Just as commit "net: macb: DMA-unmap full rx-buffer"
(48330e08fa), pass the size that
was used for mapping the memory also to the unmap routine to
avoid warnings from the DMA_API.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip_tunnel_rcv(), set skb->network_header to inner IP header
before IP_ECN_decapsulate().
Without the fix, IP_ECN_decapsulate() takes outer IP header as
inner IP header, possibly causing error messages or packet drops.
Note that this skb_reset_network_header() call was in this spot when
the original feature for checking consistency of ECN bits through
tunnels was added in eccc1bb8d4 ("tunnel: drop packet if ECN present
with not-ECT"). It was only removed from this spot in 3d7b46cd20
("ip_tunnel: push generic protocol handling to ip_tunnel module.").
Fixes: 3d7b46cd20 ("ip_tunnel: push generic protocol handling to ip_tunnel module.")
Reported-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Ying Cai <ycai@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000e only.
David provides four fixes for e1000e, first is a workaround for a hardware
erratum on 82579 devices which experienced packet loss in gigabit and 100
speeds when interconnect between the PHY and MAC is exiting K1 power saving
state. Second expands the scope of a workaround to include i217 and i218
parts as well to address over aggressive transmit behavior when connecting
at 10Mbs half-duplex. Next is to resolve a reported link flap issue on
82579 parts which was root caused as an interoperability problem between
82579 and at least some Broadcom PHYs in the Energy Efficient Ethernet wake
mechanism. Lastly, restricts the workaround of putting the PHY into MDIO
slow mode to access the PHY id to relevant parts since this issue has been
fixed on the newer hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It has been determined that the workaround of putting the PHY into MDIO
slow mode to access the PHY id is not necessary with Lynx Point and newer
parts. The issue that necessitated the workaround has been fixed on the
newer hardware.
We will maintains, as a last ditch attempt, the conversion to MDIO Slow
Mode in the failure branch when attempting to access the PHY id so as to
cover all contingencies.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several customers have reported a link flap issue on 82579. The symptoms
are random and intermittent link losses when 82579 is connected to specific
link partners. Issue has been root caused as interoperability problem
between 82579 and at least some Broadcom PHYs in the Energy Efficient
Ethernet wake mechanism.
To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
Low Power Idle. This solution will cause an increase of power in 100M EEE
link. It will cost additional 28mW in this specific mode.
Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In commit 772d05c51c "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.
This same behavior is seen on i217 and i218 parts as well. This patch expands
the original workaround to encompass these parts.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is a workaround for a HW erratum on 82579 devices.
Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset
specification Update June 2013.
Problem: 82579 parts experience packet loss in Gig and 100 speeds
when interconnect between PHY and MAC is exiting K1 power saving state.
This was previously believed to only affect 1Gig speed, but has been observed
at 100Mbs also.
Workaround: Disable K1 for 82579 devices at Gig and 100 speeds.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Or Gerlitz says:
====================
This series contains fixes for 3.15-rc, mostly around SRIOV. The patches by Jack,
Matan and myself fix few issues related to mlx4 SRIOV support for RoCE and single
port VFs, and the patch from Eyal eliminates checking PCI caps for VFs which is misleading.
Patches done against the net tree, commit 014f1b2 "net: bonding: Fix format string
mismatch in bond_sysfs.c"
We'd be happy to get Eyal's patch queued in your -stable list for 3.14.y
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Carrying out PCI speed/width checks through pcie_get_minimum_link()
on VFs yield wrong results, so remove them.
Fixes: b912b2f ('net/mlx4_core: Warn if device doesn't have enough PCI bandwidth')
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running in SRIOV mode, VM that is assigned with a non-provisioned
Ethernet VFs get themselves a random mac when the Eth driver starts. In
this case, if the IB driver startup code that deals with RoCE runs first,
it will use a zero mac as the source mac for the Para-Virtual CM MADs
which is buggy. To handle that, we change the order of loading.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that deals with computing the slave id based on a given GID
gave wrong results when the number of single port VFs wasn't the
same for port 1 vs. port 2 and the relevant VF is single ported on
port 2. As a result, incoming CM MADs were dispatched to the wrong VF.
Fixed that and added documentation to clarify the computation steps.
Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using single ported VFs and the VF is using port 2, we need
to adjust the port accordingly (change it from 1 to 2).
Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4d619f625a ("net: cdc_ncm: no point in filling up the NTBs
if we send ZLPs") changed the padding logic for devices with the ZLP
flag set. This meant that frames of any size will be sent without
additional padding, except for the single byte added if the size is
a multiple of the USB packet size. But if the unpadded size is
identical to the maximum frame size, and the maximum size is a
multiplum of the USB packet size, then this one-byte padding will
overflow the buffer.
Prevent padding if already at maximum frame size, letting usbnet
transmit a ZLP instead in this case.
Fixes: 4d619f625a ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs")
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `altera_tse_probe':
altera_tse_main.c:(.text+0x25ec2e): undefined reference to `dma_set_mask'
altera_tse_main.c:(.text+0x25ec78): undefined reference to `dma_supported'
altera_tse_main.c:(.text+0x25ecb6): undefined reference to `dma_supported'
drivers/built-in.o: In function `sgdma_async_read':
altera_sgdma.c:(.text+0x25f620): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f678): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f696): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f6f0): undefined reference to `dma_map_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f702): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `sgdma_tx_buffer':
(.text+0x25f92a): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_rx_status':
(.text+0x25fa24): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now the core vsock module is the owner of the proto family. This
means there's nothing preventing the transport module from unloading if
there are open sockets, which results in a panic. Fix that by allowing
the transport to be the owner, which will refcount it properly.
Includes version bump to 1.0.1.0-k
Passes checkpatch this time, I swear...
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-05-01
Please pull the following batch of fixes intended for the 3.15 stream!
For the Bluetooth bits, Gustavo says:
"Some fixes for 3.15. There is a revert for the intel driver, a new
device id, and two important SSP fixes from Johan."
On top of that...
Ben Hutchings gives us a fix for an unbalanced irq enable in an
rtl8192cu error path.
Colin Ian King provides an rtlwifi fix for an uninitialized variable.
Felix Fietkau brings a pair of ath9k fixes, one that corrects a
hardware initialization value and another that removes an (unnecessary)
flag that was being used in a way that led to a software tx queue
hang in ath9k.
Gertjan van Wingerde pushes a MAINTAINERS change to remove himself
from the rt2x00 maintainer team.
Hans de Goede fixes a brcmfmac firmware load hang.
Larry Finger changes rtlwifi to use the correct queue for V0 traffic
on rtl8192se.
Rajkumar Manoharan corrects a race in ath9k driver initialization.
Stanislaw Gruszka fixes an rt2x00 bug in which disabling beaconing
once on USB devices led to permanently disabling beaconing for those
devices.
Tim Harvey provides fixes for a pair of ath9k issues that can lead
to soft lockups in that driver.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
hhf_change() takes the sch_tree_lock and releases it but misses the
error cases. Fix the missed case here.
To reproduce try a command like this,
# tc qdisc change dev p3p2 root hhf quantum 40960 non_hh_weight 300000
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit:
commit 9ec36cafe4
Author: Rob Herring <robh@kernel.org>
Date: Wed Apr 23 17:57:41 2014 -0500
of/irq: do irq resolution in platform_get_irq
changed platform_get_irq() which now returns EINVAL and EPROBE_DEFER,
in addition to ENXIO. If there's no interrupt for mvmdio, platform_get_irq()
returns EINVAL, but we currently check only for ENXIO.
Fix this by looking for a positive integer, which is the proper way of
validating a virtual interrupt number.
While at it, add a proper handling for the deferral probe case.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_state_machine should check whether auto-negotiatin is completed
before changing phydev->state from PHY_NOLINK to PHY_RUNNING. If
auto-negotiation is not completed phydev->state should be set to
PHY_AN.
Signed-off-by: Balakumaran Kannan <kumaran.4353@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do checksum offload only if the client of the driver wants checksum to be
offloaded.
In V1 version of this patch, I addressed comments from
Stephen Hemminger <stephen@networkplumber.org> and
Eric Dumazet <eric.dumazet@gmail.com>.
In this version of the patch I have addressed comments from
David Miller.
This patch fixes a bug that is exposed in gateway scenarios.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For phy devices that don't issue interrupts upon link
state changes, phylib polls the link state resulting in
repeated calls to adjust_link(), even if the link state
didn't change. As a result, some mac registers are
repeatedly read and written with the same values, which
is not ok.
To fix this, adjust_link() has been refactored to check
first whether the link state has changed and to take action
only if needed, updating mac registers and local state
variables. The 'new_state' local flag, set if one of the
link params changed (link, speed or duplex), has been
rendered useless and removed by this refactoring.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit b9f47a3aae (tcp_cubic: limit delayed_ack ratio to prevent
divide error) try to prevent divide error, but there is still a little
chance that delayed_ack can reach zero. In case the param cnt get
negative value, then ratio+cnt would overflow and may happen to be zero.
As a result, min(ratio, ACK_RATIO_LIMIT) will calculate to be zero.
In some old kernels, such as 2.6.32, there is a bug that would
pass negative param, which then ultimately leads to this divide error.
commit 5b35e1e6e9 (tcp: fix tcp_trim_head() to adjust segment count
with skb MSS) fixed the negative param issue. However,
it's safe that we fix the range of delayed_ack as well,
to make sure we do not hit a divide by zero.
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Liu Yu <allanyuliu@tencent.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AND instruction is erroneously using the X register instead
of the K register.
Signed-off-by: Brendan Hickey <bhickey@google.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 12a2856b60.
The commit above doesn't appear to be necessary any more as the
checksums appear to be correctly computed/validated.
Additionally the above commit breaks kvm configurations where
one VM is using a device that support checksum offload (virtio) and
the other VM does not.
In this case, packets leaving virtio device will have CHECKSUM_PARTIAL
set. The packets is forwarded to a macvtap that has offload features
turned off. Since we use CHECKSUM_UNNECESSARY, the host does does not
update the checksum and thus a bad checksum is passed up to
the guest.
CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrian Nord <nightnord@gmail.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following is a problematic configuration:
VM1: virtio-net device connected to macvtap0@eth0
VM2: e1000 device connect to macvtap1@eth0
The problem is is that virtio-net supports checksum offloading
and thus sends the packets to the host with CHECKSUM_PARTIAL set.
On the other hand, e1000 does not support any acceleration.
For small TCP packets (and this includes the 3-way handshake),
e1000 ends up receiving packets that only have a partial checksum
set. This causes TCP to fail checksum validation and to drop
packets. As a result tcp connections can not be established.
Commit 3e4f8b7873
macvtap: Perform GSO on forwarding path.
fixes this issue for large packets wthat will end up undergoing GSO.
This commit adds a check for the non-GSO case and attempts to
compute the checksum for partially checksummed packets in the
non-GSO case.
CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrian Nord <nightnord@gmail.com>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: Michael S. Tsirkin <mst@redhat.com>
CC: Jason Wang <jasowang@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both TLP and Fast Open call __tcp_retransmit_skb() instead of
tcp_retransmit_skb() to avoid changing tp->retrans_out.
This has the side effect of missing SNMP counters increments as well
as tcp_info tcpi_total_retrans updates.
Fix this by moving the stats increments of into __tcp_retransmit_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds set_rx_int_on_com function for interrupt when
dma is completed.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds rxqueue enable function according to number of rxqueue
and adds rxqueue disable function for removing.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves sw reset to probe function because
sw reset is needed early stage before open function.
Signed-off-by: Byungho An <bh74.an@samsung.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add handling for " 8 GT/s" in print_port_info().
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following sparse warnings:
drivers/net/ethernet/altera/altera_msgdma.c:23:5: warning: symbol 'msgdma_initialize' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:28:6: warning: symbol 'msgdma_uninitialize' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:32:6: warning: symbol 'msgdma_reset' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:77:6: warning: symbol 'msgdma_disable_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:83:6: warning: symbol 'msgdma_enable_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:89:6: warning: symbol 'msgdma_disable_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:95:6: warning: symbol 'msgdma_enable_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:101:6: warning: symbol 'msgdma_clear_rxirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:107:6: warning: symbol 'msgdma_clear_txirq' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:114:5: warning: symbol 'msgdma_tx_buffer' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:129:5: warning: symbol 'msgdma_tx_completions' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:154:5: warning: symbol 'msgdma_add_rx_desc' was not declared. Should it be static?
drivers/net/ethernet/altera/altera_msgdma.c:181:5: warning: symbol 'msgdma_rx_status' was not declared. Should it be static?
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sgdma_descrip is a function name as well as the name of a struct. In
sgdma_initialize(), we should initialize the descriptor length field
with the actual length of a descriptor not with the size of the
function. In order to prevent such things from happening in the future,
rename the function to sgdma_setup_descrip().
Found by sparse which yields the following warning:
drivers/net/ethernet/altera/altera_sgdma.c:74:30: warning: expression using sizeof on a function
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: a53268be0c ('rtlwifi: rtl8192cu: Fix too long disable of IRQs')
Cc: stable@vger.kernel.org
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beginning with kernel 3.13, this driver fails on some systems. The problem
was bisected to:
Commit 1bf4bbb402
Author: Felix Fietkau <nbd@openwrt.org>
Title: mac80211: send control port protocol frames to the VO queue
There is noting wrong with the above commit. The regression occurs because
V0 queue on RTL8192SE cards uses priority 6, not the usual 7. The fix is to
modify the rtl8192se routine that sets the correct transmit queue.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=74541
Reported-by: Alex Miller <almiller_1@yahoo.co.uk>
Tested-by: Alex Miller <almiller_1@yahoo.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [3.13+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some corner cases where the driver could get stuck with a full
tid queue that is paused, leading to a software tx queue hang.
Since the tx queueing rework, pausing per-tid queues on aggregation
session setup is no longer necessary. The driver will assign sequence
numbers to buffered frames when a new session is established, in order
to get the correct starting sequence number.
mac80211 prevents new frames from entering the queue during setup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the amount of noise fluctuates strongly, low immunity settings
can sometimes disrupt signal detection on AR913x chips. When that
happens, no OFDM/CCK errors are reported anymore, and ANI tunes the
radio to the lowest immunity settings.
Usually rx/tx fails as well in that case.
To fix this, keep noise immunity settings at or above ANI default level,
which will keep radio parameters at or above INI values.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix format string mismatch in bonding_show_min_links().
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To properly match iif in ip rules we have to provide
LOOPBACK_IFINDEX in flowi6_iif, not 0. Some ip6mr_fib_lookup
and fib6_rule_lookup callers need such fix.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't transition to the PF state on every strike after 'Path.Max.Retrans'.
Per draft-ietf-tsvwg-sctp-failover-03 Section 5.1.6:
Additional (PMR - PFMR) consecutive timeouts on a PF destination
confirm the path failure, upon which the destination transitions to the
Inactive state. As described in [RFC4960], the sender (i) SHOULD notify
ULP about this state transition, and (ii) transmit heartbeats to the
Inactive destination at a lower frequency as described in Section 8.3 of
[RFC4960].
This also prevents sending SCTP_ADDR_UNREACHABLE to the user as the state
bounces between SCTP_INACTIVE and SCTP_PF for each subsequent strike.
Signed-off-by: Karl Heiss <kheiss@gmail.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit cc9fa74e2a ("slip/slcan: added locking in wakeup function") a
formerly missing locking was added to slip.c and slcan.c by Andre Naujoks.
Alexander Stein contributed the fix 367525c8c2 ("can: slcan: Fix spinlock
variant") as the kernel lock debugging advised to use spin_lock_bh() instead
of just using spin_lock().
This fix has to be applied to the same code section in slip.c for the same
reason too.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bjørn Mork says:
====================
qmi_wwan: adding a few new devices
Adding some new and some old QMI devices. A similar series for
usb-serial support will be posted as well.
These new device ID patches should also go to all maintained stable kernels
where they apply. I believe that should be stable-3.10 and newer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan writes:
"The Dell drivers use the same configuration for PIDs:
81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card
These devices are all clearly Sierra devices, but are also definitely
Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750.
>From DellGobi5kSetup.exe from the Dell drivers:
usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of older CMOTech modems are based on Qualcomm
chips and exporting a QMI/wwan function.
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 813b3b5db8 (ipv4: Use caller's on-stack flowi as-is
in output route lookups.) introduces another regression which
is very similar to the problem of commit e6b45241c (ipv4: reset
flowi parameters on route connect) wants to fix:
Before we call ip_route_output_key() in sctp_v4_get_dst() to
get a dst that matches a bind address as the source address,
we have already called this function previously and the flowi
parameters have been initialized including flowi4_oif, so when
we call this function again, the process in __ip_route_output_key()
will be different because of the setting of flowi4_oif, and we'll
get a networking device which corresponds to the inputted flowi4_oif
as the output device, this is wrong because we'll never hit this
place if the previously returned source address of dst match one
of the bound addresses.
To reproduce this problem, a vlan setting is enough:
# ifconfig eth0 up
# route del default
# vconfig add eth0 2
# vconfig add eth0 3
# ifconfig eth0.2 10.0.1.14 netmask 255.255.255.0
# route add default gw 10.0.1.254 dev eth0.2
# ifconfig eth0.3 10.0.0.14 netmask 255.255.255.0
# ip rule add from 10.0.0.14 table 4
# ip route add table 4 default via 10.0.0.254 src 10.0.0.14 dev eth0.3
# sctp_darn -H 10.0.0.14 -P 36422 -h 10.1.4.134 -p 36422 -s -I
You'll detect that all the flow are routed to eth0.2(10.0.1.254).
Signed-off-by: Xufeng Zhang <xufeng.zhang@windriver.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
