Ditch the separate oobrbuf and oobwbuf fields from the chip buffers,
and use only a single buffer immediately after the data. This accommodates
NAND controllers such as the OLPC CAFÉ chip, which can't do scatter/gather
DMA so needs the OOB buffer to be contiguous with the data, for both read
and write.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
As flash cannot do 0->1 bit transitions when programming, do not do this in
the simulator too. This makes nandsim able to accept subpage writes.
Signed-off-by: Artem Bityutskiy <dedekind@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Removes line break after return type in function definitions, to be
consistent with the Linux coding style.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
For page wise allocation, an array of flash page pointers is allocated
during initialization. The flash pages are themselves allocated when a
write occurs to the page. The flash pages are deallocated when they
are erased.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch removes code that does chip mapping. The chip mapping code
is no longer used.
Signed-off-by: Vijay Kumar <vijaykumar@bravegnu.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This version only differs from version posted by Savin Zlobec (20 Jun
2006) in that the AT91RM9200-specific chip-select / bus setup code has
been moved from the at91_nand.c driver into the processor-specific file.
From: Savin Zlobec <savin@epico.si>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Updated version of patch, in response to comments from Francois Romieu
<romieu@fr.zoreil.com>
Remove gratuitous casts from iounmap and initialisation of variables.
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
- allow high-level nand_write_page() function to be overridden
- likewise low-level write_page_raw() and read_page_raw() functions
- Clean up the abuse of chip->ecc.{write,read}_page() with MTD_OOB_RAW
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Due to this typo, a wrong ECC layout table is chosen.
Signed-off-by: Frank Haverkamp <haver@vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
ioremap must be balanced by an iounmap and failing to do so can result
in a memory leak.
Tested (compilation only) with:
- allmodconfig
- Modifying drivers/mtd/maps/Kconfig and drivers/mtd/nand/Kconfig to
make sure that the changed file is compiling without warning
Signed-off-by: Amol Lad <amol@verismonetworks.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The recent hwctrl core conversion for MTD NAND devices broke the Amstrad
Delta driver. This fixes it up and uses the existing control line defines
rather than unclear magic numbers.
Signed-off-by: Jonathan McDowell <noodles@earth.li>
Acked-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Read the return value before we release the nand device otherwise the
value can become corrupted by another user of chip->ops, ultimately
resulting in filesystem corruption.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The CNE bits are inverted on the device and writeb function is missing a
NOT operation.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In the case of data-pad-ecc-pad-data... layout the oob start position
has to be sizeof(data) in nand_write_oob_syndrom().
In nand_fill_oob() we need to copy to buf + buffer offset instead of
buf + write offset.
From: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix all kernel-doc warnings in MTD headers and source files:
- add some missing struct fields;
- correct some function parameter names;
- use kernel-doc format for function doc. headers;
- nand_ecc.c contains only exported interfaces, no internal ones;
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The other way round works not really well with boards which have a
static NAND chipselect.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
I was unable to compile ts7250.c after your refactor commit,
it's a typo probably.
-- ynezz
From: Petr Stetiar <ynezz@true.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add support for both the S3C2412 and S3C2412 Samsung SoCs to
the increasingly mis-named s3c2410.c driver.
This currently only supports SLC ECCs, and a chip on nFCE0.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The rework of the command handling in the nand driver
led to wrong address setting in the command control
function. Use the correct address again.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Convert the use of printk() to the correct dev_info/dev_err
functions
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The oob fixups broke a return value and missed one patch from
the Mailing List.
Signed-off-by: Savin Zlobec <savin@epico.si>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Following problems are addressed:
- wrong status caused early break out of nand_wait()
- removed the bogus status check in nand_wait() which
is a relict of the abandoned support for interrupted
erase.
- status check moved to the correct place in read_oob
- oob support for syndrom based ecc with strange layouts
- use given offset in the AUTOOOB based oob operations
Partially based on a patch from Vitaly Vool <vwool@ru.mvista.com>
Thanks to Savin Zlobec <savin@epico.si> for tracking down the
status problem.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In nand_read_page_syndrome/nand_write_page_syndrome the calculation of
the remaining oob length which is not used by the prepad/ecc/postpad
areas is wrong.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix unused variables and commenting since tglx's
new NAND updates
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/mtd/nand/nand_base.c: In function 'nand_transfer_oob':
drivers/mtd/nand/nand_base.c:909: warning: comparison of distinct pointer types lacks a cast
drivers/mtd/nand/nand_base.c: In function 'nand_do_read_oob':
drivers/mtd/nand/nand_base.c:1097: error: 'len' undeclared (first use in this function)
drivers/mtd/nand/nand_base.c:1097: error: (Each undeclared identifier is reported only once
drivers/mtd/nand/nand_base.c:1097: error: for each function it appears in.)
drivers/mtd/nand/nand_base.c: In function 'nand_fill_oob':
drivers/mtd/nand/nand_base.c:1411: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The raw read/write access to NAND (without ECC) has been changed in the
NAND rework. Expose the new way - setting the file mode via ioctl - to
userspace. Also allow to read out the ecc statistics information so userspace
tools can see that bitflips happened and whether errors where correctable
or not. Also expose the number of bad blocks for the partition, so nandwrite
can check if the data fits into the parition before writing to it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Return -EUCLEAN on read when a bitflip was detected and corrected, so the
clients can react and eventually copy the affected block to a spare one.
Make all in kernel users aware of the change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hopefully the last iteration on this!
The handling of out of band data on NAND was accompanied by tons of fruitless
discussions and halfarsed patches to make it work for a particular
problem. Sufficiently annoyed by I all those "I know it better" mails and the
resonable amount of discarded "it solves my problem" patches, I finally decided
to go for the big rework. After removing the _ecc variants of mtd read/write
functions the solution to satisfy the various requirements was to refactor the
read/write _oob functions in mtd.
The major change is that read/write_oob now takes a pointer to an operation
descriptor structure "struct mtd_oob_ops".instead of having a function with at
least seven arguments.
read/write_oob which should probably renamed to a more descriptive name, can do
the following tasks:
- read/write out of band data
- read/write data content and out of band data
- read/write raw data content and out of band data (ecc disabled)
struct mtd_oob_ops has a mode field, which determines the oob handling mode.
Aside of the MTD_OOB_RAW mode, which is intended to be especially for
diagnostic purposes and some internal functions e.g. bad block table creation,
the other two modes are for mtd clients:
MTD_OOB_PLACE puts/gets the given oob data exactly to/from the place which is
described by the ooboffs and ooblen fields of the mtd_oob_ops strcuture. It's
up to the caller to make sure that the byte positions are not used by the ECC
placement algorithms.
MTD_OOB_AUTO puts/gets the given oob data automaticaly to/from the places in
the out of band area which are described by the oobfree tuples in the ecclayout
data structre which is associated to the devicee.
The decision whether data plus oob or oob only handling is done depends on the
setting of the datbuf member of the data structure. When datbuf == NULL then
the internal read/write_oob functions are selected, otherwise the read/write
data routines are invoked.
Tested on a few platforms with all variants. Please be aware of possible
regressions for your particular device / application scenario
Disclaimer: Any whining will be ignored from those who just contributed "hot
air blurb" and never sat down to tackle the underlying problem of the mess in
the NAND driver grown over time and the big chunk of work to fix up the
existing users. The problem was not the holiness of the existing MTD
interfaces. The problems was the lack of time to go for the big overhaul. It's
easy to add more mess to the existing one, but it takes alot of effort to go
for a real solution.
Improvements and bugfixes are welcome!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The nand_oobinfo structure is not fitting the newer error correction
demands anymore. Replace it by struct nand_ecclayout and fixup the users
all over the place. Keep the nand_oobinfo based ioctl for user space
compability reasons.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
