Add support for the RTC's NVRAM using the standard nvmem support that is
part of the Linux RTC framework.
This driver already has a sysfs attribute that provides access to the
RTC's NVRAM as a single 16-bit value. Some chips have more than two
bytes of NVRAM, so this will not work for them. It's also non-standard.
This sysfs attribute is left in for backward compatibility, but will only
be able to read the first two bytes of NVRAM. The nvmem interface will
allow access to all NVRAM, e.g. eight bytes on the isl1218.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add more support in the driver for dealing with differences in is1208
compatible chips. Put the 1208, 1209, 1218, and 1219 in the list and
encode information about nvram size, tamper, and timestamp features.
This adds support for the isl1209, which has a tamper detect but no
timestamp feature.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This driver has no state of its own, depending entirely on what is in
the generic rtc device.
Intoduce a state struct. For now it only contains a pointer to the rtc
device struct, but future patches will add more data.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
rtc_nvmem_unregister() is called on rtc_device release so it is not
necessary to call it from the driver.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for the RTC block on the 32-bit Amlogic Meson6, Meson8,
Meson8b and Meson8m2 SoCs.
The RTC is split in to two parts, which are both managed by this driver:
- the AHB front end
- and a simple serial connection to the actual registers
The RTC_COUNTER register which holds the time is 32-bits wide.
There are four 32-bit wide (in total: 16 bytes) "regmem" registers which
are exposed using nvmem. On Amlogic's 3.10 kernel this is used to store
data which needs to survive a suspend / resume cycle.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
[resurrected Ben's patches after 2 years]
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When the oscillator of the rtc gets interrupted,
e.g. due to an empty battery, reading from the rtc will now return an error
and the oscillator bit will be cleared, once the rtc is successfully reset.
Signed-off-by: Oliver Rohe <oliver.rohe@wago.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fix the following build issue:
drivers/rtc/rtc-imx-sc.o: In function `imx_sc_rtc_set_time':
>> rtc-imx-sc.c:(.text+0x212): undefined reference to `__arm_smccc_smc'
Fixes: 13a929f38a ("rtc: imx-sc: add rtc set time support")
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#1309693 ("Unintended sign extension")
Fixes: 9a9a54ad7a ("drivers/rtc: add support for Qualcomm PMIC8xxx RTC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#714646-714649 ("Unintended sign extension")
Fixes: 2985c29c19 ("rtc: Add rtc support to 88PM80X PMIC")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#144925-144928 ("Unintended sign extension")
Fixes: 008b30408c ("mfd: Add rtc support to 88pm860x")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When the EXTENSION.WADA bit is set, register 0x19 contains a bitmap of
week days, not a day of month. As Linux only handles a single alarm
without repetition using day of month is more flexible, so clear this
bit. (Otherwise a value depending on time.tm_wday would have to be
written to register 0x19.)
Also optimize setting the AIE bit to use a single register write instead
of a bulk write of three registers.
Fixes: ee0981be77 ("rtc: ds1307: Add support for Epson RX8130CE")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When voltage dropped since the RTC was last set the reported time is not
reliable. In this case return an error indicator instead of a bogus
time.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
While rx8130 has a register offset of 0x10 in its chip_desc, this isn't
used when regmap accesses are done. So add 0x10 to access the right
locations.
Fixes: ee0981be77 ("rtc: ds1307: Add support for Epson RX8130CE")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
There used to be 16 declarations for static functions. By just adding a
declaration for the chips array and reordering the functions the 16
function declarations can be dropped.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This allows to use the register offsets in all functions
which is needed in one of the next patches.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch adds i.MX system controller RTC set time support, the
RTC set time is implemented via SIP(silicon provider) runtime
service call and ARM-Trusted-Firmware will communicate with system
controller via MU(message unit) IPC to set RTC time.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Ricoh chips have slightly different register layouts
and the r2221 chip uses bit 5 as the oscillator halt sensor bit.
Signed-off-by: Olive Rohe <oliver.rohe@wago.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
During system suspend, the SNVS RTC's clock will be disabled in
noirq suspend phase, but SNVS RTC's alarm interrupt could still
arrive, system will hang if SNVS RTC driver tries to access register
without clock enabled, this patch fixes the issue of this scenario.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Shifting a u8 by 24 will cause the value to be promoted to an integer. If
the top bit of the u8 is set then the following conversion to an unsigned
long will sign extend the value causing the upper 32 bits to be set in
the result.
Fix this by casting the u8 value to an unsigned long before the shift.
Detected by CoverityScan, CID#138801 ("Unintended sign extension")
Fixes: edf1aaa31f ("[PATCH] RTC subsystem: DS1672 driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RV1805 uses smaller package than the AB1805, discern those two
chips based on the compatible value and configure reserved bits in
the RV1805 to prevent current leakage and accidental test mode entry.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
To: linux-rtc@vger.kernel.org
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This patch adds a driver for Cadence RTC controller.
It can be enabled with RTC_DRV_CADENCE Kconfig option.
It supports waking system from sleep modes.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Older versions of Libreboot and Coreboot had an invalid value
(`3' in my case) in the century byte affecting the GM45 in
the Thinkpad X200. Not everybody's updated their firmwares,
and Linux <= 4.2 was able to read the RTC without problems,
so workaround this by ignoring invalid values.
Fixes: 3c217e51d8 ("rtc: cmos: century support")
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Sylvain Chouleur <sylvain.chouleur@intel.com>
Cc: Patrick McDermott <patrick.mcdermott@libiquity.com>
Cc: linux-rtc@vger.kernel.org
Signed-off-by: Eric Wong <e@80x24.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
When i2c_smbus_read_i2c_block_data() fails, the read data in "buf" could
be incorrect and should not be used. The fix checks if
i2c_smbus_read_i2c_block_data fails, and if so, return its error code
upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
clk_prepare() could fail, so let's check its status and if it fails
return its error code upstream.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for specifying the xtal load capacitance in the DT node.
The pcf85063 supports xtal load capacitance of 7pF or 12.5pF.
If the rtc has the wrong configuration the time will
drift several hours/week.
The driver use the default value 7pF.
The DT may specify either 7000fF or 12500fF.
(The DT uses femto Farad to avoid decimal numbers).
Other values are warned and the driver uses the default value.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Urs Fässler <urs.fassler@bbv.ch>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for specifying the xtal load capacitance in the DT node.
The pcf8523 supports xtal load capacitance of 7pF or 12.5pF.
If the rtc has the wrong configuration the time will
drift several hours/week.
The driver use the default value 12.5pF.
The DT may specify either 7000fF or 12500fF.
(The DT uses femto Farad to avoid decimal numbers).
Other values are warned and the driver uses the default value.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Replace of_match_node() with of_device_get_match_data(), which removes a
few lines of code from the driver.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
s3c_rtc_enable/disable_clk() functions were designed to be called multiple
times without reference counting, because they were initially only used in
alarm setting/clearing functions, which can be called both when alarm is
already set or not. Later however, calls to those functions have been added to
other places in the driver - like time and /proc reading callbacks, what
results in broken alarm if any of such events happens after the alarm has
been set. Fix this by simplifying s3c_rtc_enable/disable_clk() functions
to rely on proper reference counting in clock core and move alarm enable
counter to s3c_rtc_setaie() function.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes the following sparse warning:
drivers/rtc/rtc-sd3078.c:218:19: warning:
symbol 'sd3078_driver' was not declared. Should it be static?
Fixes: 1d67a23210 ("rtc: sd3078: new driver.")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
isl1208_i2c_get_dtr() was returning the dtr value directly, but could
also return a negative error code. Negative trimming values, e.g. -20,
would get interpreted as an error code, e.g. -ENOTDIR.
This patch offsets the dtr value by 100 so it's positive and won't alias
an error code.
Also fix check that considered a return value of -1 to be success.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Users may call 'ioctl' and pass a very big value on 'tm->tm_year'.
It can be overflowed in 'int' after add 1900.
In function 'rtc_month_days' and 'mktime64', also treated it as an
'unsigned' parameter.
UBSAN: Undefined behaviour in drivers/rtc/rtc-lib.c:103:59
signed integer overflow:
2147483647 + 1900 cannot be represented in type 'int'
UBSAN: Undefined behaviour in drivers/rtc/rtc-lib.c:119:30
signed integer overflow:
2147483647 + 1900 cannot be represented in type 'int'
So, covert it to 'unsigned' explicitly.
Signed-off-by: ZhangXiaoxu <zhangxiaoxu5@huawei.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The sd3078 is a combination RTC and SRAM device with I2C interface.
Signed-off-by: Dianlong Li <long17.cool@163.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Drivers:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding
-----BEGIN PGP SIGNATURE-----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=5He5
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- new %ptR printk format
- rename core files
- allow registration of multiple nvmem devices
New driver:
- i.MX system controller RTC
Driver updates:
- abx80x: handle voltage ioctls, correct binding doc
- m41t80: correct month in alarm reads
- pcf85363: add pcf85263 support
- pcf8523: properly handle battery low flag
- s3c: limit alarm to one year in the future as ALMYEAR is broken
- sun6i: rework clock output binding"
* tag 'rtc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (54 commits)
rtc: rename core files
rtc: nvmem: fix possible use after free
rtc: add i.MX system controller RTC support
dt-bindings: fsl: scu: add rtc binding
rtc: pcf2123: Add Microcrystal rv2123
rtc: class: reimplement devm_rtc_device_register
rtc: enforce rtc_timer_init private_data type
rtc: abx80x: Implement RTC_VL_READ,CLR ioctls
rtc: pcf85363: Add support for NXP pcf85263 rtc
dt-bindings: rtc: pcf85363: Document pcf85263 real-time clock
rtc: pcf8523: don't return invalid date when battery is low
dt-bindings: rtc: use a generic node name for ds1307
PM: Switch to use %ptR
m68k/mac: Switch to use %ptR
Input: hp_sdc_rtc - Switch to use %ptR
rtc: tegra: Switch to use %ptR
rtc: s5m: Switch to use %ptR
rtc: s3c: Switch to use %ptR
rtc: rx8025: Switch to use %ptR
rtc: rx6110: Switch to use %ptR
...
Rename core files so there is a clearer separation between the RTC core and
the RTC drivers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
In cas of probe failure, devres may free the memory allocated for
rtc->nvram before devm_rtc_release_device() is called. This leads to
rtc_nvram_unregister using it after being freed which may lead to a crash.
This has been shown to happen after commit 461e557b97 ("rtc: nvmem: use
devm_nvmem_register()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
i.MX8QXP is an ARMv8 SoC which has a Cortex-M4 system controller
inside, the system controller is in charge of controlling power,
clock and secure rtc etc..
This patch adds i.MX system controller RTC driver support,
Linux kernel has to communicate with system controller via MU
(message unit) IPC to set/get RTC time and other alarm functions,
since the RTC set time needs to be done in secure EL3 mode (required
by system controller firmware) and alarm functions needs to be done
with general MU IRQ handle, these depend on other components which
are NOT ready, so this patch ONLY enables the RTC time read.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add a compatible string for Microcrystal rv2123 as the reset procedure seem
to be differing. However, the current driver works just fine.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Implement devm_rtc_device_register using devm_rtc_allocate_device and
__rtc_register_device so there is only one path left to register rtc
devices.
Also mark it as deprecated so new drivers will hopefully use
devm_rtc_allocate_device and rtc_register_device that are less race prone
and allow avoiding the 2038, 2070, 2100 and 2106 bugs properly.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
All the remaining users of rtc_timers are passing the rtc_device as private
data. Enforce that and rename private_data to rtc.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Implement standard ioctls for polling the battery status and clearing
the battery low indication from userspace.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add support for NXP pcf85263 real-time clock. pcf85263 rtc is compatible
with pcf85363,except that pcf85363 has additional 64 bytes of RAM.
1 byte of nvmem is supported and exposed in sysfs (# is the instance
number,starting with 0): /sys/bus/nvmem/devices/pcf85x63-#/nvmem
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The RTC_VL_READ ioctl reports the low battery condition. Still,
pcf8523_rtc_read_time() happily returns invalid dates in this case.
Check the battery health on pcf8523_rtc_read_time() to avoid that.
Reported-by: Erik Čuk <erik.cuk@domel.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use %ptR instead of open coded variant to print content of
struct rtc_time in human readable format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
