Use snd_hda_jack_detect() again for jack-sensing.
The triggering problem can be worked around with codec->no_trigger_sense
flag now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pin config provided by BIOS have some problems:
0x0221401f: [Jack] HP Out at Ext Front <-- other association and sequence
0x02a19020: [Jack] Mic at Ext Front <-- other association
0x01113014: [Jack] Speaker at Ext Rear <-- line out (not speaker)
0x01114010: [Jack] Speaker at Ext Rear <-- line out
0x01a19030: [Jack] Mic at Ext Rear <-- other association
0x01111012: [Jack] Speaker at Ext Rear <-- line out
0x01116011: [Jack] Speaker at Ext Rear <-- line out
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x40f000f0: [N/A] Other at Ext N/A
0x01451140: [Jack] SPDIF Out at Ext Rear
0x40f000f0: [N/A] Other at Ext N/A
just overwrite it.
Signed-off-by: Alexey Fisher <bug-track@fisher-privat.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch fixes an error in processing of the HP BIOS configuration to enable
GPIO based mute LED indicator control. That error causes driver to enable
such control on all HP systems with the 92HD75 IDT codecs and results in
unnecessary toggling of the GPIO on mute control manipulation.
It also adds support of the future HP BIOS configuration extension for the
named control. New configuration string has a format HP_Mute_LED_P_G
where P can be 0 or 1 and defines mute LED GPIO control state (low/high)
that corresponds to the NOT muted state of the master volume
and G is the index of the GPIO to use (0..9)
Lastly, it adds more systems to the support of the audio implementation
as found on HP B-series systems
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
STAC/IDT codecs seem to behave weird when SET_PIN_SENSE verb is issued
before reading the jack-detection although the TRIG_REQ pin capability
is given by the hardware.
Since snd_hda_jack_detect() issues the SET_PIN_SENSE verb simply judging
from the pincap, we have to revert the change in the commit
d56757abc1
ALSA: hda - Replace the rest of jack-detections with snd_hda_jack_detect()
to plain GET_PIN_SENSE verb without triggering.
Reported-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The mute-LED isn't synchronized with the actual mute state on some
HP laptops with IDT 92HD83xxx codecs. A similar hack using
check_power_status callback is added for this codec, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The dual-headphone mode with STAC/IDT codecs is useful only for machines
that have two (or more) built-in headphones.
But, some HP laptops give multiple headphone pin configs, one for the
built-in and another for the separate (likely a docking station) one.
This results in a missing speaker volume control.
This patch adds more check for the dual-headphone mode to avoid this
problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds support for dynamically created controls to proc codec file
(Control: lines).
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is an initial patch to show universal control<->NID assigment in
proc codec file. The change helps to debug codec related problems.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Original implementation was keeping registered input device for SND_BEEP
and SND_TONE events all time. This patch changes this behaviour:
If digital PC Beep is turned off using universal control switch,
the input device is unregistered.
Explanation: The kd_mksound() send SND_BEEP and SND_TONE only to last
registered device acceping those events. It means that the HDA Intel
audio driver blocks also the internal PC Speaker device (pcspkr.c
driver) even if the HDA Beep is muted. The user can easy disable
all beeps using 'setterm -blength 0' or 'xset b off' command.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add reboot notifier to each codec so that it can do some workarounds
needed for reboot.
So far, patch_sigmatel.c calls its shutup routine for avoiding noises
at reboot on some HP machines.
References: Novell bnc#544779
http://bugzilla.novell.com/show_bug.cgi?id=544779
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some laptops cause annoying clicks or noises at shutdown/reboot since
the speaker pin is set still high. Apply the same procedure used for
the suspend to avoid such clicks/noises for freeing the codec, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Function hp_bseries_system() is always used, outside of
CONFIG_ boundaries/controls, so move it.
sound/pci/hda/patch_sigmatel.c:5458: error: implicit declaration of function 'hp_bseries_system'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To avoid confusion in control names for the standard analog PC Beep generator
using a small Internal PC Speaker, rename all related "PC Speaker" and "PC
Beep" controls to "Beep" only. This name is more universal and can be also
used on more platforms without confusion.
Introduce also "Internal Speaker" in ControlNames.txt for systems with
full-featured build-in internal speaker.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch enables GPIO to control mute LED indicator on the HP systems
with the special string in BIOS and applies it with the correct polarity on
HP B-series systems.
It also restores configuration of the pin intended as the second Headphone
on HP B-series systems but configured as something else in the BIOS to
pass MS DTM.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The volume-knob widget needs to be set with 0x7f instead of 0xff
for Dell laptops with STAC9228 codec, too, like the previous commit.
Reference: Novell bnc#545013
http://bugzilla.novell.com/show_bug.cgi?id=545013
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On FSC laptops, the sound gets muted gradually when the volume is chnaged.
This is due to the wrong volume-knob widget setup. The delta bit (bit 7)
shouldn't be set for these devices.
This patch adds a new quirk to set the value 0x7f to the widget 0x24
instead of 0xff.
Reference: Novell bnc#546006
http://bugzilla.novell.com/show_bug.cgi?id=546006
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the auto-mic switching between an analog and a digital mic is
needed with IDT codecs, the current driver doesn't reset the connection
of the digital mux.
This patch fixes the behavior by checking both mux connections properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The pin setup for Dell S14 quirk is rather wrong for the latest driver.
Fixed pin 0x0a, 0x0b, 0x0d and 0x0f.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove unnecessary (and buggy) init sequences left for IDT92HD83*
codecs in the previous fixes. The DACs are now dynamically connected,
thus shouldn't be set statically in init verbs. Also, the mono_nid
is detected dynamically, thus shouldn't be set staticaly, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the quirk entry for HP dv6. Also add a workaround for the headphone
detection by setting hp_detect=1 beforehand. Without this, the driver
won't do auto-muting because BIOS doesn't give any HP pin but only a
line-out pin.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's possible that hp_detect is set even though no headphone pin is
detected. The driver issues, however, an unsol event only to hp_pins[0],
which can be invalid.
This patch adds the check of the valid pin to send an unsol event
at initialization and resume callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
IDT92HD73xx and STAC927x codecs use GPIO0 bit as EAPD on many machines.
However, currently we don't set it unless the model is specified just
for safety reason. But, most machines do need this bit, so this safety
handling is rather annoying.
This patch enables GPIO0 setup as default for them. Many HP / Dell
laptops should work even without model override with this change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added the quirk for Alienware M17x with IDT 92HD73* codec chip.
It has two HP and one line-out jack, one mic jack, a built-in
speaker and a built-in mic.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to the previous fix of input source for IDT92HD73xx, the amp mux
and amp vol stuff became unused. Let's rip off dead codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix the mux_nids to select directly the input source instead of mux
mixers so that it works with the current mux enum handler for IDT
92HD73xx codecs.
Also, clean up useless / unnecessary mixer controls and init verbs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the digital mic capture volume wasn't created. This is because
IDT codecs have output amps for digital mics, not input amps, while
input amps should be used for other analog pins. Thus the automatic
capture volume creation should check both directions for digital mics.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The BIOS pin configs are in fact correct and shall not be overwritten.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous fix removed the definition of num_adc_nids wrongly, and
this resulted in the missing input-source control. Now readded again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few improvements for IDT 92HD83xxx codec pareser:
- Remove unused / deprecated mixer-amp controls
- Handle d-mics as normal inputs since this codec has no separate
MUXes for analog and digital
- Don't create duplicated controls for capture volumes with Mux
capture volumes
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable line-out detection for IDT/STAC codecs only when speaker pins
exist. In some cases, the speaker itself is identified as line-out,
and this confuses the situation. Only the extra line-outs should do
auto-muting.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The previous auto-mic patch for STAC/IDT codecs causes the Oops on
machines without digital mic pins. This patch fixes the problem.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the line-out jack is plugged/unplugged, the driver needs to check
the headphone plug, not only the line-out jack itself. Otherwise the
headphone or the speaker may be wrongly muted/unmuted.
As a result, both STAC_HP_EVENT and STAC_LO_EVENT need to call the
same function, stac92xx_hp_detect().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit fefd67f31e
ALSA: hda - Add line-out jack detection on IDT/STAC codecs
enabled wrong pins for jack detections. Fixed to the correct ones.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit 24918b61b5 statically changes
the model from dell-bios to dell-3stack to solve the sound decreasing
regression (http://lkml.org/lkml/2008/9/12/203), however it leads to another
problem that the 2nd headphone jack doesn't work
(https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3987). So I think
the commit 249**2dc is just a workaround. I would like to give a true solution
here.
The datasheet for STAC9228 says, GPIO2 is the same pin as VOL DOWN, and
the EAPD pin is GPIO0. This is why the sound decreases if we set EAPD as
GPIO2. This patch changes EAPD to GPIO0 to solve the problem.
Signed-off-by: Chengu Wang <wangchengu@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the automatic mute of speakers via line-out jack plugging on
STAC/IDT codecs. The feature is enabled when the HP detect is present.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
STAC/IDT codecs provide both "Input Source" and "Digital Input Source"
controls to choose the analog input source and the digital input source.
But this is far user-unfriendly.
This patch merges the input source selections into one "Input Source"
control. To have separate digital and analog input source controls,
you can pass "separate_dmux = 1 " hint string.
At the same time, this patch gets rid of analog mixer stuff that was
already disabled in previous patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
