Some USB peripheral controller drivers support software control
over the data pullup. Use those controls to prevent the OBEX
function from enumerating until the userspace server has opened
the /dev/ttyGS* node it will use to implement protocol chitchat
with the USB host.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch introduces a new f_obex.c function driver.
It allows userspace obex servers to use usb as transport layer
for their messages.
[ dbrownell@users.sourceforge.net: various fixes and cleanups ]
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new mechanism to the composite gadget framework, letting
functions deactivate (and reactivate) themselves. Think of it
as a refcounted wrapper for the software pullup control.
A key example of why to use this mechanism involves functions that
require a userspace daemon. Those functions shuld use this new
mechanism to prevent the gadget from enumerating until those daemons
are activated. Without this mechanism, hosts would see devices that
malfunction until the relevant daemons start.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1132) implements the set_wedge() method for net2280.
This method is necessary for strict USBCV compliance in
g_file_storage.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1131) implements the set_wedge() method for dummy_hcd.
This method is necessary for strict USBCV compliance in
g_file_storage.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reorders the list of USB peripheral controller drivers so it's
more common for the initial (default) value to be relevant: put the
SOC integrated silicon up front, discrete stuff last. Alphabetize.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[This version fixes a thinko in the r8a66597 driver]
This patch let a few discrete USB host controllers drivers (isp116x-hcd,
r8a66597-hcd and sl811-hcd) obtain IRQ flags from their IORESOURCE_IRQ
resource if configured as such, much like it's been done for the smc91x
driver.
It spares people writing support for specific boards the burden to
configure the interrupt controller independantly, and keeps all IRQ
related information in a single resource.
HCD that are integrally part of a SoC have been left aside, as there
is probably no "wiring" options...
Tested on an Xscale PXA-255 based platform with isp116x-hcd.
Signed-off-by: Marc Zyngier <marc.zyngier@altran.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this extends the poisoning concept to anchors. This way poisoning
will work with fire and forget drivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
looking at usb_kill_urb() it seems to me that it is unnecessarily lenient.
In the use case of disconnect() you never want to use the URB again
(for the same device) But leaving urb->reject elevated will make it easier
to avoid races between read/write and disconnect.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In this code, it is possible to tell statically whether usblp will be NULL
in the error handling code.
Oliver Neukum suggested to make a goto to the final return rather than
return directly.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
identifier f,err,l,l1;
type T;
expression x,E;
statement S;
@@
x = NULL
... when != goto l1;
* x = f(...)
... when != x
err = E;
goto l;
...
* if (x != NULL)
S
return err;
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver was originaly written by Stefan Kopp, but massively
reworked by Greg for submission.
Thanks to Felipe Balbi <me@felipebalbi.com> for lots of work in cleaning
up this driver.
Thanks to Oliver Neukum <oliver@neukum.org> for reviewing previous
versions and pointing out problems.
Cc: Stefan Kopp <stefan_kopp@agilent.com>
Cc: Marcel Janssen <korgull@home.nl>
Cc: Felipe Balbi <me@felipebalbi.com>
Cc: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added basic support for a Delcom USB 7-segment LED Display
Signed-off by: Harrison Metzger <harrisonmetz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add Oceanic PID to ftdi_sio driver
Oceanic dive computers (such as the VT3 --
http://www.oceanicworldwide.com/p_computers_vt3.html) all use an onboard
FTDI serial converter, with the FTDI vid and a PID of 0xf460. The
attached patch adds that pid to ftdi_sio; driver connects to my VT3
after that.
Signed-off-by: Vladimir Vukicevic <vladimir@pobox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove duplicate device ids which are now supported by drivers/usb/net/hso.c
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (46 commits)
UIO: Fix mapping of logical and virtual memory
UIO: add automata sercos3 pci card support
UIO: Change driver name of uio_pdrv
UIO: Add alignment warnings for uio-mem
Driver core: add bus_sort_breadthfirst() function
NET: convert the phy_device file to use bus_find_device_by_name
kobject: Cleanup kobject_rename and !CONFIG_SYSFS
kobject: Fix kobject_rename and !CONFIG_SYSFS
sysfs: Make dir and name args to sysfs_notify() const
platform: add new device registration helper
sysfs: use ilookup5() instead of ilookup5_nowait()
PNP: create device attributes via default device attributes
Driver core: make bus_find_device_by_name() more robust
usb: turn dev_warn+WARN_ON combos into dev_WARN
debug: use dev_WARN() rather than WARN_ON() in device_pm_add()
debug: Introduce a dev_WARN() function
sysfs: fix deadlock
device model: Do a quickcheck for driver binding before doing an expensive check
Driver core: Fix cleanup in device_create_vargs().
Driver core: Clarify device cleanup.
...
dev_WARN is both compacter and gives better debug information
than just a WARN_ON, since people and tools will copy the device
information message together with the WARN_ON in bug reports.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the Ethernet/RNDIS gadget driver builds: don't
use separate compilation, since it works poorly when key
parts are library code (with init sections etc). Instead
be as close as we can to "gcc --combine ...".
This is a bit more complicated than most of the others
because it had to resolve a few symbol collisions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the CDC Composite gadget driver builds: don't
use separate compilation, since it works poorly when key
parts are library code (with init sections etc). Instead
be as close as we can to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the file storage gadget driver builds: don't
use separate compilation, since it works poorly when key
parts are library code (with init sections etc). Instead
be as close as we can to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the printer gadget driver builds: don't use
separate compilation, since it works poorly when key parts
are library code (with init sections etc). Instead be as
close as we can to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the MIDI gadget driver builds: don't use separate
compilation, since it works poorly when key parts are library
code (with init sections etc). Instead be as close as we can
to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the Gadget Zero driver builds: don't use
separate compilation, since it works poorly when key
parts are library code (with init sections etc).
Instead be as close as we can to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change how the serial gadget driver builds: don't use
separate compilation, since it works poorly when key parts
are library code (with init sections etc). Instead be as
close as we can to "gcc --combine ...".
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid using printk_ratelimit() in many places because:
- many were error messages reporting broken hardware (it's useful to
get all of these).
- the message itself wasn't useful so the message has been removed.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
This is a much better version of a previous patch to make the parser
tables constant. Rather than changing the typedef, we put the "const" in
all the various places where its required, allowing the __initconst
exception for nfsroot which was the cause of the previous trouble.
This was posted for review some time ago and I believe its been in -mm
since then.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Cc: Alexander Viro <aviro@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use kref in the USB serial drivers so that we don't free tty structures
from under the URB receive handlers as has historically been the case if
you were unlucky. This also gives us a framework for general tty drivers to
use tty_port objects and refcount.
Contains two err->dev_err changes merged together to fix clashes in the
-next tree.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the private check for the termios_initialized for
the pl2303 usb driver. It forced the baud to 9600 on the first call
to pl2303_set_termios()
Based on the tty changes in the 2.6.27 kernel, the termios passed to
the *_set_termios functions is always populated the first time.
This means there is no need to privately initialize the settings the
first time, and doing so will not allow the use of the kernel
parameter "console=ttyUSB0,115200" as an example.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some reason the oti6858 driver undefines and redefines the dbg
macro. This makes it spew debugging messages at KERN_INFO instead of
KERN_DEBUG.
This patch removes the undef and define making the driver log like every
other USB serial driver.
Signed-off-by: Scott Ashcroft <scott.ashcroft@talk21.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (236 commits)
[ARM] 5300/1: fixup spitz reset during boot
[ARM] 5295/1: make ZONE_DMA optional
[ARM] 5239/1: Palm Zire 72 power management support
[ARM] 5298/1: Drop desc_handle_irq()
[ARM] 5297/1: [KS8695] Fix two compile-time warnings
[ARM] 5296/1: [KS8695] Replace macro's with trailing underscores.
[ARM] pxa: allow multi-machine PCMCIA builds
[ARM] pxa: add preliminary CPUFREQ support for PXA3xx
[ARM] pxa: add missing ACCR bit definitions to pxa3xx-regs.h
[ARM] pxa: rename cpu-pxa.c to cpufreq-pxa2xx.c
[ARM] pxa/zylonite: add support for USB OHCI
[ARM] ohci-pxa27x: use ioremap() and offset for register access
[ARM] ohci-pxa27x: introduce pxa27x_clear_otgph()
[ARM] ohci-pxa27x: use platform_get_{irq,resource} for the resource
[ARM] ohci-pxa27x: move OHCI controller specific registers into the driver
[ARM] ohci-pxa27x: introduce flags to avoid direct access to OHCI registers
[ARM] pxa: move I2S register and bit definitions into pxa2xx-i2s.c
[ARM] pxa: simplify DMA register definitions
[ARM] pxa: make additional DCSR bits valid for PXA3xx
[ARM] pxa: move i2c register and bit definitions into i2c-pxa.c
...
Fixed up conflicts in
arch/arm/mach-versatile/core.c
sound/soc/pxa/pxa2xx-ac97.c
sound/soc/pxa/pxa2xx-i2s.c
manually.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1075 commits)
myri10ge: update driver version number to 1.4.3-1.369
r8169: add shutdown handler
r8169: preliminary 8168d support
r8169: support additional 8168cp chipset
r8169: change default behavior for mildly identified 8168c chipsets
r8169: add a new 8168cp flavor
r8169: add a new 8168c flavor (bis)
r8169: add a new 8168c flavor
r8169: sync existing 8168 device hardware start sequences with vendor driver
r8169: 8168b Tx performance tweak
r8169: make room for more specific 8168 hardware start procedure
r8169: shuffle some registers handling around (8168 operation only)
r8169: new phy init parameters for the 8168b
r8169: update phy init parameters
r8169: wake up the PHY of the 8168
af_key: fix SADB_X_SPDDELETE response
ath9k: Fix return code when ath9k_hw_setpower() fails on reset
ath9k: remove nasty FAIL macro from ath9k_hw_reset()
gre: minor cleanups in netlink interface
gre: fix copy and paste error
...
This avoid the pre-mapping of OHCI controller register space, and the
mapping is made only when necessary (OHCI is probed).
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Direct access to pxa27x specific register PSSR in a generic ohci driver
is no good, introduce pxa27x_clear_otgph() and move the implementation
into processor specific code.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Depending on the order of how resource is defined in the platform
device is not good, use platform_get_{irq,resource} for the IRQ
and memory resources.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Direct access to USB host controller registers is considered to be not
portable, and is usually a bad sign for poorly abstracted interface.
Introduce .flags and .power_on_delay to "struct pxaohci_platform_data"
so that most platforms don't bother to write their own .init/.exit()
sequences.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch (as1135) essentially reverts the major parts of two earlier
patches to usbcore, because they ended up causing a regression.
Trying to recover from transient communication errors can lead to
other problems, because operations that failed during the error period
are not always retried. The simplest example is the initial
Set-Config request sent after device enumeration; if it gets lost then
it will not be retried and the device will remain unconfigured.
This patch restores the old behavior in which any port disconnect or
port disable causes the entire device structure to be removed, fixing a
reported regression.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Nokia 5310 Music Xpress phone reports one too many sectors in
usb-storage mode. This patch resolves that.
Signed-off-by: David Almaroad <dalmaroad@gmail.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In file included from drivers/usb/musb/musb_core.h:59,
from drivers/usb/musb/musb_core.c:108:
drivers/usb/musb/musb_io.h:42: error: conflicting types for '__raw_readsl'
/usr/src/devel/arch/sh/include/asm/io.h:112: error: previous declaration of '__raw_readsl' was here
drivers/usb/musb/musb_io.h:42: error: conflicting types for '__raw_readsl'
/usr/src/devel/arch/sh/include/asm/io.h:112: error: previous declaration of '__raw_readsl' was here
drivers/usb/musb/musb_io.h:44: error: conflicting types for 'readsw'
/usr/src/devel/arch/sh/include/asm/io.h:164: error: previous definition of 'readsw' was here
drivers/usb/musb/musb_io.h:46: error: conflicting types for 'readsb'
/usr/src/devel/arch/sh/include/asm/io.h:163: error: previous definition of 'readsb' was here
drivers/usb/musb/musb_io.h:49: error: conflicting types for '__raw_writesl'
/usr/src/devel/arch/sh/include/asm/io.h:111: error: previous declaration of '__raw_writesl' was here
drivers/usb/musb/musb_io.h:49: error: conflicting types for '__raw_writesl'
/usr/src/devel/arch/sh/include/asm/io.h:111: error: previous declaration of '__raw_writesl' was here
drivers/usb/musb/musb_io.h:51: error: conflicting types for 'writesw'
/usr/src/devel/arch/sh/include/asm/io.h:164: error: previous definition of 'writesw' was here
drivers/usb/musb/musb_io.h:53: error: conflicting types for 'writesb'
/usr/src/devel/arch/sh/include/asm/io.h:163: error: previous definition of 'writesb' was here
Cc: Karsten Keil <kkeil@suse.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While making some other changes to ti_usb_3410_5052, I noticed that the
changes made to move the firmware loading to a separate function are
broken (in ti_download_firmware(), status is set to -ENOMEM and never
changed). This means the driver will never initialize the device
properly. It looks like status was supposed to get the result of
ti_do_download().
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes:
drivers/usb/gadget/fsl_usb2_udc.c: In function 'dr_controller_setup':
drivers/usb/gadget/fsl_usb2_udc.c:229: warning: format '%p' expects type
'void *', but argument 3 has type 'int'
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1136) adds an unusual_devs entry for a version of the
RockChip MP3 player which can't handle the MODE SENSE command used for
write-protect detection.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This hardware needs the pl2303 hack in order to work properly :(
Signed-off-by: Andreas Bombe <aeb@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As noted by Stefan Neis <Stefan.Neis@kobil.com>, we had a recent
regression with EHCI periodic transfers, in some (seemingly not
all that common) cases.
The root cause was that the schedule activation was only loosely
coupled to the addition or removal of transfers, so two different
execution contexts could both think they had to deactivate (or
conversely activate) the schedule. So this fix tightens that
coupling, managing it more like a refcount.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I had trouble connecting my cell phone as a storage device - so I added
it to the unusual_devs.h list. I had trouble with the bcdDeviceMin and
Max values - so after some experimenting I made it pretty inclusive.
From: Filip Joelsson <filip@blueturtle.nu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This resolves another regression caused by the "use omap_read/write
instead of __REG" patch: the hardware address used for DMA to/from
the UDC became wrong. Bug noted by Russell King.
Reported-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit de85422b94, 'USB: fix interrupt
disabling for HCDs with shared interrupt handlers' changed usb_add_hcd()
to strip IRQF_DISABLED from irqflags prior to calling request_irq()
with the justification that such a removal was necessary for shared
interrupts to work properly. Unfortunately, the change in that commit
unconditionally removes the IRQF_DISABLED flag, causing problems on
platforms that don't use a shared interrupt but require IRQF_DISABLED.
This change adds a check for IRQF_SHARED prior to removing the
IRQF_DISABLED flag.
Fixes the PS3 system startup hang reported with recent Fedora and
OpenSUSE kernels.
Note that this problem is hidden when CONFIG_LOCKDEP=y (ps3_defconfig),
as local_irq_enable_in_hardirq() is defined as a null statement for
that config.
CC: stable <stable@kernel.org>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Stefan Becker <Stefan.Becker@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I was trying to figure out why my device wasn't supported by the
drivers/usb/serial/sierra.c driver, while looking throught the device
IDs I spotted what I believe to be a typo in the device IDs. Please
apply the following patch
If you look down further, there is another HP wireless broadband card,
which has a vendor ID of 03f0, like my device. Below is my "lsusb -v
-d 03f0:1b1d".
Bus 001 Device 005: ID 03f0:1b1d Hewlett-Packard
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x03f0 Hewlett-Packard
idProduct 0x1b1d
bcdDevice 0.01
iManufacturer 1 HP
iProduct 2 HP ev2200 1xEV-DO Broadband Wireless Module
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 67
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 7
bInterfaceClass 255 Vendor Specific Class
bInterfaceSubClass 255 Vendor Specific Subclass
bInterfaceProtocol 255 Vendor Specific Protocol
iInterface 3 Data Interface
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0010 1x 16 bytes
bInterval 128
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x84 EP 4 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x04 EP 4 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x85 EP 5 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x05 EP 5 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0040 1x 64 bytes
bInterval 0
Device Status: 0x0000
(Bus Powered)
From: Tony Murray <murraytony@gmail.com>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I noticed that the "Refactor "if (handshake()) state = HC_STATE_HALT"
patch from earlier this year perpetuated a potential problem: it can
mark the controller as halted when it's still running (but not acting
as, perhaps wrongly, expected).
That caused some hangs and crashes, rather than more polite failure
modes of a truly halted controller. This patch forces a true halt,
and emits a (previously missing) diagnostic.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds devices to the sierra driver and rev's the driver version.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch alters the Sierra Mass Storage patch so that it is non-configurable.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The UWB stack has some sysfs APIs that will change thus it's best
marked as EXPERIMENTAL until these APIs are finalized.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Simplify the sysfs ABI of the wusb-cbaf (Cable Based Association)
driver: use one value per file and cause the write of the CHID to
fetch the CDID (instead of requiring a separate read).
Update the example wusb-cbaf script to work with this revised ABI.
Signed-off-by: Felipe Zimmerle <felipe.zimmerle@indt.org.br>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Add a facility for PALs to have symlinks to their radio controller
(and vice-versa) and make WUSB host controllers use this.
Signed-off-by: David Vrabel <david.vrabel@csr.com>
WUSB 1.0 (Table 8-4) mentions that Abort RPipe requests must have bmRequestType
equal to 0x25, although current implementation sets bmRequestType to 0xa5. This
patch fixes this typo.
Signed-off-by: Anderson Lizardo <anderson.lizardo@indt.org.br>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Error path for wusb_set_dev_addr() was handled incorrectly. Fix it by
considering error only when return value is negative.
Signed-off-by: Anderson Lizardo <anderson.lizardo@indt.org.br>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
A driver for Wireless USB host controllers that comply with the
Wireless Host Controller Interface (HCI) specification as published by
Intel.
The latest publically available version of the specification (0.95) is
supported (except for isochronous transfers).
Build fixes by Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Add the WUSB build system (Kconfig and Kbuild) files.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
Add support for Ceritified Wireless USB 1.0 to the USB stack.
This has been split into several patches for easier review.
core (this patch):
- host controller infrastructure
- cluster reservation
- UWB PAL registration
- fake root hub
protocol:
- MMC management (start/stop, managing IEs)
- device connection
security:
- device authentication and authorization
build-system:
- Kconfig and Kbuild files
Signed-off-by: David Vrabel <david.vrabel@csr.com>
The hw interface drivers for the usb serial devices deference the tty
structure to set up the parameters for the initial console. The tty
structure should be passed as a parameter to the set_termios() call.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/usb/host/ohci-omap.c: In function 'ohci_omap_init':
drivers/usb/host/ohci-omap.c:228: error: 'start_hnp' undeclared (first use in this function)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By now, ioaddr_t should only be used by the deprecated ioctl, as it does not
correctly reflect the maximum ioport range at least on some architectures.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
This patch lets the files using linux/version.h match the files that
#include it.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
By passing the current Vcc setting to the pcmcia_config_loop callback
function, we can remove pcmcia_get_configuration_info() calls from many
drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Many drivers use the default CIS entry within their pcmcia_config_loop()
callback function. Therefore, factor the default CIS entry handling out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Almost all drivers set p_dev->conf.ConfigIndex to cfg->index in
the pcmcia_config_loop() callback function. Therefore, factor it out.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Use the config loop helper in misc pcmcia drivers.
CC: Harald Welte <laforge@gnumonks.org>
CC: <linux-parport@lists.infradead.org>
CC: Russell King <rmk+kernel@arm.linux.org.uk>
CC: Ed Okerson <eokerson@quicknet.net>
CC: linux-serial@vger.kernel.org
CC: boti@rocketmail.com
CC: linux-usb@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
sisusbvga: add USB ID for 0711:0918 Magic Control Technology Corp.
usb 1-2: new high speed USB device using ehci_hcd and address 4
usb 1-2: configuration #1 chosen from 1 choice
usb 1-2: USB2VGA dongle found at address 4
usb 1-2: Allocated 8 output buffers
usb 1-2: 8MB 1 ch/1 r SDR SDRAM, bus width 32
usb 1-2: New USB device found, idVendor=0711, idProduct=0918
usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Signed-off-by: Stefan Lippers-Hollmann <s.L-H@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1069c) changes the way OHCI root-hub status-change
interrupts are enabled. Currently a special HCD method,
hub_irq_enable(), is called when the hub driver is finished using a
root hub. This approach turns out to be subject to races, resulting
in unnecessary polling.
The patch does away with the method entirely. Instead, the driver
automatically enables the RHSC interrupt when no more status changes
are present. This scheme is safe with controllers using
level-triggered semantics for their interrupt flags.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1130) fixes an incompatibility between the new PM
infrastructure and USB power management. We are not allowed to call
drivers' probe routines during a system sleep transition between the
"prepare" and "complete" callbacks, but that's exactly what we do when
a driver doesn't have full suspend/resume support. Such drivers are
unbound during the "suspend" call and reprobed during the "resume" call.
The patch causes the reprobe step to be skipped if the "complete"
callback hasn't been issued yet, i.e., if the interface's
dev.power.status field is not equal to DPM_ON. Thus during the
"resume" callback nothing bad will happen, and during the final
"complete" callback the reprobing will occur as desired.
This fixes the problem reported in Bugzilla #11263.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1129) adds support for the new PM callbacks to usbcore.
The new callbacks merely invoke the same old USB power management
routines as the old ones did.
A minor improvement is that the callbacks are present only in the
"USB-device" device_type structure, rather than in the bus_type
structure. This way they will be invoked only for USB devices, not
for USB interfaces. The core USB PM routines automatically handle
suspending and resuming interfaces along with their devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1128) fixes one of the problems related to the new PM
infrastructure. We are not allowed to register new child devices
during the middle of a system sleep transition, but unbinding a USB
driver causes the core to automatically install altsetting 0 and
thereby create new endpoint pseudo-devices.
The patch fixes this problem (and the related problem that installing
altsetting 0 will fail if the device is suspended) by deferring the
Set-Interface call until some later time when it is legal and can
succeed. Possible later times are: when a new driver is being probed
for the interface, and when the interface is being resumed.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1127) makes a minor change to the prototypes of the
usb_suspend_interface() and usb_resume_interface() routines. Now the
usb_device structure is passed as an argument, instead of being
computed on-the-fly from the usb_interface argument.
It makes the code look simpler, even if it really isn't much different
from before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If Indexed Mode register accesses are enabled, the ep0_rxstate()
function calls musb_g_ep0_giveback() before writing to the CSR
register. When control returns to this ep0_rxstate, the index
register contents are over-written. This causes the CSR register
write to fail.
Fixed by writing the correct value into the index register before
writing to the CSR.
This was observed only in ep0_rxstate() with g_ether loaded and
the device connected to a MS Windows host PC. Anticipatively fixed
ep0_txstate() as well.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can change debugging level on the fly via
/sys/module/musb_hdrc/parameters/debug.
We can also get rid of the LOGLEVEL facility in Kconfig
and rely only in module parameter.
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers should not add procfs. The functionality in the old
procfs file will be moved to debugfs.
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The new composite framework revealed a weakness in the
pxa27x_udc driver gadget register function. Instead of
checking if speed asked for was USB_LOW_SPEED upon
usb_gadget_register() to deny service, it checked only
for USB_FULL_SPEED, thus denying service to usb high
speed capable gadgets (like g_ether).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch gets my Rosewill RNX-56USB USB modem (with Conexant CX93010
chipset) up and running to the point where I can send AT commands and
retrieve caller ID data, which is all I want to do with it.
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Irqs must not accidentally be reenabled.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch support NTT DoCoMo A2502 3G/HSDPA modem on option driver.
It is produced by AnyDATA Corp. and also sold as KT Freetelecom (Korea) ADU 620UW.
It support 3.6Mbps/7.2Mbps hight speed communication.
I have tested A2502 with NTT DoCoMo MoperaU ISP service.
Signed-off-by: Hiroshi Miura <miurahr@nttdata.co.jp>
Signed-off-by: Matthias Urlichs <matthias@urlichs.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/home/rmk/linux-2.6-arm: (38 commits)
[ARM] 5191/1: ARM: remove CVS keywords
[ARM] pxafb: fix the warning of incorrect lccr when lcd_conn is specified
[ARM] pxafb: add flag to specify output format on LDD pins when base is RGBT16
[ARM] pxafb: fix the incorrect configuration of GPIO77 as ACBIAS for TFT LCD
[ARM] 5198/1: PalmTX: PCMCIA fixes
[ARM] Fix a pile of broken watchdog drivers
[ARM] update mach-types
[ARM] 5196/1: fix inline asm constraints for preload
[ARM] 5194/1: update .gitignore
[ARM] add proc-macros.S include to proc-arm940 and proc-arm946
[ARM] 5192/1: ARM TLB: add v7wbi_{possible,always}_flags to {possible,always}_tlb_flags
[ARM] 5193/1: Wire up missing syscalls
[ARM] traps: don't call undef hook functions with spinlock held
[ARM] 5183/2: Provide Poodle LoCoMo GPIO names
[ARM] dma-mapping: provide sync_range APIs
[ARM] dma-mapping: improve type-safeness of DMA translations
[ARM] Kirkwood: instantiate the orion_spi driver in the platform code
[ARM] prevent crashing when too much RAM installed
[ARM] Kirkwood: Instantiate mv_xor driver
[ARM] Orion: Instantiate mv_xor driver for 5182
...
Use platform_data to pass musb configuration-specific
details to musb driver.
This patch will prevent that other platforms selecting
HAVE_CLK and enabling musb won't break tree building.
The other parts of it will come when linux-omap merge
up more omap2/3 board-files.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we try to modprobe a second gadget driver before
rmmoding the first one, the reference for the first
gadget driver would get NULLed avoiding usb to change
gadget drivers later.
Cc: David Brownell <david-b@pacbell.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These drivers should not be relying on CONFIG_USB_DEBUG. By doing this,
it prevents users of kernels that do not enable this option from
enabling debugging in these drivers, unlike all other usb-serial
drivers.
Cc: Matthias Urlichs <smurf@smurf.noris.de>
Cc: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the vendor and product id (19d2:0015) of the ZTE MF628 HSDPA
modem to the option driver. It still needs a mode switch command issued
beforehand, this is currently handled by a userspace tool.
Signed-off-by: Oliver Martin <oliver.martin@student.tuwien.ac.at>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On some AMD 700 series southbridges, ISO OUT transfers (such as audio
playback through speakers) on the USB OHCI controller may be corrupted
when an A-Link express power saving feature is active.
PLL power down mode in conjunction with link power management feature
L1 being enabled is the bad combination ... this patch prevents them
from being enabled when ISO transfers are pending.
Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a mechanism to let the write queue drain naturally before
closing the TTY, rather than always losing that data. There
is a timeout, so it can't wait too long.
Provide missing locking inside acm_wb_is_avail(); it matters
more now. Note, this presumes an earlier patch was applied,
removing a call to this routine where the lock was held.
Slightly improved diagnostics on write URB completion, so we
can tell when a write URB gets killed and, if so, how much
data it wrote first ... and so that I/O path is normally
silent (and can't much change timings).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "increase cdc-acm write throughput" patch left in place two
now-obsolete mechanisms, either of which can make the cdc-acm
driver drop TX data (nasty!). This patch removes them:
- The write_ready flag ... if an URB and buffer were found,
they can (and should!) always be used.
- TX path acm_wb_is_used() ... used when the buffer was just
allocated, so that check is pointless.
Also fix a won't-yet-matter leak of a write buffer on a disconnect path.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Engraf <david.engraf@netcom.eu>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Bugfixes to the usb_driver_release_interface() usage;
(a) make sure releasing *either* interface first will release
the other, instead of insisting it be the control interface;
(b) remove the recently-added self-deadlock.
(The "fix disconnect bug in cdc-acm" patch was incomplete and incorrect.)
Plus a small "sparse" fix: rename a local variable so it doesn't
shadow a function parameter.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the CDC-ACM gadget code to support the peripheral-to-host
notifications when the tty is opened or closed, or issues a BREAK.
The serial framework code calls new generic hooks; right now only
CDC-ACM uses those hooks. This resolves several REVISIT comments
in the code. (Based on a patch from Felipe Balbi.)
Note that this doesn't expose USB_CDC_CAP_BRK to the host, since
this code still rejects USB_CDC_REQ_SEND_BREAK control requests
for host-to-peripheral BREAK signaling (received via /dev/ttyGS*).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes some unused members from the various USB functions.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the regression in commit 29fab0cd89
that this driver executed reconnection processing when disconnected
some devices.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1123b) fixes a compiler warning: do_unbind_rebind() is
defined but not used if CONFIG_PM=n.
Problem originally found and initial patch submitted by Alexander
Beregalov <a.beregalov@gmail.com>.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1120) adds an unusual_devs entry for the Nokia 5300.
Maybe once Nokia releases the Symbian code we'll be able to fix all
the problems it has with the USB mass-storage protocol.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Cedric Godin <cedric@belbone.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The irq flags should be unsigned long.
CC [M] drivers/usb/class/cdc-acm.o
drivers/usb/class/cdc-acm.c: In function 'acm_waker':
drivers/usb/class/cdc-acm.c:527: warning: comparison of distinct pointer types lacks a cast
drivers/usb/class/cdc-acm.c:529: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the Product ID for the BandLuxe C150/C250 3.5G data
card series from BandRich Inc.
After detection, the data card works fine.
It was patched against kernel 2.6.27-rc1 with -mm patch
Signed-off-by: Leon Leong <upleong@bandrich.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Support for PHI Fisco USB to Serial data cable (FTDI FT232BM based).
PHI Fisco cable is supplied for connecting Philips Xenium 9@9++ mobile phones.
PIDs were missing.
Tested successfully with PHI Fisco Data Cable (VID/PID 0403:e40b)
Signed-off-by: Lex V. Ross <lross@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to Alan Stern, short packets are quite normal under
certain circumstances. This printk was triggered by usb to
serial converters on every packet and some usb sticks triggered
a few of those while plugging the stick.
This printks are now hidden unless USB debug mode is activated.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
ISP1760 requires a delay of 90ns between programming the address and
reading the data. Current driver solves this by a mdelay(1) which is
very heavy weighted and slow. This patch applies the workaround from
the ISP1760 FAQ by using two different banks for PTD and payload data
and using a common wait for them. This wait is done by an additional
ISP1760 access (whose timing constraints guarantee the 90ns delay).
This improves speed when reading from an USB stick from:
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 1m 15.43s
user 0m 0.44s
sys 0m 39.46s
to
$ time dd if=/dev/sda of=/dev/zero bs=65536 count=1638
real 0m 18.53s
user 0m 0.16s
sys 0m 12.97s
[bigeasy@linutronix.de: fixed comment formating, moved define into
header file, obey 80 char rule]
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
if the enqueue function returns -ESHUTDOWN or -ENOMEM then
we return 0 instead of an error. This leads to a timeout and
then to a dequeue request of an not enqueued urb.
Signed-off-by: Sebastian Siewior <sebastian@breakpoint.cc>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update RX path handling in new serial gadget code to cope better with
RX blockage: queue every RX packet until its contents can safely be
passed up to the ldisc. Most of the RX path work is now done in the
RX tasklet, instead of just the final "push to ldisc" step. This
addresses some cases of data loss:
- A longstanding serial gadget bug: when tty_insert_flip_string()
didn't copy the entire buffer, the rest of the characters were
dropped! Now that packet stays queued until the rest of its data
is pushed to the ldisc.
- Another longstanding issue: in the unlikely case that an RX
transfer returns data and also reports a fault, that data is
no longer discarded.
- In the recently added RX throttling logic: it needs to stop
pushing data into the TTY layer, instead of just not submitting
new USB read requests. When the TTY is throttled long enough,
backpressure will eventually make the OUT endpoint NAK.
Also: an #ifdef is removed (no longer necessary); and start switching
to a better convention for debug messages (prefix them with tty name).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
add razr v3xx US_FL_FIX_CAPACITY flag to unusual_devs.h in usb-storage
This is another Motorola phone that incorrectly reports the sector count
(off by one).
Problem Description: io errors when mounting phone's sd-card via the
phones usb port
Steps to reproduce: mount Motorola Razr v3xx phones sd-card on Linux Desktop
via usb cable. Phones USB port must be in memory card mode.
DEBUG output:
Jul 9 19:32:41 micky kernel: Buffer I/O error on device sdd, logical block 3970048
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Sense Key : Medium Error [current]
Jul 9 19:32:41 micky kernel: sd 11:0:0:0: [sdd] Add. Sense: No additional sense information
Jul 9 19:32:41 micky kernel: end_request: I/O error, dev sdd, sector 3970048
From: Jost Diederichs <jost@qdusa.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch upgrades the support for the Sierra Wireless TRU-Install
feature (i.e. zeroCD) to allow for future support of Linux enabled
TRU-Install devices.
By default all devices that do not have a Linux enabled TRU-Install
device (i.e. the device does not have a Linux package on the virtual CD
partition) will be switched into "modem mode." Devices that do contain a
Linux package in the TRU-Install virtual CD will be allowed to enumerate
as a CD-Rom so that either (a) a user can install the packaged software
or (b) a user-space application (e.g. udev) can switch it to modem mode.
This patch does allow for manual override by adding a usb-storage module
parameter 'swi_tru_install' which can force the modem into either mode
regardless of what packages it contains.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Moves responsbility of TRU-Install (i.e. ZeroCD) to the usb-storage
driver. See patch 04/04 of this set.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch changes the method by which the number of ports per interface is
assigned so that it is more dynamic and calculated on the fly (as opposed to
hard coding it). This will allow for faster and easier addition of products.
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Very minor changes to clean up sierra code. Adds a prefix to debug messages so
that Sierra messages are easily recognized. Removes extraneous code.
This targets kernel 2.6.26-rc9
Signed-off-by: Kevin Lloyd <klloyd@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB ID 4348:5523 is handled by the ch341 driver. Remove it from the
pl2023 driver.
Reverts 002e8f2c80.
Signed-off-by: Tollef Fog Heen <tfheen@err.no>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1115) adds unusual_devs entries with the IGNORE_RESIDE
flag for the iRiver T10 and the Simple Tech/Datafab CF+SM card
reader. Apparently these devices provide reasonable residue values
for READ and WRITE operations, but not for others like INQUIRY or READ
CAPACITY.
This fixes the iRiver T10 problem reported in Bugzilla #11125.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes "USB Monitor" appear under "Miscellaneous USB options"
section instead of in the middle of device specific drivers in the
"USB Imaging devices" section.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1119) will help to reduce the clutter of usb-storage's
unusual_devs file by automatically detecting some devices that need
the IGNORE_RESIDUE flag. The idea is that devices should never return
a non-zero residue for an INQUIRY or a READ CAPACITY command unless
they failed to transfer all the requested data. So if one of these
commands transfers a standard amount of data but there is a positive
residue, we know that the residue is bogus and we can set the flag.
This fixes the problems reported in Bugzilla #11125.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1122) fixes a bug: When an interface is unregistered,
its children (sysfs files and endpoint devices) are unregistered after
it instead of before.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1121) fixes a bug in the USB serial core. When a device
is unregistered, the core will give back its minors -- even if the
device hasn't been assigned any!
The patch reserves the highest minor value (255) to mean that no minor
was assigned. It also removes some dead code and does a small style
fixup.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Without it, we might have trouble when trying to write
some composite gadget drivers.
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb-storage: quirk around v1.11 firmware on Nikon D40
https://bugzilla.redhat.com/show_bug.cgi?id=454028
Just as in earlier firmware versions, we need to perform this
quirk for the latest version too.
Speculatively do the entry for the D80 too, as they seem to
have the same firmware problems historically.
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1114) fixes a problem that was revealed by an earlier
patch (as1069b). Some broken controllers seem never to turn off their
RHCS interrupt status bit, even when told to do so. As a result they
generate an interrupt storm and hang the system.
The patch avoids enabling RHSC interrupt requests when the RHCS status
bit is already set. This should have no adverse affects on normal
controllers, since they won't set the status bit until a root-hub
status change actually occurs, in which case we wouldn't enable RHSC
interrupt requests anyway -- we would wait until the status change had
been processed and cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb/core/driver: fix warning:
drivers/usb/core/driver.c:834: warning: 'do_unbind_rebind' defined but not used
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Patch adds support for Luminance Stellaris Evaluation/Development
Kits (FTDI 2232C based).
The PIDs were missing.
Successfully tested with a Stellaris LM3S8962 Evaluation kit.
Signed-off-by: Frederik Kriewitz <frederik@kriewitz.eu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB product id registration for the ELV HS485 USB adapter (www.elv.de) to
their home automation bus system. Applies to 2.6.26.
Signed-off-by: Andre Schenk <andre@melior.s.bawue.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a BUG() turned up by Ingo via randconfig testing, where
CONFIG_LIST_DEBUG turned up list corruption. The corruption was
caused by the dummy_hcd (single-machine test harness for gadget and
HCD code) trashing the request queue when driven by the new CDC
composite gadget an I/O pattern that was previously uncommon.
Fix suggested by Alan Stern.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the auerswald USB driver from the linux kernel
2.6.26.
This driver was included into the kernel mainly to connect to the ISDN
framework. This was done in linux 2.4.x. For 2.6.x, due to the fragile
and moving ISDN support, this connection was never realized, and the
only use of this driver was for device configuration. In the age of DSL,
the demand of ISDN support is getting very low.
Meanwhile, with the advent of libusb, an userspace driver was done for
the device configuration which works fine for linux and mac. (Thanks to
the libusb developers!). The userspace driver is downloadable from the
auerswald web site.
So this driver is obsolete now and has to be removed. Many thanks to all
developers which helped me to bring this driver up and working.
Signed-off-by: Wolfgang Muees <wolfgang@iksw-muees.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
* 'for-linus-merged' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 5177/1: arm/mach-sa1100/Makefile: remove CONFIG_SA1100_USB
[ARM] 5166/1: magician: add MAINTAINERS entry
[ARM] fix pnx4008 build errors
[ARM] Fix SMP booting with non-zero PHYS_OFFSET
[ARM] 5185/1: Fix spi num_chipselect for lubbock
[ARM] Move include/asm-arm/arch-* to arch/arm/*/include/mach
[ARM] Add support for arch/arm/mach-*/include and arch/arm/plat-*/include
[ARM] Remove asm/hardware.h, use asm/arch/hardware.h instead
[ARM] Eliminate useless includes of asm/mach-types.h
[ARM] Fix circular include dependency with IRQ headers
avr32: Use <mach/foo.h> instead of <asm/arch/foo.h>
avr32: Introduce arch/avr32/mach-*/include/mach
avr32: Move include/asm-avr32 to arch/avr32/include/asm
[ARM] sa1100_wdt: use reset_status to remember watchdog reset status
[ARM] pxa: introduce reset_status and clear_reset_status for driver's usage
[ARM] pxa: introduce reset.h for reset specific header information
If you are using linked lists for queues list_splice() will not do what
you would expect even if you use the elements passed reversed. We need
to handle these differently. We add list_splice_tail() and
list_splice_tail_init().
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There are 43 includes of asm/mach-types.h by files that don't
reference anything from that file. Remove these unnecessary
includes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Okay, I found the cause of the hang. It is a simple bug in the USB
scatter-gather library, caused by changes added in response to the S-G
chaining modification.
This patch (as1125) fixes a bug in the USB scatter-gather library.
Early exit from the S-G initialization loop does not reset the count of
outstanding URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 0031a06e2f converted all of the USB
drivers to use dev_set_name(), though there was a typo on the m66592-udc
conversion that handed off the wrong pointer (we want the struct device
here obviously, not the struct usb_gadget).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The fix NULLed a pointer without freeing it.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Reported-by: Juha Motorsportcom <juha_motorsportcom@luukku.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kmem cache passed to constructor is only needed for constructors that are
themselves multiplexeres. Nobody uses this "feature", nor does anybody uses
passed kmem cache in non-trivial way, so pass only pointer to object.
Non-trivial places are:
arch/powerpc/mm/init_64.c
arch/powerpc/mm/hugetlbpage.c
This is flag day, yes.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Jon Tollefson <kniht@linux.vnet.ibm.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Matt Mackall <mpm@selenic.com>
[akpm@linux-foundation.org: fix arch/powerpc/mm/hugetlbpage.c]
[akpm@linux-foundation.org: fix mm/slab.c]
[akpm@linux-foundation.org: fix ubifs]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
prepare x86: usb debug port early console
move ehci struct def to linux/usrb/ehci_def.h from host/ehci.h
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "Arjan van de Ven" <arjan@infradead.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Greg KH" <greg@kroah.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We want to use WARN() as a variant of WARN_ON(), however a few drivers are
using WARN() internally. This patch renames these to WARNING() to avoid the
namespace clash. A few cases were defining but not using the thing, for those
cases I just deleted the definition.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Greg KH <greg@kroah.com>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (85 commits)
[ARM] pxa: add base support for PXA930 Handheld Platform (aka SAAR)
[ARM] pxa: add base support for PXA930 Evaluation Board (aka TavorEVB)
[ARM] pxa: add base support for PXA930 (aka Tavor-P)
[ARM] Update mach-types
[ARM] pxa: make littleton to use the new smc91x platform data
[ARM] pxa: make zylonite to use the new smc91x platform data
[ARM] pxa: make mainstone to use the new smc91x platform data
[ARM] pxa: make lubbock to use new smc91x platform data
[NET] smc91x: prepare SMC_USE_PXA_DMA to be specified in platform data
[NET] smc91x: prepare for SMC_IO_SHIFT to be a platform configurable variable
[NET] smc91x: add SMC91X_NOWAIT flag to platform data
[NET] smc91x: favor the use of SMC91X_USE_* instead of SMC_CAN_USE_*
[NET] smc91x: remove "irq_flags" from "struct smc91x_platdata"
[ARM] 5146/1: pxa2xx: convert all boards to call pxa2xx_transceiver_mode helper
Support for LCD on e740 e750 e400 and e800 e-series PDAs
E-series UDC support
PXA UDC - allow use of inverted GPIO for pullup
Add e350 support
Fix broken e-series build
E-series GPIO / IRQ definitions.
...
Stephen Rothwell points out that this file got deleted (on purpose) by
commit 640c1bce86 ("USB: delete airprime
driver"), but then almost immediately incorrectly resurrected by commit
95da310e66 ("usb_serial: API all change").
Delete it again. If it comes back, we'll need to drive a stake through
its heart.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6: (79 commits)
arm: bus_id -> dev_name() and dev_set_name() conversions
sparc64: fix up bus_id changes in sparc core code
3c59x: handle pci_name() being const
MTD: handle pci_name() being const
HP iLO driver
sysdev: Convert the x86 mce tolerant sysdev attribute to generic attribute
sysdev: Add utility functions for simple int/ulong variable sysdev attributes
sysdev: Pass the attribute to the low level sysdev show/store function
driver core: Suppress sysfs warnings for device_rename().
kobject: Transmit return value of call_usermodehelper() to caller
sysfs-rules.txt: reword API stability statement
debugfs: Implement debugfs_remove_recursive()
HOWTO: change email addresses of James in HOWTO
always enable FW_LOADER unless EMBEDDED=y
uio-howto.tmpl: use unique output names
uio-howto.tmpl: use standard copyright/legal markings
sysfs: don't call notify_change
sysdev: fix debugging statements in registration code.
kobject: should use kobject_put() in kset-example
kobject: reorder kobject to save space on 64 bit builds
...
Some hardware needs to do break handling itself and may have partial
support only. Make break_ctl return an error code. Add a tty driver flag
so you can indicate driver hardware side break support.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The edgeport reports negative error codes to functions that do not
expect them. This can cause ports to jam forever
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Setting CFLAG bits is all well and good but you must sort out ispeed and
ospeed properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bring ezusb and whiteheat into line with the coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
USB serial likes to use port->tty back pointers for the real work it does and
to do so without any actual locking. Unfortunately when you consider hangup
events, hangup/parallel reopen or even worse hangup followed by parallel close
events the tty->port and port->tty pointers are not guaranteed to be the same
as port->tty is the active tty while tty->port is the port the tty may or
may not still be attached to.
So rework the entire API to pass the tty struct. For console cases we need
to pass both for now. This shows up multiple drivers that immediately crash
with USB console some of which have been fixed in the process.
Longer term we need a proper tty as console abstraction
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Why?:
There are occasions where userspace would like to access sysfs
attributes for a device but it may not know how sysfs has named the
device or the path. For example what is the sysfs path for
/dev/disk/by-id/ata-ST3160827AS_5MT004CK? With this change a call to
stat(2) returns the major:minor then userspace can see that
/sys/dev/block/8:32 links to /sys/block/sdc.
What are the alternatives?:
1/ Add an ioctl to return the path: Doable, but sysfs is meant to reduce
the need to proliferate ioctl interfaces into the kernel, so this
seems counter productive.
2/ Use udev to create these symlinks: Also doable, but it adds a
udev dependency to utilities that might be running in a limited
environment like an initramfs.
3/ Do a full-tree search of sysfs.
[kay.sievers@vrfy.org: fix duplicate registrations]
[kay.sievers@vrfy.org: cleanup suggestions]
Cc: Neil Brown <neilb@suse.de>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Reviewed-by: SL Baur <steve@xemacs.org>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Acked-by: Mark Lord <lkml@rtr.ca>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1110) reverts an earlier patch meant to help with
Wireless USB host controllers. These controllers can have bulk
maxpacket values larger than 512, which puts unusual constraints on
the sizes of scatter-gather list elements. However it turns out that
the block layer does not provide the support we need to enforce these
constraints; merely changing the DMA alignment mask doesn't help.
Hence there's no reason to keep the original patch. The Wireless USB
problem will have to be solved a different way.
In addition, there is a reason to get rid of the earlier patch. By
dereferencing a pointer stored in the ep_in array of struct
usb_device, the current code risks an invalid memory access when it
runs concurrently with device removal. The members of that array are
cleared before the driver's disconnect method is called, so it should
not try to use them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1109b) makes USB-Persist more resilient to errors. With
the current code, if a normal resume fails, it's an unrecoverable
error. With the patch, if a normal resume fails (and if the device is
enabled for USB-Persist) then a reset-resume is tried.
This fixes the problem reported in Bugzilla #10977.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These two fixes ensure the new "CDC Composite Device" gadget
fails cleanly when it's loaded on hardware that can't support
this particular gadget driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fill in a reserved/unused device qualifier field to ensure that
the USBCV tests will always pass.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
URB payload data are transfered in wrong byte order on a big endinan
architecture (AVR32).
Signed-off-by: Julien May <mailinglist@miromico.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in the error case the ipaq driver leaves a dangling pointer to already
freed memory that will be freed again.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here's the fix. cdc-wdm has the same problem. The fix is the same.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove the board-specific UP2OCR configuration from the
pxa27x-udc driver.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A couple of USB register initializations had to be changed on MPC85xx
platforms. This is due to the internal SoC buses being different on
MPC83xx SoCs vs MPC85xx SoCs.
We currently handle this via an ifdef since 83xx and 85xx are mutually
exclusive kernel builds.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix pointer/int cast in USB devio code, and thus avoid a compiler warning.
A void* data argument passed to bus_find_device() and thence to match_devt()
is used to carry a 32-bit datum. However, casting directly between a u32 and
a pointer is not permitted - there must be an intermediate cast via (unsigned)
long.
This was introduced by the following patch:
commit 94b1c9fa060ece2c8f080583beb6cc6008e41413
Author: Alan Stern <stern@rowland.harvard.edu>
Date: Tue Jun 24 14:47:12 2008 -0400
usbfs: simplify the lookup-by-minor routines
This patch (as1105) simplifies the lookup-by-minor-number code in
usbfs. Instead of passing the minor number to the callback, which
must then reconstruct the entire dev_t value, the patch passes the
dev_t value directly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Copy the OHCI/EHCI PM callbacks of the PCI implementation since
they work equally well on Au1xxx hardware.
Tested on Au1200.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Fold multiple probe/remove callbacks into one function;
- minor style fixes, no functional changes.
Tested on Au1200.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1107) fixes a small bug in the usbfs registration and
unregistration code. It avoids leaving an error value stored in the
device's usb_classdev field and it avoids trying to unregister a NULL
pointer. (It also fixes a rather extreme overuse of whitespace.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1106) fixes a race between opening and unregistering
device files in usbfs. The current code drops its reference to the
device and then reacquires it, ignoring the possibility that the
device structure might have been removed in the meantime. It also
doesn't check whether the device is already in the NOTATTACHED state
when the file is opened.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1105) simplifies the lookup-by-minor-number code in
usbfs. Instead of passing the minor number to the callback, which
must then reconstruct the entire dev_t value, the patch passes the
dev_t value directly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB device files are accessible in two ways: as files in usbfs and as
character device nodes. The two paths are supposed to behave
identically, but they don't. When the underlying USB device is
unplugged, disconnect signals are sent to processes with open usbfs
files (if they requested these signals) but not to processes with open
device node files.
This patch (as1104) fixes the bug by moving the disconnect-signalling
code into a common subroutine which is called from both paths.
Putting this subroutine in devio.c removes the only out-of-file
reference to struct dev_state, and so the structure's declaration can
be moved from usb.h into devio.c.
Finally, the new subroutine performs one extra action: It kills all
the outstanding async URBs. (I'd kill the outstanding synchronous
URBs too, if there was any way to do it.) In the past this hasn't
mattered much, because devices were unregistered from usbfs only
when they were disconnected. But now the unregistration can also
occur whenever devices are unbound from the usb_generic driver. At
any rate, killing URBs when a device is unregistered from usbfs seems
like a good thing to do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1024) takes care of a FIXME issue: Drivers that don't
have the necessary suspend, resume, reset_resume, pre_reset, or
post_reset methods will be unbound and their interface reprobed when
one of the unsupported events occurs.
This is made slightly more difficult by the fact that bind operations
won't work during a system sleep transition. So instead the code has
to defer the operation until the transition ends.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various cleanups and fixes to the i2c code in ohci-pnx4008:
* Delete empty isp1301_command. The i2c driver command implementation
is optional, so there's no point in providing an empty
implementation.
* Give a name to isp1301_driver. I'm surprised that i2c-core accepted
to register this driver at all. I've chosen "isp1301_pnx" as the
name, because it's not a generic ISP1301 driver (much like the
isp1301_omap driver.) We might want to make the name even more
specific (but "isp1301_ohci_pnx4008" doesn't fit.)
* The ISP1301 is definitely not a hardware monitoring device.
* Fix a memory leak on failure in isp1301_attach. If
i2c_attach_client fails, the client is not registered so
isp1301_detach is never called and the i2c_client memory is lost.
* Use strlcpy instead of strcpy.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB debug port only supports 8 byte rx/tx packets. Although spec implies that
"if a packet larger than eight bytes is received from the remote computer, the
device must break the larger packet into eight-byte packets before sending the
data to the Debug Port", the real PLX NET20DC device does not handle it right -
data is corrupted on debug port end if serial interface sends >8 byte urbs.
Patch below fixes the issue by limiting tx urb to 8 byte.
Signed off by: Aleks Gorelov <dared1st@yahoo.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
cdc-acm must give up secondary interfaces if the primary is disconnected
and vice versa. This wasn't done correctly.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb serial decrements the pm counter even if an interface has been
disconnected. If it was a logical disconnect the interface may belong
already to another driver. This patch introduces a check for disconnected
interfaces.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch saves power for cdc-acm devices that support remote wakeup
while the device is connected.
- request needs_remote_wakeup when needed
- delayed write while a device is autoresumed
- the device is marked busy when appropriate
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 28xb, as documented in comments, has the same ID's as the 28x.
Remove the duplicated ID's from the device tables, and expand the
comment to document this.
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix the problem that did not set IRQF_TRIGGER_ flag.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
