press notification (0xCE) to
notify_handler(), outside the wakeup mode this time, which allows
reporting the power button press event and triggers the suspend. Also
catch and ignore the corresponding power button release notification
(0xCF) to stop it from being reported as an "unknown event" in the logs.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196115
Tested-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Signed-off-by: Jérôme de Bretagne <jerome.debretagne@gmail.com>
Acked-By: Mario Limonciello <mario.limonciello@dell.com>
[dvhart: minor coding style and commit message format fix]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
These were raised by Lukas Wunner as potential DOS attacks against
the system log by passing bad data to sysfs.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Use the standard ARRAY_SIZE() macro instead of the custom
TELEM_EVT_LEN().
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
At least one BIOS enumerates the max17047 both through the INT33FE ACPI
device (it is right there in the resources table) as well as through a
separate MAX17047 device.
This commit checks for the max17047 already being enumerated through
a separate MAX17047 ACPI device and if so it uses the i2c-client
instantiated for this and attaches the device-props for the max17047 to
that i2c-client.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Current implementations of Intel Thunderbolt controllers will go
into a low power mode when not in use.
Many machines containing these controllers also have a GPIO wired up
that can force the controller awake. This is offered via a ACPI-WMI
interface intended to be manipulated by a userspace utility.
This mechanism is provided by Intel to OEMs to include in BIOS.
It uses an industry wide GUID that is populated in a separate _WDG
entry with no binary MOF.
This interface allows software such as fwupd to wake up thunderbolt
controllers to query the firmware version or flash new firmware.
Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <yehezkel.bernat@intel.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
[andy fixed merge conflicts and bump kernel version for ABI]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Several fixes from static analysis and message noise reduction. Correct
WMI core and related drivers to evaluate instance number 0x0 in
accordance with the documentation. Add intel-telemetry support for
Gemini Lake. Various individual driver fixes noted below.
Two commits appear here which were previously merged during the 4.13 RC
cycle:
- baa5480b05 platform/x86: dell-wmi: Fix driver interface version query
- c801603e6d platform/x86: intel-vbtn: match power button on press rather than release
dell-wmi:
- Update dell_wmi_check_descriptor_buffer() to new model
intel-vbtn:
- reduce unnecessary messages for normal users
- match power button on press rather than release
intel-hid:
- reduce unnecessary messages for normal users
thinkpad_acpi:
- Fix warning about deprecated hwmon_device_register
wmi:
- Fix check for method instance number
ideapad-laptop:
- Expose conservation mode switch
intel_pmc_core:
- Make the driver PCH family agnostic
peaq-wmi:
- Evaluate wmi method with instance number 0x0
- silence a static checker warning
mxm-wmi:
- Evaluate wmi method with instance number 0x0
asus-wmi:
- Evaluate wmi method with instance number 0x0
intel_scu_ipc:
- make intel_scu_ipc_pdata_t const
intel_mid_powerbtn:
- make mid_pb_ddata const
- fix error return code in mid_pb_probe()
hp-wmi:
- Remove unused macro helper
- Correctly determine method id in WMI calls
dell-wmi:
- Fix driver interface version query
intel_telemetry:
- remove redundant macro definition
- Add GLK PSS Event Table
alienware-wmi:
- fix format string overflow warning
ibm_rtl:
- remove unnecessary static in ibm_rtl_write()
msi-wmi:
- remove unnecessary static in msi_wmi_notify()
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJZsvdiAAoJEKbMaAwKp364V+UIAI27WP1MKQ6zKiXAt6TTLQww
RGbeTrgxsHwxIp1ioo3MZtRa4uTMrJ/A/Es7nzZBSAAp8qPLOCaZYGtsH0tYkzcc
zGLw+q5EBEjiMiq8WvkgD+NLq6icdsB0MUuuh06y34/LWiOwpp9wNemszHO9Vo2/
vc5PkgNmMx5K4zJvl6A3JAY98XlXxG65vYMrsIL17EFwZjuixrcCjDY86HKxEnNV
tmfJ1Mhiu5HnDniCgRubdRBo4LwAeRdrXXkrsTZip+4RuXvm0gvxHujwgllIY4Ns
m6xFXQApaGtXxd9vcSBHXE7whTgWrb7yPhUQzgt/Dd3E6ywF2THfn5jvwJUEflc=
=LuAp
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.14-1' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"Several fixes from static analysis and message noise reduction.
Correct WMI core and related drivers to evaluate instance number 0x0
in accordance with the documentation. Add intel-telemetry support for
Gemini Lake. Various individual driver fixes noted below.
dell-wmi:
- Update dell_wmi_check_descriptor_buffer() to new model
intel-vbtn:
- reduce unnecessary messages for normal users
- match power button on press rather than release
intel-hid:
- reduce unnecessary messages for normal users
thinkpad_acpi:
- Fix warning about deprecated hwmon_device_register
wmi:
- Fix check for method instance number
ideapad-laptop:
- Expose conservation mode switch
intel_pmc_core:
- Make the driver PCH family agnostic
peaq-wmi:
- Evaluate wmi method with instance number 0x0
- silence a static checker warning
mxm-wmi:
- Evaluate wmi method with instance number 0x0
asus-wmi:
- Evaluate wmi method with instance number 0x0
intel_scu_ipc:
- make intel_scu_ipc_pdata_t const
intel_mid_powerbtn:
- make mid_pb_ddata const
- fix error return code in mid_pb_probe()
hp-wmi:
- Remove unused macro helper
- Correctly determine method id in WMI calls
dell-wmi:
- Fix driver interface version query
intel_telemetry:
- remove redundant macro definition
- Add GLK PSS Event Table
alienware-wmi:
- fix format string overflow warning
ibm_rtl:
- remove unnecessary static in ibm_rtl_write()
msi-wmi:
- remove unnecessary static in msi_wmi_notify()"
* tag 'platform-drivers-x86-v4.14-1' of git://git.infradead.org/linux-platform-drivers-x86: (23 commits)
platform/x86: dell-wmi: Update dell_wmi_check_descriptor_buffer() to new model
platform/x86: intel-vbtn: reduce unnecessary messages for normal users
platform/x86: intel-hid: reduce unnecessary messages for normal users
platform/x86: thinkpad_acpi: Fix warning about deprecated hwmon_device_register
platform/x86: wmi: Fix check for method instance number
platform/x86: ideapad-laptop: Expose conservation mode switch
platform/x86: intel_pmc_core: Make the driver PCH family agnostic
platform/x86: peaq-wmi: Evaluate wmi method with instance number 0x0
platform/x86: mxm-wmi: Evaluate wmi method with instance number 0x0
platform/x86: asus-wmi: Evaluate wmi method with instance number 0x0
platform/x86: intel_scu_ipc: make intel_scu_ipc_pdata_t const
platform/x86: intel_mid_powerbtn: make mid_pb_ddata const
platform/x86: intel_mid_powerbtn: fix error return code in mid_pb_probe()
platform/x86: hp-wmi: Remove unused macro helper
platform/x86: hp-wmi: Correctly determine method id in WMI calls
platform/x86: intel-vbtn: match power button on press rather than release
platform/x86: dell-wmi: Fix driver interface version query
platform/x86: intel_telemetry: remove redundant macro definition
platform/x86: intel_telemetry: Add GLK PSS Event Table
platform/x86: alienware-wmi: fix format string overflow warning
...
* pm-sleep:
ACPI / PM: Check low power idle constraints for debug only
PM / s2idle: Rename platform operations structure
PM / s2idle: Rename ->enter_freeze to ->enter_s2idle
PM / s2idle: Rename freeze_state enum and related items
PM / s2idle: Rename PM_SUSPEND_FREEZE to PM_SUSPEND_TO_IDLE
ACPI / PM: Prefer suspend-to-idle over S3 on some systems
platform/x86: intel-hid: Wake up Dell Latitude 7275 from suspend-to-idle
PM / suspend: Define pr_fmt() in suspend.c
PM / suspend: Use mem_sleep_labels[] strings in messages
PM / sleep: Put pm_test under CONFIG_PM_SLEEP_DEBUG
PM / sleep: Check pm_wakeup_pending() in __device_suspend_noirq()
PM / core: Add error argument to dpm_show_time()
PM / core: Split dpm_suspend_noirq() and dpm_resume_noirq()
PM / s2idle: Rearrange the main suspend-to-idle loop
PM / timekeeping: Print debug messages when requested
PM / sleep: Mark suspend/hibernation start and finish
PM / sleep: Do not print debug messages by default
PM / suspend: Export pm_suspend_target_state
This converts dell_wmi_check_descriptor_buffer() to the new driver
model interface and puts the interface version in dell_wmi_priv
where it belongs.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Unsupported events is only useful for developers and does not meaningful
for users. Using dev_dbg makes more sense and reduces noise in kernel
messages.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Unsupported events is only useful for developers and does not meaningful
for users. Using dev_dbg makes more sense and reduces noise in kernel
messages.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
Use hwmon_device_register_with_groups instead of deprecated
hwmon_device_register and fix a dmesg warning.
This patch however changes the userspace API.
hwmon_device_register_with_groups takes `hwmon' name as an argument and
creates a name file in the `hwmon' device, not in the `platform_device'.
This allows us to remove custom `name' device attribute, but in order to
make lm-sensors happy we also have to move fans and thermal attributes
to the `hwmon' device.
Even though this patch changes userspace API, it's still compatible with
the lm-sensors. Starting with lm-sensors 3.0 (circa 2007), it looks at
both hwmon and the backing device for the name and other attributes.
before:
$ cat /sys/devices/platform/thinkpad_hwmon/{name,fan1_input}
thinkpad
2007
$ cat /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon1/{name,fan1_input}
cat: /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon1/name: No such file or directory
cat: /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon1/fan1_input: No such file or directory
$ cat /sys/class/hwmon/hwmon1/{name,fan1_input}
cat: /sys/class/hwmon/hwmon1/name: No such file or directory
cat: /sys/class/hwmon/hwmon1/fan1_input: No such file or directory
$ sensors
thinkpad-isa-0000
Adapter: ISA adapter
fan1: 3533 RPM
after:
$ cat /sys/devices/platform/thinkpad_hwmon/{name,fan1_input}
cat: /sys/devices/platform/thinkpad_hwmon/name: No such file or directory
cat: /sys/devices/platform/thinkpad_hwmon/fan1_input: No such file or directory
$ cat /sys/devices/platform/thinkpad_hwmon/hwmon/hwmon1/{name,fan1_input}
thinkpad
3478
$ cat /sys/class/hwmon/hwmon1/{name,fan1_input}
thinkpad
3478
$ sensors
thinkpad-isa-0000
Adapter: ISA adapter
fan1: 3489 RPM
$ sensors -v
sensors version 3.4.0 with libsensors version 3.4.0
Signed-off-by: Stanislav Fomichev <kernel@fomichev.me>
[dvhart: cleaned up commit log, bumped version to 4.14 in the doc change]
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
instance_count defines number of instances of data block and instance
itself is indexed from zero, which means first instance has number 0.
Therefore check for invalid instance should be non-strict inequality.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Darren Hart (VMware) <dvhart@infradead.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This exposes the battery conservation mode present on some (?) IdeaPads.
The mode is set by calling ACPI method SBMC with argument 3 (on) or
5 (off). Status is reported in bit 5 of the return value of ACPI method
GBMD.
Signed-off-by: Hao Wei Tee <angelsl@in04.sg>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Although this driver did pretty good job in abstracting PCH specific
interfaces, but still there are some loose ends. For example
SLP_S0 counter (for reading SLP_S0 residency), PM config offset (for
checking permissions to read XRAM) and PPFEAR offset (for reading IP
status) is still hardcoded for a specific family of PCH.
This change extended the struct pmc_reg_map to allow per family
configuration of offsets and bits.
No functional change is expected with this change. This change allows
seamless additions to new PCH and create a baseline for other platform
specific extensions.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
According to Hans de Goede, WMI interface of thh peaq-wmi module has 10
instances but corresponding ACPI WMBC method does not check Arg0 (instance
number) at all. Therefore evaluate WMI method with first instance number
(0x0) instead of second (0x1).
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
According to MXM 2.1 specification, there is the only one instance of the
WMI GUID F6CB5C3C-9CAE-4EBD-B577-931EA32A2CC0 and so it is instance 0x0.
MXM 2.1 specification:
https://lekensteyn.nl/files/docs/mxm-2.1-software-spec.pdf
_WDG dump:
// Methods GUID {F6CB5C3C-9CAE-4EBD-B577-931EA32A2CC0}
0x3C, 0x5C, 0xCB, 0xF6, 0xAE, 0x9C, 0xBD, 0x4E, 0xB5, 0x77, 0x93,
0x1E, 0xA3, 0x2A, 0x2C, 0xC0,
0x4D, 0x58, // Object ID "MX" = method "WMMX"
1, // Instance Count
0x02, // Flags (WMIACPI_REGFLAG_METHOD)
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
