Currently there's no way to enable wbt if it's not enabled in the
kernel config by default for a device. Allow a write to the
'wbt_lat_usec' queue sysfs file to enable wbt.
This is useful for both the kernel config case, but also if the
device is CFQ managed and it was turned off by default.
Signed-off-by: Jens Axboe <axboe@fb.com>
Make it clear that we are disabling wbt for the specified queued,
if it was enabled by default. This is in preparation for allowing
users to re-enable wbt, and not have it disabled automatically
again.
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow a write of '-1' to reset the default latency target for
a given device. This removes knowledge of the different default
settings for rotational vs non-rotational from user space.
Signed-off-by: Jens Axboe <axboe@fb.com>
blkcg allocates some per-cgroup data structures with GFP_NOWAIT and
when that fails falls back to operations which aren't specific to the
cgroup. Occassional failures are expected under pressure and falling
back to non-cgroup operation is the right thing to do.
Unfortunately, I forgot to add __GFP_NOWARN to these allocations and
these expected failures end up creating a lot of noise. Add
__GFP_NOWARN.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Marc MERLIN <marc@merlins.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Some drivers often use external bvec table, so introduce
this helper for this case. It is always safe to access the
bio->bi_io_vec in this way for this case.
After converting to this usage, it will becomes a bit easier
to evaluate the remaining direct access to bio->bi_io_vec,
so it can help to prepare for the following multipage bvec
support.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixed up the new O_DIRECT cases.
Signed-off-by: Jens Axboe <axboe@fb.com>
If a ZBC device is partitioned and operations are performed on the partition
the zone information is rebased to the partition, however the zone reset
is not mapped from the partition to device as are other operations.
This causes the API (report zones / reset zone) to be unbalanced in this
regard. Checking for the zone reset op code explicitly will balance the
API.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The previous commit introduced the hybrid sleep/poll mode. Take
that one step further, and use the completion latencies to
automatically sleep for half the mean completion time. This is
a good approximation.
This changes the 'io_poll_delay' sysfs file a bit to expose the
various options. Depending on the value, the polling code will
behave differently:
-1 Never enter hybrid sleep mode
0 Use half of the completion mean for the sleep delay
>0 Use this specific value as the sleep delay
Signed-off-by: Jens Axboe <axboe@fb.com>
Tested-By: Stephen Bates <sbates@raithlin.com>
Reviewed-By: Stephen Bates <sbates@raithlin.com>
This patch enables a hybrid polling mode. Instead of polling after IO
submission, we can induce an artificial delay, and then poll after that.
For example, if the IO is presumed to complete in 8 usecs from now, we
can sleep for 4 usecs, wake up, and then do our polling. This still puts
a sleep/wakeup cycle in the IO path, but instead of the wakeup happening
after the IO has completed, it'll happen before. With this hybrid
scheme, we can achieve big latency reductions while still using the same
(or less) amount of CPU.
Signed-off-by: Jens Axboe <axboe@fb.com>
Tested-By: Stephen Bates <sbates@raithlin.com>
Reviewed-By: Stephen Bates <sbates@raithlin.com>
The newly added driver causes a harmless warning in some configurations:
block/blk-wbt.c:250:1: error: ‘inline’ is not at beginning of declaration [-Werror=old-style-declaration]
static bool inline stat_sample_valid(struct blk_rq_stat *stat)
This makes it use the expected format for the declaration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
In both legacy and mq path, req count of plug list is computed
before allocating request, so the number can be stale when falling
back to slept allocation, also the new introduced wbt can sleep
too.
This patch deals with the case by checking if plug list becomes
empty, and fixes the KASAN report of 'BUG: KASAN: stack-out-of-bounds'
which is introduced by Shaohua's patches of dispatching big request.
Fixes: 600271d900002(blk-mq: immediately dispatch big size request)
Fixes: 50d24c34403c6(block: immediately dispatch big size request)
Cc: Shaohua Li <shli@fb.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Again a leftover from when the throttling code was generic. Now that we
just have the block user, get rid of the stat ops and indirections.
Signed-off-by: Jens Axboe <axboe@fb.com>
The bdi was a leftover from when the code was block layer agnostic.
Now that we just support a block layer user, store the queue directly.
Signed-off-by: Jens Axboe <axboe@fb.com>
The poll code is blk-mq specific, let's move it to blk-mq.c. This
is a prep patch for improving the polling code.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
A previous commit changed this to pass in the hardware queue, but
it was using the wrong hardware queue. Hence a request that was
allocated on one hardware queue ended up being issued on another
one, and that caused IO timeouts and oopses on some drivers. Since
the request holds hardware queue private resources, like a tag,
we can't just issue it on a different hardware queue.
Fixes: 2253efc850 ("blk-mq: Move more code into blk_mq_direct_issue_request()")
Signed-off-by: Jens Axboe <axboe@fb.com>
Enable throttling of buffered writeback to make it a lot
more smooth, and has way less impact on other system activity.
Background writeback should be, by definition, background
activity. The fact that we flush huge bundles of it at the time
means that it potentially has heavy impacts on foreground workloads,
which isn't ideal. We can't easily limit the sizes of writes that
we do, since that would impact file system layout in the presence
of delayed allocation. So just throttle back buffered writeback,
unless someone is waiting for it.
The algorithm for when to throttle takes its inspiration in the
CoDel networking scheduling algorithm. Like CoDel, blk-wb monitors
the minimum latencies of requests over a window of time. In that
window of time, if the minimum latency of any request exceeds a
given target, then a scale count is incremented and the queue depth
is shrunk. The next monitoring window is shrunk accordingly. Unlike
CoDel, if we hit a window that exhibits good behavior, then we
simply increment the scale count and re-calculate the limits for that
scale value. This prevents us from oscillating between a
close-to-ideal value and max all the time, instead remaining in the
windows where we get good behavior.
Unlike CoDel, blk-wb allows the scale count to to negative. This
happens if we primarily have writes going on. Unlike positive
scale counts, this doesn't change the size of the monitoring window.
When the heavy writers finish, blk-bw quickly snaps back to it's
stable state of a zero scale count.
The patch registers a sysfs entry, 'wb_lat_usec'. This sets the latency
target to me met. It defaults to 2 msec for non-rotational storage, and
75 msec for rotational storage. Setting this value to '0' disables
blk-wb. Generally, a user would not have to touch this setting.
We don't enable WBT on devices that are managed with CFQ, and have
a non-root block cgroup attached. If we have a proportional share setup
on this particular disk, then the wbt throttling will interfere with
that. We don't have a strong need for wbt for that case, since we will
rely on CFQ doing that for us.
Signed-off-by: Jens Axboe <axboe@fb.com>
We can hook this up to the block layer, to help throttle buffered
writes.
wbt registers a few trace points that can be used to track what is
happening in the system:
wbt_lat: 259:0: latency 2446318
wbt_stat: 259:0: rmean=2446318, rmin=2446318, rmax=2446318, rsamples=1,
wmean=518866, wmin=15522, wmax=5330353, wsamples=57
wbt_step: 259:0: step down: step=1, window=72727272, background=8, normal=16, max=32
This shows a sync issue event (wbt_lat) that exceeded it's time. wbt_stat
dumps the current read/write stats for that window, and wbt_step shows a
step down event where we now scale back writes. Each trace includes the
device, 259:0 in this case.
Signed-off-by: Jens Axboe <axboe@fb.com>
For legacy block, we simply track them in the request queue. For
blk-mq, we track them on a per-sw queue basis, which we can then
sum up through the hardware queues and finally to a per device
state.
The stats are tracked in, roughly, 0.1s interval windows.
Add sysfs files to display the stats.
The feature is off by default, to avoid any extra overhead. In-kernel
users of it can turn it on by setting QUEUE_FLAG_STATS in the queue
flags. We currently don't turn it on if someone just reads any of
the stats files, that is something we could add as well.
Signed-off-by: Jens Axboe <axboe@fb.com>
cfq_cpd_alloc() which is the cpd_alloc_fn implementation for cfq was
incorrectly hard coding GFP_KERNEL instead of using the mask specified
through the @gfp parameter. This currently doesn't cause any actual
issues because all current callers specify GFP_KERNEL. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: e4a9bde958 ("blkcg: replace blkcg_policy->cpd_size with ->cpd_alloc/free_fn() methods")
Signed-off-by: Jens Axboe <axboe@fb.com>
If we insert a flush request, we clear REQ_PREFLUSH and/or REQ_FUA,
depending on flush settings. Since op_is_sync() factors those flags
in for deciding whether this request is sync or not, we should
set REQ_SYNC to avoid screwing up this accounting.
This should be less fragile.
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: b685d3d65a ("block: treat REQ_FUA and REQ_PREFLUSH as synchronous")
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 0e87e58bf6 ("blk-mq: improve warning for running a queue on the
wrong CPU") attempts to avoid triggering the WARN_ON in
__blk_mq_run_hw_queue when the expected CPU is dead. Problem is, in the
last batch execution before round robin, blk_mq_hctx_next_cpu can
schedule a dead CPU and also update next_cpu to the next alive CPU in
the mask, which will trigger the WARN_ON despite the previous
workaround.
The following patch fixes this scenario by always scheduling the value
in hctx->next_cpu. This changes the moment when we round-robin the CPU
running the hctx, but it really doesn't matter, since it still executes
BLK_MQ_CPU_WORK_BATCH times in a row before switching to another CPU.
Fixes: 0e87e58bf6 ("blk-mq: improve warning for running a queue on the wrong CPU")
Signed-off-by: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For blk-mq, ->nr_requests does track queue depth, at least at init
time. But for the older queue paths, it's simply a soft setting.
On top of that, it's generally larger than the hardware setting
on purpose, to allow backup of requests for merging.
Fill a hole in struct request with a 'queue_depth' member, that
drivers can call to more closely inform the block layer of the
real queue depth.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Jan Kara <jack@suse.cz>
This is corresponding part for blk-mq. Disk with multiple hardware
queues doesn't need this as we only hold 1 request at most.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently block plug holds up to 16 non-mergeable requests. This makes
sense if the request size is small, eg, reduce lock contention. But if
request size is big enough, we don't need to worry about lock
contention. Holding such request makes no sense and it lows the disk
utilization.
In practice, this improves 10% throughput for my raid5 sequential write
workload.
The size (128k) is arbitrary right now, but it makes sure lock
contention is small. This probably could be more intelligent, eg, check
average request size holded. Since this is mainly for sequential IO,
probably not worthy.
V2: check the last request instead of the first request, so as long as
there is one big size request we flush the plug.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
bsg_validate_sgv4_hdr() doesn't care about the request_queue, so drop it
from it's arguments.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Most blk_mq_requeue_request() and blk_mq_add_to_requeue_list() calls
are followed by kicking the requeue list. Hence add an argument to
these two functions that allows to kick the requeue list. This was
proposed by Christoph Hellwig.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_mq_quiesce_queue() waits until ongoing .queue_rq() invocations
have finished. This function does *not* wait until all outstanding
requests have finished (this means invocation of request.end_io()).
The algorithm used by blk_mq_quiesce_queue() is as follows:
* Hold either an RCU read lock or an SRCU read lock around
.queue_rq() calls. The former is used if .queue_rq() does not
block and the latter if .queue_rq() may block.
* blk_mq_quiesce_queue() first calls blk_mq_stop_hw_queues()
followed by synchronize_srcu() or synchronize_rcu(). The latter
call waits for .queue_rq() invocations that started before
blk_mq_quiesce_queue() was called.
* The blk_mq_hctx_stopped() calls that control whether or not
.queue_rq() will be called are called with the (S)RCU read lock
held. This is necessary to avoid race conditions against
blk_mq_quiesce_queue().
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since blk_mq_requeue_work() no longer restarts stopped queues
canceling requeue work is no longer needed to prevent that a
stopped queue would be restarted. Hence remove this function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since blk_mq_requeue_work() starts stopped queues and since
execution of this function can be scheduled after a queue has
been stopped it is not possible to stop queues without using
an additional state variable to track whether or not the queue
has been stopped. Hence modify blk_mq_requeue_work() such that it
does not start stopped queues. My conclusion after a review of
the blk_mq_stop_hw_queues() and blk_mq_{delay_,}kick_requeue_list()
callers is as follows:
* In the dm driver starting and stopping queues should only happen
if __dm_suspend() or __dm_resume() is called and not if the
requeue list is processed.
* In the SCSI core queue stopping and starting should only be
performed by the scsi_internal_device_block() and
scsi_internal_device_unblock() functions but not by any other
function. Although the blk_mq_stop_hw_queue() call in
scsi_queue_rq() may help to reduce CPU load if a LLD queue is
full, figuring out whether or not a queue should be restarted
when requeueing a command would require to introduce additional
locking in scsi_mq_requeue_cmd() to avoid a race with
scsi_internal_device_block(). Avoid this complexity by removing
the blk_mq_stop_hw_queue() call from scsi_queue_rq().
* In the NVMe core only the functions that call
blk_mq_start_stopped_hw_queues() explicitly should start stopped
queues.
* A blk_mq_start_stopped_hwqueues() call must be added in the
xen-blkfront driver in its blkif_recover() function.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Roger Pau Monné <roger.pau@citrix.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: James Bottomley <jejb@linux.vnet.ibm.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Move the "hctx stopped" test and the insert request calls into
blk_mq_direct_issue_request(). Rename that function into
blk_mq_try_issue_directly() to reflect its new semantics. Pass
the hctx pointer to that function instead of looking it up a
second time. These changes avoid that code has to be duplicated
in the next patch.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The function blk_queue_stopped() allows to test whether or not a
traditional request queue has been stopped. Introduce a helper
function that allows block drivers to query easily whether or not
one or more hardware contexts of a blk-mq queue have been stopped.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Multiple functions test the BLK_MQ_S_STOPPED bit so introduce
a helper function that performs this test.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The meaning of the BLK_MQ_S_STOPPED flag is "do not call
.queue_rq()". Hence modify blk_mq_make_request() such that requests
are queued instead of issued if a queue has been stopped.
Reported-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
This is a helper that pins down a range from an iov_iter and adds it to
a bio without requiring a separate memory allocation for the page array.
It will be used for upcoming direct I/O implementations for block devices
and iomap based file systems.
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[hch: ported to the iov_iter interface, renamed and added comments.
All blame should be directed to me and all fame should go to Kent
after this!]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Remove the WRITE_* and READ_SYNC wrappers, and just use the flags
directly. Where applicable this also drops usage of the
bio_set_op_attrs wrapper.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Noidle should be the default for writes as seen by all the compounds
definitions in fs.h using it. In fact only direct I/O really should
be using NODILE, so turn the whole flag around to get the defaults
right, which will make our life much easier especially onces the
WRITE_* defines go away.
This assumes all the existing "raw" users of REQ_SYNC for writes
want noidle behavior, which seems to be spot on from a quick audit.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we don't need the common flags to overflow outside the range
of a 32-bit type we can encode them the same way for both the bio and
request fields. This in addition allows us to place the operation
first (and make some room for more ops while we're at it) and to
stop having to shift around the operation values.
In addition this allows passing around only one value in the block layer
instead of two (and eventuall also in the file systems, but we can do
that later) and thus clean up a lot of code.
Last but not least this allows decreasing the size of the cmd_flags
field in struct request to 32-bits. Various functions passing this
value could also be updated, but I'd like to avoid the churn for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
A lot of the REQ_* flags are only used on struct requests, and only of
use to the block layer and a few drivers that dig into struct request
internals.
This patch adds a new req_flags_t rq_flags field to struct request for
them, and thus dramatically shrinks the number of common requests. It
also removes the unfortunate situation where we have to fit the fields
from the same enum into 32 bits for struct bio and 64 bits for
struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It's the last bio-only REQ_* flag, and we have space for it in the bio
bi_flags field.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
With the addition of the zoned operations the tests in this function
became incorrect. But I think it's much better to just open code the
allow operations in the only caller anyway.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We can just use struct blk_mq_alloc_data - it has a few more
members, but we allocate it further down the stack anyway. So
this cleans up the code, and reduces the stack overhead a bit.
Signed-off-by: Jens Axboe <axboe@fb.com>
If we end up sleeping due to running out of requests, we should
update the hardware and software queues in the map ctx structure.
Otherwise we could end up having rq->mq_ctx point to the pre-sleep
context, and risk corrupting ctx->rq_list since we'll be
grabbing the wrong lock when inserting the request.
Reported-by: Dave Jones <davej@codemonkey.org.uk>
Reported-by: Chris Mason <clm@fb.com>
Tested-by: Chris Mason <clm@fb.com>
Fixes: 63581af3f3 ("blk-mq: remove non-blocking pass in blk_mq_map_request")
Signed-off-by: Jens Axboe <axboe@fb.com>
The blkdev_report_zones produces a harmless warning when
-Wmaybe-uninitialized is set, after gcc gets a little confused
about the multiple 'goto' here:
block/blk-zoned.c: In function 'blkdev_report_zones':
block/blk-zoned.c:188:13: error: 'nz' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Moving the assignment to nr_zones makes this a little simpler
while also avoiding the warning reliably. I'm removing the
extraneous initialization of 'int ret' in the same patch, as
that is semi-related and could cause an uninitialized use of
that variable to not produce a warning.
Fixes: 6a0cb1bc10 ("block: Implement support for zoned block devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Adds the new BLKREPORTZONE and BLKRESETZONE ioctls for respectively
obtaining the zone configuration of a zoned block device and resetting
the write pointer of sequential zones of a zoned block device.
The BLKREPORTZONE ioctl maps directly to a single call of the function
blkdev_report_zones. The zone information result is passed as an array
of struct blk_zone identical to the structure used internally for
processing the REQ_OP_ZONE_REPORT operation. The BLKRESETZONE ioctl
maps to a single call of the blkdev_reset_zones function.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Implement zoned block device zone information reporting and reset.
Zone information are reported as struct blk_zone. This implementation
does not differentiate between host-aware and host-managed device
models and is valid for both. Two functions are provided:
blkdev_report_zones for discovering the zone configuration of a
zoned block device, and blkdev_reset_zones for resetting the write
pointer of sequential zones. The helper function blk_queue_zone_size
and bdev_zone_size are also provided for, as the name suggest,
obtaining the zone size (in 512B sectors) of the zones of the device.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[Damien: * Removed the zone cache
* Implement report zones operation based on earlier proposal
by Shaun Tancheff <shaun.tancheff@seagate.com>]
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Define REQ_OP_ZONE_REPORT and REQ_OP_ZONE_RESET for handling zones of
host-managed and host-aware zoned block devices. With with these two
new operations, the total number of operations defined reaches 8 and
still fits with the 3 bits definition of REQ_OP_BITS.
Signed-off-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The queue limits already have a 'chunk_sectors' setting, so
we should be presenting it via sysfs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[Damien: Updated Documentation/ABI/testing/sysfs-block]
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
