Here is the big set of char/misc and other small driver subsystem
changes for 6.7-rc1. Included in here are:
- IIO subsystem driver updates and additions (largest part of this
pull request)
- FPGA subsystem driver updates
- Counter subsystem driver updates
- ICC subsystem driver updates
- extcon subsystem driver updates
- mei driver updates and additions
- nvmem subsystem driver updates and additions
- comedi subsystem dependency fixes
- parport driver fixups
- cdx subsystem driver and core updates
- splice support for /dev/zero and /dev/full
- other smaller driver cleanups
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCZUTSzg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylH3QCfbZuG8MiglEZUd4slRLUNqcRQ5tQAn1yKpDFo
l3KLkxo1UTLMXbJBWe+b
=gafK
-----END PGP SIGNATURE-----
Merge tag 'char-misc-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
changes for 6.7-rc1. Included in here are:
- IIO subsystem driver updates and additions (largest part of this
pull request)
- FPGA subsystem driver updates
- Counter subsystem driver updates
- ICC subsystem driver updates
- extcon subsystem driver updates
- mei driver updates and additions
- nvmem subsystem driver updates and additions
- comedi subsystem dependency fixes
- parport driver fixups
- cdx subsystem driver and core updates
- splice support for /dev/zero and /dev/full
- other smaller driver cleanups
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (326 commits)
cdx: add sysfs for subsystem, class and revision
cdx: add sysfs for bus reset
cdx: add support for bus enable and disable
cdx: Register cdx bus as a device on cdx subsystem
cdx: Create symbol namespaces for cdx subsystem
cdx: Introduce lock to protect controller ops
cdx: Remove cdx controller list from cdx bus system
dts: ti: k3-am625-beagleplay: Add beaglecc1352
greybus: Add BeaglePlay Linux Driver
dt-bindings: net: Add ti,cc1352p7
dt-bindings: eeprom: at24: allow NVMEM cells based on old syntax
dt-bindings: nvmem: SID: allow NVMEM cells based on old syntax
Revert "nvmem: add new config option"
MAINTAINERS: coresight: Add missing Coresight files
misc: pci_endpoint_test: Add deviceID for J721S2 PCIe EP device support
firmware: xilinx: Move EXPORT_SYMBOL_GPL next to zynqmp_pm_feature definition
uacce: make uacce_class constant
ocxl: make ocxl_class constant
cxl: make cxl_class constant
misc: phantom: make phantom_class constant
...
Particularly great to see a resolver driver move out of staging via a
massive set of changes. Only took 13 years :)
One small patch added then reverted due to a report of test breakage
(ashai-kasei,ak8975: Drop deprecated enums.)
An immutable branch was used for some hid-senors changes in case
there was a need to take them into the HID tree as well.
New device support
-----------------
adi,hmc425a
- Add support for HMC540SLP3E broadband 4-bit digital attenuator.
kionix,kx022a
- Add support for the kx132-1211 accelerometer. Require significant
driver rework to enable this including add a chip type specific
structure to deal with the chip differences.
- Add support for the kx132acr-lbz accelerometer (subset of the kx022a
feature set).
lltc,ltc2309
- New driver for this 8 channel ADC.
microchip,mcp3911
- Add support for rest of mcp391x family of ADCs (there are various
differences beyond simple channel count variation.
Series includes some general driver cleanup.
microchip,mcp3564
- New driver for MCP3461, MCP3462, MCP3464, MCP3541, MCP3562, MCP3564
and their R variants of 16/24bit ADCs. A few minor fixed followed.
rohm,bu1390
- New driver for this pressure sensor.
Staging graduation
------------------
adi,ad1210 (after 13 or so years :)
- More or less a complete (step-wise) rewrite of this resolver driver
to bring it up to date with modern IIO standards. The fault signal
handling mapping to event channels was particularly complex and
significant part of the changes.
Features
--------
iio-core
- Add chromacity and color temperature channel types.
adi,ad7192
- Oversampling ratio control (called fast settling in datasheet).
adi,adis16475
- Add core support and then driver support for delta angle and delta
velocity channels. These are intended for summation to establish
angle and velocity changes over larger timescales. Fix was
needed for alignment after the temperature channel. Further fix
reduced set of devices for which the buffer support was applicable
as seems burst reads don't cover these on all devices.
hid-sensors-als
- Chromacity and color temperatures support including in amd sfh.
stx104
- Add support for counter subsystem to this multipurpose device.
ti,twl6030
- Add missing device tree binding description.
Clean up and minor fixes.
------------------------
treewide
- Drop some unused declarations across IIO.
- Make more use of device_get_match_data() instead of OF specific
approaches.
Similar cleanup to sets of drivers.
- Stop platform remove callbacks returning anything by using the
temporary remove_new() callback.
- Use i2c_get_match_data() to cope nicely with all types of ID table
entry.
- Use device_get_match_data() for various platform device to cope
with more types of firmware.
- Convert from enum to pointer in ID tables allowing use of
i2c_get_match_data().
- Fix sorting on some ID tables.
- Include specific string helper headers rather than simply string_helpers.h
docs
- Better description of the ordering requirements etc for
available_scan_masks.
tools
- Handle alignment of mixed sizes where the last element isn't the biggest
correctly. Seems that doesn't happen often!
adi,ad2s1210
- Lots of work from David Lechner on this driver including a few fixes
that are going with the rework to avoid slowing that down.
adi,ad4310
- Replace deprecated devm_clk_register()
adi,ad74413r
- Bring the channel function setting inline with the datasheet.
adi,ad7192
- Change to FIELD_PREP(), FIELD_GET().
- Calculate f_order from the sinc filter and chop filter states.
- Move more per chip config into data in struct ad7192_chip_info
- Cleanup unused parameter in channel macros.
adi,adf4350
- Make use of devm_* to simplify error handling for many of the setup
calls in probe() / tear down in remove() and error paths. Some more
work to be done on this one.
- Use dev_err_probe() for errors in probe() callback.
adi,adf4413
- Typo in function name prefix.
adi,adxl345
- Add channel scale to the chip type specific structure and drop
using a type field previously used for indirection.
asahi,ak8985
- Fix a mismatch introduced when switching from enum->pointers
in the match tables.
amlogic,meson
- Expand error logging during probe.
invensense,mpu6050
- Support level-shifter control. Whilst no one is sure exactly what this
is doing it is needed for some old boards.
- Document mount-matrix dt-binding.
mediatek,mt6577
- Use devm_clk_get_enabled() to replace open coded version and move
everything over to being device managed. Drop now empty remove()
callback. Fix follows to put the drvdata back.
- Use dev_err_probe() for error reporting in probe() callback.
memsic,mxc4005
- Add of_match_table.
microchip,mcp4725
- Move various chip specific data from being looked up by chip ID to
data in the chip type specific structure.
silicon-labs,si7005
- Add of_match_table and entry in trivial-devices.yaml
st,lsm6dsx
- Add missing mount-matrix dt binding documentation.
st,spear
- Use devm_clk_get_enabled() and some other devm calls to move everything
over to being device managed. Drop now empty remove() callback.
- Use dev_err_probe() to better handled deferred probing and tidy up
error reporting in probe() callback.
st,stm32-adc
- Add a bit of additional checking in probe() to protect against a NULL
pointer (no known path to trigger it today).
- Replace deprecated strncpy()
ti,ads1015
- Allow for edge triggers.
- Document interrupt in dt-bindings.
-----BEGIN PGP SIGNATURE-----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=wth0
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.7a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO: 1st set of new device support, features and cleanup for 6.7
Particularly great to see a resolver driver move out of staging via a
massive set of changes. Only took 13 years :)
One small patch added then reverted due to a report of test breakage
(ashai-kasei,ak8975: Drop deprecated enums.)
An immutable branch was used for some hid-senors changes in case
there was a need to take them into the HID tree as well.
New device support
-----------------
adi,hmc425a
- Add support for HMC540SLP3E broadband 4-bit digital attenuator.
kionix,kx022a
- Add support for the kx132-1211 accelerometer. Require significant
driver rework to enable this including add a chip type specific
structure to deal with the chip differences.
- Add support for the kx132acr-lbz accelerometer (subset of the kx022a
feature set).
lltc,ltc2309
- New driver for this 8 channel ADC.
microchip,mcp3911
- Add support for rest of mcp391x family of ADCs (there are various
differences beyond simple channel count variation.
Series includes some general driver cleanup.
microchip,mcp3564
- New driver for MCP3461, MCP3462, MCP3464, MCP3541, MCP3562, MCP3564
and their R variants of 16/24bit ADCs. A few minor fixed followed.
rohm,bu1390
- New driver for this pressure sensor.
Staging graduation
------------------
adi,ad1210 (after 13 or so years :)
- More or less a complete (step-wise) rewrite of this resolver driver
to bring it up to date with modern IIO standards. The fault signal
handling mapping to event channels was particularly complex and
significant part of the changes.
Features
--------
iio-core
- Add chromacity and color temperature channel types.
adi,ad7192
- Oversampling ratio control (called fast settling in datasheet).
adi,adis16475
- Add core support and then driver support for delta angle and delta
velocity channels. These are intended for summation to establish
angle and velocity changes over larger timescales. Fix was
needed for alignment after the temperature channel. Further fix
reduced set of devices for which the buffer support was applicable
as seems burst reads don't cover these on all devices.
hid-sensors-als
- Chromacity and color temperatures support including in amd sfh.
stx104
- Add support for counter subsystem to this multipurpose device.
ti,twl6030
- Add missing device tree binding description.
Clean up and minor fixes.
------------------------
treewide
- Drop some unused declarations across IIO.
- Make more use of device_get_match_data() instead of OF specific
approaches.
Similar cleanup to sets of drivers.
- Stop platform remove callbacks returning anything by using the
temporary remove_new() callback.
- Use i2c_get_match_data() to cope nicely with all types of ID table
entry.
- Use device_get_match_data() for various platform device to cope
with more types of firmware.
- Convert from enum to pointer in ID tables allowing use of
i2c_get_match_data().
- Fix sorting on some ID tables.
- Include specific string helper headers rather than simply string_helpers.h
docs
- Better description of the ordering requirements etc for
available_scan_masks.
tools
- Handle alignment of mixed sizes where the last element isn't the biggest
correctly. Seems that doesn't happen often!
adi,ad2s1210
- Lots of work from David Lechner on this driver including a few fixes
that are going with the rework to avoid slowing that down.
adi,ad4310
- Replace deprecated devm_clk_register()
adi,ad74413r
- Bring the channel function setting inline with the datasheet.
adi,ad7192
- Change to FIELD_PREP(), FIELD_GET().
- Calculate f_order from the sinc filter and chop filter states.
- Move more per chip config into data in struct ad7192_chip_info
- Cleanup unused parameter in channel macros.
adi,adf4350
- Make use of devm_* to simplify error handling for many of the setup
calls in probe() / tear down in remove() and error paths. Some more
work to be done on this one.
- Use dev_err_probe() for errors in probe() callback.
adi,adf4413
- Typo in function name prefix.
adi,adxl345
- Add channel scale to the chip type specific structure and drop
using a type field previously used for indirection.
asahi,ak8985
- Fix a mismatch introduced when switching from enum->pointers
in the match tables.
amlogic,meson
- Expand error logging during probe.
invensense,mpu6050
- Support level-shifter control. Whilst no one is sure exactly what this
is doing it is needed for some old boards.
- Document mount-matrix dt-binding.
mediatek,mt6577
- Use devm_clk_get_enabled() to replace open coded version and move
everything over to being device managed. Drop now empty remove()
callback. Fix follows to put the drvdata back.
- Use dev_err_probe() for error reporting in probe() callback.
memsic,mxc4005
- Add of_match_table.
microchip,mcp4725
- Move various chip specific data from being looked up by chip ID to
data in the chip type specific structure.
silicon-labs,si7005
- Add of_match_table and entry in trivial-devices.yaml
st,lsm6dsx
- Add missing mount-matrix dt binding documentation.
st,spear
- Use devm_clk_get_enabled() and some other devm calls to move everything
over to being device managed. Drop now empty remove() callback.
- Use dev_err_probe() to better handled deferred probing and tidy up
error reporting in probe() callback.
st,stm32-adc
- Add a bit of additional checking in probe() to protect against a NULL
pointer (no known path to trigger it today).
- Replace deprecated strncpy()
ti,ads1015
- Allow for edge triggers.
- Document interrupt in dt-bindings.
* tag 'iio-for-6.7a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (201 commits)
iio: Use device_get_match_data()
iio: adc: MCP3564: fix warn: unsigned '__x' is never less than zero.
dt-bindings: trivial-devices: add silabs,si7005
iio: si7005: Add device tree support
drivers: imu: adis16475.c: Remove scan index from delta channels
dt-bindings: iio: imu: st,lsm6dsx: add mount-matrix property
iio: resolver: ad2s1210: remove of_match_ptr()
iio: resolver: ad2s1210: remove DRV_NAME macro
iio: resolver: ad2s1210: move out of staging
staging: iio: resolver: ad2s1210: simplify code with guard(mutex)
staging: iio: resolver: ad2s1210: clear faults after soft reset
staging: iio: resolver: ad2s1210: refactor sample toggle
staging: iio: resolver: ad2s1210: remove fault attribute
staging: iio: resolver: ad2s1210: add label attribute support
staging: iio: resolver: ad2s1210: add register/fault support summary
staging: iio: resolver: ad2s1210: implement fault events
iio: event: add optional event label support
staging: iio: resolver: ad2s1210: rename DOS reset min/max attrs
staging: iio: resolver: ad2s1210: convert DOS mismatch threshold to event attr
staging: iio: resolver: ad2s1210: convert DOS overrange threshold to event attr
...
As noted by Jonathan Cameron: it is perfectly legal for a channel
to have an offset but no scale in addition to the raw interface.
The conversion will imply that scale is 1:1.
Make rescale_configure_channel() accept just scale, or just offset
to process a channel.
When a user asks for IIO_CHAN_INFO_OFFSET in rescale_read_raw()
we now have to deal with the fact that OFFSET could be present
but SCALE missing. Add code to simply scale 1:1 in this case.
Link: https://lore.kernel.org/linux-iio/CACRpkdZXBjHU4t-GVOCFxRO-AHGxKnxMeHD2s4Y4PuC29gBq6g@mail.gmail.com/
Fixes: 53ebee9499 ("iio: afe: iio-rescale: Support processed channels")
Fixes: 9decacd8b3 ("iio: afe: rescale: Fix boolean logic bug")
Reported-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20230902-iio-rescale-only-offset-v2-1-988b807754c8@linaro.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Second interrupt is needed only when touchscreen mode is used, so don't
request it unconditionally. This removes the following annoying warning
during boot:
exynos-adc 14d10000.adc: error -ENXIO: IRQ index 1 not found
Fixes: 2bb8ad9b44 ("iio: exynos-adc: add experimental touchscreen support")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20231009101412.916922-1-m.szyprowski@samsung.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20231006224440.442864-1-robh@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some devices do not support delta angle and delta velocity
burst readings, which means there should be no buffer support
for these types of channels.
A new list of channels is created which contains the delta
channels structures with the scan index equal to -1 to allow
for raw register readings, without buffer support.
This list of channels is assigned to the devices which
do not support delta angle and delta velocity burst
readings.
Fixes: 8f6bc87d67 ("iio: imu: adis16475.c: Add delta angle and delta velocity channels")
Signed-off-by: Ramona Gradinariu <ramona.gradinariu@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20231012122456.765709-2-ramona.gradinariu@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
To be consistent with the rest of iio, remove of_match_ptr(). It does
not do anything useful here.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231012-ad2s1210-mainline-v1-2-b2ee31c0e9dd@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DRV_NAME macro is only used in one place in the ad2s1210 driver and
is not really needed so let's remove it.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231012-ad2s1210-mainline-v1-1-b2ee31c0e9dd@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver was previously using offset and scale values for the
temperature sensor readings which were only valid for 7-series devices.
Add per-device-type values for offset and scale and set them appropriately
for each device type.
Note that the values used for the UltraScale family are for UltraScale+
(i.e. the SYSMONE4 primitive) using the internal reference, as that seems
to be the most common configuration and the device tree values Xilinx's
device tree generator produces don't seem to give us anything to tell us
which configuration is used. However, the differences within the UltraScale
family seem fairly minor and it's closer than using the 7-series values
instead in any case.
Fixes: c2b7720a79 ("iio: xilinx-xadc: Add basic support for Ultrascale System Monitor")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Tested-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Link: https://lore.kernel.org/r/20230915001019.2862964-3-robert.hancock@calian.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In the probe function, the driver was reading out the thresholds already
set in the core, which can be configured by the user in the Vivado tools
when the FPGA image is built. However, it later clobbered those values
with zero or maximum values. In particular, the overtemperature shutdown
threshold register was overwritten with the max value, which effectively
prevents the FPGA from shutting down when the desired threshold was
eached, potentially risking hardware damage in that case.
Remove this code to leave the preconfigured default threshold values
intact.
The code was also disabling all alarms regardless of what enable state
they were left in by the FPGA image, including the overtemperature
shutdown feature. Leave these bits in their original state so they are
not unconditionally disabled.
Fixes: bdc8cda1d0 ("iio:adc: Add Xilinx XADC driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Tested-by: O'Griofa, Conall <conall.ogriofa@amd.com>
Link: https://lore.kernel.org/r/20230915001019.2862964-2-robert.hancock@calian.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds a new optional field to struct iio_info to allow drivers to
specify a label for the event. This is useful for cases where there are
many events or the event attribute name is not descriptive enough or
where an event doesn't have any other attributes.
The implementation is based on the existing label support for channels.
So either all events of a device have a label attribute or none do.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Link: https://lore.kernel.org/r/20231005-ad2s1210-mainline-v4-12-ec00746840fc@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit a2d518fbe3 ("iio: adc: mt6577_auxadc: Simplify with device managed function")
simplified the driver with devm hooks, but wrongly states that the
platform_set_drvdata(), platform_get_drvdata() are unused after the
simplification: the driver data is infact used in .suspend() and
.resume() PM callbacks, currently producing a kernel panic.
Reintroduce the call to platform_set_drvdata() in the probe function
Fixes: a2d518fbe3 ("iio: adc: mt6577_auxadc: Simplify with device managed function")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Link: https://lore.kernel.org/r/20231010121940.159696-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add fast settling mode support for AD7193.
Add two new device specific attributes: oversampling_ratio and
oversampling_ratio_available.
For AD7193 the user can set the average factor by writing to
oversampling_ratio. The possible values are exposed when reading
oversampling_ratio_available.
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Link: https://lore.kernel.org/r/20231010124927.143343-4-alisadariana@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ms5611 driver falsely rejects lots of MS5607-02BA03-50 chips
with "PROM integrity check failed" because it doesn't accept a prom crc
value of zero as legitimate.
According to the datasheet for this chip (and the manufacturer's
application note about the PROM CRC), none of the possible values for the
CRC are excluded - but the current code in ms5611_prom_is_valid() ends with
return crc_orig != 0x0000 && crc == crc_orig
Discussed with the driver author (Tomasz Duszynski) and he indicated that
at that time (2015) he was dealing with some faulty chip samples which
returned blank data under some circumstances and/or followed example code
which indicated CRC zero being bad.
As far as I can tell this exception should not be applied anymore; We've
got a few hundred custom boards here with this chip where large numbers
of the prom have a legitimate CRC value 0, and do work fine, but which the
current driver code wrongly rejects.
Signed-off-by: Alexander Zangerl <az@breathe-safe.com>
Fixes: c0644160a8 ("iio: pressure: add support for MS5611 pressure and temperature sensor")
Link: https://lore.kernel.org/r/2535-1695168070.831792@Ze3y.dhYT.s3fx
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The avdd and the reference voltage are two different sources but the
reference voltage was assigned according to the avdd supply.
Add vref regulator structure and set the reference voltage according to
the vref supply from the devicetree.
In case vref supply is missing, reference voltage is set according to
the avdd supply for compatibility with old devicetrees.
Fixes: b581f748cc ("staging: iio: adc: ad7192: move out of staging")
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20230924152149.41884-1-alisadariana@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
After enabling/disabling interrupts on the vcnl4040 chip the als and/or
ps sensor is powered on or off depending on the interrupt enable bits.
This is made as a last step in write_event_config.
But there is no reason to do this as the runtime PM handles the power
state of the sensors. Interfering with this may impact sensor readings.
Consider the following:
1. Userspace makes sensor data reading which triggers RPM resume
(sensor powered on) and a RPM suspend timeout. The timeout is 2000ms
before RPM suspend powers the sensor off if no new reading is made
within the timeout period.
2. Userspace disables interrupts => powers sensor off
3. Userspace reads sensor data = 0 because sensor is off and the
suspend timeout has not passed. For each new reading made within the
timeout period the timeout is renewed with 2000ms and RPM will not
make a new resume (device was not suspended). So the sensor will
not be powered on.
4. No further userspace reading for 2000ms ends RPM suspend timeout and
triggers suspend (powers off already powered off sensor).
Powering sensor off in (2) makes all consecutive readings made within
2000ms to the previous reading (3) return invalid data.
Skip setting power state when writing new event config.
Fixes: 546676121c ("iio: light: vcnl4000: Add interrupt support for vcnl4040")
Fixes: bc292aaf9c ("iio: light: vcnl4000: add illuminance irq vcnl4040/4200")
Signed-off-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20230907-vcnl4000-pm-fix-v2-1-298e01f54db4@axis.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Building ad74413r without selecting IIO_BUFFER and
IIO_TRIGGERED_BUFFER generates error with respect to the iio trigger
functions that are used within the driver.
Update the Kconfig accordingly.
Fixes: fea251b6a5 ("iio: addac: add AD74413R driver")
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20230912085421.51102-1-antoniu.miclaus@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The DPS310 sensor chip has been encountering intermittent errors while
reading the sensor device across various system designs. This issue causes
the chip to become "stuck," preventing the indication of "ready" status
for pressure and temperature measurements in the MEAS_CFG register.
To address this issue, this commit fixes the timeout settings to improve
sensor stability:
- After sending a reset command to the chip, the timeout has been extended
from 2.5 ms to 15 ms, aligning with the DPS310 specification.
- The read timeout value of the MEAS_CFG register has been adjusted from
20ms to 30ms to match the specification.
Signed-off-by: Lakshmi Yadlapati <lakshmiy@us.ibm.com>
Fixes: 7b4ab4abce ("iio: pressure: dps310: Reset chip after timeout")
Link: https://lore.kernel.org/r/20230829180222.3431926-2-lakshmiy@us.ibm.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver uses IIO triggered buffers so it needs to select them in
Kconfig.
on riscv-32bit:
/opt/crosstool/gcc-13.2.0-nolibc/riscv32-linux/bin/riscv32-linux-ld: drivers/iio/imu/bno055/bno055.o: in function `.L367':
bno055.c:(.text+0x2c96): undefined reference to `devm_iio_triggered_buffer_setup_ext'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Closes: https://lore.kernel.org/linux-next/40566b4b-3950-81fe-ff14-871d8c447627@infradead.org/
Fixes: 4aefe1c2bd ("iio: imu: add Bosch Sensortec BNO055 core driver")
Cc: Andrea Merello <andrea.merello@iit.it>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20230903113052.846298-1-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC Command Buffer Register high and low are currently pointing to
the wrong address and makes it impossible to perform correct
ADC measurements over all channels.
According to the datasheet of the imx8qxp the ADC_CMDL register starts
at address 0x100 and the ADC_CMDH register starts at address 0x104.
This bug seems to be in the kernel since the introduction of this
driver.
This can be observed by checking all raw voltages of the adc and they
are all nearly identical:
cat /sys/bus/iio/devices/iio\:device0/in_voltage*_raw
3498
3494
3491
3491
3489
3490
3490
3490
Fixes: 1e23dcaa1a ("iio: imx8qxp-adc: Add driver support for NXP IMX8QXP ADC")
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
Acked-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20230904220204.23841-1-embed3d@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
cros_ec_sensors_push_data() reads `indio_dev->active_scan_mask` and
calls iio_push_to_buffers_with_timestamp() without making sure the
`indio_dev` stays in buffer mode. There is a race if `indio_dev` exits
buffer mode right before cros_ec_sensors_push_data() accesses them.
An use-after-free on `indio_dev->active_scan_mask` was observed. The
call trace:
[...]
_find_next_bit
cros_ec_sensors_push_data
cros_ec_sensorhub_event
blocking_notifier_call_chain
cros_ec_irq_thread
It was caused by a race condition: one thread just freed
`active_scan_mask` at [1]; while another thread tried to access the
memory at [2].
Fix it by calling iio_device_claim_buffer_mode() to ensure the
`indio_dev` can't exit buffer mode during cros_ec_sensors_push_data().
[1]: https://elixir.bootlin.com/linux/v6.5/source/drivers/iio/industrialio-buffer.c#L1189
[2]: https://elixir.bootlin.com/linux/v6.5/source/drivers/iio/common/cros_ec_sensors/cros_ec_sensors_core.c#L198
Cc: stable@vger.kernel.org
Fixes: aa984f1ba4 ("iio: cros_ec: Register to cros_ec_sensorhub when EC supports FIFO")
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20230829030622.1571852-1-tzungbi@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When compiling with gcc 13 with -Warray-bounds enabled:
In file included from drivers/iio/proximity/irsd200.c:15:
In function ‘iio_push_to_buffers_with_timestamp’,
inlined from ‘irsd200_trigger_handler’ at drivers/iio/proximity/irsd200.c:770:2:
./include/linux/iio/buffer.h:42:46: error: array subscript ‘int64_t {aka long long int}[0]’
is partly outside array bounds of ‘s16[1]’ {aka ‘short int[1]’} [-Werror=array-bounds=]
42 | ((int64_t *)data)[ts_offset] = timestamp;
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~
drivers/iio/proximity/irsd200.c: In function ‘irsd200_trigger_handler’:
drivers/iio/proximity/irsd200.c:763:13: note: object ‘buf’ of size 2
763 | s16 buf = 0;
| ^~~
The problem seems to be that irsd200_trigger_handler() is taking a s16
variable as an int64_t buffer. As Jonathan suggested [1], fix it by
extending the buffer to a two-element array of s64.
Link: https://github.com/KSPP/linux/issues/331
Link: https://lore.kernel.org/lkml/20230809181329.46c00a5d@jic23-huawei/ [1]
Fixes: 3db3562bc6 ("iio: Add driver for Murata IRS-D200")
Signed-off-by: GONG, Ruiqi <gongruiqi1@huawei.com>
Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Waqar Hameed <waqar.hameed@axis.com>
Tested-by: Waqar Hameed <waqar.hameed@axis.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230810035910.1334706-1-gongruiqi@huaweicloud.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Explicity specify array indices to fix mapping between
asahi_compass_chipset and ak_def_array.
While at it, remove unneeded AKXXXX.
Fixes: 4f9ea93afd ("iio: magnetometer: ak8975: Convert enum->pointer for data in the match tables")
Signed-off-by: André Apitzsch <git@apitzsch.eu>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231001-ak_magnetometer-v1-1-09bf3b8798a3@apitzsch.eu
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
strncpy() is deprecated for use on NUL-terminated destination strings [1].
We should prefer more robust and less ambiguous string interfaces.
We expect adc->chan_name[val] to be NUL-terminated based on ch_name's
use within functions that expect NUL-terminated strings like strncmp and
printf-likes:
| if (!strncmp(stm32_adc_ic[i].name, ch_name, STM32_ADC_CH_SZ)) {
| /* Check internal channel availability */
| switch (i) {
| case STM32_ADC_INT_CH_VDDCORE:
| if (!adc->cfg->regs->or_vddcore.reg)
| dev_warn(&indio_dev->dev,
| "%s channel not available\n", ch_name);
...
There is no evidence that NUL-padding is needed either.
Considering the above, a suitable replacement is strscpy() [2] due to
the fact that it guarantees NUL-termination on the destination buffer
without unnecessarily NUL-padding. If, for any reason, NUL-padding _is_
required we should go for `strscpy_pad`.
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html [2]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230921-strncpy-drivers-iio-adc-stm32-adc-c-v1-1-c50eca098597@google.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
dt-bindings: iio: Add KX132ACR-LBZ accelerometer
ROHM KX132ACR-LBZ is an accelerometer for industrial applications. It
has a subset of KX022A functionalities, dropping support for tap, free
fall and tilt detection engines. Also, the register interface is an exact
subset of what is found on KX022A (except the WHO_AM_I register value).
Add support for KX132ACR-LBZ.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/272065b9f35b817aff86b7760ff1aaaaaaa969f5.1695879676.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of using the f_order member of ad7192_state, a function that
computes the f_order coefficient makes more sense. This coefficient is a
function of the sinc filter and chop filter states.
Remove f_order member of ad7192_state structure. Instead use
ad7192_compute_f_order function to compute the f_order coefficient
according to the sinc filter and chop filter states passed as
parameters.
Add ad7192_get_f_order function that returns the current f_order
coefficient of the device.
Add ad7192_compute_f_adc function that computes the f_adc value
according to the sinc filter and chop filter states passed as
parameters.
Add ad7192_get_f_adc function that returns the current f_adc value of
the device.
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Link: https://lore.kernel.org/r/20230924215148.102491-3-alisadariana@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Include bitfield.h and update driver to use bitfield access macros GENMASK,
FIELD_PREP and FIELD_GET.
Remove old macros in favor of using FIELD_PREP and masks.
Change %d to %ld to match the type of FIELD_GET().
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Link: https://lore.kernel.org/r/20230924215148.102491-2-alisadariana@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Support for the ROHM BM1390 pressure sensor. The BM1390GLV-Z can measure
pressures ranging from 300 hPa to 1300 hPa with configurable measurement
averaging and internal FIFO. The sensor does also provide temperature
measurements.
Sensor does also contain IIR filter implemented in HW. The data-sheet
says the IIR filter can be configured to be "weak", "middle" or
"strong". Some RMS noise figures are provided in data sheet but no
accurate maths for the filter configurations is provided. Hence, the IIR
filter configuration is not supported by this driver and the filter is
configured to the "middle" setting (at least not for now).
The FIFO measurement mode is only measuring the pressure and not the
temperature. The driver measures temperature when FIFO is flushed and
simply uses the same measured temperature value to all reported
temperatures. This should not be a problem when temperature is not
changing very rapidly (several degrees C / second) but allows users to
get the temperature measurements from sensor without any additional logic.
This driver allows the sensor to be used in two muitually exclusive ways,
1. With trigger (data-ready IRQ).
In this case the FIFO is not used as we get data ready for each collected
sample. Instead, for each data-ready IRQ we read the sample from sensor
and push it to the IIO buffer.
2. With hardware FIFO and watermark IRQ.
In this case the data-ready is not used but we enable watermark IRQ. At
each watermark IRQ we go and read all samples in FIFO and push them to the
IIO buffer.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Link: https://lore.kernel.org/r/4f23211e3cf248f9f48ddb2a752387bb00e9c2c4.1695727471.git.mazziesaccount@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some boards fail in magnetometer probe if level shifter flag is not set,
definition was found in the vendor Linux kernel v3.0.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20230927173245.2151083-3-andreas@kemnade.info
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The temperature channel has 16-bit storage size. We need to perform
the padding to have the buffer elements naturally aligned in case
the temperature channel is enabled and there are any 32-bit storage
size channels enabled which have a scan index higher than the
temperature channel scan index.
Fixes: 8f6bc87d67 ("iio: imu: adis16475.c: Add delta angle and delta velocity channels")
Signed-off-by: Ramona Gradinariu <ramona.gradinariu@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20230926085721.645687-2-ramona.gradinariu@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The deta angle and deta velocity channels were added in parallel with
color temperature and chromacity so this merge had to assign a
consistent order. I put the color related ones second.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support the x and y light
colors, which represent the coordinates on the CIE 1931 chromaticity
diagram. Thus, add light chromaticity x and y.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-8-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support the x and y light
colors, which represent the coordinates on the CIE 1931 chromaticity
diagram. Thus, add channel type for chromaticity.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-7-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support light color temperature.
As a result, add support of light color temperature.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-4-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In most cases, ambient color sensors also support light color
temperature, which is measured in kelvin. Thus, add channel type light
color temperature.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-3-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Sensor hub attributes can be extended to support more channels. Repeat
the reading for the two existing channels and store them separately. It
still operates in the same manner as before where there was just one
entry. So in order to support more sensor hub attributes for ALS use
channel index to get specific sensor hub attributes.
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Acked-by: Srinivas Pandruvada<srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20230919081054.2050714-2-Basavaraj.Natikar@amd.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-50-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-49-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-48-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230919174931.1417681-47-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new() which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20230919174931.1417681-46-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
