Attaching a keyboard, using it as a wakeup via
|for f in $(find /sys/devices/ocp.3/47400000.usb -name wakeup)
|do
| echo enabled > $f
|done
going into standby
| echo standby > /sys/power/state
and now a wake up by a pressing a key.
What happens is that the system wakes up but the USB device is dead. The
USB stack tries to send a few control URBs but nothing comes back.
Eventually it gaves up and the device remains dead:
|[ 632.559678] PM: Wakeup source USB1_PHY
|[ 632.581074] PM: noirq resume of devices complete after 21.261 msecs
|[ 632.607521] PM: early resume of devices complete after 10.360 msecs
|[ 632.616854] net eth2: initializing cpsw version 1.12 (0)
|[ 632.704126] net eth2: phy found : id is : 0x4dd074
|[ 636.704048] libphy: 4a101000.mdio:00 - Link is Up - 1000/Full
|[ 638.444620] usb 1-1: reset low-speed USB device number 2 using musb-hdrc
|[ 653.713435] usb 1-1: device descriptor read/64, error -110
|[ 669.093435] usb 1-1: device descriptor read/64, error -110
|[ 669.473424] usb 1-1: reset low-speed USB device number 2 using musb-hdrc
|[ 684.743436] usb 1-1: device descriptor read/64, error -110
|[ 690.065097] PM: resume of devices complete after 57450.744 msecs
|[ 690.076601] PM: Finishing wakeup.
|[ 690.076627] Restarting tasks ...
It seems that since we got woken up via MUSB_INTR_RESUME the
musb_host_finish_resume() callback is executed before the
resume-callbacks of the PHY and glue layer are invoked. If I delay it
until the glue layer resumed then I don't see this problem.
I also move musb_host_resume_root_hub() into that callback since I don't
see any reason in doing anything resume-link if there are still pieces
not restored.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The am335x-evmsk support two kinds of suspend:
- standby
the USB device remains powered while the system goes into suspend
- mem
the USB device becomes powerless while the system goes into suspend.
In the "standby" case the device resumes quickly. In the "mem" case the
system hangs for a few seconds. It seems to me that the USB-device has
no address (it was disconnected) and the USB stack thinks that it is
fully operational and GetPortStatus returns the status from before the
suspend so it is not a big help here.
This adds a check in the resume path to see if the device mode (A or B)
and the speed is the same. If the device went missing between
suspend/resume (VBUS went down) then MUSB seems to go into B mode and
HS/FS bits are cleared. In that case we clear the port1_status bits and
assume a disconnect. Once the stack learns this it does a "logical
disconnect" and removes the USB-device quickly. Should the device remain
connected during the suspend then MUSB will receives a "CONNECT" interrupt.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before using the PHY framework instead of the USB PHY one, we need to
move the OTG state into another place, since it won't be available when
USB PHY isn't used. This patch moves the OTG state into the OTG
structure, and makes all the needed modifications in the drivers
using the OTG state.
[ balbi@ti.com : fix build regressions with phy-tahvo.c, musb_dsps.c,
phy-isp1301-omap, and chipidea's debug.c ]
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit 0ec8fd70fb ("USB: musb: fix possible panic while resuming")
musb_resume() became musb_resume_early() in order to enable the clocks
early on resume. This piece of the resume code was removed later in
commit 034917612 ("usb: musb: move clock handling to glue layer").
In between the function was renamed from musb_resume_early() to
musb_resume_noirq() by commit commit 48fea9659e ("USB: Rework musb
suspend()/resume_early()").
Now I see that first musb_core is resumed followed by phy and glue
layer and I ask myself is this really what we intend to do? This kind
of revoked the purpose of the first commit (0ec8fd70fb).
Because of this and because it looks wrong to resume (core) before the
glue layer I push it to the ->resume callback.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sanity check on resource happening with devm_ioremap_resource().
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The OMAP2+ MUSB glue layer still uses a bare number for the DEVCTL.B-Device bit
in one place, while there's #define MUSB_DEVCTL_BDEVICE for that.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that no UDC driver relies on the extra
'driver' argument to ->udc_stop(), we can
safely remove it.
This commit is based on previous work by
Robert Baldyga <r.baldyga@samsung.com> which
can be found at [1]; however that patch turned
out to have a high probability of regressing
many UDC drivers because of a blind search & replace
s/driver/$udc->driver/ which caused the 'driver'
argument to stop_activity() to be a valid non-NULL
pointer when it should be NULL, thus causing UDCs
to mistakenly call gadget driver's ->disconnect()
callback.
[1] http://markmail.org/message/x5zneg4xea4zntab
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
now that we provide generic register/unregister
debugging messages from udc-core, we can remove
the same messages from this driver.
Signed-off-by: Felipe Balbi <balbi@ti.com>
future patches will remove the extra 'driver'
argument to ->udc_stop(), in order to do that,
we must make sure that our UDC does not rely
on it first.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The drivers should use dmaengine_terminate_all() or dmaengine_slave_config()
API instead of accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The memory subsystem has already had similar message for it.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So testing managed to configure musb in DMA mode but not load the
matching cppi41 driver for DMA. This results in
|musb-hdrc musb-hdrc.0.auto: Failed to request rx1.
|musb-hdrc musb-hdrc.0.auto: musb_init_controller failed with status -517
|platform musb-hdrc.0.auto: Driver musb-hdrc requests probe deferral
which is "okay". Once the driver is loaded we re-try probing and
everyone is happy. Until then if you try suspend say
echo mem > /sys/power/state
then you go boom
|Unable to handle kernel NULL pointer dereference at virtual address 000003a4
|pgd = cf50c000
|[000003a4] *pgd=8f6a3831, *pte=00000000, *ppte=00000000
|Internal error: Oops: 17 [#1] ARM
|PC is at dsps_suspend+0x18/0x9c [musb_dsps]
|LR is at dsps_suspend+0x18/0x9c [musb_dsps]
|pc : [<bf08e268>] lr : [<bf08e268>] psr: a0000013
|sp : cbd97e00 ip : c0af4394 fp : 00000000
|r10: c0831d90 r9 : 00000002 r8 : cf6da410
|r7 : c03ba4dc r6 : bf08f224 r5 : 00000000 r4 : cbc5fcd0
|r3 : bf08e250 r2 : bf08f264 r1 : cf6da410 r0 : 00000000
|[<bf08e268>] (dsps_suspend [musb_dsps]) from [<c03ba508>] (platform_pm_suspend+0x2c/0x54)
|Code: e1a04000 e9900041 e2800010 eb4caa8e (e59053a4)
because platform_get_drvdata(glue->musb) returns a NULL pointer as long as the
device is not fully probed.
Tested-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit 468bcc2a2c ("usb: musb: dsps: kill OTG timer on suspend") stopped
the timer in suspend path but forgot the re-enable it in the resume
path. This patch fixes the behaviour.
Cc: <stable@vger.kernel.org> # v3.14+
Fixes 468bcc2a2c "usb: musb: dsps: kill OTG timer on suspend"
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit c58d80f52 ("usb: musb: Ensure that cppi41 timer gets armed on
premature DMA TX irq") fixed hrtimer scheduling bug. There is one left
which does not trigger that often.
The following scenario is still possible:
lock(&x->lock);
hrtimer_start(&x->t);
unlock(&x->lock);
expires:
t->function();
lock(&x->lock);
lock(&x->lock); if (!hrtimer_queued(&x->t))
hrtimer_start(&x->t);
unlock(&x->lock);
if (!list_empty(x->early_tx_list))
ret = HRTIMER_RESTART;
-> hrtimer_forward_now(...)
} else
ret = HRTIMER_NORESTART;
unlock(&x->lock);
and the timer callback returns HRTIMER_RESTART for an armed timer. This
is wrong and we run into the BUG_ON() in __run_hrtimer().
This can happens on SMP or PREEMPT-RT.
The patch fixes the problem by only starting the timer if the timer is
not yet queued.
Cc: stable@vger.kernel.org
Reported-by: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
[bigeasy: collected information and created a patch + description based
on it]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the recently introduced usb_gadget_giveback_request() in favor of
direct invocation of the completion routine.
All places in drivers/usb/ matching "[-.]complete(" were replaced with a
call to usb_gadget_giveback_request(). This was compile-tested with all
ARM drivers enabled and runtime-tested for musb.
Signed-off-by: Michal Sojka <sojka@merica.cz>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB hub has started to use a workqueue instead of kthread. Let's update
the documentation and comments here and there.
This patch mostly just replaces "khubd" with "hub_wq". There are only few
exceptions where the whole sentence was updated. These more complicated
changes can be found in the following files:
Documentation/usb/hotplug.txt
drivers/net/usb/usbnet.c
drivers/usb/core/hcd.c
drivers/usb/host/ohci-hcd.c
drivers/usb/host/xhci.c
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed typos in comments of various drivers/usb files
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
if we don't make sure to kill the timer, it could
expire after we have already gated our clocks.
That will trigger a Data Abort exception because
we would try to access register while clock is gated.
Fix that bug.
Cc: <stable@vger.kernel.org> # v3.14+
Fixes 869c597 (usb: musb: dsps: add support for suspend and resume)
Tested-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUDOW+AAoJEHm+PkMAQRiGOXYH/00TPKm8PdM5cXXG2YYYv9eT
W99K7KD2i0/qiVtlGgjjvB7fO3K0HcZusTd2jmVd8IWntXvauq7Zpw5YZkjwu4KX
Y1HCwwCd2aw0FoqgrJhNP3+j5Cr1BD/HLtbffjCe+A3tppOIis4Bwt2wJOoYlXpS
hU9Jxxc4lcRo8YKbffouDo7PIneWeJy8N+WGpUR5BfJIEK0ZZtCUqn3/3WLX4FYu
fE6uiF/bACTpKXU/mo4dDbhZp439H/QdwQc9B0F8+8CBDMXKaNHrPV7kN36T2SWa
fD4boikTsi/yh9Ks1fvHbvNq2N0ihoMnja+vLRyvjAcAQv2fKG3OZtYgFWSdghU=
=Xknd
-----END PGP SIGNATURE-----
Merge tag 'v3.17-rc4' into next
Merge Linux 3.17-rc4 here so we have all the latest
fixes on next too. This also cleans up a few conflicts
when applying patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/gadget/Makefile
drivers/usb/gadget/function/Makefile
drivers/usb/gadget/legacy/Makefile
drivers/usb/phy/phy-samsung-usb.h
Intensive tests with USB audio devices connected to a musb host port
have shown reproducible pops and clicks in both the playback and the
capture stream.
These are related to how the early_tx hrtimer is set up, and it turns
out they can be fixed by reducing the timer's slack value from 40 to
25 us. Also, when the callback is ran without taking action, it should
be rescheduled 20 us later instead of 50 us.
Reported-and-tested-by: Sven Neumann <neumann@teufel.de>
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CPPI TX does not transmit ZLP for TX transfers which
- transfer size is multiple of EP packet size,
- and URB_ZERO_PACKET is set in urb->transfer_flags.
The fix is transmitting the ZLP using PIO mode after the CPPI TX is
done.
Validated using the following usbtest write case in MUSB host mode.
# testusb -t1 -c1
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTzTI9AAoJEIaOsuA1yqREIqcQAJbwMaDb5sp8dWst+nL1Vo8N
08bhOOM+o2KLiIBSNQh1hYtujpa06RSQMiNYZ7F/+R4Q3OAoq+uC0dD69TLEQ3Sd
1xi0UgUTAvtXo13TToRjIi0mYywrrkZ91Maqff5jZKdslOY4ZfAScpUQHyD3i1UO
JNUqpayYAnp8JJIGQ8CG1wAeJh/J8JH3O607vaknKVjds+WMkeC5ubnuV4sgVw71
8JTwxk22EkMTr2MKhHjZwcv016NMEvziinWVoTXcWN2Uwk42Dn1nhfaYWSvg7kZE
8/3t6zzdFMdoeeTEn2xXIQGTjbHW0sBS5+S+6PAon2YbjS3x40cbyLJnZ+KoVXog
iHDKAl5w53gd/7qMiv57dW+HRP0M7/m2iy/owIrY8H8DkM3uwFevaeq/G2raJKmA
frB1k95bSyypN7wVkALYv4nurP5+d7ERy9hPj/49M5giJXPpEIbgKN2qGdafaEx7
xzAI+GqYrFtmmg25+f6AQRicVczQNMCdDT8HPZ04099Z2JVY/4uOoqTl29CePMgo
OXeQ45ECMoJuRSwpF56e8h+qmsXp6WD31IhlcHseTvUvFu0Ex4SgUJhFP2UaF9WP
aOqz0w36yX/ME3VhQk9YImNqGoqEk6fYHIHhxfdDugt0n68+M56EiiwtKvd5v5BI
hCJAMBrv+WCGnJvWunVW
=aJY4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Add sw_babble_control() logic to differentiate between transient
babble and real babble condition. Also add the SW babble control
register definitions.
Babble control register logic is implemented in the latest
revision of AM335x.
Find whether we are running on newer silicon. The babble control
register reads 0x4 by default in newer silicon as opposed to 0
in old versions of AM335x. Based on this enable the sw babble
control logic.
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently musb_platform_reset() is only used by dsps.
In case of BABBLE interrupt for other platforms the musb_platform_reset()
is a NOP. In such situations no need to re-initialize the endpoints.
Also in the latest silicon revision of AM335x, we do have a babble recovery
mechanism without resetting the IP block. In preperation to add that support
its better to have a rest_done return for musb_platform_reset().
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During babble condition both first disconnect of devices are
initiated. Make sure MUSB controller is reset and re-initialized
after all disconnects.
To acheive this schedule a delayed work for babble recovery.
While at that convert udelay to usleep_range.
Refer Documentation/timers/timers-howto.txt
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
BABBLE and RESET share the same interrupt. The interrupt
is considered to be RESET if MUSB is in peripheral mode and
as a BABBLE if MUSB is in HOST mode.
Handle babble condition iff MUSB is in HOST mode.
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Following the name change of the NOP transceiver driver in commit
4525bee (usb: phy: rename usb_nop_xceiv to usb_phy_generic), the
transceiver driver was no longer operable under its old name.
Register the transceiver driver before calling usb_get_phy() to make
sure we are noticed by an error message if it is not available.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The musb/cppi41 code installs a hrtimer to work around DMA completion
interrupts that have fired too early on AM335x hardware. This timer
is currently programmed to first fire 140 microseconds after the DMA
completion callback. According to the commit which introduced it
(a655f481d8, "usb: musb: musb_cppi41: handle pre-mature TX complete
interrupt"), that value is is considered a 'rule of thumb' that worked
well with the test case described in the commit log.
Test show, however, that for USB audio devices and much smaller packet
sizes, the timer has to fire earlier in order to correctly handle the audio
stream. The original test case had output transfer sizes of 1514 bytes, and
a delay of 140 microseconds. For audio devices with 24 bytes channel size, 3
microseconds seem to work well.
Hence, let's assume that the time it takes to clear the bit correlates with
the number of bytes transferred. The referenced commit log mentions such a
suspicion as well. Let the timer fire in cppi41_channel->total_len/10
microseconds to correctly handle both cases.
Also, shorten the interval in which the timer fires again in case of
a non-empty early_tx list.
With these changes in place, both FS and HS audio devices appear to work
well on AM335x hardware.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 1af54b7a4.
The commit tried to address cases in which isochronous transfers are 'not
reliable', most probably in the tests conducted, polling for the
MUSB_TXCSR_TXPKTRDY bit in MUSB_TXCSR is done too late.
Hence, it installs a work struct which basically busy-polls for the bit in a
rather agressive way by rescheduling the work if the FIFO is not empty. With
USB audio devices, tests have shown that it takes approximately 100
iterations of the asynchronous worker until the FIFO signals completion,
which leads to 100% CPU loads when streaming audio.
The issue the patch tried to address can be handled differently, which is
what the next patch does.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before accessing any of an endpoint's CSR registers, make sure the
correct endpoint is selected. Otherwise, data read from or written to
the registers is likely to affect the wrong endpoint as long as the
connected device has more than one endpoint.
This, of course, leads to all sorts of strange effects such as stream
starvation and driver internal state machine confusion due to spurious
interrupts.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The musb/cppi41 glue layer is capable of handling transactions that span
over more than one USB packet by reloading the DMA descriptors
partially. An urb is considered completed when either its transfer
buffer has been filled entirely (actual_length ==
transfer_buffer_length) or if a packet in the stream has less bytes than
the endpoint's wMaxPacketSize.
Once one of the above conditions is met, musb_dma_completion() is called
from cppi41_trans_done(). However, the final decision whether or not to
return the urb to its owner is made by the core and its determination of
the variable 'done' in musb_host_rx(). This code has currently no way of
knowing what the size of the last packet was, and whether or not to
give back the urb due to a short read.
Fix this by introducing a new boolean flag in 'struct dma_channel', and
set it from musb_cppi41.c. If set, it will make the core do what the
DMA layer decided and complete the urb.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The datasheet says that MUSB_TXCSR_FLUSHFIFO is only valid when
MUSB_TXCSR_TXPKTRDY is set as well.
With this patch applied, the warning in this function does no longer
kick in when an USB soundcard is unplugged while the stream is active.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On AM33xx platforms, unplugging a device in the middle of an active
transfer leads to a drop of MUSB_DEVCTL_HM in MUSB_DEVCTL before the
system is informed about a disconnect. This consequently makes the musb
core call the gadget code to handle the interrupt request, which then
crashes the kernel because the relevant pointers haven't been set up
for gadget mode.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
in musb_interrupt() and musb_dma_completion() to detect whether the
controller is in host or peripheral mode. This information is provided
by the driver logic and does not rely on register contents.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just a little cleanup that removes unnecessary casts.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 943c13971c "usb: musb: dsps: implement ->set_mode()"
should have made it possible to use the driver with boards that have
the USBID pin unconnected. This doesn't actually work, since the
driver uses the wrong base address to access the mode register.
Furthermore it uses different base addresses in different places to
access the same register (phy_utmi).
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
For DSPS platform usb_phy_vbus(_off/_on) are NOPs.
So during musb_platform_reset() call usb_phy(_shutdown/_init)
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, a label is done away with and err2 and err3 renamed.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, the unnecesary labels are removed and linux/device.h is
added to make sure the devm_*() routine declarations are unambiguously
available.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, a label is done away with and clk_get is replaced by it
corresponding devm version and the clk_puts are done away with. The
labels are renamed to make them ordered.
The following Coccinelle semantic patch was used for making the change:
@platform@
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces the use of managed interfaces for clk_get and
kzalloc and removes the corresponding free function calls in the probe
and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is no reason for the register accessor functions not to adhere
to the CodingStyle rules.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some TI chips raise the DMA complete interrupt before the actual
transfer has been completed. The code tries to busy wait for a few
microseconds and if that fails it arms an hrtimer to recheck. So far
so good, but that has the following issue:
CPU 0 CPU1
start_next_transfer(RQ1);
DMA interrupt
if (premature_irq(RQ1))
if (!hrtimer_active(timer))
hrtimer_start(timer);
hrtimer expires
timer->state = CALLBACK_RUNNING;
timer->fn()
cppi41_recheck_tx_req()
complete_request(RQ1);
if (requests_pending())
start_next_transfer(RQ2);
DMA interrupt
if (premature_irq(RQ2))
if (!hrtimer_active(timer))
hrtimer_start(timer);
timer->state = INACTIVE;
The premature interrupt of request2 on CPU1 does not arm the timer and
therefor the request completion never happens because it checks for
!hrtimer_active(). hrtimer_active() evaluates:
timer->state != HRTIMER_STATE_INACTIVE
which of course evaluates to true in the above case as timer->state is
CALLBACK_RUNNING.
That's clearly documented:
* A timer is active, when it is enqueued into the rbtree or the
* callback function is running or it's in the state of being migrated
* to another cpu.
But that's not what the code wants to check. The code wants to check
whether the timer is queued, i.e. whether its armed and waiting for
expiry.
We have a helper function for this: hrtimer_is_queued(). This
evaluates:
timer->state & HRTIMER_STATE_QUEUED
So in the above case this evaluates to false and therefor forces the
DMA interrupt on CPU1 to call hrtimer_start().
Use hrtimer_is_queued() instead of hrtimer_active() and evrything is
good.
Reported-by: Torben Hohn <torbenh@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
At probe time, the musb_am335x driver register its childs by
calling of_platform_populate(), which registers all childs in
the devicetree hierarchy recursively.
On the other side, the driver's remove() function uses of_device_unregister()
to remove each child of musb_am335x's.
However, when musb_dsps is loaded, its devices are attached to the musb_am335x
device as musb_am335x childs. Hence, musb_am335x remove() will attempt to
unregister the devices registered by musb_dsps, which produces a kernel panic.
In other words, the childs in the "struct device" hierarchy are not the same
as the childs in the "devicetree" hierarchy.
Ideally, we should enforce the removal of the devices registered by
musb_am335x *only*, instead of all its child devices. However, because of the
recursive nature of of_platform_populate, this doesn't seem possible.
Therefore, as the only solution at hand, this commit disables musb_am335x
driver removal capability, preventing it from being ever removed. This was
originally suggested by Sebastian Siewior:
https://www.mail-archive.com/linux-omap@vger.kernel.org/msg104946.html
And for reference, here's the panic upon module removal:
musb-hdrc musb-hdrc.0.auto: remove, state 4
usb usb1: USB disconnect, device number 1
musb-hdrc musb-hdrc.0.auto: USB bus 1 deregistered
Unable to handle kernel NULL pointer dereference at virtual address 0000008c
pgd = de11c000
[0000008c] *pgd=9e174831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] ARM
Modules linked in: musb_am335x(-) musb_dsps musb_hdrc usbcore usb_common
CPU: 0 PID: 623 Comm: modprobe Not tainted 3.15.0-rc4-00001-g24efd13 #69
task: de1b7500 ti: de122000 task.ti: de122000
PC is at am335x_shutdown+0x10/0x28
LR is at am335x_shutdown+0xc/0x28
pc : [<c0327798>] lr : [<c0327794>] psr: a0000013
sp : de123df8 ip : 00000004 fp : 00028f00
r10: 00000000 r9 : de122000 r8 : c000e6c4
r7 : de0e3c10 r6 : de0e3800 r5 : de624010 r4 : de1ec750
r3 : de0e3810 r2 : 00000000 r1 : 00000001 r0 : 00000000
Flags: NzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 9e11c019 DAC: 00000015
Process modprobe (pid: 623, stack limit = 0xde122240)
Stack: (0xde123df8 to 0xde124000)
3de0: de0e3810 bf054488
3e00: bf05444c de624010 60000013 bf043650 000012fc de624010 de0e3810 bf043a20
3e20: de0e3810 bf04b240 c0635b88 c02ca37c c02ca364 c02c8db0 de1b7500 de0e3844
3e40: de0e3810 c02c8e28 c0635b88 de02824c de0e3810 c02c884c de0e3800 de0e3810
3e60: de0e3818 c02c5b20 bf05417c de0e3800 de0e3800 c0635b88 de0f2410 c02ca838
3e80: bf05417c de0e3800 bf055438 c02ca8cc de0e3c10 bf054194 de0e3c10 c02ca37c
3ea0: c02ca364 c02c8db0 de1b7500 de0e3c44 de0e3c10 c02c8e28 c0635b88 de02824c
3ec0: de0e3c10 c02c884c de0e3c10 de0e3c10 de0e3c18 c02c5b20 de0e3c10 de0e3c10
3ee0: 00000000 bf059000 a0000013 c02c5bc0 00000000 bf05900c de0e3c10 c02c5c48
3f00: de0dd0c0 de1ec970 de0f2410 bf05929c de0f2444 bf05902c de0f2410 c02ca37c
3f20: c02ca364 c02c8db0 bf05929c de0f2410 bf05929c c02c94c8 bf05929c 00000000
3f40: 00000800 c02c8ab4 bf0592e0 c007fc40 c00dd820 6273756d 336d615f 00783533
3f60: c064a0ac de1b7500 de122000 de1b7500 c000e590 00000001 c000e6c4 c0060160
3f80: 00028e70 00028e70 00028ea4 00000081 60000010 00028e70 00028e70 00028ea4
3fa0: 00000081 c000e500 00028e70 00028e70 00028ea4 00000800 becb59f8 00027608
3fc0: 00028e70 00028e70 00028ea4 00000081 00000001 00000001 00000000 00028f00
3fe0: b6e6b6f0 becb59d4 000160e8 b6e6b6fc 60000010 00028ea4 00000000 00000000
[<c0327798>] (am335x_shutdown) from [<bf054488>] (dsps_musb_exit+0x3c/0x4c [musb_dsps])
[<bf054488>] (dsps_musb_exit [musb_dsps]) from [<bf043650>] (musb_shutdown+0x80/0x90 [musb_hdrc])
[<bf043650>] (musb_shutdown [musb_hdrc]) from [<bf043a20>] (musb_remove+0x24/0x68 [musb_hdrc])
[<bf043a20>] (musb_remove [musb_hdrc]) from [<c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<c02ca37c>] (platform_drv_remove) from [<c02c8db0>] (__device_release_driver+0x70/0xc8)
[<c02c8db0>] (__device_release_driver) from [<c02c8e28>] (device_release_driver+0x20/0x2c)
[<c02c8e28>] (device_release_driver) from [<c02c884c>] (bus_remove_device+0xdc/0x10c)
[<c02c884c>] (bus_remove_device) from [<c02c5b20>] (device_del+0x104/0x198)
[<c02c5b20>] (device_del) from [<c02ca838>] (platform_device_del+0x14/0x9c)
[<c02ca838>] (platform_device_del) from [<c02ca8cc>] (platform_device_unregister+0xc/0x20)
[<c02ca8cc>] (platform_device_unregister) from [<bf054194>] (dsps_remove+0x18/0x38 [musb_dsps])
[<bf054194>] (dsps_remove [musb_dsps]) from [<c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<c02ca37c>] (platform_drv_remove) from [<c02c8db0>] (__device_release_driver+0x70/0xc8)
[<c02c8db0>] (__device_release_driver) from [<c02c8e28>] (device_release_driver+0x20/0x2c)
[<c02c8e28>] (device_release_driver) from [<c02c884c>] (bus_remove_device+0xdc/0x10c)
[<c02c884c>] (bus_remove_device) from [<c02c5b20>] (device_del+0x104/0x198)
[<c02c5b20>] (device_del) from [<c02c5bc0>] (device_unregister+0xc/0x20)
[<c02c5bc0>] (device_unregister) from [<bf05900c>] (of_remove_populated_child+0xc/0x14 [musb_am335x])
[<bf05900c>] (of_remove_populated_child [musb_am335x]) from [<c02c5c48>] (device_for_each_child+0x44/0x70)
[<c02c5c48>] (device_for_each_child) from [<bf05902c>] (am335x_child_remove+0x18/0x30 [musb_am335x])
[<bf05902c>] (am335x_child_remove [musb_am335x]) from [<c02ca37c>] (platform_drv_remove+0x18/0x1c)
[<c02ca37c>] (platform_drv_remove) from [<c02c8db0>] (__device_release_driver+0x70/0xc8)
[<c02c8db0>] (__device_release_driver) from [<c02c94c8>] (driver_detach+0xb4/0xb8)
[<c02c94c8>] (driver_detach) from [<c02c8ab4>] (bus_remove_driver+0x4c/0xa0)
[<c02c8ab4>] (bus_remove_driver) from [<c007fc40>] (SyS_delete_module+0x128/0x1cc)
[<c007fc40>] (SyS_delete_module) from [<c000e500>] (ret_fast_syscall+0x0/0x48)
Fixes: 97238b35d5 ("usb: musb: dsps: use proper child nodes")
Cc: <stable@vger.kernel.org> # v3.12+
Acked-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Felipe Balbi <balbi@ti.com>
BABBLE and RESET share the same interrupt. The interrupt
is considered to be RESET if MUSB is in peripheral mode and
as a BABBLE if MUSB is in HOST mode.
Handle babble condition iff MUSB is in HOST mode.
Fixes: ca88fc2ef0 (usb: musb: add a work_struct to recover from babble errors)
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a regression in the upcoming v3.16-rc1, that is caused
by a problem that has been around for a while but now finally
hangs the system. The bootcrawl looks like this:
pinctrl-nomadik soc:pinctrl: pin GPIO256_AF28 already
requested by a03e0000.usb_per5; cannot claim for musb-hdrc.0.auto
pinctrl-nomadik soc:pinctrl: pin-256 (musb-hdrc.0.auto) status -22
pinctrl-nomadik soc:pinctrl: could not request pin 256
(GPIO256_AF28) from group usb_a_1 on device pinctrl-nomadik
musb-hdrc musb-hdrc.0.auto: Error applying setting, reverse
things back
HS USB OTG: no transceiver configured
musb-hdrc musb-hdrc.0.auto: musb_init_controller failed
with status -517
platform musb-hdrc.0.auto: Driver musb-hdrc requests
probe deferral
(...)
The ux500 MUSB driver propagates the OF node to the dynamically
created musb-hdrc device, which is incorrect as it makes the OF
core believe there are two devices spun from the very same
DT node, which confuses other parts of the device core, notably
the pin control subsystem, which will try to apply all the pin
control settings also to the HDRC device as it gets
instantiated. (The OMAP2430 for example, does not set the
of_node member.)
Cc: <stable@vger.kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJTfSbVAAoJEIaOsuA1yqREGU0P/RthhfwpHVOKREnWFvUnRcNn
MAPX1sv11gJiEs2Oe70/9YPL3ZLeV05mBgHoNUjyK5281TK9LDsUW8WwGLKbfe1u
5JsOC+Gmk7aFMCwGfQQKVZpy4UNikpa517Bg+m9oY37rjT2BMsP32Sq1KbD47q1q
0Ybn8iR0ZPAUDnpFc7OKyL9Ocko+AsQo1jmoR1epmhiByfDgzMPPIyE4MLv1SPXi
VvuuWWknTD6xev9m9ELVTo+Or/RNabi04DVOBRV2Qa5csKvkILrBpnCpR0fMTlQ8
ks8Zt0Fnwsre8/L/+HQj+2uOH3w+BDbe9qoVbkmkugZpFvrY0uFGrgGiqt8YOdiL
mQAE+/8lOgnUU5YRTr38h0yIZ1JTHGP1yv9YZwatk65bp2R6o5k5ejf1WnzRqUhy
HvXtILwZZiYknCCdPPEkyqpWEk8NcrLudw2k0EfU3q8JJnHeX+U4YNPhcFkjKido
Oo+SES09gmh+UHAtC1EOtHYs8boNKhe58hL5FzyyKV8zbM2SXmYoDLyBsVyOQQJQ
lDMKhS1+n8QLqBjZ2lypOqLuesHjk+E5iOjrXQZaEfA5eqUxaGezxOdbMkWwPLoS
yKR/tMQ7+OVn8yKhfIyVuzFwQkxc2p4gXtsyDwui6qVVlSrim2+14d2lv5FGVZ48
N8SCQis+ik6tShPOqccH
=Q1jA
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.16 merge window
Not a lot here during this merge window. Mostly we just have
the usual miscellaneous patches (removal of unnecessary prints,
proper dependencies being added to Kconfig, build warning fixes,
new device ID, etc.
Other than those, the only important new features are the
new support for OS Strings which should help Linux Gadget
Drivers behave better under MS Windows. Also Babble Recovery
implementation for MUSB on AM335x. Lastly, we also have
ARCH_QCOM PHY support though phy-msm.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Conflicts:
drivers/usb/phy/phy-mv-u3d-usb.c
The value of the revision is stored in musb->tusb_revision,
so don't re-read it every time.
Exporting tusb_get_revision is not needed anymore,
so the dependency loop between tusb6010 and tusb6010_omap is resolved.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add field to store tusb6010 revision value. Read the revision at
the startup and store to the variable.
Signed-off-by: Matwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The musb/omap2430.c bus glue driver calls usb_hcd_poll_rh_status,
which is only available if CONFIG_USB is also set, i.e. we
are building USB host mode and not just endpoint mode.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
A configuration with CONFIG_USB_MUSB_HDRC=y, CONFIG_USB_TUSB_OMAP_DMA=y
and CONFIG_USB_MUSB_TUSB6010=m causes a link failure because of the
dependency on the tusb_get_revision symbol:
(.text+0x154ce8): undefined reference to `tusb_get_revision'
This patch ensures that either MUSB_HDRC and MUSB_TUSB6010 are
both modules or both built-in, which are the valid configurations.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_in_tusb() is always set to 0, because CONFIG_USB_TUSB6010 is never
set (it should have been CONFIG_USB_MUSB_TUSB6010). But musb_in_tusb()
is unused anyway, so remove a few lines of dead code.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Felipe Balbi <balbi@ti.com>
AM335x MUSB supports both PIO and DMA mode. When DMA mode is
selected users need to explicitly enable the DMA driver. To avoid the
extra configuration select the DMA driver if DMA mode is set for AM335x MUSB.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Depending on PM is not enough, because only PM_RUNTIME could be
selected. Fixes:
drivers/usb/musb/musb_dsps.c:703:12: warning: 'dsps_suspend' defined but not used [-Wunused-function]
drivers/usb/musb/musb_dsps.c:721:12: warning: 'dsps_resume' defined but not used [-Wunused-function]
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When the dsps isr sees a babble error, pass it down to the core for
fixup. Also, provide a .reset hook so the core can call us back.
A babble interrupt error occured when a USB mass storage device
("CHIPSBNK v3.3.9.1", 1e3d:2093) was disconnected from a AM33xx host.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Thomas Mellenthin <mellenthin@teufel.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Handle BABBLE interrupt error conditions from a work struct handler.
This indirection is necessary as we can't be certain that the phy
functions don't sleep.
Platform layer implementation may pass a babble error down to the core
in order to handle it.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Babble interrupts require us to reset the DSPS glue layer. In order to
handle all other recovery tasks independently, add a new hook for
platform-specific implementations of the actual reset.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
it's now very easy to return a platform_device pointer
and have the caller pass it as argument when calling
usb_phy_generic_unregister().
Signed-off-by: Felipe Balbi <balbi@ti.com>
no functional changes, just renaming the function
in order to make it slightly clearer what it should
be used for, also matching the driver name.
Signed-off-by: Felipe Balbi <balbi@ti.com>
When the platform initialization fails due to missing resources, it will
return -EPROBE_DEFER after dsps_musb_init() has been called.
dsps_musb_init() calls dsps_musb_dbg_init() to allocate the debugfs
nodes. At a later point in time, the probe will be retried, and
dsps_musb_dbg_init() will be called again. debugfs_create_dir() will
fail this time, as the node already exists, and so the entire device
probe will fail with -ENOMEM.
Fix this by moving debugfs_remove_recursive() from dsps_remove() to the
plaform's exit function, so it will be cleanly torn down when the probe
fails. It also feels more natural this way, as .exit is the counterpart
to .init.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
on early initialization we could fall into
a situation where the mailbox is called before
MUSB's clocks are running, in order to avoid
that, make sure mailbox is always wrapped with
pm_runtime calls.
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commi 30a70b0 (usb: musb: fix obex in g_nokia.ko
causing kernel panic) removed phy_power_on()
and phy_power_off() calls from runtime PM callbacks
but it failed to note that the driver depended
on pm_runtime_get_sync() calls to power up the PHY,
thus leaving some platforms without any means to
have a working PHY.
Fix that by enabling the phy during omap2430_musb_init()
and killing it in omap2430_musb_exit().
Fixes: 30a70b0 (usb: musb: fix obex in g_nokia.ko causing kernel panic)
Cc: <stable@vger.kernel.org> # v3.14
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reported-by: Michael Scott <hashcode0f@gmail.com>
Tested-by: Michael Scott <hashcode0f@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Reported-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Felipe Balbi <balbi@ti.com>
and a multi-purpose PHY in APM, all adapted to generic PHY framework.
Adapted USB3 PHY driver in OMAP to generic PHY driver and also used
the same driver for SATA in OMAP. It also includes miscellaneous cleanups
and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=mpZ3
-----END PGP SIGNATURE-----
Merge tag 'for_3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
Add new PHY drivers for SATA and USB in exynos, for USB in sunxi,
and a multi-purpose PHY in APM, all adapted to generic PHY framework.
Adapted USB3 PHY driver in OMAP to generic PHY driver and also used
the same driver for SATA in OMAP. It also includes miscellaneous cleanups
and fixes.
Rename struct omap_control_usb to struct omap_control_phy since it can
be used to control PHY of USB, SATA and PCIE. Also move the driver and
include files under *phy* and made the corresponding changes in the users
of phy-omap-control.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
another substantial pull request with new features all over
the place.
dwc3 got a bit closer towards hibernation support with after
a few patches re-factoring code to be reused for hibernation.
Also in dwc3 two new workarounds for known silicon bugs have
been implemented, some randconfig build errors have been fixed,
and it was taught about the new generic phy layer.
MUSB on AM335x now supports isochronous transfers thanks to
George Cherian's work.
The atmel_usba driver got two crash fixes: one when no endpoint
was specified in DeviceTree data and another when stopping the UDC
in DEBUG builds.
Function FS got a much needed fix to ffs_epfile_io() which was
copying too much data to userspace in some cases.
The printer gadget got a fix for a possible deadlock and plugged
a memory leak.
Ethernet drivers now use NAPI for RX which gives improved throughput.
Other than that, the usual miscelaneous fixes, cleanups, and
the like.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AAie
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.15
another substantial pull request with new features all over
the place.
dwc3 got a bit closer towards hibernation support with after
a few patches re-factoring code to be reused for hibernation.
Also in dwc3 two new workarounds for known silicon bugs have
been implemented, some randconfig build errors have been fixed,
and it was taught about the new generic phy layer.
MUSB on AM335x now supports isochronous transfers thanks to
George Cherian's work.
The atmel_usba driver got two crash fixes: one when no endpoint
was specified in DeviceTree data and another when stopping the UDC
in DEBUG builds.
Function FS got a much needed fix to ffs_epfile_io() which was
copying too much data to userspace in some cases.
The printer gadget got a fix for a possible deadlock and plugged
a memory leak.
Ethernet drivers now use NAPI for RX which gives improved throughput.
Other than that, the usual miscelaneous fixes, cleanups, and
the like.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Reprogramming the DMA after tear down is initiated leads to warning.
This is mainly seen with ISOCH since we do a delayed completion for
ISOCH transfers. In ISOCH transfers dma_completion should not reprogram
if the channel tear down is initiated.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If NO_DMA=y:
drivers/built-in.o: In function `txstate':
musb_gadget.c:(.text+0x35955a): undefined reference to `dma_unmap_single'
musb_gadget.c:(.text+0x35957e): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `musb_g_giveback':
(.text+0x359672): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `musb_g_giveback':
(.text+0x3596ba): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `musb_g_giveback':
(.text+0x3596e0): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `rxstate':
musb_gadget.c:(.text+0x3599d0): undefined reference to `dma_unmap_single'
musb_gadget.c:(.text+0x3599f6): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `musb_gadget_queue':
musb_gadget.c:(.text+0x35a8c0): undefined reference to `dma_map_single'
musb_gadget.c:(.text+0x35a8d0): undefined reference to `dma_mapping_error'
musb_gadget.c:(.text+0x35a906): undefined reference to `dma_sync_single_for_cpu'
musb_gadget.c:(.text+0x35a9a0): undefined reference to `dma_unmap_single'
musb_gadget.c:(.text+0x35a9c8): undefined reference to `dma_sync_single_for_cpu'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
instead of relying on the otg pointer, which
can be NULL in certain cases, we can use the
gadget and host pointers we already hold inside
struct musb.
Cc: <stable@vger.kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
debugfs files to show the contents of important dsps registers.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
schedule_delayed_work() takes the delay in jiffies, not msecs.
This bug slipped in with the recent reset logic cleanup
(8ed1fb790e: "usb: musb: finish suspend/reset work independently from
musb_hub_control()").
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace kzalloc by devm_kzalloc and remove the kfree() calls.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_port_reset() is called from musb_hub_control() which in turn holds
a spinlock, so musb_port_reset() is not allowed to call msleep().
With the asynchronous work helpers in place, this is fortunately easy to
fix by rescheduling the reset deassertion function to after the time
when the wait period is finished.
Note, however, that the MUSB_POWER_RESUME bit is only set on AM33xx
processors under rare conditions such as when to another driver
reporting an error during suspend. Hence, this didn't hit me yet in
normal operation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During resume don't touch SUSPENDM/RESUME bits of POWER register
while restoring controller context. These bits might be changed
by the controller during resume operation and so will be different
than what they were during suspend.
e.g. SUSPENDM bit is set by software during USB global suspend but
automatically cleared by the controller during remote wakeup or
during resume. Setting this bit back while restoring context
causes undesired behaviour. i.e. Babble interrupt is generated
and USB is broken.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disables PING on status phase of control transfer.
PING token is not mandatory in status phase of control transfer
and so some high speed USB devices don't support it. If such devices
are connected to MUSB then they would not respond to PING token
causing delayed or failed enumeration.
[Roger Q] Fixes enumeration issues with some Super-Speed USB hubs
e.g. Dlink DUB-1340
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of ISOCH transfers the hrtimer workaround for the hardware issue
is not very reliable. Instead of checking musb_is_tx_fifo_empty() in hrtimer
routine, schedule a completion work and check the same in completion work.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable CPPI to handle high bandwidth transfers, especially to support
webcam captures. Use a single bd to get the whole of the data in case of
high bandwidth transfers.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Enable the isochrounous IN handling for AM335x HOST.
Reprogram CPPI to receive consecutive ISOCH frames in the same URB.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=N4//
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v3.14 merge window
This pull request is quite extensive, containing
105 non-merge commits. Because of that, we describe
the changes in sections below:
New drivers:
- Keystone PHY driver and DWC3 Glue Layer
- Aeroflex Gaisler GRUSBDC
- Tahvo PHY driver for N770
- JZ4740 MUSB gluer Layer
- Broadcom PHY Driver
Important new features:
- MUSB DSPS learned about suspend/resume
- New quirk_ep_out_aligned_size flag added to struct usb_gadget
- DWC3 initializes the new quirk flag so gadget drivers can use it.
- AM335x PHY Driver learns about remote wakeup
- Renesas USBHS now requests DMA Engine only once
- s3c-hsotg is now re-used on Broadcom devices
- USB PHY layer now makes sure to initialize the notifier for all
drivers
- omap-control learned about TI's new AM437x devices
- few other usb gadget/function drivers learned about the new
configfs-based binding.
Misc Fixes and Clean Ups:
- Several sparse fixes all over the place
- Removal of redundant of_match_ptr()
- r-car gen2 phy now uses usb_add_phy_dev()
- removal of DEFINE_PCI_DEVICE_TABLE() from a few drivers
- conversion to clk_prepare/clk_unprepare on r8a66597-udc
- some randconfig errors and build warnings were fixed
- removal of unnecessary lock on dwc3-omap.c
Signed-of-by: Felipe Balbi <balbi@ti.com>
Removing the check to usb_disable() before registering the platform
driver allows to build this driver when !USB && USB_GADGET, to be
used in gadget-only mode.
Also, use module_platform_driver() to register the platform driver.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This USB controller can work in as host-only, gadget-only or dual-role
modes. Rework the dependency on the USB and USB_GADGET configs in order
to allow building the driver when !USB or !USG_GADGET.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a fall-out from "usb: musb: finish suspend/reset work
independently from musb_hub_control()" that I missed because the
MUSB_POWER register does not have the MUSB_POWER_SUSPENDM bit set on
AM335x platforms; hence the code path was not travelled in my tests.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb_port_reset() takes a 2nd arguments. This didn't hit us yet because
this function was never called externally prior to the musb_hub_control
cleanup patch.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
JZ4740 USB Device Controller is not OTG compatible and does not have
DEVCTL register in silicon.
During ethernet-over-usb transactions, on reset, musb driver tries to
read from DEVCTL and consequently sets device as host (A-Device)
instead of peripheral (B-Device), which makes it a composite device to
the USB gadget driver.
This induces a kernel panic during power down where the USB gadget
driver does a null pointer dereference when trying to access the
composite device configuration.
On reset, do not rely on DEVCTL value for setting gadget peripheral
mode. Use is_otg flag instead to set it to B-Device.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for Ingenic JZ4740 USB Device Controller through a
specific musb glue layer.
JZ4740 UDC not being OTG compatible and missing some hardware
registers, this musb glue layer is written from scratch to be used in
gadget mode only and take silicon design specifics into account.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently, resume and reset is completed when the USB core calls back
the root hub, asking for the port's state. This results in
unpredictable timing of state assertion, which in turn renders some
USB devices unusable after resume.
Fix this by moving the logic to end the reset and suspend state out of
musb_hub_control() into separate functions called from delayed workers.
GetPortStatus only reports the current state now, without taking any
real action.
The rh_timeout variable is kept in order to define a minimum time gap
between reset and resume only.
FWIW, in my case, a Verbatim "STORE N GO" mass storage device won't
resume cleanly without this patch.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQEcBAABAgAGBQJSrhGrAAoJEHm+PkMAQRiGsNoH/jIK3CsQ2lbW7yRLXmfgtbzz
i2Kep6D4SDvmaLpLYOVC8xNYTiE8jtTbSXHomwP5wMZ63MQDhBfnEWsEWqeZ9+D9
3Q46p0QWuoBgYu2VGkoxTfygkT6hhSpwWIi3SeImbY4fg57OHiUil/+YGhORM4Qc
K4549OCTY3sIrgmWL77gzqjRUo+pQ4C73NKqZ3+5nlOmYBZC1yugk8mFwEpQkwhK
4NRNU760Fo+XIht/bINqRiPMddzC15p0mxvJy3cDW8bZa1tFSS9SB7AQUULBbcHL
+2dFlFOEb5SV1sNiNPrJ0W+h2qUh2e7kPB0F8epaBppgbwVdyQoC2u4uuLV2ZN0=
=lI2r
-----END PGP SIGNATURE-----
Merge tag 'v3.13-rc4' into next
Linux 3.13-rc4
* tag 'v3.13-rc4': (1001 commits)
Linux 3.13-rc4
null_blk: mem garbage on NUMA systems during init
radeon_pm: fix oops in hwmon_attributes_visible() and radeon_hwmon_show_temp_thresh()
Revert "selinux: consider filesystem subtype in policies"
igb: Fix for issue where values could be too high for udelay function.
i40e: fix null dereference
ARM: fix asm/memory.h build error
dm array: fix a reference counting bug in shadow_ablock
dm space map: disallow decrementing a reference count below zero
mm: memcg: do not allow task about to OOM kill to bypass the limit
mm: memcg: fix race condition between memcg teardown and swapin
thp: move preallocated PTE page table on move_huge_pmd()
mfd/rtc: s5m: fix register updating by adding regmap for RTC
rtc: s5m: enable IRQ wake during suspend
rtc: s5m: limit endless loop waiting for register update
rtc: s5m: fix unsuccesful IRQ request during probe
drivers/rtc/rtc-s5m.c: fix info->rtc assignment
include/linux/kernel.h: make might_fault() a nop for !MMU
drivers/rtc/rtc-at91rm9200.c: correct alarm over day/month wrap
procfs: also fix proc_reg_get_unmapped_area() for !MMU case
...
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds "maxpacket_limit" to struct usb_ep. This field contains
maximum value of maxpacket supported by driver, and is set in driver probe.
This value should be used by autoconfig() function, because value of field
"maxpacket" is set to value from endpoint descriptor when endpoint becomes
enabled. So when autoconfig() function will be called again for this endpoint,
"maxpacket" value will contain wMaxPacketSize from descriptior instead of
maximum packet size for this endpoint.
For this reason this patch adds new field "maxpacket_limit" which contains
value of maximum packet size (which defines maximum endpoint capabilities).
This value is used in ep_matches() function used by autoconfig().
Value of "maxpacket_limit" should be set in UDC driver probe function, using
usb_ep_set_maxpacket_limit() function, defined in gadget.h. This function
set choosen value to both "maxpacket_limit" and "maxpacket" fields.
This patch modifies UDC drivers by adding support for maxpacket_limit.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Individual controller driver has different requirement for wakeup
setting, so move it from core to itself. In order to align with
current etting the default wakeup setting is enabled (except for
chipidea host).
Pass compile test with below commands:
make O=outout/all allmodconfig
make -j$CPU_NUM O=outout/all drivers/usb
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only start the otg_timer in dual role mode; otherwise in peripheral mode
when musb is disconnected from the host port, otg_timer starts and
continuously toggles the session, which causes VBUS pulse.
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dsps platform needs to save save some registers at suspend time and
restore them after resume. This patch adds a struct for these registers,
and also lets the musb core know that the core registers need to be
saved as well.
We also have to explicitly de-assert the port reset upon resume on this
platform, but musb_port_reset() should not be called from glue layers.
Hence, introduce a flag in struct musb_hdrc_config for this.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
rx_mode and tx_mode need to be read at suspend time and restored on
resume for dsps platforms. So add it to the wrapper struct first, and
initialize the values.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make musb_port_suspend() externally available, and call it when to host
goes into suspend. This allows the core to go into suspend while a
device is connected.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It appears not all platforms featuring a musb core need to save the musb
core registers at suspend time and restore them on resume.
The dsps platform does, however, and because it shouldn't cause any
trouble on other platforms, do it unconditionally for all of them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this will let us support broken designs such
as AM335x EVM SK where ID pin isn't routed
anywhere on a host port.
With this we can toggle internal IDDIG signal
and make sure MUSB goes into host mode as
necessary.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since commit c5340bd14 ("usb: musb: cancel work on removal") the workqueue
is cancelled but then if we bail out before the workqueue is setup we
get this:
|INFO: trying to register non-static key.
|the code is fine but needs lockdep annotation.
|turning off the locking correctness validator.
|CPU: 0 PID: 708 Comm: modprobe Not tainted 3.12.0+ #435
|[<c00867bc>] (lock_acquire+0xf0/0x108) from [<c00529d0>] (flush_work+0x38/0x2ec)
|[<c00529d0>] (flush_work+0x38/0x2ec) from [<c0052d24>] (__cancel_work_timer+0xa0/0x134)
|[<c0052d24>] (__cancel_work_timer+0xa0/0x134) from [<bf0e4ae4>] (musb_free+0x40/0x60 [musb_hdrc])
|[<bf0e4ae4>] (musb_free+0x40/0x60 [musb_hdrc]) from [<bf0e5364>] (musb_probe+0x678/0xb78 [musb_hdrc])
|[<bf0e5364>] (musb_probe+0x678/0xb78 [musb_hdrc]) from [<c0294bf0>] (platform_drv_probe+0x1c/0x24)
|[<c0294bf0>] (platform_drv_probe+0x1c/0x24) from [<c0293970>] (driver_probe_device+0x90/0x224)
|[<c0293970>] (driver_probe_device+0x90/0x224) from [<c0291ef0>] (bus_for_each_drv+0x60/0x8c)
|[<c0291ef0>] (bus_for_each_drv+0x60/0x8c) from [<c02938bc>] (device_attach+0x80/0xa4)
|[<c02938bc>] (device_attach+0x80/0xa4) from [<c0292b24>] (bus_probe_device+0x88/0xac)
|[<c0292b24>] (bus_probe_device+0x88/0xac) from [<c0291490>] (device_add+0x388/0x6c8)
|[<c0291490>] (device_add+0x388/0x6c8) from [<c02952a0>] (platform_device_add+0x188/0x22c)
|[<c02952a0>] (platform_device_add+0x188/0x22c) from [<bf11ea30>] (dsps_probe+0x294/0x394 [musb_dsps])
|[<bf11ea30>] (dsps_probe+0x294/0x394 [musb_dsps]) from [<c0294bf0>] (platform_drv_probe+0x1c/0x24)
|platform musb-hdrc.1.auto: Driver musb-hdrc requests probe deferral
|musb-hdrc musb-hdrc.1.auto: musb_init_controller failed with status -517
This patch moves the init part to earlier part so it can be cleaned as
part of the fail3 label because now it is surrounded by the fail4 label.
Step two is to remove it from musb_free() and add it to the two cleanup
paths (error path and device removal) separately.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The TX-complete interrupt of the CPPI41 on AM335x fires too early.
Adding a loop and counting how long it takes until the
MUSB_TXCSR_TXPKTRDY bit is cleared I see
FS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1
|cppi41_dma_callback() 74 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1
|cppi41_dma_callback() 66 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops
avg: 110 - 150us
HS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1
|cppi41_dma_callback() 0 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1
|cppi41_dma_callback() 2 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1
|cppi41_dma_callback() 13 loops
avg: 2us
for the same test case. One loop means a udelay(1). The delay seems to
depend on the packet size. On HS the bit is always cleared for small
packet sizes while on FS it is never the case, it mostly around 110us.
This testing has been performed with g_ether (musb as device) and using BULK
transfers.
INTR transfers are way more fun: during init the gadget sends a INT
packet to the host and cppi41 says "transfer done" shortly after. The
MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host
did not try to receive it, it does so after the interface (on host side) has
been configured. Until this happens, that packet remains in musb's FIFO.
To fix this, two things are done:
- No DMA transfers for INT based endpoints. These transfer are usually
very small and rare so it is likely better to skip the DMA engine and
stuff the four bytes directly into the FIFO
- on HS we poll up to 25us and hope that bit goes away. If not we setup
a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS
the command
| ping 10.10.10.10 -c1 -s65130
creates about 44 1514bytes transfers. About 19 of them need a second
timer to complete.
Reported-by: Bin Liu <b-liu@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves most of the logic in cppi41_dma_callback() into
cppi41_trans_done() where it can be called from another function.
Instead of computing "transferred" (the number of bytes transferred in
the last transaction) in cppi41_trans_done() the member
"cppi41_channel->prog_len" is now set to 0 if the transfer as a whole
can be considered as done. If it is != 0 then the next iteration is
assumed.
This is a preparation for a workaround.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The musb driver is usable in host, gadget or dual role mode depending
on the kernel configuration.
However, the musb gadget part of the driver is enabling OTG mode
whether the driver is built for dual role or gadget only mode. This
induces a bug for gadget only USB device controllers where the kernel
tries to use Host Negotiation Protocol with such controllers, which
causes a panic.
This behaviour is now fixed by enabling OTG mode only when musb driver
is built for dual role mode.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Most of this branch consists of updates, additions and general churn of
the device tree source files in the kernel (arch/arm/boot/dts). Besides
that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board files
for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as well
- Some updates to pinctrl and other subsystems. Most of these are for
DT-enablement of the various platforms and acks have been collected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=nH67
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=LDY7
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.13
Final conversions to configfs for mass storage, acm_ms, and
multi gadgets.
MUSB should now work out of the box on AM335x-based boards
(beagle bone white and black) with DMA thanks to Sebastian's
work.
We can now enable VERBOSE_DEBUG on builds of drivers/usb/gadget/
by selecting CONFIG_USB_GADGET_VERBOSE.
s3c-hsotg got quite a few non-critical fixes but also learned
a few new tricks (isochronous transfers, multi count support).
The Marvel USB3 Controller driver got a memory leak fix.
devm_usb_get_phy() learned not to return NULL, ever.
Other than these patches, we have the usual set of cleanups
ranging from removal of unnecessary *_set_drvdata() to using
SIMPLE_DEV_PM_OPS.
Signed-of-by: Felipe Balbi <balbi@ti.com>
If everything (musb, cppi41, phy) is built-in then musb will start
without the dma engine printing only
|musb-hdrc musb-hdrc.0.auto: Falied to request rx1.
The reason for this is that the musb device structs are created & probed
before those of the cppi41 device. So the cppi41 device is probed too
late.
As a workaround for this allow the musb_cppi41 part to defer the probe
if everything is fine except for the missing DMA controller. In case of
another error we continue.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit f3ce4d5 ("usb: musb: core: call dma_controller_destroy() in the err path")
I erroneously assumed that the dma controller is not removed in the
error patch. This was wrong because it happens later via musb_free().
That means the original commit can be reverted because it is wrong or we
do this, so it is more obvious.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The patch fixes two issues in the error path cleanup:
- in MUSB_PORT_MODE_DUAL_ROLE mode, if musb_gadget_setup() fails we
never cleanup the host struct earlier allocated.
- if musb_init_debugfs() or sysfs_create_group() fails, then we never
free the host part initialization, only device part.
Cc: stable@vger.kernel.org # v3.11
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
I introduced this check here because it looked wrong in HOST only
configurions. The timer would remove that session bit and will never
come back and so there would not be another session.
Now that I played with OTG for a while I belive this workaround is
only required for the OTG mode because we have to end the session and
then we have to try to start manually.
Therefore, this patch limits this timer to the OTG only port mode so we
don't need to poll around in device only mode.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the comments, we rely on the OTG timer because the core
does not expose some important OTG details. So far this is all I
know. After playing with OTG I stumbled over a problem:
musb is recognized as a B-device without a problem. Whenever a cable is
plugged, the VBUS rises, musb recognizes this as a starting session,
sets the MUSB_DEVCTL_SESSION bit by itself and a RESET interrupt occurs,
the session starts. Good.
After a disconnect, the timer is started and re-starts itself because
it remains in B_IDLE with the BDEVICE set. I didn't figure the the
reason or the need for it. Nothing changes here except for OTG state
from B to A device if the BDEVICE bit disappears. This doesn't make much
sense to me because nothing happens after this. _IF_ we receive an
interrupt before the state change then we may act on wrong condition.
Plugging a B-device (and letting MUSB act as host) doesn't work here.
The reason seems to be that the MUSB tries to start a session, it fails
and then it removes the bit. So we never start as a host.
This patch sets the MUSB_DEVCTL_SESSION bit in the IDLE state so musb
can try to establish a session as host. After the bit is set, musb tries
to start a session and if it fails it clears the bit. Therefore it will
try over and over again until a session either as host or as device is
established.
The readout of the MUSB_DEVCTL register after the removal the
MUSB_DEVCTL_SESSION (in A_WAIT_BCON) has been removed because it did not
contain the BDEVICE bit set (in the second read) leading to A_IDLE. After
plugging a host musb assumed that it is also a host and complained about
a missing reset. However a third read of the register has has the BDEVICE
bit set so it seems that it is not stable.
This mostly what da8xx.c is doing except that we set the timer also
after A_WAIT_BCON so the session bit can be triggered.
Whit this change I was able to keep am335x-evm in OTG mode and plug in
either a HOST or a DEVICE and in a random order and the device was
recognized.
Cc: stable@vger.kernel.org # v3.11
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch moves dsps_musb_try_idle() before dsps_musb_enable() so the
declaration (of dsps_musb_try_idle() can be removed.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The timer is initialized right after musb is probed. There is actually
no need to have this timer running because _nothing_ will happen until
we have the gadget loaded. Also we need this timer only if we run in OTG
mode _and_ we need it also after the gadget has been replaced with
another one.
I've been looking at am35x.c, da8xx.c, omap2430.c, tusb6010.c. da8xx
seem to have the same problem as dsps and doing mostly the same thing.
tusb6010 seem to do something different and do some actual "idle / power
saving" work so I am not too comfortable to remove
musb_platform_try_idle() from musb_gadget_setup().
Therefore this patch does not start the timer if there is no gadget
active (which is at musb_gadget_setup() at time). In order to have the
timer active after the gadget is loaded it will be triggered from
dsps_musb_enable().
Cc: stable@vger.kernel.org # v3.11
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In commit 001dd84 ("usb: musb: start musb on the udc side, too") it was
ensured that the state engine is started also in OTG mode after a
removal / insertion of the gadget.
Unfortunately this change also introduced a bug: If the device is
configured as OTG and it connected with a remote host _without_ loading
a gadget then we bug() later (because musb->otg->gadget is not
initialized).
Initially I assumed it might be nice to have the host part of musb in
OTG mode working without having a gadget loaded. This bug and fact that
it wasn't working like this before the host/gadget split made me realize
that this was a silly idea.
This patch now introduces back the old behavior where in OTG mode the
host mode is only working after the gadget has been loaded.
Cc: stable@vger.kernel.org # v3.11
Cc: Daniel Mack <zonque@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=bqsS
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
From Tony Lindgren:
Changes needed to prepare for making omap3 device tree only:
- Always build in board-generic, and add pdata quirks and auxdata
support for it so we have all the pdata related quirks
in the same place.
- Merge of the drivers/pinctrl changes that are needed for PM
to continue working on omap3 and also needed for other omaps
eventually. The three pinctrl related patches have been acked
by Linus Walleij and are pulled into both the pinctrl tree
and this branch.
- Few defconfig related changes for drivers needed.
* tag 'omap-for-v3.13/quirk-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (523 commits)
ARM: configs: omap2plus_defconfig: enable dwc3 and dependencies
ARM: OMAP2+: Add WLAN modules and of_serial to omap2plus_defconfig
ARM: OMAP2+: Run make savedefconfig on omap2plus_defconfig to shrink it
ARM: OMAP2+: Add minimal 8250 support for GPMC
ARM: OMAP2+: Use pdata quirks for wl12xx for omap3 evm and zoom3
ARM: OMAP: Move DT wake-up event handling over to use pinctrl-single-omap
ARM: OMAP2+: Add support for auxdata
pinctrl: single: Add support for auxdata
pinctrl: single: Add support for wake-up interrupts
pinctrl: single: Prepare for supporting SoC specific features
ARM: OMAP2+: igep0020: use display init from dss-common
ARM: OMAP2+: pdata-quirks: add legacy display init for IGEPv2 board
+Linux 3.12-rc4
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This reverts commit 9b0a1de3c8.
Aaro writes:
With v3.12-rc4 I can no longer connect to N800 (OMAP2) with USB
(peripheral, g_ether).
According to git bisect this is caused by:
9b0a1de3c8 is the first bad commit
So revert this patch, as Felipe says:
It's unfortunate that tusb6010 is so messed up
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These aren't necessary after switch and if blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have am335x-evm with one port running in OTG mode. Since commit
fe4cb09 ("usb: musb: gadget: remove hcd initialization") the loaded
gadget does non pop up on the host. All I see is
|usb 4-5: new high-speed USB device number 52 using ehci-pci
|usb 4-5: device descriptor read/64, error -110
Since a later commit 2cc65fe ("usb: musb: add musb_host_setup() and
musb_host_cleanup()) the gadget shows up on the host again but only
in OTG mode (because we have the host init code running). It does not
work in device only mode.
If running in OTG mode and the gadget is removed and added back (rmmod
followed by modprobe of a gadget) then the same error is pops up on the
host side.
This patch ensures that the gadget side also executes musb_start() which
puts the chip in "connect accept" mode. With this change the device
works in OTG & device mode and the gadget can be added & removed
multiple times.
A device (if musb is in OTG mode acting as a host) is only recognized if
it is attached during module load (musb_hdrc module). After the device
unplugged and plugged again the host does not recognize it. We get a
buch of errors if musb running in OTG mode, attached to a host and no
gadget is loaded. Bah.
This is one step forward. Host & device only mode should work. I will
look at OTG later. I looked at this before commit fe4cb09 and OTG wasn't
working there perfectly so I am not sure that it is a regression :)
Cc: <stable@vger.kernel.org> # v3.11
Cc: Daniel Mack <zonque@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So I captured this:
|WARNING: CPU: 0 PID: 2078 at /home/bigeasy/work/new/TI/linux/lib/debugobjects.c:260 debug_print_object+0x94/0xc4()
|ODEBUG: free active (active state 0) object type: work_struct hint: musb_irq_work+0x0/0x38 [musb_hdrc]
|CPU: 0 PID: 2078 Comm: rmmod Not tainted 3.12.0-rc4+ #338
|[<c0014d38>] (unwind_backtrace+0x0/0xf4) from [<c001249c>] (show_stack+0x14/0x1c)
|[<c001249c>] (show_stack+0x14/0x1c) from [<c0037720>] (warn_slowpath_common+0x64/0x84)
|[<c0037720>] (warn_slowpath_common+0x64/0x84) from [<c00377d4>] (warn_slowpath_fmt+0x30/0x40)
|[<c00377d4>] (warn_slowpath_fmt+0x30/0x40) from [<c022ae90>] (debug_print_object+0x94/0xc4)
|[<c022ae90>] (debug_print_object+0x94/0xc4) from [<c022b7e0>] (debug_check_no_obj_freed+0x1c0/0x228)
|[<c022b7e0>] (debug_check_no_obj_freed+0x1c0/0x228) from [<c00f1f38>] (kfree+0xf8/0x228)
|[<c00f1f38>] (kfree+0xf8/0x228) from [<c02921c4>] (release_nodes+0x1a8/0x248)
|[<c02921c4>] (release_nodes+0x1a8/0x248) from [<c028f70c>] (__device_release_driver+0x98/0xf0)
|[<c028f70c>] (__device_release_driver+0x98/0xf0) from [<c028f840>] (device_release_driver+0x24/0x34)
|[<c028f840>] (device_release_driver+0x24/0x34) from [<c028ebe8>] (bus_remove_device+0x148/0x15c)
|[<c028ebe8>] (bus_remove_device+0x148/0x15c) from [<c028d120>] (device_del+0x104/0x1c0)
|[<c028d120>] (device_del+0x104/0x1c0) from [<c02911e4>] (platform_device_del+0x18/0xac)
|[<c02911e4>] (platform_device_del+0x18/0xac) from [<c029179c>] (platform_device_unregister+0xc/0x18)
|[<c029179c>] (platform_device_unregister+0xc/0x18) from [<bf1902fc>] (dsps_remove+0x20/0x4c [musb_dsps])
|[<bf1902fc>] (dsps_remove+0x20/0x4c [musb_dsps]) from [<c0290d7c>] (platform_drv_remove+0x1c/0x24)
|[<c0290d7c>] (platform_drv_remove+0x1c/0x24) from [<c028f704>] (__device_release_driver+0x90/0xf0)
|[<c028f704>] (__device_release_driver+0x90/0xf0) from [<c028f818>] (driver_detach+0xb4/0xb8)
|[<c028f818>] (driver_detach+0xb4/0xb8) from [<c028e6e8>] (bus_remove_driver+0x98/0xec)
|[<c028e6e8>] (bus_remove_driver+0x98/0xec) from [<c008fc70>] (SyS_delete_module+0x1e0/0x24c)
|[<c008fc70>] (SyS_delete_module+0x1e0/0x24c) from [<c000e680>] (ret_fast_syscall+0x0/0x48)
|---[ end trace d79045419a3e51ec ]---
The workqueue is only scheduled from the ep0 and never canceled in case
the musb is removed before the work has a chance to run.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
omap_get_control_dev() is being deprecated as it doesn't support
multiple instances. As control device is present only from OMAP4
onwards which supports DT only, we use phandles to get the
reference to the control device.
Also get rid of "ti,has-mailbox" property as it is redundant and
we can determine that from whether "ctrl-module" property is present
or not. Get rid of has_mailbox from musb_hdrc_platform_data as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This removes the DEV_PM_OPS macro and brings this file in line with the
other musb platform drivers.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes bfin_pm_ops const and will stub the struct out in case
CONFIG_PM_SLEEP is not set.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This makes am35x_pm_ops const and will stub the struct out in case
CONFIG_PM_SLEEP is not set.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Cc: Ravi B <ravibabu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After commit 09fc7d22b0 (usb: musb: fix incorrect
usage of resource pointer), CPPI DMA driver on DaVinci DM6467 can't detect its
dedicated IRQ and so the MUSB IRQ is erroneously used instead. This is because
only 2 resources are passed to the MUSB driver from the DaVinci glue layer, so
fix this by always copying 3 resources (it's safe since a placeholder for the
3rd resource is always there) and passing 'pdev->num_resources' instead of the
size of musb_resources[] to platform_device_add_resources().
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use platform_device_register_full() for those drivers which can, to
avoid messing directly with DMA masks. This can only be done when
the driver does not need to access the allocated musb platform device
from within its callbacks, which may be called during the musb
device probing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
More power supply drivers depends on vbus events and without it they not
working. Power supply drivers using usb_register_notifier, so to deliver
events it is needed to call atomic_notifier_call_chain.
So without atomic notifier power supply driver isp1704 not retrieving
vbus status and reporting bogus values to userspace and also to board
platform data functions. Without proper data charger drivers trying to
charge battery also when charger is disconnected or do not start charging
when wallcharger connects.
Atomic notifier in musb driver was used before v3.5 and was replaced with
omap mailbox. This patch adding atomic_notifier_call_chain call from
function omap_musb_set_mailbox.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Kconfig help text is talking about the U5500 which is no
longer supported by the kernel. Name the help text after the
config symbol which is more correct.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This went unnoticed in durin the merge window:
The dsps driver creates a child device for the musb core driver _and_
attaches the of_node to it so devm_usb_get_phy_by_phandle() grabs the
correct phy and attaches the devm resources to the proper device. We
could also use the parent device but then devm would attach the
resource to the wrong device and it would be destroyed once the parent
device is gone - not the device that is used by the musb core driver.
If the phy is now not available then dsps_musb_init() /
devm_usb_get_phy_by_phandle() returns with EPROBE_DEFER. Since the
of_node is attached it tries OF drivers as well and matches the driver
against DSPS. That one creates a new child device for the musb core
driver which gets probed immediately.
The whole thing repeats itself until the stack overflows.
I belive the same problem exists in ux500 glue code (since 313bdb11
("usb: musb: ux500: add device tree probing support") but the drivers are
now probed in the right order so they don't see it.
The problem is that the dsps driver gets bound to the musb-child device
due to the same of_node / matching binding. I don't really agree with
having yet another child node in DT to fix this. Ideally we would have
musb core driver with DT bindings and according to the binding we would
select the few extra hacks / gleue layer.
Therefore I suggest the driver to reject the musb-core device.
Cc: Lee Jones <lee.jones@linaro.org>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the generic PHY framework API to get the PHY. The usb_phy_set_resume
and usb_phy_set_suspend is replaced with power_on and
power_off to align with the new PHY framework.
musb->xceiv can't be removed as of now because musb core uses xceiv.state and
xceiv.otg. Once there is a separate state machine to handle otg, these can be
moved out of xceiv and then we can start using the generic PHY framework.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we supply a con_id then the clock framework will search for that name
in MUSB's Device Tree node for the 'clock-names' property. If it's absent
the clock request will fail. However, if we don't supply the con_id then
clk_get() will call into clk_sys() which will use the device name to
search for the appropriate clock, which is much more natural than forcing
'usb'.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In gadget mode, musb->is_active should be set only when connected to the
host. musb_g_reset() already takes care of it.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Right after the musb_hdrc driver is loaded, the otg default state
is a_idle, and Mode=Host, which are set by musb_host_setup().
This causes the following kernel message during musb gadget
enumeration.
CAUTION: musb: Babble Interrupt Occurred
This patch sets the otg default state to b_idle, and its Mode to
Peripheral.
It has been validated on TI AM335x GP EVM USB0 port with g_zero.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
