imx25 contains two registers (LPIMR0 and 1) to define which interrupts
are enabled in low-power mode. As of today, those two registers are
configured to enable all interrupts. Before going to low-power mode, the
AVIC's INTENABLEH and INTENABLEL registers are configured to enable only
those interrupts which are used as wakeup sources.
It turned out that this approach is not sufficient if we want the imx25
to go into stop mode during suspend-to-ram. (Stop mode is the low-power
mode that consumes the least power. The peripheral master clock is
switched off in this mode). For stop mode to work, the LPIMR0 and 1
registers have to be configured with the set of interrupts that are
allowed in low-power mode. Fortunately, the bits in the LPIMR registers
are assigned to the same interrupts as the bits in INTENABLEH and
INTENABLEL. However, LPIMR uses 1 to mask an interrupt whereas the
INTENABLE registers use 1 to enable an interrupt.
This patch sets the LPIMR registers to the inverted bitmask of the
INTENABLE registers during suspend and goes back to "all interrupts
masked" when we wake up again. We also make this the default at startup.
As far as I know, the other supported imx architectures have no similar
mechanism. Since the LPIMR registers are part of the CCM module, we
query the device tree for an imx25 ccm node in order to detect if we're
running on imx25.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IRQ number should be translated from VIRQ to HWIRQ for TZIC.
As a solution for this issue, move existing translation code
from AVIC to common place.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead of __raw_*, define imx_* to *_relaxed and use those.
Using imx_* was requested by Arnd because *_relaxed tends to
indicate that the code was carefully reviewed to not require
any synchronisation and otherwise be safe, which isn't the
case here with the automatic conversion.
The conversion itself was done using the following spatch
(since that automatically adjusts the coding style unlike
a simple search&replace).
@@
expression E1, E2;
@@
-__raw_writel(E1, E2)
+imx_writel(E1, E2)
@@
expression E1, E2;
@@
-__raw_writew(E1, E2)
+imx_writew(E1, E2)
@@
expression E1;
@@
-__raw_readl(E1)
+imx_readl(E1)
@@
expression E1;
@@
-__raw_readw(E1)
+imx_readw(E1)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch moves IRQ handler setup to the its corresponded IRQ
driver (AVIC, TZIC).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The code for irq priorisation support doesn't have any in-tree users and
the Kconfig description does wrong promises because nowadays irq
handlers are called with irqs disabled, so no high prioritized irq can
interrupt a lower prioritized handler.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Here is a collection of cleanup patches. Among the pieces that stand out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xCAx
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup from Olof Johansson:
"Here is a collection of cleanup patches. Among the pieces that stand
out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep
them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: i.MX: remove unused ARCH_* configs
ARM i.MX53: remove platform ahci support
ARM: sunxi: Rework the restart code
irqchip: sunxi: Rename sunxi to sun4i
irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
clocksource: sunxi: Rename sunxi to sun4i
clocksource: sunxi: make use of CLKSRC_OF
clocksource: sunxi: Cleanup the timer code
ARM: at91: remove trailing semicolon from macros
ARM: at91/setup: fix trivial typos
ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
ARM: EXYNOS: change the name of USB ohci header
ARM: SAMSUNG: Remove unnecessary code for dma
ARM: S3C24XX: Remove unused GPIO drive strength register definitions
ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
...
When building a kernel with CONFIG_PM undefined, the following warning happens:
arch/arm/mach-imx/avic.c:57:12: warning: 'avic_saved_mask_reg' defined but not used [-Wunused-variable]
Move avic_saved_mask_reg definition inside the '#ifdef CONFIG_PM' block to
avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Fix the following sparse warning:
arch/arm/mach-imx/avic.c:54:14: warning: symbol 'avic_base' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The only mach/irqs.h user outside arch/arm/mach-imx is
sound/soc/fsl/imx-pcm-fiq.c, which refers to mxc_set_irq_fiq().
Move the declaration into include/linux/platform_data/asoc-imx-ssi.h,
so that we can remove mach/irqs.h includsion from imx-pcm-fiq.c.
Inside arch/arm/mach-imx, the only users to mach/irqs.h are avic.c
and tzic.c for referring to macro FIQ_START. Let's move the macro
into irq-common.h and get rid of mach/irqs.h completely.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: alsa-devel@alsa-project.org
It moves a bunch of header files included in hardware.h and itself
from mach-imx/include/mach to mach-imx, and updates users to include
hardware.h rather than mach/hardware.h. The files in mach-imx/devices
will need to include "../hardware.h".
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Rename mach-imx/include/mach/common.h to mach-imx/common.h and update
all users to include common.h rather than mach/common.h.
It also removes an unneeded inclusion to common.h in
mach-imx/devices/devices.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
It's really unnecessary to have plat-mxc, and let's merge it into
mach-imx. It's pretty much just a bunch of file renaming and
Kconfig/Makefile merge.
To make the change less invasive, we keep using Kconfig symbol
CONFIG_ARCH_MXC for mach-imx sub-architecture.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
