Add a module parameter to inhibit disconnect/reselect for individual
targets. This gains compatibility with Aztec PowerMonster SCSI/SATA
adapters with buggy firmware. (No fix is available from the vendor.)
Apparently these adapters pass-through the product/vendor of the attached
SATA device. Since they can't be identified from the response to an INQUIRY
command, a device blacklist flag won't work.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Link: https://lore.kernel.org/r/993b17545990f31f9fa5a98202b51102a68e7594.1573875417.git.fthain@telegraphics.com.au
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When do_abort() succeeds, the target will go to BUS FREE phase and there
will be no connected command. Therefore, that function should clear the
Initiator Command Register before returning. It already does so in case of
NCR5380_poll_politely() failure; do the same for the other error case too,
that is, NCR5380_transfer_pio() failure.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Ondrej Zary <linux@zary.sk>
Link: https://lore.kernel.org/r/4277b28ee2551f884aefa85965ef3c498344f301.1573875417.git.fthain@telegraphics.com.au
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most NCR5380 drivers calculate the residual for every data transfer.
(A few drivers just set it to zero.) Pass this quantity back to the scsi
mid-layer on command completion.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: Ondrej Zary <linux@zary.sk>
Link: https://lore.kernel.org/r/1f26ead9dd0dc053fcd27979d69a7ca74b6589b4.1573875417.git.fthain@telegraphics.com.au
Reviewed-and-tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@zary.sk>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list. This necessitates a large number of driver
changes because the previous guarantee that if a driver specified
SG_ALL as the size of its scatter list, it would get a non-chained
list and didn't need to bother with scatterlist iterators is now
broken and every driver *must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXSTzzCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishZB+AP9I8j/s
wWfg0Z3WNuf4D5I3rH4x1J3cQTqPJed+RjwgcQEA1gZvtOTg1ZEn/CYMVnaB92x0
t6MZSchIaFXeqfD+E7U=
=cv8o
-----END PGP SIGNATURE-----
Merge tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI scatter-gather list updates from James Bottomley:
"This topic branch covers a fundamental change in how our sg lists are
allocated to make mq more efficient by reducing the size of the
preallocated sg list.
This necessitates a large number of driver changes because the
previous guarantee that if a driver specified SG_ALL as the size of
its scatter list, it would get a non-chained list and didn't need to
bother with scatterlist iterators is now broken and every driver
*must* use scatterlist iterators.
This was broken out as a separate topic because we need to convert all
the drivers before pulling the trigger and unconverted drivers kept
being found, necessitating a rebase"
* tag 'scsi-sg' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (21 commits)
scsi: core: don't preallocate small SGL in case of NO_SG_CHAIN
scsi: lib/sg_pool.c: clear 'first_chunk' in case of no preallocation
scsi: core: avoid preallocating big SGL for data
scsi: core: avoid preallocating big SGL for protection information
scsi: lib/sg_pool.c: improve APIs for allocating sg pool
scsi: esp: use sg helper to iterate over scatterlist
scsi: NCR5380: use sg helper to iterate over scatterlist
scsi: wd33c93: use sg helper to iterate over scatterlist
scsi: ppa: use sg helper to iterate over scatterlist
scsi: pcmcia: nsp_cs: use sg helper to iterate over scatterlist
scsi: imm: use sg helper to iterate over scatterlist
scsi: aha152x: use sg helper to iterate over scatterlist
scsi: s390: zfcp_fc: use sg helper to iterate over scatterlist
scsi: staging: unisys: visorhba: use sg helper to iterate over scatterlist
scsi: usb: image: microtek: use sg helper to iterate over scatterlist
scsi: pmcraid: use sg helper to iterate over scatterlist
scsi: ipr: use sg helper to iterate over scatterlist
scsi: mvumi: use sg helper to iterate over scatterlist
scsi: lpfc: use sg helper to iterate over scatterlist
scsi: advansys: use sg helper to iterate over scatterlist
...
A PDMA error is handled in the core driver by setting the device's 'borken'
flag and aborting the command. Unfortunately, do_abort() is not
dependable. Perform a SCSI bus reset instead, to make sure that the command
fails and gets retried.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org # v4.20+
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The reselection interrupt gets disabled during selection and must be
re-enabled when hostdata->connected becomes NULL. If it isn't re-enabled a
disconnected command may time-out or the target may wedge the bus while
trying to reselect the host. This can happen after a command is aborted.
Fix this by enabling the reselection interrupt in NCR5380_main() after
calls to NCR5380_select() and NCR5380_information_transfer() return.
Cc: Michael Schmitz <schmitzmic@gmail.com>
Cc: stable@vger.kernel.org # v4.9+
Fixes: 8b00c3d5d4 ("ncr5380: Implement new eh_abort_handler")
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Stan Johnson <userm57@yahoo.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Unlike the legacy I/O path, scsi-mq preallocates a large array to hold
the scatterlist for each request. This static allocation can consume
substantial amounts of memory on modern controllers which support a
large number of concurrently outstanding requests.
To facilitate a switch to a smaller static allocation combined with a
dynamic allocation for requests that need it, we need to make sure all
SCSI drivers handle chained scatterlists correctly.
Convert remaining drivers that directly dereference the scatterlist
array to using the iterator functions.
[mkp: clarified commit message]
Cc: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adjust comments accordingly.
Cc: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I overlooked this statement when I recently converted the function result
type from struct scsi_cmnd * to bool. No change to object code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SR_RST bit isn't latched. Hence, detecting a bus reset isn't reliable.
When it is detected, the right thing to do is to drop all connected and
disconnected commands. The code for that is already present so refactor it and
call it when SR_RST is set.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The X3T9.2 specification (draft) says, under "6.1.4.2 RESELECTION time-out
procedure", that a target may assert RST or go to BUS FREE phase if the
initiator does not respond within 200 us. Something like this has been
observed with AztecMonster II target. When it happens, all we can do is wait
for the target to try again.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION",
... The reselected initiator shall then assert the BSY signal
within a selection abort time of its most recent detection of being
reselected; this is required for correct operation of the time-out
procedure.
The selection abort time is only 200 us which may be insufficient time for a
printk() call. Move the diagnostics to the error paths.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When NCR5380_abort() returns FAILED, the driver forgets that the target is
still busy. Hence, further commands may be sent to the target, which may fail
during selection and produce the error message, "reselection after won
arbitration?". Prevent this by leaving the busy flag set when NCR5380_abort()
fails.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The X3T9.2 specification (draft) says, under "6.1.4.1 RESELECTION", that "the
initiator shall not respond to a RESELECTION phase if other than two SCSI ID
bits are on the DATA BUS." This issue (too many bits set) has been observed in
the wild, so add a check.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When sense data is valid, call set_driver_byte(cmd, DRIVER_SENSE). Otherwise
some callers of scsi_execute() will ignore sense data. Don't set DID_ERROR or
DID_RESET just because sense data is missing.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly needed because an AztecMonster II target has been observed
disconnecting REQUEST SENSE commands and then failing to reselect properly.
Suggested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The return value is taken to mean "retry" or "don't retry". Change it to bool
to improve readability. Fix related comments. No functional change.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Replace a 'goto' statement with a simple 'return' where possible. This
improves readability. No functional change.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When doing a host reset we should be clearing all outstanding commands, not
just the command triggering the reset.
[mkp: adjusted Hannes' SoB address]
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Ondrey Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=3O85
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual suspects: lpfc, qla2xxx, hisi_sas,
megaraid_sas, pm80xx, mpt3sas, be2iscsi, hpsa. and a host of minor
updates.
There's no major behaviour change or additions to the core in all of
this, so the potential for regressions should be small (biggest
potential being in the scsi error handler changes)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: lpfc: Fix hard lock up NMI in els timeout handling.
scsi: mpt3sas: remove a stray KERN_INFO
scsi: mpt3sas: cleanup _scsih_pcie_enumeration_event()
scsi: aacraid: use timespec64 instead of timeval
scsi: scsi_transport_fc: add 64GBIT and 128GBIT port speed definitions
scsi: qla2xxx: Suppress a kernel complaint in qla_init_base_qpair()
scsi: mpt3sas: fix dma_addr_t casts
scsi: be2iscsi: Use kasprintf
scsi: storvsc: Avoid excessive host scan on controller change
scsi: lpfc: fix kzalloc-simple.cocci warnings
scsi: mpt3sas: Update mpt3sas driver version.
scsi: mpt3sas: Fix sparse warnings
scsi: mpt3sas: Fix nvme drives checking for tlr.
scsi: mpt3sas: NVMe drive support for BTDHMAPPING ioctl command and log info
scsi: mpt3sas: Add-Task-management-debug-info-for-NVMe-drives.
scsi: mpt3sas: scan and add nvme device after controller reset
scsi: mpt3sas: Set NVMe device queue depth as 128
scsi: mpt3sas: Handle NVMe PCIe device related events generated from firmware.
scsi: mpt3sas: API's to remove nvme drive from sml
scsi: mpt3sas: API 's to support NVMe drive addition to SML
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 5380 drivers only support asynchronous transfers and the 5380
controllers only have narrow busses. Hence, the core driver will reject
any SDTR and WDTR messages from target devices. Don't log this, it's
expected behaviour. Also, fix the off-by-one array indices in the
arguments to scmd_printk().
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The bus reset handler really is a host reset, so move it to
eh_bus_reset_handler.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Handle timeout or bus phase change errors that could occur when sending
the IDENTIFY message.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid various warnings from "make C=1" by annotating a couple of
unlock-then-lock sequences, replacing a zero with NULL and correcting
some type casts.
Also avoid a warning from "make W=1" by adding braces.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The DIFFERENTIAL and PARITY option macros are unused: no supported
hardware uses differential signalling and the core driver never
implemented parity checking. These options just waste space in the host
info string.
While we are here, fix a typo in the NCR5380_info() kernel-doc comment.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use standard probe_irq_on() and probe_irq_off() functions instead of own
implementation. This prevents warning messages like this in the kernel
log: genirq: Flags mismatch irq 1. 00000000 (NCR-probe) vs. 00000080
(i8042)
Move the IRQ trigger code from NCR5380 to g_NCR5380 where it is used.
Also clear interrupt flag before and after the probe.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If a NCR5380 host instance ends up on a shared interrupt line then
this printk will be a problem. It is already a problem on some Mac
models: when testing mac_scsi on a PowerBook 180 I found that PDMA
transfers (but not PIO transfers) cause the message to be logged.
These spurious interrupts don't appear to come from the DRQ signal from
the 5380. And they don't happen at all on the Mac LC III. A comment in
the NetBSD source code mentions this mystery. Testing seems to show
that we can safely ignore these interrupts.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Apply prototypes to get consistent function signatures for the DMA
functions implemented in the board-specific drivers. To avoid using
macros to alter actual parameters, some of those functions are reworked
slightly.
This is a step toward the goal of passing the board-specific routines
to the core driver using an ops struct (as in a platform driver or
library module).
This also helps fix some inconsistent types: where the core driver uses
ints (cmd->SCp.this_residual and hostdata->dma_len) for keeping track of
transfers, certain board-specific routines used unsigned long.
While we are fixing these function signatures, pass the hostdata pointer
to DMA routines instead of a Scsi_Host pointer, for shorter and faster
code.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pass a NCR5380_hostdata struct pointer to the board-specific routines
instead of a Scsi_Host struct pointer. This reduces pointer chasing in
the PIO and PDMA fast paths. The old way was a mistake because it is
slow and the board-specific code is not concerned with the mid-layer.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For timeout values adopt unsigned long, which is the type of jiffies etc.
For chip register values and bit masks pass u8, which is the return type
of readb, inb etc.
For device register offsets adopt unsigned int, as it is suitable for
adding to base addresses.
Pass the NCR5380_hostdata pointer to the board-specific routines instead
of the Scsi_Host pointer. The board-specific code is concerned with
hardware and not with SCSI protocol or the mid-layer.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The various 5380 drivers inconsistently store register pointers
either in the Scsi_Host struct "legacy crap" area or in special,
board-specific members of the NCR5380_hostdata struct. Uniform
use of the latter struct makes for simpler and faster code (see
the following patches) and helps to reduce use of the
NCR5380_implementation_fields macro.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When polling a device register under irq lock the polling loop terminates
after a given number of jiffies. Make this timeout independent of the HZ
setting.
All 5380 drivers benefit from this patch, which optimizes the PIO fast
path, because they all use PIO transfers (for phases other than DATA IN
and DATA OUT). Some cards support only PIO transfers (even for DATA
phases). CPU cycles are scarce on some of these systems, so a small
improvement here makes a big difference.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The g_NCR5380 has been converted to more regular probing, which
means its probe function can now be invoked after the __init section
is discarded, as pointed out by this kbuild warning:
WARNING: drivers/scsi/built-in.o(.text+0x3a105): Section mismatch in reference from the function generic_NCR5380_isa_match() to the function .init.text:probe_intr()
WARNING: drivers/scsi/built-in.o(.text+0x3a145): Section mismatch in reference from the function generic_NCR5380_isa_match() to the variable .init.data:probe_irq
To make sure this works correctly in all cases, let's remove
the __init and __initdata annotations.
Fixes: a8cfbcaec0 ("scsi: g_NCR5380: Stop using scsi_module.c")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Large PIO transfers are broken up into chunks to try to avoid disabling
local IRQs for long periods. But IRQs are still disabled for too long
and this causes SCC FIFO overruns during serial port transfers.
This patch reduces the PIO chunk size to reduce interrupt latency to
something on the order of milliseconds, at the expense of additional CPU
overhead from extra iterations of the NCR5380_main() loop.
That CPU overhead is a problem for slow machines (e.g. mac_scsi on 25
MHz 68030) but these machines generally use PDMA not PIO. This patch
doesn't make the overhead any worse on my Mac LC III (because it only
gets about 510 accesses per ms).
This patch decreases disk performance by a fraction of one percent for
dmx3191d on my 333 MHz PowerPC 750. Other affected hardware (such as
g_NCR5380 on x86) was not tested but 5380 ISA cards generally use PDMA
and not PIO.
[mkp: fix whitespace]
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Laurence Oberman <loberman@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
With commit 3a0f64bfa9 ("mac_scsi: Fix pseudo DMA implementation")
some versions of gcc now warn:
In file included from drivers/scsi/mac_scsi.c:335:
drivers/scsi/NCR5380.h:295: warning: `NCR5380_poll_politely' declared inline after being called
drivers/scsi/NCR5380.h:295: warning: previous declaration of `NCR5380_poll_politely' was here
Avoid this by defining NCR5380_poll_politely() in NCR5380.h.
[mkp: checkpatch warnings]
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I'm told that some targets are liable to disconnect a REQUEST SENSE
command. Theoretically this would cause a command undergoing autosense to
be moved onto the disconnected list. The bus reset handler must call
complete_cmd() for these commands, otherwise the hostdata->sensing pointer
will not get cleared. That would cause autosense processing to stall and
a timeout or an incorrect scsi_eh_restore_cmnd() would eventually follow.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reported-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Decode all bits in the chip registers. They are all useful at times.
Fix printk severity so that this output can be suppressed along with
the other debugging output.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver has a limit of eight LUs because of the byte-sized bitfield
that is used for busy flags. That means the maximum LUN is 7. The default
is 8.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Now that atari_scsi and sun3_scsi have been converted to use the NCR5380.c
core driver, remove atari_NCR5380.c. Also remove the last vestiges of its
Tagged Command Queueing implementation from the wrapper drivers.
The TCQ support in atari_NCR5380.c is abandoned by this patch. It is not
merged into the remaining core driver because,
1) atari_scsi defines SUPPORT_TAGS but leaves FLAG_TAGGED_QUEUING disabled
by default, which indicates that it is mostly undesirable.
2) I'm told that it doesn't work correctly when enabled.
3) The algorithm does not make use of block layer tags which it will have
to do because scmd->tag is deprecated.
4) sun3_scsi doesn't define SUPPORT_TAGS at all, yet the the SUPPORT_TAGS
macro interacts with the CONFIG_SUN3 macro in 'interesting' ways.
5) Compile-time configuration with macros like SUPPORT_TAGS caused the
configuration space to explode, leading to untestable and unmaintainable
code that is too hard to reason about.
The merge_contiguous_buffers() code is also abandoned. This was unused
by sun3_scsi. Only atari_scsi used it and then only on TT, because only TT
supports scatter/gather. I suspect that the TT would work fine with
ENABLE_CLUSTERING instead. If someone can benchmark the difference then
perhaps the merge_contiguous_buffers() code can be be justified. Until
then we are better off without the extra complexity.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for the custom Sun 3 DMA logic to the NCR5380.c core driver.
This code is copied from atari_NCR5380.c.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add support for the Atari ST DMA chip to the NCR5380.c core driver.
This code is copied from atari_NCR5380.c.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Adopt the DMA implementation from atari_NCR5380.c. This means that
atari_scsi and sun3_scsi can make use of the NCR5380.c core driver
and the atari_NCR5380.c driver fork can be made redundant.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Standardize the DMA setup hooks so that the DMA implementation in
atari_NCR5380.c can be reconciled with pseudo DMA implementation in
NCR5380.c.
Calls to NCR5380_dma_recv_setup() and NCR5380_dma_send_setup() return
a negative value on failure, zero on PDMA transfer success and a positive
byte count for DMA setup success.
This convention is not entirely new, but is now applied consistently.
Also remove a pointless Status Register access: the *phase assignment is
redundant because after NCR5380_transfer_dma() returns control to
NCR5380_information_transfer(), that routine then returns control
to NCR5380_main(), which means *phase is dead.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Those wrapper drivers which use DMA define the REAL_DMA macro and
those which use pseudo DMA define PSEUDO_DMA. These macros need to be
removed for a number of reasons, not least of which is to have drivers
share more code.
Redefine the PDMA send and receive hooks as DMA setup hooks, so that the
DMA code can be shared by all 5380 wrapper drivers. This will help to
reunify the forked core driver.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The io_recovery_delay macro is intended to insert a microsecond delay
between the chip register accesses that begin a DMA operation. This
is reportedly needed for some ISA boards.
Reverse the sense of the macro test so that in the common case,
where no delay is required, drivers need not define the macro.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For those wrapper drivers which only implement Programmed IO, have
NCR5380_dma_xfer_len() evaluate to zero. That allows PDMA to be easily
disabled at run-time and so the PSEUDO_DMA macro is no longer needed.
Also remove the spin counters used for debugging pseudo DMA drivers.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Tested-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
