In reboot tests on several devices we were seeing a "use after free"
when slub_debug or KASAN was enabled. The kernel complained about:
Unable to handle kernel paging request at virtual address 6b6b6c2b
...which is a classic sign of use after free under slub_debug. The
stack crawl in kgdb looked like:
0 test_bit (addr=<optimized out>, nr=<optimized out>)
1 bfq_bfqq_busy (bfqq=<optimized out>)
2 bfq_select_queue (bfqd=<optimized out>)
3 __bfq_dispatch_request (hctx=<optimized out>)
4 bfq_dispatch_request (hctx=<optimized out>)
5 0xc056ef00 in blk_mq_do_dispatch_sched (hctx=0xed249440)
6 0xc056f728 in blk_mq_sched_dispatch_requests (hctx=0xed249440)
7 0xc0568d24 in __blk_mq_run_hw_queue (hctx=0xed249440)
8 0xc0568d94 in blk_mq_run_work_fn (work=<optimized out>)
9 0xc024c5c4 in process_one_work (worker=0xec6d4640, work=0xed249480)
10 0xc024cff4 in worker_thread (__worker=0xec6d4640)
Digging in kgdb, it could be found that, though bfqq looked fine,
bfqq->bic had been freed.
Through further digging, I postulated that perhaps it is illegal to
access a "bic" (AKA an "icq") after bfq_exit_icq() had been called
because the "bic" can be freed at some point in time after this call
is made. I confirmed that there certainly were cases where the exact
crashing code path would access the "bic" after bfq_exit_icq() had
been called. Sspecifically I set the "bfqq->bic" to (void *)0x7 and
saw that the bic was 0x7 at the time of the crash.
To understand a bit more about why this crash was fairly uncommon (I
saw it only once in a few hundred reboots), you can see that much of
the time bfq_exit_icq_fbqq() fully frees the bfqq and thus it can't
access the ->bic anymore. The only case it doesn't is if
bfq_put_queue() sees a reference still held.
However, even in the case when bfqq isn't freed, the crash is still
rare. Why? I tracked what happened to the "bic" after the exit
routine. It doesn't get freed right away. Rather,
put_io_context_active() eventually called put_io_context() which
queued up freeing on a workqueue. The freeing then actually happened
later than that through call_rcu(). Despite all these delays, some
extra debugging showed that all the hoops could be jumped through in
time and the memory could be freed causing the original crash. Phew!
To make a long story short, assuming it truly is illegal to access an
icq after the "exit_icq" callback is finished, this patch is needed.
Cc: stable@vger.kernel.org
Reviewed-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_flush_dcache_pages() is unused. Remove it.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some debug code suggested by Paolo was tripping when I did reboot
stress tests. Specifically in bfq_bfqq_resume_state()
"bic->saved_wr_start_at_switch_to_srt" was later than the current
value of "jiffies". A bit of debugging showed that
"bic->saved_wr_start_at_switch_to_srt" was actually 0 and a bit more
debugging showed that was because we had run through the "unlikely"
case in the bfq_bfqq_save_state() function.
Let's init "saved_wr_start_at_switch_to_srt" in the unlikely case to
something sane.
NOTE: this fixes no known real-world errors.
Reviewed-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
By mistake, there is a '&' instead of a '==' in the definition of the
macro BFQQ_TOTALLY_SEEKY. This commit replaces the wrong operator with
the correct one.
Fixes: 7074f076ff ("block, bfq: do not tag totally seeky queues as soft rt")
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Consider, on one side, a bfq_queue Q that remains empty while in
service, and, on the other side, the pending I/O of bfq_queues that,
according to their timestamps, have to be served after Q. If an
uncontrolled amount of I/O from the latter bfq_queues were dispatched
while Q is waiting for its new I/O to arrive, then Q's bandwidth
guarantees would be violated. To prevent this, I/O dispatch is plugged
until Q receives new I/O (except for a properly controlled amount of
injected I/O). Unfortunately, preemption breaks I/O-dispatch plugging,
for the following reason.
Preemption is performed in two steps. First, Q is expired and
re-scheduled. Second, the new bfq_queue to serve is chosen. The first
step is needed by the second, as the second can be performed only
after Q's timestamps have been properly updated (done in the
expiration step), and Q has been re-queued for service. This
dependency is a consequence of the way how BFQ's scheduling algorithm
is currently implemented.
But Q is not re-scheduled at all in the first step, because Q is
empty. As a consequence, an uncontrolled amount of I/O may be
dispatched until Q becomes non empty again. This breaks Q's service
guarantees.
This commit addresses this issue by re-scheduling Q even if it is
empty. This in turn breaks the assumption that all scheduled queues
are non empty. Then a few extra checks are now needed.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
BFQ enqueues the I/O coming from each process into a separate
bfq_queue, and serves bfq_queues one at a time. Each bfq_queue may be
served for at most timeout_sync milliseconds (default: 125 ms). This
service scheme is prone to the following inaccuracy.
While a bfq_queue Q1 is in service, some empty bfq_queue Q2 may
receive I/O, and, according to BFQ's scheduling policy, may become the
right bfq_queue to serve, in place of the currently in-service
bfq_queue. In this respect, postponing the service of Q2 to after the
service of Q1 finishes may delay the completion of Q2's I/O, compared
with an ideal service in which all non-empty bfq_queues are served in
parallel, and every non-empty bfq_queue is served at a rate
proportional to the bfq_queue's weight. This additional delay is equal
at most to the time Q1 may unjustly remain in service before switching
to Q2.
If Q1 and Q2 have the same weight, then this time is most likely
negligible compared with the completion time to be guaranteed to Q2's
I/O. In addition, first, one of the reasons why BFQ may want to serve
Q1 for a while is that this boosts throughput and, second, serving Q1
longer reduces BFQ's overhead. As a conclusion, it is usually better
not to preempt Q1 if both Q1 and Q2 have the same weight.
In contrast, as Q2's weight or priority becomes higher and higher
compared with that of Q1, the above delay becomes larger and larger,
compared with the I/O completion times that have to be guaranteed to
Q2 according to Q2's weight. So reducing this delay may be more
important than avoiding the costs of preempting Q1.
Accordingly, this commit preempts Q1 if Q2 has a higher weight or a
higher priority than Q1. Preemption causes Q1 to be re-scheduled, and
triggers a new choice of the next bfq_queue to serve. If Q2 really is
the next bfq_queue to serve, then Q2 will be set in service
immediately.
This change reduces the component of the I/O latency caused by the
above delay by about 80%. For example, on an (old) PLEXTOR PX-256M5
SSD, the maximum latency reported by fio drops from 15.1 to 3.2 ms for
a process doing sporadic random reads while another process is doing
continuous sequential reads.
Signed-off-by: Nicola Bottura <bottura.nicola95@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A bfq_queue Q may happen to be synchronized with another
bfq_queue Q2, i.e., the I/O of Q2 may need to be completed for Q to
receive new I/O. We call Q2 "waker queue".
If I/O plugging is being performed for Q, and Q is not receiving any
more I/O because of the above synchronization, then, thanks to BFQ's
injection mechanism, the waker queue is likely to get served before
the I/O-plugging timeout fires.
Unfortunately, this fact may not be sufficient to guarantee a high
throughput during the I/O plugging, because the inject limit for Q may
be too low to guarantee a lot of injected I/O. In addition, the
duration of the plugging, i.e., the time before Q finally receives new
I/O, may not be minimized, because the waker queue may happen to be
served only after other queues.
To address these issues, this commit introduces the explicit detection
of the waker queue, and the unconditional injection of a pending I/O
request of the waker queue on each invocation of
bfq_dispatch_request().
One may be concerned that this systematic injection of I/O from the
waker queue delays the service of Q's I/O. Fortunately, it doesn't. On
the contrary, next Q's I/O is brought forward dramatically, for it is
not blocked for milliseconds.
Reported-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Tested-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Until the base value for request service times gets finally computed
for a bfq_queue, the inject limit for that queue does depend on the
think-time state (short|long) of the queue. A timely update of the
think time then guarantees a quicker activation or deactivation of the
injection. Fortunately, the think time of a bfq_queue is updated in
the same code path as the inject limit; but after the inject limit.
This commits moves the update of the think time before the update of
the inject limit. For coherence, it moves the update of the seek time
too.
Reported-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Tested-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
I/O injection gets reduced if it increases the request service times
of the victim queue beyond a certain threshold. The threshold, in its
turn, is computed as a function of the base service time enjoyed by
the queue when it undergoes no injection.
As a consequence, for injection to work properly, the above base value
has to be accurate. In this respect, such a value may vary over
time. For example, it varies if the size or the spatial locality of
the I/O requests in the queue change. It is then important to update
this value whenever possible. This commit performs this update.
Reported-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Tested-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
One of the cases where the parameters for injection may be updated is
when there are no more in-flight I/O requests. The number of in-flight
requests is stored in the field bfqd->rq_in_driver of the descriptor
bfqd of the device. So, the controlled condition is
bfqd->rq_in_driver == 0.
Unfortunately, this is wrong because, the instruction that checks this
condition is in the code path that handles the completion of a
request, and, in particular, the instruction is executed before
bfqd->rq_in_driver is decremented in such a code path.
This commit fixes this issue by just replacing 0 with 1 in the
comparison.
Reported-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Tested-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Until the base value of the request service times gets finally
computed for a bfq_queue, the inject limit does depend on the
think-time state (short|long). The limit must be 0 or 1 if the think
time is deemed, respectively, as short or long. However, such a check
and possible limit update is performed only periodically, once per
second. So, to make the injection mechanism much more reactive, this
commit performs the update also every time the think-time state
changes.
In addition, in the following special case, this commit lets the
inject limit of a bfq_queue bfqq remain equal to 1 even if bfqq's
think time is short: bfqq's I/O is synchronized with that of some
other queue, i.e., bfqq may receive new I/O only after the I/O of the
other queue is completed. Keeping the inject limit to 1 allows the
blocking I/O to be served while bfqq is in service. And this is very
convenient both for bfqq and for the total throughput, as explained
in detail in the comments in bfq_update_has_short_ttime().
Reported-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Tested-by: Srivatsa S. Bhat (VMware) <srivatsa@csail.mit.edu>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Improve the print_req_error with additional request fields which are
helpful for debugging. Use newly introduced blk_op_str() to print the
REQ_OP_XXX in the string format.
Reviewed-by: Chao Yu <yuchao0@huawei.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that we've a helper function blk_op_str() to convert the
REQ_OP_XXX to string XXX, adjust the code to use that. Get rid of
the duplicate array op_name which is now present in the blk-core.c
which we renamed it to "blk_op_name" and open coding in the
blk-mq-debugfs.c.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In order to centralize the REQ_OP_XXX to string conversion which can be
used in the block layer and different places in the kernel like f2fs,
this patch adds a new helper function along with an array similar to the
one present in the blk-mq-debugfs.c.
We keep this helper functionality centralize under blk-core.c instead of
blk-mq-debugfs.c since blk-core.c is configured using CONFIG_BLOCK and
it will not be dependent on blk-mq-debugfs.c which is configured using
CONFIG_BLK_DEBUG_FS.
Next patch adjusts the code in the blk-mq-debugfs.c with newly
introduced helper.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Print the calling function instead of print_req_error as a prefix, and
print the operation and op_flags separately instead of the whole field.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This option is entirely bfq specific, give it an appropinquate name.
Also make it depend on CONFIG_BFQ_GROUP_IOSCHED in Kconfig, as all
the functionality already does so anyway.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This function was moved from core block code and is way to generic.
Fold it into the only caller and simplify it based on the actually
passed arguments.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This structure and assorted infrastructure is only used by the bfq I/O
scheduler. Move it there instead of bloating the common code.
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When sampling the blkcg counts we don't need atomics or per-cpu
variables. Introduce a new structure just containing plain u64
counters.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Returning a structure generates rather bad code, so switch to passing
by reference. Also don't require the structure to be zeroed and add
to the 0-initialized counters, but actually set the counters to the
calculated value.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Trying to break up the crazy statements to something readable.
Also switch to an unsigned counter as it can't ever turn negative.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This function just has a few trivial assignments, has two callers with
one of them being in the fastpath.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that we don't need to assign the front/back segment sizes, we can
duplicating the segs assignment for the split vs no-split case and
remove a whole chunk of boilerplate code.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Return the segement and let the callers assign them, which makes the code
a littler more obvious. Also pass the request instead of q plus bio
chain, allowing for the use of rq_for_each_bvec.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We only need the number of segments in the blk-mq submission path.
Remove the field from struct bio, and return it from a variant of
blk_queue_split instead of that it can passed as an argument to
those functions that need the value.
This also means we stop recounting segments except for cloning
and partial segments.
To keep the number of arguments in this how path down remove
pointless struct request_queue arguments from any of the functions
that had it and grew a nr_segs argument.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
lightnvm should have never used this function, as it is sending
passthrough requests, so switch it to blk_rq_append_bio like all the
other passthrough request users. Inline blk_init_request_from_bio into
the only remaining caller.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Javier González <javier@javigon.com>
Reviewed-by: Matias Bjørling <mb@lightnvm.io>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The priority field also makes sense for passthrough requests, so
initialize it in blk_rq_bio_prep.
Reviewed-by: Minwoo Im <minwoo.im.dev@gmail.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As is, iolatency recognizes done_bio and cleanup as ending paths. If a
request is marked REQ_NOWAIT and fails to get a request, the bio is
cleaned up via rq_qos_cleanup() and ended in bio_wouldblock_error().
This results in underflowing the inflight counter. Fix this by only
accounting bios that were actually submitted.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit a1ce35fa49 ("block: remove dead elevator code")
deleted blk_end_request() and friends, but some declaration are still
left. Purge them.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is a pure code cleanup patch and doesn't change any functionality.
Having multiple coding styles in the code creates confusion when
someone tries to add a new code.
Make queue_poll_stat_show() consistent by adding spaces around binary
operators with the rest of the code.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In function __blk_mq_debugfs_rq_show variable op has unsigned int type.
Since op can never be negative use %u format specifier to match the
variable type.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is a pure code cleanup patch and doesn't change any functionality.
This removes the redundant else in the code which is not needed since
we are returning from function anyway.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is a pure code cleanup patch and doesn't change any functionality.
In block layer to identify the request operation req_op() macro is
used, so change the open coding the req_op() in the blk-mq-debugfs.c.
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When multiple iovecs reference the same page, each get_user_page call
will add a reference to the page. But once we've created the bio that
information gets lost and only a single reference will be dropped after
I/O completion. Use the same_page information returned from
__bio_try_merge_page to drop additional references to pages that were
already present in the bio.
Based on a patch from Ming Lei.
Link: https://lkml.org/lkml/2019/4/23/64
Fixes: 576ed913 ("block: use bio_add_page in bio_iov_iter_get_pages")
Reported-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We currently have an input same_page parameter to __bio_try_merge_page
to prohibit merging in the same page. The rationale for that is that
some callers need to account for every page added to a bio. Instead of
letting these callers call twice into the merge code to account for the
new vs existing page cases, just turn the paramter into an output one that
returns if a merge in the same page occured and let them act accordingly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When blkcg_activate_policy() is creating blkg_policy_data for existing
blkgs, it did in the wrong order - descendants first. Fix it. None
of the existing controllers seem affected by this.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blkg alloc is performed as a separate step from the rest of blkg
creation so that GFP_KERNEL allocations can be used when creating
blkgs from configuration file writes because otherwise user actions
may fail due to failures of opportunistic GFP_NOWAIT allocations.
While making blkgs use percpu_ref, 7fcf2b033b ("blkcg: change blkg
reference counting to use percpu_ref") incorrectly added unconditional
opportunistic percpu_ref_init() to blkg_create() breaking this
guarantee.
This patch moves percpu_ref_init() to blkg_alloc() so makes it use
@gfp_mask that blkg_alloc() is called with. Also, percpu_ref_exit()
is moved to blkg_free() for consistency.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 7fcf2b033b ("blkcg: change blkg reference counting to use percpu_ref")
Cc: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Depending on the number of devices, blkcg stats can go over the
default seqfile buf size. seqfile normally retries with a larger
buffer but since the ->pd_stat() addition, blkcg_print_stat() doesn't
tell seqfile that overflow has happened and the output gets printed
truncated. Fix it by calling seq_commit() w/ -1 on possible
overflows.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: 903d23f0a3 ("blk-cgroup: allow controllers to output their own stats")
Cc: stable@vger.kernel.org # v4.19+
Cc: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If use_delay was non-zero when the latency target of a cgroup was set
to zero, it will stay stuck until io.latency is enabled on the cgroup
again. This keeps readahead disabled for the cgroup impacting
performance negatively.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <jbacik@fb.com>
Fixes: d706751215 ("block: introduce blk-iolatency io controller")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Jens Axboe <axboe@kernel.dk>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct bio_map_data {
...
struct iovec iov[];
};
instance = kmalloc(sizeof(sizeof(struct bio_map_data) + sizeof(struct iovec) *
count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kmalloc(struct_size(instance, iov, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace the following form:
sizeof(*new_ptbl) + target * sizeof(new_ptbl->part[0])
with:
struct_size(new_ptbl, part, target)
Also, notice that variable size is unnecessary, hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
struct blk_rq_stat::mean is a u64 value, so use %llu
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Convert the cgroup-v1 files to ReST format, in order to
allow a later addition to the admin-guide.
The conversion is actually:
- add blank lines and identation in order to identify paragraphs;
- fix tables markups;
- add some lists markups;
- mark literal blocks;
- adjust title markups.
At its new index.rst, let's add a :orphan: while this is not linked to
the main index.rst file, in order to avoid build warnings.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
blk_mq_sched_free_requests() may be called in failure path in which
q->elevator may not be setup yet, so remove WARN_ON(!q->elevator) from
blk_mq_sched_free_requests for avoiding the false positive.
This function is actually safe to call in case of !q->elevator because
hctx->sched_tags is checked.
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Yi Zhang <yi.zhang@redhat.com>
Fixes: c3e2219216 ("block: free sched's request pool in blk_cleanup_queue")
Reported-by: syzbot+b9d0d56867048c7bcfde@syzkaller.appspotmail.com
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
When all of these checks are cleaned up, lots of the functions used in
the blk-mq-debugfs code can now return void, as no need to check the
return value of them either.
Overall, this ends up cleaning up the code and making it smaller, always
a nice win.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In most use cases of zoned block devices (aka SMR disks), the
mq-deadline scheduler is mandatory as it implements sequential write
command processing guarantees with zone write locking. So make sure that
this scheduler is always enabled if CONFIG_BLK_DEV_ZONED is selected.
Tested-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There's some discussion on how to do this the best, and Tejun prefers
that BFQ just create the file itself instead of having cgroups support
a symlink feature.
Hence revert commit 54b7b868e8 and 19e9da9e86 for 5.2, and this
can be done properly for 5.3.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Many userspace tools and services use the proportional-share policy of
the blkio/io cgroups controller. The CFQ I/O scheduler implemented
this policy for the legacy block layer. To modify the weight of a
group in case CFQ was in charge, the 'weight' parameter of the group
must be modified. On the other hand, the BFQ I/O scheduler implements
the same policy in blk-mq, but, with BFQ, the parameter to modify has
a different name: bfq.weight (forced choice until legacy block was
present, because two different policies cannot share a common parameter
in cgroups).
Due to CFQ legacy, most if not all userspace configurations still use
the parameter 'weight', and for the moment do not seem likely to be
changed. But, when CFQ went away with legacy block, such a parameter
ceased to exist.
So, a simple workaround has been proposed [1] to make all
configurations work: add a symlink, named weight, to bfq.weight. This
commit adds such a symlink.
[1] https://lkml.org/lkml/2019/4/8/555
Suggested-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Angelo Ruocco <angeloruocco90@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In theory, IO scheduler belongs to request queue, and the request pool
of sched tags belongs to the request queue too.
However, the current tags allocation interfaces are re-used for both
driver tags and sched tags, and driver tags is definitely host wide,
and doesn't belong to any request queue, same with its request pool.
So we need tagset instance for freeing request of sched tags.
Meantime, blk_mq_free_tag_set() often follows blk_cleanup_queue() in case
of non-BLK_MQ_F_TAG_SHARED, this way requires that request pool of sched
tags to be freed before calling blk_mq_free_tag_set().
Commit 47cdee29ef ("block: move blk_exit_queue into __blk_release_queue")
moves blk_exit_queue into __blk_release_queue for simplying the fast
path in generic_make_request(), then causes oops during freeing requests
of sched tags in __blk_release_queue().
Fix the above issue by move freeing request pool of sched tags into
blk_cleanup_queue(), this way is safe becasue queue has been frozen and no any
in-queue requests at that time. Freeing sched tags has to be kept in queue's
release handler becasue there might be un-completed dispatch activity
which might refer to sched tags.
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Fixes: 47cdee29ef ("block: move blk_exit_queue into __blk_release_queue")
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Reported-by: kernel test robot <rong.a.chen@intel.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
IS_ERR(_OR_NULL) already contain an 'unlikely' compiler flag,
so no need to do that again from its callers. Drop it.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
While troubleshooting issues where cloned request limits have been
exceeded, it is often beneficial to know the actual values that
have been breached. Print these values, assisting in ease of
identification of root cause of the breach.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: John Pittman <jpittman@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Document the meaning of the blk_mq_hw_queue_to_node() arguments.
Reviewed-by: Chaitanya Kulkarni <chiatanya.kulkarni@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Change one occurrence of 'performace' into 'performance'.
Cc: Max Gurtovoy <maxg@mellanox.com>
Fixes: fe631457ff ("blk-mq: map all HWQ also in hyperthreaded system") # v4.13.
Reviewed-by: Chaitanya Kulkarni <chiatanya.kulkarni@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch avoids that the kernel-doc script complains about these
function headers when building with W=1.
Cc: Hannes Reinecke <hare@suse.com>
Cc: Keith Busch <keith.busch@intel.com>
Fixes: ed76e329d7 ("blk-mq: abstract out queue map") # v5.0.
Fixes: e42b3867de ("blk-mq-rdma: pass in queue map to blk_mq_rdma_map_queues") # v5.0.
Reviewed-by: Chaitanya Kulkarni <chiatanya.kulkarni@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch avoids that the kernel-doc tool warns about this function
header when building with W=1.
Reviewed-by: Chaitanya Kulkarni <chiatanya.kulkarni@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch avoids that the kernel-doc tool warns about this function
header when building with W=1.
Reviewed-by: Chaitanya Kulkarni <chiatanya.kulkarni@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If blk_mq_init_allocated_queue() fails, make sure to free the poll
stat callback struct allocated.
Signed-off-by: Jes Sorensen <jsorensen@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now a063057d7c ("block: Fix a race between request queue removal and
the block cgroup controller") has been reverted, and blkcg_exit_queue()
won't be called in blk_cleanup_queue() any more.
So don't need to protect generic_make_request_checks() with
blk_queue_enter(), then the total mess can be cleaned.
37f9579f4c ("blk-mq: Avoid that submitting a bio concurrently with device
removal triggers a crash") is reverted.
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 498f6650ae ("block: Fix a race between the cgroup code and
request queue initialization") moves what blk_exit_queue does into
blk_cleanup_queue() for fixing issue caused by changing back
queue lock.
However, after legacy request IO path is killed, driver queue lock
won't be used at all, and there isn't story for changing back
queue lock. Then the issue addressed by Commit 498f6650ae doesn't
exist any more.
So move move blk_exit_queue into __blk_release_queue.
This patch basically reverts the following two commits:
498f6650ae block: Fix a race between the cgroup code and request queue initialization
24ecc35853 block: Ensure that a request queue is dissociated from the cgroup controller
Cc: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The following is a description of a hang in blk_mq_freeze_queue_wait().
The hang happens on attempt to freeze a queue while another task does
queue unfreeze.
The root cause is an incorrect sequence of percpu_ref_resurrect() and
percpu_ref_kill() and as a result those two can be swapped:
CPU#0 CPU#1
---------------- -----------------
q1 = blk_mq_init_queue(shared_tags)
q2 = blk_mq_init_queue(shared_tags):
blk_mq_add_queue_tag_set(shared_tags):
blk_mq_update_tag_set_depth(shared_tags):
list_for_each_entry()
blk_mq_freeze_queue(q1)
> percpu_ref_kill()
> blk_mq_freeze_queue_wait()
blk_cleanup_queue(q1)
blk_mq_freeze_queue(q1)
> percpu_ref_kill()
^^^^^^ freeze_depth can't guarantee the order
blk_mq_unfreeze_queue()
> percpu_ref_resurrect()
> blk_mq_freeze_queue_wait()
^^^^^^ Hang here!!!!
This wrong sequence raises kernel warning:
percpu_ref_kill_and_confirm called more than once on blk_queue_usage_counter_release!
WARNING: CPU: 0 PID: 11854 at lib/percpu-refcount.c:336 percpu_ref_kill_and_confirm+0x99/0xb0
But the most unpleasant effect is a hang of a blk_mq_freeze_queue_wait(),
which waits for a zero of a q_usage_counter, which never happens
because percpu-ref was reinited (instead of being killed) and stays in
PERCPU state forever.
How to reproduce:
- "insmod null_blk.ko shared_tags=1 nr_devices=0 queue_mode=2"
- cpu0: python Script.py 0; taskset the corresponding process running on cpu0
- cpu1: python Script.py 1; taskset the corresponding process running on cpu1
Script.py:
------
#!/usr/bin/python3
import os
import sys
while True:
on = "echo 1 > /sys/kernel/config/nullb/%s/power" % sys.argv[1]
off = "echo 0 > /sys/kernel/config/nullb/%s/power" % sys.argv[1]
os.system(on)
os.system(off)
------
This bug was first reported and fixed by Roman, previous discussion:
[1] Message id: 1443287365-4244-7-git-send-email-akinobu.mita@gmail.com
[2] Message id: 1443563240-29306-6-git-send-email-tj@kernel.org
[3] https://patchwork.kernel.org/patch/9268199/
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Roman Pen <roman.penyaev@profitbricks.com>
Signed-off-by: Bob Liu <bob.liu@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
At this point these fields aren't used for anything, so we can remove
them.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We fundamentally do not have a maximum segement size for devices with a
virt boundary. So don't bother checking it, especially given that the
existing checks didn't properly work to start with as we never fully
update the front/back segment size and miss the bi_seg_front_size that
wuld have been required for some cases.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We currently fail to update the front/back segment size in the bio when
deciding to allow an otherwise gappy segement to a device with a
virt boundary. The reason why this did not cause problems is that
devices with a virt boundary fundamentally don't use segments as we
know it and thus don't care. Make that assumption formal by forcing
an unlimited segement size in this case.
Fixes: f6970f83ef ("block: don't check if adjacent bvecs in one bio can be mergeable")
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently ll_merge_requests_fn, unlike all other merge functions,
reduces nr_phys_segments by one if the last segment of the previous,
and the first segment of the next segement are contigous. While this
seems like a nice solution to avoid building smaller than possible
requests it causes a mismatch between the segments actually present
in the request and those iterated over by the bvec iterators, including
__rq_for_each_bio. This can for example mistrigger the single segment
optimization in the nvme-pci driver, and might lead to mismatching
nr_phys_segments number when recalculating the number of request
when inserting a cloned request.
We could possibly work around this by making the bvec iterators take
the front and back segment size into account, but that would require
moving them from the bio to the bio_iter and spreading this mess
over all users of bvecs. Or we could simply remove this optimization
under the assumption that most users already build good enough bvecs,
and that the bio merge patch never cared about this optimization
either. The latter is what this patch does.
dff824b2aa ("nvme-pci: optimize mapping of small single segment requests").
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=ZKv1
-----END PGP SIGNATURE-----
Merge tag 'for-5.2/block-post-20190516' of git://git.kernel.dk/linux-block
Pull more block updates from Jens Axboe:
"This is mainly some late lightnvm changes that came in just before the
merge window, as well as fixes that have been queued up since the
initial pull request was frozen.
This contains:
- lightnvm changes, fixing race conditions, improving memory
utilization, and improving pblk compatability (Chansol, Igor,
Marcin)
- NVMe pull request with minor fixes all over the map (via Christoph)
- remove redundant error print in sata_rcar (Geert)
- struct_size() cleanup (Jackie)
- dasd CONFIG_LBADF warning fix (Ming)
- brd cond_resched() improvement (Mikulas)"
* tag 'for-5.2/block-post-20190516' of git://git.kernel.dk/linux-block: (41 commits)
block/bio-integrity: use struct_size() in kmalloc()
nvme: validate cntlid during controller initialisation
nvme: change locking for the per-subsystem controller list
nvme: trace all async notice events
nvme: fix typos in nvme status code values
nvme-fabrics: remove unused argument
nvme-multipath: avoid crash on invalid subsystem cntlid enumeration
nvme-fc: use separate work queue to avoid warning
nvme-rdma: remove redundant reference between ib_device and tagset
nvme-pci: mark expected switch fall-through
nvme-pci: add known admin effects to augument admin effects log page
nvme-pci: init shadow doorbell after each reset
brd: add cond_resched to brd_free_pages
sata_rcar: Remove ata_host_alloc() error printing
s390/dasd: fix build warning in dasd_eckd_build_cp_raw
lightnvm: pblk: use nvm_rq_to_ppa_list()
lightnvm: pblk: simplify partial read path
lightnvm: do not remove instance under global lock
lightnvm: track inflight target creations
lightnvm: pblk: recover only written metadata
...
Use the new struct_size() helper to keep code simple.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=Ot0g
-----END PGP SIGNATURE-----
Merge tag 'for-5.2/block-20190507' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"Nothing major in this series, just fixes and improvements all over the
map. This contains:
- Series of fixes for sed-opal (David, Jonas)
- Fixes and performance tweaks for BFQ (via Paolo)
- Set of fixes for bcache (via Coly)
- Set of fixes for md (via Song)
- Enabling multi-page for passthrough requests (Ming)
- Queue release fix series (Ming)
- Device notification improvements (Martin)
- Propagate underlying device rotational status in loop (Holger)
- Removal of mtip32xx trim support, which has been disabled for years
(Christoph)
- Improvement and cleanup of nvme command handling (Christoph)
- Add block SPDX tags (Christoph)
- Cleanup/hardening of bio/bvec iteration (Christoph)
- A few NVMe pull requests (Christoph)
- Removal of CONFIG_LBDAF (Christoph)
- Various little fixes here and there"
* tag 'for-5.2/block-20190507' of git://git.kernel.dk/linux-block: (164 commits)
block: fix mismerge in bvec_advance
block: don't drain in-progress dispatch in blk_cleanup_queue()
blk-mq: move cancel of hctx->run_work into blk_mq_hw_sysfs_release
blk-mq: always free hctx after request queue is freed
blk-mq: split blk_mq_alloc_and_init_hctx into two parts
blk-mq: free hw queue's resource in hctx's release handler
blk-mq: move cancel of requeue_work into blk_mq_release
blk-mq: grab .q_usage_counter when queuing request from plug code path
block: fix function name in comment
nvmet: protect discovery change log event list iteration
nvme: mark nvme_core_init and nvme_core_exit static
nvme: move command size checks to the core
nvme-fabrics: check more command sizes
nvme-pci: check more command sizes
nvme-pci: remove an unneeded variable initialization
nvme-pci: unquiesce admin queue on shutdown
nvme-pci: shutdown on timeout during deletion
nvme-pci: fix psdt field for single segment sgls
nvme-multipath: don't print ANA group state by default
nvme-multipath: split bios with the ns_head bio_set before submitting
...
Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said they
should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here, due
to some changes to the kobject core code. Those too have all been acked
by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXNHDbw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynDAgCfbb4LBR6I50wFXb8JM/R6cAS7qrsAn1unshKV
8XCYcif2RxjtdJWXbjdm
=/rLh
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core/kobject updates from Greg KH:
"Here is the "big" set of driver core patches for 5.2-rc1
There are a number of ACPI patches in here as well, as Rafael said
they should go through this tree due to the driver core changes they
required. They have all been acked by the ACPI developers.
There are also a number of small subsystem-specific changes in here,
due to some changes to the kobject core code. Those too have all been
acked by the various subsystem maintainers.
As for content, it's pretty boring outside of the ACPI changes:
- spdx cleanups
- kobject documentation updates
- default attribute groups for kobjects
- other minor kobject/driver core fixes
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-5.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (47 commits)
kobject: clean up the kobject add documentation a bit more
kobject: Fix kernel-doc comment first line
kobject: Remove docstring reference to kset
firmware_loader: Fix a typo ("syfs" -> "sysfs")
kobject: fix dereference before null check on kobj
Revert "driver core: platform: Fix the usage of platform device name(pdev->name)"
init/config: Do not select BUILD_BIN2C for IKCONFIG
Provide in-kernel headers to make extending kernel easier
kobject: Improve doc clarity kobject_init_and_add()
kobject: Improve docs for kobject_add/del
driver core: platform: Fix the usage of platform device name(pdev->name)
livepatch: Replace klp_ktype_patch's default_attrs with groups
cpufreq: schedutil: Replace default_attrs field with groups
padata: Replace padata_attr_type default_attrs field with groups
irqdesc: Replace irq_kobj_type's default_attrs field with groups
net-sysfs: Replace ktype default_attrs field with groups
block: Replace all ktype default_attrs with groups
samples/kobject: Replace foo_ktype's default_attrs field with groups
kobject: Add support for default attribute groups to kobj_type
driver core: Postpone DMA tear-down until after devres release for probe failure
...
Now freeing hw queue resource is moved to hctx's release handler,
we don't need to worry about the race between blk_cleanup_queue and
run queue any more.
So don't drain in-progress dispatch in blk_cleanup_queue().
This is basically revert of c2856ae2f3 ("blk-mq: quiesce queue before
freeing queue").
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org,
Cc: Martin K . Petersen <martin.petersen@oracle.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>,
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
hctx is always released after requeue is freed.
With holding queue's kobject refcount, it is safe for driver to run queue,
so one run queue might be scheduled after blk_sync_queue() is done.
So moving the cancel of hctx->run_work into blk_mq_hw_sysfs_release()
for avoiding run released queue.
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org,
Cc: Martin K . Petersen <martin.petersen@oracle.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>,
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In normal queue cleanup path, hctx is released after request queue
is freed, see blk_mq_release().
However, in __blk_mq_update_nr_hw_queues(), hctx may be freed because
of hw queues shrinking. This way is easy to cause use-after-free,
because: one implicit rule is that it is safe to call almost all block
layer APIs if the request queue is alive; and one hctx may be retrieved
by one API, then the hctx can be freed by blk_mq_update_nr_hw_queues();
finally use-after-free is triggered.
Fixes this issue by always freeing hctx after releasing request queue.
If some hctxs are removed in blk_mq_update_nr_hw_queues(), introduce
a per-queue list to hold them, then try to resuse these hctxs if numa
node is matched.
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org,
Cc: Martin K . Petersen <martin.petersen@oracle.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>,
Reviewed-by: Hannes Reinecke <hare@suse.com>
Tested-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Split blk_mq_alloc_and_init_hctx into two parts, and one is
blk_mq_alloc_hctx() for allocating all hctx resources, another
is blk_mq_init_hctx() for initializing hctx, which serves as
counter-part of blk_mq_exit_hctx().
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org
Cc: Martin K . Petersen <martin.petersen@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Once blk_cleanup_queue() returns, tags shouldn't be used any more,
because blk_mq_free_tag_set() may be called. Commit 45a9c9d909
("blk-mq: Fix a use-after-free") fixes this issue exactly.
However, that commit introduces another issue. Before 45a9c9d909,
we are allowed to run queue during cleaning up queue if the queue's
kobj refcount is held. After that commit, queue can't be run during
queue cleaning up, otherwise oops can be triggered easily because
some fields of hctx are freed by blk_mq_free_queue() in blk_cleanup_queue().
We have invented ways for addressing this kind of issue before, such as:
8dc765d438 ("SCSI: fix queue cleanup race before queue initialization is done")
c2856ae2f3 ("blk-mq: quiesce queue before freeing queue")
But still can't cover all cases, recently James reports another such
kind of issue:
https://marc.info/?l=linux-scsi&m=155389088124782&w=2
This issue can be quite hard to address by previous way, given
scsi_run_queue() may run requeues for other LUNs.
Fixes the above issue by freeing hctx's resources in its release handler, and this
way is safe becasue tags isn't needed for freeing such hctx resource.
This approach follows typical design pattern wrt. kobject's release handler.
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org,
Cc: Martin K . Petersen <martin.petersen@oracle.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>,
Reported-by: James Smart <james.smart@broadcom.com>
Fixes: 45a9c9d909 ("blk-mq: Fix a use-after-free")
Cc: stable@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With holding queue's kobject refcount, it is safe for driver
to schedule requeue. However, blk_mq_kick_requeue_list() may
be called after blk_sync_queue() is done because of concurrent
requeue activities, then requeue work may not be completed when
freeing queue, and kernel oops is triggered.
So moving the cancel of requeue_work into blk_mq_release() for
avoiding race between requeue and freeing queue.
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Cc: linux-scsi@vger.kernel.org,
Cc: Martin K . Petersen <martin.petersen@oracle.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>,
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Just like aio/io_uring, we need to grab 2 refcount for queuing one
request, one is for submission, another is for completion.
If the request isn't queued from plug code path, the refcount grabbed
in generic_make_request() serves for submission. In theroy, this
refcount should have been released after the sumission(async run queue)
is done. blk_freeze_queue() works with blk_sync_queue() together
for avoiding race between cleanup queue and IO submission, given async
run queue activities are canceled because hctx->run_work is scheduled with
the refcount held, so it is fine to not hold the refcount when
running the run queue work function for dispatch IO.
However, if request is staggered into plug list, and finally queued
from plug code path, the refcount in submission side is actually missed.
And we may start to run queue after queue is removed because the queue's
kobject refcount isn't guaranteed to be grabbed in flushing plug list
context, then kernel oops is triggered, see the following race:
blk_mq_flush_plug_list():
blk_mq_sched_insert_requests()
insert requests to sw queue or scheduler queue
blk_mq_run_hw_queue
Because of concurrent run queue, all requests inserted above may be
completed before calling the above blk_mq_run_hw_queue. Then queue can
be freed during the above blk_mq_run_hw_queue().
Fixes the issue by grab .q_usage_counter before calling
blk_mq_sched_insert_requests() in blk_mq_flush_plug_list(). This way is
safe because the queue is absolutely alive before inserting request.
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: James Smart <james.smart@broadcom.com>
Cc: linux-scsi@vger.kernel.org,
Cc: Martin K . Petersen <martin.petersen@oracle.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: James E . J . Bottomley <jejb@linux.vnet.ibm.com>,
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The comment was out of date.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Raul E Rangel <rrangel@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Various block layer files do not have any licensing information at all.
Add SPDX tags for the default kernel GPLv2 license to those.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All these files have some form of the usual GPLv2 or later boilerplate.
Switch them to use SPDX tags instead.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All these files have some form of the usual GPLv2 boilerplate. Switch
them to use SPDX tags instead.
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Share the bi_size update by moving the done label up, and duplicate
the bv_len update in the two callers to get rid of the bvec_merge
label.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We are never called with file system pages by defintions for the
passthrough interface, and we also never undo any addition later
these days.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The same page optimization is a rather odd corner case, which is not
used outside bio.c and which really should not be used outside of bio.c
either - we have better highlevel helpers like the rq/bio mapping
helpers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We only have two callers that need the integer loop iterator, and they
can easily maintain it themselves.
Suggested-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: David Sterba <dsterba@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Coly Li <colyli@suse.de>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The kobj_type default_attrs field is being replaced by the
default_groups field. Replace all of the ktype default_attrs fields in
the block subsystem with default_groups and use the ATTRIBUTE_GROUPS
macro to create the default groups.
Remove default_ctx_attrs[] because it doesn't contain any attributes.
This patch was tested by verifying that the sysfs files for the
attributes in the default groups were created.
Signed-off-by: Kimberly Brown <kimbrownkd@gmail.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The refcount has been increased for pages retrieved from non-bvec iov iter
via __bio_iov_iter_get_pages(), so don't need to do that again.
Otherwise, IO pages are leaked easily.
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Fixes: 7321ecbfc7 ("block: change how we get page references in bio_iov_iter_get_pages")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio_add_page() and __bio_add_page() are capable of adding pages into
bio, and now we have at least two such usages alreay:
- __bio_iov_bvec_add_pages()
- nvmet_bdev_execute_rw().
So update comments on these two helpers.
The thing is a bit special for __bio_try_merge_page(), given the caller
needs to know if the new added page is same with the last added page,
then it isn't safe to pass multi-page in case that 'same_page' is true,
so adds warning on potential misuse, and updates comment on
__bio_try_merge_page().
Cc: linux-xfs@vger.kernel.org
Cc: linux-fsdevel@vger.kernel.org
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the low level driver has no timeout handler, the
/sys/block/<disk>/queue/io_timeout will not be displayed.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Weiping Zhang <zhangweiping@didiglobal.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
While we generally allow scatterlists to have offsets larger than page
size for an entry, and other subsystems like the crypto code make use of
that, the block layer isn't quite ready for that. Flip the switch back
to avoid them for now, and revisit that decision early in a merge window
once the known offenders are fixed.
Fixes: 8a96a0e408 ("block: rewrite blk_bvec_map_sg to avoid a nth_page call")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
commit 2da78092dd "block: Fix dev_t minor allocation lifetime"
specifically moved blk_free_devt(dev->devt) call to part_release()
to avoid reallocating device number before the device is fully
shutdown.
However, it can cause use-after-free on gendisk in get_gendisk().
We use md device as example to show the race scenes:
Process1 Worker Process2
md_free
blkdev_open
del_gendisk
add delete_partition_work_fn() to wq
__blkdev_get
get_gendisk
put_disk
disk_release
kfree(disk)
find part from ext_devt_idr
get_disk_and_module(disk)
cause use after free
delete_partition_work_fn
put_device(part)
part_release
remove part from ext_devt_idr
Before <devt, hd_struct pointer> is removed from ext_devt_idr by
delete_partition_work_fn(), we can find the devt and then access
gendisk by hd_struct pointer. But, if we access the gendisk after
it have been freed, it can cause in use-after-freeon gendisk in
get_gendisk().
We fix this by adding a new helper blk_invalidate_devt() in
delete_partition() and del_gendisk(). It replaces hd_struct
pointer in idr with value 'NULL', and deletes the entry from
idr in part_release() as we do now.
Thanks to Jan Kara for providing the solution and more clear comments
for the code.
Fixes: 2da78092dd ("block: Fix dev_t minor allocation lifetime")
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Suggested-by: Jan Kara <jack@suse.cz>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAly8rGYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGmZMH/1IRB0E1Qmzz8yzw
wj79UuRGYPqxDDSWW+wNc8sU4Ic7iYirn9APHAztCdQqsjmzU/OVLfSa3JhdBe5w
THo7pbGKBqEDcWnKfNk/21jXFNLZ1vr9BoQv2DGU2MMhHAyo/NZbalo2YVtpQPmM
OCRth5n+LzvH7rGrX7RYgWu24G9l3NMfgtaDAXBNXesCGFAjVRrdkU5CBAaabvtU
4GWh/nnutndOOLdByL3x+VZ3H3fIBnbNjcIGCglvvqzk7h3hrfGEl4UCULldTxcM
IFsfMUhSw1ENy7F6DHGbKIG90cdCJcrQ8J/ziEzjj/KLGALluutfFhVvr6YCM2J6
2RgU8CY=
=CfY1
-----END PGP SIGNATURE-----
Merge tag 'v5.1-rc6' into for-5.2/block
Pull in v5.1-rc6 to resolve two conflicts. One is in BFQ, in just a
comment, and is trivial. The other one is a conflict due to a later fix
in the bio multi-page work, and needs a bit more care.
* tag 'v5.1-rc6': (770 commits)
Linux 5.1-rc6
block: make sure that bvec length can't be overflow
block: kill all_q_node in request_queue
x86/cpu/intel: Lower the "ENERGY_PERF_BIAS: Set to normal" message's log priority
coredump: fix race condition between mmget_not_zero()/get_task_mm() and core dumping
mm/kmemleak.c: fix unused-function warning
init: initialize jump labels before command line option parsing
kernel/watchdog_hld.c: hard lockup message should end with a newline
kcov: improve CONFIG_ARCH_HAS_KCOV help text
mm: fix inactive list balancing between NUMA nodes and cgroups
mm/hotplug: treat CMA pages as unmovable
proc: fixup proc-pid-vm test
proc: fix map_files test on F29
mm/vmstat.c: fix /proc/vmstat format for CONFIG_DEBUG_TLBFLUSH=y CONFIG_SMP=n
mm/memory_hotplug: do not unlock after failing to take the device_hotplug_lock
mm: swapoff: shmem_unuse() stop eviction without igrab()
mm: swapoff: take notice of completion sooner
mm: swapoff: remove too limiting SWAP_UNUSE_MAX_TRIES
mm: swapoff: shmem_find_swap_entries() filter out other types
slab: store tagged freelist for off-slab slabmgmt
...
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A previous commit moved the shallow depth and BFQ depth map calculations
to be done at init time, moving it outside of the hotter IO path. This
potentially causes hangs if the users changes the depth of the scheduler
map, by writing to the 'nr_requests' sysfs file for that device.
Add a blk-mq-sched hook that allows blk-mq to inform the scheduler if
the depth changes, so that the scheduler can update its internal state.
Tested-by: Kai Krakow <kai@kaishome.de>
Reported-by: Paolo Valente <paolo.valente@linaro.org>
Fixes: f0635b8a41 ("bfq: calculate shallow depths at init time")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Drivers now report to the block layer if they support media change
events. If this is not the case, there's no need to allocate the event
structure, and all event handling code can effectively be skipped. This
simplifies code flow in particular for non-removable sd devices.
This effectively reverts commit 75e3f3ee3c ("block: always allocate
genhd->ev if check_events is implemented").
The sysfs files for the events are kept in place even if no events are
supported, as user space may rely on them being present. The only
difference is that an error code is now returned if the user tries to
set poll_msecs.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, an empty disk->events field tells the block layer not to
forward media change events to user space. This was done in commit
7c88a168da ("block: don't propagate unlisted DISK_EVENTs to userland")
in order to avoid events from "fringe" drivers to be forwarded to user
space. By doing so, the block layer lost the information which events
were supported by a particular block device, and most importantly,
whether or not a given device supports media change events at all.
Prepare for not interpreting the "events" field this way in the future
any more. This is done by adding an additional field "event_flags" to
struct gendisk, and two flag bits that can be set to have the device
treated like one that had the "events" field set to a non-zero value
before. This applies only to the sd and sr drivers, which are changed to
set the new flags.
The new flags are DISK_EVENT_FLAG_POLL to enforce polling of the device
for synchronous events, and DISK_EVENT_FLAG_UEVENT to tell the
blocklayer to generate udev events from kernel events.
In order to add the event_flags field to struct gendisk, the events
field is converted to an "unsigned short"; it doesn't need to hold
values bigger than 2 anyway.
This patch doesn't change behavior.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The async_events field, intended to be used for drivers that support
asynchronous notifications about disk events (aka media change events),
isn't currently used by any driver, and apparently that has been that
way for a long time (if not forever). Remove it.
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We currently have to call nth_page when iterating over pages inside a
bio_vec. Jens complained a while ago that this is fairly expensive.
To mitigate this we can check that that the actual page structures
are contiguous when adding them to the bio, and just do check pointer
arithmetics later on.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of needing a special macro to iterate over all pages in
a bvec just do a second passs over the whole bio. This also matches
what we do on the release side. The release side helper is moved
up to where we need the get helper to clearly express the symmetry.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
No caller uses bio_iov_iter_get_pages multiple times on a given bio,
and that funtionality isn't all that useful. Removing it will make
some future changes a little easier and also simplifies the function
a bit.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Return early on error, and add an unlikely annotation for that case.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The offset in scatterlists is allowed to be larger than the page size,
so don't go to great length to avoid that case and simplify the
arithmetics.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When bio_add_pc_page() fails in bio_copy_user_iov() we should free
the page we just allocated otherwise we are leaking it.
Cc: linux-block@vger.kernel.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In NVMe's error handler, follows the typical steps of tearing down
hardware for recovering controller:
1) stop blk_mq hw queues
2) stop the real hw queues
3) cancel in-flight requests via
blk_mq_tagset_busy_iter(tags, cancel_request, ...)
cancel_request():
mark the request as abort
blk_mq_complete_request(req);
4) destroy real hw queues
However, there may be race between #3 and #4, because blk_mq_complete_request()
may run q->mq_ops->complete(rq) remotelly and asynchronously, and
->complete(rq) may be run after #4.
This patch introduces blk_mq_complete_request_sync() for fixing the
above race.
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Bart Van Assche <bvanassche@acm.org>
Cc: James Smart <james.smart@broadcom.com>
Cc: linux-nvme@lists.infradead.org
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The function bfq_bfqq_expire() invokes the function
__bfq_bfqq_expire(), and the latter may free the in-service bfq-queue.
If this happens, then no other instruction of bfq_bfqq_expire() must
be executed, or a use-after-free will occur.
Basing on the assumption that __bfq_bfqq_expire() invokes
bfq_put_queue() on the in-service bfq-queue exactly once, the queue is
assumed to be freed if its refcounter is equal to one right before
invoking __bfq_bfqq_expire().
But, since commit 9dee8b3b05 ("block, bfq: fix queue removal from
weights tree") this assumption is false. __bfq_bfqq_expire() may also
invoke bfq_weights_tree_remove() and, since commit 9dee8b3b05
("block, bfq: fix queue removal from weights tree"), also
the latter function may invoke bfq_put_queue(). So __bfq_bfqq_expire()
may invoke bfq_put_queue() twice, and this is the actual case where
the in-service queue may happen to be freed.
To address this issue, this commit moves the check on the refcounter
of the queue right around the last bfq_put_queue() that may be invoked
on the queue.
Fixes: 9dee8b3b05 ("block, bfq: fix queue removal from weights tree")
Reported-by: Dmitrii Tcvetkov <demfloro@demfloro.ru>
Reported-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Dmitrii Tcvetkov <demfloro@demfloro.ru>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit f6970f83ef ("block: don't check if adjacent bvecs in one bio can
be mergeable") changes bvec merge by only considering two bvecs from
different bios. However, if the former bio doesn't inlcude any io bvec,
then the following warning may be triggered:
warning: ‘bvec.bv_offset’ may be used uninitialized in this function [-Wmaybe-uninitialized]
In practice, it shouldn't be triggered.
Fixes it by adding check on former bio, the check shouldn't add any cost
given 'bio->bi_iter' can be hit in cache.
Reported-by: Jens Axboe <axboe@kernel.dk>
Fixes: f6970f83ef ("block: don't check if adjacent bvecs in one bio can be mergeable")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Some of the comments in the bfq files had typos. This patch fixes them.
Signed-off-by: Angelo Ruocco <angeloruocco90@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The 'def' local variable became unused after commit f382fb0bce ("block: remove
legacy IO schedulers"), let's remove it.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Hisao Tanabe <xtanabe@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As the function is responsible for executing the individual steps supplied
in the steps argument, execute_steps is a more descriptive name than the
rather generic next.
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Originally each of the opal functions that call next include
opal_discovery0 in the array of steps. This is superfluous and
can be done always inside next.
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The steps argument is only read by the next function, so it can
be passed directly as an argument rather than via opal_dev.
Normally, the steps is an array on the stack, so the pointer stops
being valid then the function that set opal_dev.steps returns.
If opal_dev.steps was not set to NULL before return it would become
a dangling pointer. When the steps are passed as argument this
becomes easier to see and more difficult to misuse.
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace integer literals by Opal tokens defined in opal_proto.h where
possible.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Instead of having multiple places defining the same argument list to get
a specific column of a sed-opal table, provide a generic version and
call it from those functions.
Co-authored-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Define OPAL_LIFECYCLE token and use it instead of literals in
get_lsp_lifecycle.
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Split the header generation from the (normal) memcpy part if a
bytestring is copied into the command buffer. This allows in-place
generation of the bytestring content. For example, copy_from_user may be
used without an intermediate buffer.
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add function address (and if available its symbol) to the message if a
step function fails.
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
response_get_token had already been in place, its functionality had
been duplicated within response_get_{u64,bytestring} with the same error
handling. Unify the handling by reusing response_get_token within the
other functions.
Co-authored-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
response_get_{string,u64} include error handling for argument resp being
NULL but response_get_token does not handle this.
Make all three of response_get_{string,u64,token} handle NULL resp in
the same way.
Co-authored-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Every step starts with resetting the cmd buffer as well as the comid and
constructs the appropriate OPAL_CALL command. Consequently, those
actions may be combined into one generic function. On should take care
that the opening and closing tokens for the argument list are already
emitted by cmd_start and cmd_finalize respectively and thus must not be
additionally added.
Co-authored-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Every step ends by calling cmd_finalize (via finalize_and_send)
yet every step adds the token OPAL_ENDLIST on its own. Moving
this into cmd_finalize decreases code duplication.
Co-authored-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
All add_token_* functions have a common set of conditions that have to
be checked. Use a common function for those checks in order to avoid
different behaviour as well as code duplication.
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Co-authored-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Also the values of OPAL_UID_LENGTH and OPAL_METHOD_LENGTH are the same,
it is weird to use OPAL_UID_LENGTH for the definition of the methods.
Signed-off-by: Jonas Rabenstein <jonas.rabenstein@studium.uni-erlangen.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This should make no change in functionality.
The formatting changes were triggered by checkpatch.pl.
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The implementation of IOC_OPAL_ENABLE_DISABLE_MBR handled the value
opal_mbr_data.enable_disable incorrectly: enable_disable is expected
to be one of OPAL_MBR_ENABLE(0) or OPAL_MBR_DISABLE(1). enable_disable
was passed directly to set_mbr_done and set_mbr_enable_disable where
is was interpreted as either OPAL_TRUE(1) or OPAL_FALSE(0). The end
result was that calling IOC_OPAL_ENABLE_DISABLE_MBR with OPAL_MBR_ENABLE
actually disabled the shadow MBR and vice versa.
This patch adds correct conversion from OPAL_MBR_DISABLE/ENABLE to
OPAL_FALSE/TRUE. The change affects existing programs using
IOC_OPAL_ENABLE_DISABLE_MBR but this is typically used only once when
setting up an Opal drive.
Acked-by: Jon Derrick <jonathan.derrick@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Scott Bauer <sbauer@plzdonthack.me>
Signed-off-by: David Kozub <zub@linux.fjfi.cvut.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently support for 64-bit sector_t and blkcnt_t is optional on 32-bit
architectures. These types are required to support block device and/or
file sizes larger than 2 TiB, and have generally defaulted to on for
a long time. Enabling the option only increases the i386 tinyconfig
size by 145 bytes, and many data structures already always use
64-bit values for their in-core and on-disk data structures anyway,
so there should not be a large change in dynamic memory usage either.
Dropping this option removes a somewhat weird non-default config that
has cause various bugs or compiler warnings when actually used.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_mq_try_issue_directly() can return BLK_STS*_RESOURCE for requests that
have been queued. If that happens when blk_mq_try_issue_directly() is called
by the dm-mpath driver then dm-mpath will try to resubmit a request that is
already queued and a kernel crash follows. Since it is nontrivial to fix
blk_mq_request_issue_directly(), revert the blk_mq_request_issue_directly()
changes that went into kernel v5.0.
This patch reverts the following commits:
* d6a51a97c0 ("blk-mq: replace and kill blk_mq_request_issue_directly") # v5.0.
* 5b7a6f128a ("blk-mq: issue directly with bypass 'false' in blk_mq_sched_insert_requests") # v5.0.
* 7f556a44e6 ("blk-mq: refactor the code of issue request directly") # v5.0.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Jianchao Wang <jianchao.w.wang@oracle.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: James Smart <james.smart@broadcom.com>
Cc: Dongli Zhang <dongli.zhang@oracle.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: <stable@vger.kernel.org>
Reported-by: Laurence Oberman <loberman@redhat.com>
Tested-by: Laurence Oberman <loberman@redhat.com>
Fixes: 7f556a44e6 ("blk-mq: refactor the code of issue request directly") # v5.0.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With the introduction of BIO_NO_PAGE_REF we've used up all available bits
in bio::bi_flags.
Convert the defines of the flags to an enum and add a BUILD_BUG_ON() call
to make sure no-one adds a new one and thus overrides the BVEC_POOL_IDX
causing crashes.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We would never be able to sort the list if we first reset plug->rq_count
which is used in conditional check later.
Fixes: ce5b009cff ("block: improve logic around when to sort a plug list")
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For now, we just trace plug for single queue device or drivers
provide .commit_rqs, and have not trace plug for multiple queues
device. But, unplug events will be recorded when call
blk_mq_flush_plug_list(). Then, trace events will be asymmetrical,
just have unplug and without plug.
This patch add trace plug and unplug for multiple queues device in
blk_mq_make_request(). After that, we can accurately trace plug and
unplug for multiple queues.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
kfree() can leak the hctx->fq->flush_rq field.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Shenghui Wang <shhuiw@foxmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now both passthrough and FS IO have supported multi-page bvec, and
bvec merging has been handled actually when adding page to bio, then
adjacent bvecs won't be mergeable any more if they belong to same bio.
So only try to merge bvecs if they are from different bios.
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Inside __blk_segment_map_sg(), page sized bvec mapping is optimized
a bit with one standalone branch.
So reuse __blk_bvec_map_sg() to do that.
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The argument of 'request_queue' isn't used by __blk_bvec_map_sg(),
so remove it.
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now block IO stack is basically ready for supporting multi-page bvec,
however it isn't enabled on passthrough IO.
One reason is that passthrough IO is dispatched to LLD directly and bio
split is bypassed, so the bio has to be built correctly for dispatch to
LLD from the beginning.
Implement multi-page support for passthrough IO by limitting each bvec
as block device's segment and applying all kinds of queue limit in
blk_add_pc_page(). Then we don't need to calculate segments any more for
passthrough IO any more, turns out code is simplified much.
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When the added page is merged to last same page in bio_add_pc_page(),
the user may need to put this page for avoiding page leak.
bio_map_user_iov() needs this kind of handling, and now it deals with
it by itself in hack style.
Moves the handling of put page into __bio_add_pc_page(), so
bio_map_user_iov() may be simplified a bit, and maybe more users
can benefit from this change.
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now the check for deciding if one page is mergeable to current bvec
becomes a bit complicated, and we need to reuse the code before
adding pc page.
So move the check in one dedicated helper.
No function change.
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
REQ_PC is out of date, so replace it with passthrough IO.
Also remove the local variable of 'prev' since we can reuse
the top local variable of 'bvec'.
No function change.
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For normal filesystem IO, each page is added via blk_add_page(),
in which bvec(page) merge has been handled already, and basically
not possible to merge two adjacent bvecs in one bio.
So not try to merge two adjacent bvecs in blk_queue_split().
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
XEN has special page merge requirement, see xen_biovec_phys_mergeable().
We can't merge pages into one bvec simply for XEN.
So move XEN's specific check on page merge into __bio_try_merge_page(),
then abvoid to break XEN by multi-page bvec.
Cc: ris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: xen-devel@lists.xenproject.org
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
xen_biovec_phys_mergeable() only needs .bv_page of the 2nd bio bvec
for checking if the two bvecs can be merged, so pass page to
xen_biovec_phys_mergeable() directly.
No function change.
Cc: ris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: xen-devel@lists.xenproject.org
Cc: Omar Sandoval <osandov@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bfq saves the state of a queue each time a merge occurs, to be
able to resume such a state when the queue is associated again
with its original process, on a split.
Unfortunately bfq does not save & restore also the weight of the
queue. If the weight is not correctly resumed when the queue is
recycled, then the weight of the recycled queue could differ
from the weight of the original queue.
This commit adds the missing save & resume of the weight.
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Francesco Pollicino <fra.fra.800@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The function "bfq_log_bfqq" prints the pid of the process
associated with the queue passed as input.
Unfortunately, if the queue is shared, then more than one process
is associated with the queue. The pid that gets printed in this
case is the pid of one of the associated processes.
Which process gets printed depends on the exact sequence of merge
events the queue underwent. So printing such a pid is rather
useless and above all is often rather confusing because it
reports a random pid between those of the associated processes.
This commit addresses this issue by printing SHARED instead of a pid
if the queue is shared.
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Francesco Pollicino <fra.fra.800@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If many bfq_queues belonging to the same group happen to be created
shortly after each other, then the processes associated with these
queues have typically a common goal. In particular, bursts of queue
creations are usually caused by services or applications that spawn
many parallel threads/processes. Examples are systemd during boot, or
git grep. If there are no other active queues, then, to help these
processes get their job done as soon as possible, the best thing to do
is to reach a high throughput. To this goal, it is usually better to
not grant either weight-raising or device idling to the queues
associated with these processes. And this is exactly what BFQ
currently does.
There is however a drawback: if, in contrast, some other queues are
already active, then the newly created queues must be protected from
the I/O flowing through the already existing queues. In this case, the
best thing to do is the opposite as in the other case: it is much
better to grant weight-raising and device idling to the newly-created
queues, if they deserve it. This commit addresses this issue by doing
so if there are already other active queues.
This change also helps eliminating false positives, which occur when
the newly-created queues do not belong to an actual large burst of
creations, but some background task (e.g., a service) happens to
trigger the creation of new queues in the middle, i.e., very close to
when the victim queues are created. These false positive may cause
total loss of control on process latencies.
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sync random I/O is likely to be confused with soft real-time I/O,
because it is characterized by limited throughput and apparently
isochronous arrival pattern. To avoid false positives, this commits
prevents bfq_queues containing only random (seeky) I/O from being
tagged as soft real-time.
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To boost throughput with a set of processes doing interleaved I/O
(i.e., a set of processes whose individual I/O is random, but whose
merged cumulative I/O is sequential), BFQ merges the queues associated
with these processes, i.e., redirects the I/O of these processes into a
common, shared queue. In the shared queue, I/O requests are ordered by
their position on the medium, thus sequential I/O gets dispatched to
the device when the shared queue is served.
Queue merging costs execution time, because, to detect which queues to
merge, BFQ must maintain a list of the head I/O requests of active
queues, ordered by request positions. Measurements showed that this
costs about 10% of BFQ's total per-request processing time.
Request processing time becomes more and more critical as the speed of
the underlying storage device grows. Yet, fortunately, queue merging
is basically useless on the very devices that are so fast to make
request processing time critical. To reach a high throughput, these
devices must have many requests queued at the same time. But, in this
configuration, the internal scheduling algorithms of these devices do
also the job of queue merging: they reorder requests so as to obtain
as much as possible a sequential I/O pattern. As a consequence, with
processes doing interleaved I/O, the throughput reached by one such
device is likely to be the same, with and without queue merging.
In view of this fact, this commit disables queue merging, and all
related housekeeping, for non-rotational devices with internal
queueing. The total, single-lock-protected, per-request processing
time of BFQ drops to, e.g., 1.9 us on an Intel Core i7-2760QM@2.40GHz
(time measured with simple code instrumentation, and using the
throughput-sync.sh script of the S suite [1], in performance-profiling
mode). To put this result into context, the total,
single-lock-protected, per-request execution time of the lightest I/O
scheduler available in blk-mq, mq-deadline, is 0.7 us (mq-deadline is
~800 LOC, against ~10500 LOC for BFQ).
Disabling merging provides a further, remarkable benefit in terms of
throughput. Merging tends to make many workloads artificially more
uneven, mainly because of shared queues remaining non empty for
incomparably more time than normal queues. So, if, e.g., one of the
queues in a set of merged queues has a higher weight than a normal
queue, then the shared queue may inherit such a high weight and, by
staying almost always active, may force BFQ to perform I/O plugging
most of the time. This evidently makes it harder for BFQ to let the
device reach a high throughput.
As a practical example of this problem, and of the benefits of this
commit, we measured again the throughput in the nasty scenario
considered in previous commit messages: dbench test (in the Phoronix
suite), with 6 clients, on a filesystem with journaling, and with the
journaling daemon enjoying a higher weight than normal processes. With
this commit, the throughput grows from ~150 MB/s to ~200 MB/s on a
PLEXTOR PX-256M5 SSD. This is the same peak throughput reached by any
of the other I/O schedulers. As such, this is also likely to be the
maximum possible throughput reachable with this workload on this
device, because I/O is mostly random, and the other schedulers
basically just pass I/O requests to the drive as fast as possible.
[1] https://github.com/Algodev-github/S
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Francesco Pollicino <fra.fra.800@gmail.com>
Signed-off-by: Alessio Masola <alessio.masola@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The processes associated with a bfq_queue, say Q, may happen to
generate their cumulative I/O at a lower rate than the rate at which
the device could serve the same I/O. This is rather probable, e.g., if
only one process is associated with Q and the device is an SSD. It
results in Q becoming often empty while in service. If BFQ is not
allowed to switch to another queue when Q becomes empty, then, during
the service of Q, there will be frequent "service holes", i.e., time
intervals during which Q gets empty and the device can only consume
the I/O already queued in its hardware queues. This easily causes
considerable losses of throughput.
To counter this problem, BFQ implements a request injection mechanism,
which tries to fill the above service holes with I/O requests taken
from other bfq_queues. The hard part in this mechanism is finding the
right amount of I/O to inject, so as to both boost throughput and not
break Q's bandwidth and latency guarantees. To this goal, the current
version of this mechanism measures the bandwidth enjoyed by Q while it
is being served, and tries to inject the maximum possible amount of
extra service that does not cause Q's bandwidth to decrease too
much.
This solution has an important shortcoming. For bandwidth measurements
to be stable and reliable, Q must remain in service for a much longer
time than that needed to serve a single I/O request. Unfortunately,
this does not hold with many workloads. This commit addresses this
issue by changing the way the amount of injection allowed is
dynamically computed. It tunes injection as a function of the service
times of single I/O requests of Q, instead of Q's
bandwidth. Single-request service times are evidently meaningful even
if Q gets very few I/O requests completed while it is in service.
As a testbed for this new solution, we measured the throughput reached
by BFQ for one of the nastiest workloads and configurations for this
scheduler: the workload generated by the dbench test (in the Phoronix
suite), with 6 clients, on a filesystem with journaling, and with the
journaling daemon enjoying a higher weight than normal processes.
With this commit, the throughput grows from ~100 MB/s to ~150 MB/s on
a PLEXTOR PX-256M5.
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Tested-by: Francesco Pollicino <fra.fra.800@gmail.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In most cases, it is detrimental for throughput to plug I/O dispatch
when the in-service bfq_queue becomes temporarily empty (plugging is
performed to wait for the possible arrival, soon, of new I/O from the
in-service queue). There is however a case where plugging is needed
for service guarantees. If a bfq_queue, say Q, has a higher weight
than some other active bfq_queue, and is sync, i.e., contains sync
I/O, then, to guarantee that Q does receive a higher share of the
throughput than other lower-weight queues, it is necessary to plug I/O
dispatch when Q remains temporarily empty while being served.
For this reason, BFQ performs I/O plugging when some active bfq_queue
has a higher weight than some other active bfq_queue. But this is
unnecessarily overkill. In fact, if the in-service bfq_queue actually
has a weight lower than or equal to the other queues, then the queue
*must not* be guaranteed a higher share of the throughput than the
other queues. So, not plugging I/O cannot cause any harm to the
queue. And can boost throughput.
Taking advantage of this fact, this commit does not plug I/O for sync
bfq_queues with a weight lower than or equal to the weights of the
other queues. Here is an example of the resulting throughput boost
with the dbench workload, which is particularly nasty for BFQ. With
the dbench test in the Phoronix suite, BFQ reaches its lowest total
throughput with 6 clients on a filesystem with journaling, in case the
journaling daemon has a higher weight than normal processes. Before
this commit, the total throughput was ~80 MB/sec on a PLEXTOR PX-256M5,
after this commit it is ~100 MB/sec.
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If a sync bfq_queue has a higher weight than some other queue, and
remains temporarily empty while in service, then, to preserve the
bandwidth share of the queue, it is necessary to plug I/O dispatching
until a new request arrives for the queue. In addition, a timeout
needs to be set, to avoid waiting for ever if the process associated
with the queue has actually finished its I/O.
Even with the above timeout, the device is however not fed with new
I/O for a while, if the process has finished its I/O. If this happens
often, then throughput drops and latencies grow. For this reason, the
timeout is kept rather low: 8 ms is the current default.
Unfortunately, such a low value may cause, on the opposite end, a
violation of bandwidth guarantees for a process that happens to issue
new I/O too late. The higher the system load, the higher the
probability that this happens to some process. This is a problem in
scenarios where service guarantees matter more than throughput. One
important case are weight-raised queues, which need to be granted a
very high fraction of the bandwidth.
To address this issue, this commit lower-bounds the plugging timeout
for weight-raised queues to 20 ms. This simple change provides
relevant benefits. For example, on a PLEXTOR PX-256M5S, with which
gnome-terminal starts in 0.6 seconds if there is no other I/O in
progress, the same applications starts in
- 0.8 seconds, instead of 1.2 seconds, if ten files are being read
sequentially in parallel
- 1 second, instead of 2 seconds, if, in parallel, five files are
being read sequentially, and five more files are being written
sequentially
Tested-by: Holger Hoffstätte <holger@applied-asynchrony.com>
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We now wrap sbitmap waitqueues in an active counter, so we can avoid
iterating wakeups unless we have waiters there. This works as long as
everyone that's manipulating the waitqueues use the proper helpers. For
the tag wait case for shared tags, however, we add ourselves to the
waitqueue without incrementing/decrementing the ->ws_active count. This
means that wakeups can take a long time to happen.
Fix this by manually doing the inc/dec as needed for the wait queue
handling.
Reported-by: Michael Leun <kbug@newton.leun.net>
Tested-by: Michael Leun <kbug@newton.leun.net>
Cc: stable@vger.kernel.org
Reviewed-by: Omar Sandoval <osandov@fb.com>
Fixes: 5d2ee7122c ("sbitmap: optimize wakeup check")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For now, blk_mq_hctx_has_pending() checks any of ctx, hctx->dispatch
or io scheduler have pending work. So, update the comment accordingly.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Expect arguments, blk_mq_put_driver_tag_hctx() and blk_mq_put_driver_tag()
is same. We can just use argument 'request' to put tag by blk_mq_put_driver_tag().
Then we can remove the unused blk_mq_put_driver_tag_hctx().
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=l4lx
-----END PGP SIGNATURE-----
Merge tag 'io_uring-20190323' of git://git.kernel.dk/linux-block
Pull io_uring fixes and improvements from Jens Axboe:
"The first five in this series are heavily inspired by the work Al did
on the aio side to fix the races there.
The last two re-introduce a feature that was in io_uring before it got
merged, but which I pulled since we didn't have a good way to have
BVEC iters that already have a stable reference. These aren't
necessarily related to block, it's just how io_uring pins fixed
buffers"
* tag 'io_uring-20190323' of git://git.kernel.dk/linux-block:
block: add BIO_NO_PAGE_REF flag
iov_iter: add ITER_BVEC_FLAG_NO_REF flag
io_uring: mark me as the maintainer
io_uring: retry bulk slab allocs as single allocs
io_uring: fix poll races
io_uring: fix fget/fput handling
io_uring: add prepped flag
io_uring: make io_read/write return an integer
io_uring: use regular request ref counts
Avoid that the following warnings are reported when building with W=1:
block/blk-cgroup.c:1755: warning: Function parameter or member 'q' not described in 'blkcg_schedule_throttle'
block/blk-cgroup.c:1755: warning: Function parameter or member 'use_memdelay' not described in 'blkcg_schedule_throttle'
block/blk-cgroup.c:1779: warning: Function parameter or member 'blkg' not described in 'blkcg_add_delay'
block/blk-cgroup.c:1779: warning: Function parameter or member 'now' not described in 'blkcg_add_delay'
block/blk-cgroup.c:1779: warning: Function parameter or member 'delta' not described in 'blkcg_add_delay'
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch avoids that the following warning is reported when building
with W=1:
block/blk-iolatency.c:734:5: warning: no previous prototype for 'blk_iolatency_init' [-Wmissing-prototypes]
Cc: Josef Bacik <jbacik@fb.com>
Fixes: d706751215 ("block: introduce blk-iolatency io controller") # v4.19
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This function is not used outside the block layer core. Hence unexport it.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For q->poll_nsec == -1, means doing classic poll, not hybrid poll.
We introduce a new flag BLK_MQ_POLL_CLASSIC to replace -1, which
may make code much easier to read.
Additionally, since val is an int obtained with kstrtoint(), val can be
a negative value other than -1, so return -EINVAL for that case.
Thanks to Damien Le Moal for some good suggestion.
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If bio_iov_iter_get_pages() is called on an iov_iter that is flagged
with NO_REF, then we don't need to add a page reference for the pages
that we add.
Add BIO_NO_PAGE_REF to track this in the bio, so IO completion knows
not to drop a reference to these pages.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Let blk_mq_mark_tag_wait() use the blk_mq_sched_mark_restart_hctx()
to set BLK_MQ_S_SCHED_RESTART.
Signed-off-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=qBae
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block
Pull more block layer changes from Jens Axboe:
"This is a collection of both stragglers, and fixes that came in after
I finalized the initial pull. This contains:
- An MD pull request from Song, with a few minor fixes
- Set of NVMe patches via Christoph
- Pull request from Konrad, with a few fixes for xen/blkback
- pblk fix IO calculation fix (Javier)
- Segment calculation fix for pass-through (Ming)
- Fallthrough annotation for blkcg (Mathieu)"
* tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block: (25 commits)
blkcg: annotate implicit fall through
nvme-tcp: support C2HData with SUCCESS flag
nvmet: ignore EOPNOTSUPP for discard
nvme: add proper write zeroes setup for the multipath device
nvme: add proper discard setup for the multipath device
nvme: remove nvme_ns_config_oncs
nvme: disable Write Zeroes for qemu controllers
nvmet-fc: bring Disconnect into compliance with FC-NVME spec
nvmet-fc: fix issues with targetport assoc_list list walking
nvme-fc: reject reconnect if io queue count is reduced to zero
nvme-fc: fix numa_node when dev is null
nvme-fc: use nr_phys_segments to determine existence of sgl
nvme-loop: init nvmet_ctrl fatal_err_work when allocate
nvme: update comment to make the code easier to read
nvme: put ns_head ref if namespace fails allocation
nvme-trace: fix cdw10 buffer overrun
nvme: don't warn on block content change effects
nvme: add get-feature to admin cmds tracer
md: Fix failed allocation of md_register_thread
It's wrong to add len to sector_nr in raid10 reshape twice
...
All users of VM_MAX_READAHEAD actually convert it to kbytes and then to
pages. Define the macro explicitly as (SZ_128K / PAGE_SIZE). This
simplifies the expression in every filesystem. Also rename the macro to
VM_READAHEAD_PAGES to properly convey its meaning. Finally remove unused
VM_MIN_READAHEAD
[akpm@linux-foundation.org: fix fs/io_uring.c, per Stephen]
Link: http://lkml.kernel.org/r/20181221144053.24318-1-nborisov@suse.com
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Cc: Dominique Martinet <asmadeus@codewreck.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: David Sterba <dsterba@suse.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
-----BEGIN PGP SIGNATURE-----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=p78E
-----END PGP SIGNATURE-----
Merge tag 'io_uring-2019-03-06' of git://git.kernel.dk/linux-block
Pull io_uring IO interface from Jens Axboe:
"Second attempt at adding the io_uring interface.
Since the first one, we've added basic unit testing of the three
system calls, that resides in liburing like the other unit tests that
we have so far. It'll take a while to get full coverage of it, but
we're working towards it. I've also added two basic test programs to
tools/io_uring. One uses the raw interface and has support for all the
various features that io_uring supports outside of standard IO, like
fixed files, fixed IO buffers, and polled IO. The other uses the
liburing API, and is a simplified version of cp(1).
This adds support for a new IO interface, io_uring.
io_uring allows an application to communicate with the kernel through
two rings, the submission queue (SQ) and completion queue (CQ) ring.
This allows for very efficient handling of IOs, see the v5 posting for
some basic numbers:
https://lore.kernel.org/linux-block/20190116175003.17880-1-axboe@kernel.dk/
Outside of just efficiency, the interface is also flexible and
extendable, and allows for future use cases like the upcoming NVMe
key-value store API, networked IO, and so on. It also supports async
buffered IO, something that we've always failed to support in the
kernel.
Outside of basic IO features, it supports async polled IO as well.
This particular feature has already been tested at Facebook months ago
for flash storage boxes, with 25-33% improvements. It makes polled IO
actually useful for real world use cases, where even basic flash sees
a nice win in terms of efficiency, latency, and performance. These
boxes were IOPS bound before, now they are not.
This series adds three new system calls. One for setting up an
io_uring instance (io_uring_setup(2)), one for submitting/completing
IO (io_uring_enter(2)), and one for aux functions like registrating
file sets, buffers, etc (io_uring_register(2)). Through the help of
Arnd, I've coordinated the syscall numbers so merge on that front
should be painless.
Jon did a writeup of the interface a while back, which (except for
minor details that have been tweaked) is still accurate. Find that
here:
https://lwn.net/Articles/776703/
Huge thanks to Al Viro for helping getting the reference cycle code
correct, and to Jann Horn for his extensive reviews focused on both
security and bugs in general.
There's a userspace library that provides basic functionality for
applications that don't need or want to care about how to fiddle with
the rings directly. It has helpers to allow applications to easily set
up an io_uring instance, and submit/complete IO through it without
knowing about the intricacies of the rings. It also includes man pages
(thanks to Jeff Moyer), and will continue to grow support helper
functions and features as time progresses. Find it here:
git://git.kernel.dk/liburing
Fio has full support for the raw interface, both in the form of an IO
engine (io_uring), but also with a small test application (t/io_uring)
that can exercise and benchmark the interface"
* tag 'io_uring-2019-03-06' of git://git.kernel.dk/linux-block:
io_uring: add a few test tools
io_uring: allow workqueue item to handle multiple buffered requests
io_uring: add support for IORING_OP_POLL
io_uring: add io_kiocb ref count
io_uring: add submission polling
io_uring: add file set registration
net: split out functions related to registering inflight socket files
io_uring: add support for pre-mapped user IO buffers
block: implement bio helper to add iter bvec pages to bio
io_uring: batch io_kiocb allocation
io_uring: use fget/fput_many() for file references
fs: add fget_many() and fput_many()
io_uring: support for IO polling
io_uring: add fsync support
Add io_uring IO interface
-----BEGIN PGP SIGNATURE-----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=VBaU
-----END PGP SIGNATURE-----
Merge tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"Not a huge amount of changes in this round, the biggest one is that we
finally have Mings multi-page bvec support merged. Apart from that,
this pull request contains:
- Small series that avoids quiescing the queue for sysfs changes that
match what we currently have (Aleksei)
- Series of bcache fixes (via Coly)
- Series of lightnvm fixes (via Mathias)
- NVMe pull request from Christoph. Nothing major, just SPDX/license
cleanups, RR mp policy (Hannes), and little fixes (Bart,
Chaitanya).
- BFQ series (Paolo)
- Save blk-mq cpu -> hw queue mapping, removing a pointer indirection
for the fast path (Jianchao)
- fops->iopoll() added for async IO polling, this is a feature that
the upcoming io_uring interface will use (Christoph, me)
- Partition scan loop fixes (Dongli)
- mtip32xx conversion from managed resource API (Christoph)
- cdrom registration race fix (Guenter)
- MD pull from Song, two minor fixes.
- Various documentation fixes (Marcos)
- Multi-page bvec feature. This brings a lot of nice improvements
with it, like more efficient splitting, larger IOs can be supported
without growing the bvec table size, and so on. (Ming)
- Various little fixes to core and drivers"
* tag 'for-5.1/block-20190302' of git://git.kernel.dk/linux-block: (117 commits)
block: fix updating bio's front segment size
block: Replace function name in string with __func__
nbd: propagate genlmsg_reply return code
floppy: remove set but not used variable 'q'
null_blk: fix checking for REQ_FUA
block: fix NULL pointer dereference in register_disk
fs: fix guard_bio_eod to check for real EOD errors
blk-mq: use HCTX_TYPE_DEFAULT but not 0 to index blk_mq_tag_set->map
block: optimize bvec iteration in bvec_iter_advance
block: introduce mp_bvec_for_each_page() for iterating over page
block: optimize blk_bio_segment_split for single-page bvec
block: optimize __blk_segment_map_sg() for single-page bvec
block: introduce bvec_nth_page()
iomap: wire up the iopoll method
block: add bio_set_polled() helper
block: wire up block device iopoll method
fs: add an iopoll method to struct file_operations
loop: set GENHD_FL_NO_PART_SCAN after blkdev_reread_part()
loop: do not print warn message if partition scan is successful
block: bounce: make sure that bvec table is updated
...
blk_recount_segments() can be called in bio_add_pc_page() for
calculating how many segments this bio will has after one page is added
to this bio. If the resulted segment number is beyond the queue limit,
the added page will be removed.
The try-and-fix policy requires blk_recount_segments(__blk_recalc_rq_segments)
to not consider the segment number limit. Unfortunately bvec_split_segs()
does check this limit, and causes small segment number returned to
bio_add_pc_page(), then page still may be added to the bio even though
segment number limit becomes broken.
Fixes this issue by not considering segment number limit when calcualting
bio's segment number.
Fixes: dcebd75592 ("block: use bio_for_each_bvec() to compute multi-page bvec count")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When the current bvec can be merged to the 1st segment, the bio's front
segment size has to be updated.
However, dcebd75592 doesn't consider that case, then bio's front
segment size may not be correct.
This patch fixes this issue.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Omar Sandoval <osandov@fb.com>
Fixes: dcebd75592 ("block: use bio_for_each_bvec() to compute multi-page bvec count")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Replace hard coded function name register_blkdev with __func__, to
improve robustness and to conform to the Linux kernel coding
style. Issue found using checkpatch.
Signed-off-by: Keyur Patel <iamkeyur96@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If __device_add_disk-->bdi_register_owner-->bdi_register-->
bdi_register_va-->device_create_vargs fails, bdi->dev is still
NULL, __device_add_disk-->register_disk will visit bdi->dev->kobj.
This patch fixes that.
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For an ITER_BVEC, we can just iterate the iov and add the pages
to the bio directly. For now, we grab a reference to those pages,
and release them normally on IO completion. This isn't really needed
for the normal case of O_DIRECT from/to a file, but some of the more
esoteric use cases (like splice(2)) will unconditionally put the
pipe buffer pages when the buffers are released. Until we can manage
that case properly, ITER_BVEC pages are treated like normal pages
in terms of reference counting.
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce a fast path for single-page bvec IO, then we can avoid
to call bvec_split_segs() unnecessarily.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Introduce a fast path for single-page bvec IO, then blk_bvec_map_sg()
can be avoided.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Single-page bvec can often be seen in small BS workloads, so
introduce bvec_nth_page() for avoiding to call nth_page() unnecessarily,
which looks not cheap.
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Block bounce needs to allocate new page for doing IO, and the
new page has to be updated to bvec table.
Commit 6dc4f100c switches __blk_queue_bounce() to use the new
bio_for_each_segment_all() interface. Unfortunately the new
bio_for_each_segment_all() can't be used to update bvec table.
This patch fixes this issue by retrieving bvec from the table
directly, then the new allocated page can be updated to the bio.
This way is safe because the cloned bio is single page bvec.
Fixes: 6dc4f100c ("block: allow bio_for_each_segment_all() to iterate over multi-page bvec")
Cc: Christoph Hellwig <hch@lst.de>
Cc: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
rq->bio can be NULL sometimes, such as flush request, so don't
read bio->bi_seg_front_size until this 'bio' is checked as valid.
Cc: Bart Van Assche <bvanassche@acm.org>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Fixes: dcebd75592 ("block: use bio_for_each_bvec() to compute multi-page bvec count")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=8mjO
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190215' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- Ensure we insert into the hctx dispatch list, if a request is marked
as DONTPREP (Jianchao)
- NVMe pull request, single missing unlock on error fix (Keith)
- MD pull request, single fix for a potentially data corrupting issue
(Nate)
- Floppy check_events regression fix (Yufen)
* tag 'for-linus-20190215' of git://git.kernel.dk/linux-block:
md/raid1: don't clear bitmap bits on interrupted recovery.
floppy: check_events callback should not return a negative number
nvme-pci: add missing unlock for reset error
blk-mq: insert rq with DONTPREP to hctx dispatch list when requeue
-----BEGIN PGP SIGNATURE-----
iQFRBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAlxgqNUeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGwsoH+OVXu0NQofwTvVru
8lgF3BSDG2mhf7mxbBBlBizGVy9jnjRNGCFMC+Jq8IwiFLwprja/G27kaDTkpuF1
PHC3yfjKvjTeUP5aNdHlmxv6j1sSJfZl0y46DQal4UeTG/Giq8TFTi+Tbz7Wb/WV
yCx4Lr8okAwTuNhnL8ojUCVIpd3c8QsyR9v6nEQ14Mj+MvEbokyTkMJV0bzOrM38
JOB+/X1XY4JPZ6o3MoXrBca3bxbAJzMneq+9CWw1U5eiIG3msg4a+Ua3++RQMDNr
8BP0yCZ6wo32S8uu0PI6HrZaBnLYi5g9Wh7Q7yc0mn1Uh1zWFykA6TtqK90agJeR
A6Ktjw==
=scY4
-----END PGP SIGNATURE-----
Merge tag 'v5.0-rc6' into for-5.1/block
Pull in 5.0-rc6 to avoid a dumb merge conflict with fs/iomap.c.
This is needed since io_uring is now based on the block branch,
to avoid a conflict between the multi-page bvecs and the bits
of io_uring that touch the core block parts.
* tag 'v5.0-rc6': (525 commits)
Linux 5.0-rc6
x86/mm: Make set_pmd_at() paravirt aware
MAINTAINERS: Update the ocores i2c bus driver maintainer, etc
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
MAINTAINERS: unify reference to xen-devel list
x86/mm/cpa: Fix set_mce_nospec()
futex: Handle early deadlock return correctly
futex: Fix barrier comment
net: dsa: b53: Fix for failure when irq is not defined in dt
blktrace: Show requests without sector
mips: cm: reprime error cause
mips: loongson64: remove unreachable(), fix loongson_poweroff().
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
KVM: nVMX: unconditionally cancel preemption timer in free_nested (CVE-2019-7221)
KVM: x86: work around leak of uninitialized stack contents (CVE-2019-7222)
kvm: fix kvm_ioctl_create_device() reference counting (CVE-2019-6974)
signal: Better detection of synchronous signals
...
QUEUE_FLAG_NO_SG_MERGE has been killed, so kill BLK_MQ_F_SG_MERGE too.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since bdced438ac ("block: setup bi_phys_segments after splitting"),
physical segment number is mainly figured out in blk_queue_split() for
fast path, and the flag of BIO_SEG_VALID is set there too.
Now only blk_recount_segments() and blk_recalc_rq_segments() use this
flag.
Basically blk_recount_segments() is bypassed in fast path given BIO_SEG_VALID
is set in blk_queue_split().
For another user of blk_recalc_rq_segments():
- run in partial completion branch of blk_update_request, which is an unusual case
- run in blk_cloned_rq_check_limits(), still not a big problem if the flag is killed
since dm-rq is the only user.
Multi-page bvec is enabled now, not doing S/G merging is rather pointless with the
current setup of the I/O path, as it isn't going to save you a significant amount
of cycles.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch pulls the trigger for multi-page bvecs.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch introduces one extra iterator variable to bio_for_each_segment_all(),
then we can allow bio_for_each_segment_all() to iterate over multi-page bvec.
Given it is just one mechannical & simple change on all bio_for_each_segment_all()
users, this patch does tree-wide change in one single patch, so that we can
avoid to use a temporary helper for this conversion.
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is more efficient to use bio_for_each_bvec() to map sg, meantime
we have to consider splitting multipage bvec as done in blk_bio_segment_split().
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
First it is more efficient to use bio_for_each_bvec() in both
blk_bio_segment_split() and __blk_recalc_rq_segments() to compute how
many multi-page bvecs there are in the bio.
Secondly once bio_for_each_bvec() is used, the bvec may need to be
splitted because its length can be very longer than max segment size,
so we have to split the big bvec into several segments.
Thirdly when splitting multi-page bvec into segments, the max segment
limit may be reached, so the bio split need to be considered under
this situation too.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It is wrong to use bio->bi_vcnt to figure out how many segments
there are in the bio even though CLONED flag isn't set on this bio,
because this bio may be splitted or advanced.
So always use bio_segments() in blk_recount_segments(), and it shouldn't
cause any performance loss now because the physical segment number is figured
out in blk_queue_split() and BIO_SEG_VALID is set meantime since
bdced438ac ("block: setup bi_phys_segments after splitting").
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Fixes: 76d8137a31 ("blk-merge: recaculate segment if it isn't less than max segments")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When requeue, if RQF_DONTPREP, rq has contained some driver
specific data, so insert it to hctx dispatch list to avoid any
merge. Take scsi as example, here is the trace event log (no
io scheduler, because RQF_STARTED would prevent merging),
kworker/0:1H-339 [000] ...1 2037.209289: block_rq_insert: 8,0 R 4096 () 32768 + 8 [kworker/0:1H]
scsi_inert_test-1987 [000] .... 2037.220465: block_bio_queue: 8,0 R 32776 + 8 [scsi_inert_test]
scsi_inert_test-1987 [000] ...2 2037.220466: block_bio_backmerge: 8,0 R 32776 + 8 [scsi_inert_test]
kworker/0:1H-339 [000] .... 2047.220913: block_rq_issue: 8,0 R 8192 () 32768 + 16 [kworker/0:1H]
scsi_inert_test-1996 [000] ..s1 2047.221007: block_rq_complete: 8,0 R () 32768 + 8 [0]
scsi_inert_test-1996 [000] .Ns1 2047.221045: block_rq_requeue: 8,0 R () 32776 + 8 [0]
kworker/0:1H-339 [000] ...1 2047.221054: block_rq_insert: 8,0 R 4096 () 32776 + 8 [kworker/0:1H]
kworker/0:1H-339 [000] ...1 2047.221056: block_rq_issue: 8,0 R 4096 () 32776 + 8 [kworker/0:1H]
scsi_inert_test-1986 [000] ..s1 2047.221119: block_rq_complete: 8,0 R () 32776 + 8 [0]
(32768 + 8) was requeued by scsi_queue_insert and had RQF_DONTPREP.
Then it was merged with (32776 + 8) and issued. Due to RQF_DONTPREP,
the sdb only contained the part of (32768 + 8), then only that part
was completed. The lucky thing was that scsi_io_completion detected
it and requeued the remaining part. So we didn't get corrupted data.
However, the requeue of (32776 + 8) is not expected.
Suggested-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There's no reason to freeze queue and remove scheduler
if there's no scheduler already.
Signed-off-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There's no reason to set wbt min lat and freeze request queue
if current value is the same.
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The Notes section of the comment was removed, because now
blk_release_queue can only be executed from blk_cleanup_queue (being
called when the q->kobj reaches zero), and also blk_init_queue was removed
in a1ce35fa49.
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since 4cf6324b17, a portion of function blk_cleanup_queue was moved to
a newly created function called blk_exit_queue, including the call of
blkcg_exit_queue. So, adjust the documenation according.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have various helpers for setting/clearing this flag, and also
a helper to check if the queue supports queueable flushes or not.
But nobody uses them anymore, kill it with fire.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=tuL6
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20190209' of git://git.kernel.dk/linux-block
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph, fixing namespace locking when
dealing with the effects log, and a rapid add/remove issue (Keith)
- blktrace tweak, ensuring requests with -1 sectors are shown (Jan)
- link power management quirk for a Smasung SSD (Hans)
- m68k nfblock dynamic major number fix (Chengguang)
- series fixing blk-iolatency inflight counter issue (Liu)
- ensure that we clear ->private when setting up the aio kiocb (Mike)
- __find_get_block_slow() rate limit print (Tetsuo)
* tag 'for-linus-20190209' of git://git.kernel.dk/linux-block:
blk-mq: remove duplicated definition of blk_mq_freeze_queue
Blk-iolatency: warn on negative inflight IO counter
blk-iolatency: fix IO hang due to negative inflight counter
blktrace: Show requests without sector
fs: ratelimit __find_get_block_slow() failure message.
m68k: set proper major_num when specifying module param major_num
libata: Add NOLPM quirk for SAMSUNG MZ7TE512HMHP-000L1 SSD
nvme-pci: fix rapid add remove sequence
nvme: lock NS list changes while handling command effects
aio: initialize kiocb private in case any filesystems expect it.
There's no reason to freeze queue and set nr_requests value
if current value is the same.
Signed-off-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
As the prototype has been defined in "include/linux/blk-mq.h", the one
in "block/blk-mq.h" can be removed then.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is to catch any unexpected negative value of inflight IO counter.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Our test reported the following stack, and vmcore showed that
->inflight counter is -1.
[ffffc9003fcc38d0] __schedule at ffffffff8173d95d
[ffffc9003fcc3958] schedule at ffffffff8173de26
[ffffc9003fcc3970] io_schedule at ffffffff810bb6b6
[ffffc9003fcc3988] blkcg_iolatency_throttle at ffffffff813911cb
[ffffc9003fcc3a20] rq_qos_throttle at ffffffff813847f3
[ffffc9003fcc3a48] blk_mq_make_request at ffffffff8137468a
[ffffc9003fcc3b08] generic_make_request at ffffffff81368b49
[ffffc9003fcc3b68] submit_bio at ffffffff81368d7d
[ffffc9003fcc3bb8] ext4_io_submit at ffffffffa031be00 [ext4]
[ffffc9003fcc3c00] ext4_writepages at ffffffffa03163de [ext4]
[ffffc9003fcc3d68] do_writepages at ffffffff811c49ae
[ffffc9003fcc3d78] __filemap_fdatawrite_range at ffffffff811b6188
[ffffc9003fcc3e30] filemap_write_and_wait_range at ffffffff811b6301
[ffffc9003fcc3e60] ext4_sync_file at ffffffffa030cee8 [ext4]
[ffffc9003fcc3ea8] vfs_fsync_range at ffffffff8128594b
[ffffc9003fcc3ee8] do_fsync at ffffffff81285abd
[ffffc9003fcc3f18] sys_fsync at ffffffff81285d50
[ffffc9003fcc3f28] do_syscall_64 at ffffffff81003c04
[ffffc9003fcc3f50] entry_SYSCALL_64_after_swapgs at ffffffff81742b8e
The ->inflight counter may be negative (-1) if
1) blk-iolatency was disabled when the IO was issued,
2) blk-iolatency was enabled before this IO reached its endio,
3) the ->inflight counter is decreased from 0 to -1 in endio()
In fact the hang can be easily reproduced by the below script,
H=/sys/fs/cgroup/unified/
P=/sys/fs/cgroup/unified/test
echo "+io" > $H/cgroup.subtree_control
mkdir -p $P
echo $$ > $P/cgroup.procs
xfs_io -f -d -c "pwrite 0 4k" /dev/sdg
echo "`cat /sys/block/sdg/dev` target=1000000" > $P/io.latency
xfs_io -f -d -c "pwrite 0 4k" /dev/sdg
This fixes the problem by freezing the queue so that while
enabling/disabling iolatency, there is no inflight rq running.
Note that quiesce_queue is not needed as this only updating iolatency
configuration about which dispatching request_queue doesn't care.
Signed-off-by: Liu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Here are some driver core fixes for 5.0-rc6.
Well, not so much "driver core" as "debugfs". There's a lot of
outstanding debugfs cleanup patches coming in through different
subsystem trees, and in that process the debugfs core was found that it
really should return errors when something bad happens, to prevent
random files from showing up in the root of debugfs afterward. So
debugfs was fixed up to handle this properly, and then two fixes for
the relay and blk-mq code was needed as it was making invalid
assumptions about debugfs return values.
There's also a cacheinfo fix in here that resolves a tiny issue.
All of these have been in linux-next for over a week with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXF069g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk0+gCgy9PTVAJR5ZbYtWTJOTdBnd7pfqMAoMuGxc+6
LLEbfSykLRxEf5SeOJun
=KP8e
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core fixes for 5.0-rc6.
Well, not so much "driver core" as "debugfs". There's a lot of
outstanding debugfs cleanup patches coming in through different
subsystem trees, and in that process the debugfs core was found that
it really should return errors when something bad happens, to prevent
random files from showing up in the root of debugfs afterward. So
debugfs was fixed up to handle this properly, and then two fixes for
the relay and blk-mq code was needed as it was making invalid
assumptions about debugfs return values.
There's also a cacheinfo fix in here that resolves a tiny issue.
All of these have been in linux-next for over a week with no reported
problems"
* tag 'driver-core-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
blk-mq: protect debugfs_create_files() from failures
relay: check return of create_buf_file() properly
debugfs: debugfs_lookup() should return NULL if not found
debugfs: return error values, not NULL
debugfs: fix debugfs_rename parameter checking
cacheinfo: Keep the old value if of_property_read_u32 fails
Unused now, and another field in struct request bites the dust.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No users left.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We can just stash away the second request in struct bsg_job instead of
using the block layer req->next_rq field, allowing for the eventual removal
of the latter.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Move all actual functionality into helpers, just leaving the dispatch in
this function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Tested-by: Benjamin Block <bblock@linux.ibm.com>
Tested-by: Avri Altman <avri.altman@wdc.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, we check whether the hctx type is supported every time
in hot path. Actually, this is not necessary, we could save the
default hctx into ctx->hctxs if the type is not supported when
map swqueues and use it directly with ctx->hctxs[type].
We also needn't check whether the poll is enabled or not, because
the caller would clear the REQ_HIPRI in that case.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Currently, the queue mapping result is saved in a two-dimensional
array. In the hot path, to get a hctx, we need do following:
q->queue_hw_ctx[q->tag_set->map[type].mq_map[cpu]]
This isn't very efficient. We could save the queue mapping result into
ctx directly with different hctx type, like,
ctx->hctxs[type]
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a new I/O request arrives for a bfq_queue, say Q, bfq checks
whether that request is close to
(a) the head request of some other queue waiting to be served, or
(b) the last request dispatched for the in-service queue (in case Q
itself is not the in-service queue)
If a queue, say Q2, is found for which the above condition holds, then
bfq merges Q and Q2, to hopefully get a more sequential I/O in the
resulting merged queue, and thus a possibly higher throughput.
Case (b) is checked by comparing the new request for Q with the last
request dispatched, assuming that the latter necessarily belonged to the
in-service queue. Unfortunately, this assumption is no longer always
correct, since commit d0edc2473b ("block, bfq: inject other-queue I/O
into seeky idle queues on NCQ flash").
When the assumption does not hold, queues that must not be merged may be
merged, causing unexpected loss of control on per-queue service
guarantees.
This commit solves this problem by adding an extra field, which stores
the actual last request dispatched for the in-service queue, and by
using this new field to correctly check case (b).
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Writes tend to starve reads. bfq counters this problem by overcharging
writes with an inflated service w.r.t. the actual service (number of
sector written) they receive.
Yet his overcharging is useless, and actually causes unfairness in the
opposite direction, when bfq happens to be enforcing strong I/O control.
bfq does this enforcing when the scenario is asymmetric, i.e., when some
bfq_queue or group of bfq_queues is to be granted a different bandwidth
than some other bfq_queue or group of bfq_queues. So, in such a
scenario, this commit disables write overcharging.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The original commit is commit 1a1238a7dd ("cfq-iosched: improve hw_tag
detection") and has the following commit message:
If active queue hasn't enough requests and idle window opens, cfq will
not dispatch sufficient requests to hardware. In such situation, current
code will zero hw_tag. But this is because cfq doesn't dispatch enough
requests instead of hardware queue doesn't work. Don't zero hw_tag in
such case.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bfq simple heuristic from cfq for detecting whether the drive performs
command queueing: check whether the average number of in-flight requests
is above a given threshold. Unfortunately this heuristic does fail to
detect queueing (on drives with queueing) if processes doing I/O are few
and issue I/O with a low depth.
To reduce false negatives, this commit lowers the threshold.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bfq maintains an ordered list, through a red-black tree, of unique
weights of active bfq_queues. This list is used to detect whether there
are active queues with differentiated weights. The weight of a queue is
removed from the list when both the following two conditions become
true:
(1) the bfq_queue is flagged as inactive
(2) the has no in-flight request any longer;
Unfortunately, in the rare cases where condition (2) becomes true before
condition (1), the removal fails, because the function to remove the
weight of the queue (bfq_weights_tree_remove) is rightly invoked in the
path that deactivates the bfq_queue, but mistakenly invoked *before* the
function that actually performs the deactivation (bfq_deactivate_bfqq).
This commits moves the invocation of bfq_weights_tree_remove for
condition (1) to after bfq_deactivate_bfqq. As a consequence of this
move, it is necessary to add a further reference to the queue when the
weight of a queue is added, because the queue might otherwise be freed
before bfq_weights_tree_remove is invoked. This commit adds this
reference and makes all related modifications.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In bfq_update_peak_rate, to check whether an I/O request rq is
sequential, only the seek distance of rq w.r.t. the last request
dispatched is controlled. This is not sufficient for non-rotational
storage, where the size of rq is at least as relevant. This commit adds
the missing control.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bfq detects the creation of multiple bfq_queues shortly after each
other, namely a burst of queue creations in the terminology used in the
code. If the burst is large, then no queue in the burst is granted
- either I/O-dispatch plugging when the queue remains temporarily idle
while in service;
- or weight raising, because it causes even longer plugging.
In fact, such a plugging tends to lower throughput, while these bursts
are typically due to applications or services that spawn multiple
processes, to reach a common goal as soon as possible. Examples are a
"git grep" or the booting of a system.
Unfortunately, disabling plugging may cause a loss of service guarantees
in asymmetric scenarios, i.e., if queue weights are differentiated or if
more than one group is active.
This commit addresses this issue by no longer disabling I/O-dispatch
plugging for queues in large bursts.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If the in-service bfq_queue is sync and remains temporarily idle, then
I/O dispatching (from other queues) may be plugged. It may be dome for
two reasons: either to boost throughput, or to preserve the bandwidth
share of the in-service queue. In the first case, if the I/O of the
in-service queue, when it finally arrives, consists only of one small
I/O request, then it makes sense to plug even the I/O of the in-service
queue. In fact, serving such a small request immediately is likely to
lower throughput instead of boosting it, whereas waiting a little bit is
likely to let that request grow, thanks to request merging, and become
more profitable in terms of throughput (this is likely to happen exactly
because the I/O of the queue has been detected to boost throughput).
On the opposite end, if I/O dispatching is being plugged only to
preserve the bandwidth of the in-service queue, then it would be better
not to plug also the I/O of the in-service queue, because such a
plugging is likely to cause only loss of bandwidth for the queue.
Unfortunately, no distinction is made between the two cases, and the I/O
of the in-service queue is always plugged in case just a small I/O
request arrives. This commit draws this missing distinction and does not
perform harmful plugging.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This is a preparatory commit for commits that need to check only one of
the two main reasons for idling. This change should also improve the
quality of the code a little bit, by splitting a function that contains
very long, non-trivial and little related comments.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
In asymmetric scenarios, i.e., when some bfq_queue or bfq_group needs to
be guaranteed a different bandwidth than other bfq_queues or bfq_groups,
these service guaranteed can be provided only by plugging I/O dispatch,
completely or partially, when the queue in service remains temporarily
empty. A case where asymmetry is particularly strong is when some active
bfq_queues belong to a higher-priority class than some other active
bfq_queues. Unfortunately, this important case is not considered at all
in the code for detecting asymmetric scenarios. This commit adds the
missing logic.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Before commit 18e5a57d79 ("block, bfq: postpone rq preparation to
insert or merge"), the destination queue for a request was chosen by a
different hook than the one that then inserted the request. So, between
the execution of the two hooks, the bic of the process generating the
request could happen to be redirected to a different bfq_queue. As a
consequence, the destination bfq_queue stored in the request could be
wrong. Such an event does not need to ba handled any longer.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With some unlucky sequences of events, the function bfq_updated_next_req
updates the current budget of a bfq_queue to a lower value than the
service received by the queue using such a budget. Unfortunately, if
this happens, then the return value of the function bfq_bfqq_budget_left
becomes inconsistent. This commit solves this problem by lower-bounding
the budget computed in bfq_updated_next_req to the service currently
charged to the queue.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
To boost throughput on devices with internal queueing and in scenarios
where device idling is not strictly needed, bfq immediately starts
serving a new bfq_queue if the in-service bfq_queue remains without
pending I/O, even if new I/O may arrive soon for the latter queue. Then,
if such I/O actually arrives soon, bfq preempts the new in-service
bfq_queue so as to give the previous queue a chance to go on being
served (in case the previous queue should actually be the one to be
served, according to its timestamps).
However, the in-service bfq_queue, say Q, may also be without further
budget when it remains also pending I/O. Since bfq changes budgets
dynamically to fit the needs of bfq_queues, this happens more often than
one may expect. If this happens, then there is no point in trying to go
on serving Q when new I/O arrives for it soon: Q would be expired
immediately after being selected for service. This would only cause
useless overhead. This commit avoids such a useless selection.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The speed at which a bfq_queue receives I/O is one of the parameters by
which bfq decides whether the queue is soft real-time (i.e., whether the
queue contains the I/O of a soft real-time application). In particular,
when a bfq_queue remains without outstanding I/O requests, bfq computes
the minimum time instant, named soft_rt_next_start, at which the next
request of the queue may arrive for the queue to be deemed as soft real
time.
Unfortunately this filtering may cause problems with a queue in
interactive weight raising. In fact, such a queue may be conveying the
I/O needed to load a soft real-time application. The latter will
actually exhibit a soft real-time I/O pattern after it finally starts
doing its job. But, if soft_rt_next_start is updated for an interactive
bfq_queue, and the queue has received a lot of service before remaining
with no outstanding request (likely to happen on a fast device), then
soft_rt_next_start is assigned such a high value that, for a very long
time, the queue is prevented from being possibly considered as soft real
time.
This commit removes the updating of soft_rt_next_start for bfq_queues in
interactive weight raising.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If debugfs were to return a non-NULL error for a debugfs call, using
that pointer later in debugfs_create_files() would crash.
Fix that by properly checking the pointer before referencing it.
Reported-by: Michal Hocko <mhocko@kernel.org>
Reported-and-tested-by: syzbot+b382ba6a802a3d242790@syzkaller.appspotmail.com
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Florian reported a io hung issue when fsync(). It should be
triggered by following race condition.
data + post flush a flush
blk_flush_complete_seq
case REQ_FSEQ_DATA
blk_flush_queue_rq
issued to driver blk_mq_dispatch_rq_list
try to issue a flush req
failed due to NON-NCQ command
.queue_rq return BLK_STS_DEV_RESOURCE
request completion
req->end_io // doesn't check RESTART
mq_flush_data_end_io
case REQ_FSEQ_POSTFLUSH
blk_kick_flush
do nothing because previous flush
has not been completed
blk_mq_run_hw_queue
insert rq to hctx->dispatch
due to RESTART is still set, do nothing
To fix this, replace the blk_mq_run_hw_queue in mq_flush_data_end_io
with blk_mq_sched_restart to check and clear the RESTART flag.
Fixes: bd166ef1 (blk-mq-sched: add framework for MQ capable IO schedulers)
Reported-by: Florian Stecker <m19@florianstecker.de>
Tested-by: Florian Stecker <m19@florianstecker.de>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
syzbot is hitting flush_work() warning caused by commit 4d43d395fe
("workqueue: Try to catch flush_work() without INIT_WORK().") [1].
Although that commit did not expect INIT_WORK(NULL) case, calling
flush_work() without setting a valid callback should be avoided anyway.
Fix this problem by setting a no-op callback instead of NULL.
[1] https://syzkaller.appspot.com/bug?id=e390366bc48bc82a7c668326e0663be3b91cbd29
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reported-and-tested-by: syzbot <syzbot+ba2a929dcf8e704c180e@syzkaller.appspotmail.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We can't touch a bio after ->make_request_fn(), for all we know it could
already have been completed by the time this function returns.
This reverts commit 698cef1739.
Reported-by: syzbot+4df6ca820108fd248943@syzkaller.appspotmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch avoids that sparse reports the following warnings:
CHECK block/blk-wbt.c
block/blk-wbt.c:600:6: warning: symbol 'wbt_issue' was not declared. Should it be static?
block/blk-wbt.c:620:6: warning: symbol 'wbt_requeue' was not declared. Should it be static?
CC block/blk-wbt.o
block/blk-wbt.c:600:6: warning: no previous prototype for wbt_issue [-Wmissing-prototypes]
void wbt_issue(struct rq_qos *rqos, struct request *rq)
^~~~~~~~~
block/blk-wbt.c:620:6: warning: no previous prototype for wbt_requeue [-Wmissing-prototypes]
void wbt_requeue(struct rq_qos *rqos, struct request *rq)
^~~~~~~~~~~
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Swap REQ_NOWAIT and REQ_NOUNMAP and add REQ_HIPRI.
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Except for blk_queue_split(), bio_split() is used for splitting bio too,
then the remained bio is often resubmit to queue via generic_make_request().
So the same queue enter recursion exits in this case too. Unfortunatley
commit cd4a4ae468 doesn't help this case.
This patch covers the above case by setting BIO_QUEUE_ENTERED before calling
q->make_request_fn.
In theory the per-bio flag is used to simulate one stack variable, it is
just fine to clear it after q->make_request_fn is returned. Especially
the same bio can't be submitted from another context.
Fixes: cd4a4ae468 ("block: don't use blocking queue entered for recursive bio submits")
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: NeilBrown <neilb@suse.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Remove the imprecise and sloppy:
"This files is licensed under the GPL."
license notice in the top level comment.
1) The file already contains a SPDX license identifier which clearly
states that the license of the file is GPL V2 only
2) The notice resolves to GPL v1 or later for scanners which is just
contrary to the intent of SPDX identifiers to provide clear and non
ambiguous license information. Aside of that the value add of this
notice is below zero,
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Matias Bjorling <mb@lightnvm.io>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: linux-block@vger.kernel.org
Fixes: 6a5ac98465 ("block: Make struct request_queue smaller for CONFIG_BLK_DEV_ZONED=n")
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We need to pass bio->bi_opf after bio intergrity preparing, otherwise
the flag of REQ_INTEGRITY may not be set on the allocated request, then
breaks block integrity.
Fixes: f9afca4d36 ("blk-mq: pass in request/bio flags to queue mapping")
Cc: Hannes Reinecke <hare@suse.com>
Cc: Keith Busch <keith.busch@intel.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Comments on function __bfq_deactivate_entity contains two imprecise or
wrong statements:
1) The function performs the deactivation of the entity.
2) The function must be invoked only if the entity is on a service tree.
This commits replaces both statements with the correct ones:
1) The functions updates sched_data and service trees for the entity,
so as to represent entity as inactive (which is only part of the steps
needed for the deactivation of the entity).
2) The function must be invoked on every entity being deactivated.
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 5f0ed774ed ("block: sum requests in the plug structure") removed
the request_count parameter from block_attempt_plug_merge(), but did not
remove the associated kerneldoc comment, introducing this warning to the
docs build:
./block/blk-core.c:685: warning: Excess function parameter 'request_count' description in 'blk_attempt_plug_merge'
Remove the obsolete description and make things a little quieter.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There was some confusion about what these functions did. Make it clear
that this is a hint for upper layers to pass to the block layer, and
that it does not guarantee that I/O will not be submitted between a
start and finish plug.
Reported-by: "Darrick J. Wong" <darrick.wong@oracle.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
-----BEGIN PGP SIGNATURE-----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=KYFj
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20190102' of git://git.kernel.dk/linux-block
Pull more block updates from Jens Axboe:
- Dead code removal for loop/sunvdc (Chengguang)
- Mark BIDI support for bsg as deprecated, logging a single dmesg
warning if anyone is actually using it (Christoph)
- blkcg cleanup, killing a dead function and making the tryget_closest
variant easier to read (Dennis)
- Floppy fixes, one fixing a regression in swim3 (Finn)
- lightnvm use-after-free fix (Gustavo)
- gdrom leak fix (Wenwen)
- a set of drbd updates (Lars, Luc, Nathan, Roland)
* tag 'for-4.21/block-20190102' of git://git.kernel.dk/linux-block: (28 commits)
block/swim3: Fix regression on PowerBook G3
block/swim3: Fix -EBUSY error when re-opening device after unmount
block/swim3: Remove dead return statement
block/amiflop: Don't log error message on invalid ioctl
gdrom: fix a memory leak bug
lightnvm: pblk: fix use-after-free bug
block: sunvdc: remove redundant code
block: loop: remove redundant code
bsg: deprecate BIDI support in bsg
blkcg: remove unused __blkg_release_rcu()
blkcg: clean up blkg_tryget_closest()
drbd: Change drbd_request_detach_interruptible's return type to int
drbd: Avoid Clang warning about pointless switch statment
drbd: introduce P_ZEROES (REQ_OP_WRITE_ZEROES on the "wire")
drbd: skip spurious timeout (ping-timeo) when failing promote
drbd: don't retry connection if peers do not agree on "authentication" settings
drbd: fix print_st_err()'s prototype to match the definition
drbd: avoid spurious self-outdating with concurrent disconnect / down
drbd: do not block when adjusting "disk-options" while IO is frozen
drbd: fix comment typos
...
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=r3Fl
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig updates from Masahiro Yamada:
- support -y option for merge_config.sh to avoid downgrading =y to =m
- remove S_OTHER symbol type, and touch include/config/*.h files correctly
- fix file name and line number in lexer warnings
- fix memory leak when EOF is encountered in quotation
- resolve all shift/reduce conflicts of the parser
- warn no new line at end of file
- make 'source' statement more strict to take only string literal
- rewrite the lexer and remove the keyword lookup table
- convert to SPDX License Identifier
- compile C files independently instead of including them from zconf.y
- fix various warnings of gconfig
- misc cleanups
* tag 'kconfig-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (39 commits)
kconfig: surround dbg_sym_flags with #ifdef DEBUG to fix gconf warning
kconfig: split images.c out of qconf.cc/gconf.c to fix gconf warnings
kconfig: add static qualifiers to fix gconf warnings
kconfig: split the lexer out of zconf.y
kconfig: split some C files out of zconf.y
kconfig: convert to SPDX License Identifier
kconfig: remove keyword lookup table entirely
kconfig: update current_pos in the second lexer
kconfig: switch to ASSIGN_VAL state in the second lexer
kconfig: stop associating kconf_id with yylval
kconfig: refactor end token rules
kconfig: stop supporting '.' and '/' in unquoted words
treewide: surround Kconfig file paths with double quotes
microblaze: surround string default in Kconfig with double quotes
kconfig: use T_WORD instead of T_VARIABLE for variables
kconfig: use specific tokens instead of T_ASSIGN for assignments
kconfig: refactor scanning and parsing "option" properties
kconfig: use distinct tokens for type and default properties
kconfig: remove redundant token defines
kconfig: rename depends_list to comment_option_list
...
This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas. Additionally, we have
a pile of annotation, unused variable and minor updates. The big API
change is the updates for Christoph's DMA rework which include
removing the DISABLE_CLUSTERING flag. And finally there are a couple
of target tree updates.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXCEUNiYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishdjKAP9vrTTv
qFaYmAoRSbPq9ZiixaXLMy0K/6o76Uay0gnBqgD/fgn3jg/KQ6alNaCjmfeV3wAj
u1j3H7tha9j1it+4pUw=
=GDa+
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: smarpqi, lpfc, qedi,
megaraid_sas, libsas, zfcp, mpt3sas, hisi_sas.
Additionally, we have a pile of annotation, unused variable and minor
updates.
The big API change is the updates for Christoph's DMA rework which
include removing the DISABLE_CLUSTERING flag.
And finally there are a couple of target tree updates"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (259 commits)
scsi: isci: request: mark expected switch fall-through
scsi: isci: remote_node_context: mark expected switch fall-throughs
scsi: isci: remote_device: Mark expected switch fall-throughs
scsi: isci: phy: Mark expected switch fall-through
scsi: iscsi: Capture iscsi debug messages using tracepoints
scsi: myrb: Mark expected switch fall-throughs
scsi: megaraid: fix out-of-bound array accesses
scsi: mpt3sas: mpt3sas_scsih: Mark expected switch fall-through
scsi: fcoe: remove set but not used variable 'port'
scsi: smartpqi: call pqi_free_interrupts() in pqi_shutdown()
scsi: smartpqi: fix build warnings
scsi: smartpqi: update driver version
scsi: smartpqi: add ofa support
scsi: smartpqi: increase fw status register read timeout
scsi: smartpqi: bump driver version
scsi: smartpqi: add smp_utils support
scsi: smartpqi: correct lun reset issues
scsi: smartpqi: correct volume status
scsi: smartpqi: do not offline disks for transient did no connect conditions
scsi: smartpqi: allow for larger raid maps
...
-----BEGIN PGP SIGNATURE-----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=TRdW
-----END PGP SIGNATURE-----
Merge tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block
Pull block updates from Jens Axboe:
"This is the main pull request for block/storage for 4.21.
Larger than usual, it was a busy round with lots of goodies queued up.
Most notable is the removal of the old IO stack, which has been a long
time coming. No new features for a while, everything coming in this
week has all been fixes for things that were previously merged.
This contains:
- Use atomic counters instead of semaphores for mtip32xx (Arnd)
- Cleanup of the mtip32xx request setup (Christoph)
- Fix for circular locking dependency in loop (Jan, Tetsuo)
- bcache (Coly, Guoju, Shenghui)
* Optimizations for writeback caching
* Various fixes and improvements
- nvme (Chaitanya, Christoph, Sagi, Jay, me, Keith)
* host and target support for NVMe over TCP
* Error log page support
* Support for separate read/write/poll queues
* Much improved polling
* discard OOM fallback
* Tracepoint improvements
- lightnvm (Hans, Hua, Igor, Matias, Javier)
* Igor added packed metadata to pblk. Now drives without metadata
per LBA can be used as well.
* Fix from Geert on uninitialized value on chunk metadata reads.
* Fixes from Hans and Javier to pblk recovery and write path.
* Fix from Hua Su to fix a race condition in the pblk recovery
code.
* Scan optimization added to pblk recovery from Zhoujie.
* Small geometry cleanup from me.
- Conversion of the last few drivers that used the legacy path to
blk-mq (me)
- Removal of legacy IO path in SCSI (me, Christoph)
- Removal of legacy IO stack and schedulers (me)
- Support for much better polling, now without interrupts at all.
blk-mq adds support for multiple queue maps, which enables us to
have a map per type. This in turn enables nvme to have separate
completion queues for polling, which can then be interrupt-less.
Also means we're ready for async polled IO, which is hopefully
coming in the next release.
- Killing of (now) unused block exports (Christoph)
- Unification of the blk-rq-qos and blk-wbt wait handling (Josef)
- Support for zoned testing with null_blk (Masato)
- sx8 conversion to per-host tag sets (Christoph)
- IO priority improvements (Damien)
- mq-deadline zoned fix (Damien)
- Ref count blkcg series (Dennis)
- Lots of blk-mq improvements and speedups (me)
- sbitmap scalability improvements (me)
- Make core inflight IO accounting per-cpu (Mikulas)
- Export timeout setting in sysfs (Weiping)
- Cleanup the direct issue path (Jianchao)
- Export blk-wbt internals in block debugfs for easier debugging
(Ming)
- Lots of other fixes and improvements"
* tag 'for-4.21/block-20181221' of git://git.kernel.dk/linux-block: (364 commits)
kyber: use sbitmap add_wait_queue/list_del wait helpers
sbitmap: add helpers for add/del wait queue handling
block: save irq state in blkg_lookup_create()
dm: don't reuse bio for flushes
nvme-pci: trace SQ status on completions
nvme-rdma: implement polling queue map
nvme-fabrics: allow user to pass in nr_poll_queues
nvme-fabrics: allow nvmf_connect_io_queue to poll
nvme-core: optionally poll sync commands
block: make request_to_qc_t public
nvme-tcp: fix spelling mistake "attepmpt" -> "attempt"
nvme-tcp: fix endianess annotations
nvmet-tcp: fix endianess annotations
nvme-pci: refactor nvme_poll_irqdisable to make sparse happy
nvme-pci: only set nr_maps to 2 if poll queues are supported
nvmet: use a macro for default error location
nvmet: fix comparison of a u16 with -1
blk-mq: enable IO poll if .nr_queues of type poll > 0
blk-mq: change blk_mq_queue_busy() to blk_mq_queue_inflight()
blk-mq: skip zero-queue maps in blk_mq_map_swqueue
...
Besides the OSD command set that never got traction, the only SCSI
command using bidirectional buffers is XDWRITEREAD in the 10 and 32 byte
variants, which is extremely esoteric and has been removed from the spec
again as of SBC4r15. It probably doesn't make sense to keep the support
code around just for that, so start deprecating the support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
An earlier commit 7fcf2b033b ("blkcg: change blkg reference counting
to use percpu_ref") moved around the release call from blkg_put() to be
a part of the percpu_ref cleanup. Remove the additional unused code
which should have been removed earlier.
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The implementation of blkg_tryget_closest() wasn't super obvious and
became a point of suspicion when debugging [1]. So let's clean it up so
it's obviously not the problem.
Also add missing RCU read locking to bio_clone_blkg_association(), which
got exposed by adding the RCU read lock held check in
blkg_tryget_closest().
[1] https://lore.kernel.org/linux-block/a7e97e4b-0dd8-3a54-23b7-a0f27b17fde8@kernel.dk/
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The Kconfig lexer supports special characters such as '.' and '/' in
the parameter context. In my understanding, the reason is just to
support bare file paths in the source statement.
I do not see a good reason to complicate Kconfig for the room of
ambiguity.
The majority of code already surrounds file paths with double quotes,
and it makes sense since file paths are constant string literals.
Make it treewide consistent now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
sbq_wake_ptr() checks sbq->ws_active to know if it needs to loop
the wait indexes or not. This requires the use of the sbitmap
waitqueue wrappers, but kyber doesn't use those for its domain
token waitqueue handling.
Convert kyber to use the helpers. This fixes a hang with waiting
for domain tokens.
Fixes: 5d2ee7122c ("sbitmap: optimize wakeup check")
Tested-by: Ming Lei <ming.lei@redhat.com>
Reported-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that the the SCSI layer replaced the use of the cluster flag with
segment size limits and the DMA boundary we can remove the cluster flag
from the block layer.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
block consumers will need it for polling requests that
are sent with blk_execute_rq_nowait. Also, get rid of
blk_tag_to_qc_t and open-code it instead.
Reviewed-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The queue mapping of type poll only exists when set->map[HCTX_TYPE_POLL].nr_queues
is bigger than zero, so enhance the constraint by checking .nr_queues of type poll
before enabling IO poll.
Otherwise IO race & timeout can be observed when running block/007.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There's a single user of this function, dm, and dm just wants
to check if IO is inflight, not that it's just allocated.
This fixes a hang with srp/002 in blktests with dm, where it tries
to suspend but waits for inflight IO to finish first. As it checks
for just allocated requests, this fails.
Tested-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
From 7e849dd9cf ("nvme-pci: don't share queue maps"), the mapping
table won't be initialized actually if map->nr_queues is zero, so
we can't use blk_mq_map_queue_type() to retrieve hctx any more.
This way still may cause broken mapping, fix it by skipping zero-queues
maps in blk_mq_map_swqueue().
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The blk-iolatency controller measures the time from rq_qos_throttle() to
rq_qos_done_bio() and attributes this time to the first bio that needs
to create the request. This means if a bio is plug-mergeable or
bio-mergeable, it gets to bypass the blk-iolatency controller.
The recent series [1], to tag all bios w/ blkgs undermined how iolatency
was determining which bios it was charging and should process in
rq_qos_done_bio(). Because all bios are being tagged, this caused the
atomic_t for the struct rq_wait inflight count to underflow and result
in a stall.
This patch adds a new flag BIO_TRACKED to let controllers know that a
bio is going through the rq_qos path. blk-iolatency now checks if this
flag is set to see if it should process the bio in rq_qos_done_bio().
Overloading BLK_QUEUE_ENTERED works, but makes the flag rules confusing.
BIO_THROTTLED was another candidate, but the flag is set for all bios
that have gone through blk-throttle code. Overloading a flag comes with
the burden of making sure that when either implementation changes, a
change in setting rules for one doesn't cause a bug in the other. So
here, we unfortunately opt for adding a new flag.
[1] https://lore.kernel.org/lkml/20181205171039.73066-1-dennis@kernel.org/
Fixes: 5cdf2e3fea ("blkcg: associate blkg when associating a device")
Signed-off-by: Dennis Zhou <dennis@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a request is added to rq list of sw queue(ctx), the rq may be from
a different type of hctx, especially after multi queue mapping is
introduced.
So when dispach request from sw queue via blk_mq_flush_busy_ctxs() or
blk_mq_dequeue_from_ctx(), one request belonging to other queue type of
hctx can be dispatched to current hctx in case that read queue or poll
queue is enabled.
This patch fixes this issue by introducing per-queue-type list.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Changed by me to not use separately cacheline aligned lists, just
place them all in the same cacheline where we had just the one list
and lock before.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
For a zoned block device using mq-deadline, if a write request for a
zone is received while another write was already dispatched for the same
zone, dd_dispatch_request() will return NULL and the newly inserted
write request is kept in the scheduler queue waiting for the ongoing
zone write to complete. With this behavior, when no other request has
been dispatched, rq_list in blk_mq_sched_dispatch_requests() is empty
and blk_mq_sched_mark_restart_hctx() not called. This in turn leads to
__blk_mq_free_request() call of blk_mq_sched_restart() to not run the
queue when the already dispatched write request completes. The newly
dispatched request stays stuck in the scheduler queue until eventually
another request is submitted.
This problem does not affect SCSI disk as the SCSI stack handles queue
restart on request completion. However, this problem is can be triggered
the nullblk driver with zoned mode enabled.
Fix this by always requesting a queue restart in dd_dispatch_request()
if no request was dispatched while WRITE requests are queued.
Fixes: 5700f69178 ("mq-deadline: Introduce zone locking support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Add missing export of blk_mq_sched_restart()
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We should check if a given queue map actually has queues enabled before
dispatching to it. This allows drivers to not initialize optional but
not used map types, which subsequently will allow fixing problems with
queue map rebuilds for that case.
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now we only export hctx->type via sysfs, and there isn't such info
in hctx entry under debugfs. We often use debugfs only to diagnose
queue mapping issue, so add the support in debugfs.
Queue mapping becomes a bit more complicated after multiple queue
mapping is supported, we may write blktest to verify if queue mapping
is valid based on blk-mq-debugfs.
Given not necessary to export hctx->type twice, so remove the export
from sysfs.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Type of each element in queue mapping table is 'unsigned int,
intead of 'struct blk_mq_queue_map)', so fix it.
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
