Change the register map names to reflect the IP revision they
are representing, and use the platform_data IP revision index
to select between them at init time.
Eliminates 1 of 17 cpu_...() calls in the driver.
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The OMAP I2C driver dynamically chooses between two register sets of
differing sizes depending on the cpu type it finds itself on.
It has been observed that the existing code references non-existing
registers on OMAP3530, because while it correctly chose the smaller
register layout based on cpu type, the code uses the probed register
ID to decide if to execute code referencing an extra register, and
both register layout devices on OMAP3530 and OMAP4430 report the same
probed ID of 0x40.
This patch changes the extended register names only found on IP V2
of the I2C peripheral unit accordingly to help show up errors in usage.
Cc: patches@linaro.org
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* 'for-linus' of git://ceph.newdream.net/git/ceph-client:
libceph: fix double-free of page vector
ceph: fix 32-bit ino numbers
libceph: force resend of osd requests if we skip an osdmap
ceph: use kernel DNS resolver
ceph: fix ceph_monc_init memory leak
ceph: let the set_layout ioctl set single traits
Revert "ceph: don't truncate dirty pages in invalidate work thread"
ceph: replace leading spaces with tabs
libceph: warn on msg allocation failures
libceph: don't complain on msgpool alloc failures
libceph: always preallocate mon connection
libceph: create messenger with client
ceph: document ioctls
ceph: implement (optional) max read size
ceph: rename rsize -> rasize
ceph: make readpages fully async
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
* 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Clean-up MPS debug output
pci: Clamp pcie_set_readrq() when using "performance" settings
PCI: enable MPS "performance" setting to properly handle bridge MPS
PCI: Workaround for Intel MPS errata
PCI: Add support for PASID capability
PCI: Add implementation for PRI capability
PCI: Export ATS functions to modules
PCI: Move ATS implementation into own file
PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()
PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove
PCI / PM: Extend PME polling to all PCI devices
PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823
PCI: Make pci_setup_bridge() non-static for use by arch code
x86: constify PCI raw ops structures
PCI: Add quirk for known incorrect MPSS
PCI: Add Solarflare vendor ID and SFC4000 device IDs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits)
mmc: fix compile error when CONFIG_BLOCK is not enabled
mmc: core: Cleanup eMMC4.5 conditionals
mmc: omap_hsmmc: if multiblock reads are broken, disable them
mmc: core: add workaround for controllers with broken multiblock reads
mmc: core: Prevent too long response times for suspend
mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
mmc: core: support HPI send command
mmc: core: Add cache control for eMMC4.5 device
mmc: core: Modify the timeout value for writing power class
mmc: core: new discard feature support at eMMC v4.5
mmc: core: mmc sanitize feature support for v4.5
mmc: dw_mmc: modify DATA register offset
mmc: sdhci-pci: add flag for devices that can support runtime PM
mmc: omap_hsmmc: ensure pbias configuration is always done
mmc: core: Add Power Off Notify Feature eMMC 4.5
mmc: sdhci-s3c: fix potential NULL dereference
mmc: replace printk with appropriate display macro
mmc: core: Add default timeout value for CMD6
mmc: sdhci-pci: add runtime pm support
...
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the extended active speeds based on the hardware configuration.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Hal Rosenstock <hal@mellanox.com>
[ Move FDR-10 handling into ib_link_query_port(). - Roland ]
Signed-off-by: Roland Dreier <roland@purestorage.com>
An Extended Port Info packet is sent to each hw port during HCA init.
If it returns without error, we assume the port supports extended port
capabilities.
Signed-off-by: Marcel Apfelbaum <marcela@dev.mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
* 'drm-core-next' of git://people.freedesktop.org/~airlied/linux: (290 commits)
Revert "drm/ttm: add a way to bo_wait for either the last read or last write"
Revert "drm/radeon/kms: add a new gem_wait ioctl with read/write flags"
vmwgfx: Don't pass unused arguments to do_dirty functions
vmwgfx: Emulate depth 32 framebuffers
drm/radeon: Lower the severity of the radeon lockup messages.
drm/i915/dp: Fix eDP on PCH DP on CPT/PPT
drm/i915/dp: Introduce is_cpu_edp()
drm/i915: use correct SPD type value
drm/i915: fix ILK+ infoframe support
drm/i915: add DP test request handling
drm/i915: read full receiver capability field during DP hot plug
drm/i915/dp: Remove eDP special cases from bandwidth checks
drm/i915/dp: Fix the math in intel_dp_link_required
drm/i915/panel: Always record the backlight level again (but cleverly)
i915: Move i915_read/write out of line
drm/i915: remove transcoder PLL mashing from mode_set per specs
drm/i915: if transcoder disable fails, say which
drm/i915: set watermarks for third pipe on IVB
drm/i915: export a CPT mode set verification function
drm/i915: fix transcoder PLL select masking
...
* 'x86-rdrand-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, random: Verify RDRAND functionality and allow it to be disabled
x86, random: Architectural inlines to get random integers with RDRAND
random: Add support for architectural random hooks
Fix up trivial conflicts in drivers/char/random.c: the architectural
random hooks touched "get_random_int()" that was simplified to use MD5
and not do the keyptr thing any more (see commit 6e5714eaf7: "net:
Compute protocol sequence numbers and fragment IDs using MD5").
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Add microcode revision to /proc/cpuinfo
x86, microcode: Correct microcode revision format
coretemp: Get microcode revision from cpu_data
x86, intel: Use c->microcode for Atom errata check
x86, intel: Output microcode revision in /proc/cpuinfo
x86, microcode: Don't request microcode from userspace unnecessarily
Fix up trivial conflicts in arch/x86/kernel/cpu/amd.c (conflict between
moving AMD BSP code to cpu_dev helper function and adding AMD microcode
revision to /proc/cpuinfo code)
* 'x86-hyperv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Hyper-V: Integrate the clocksource with Hyper-V detection code
Fix up conflicts in drivers/staging/hv/Makefile manually (some of the hv
code has moved out of staging to drivers/hv/)
This patch updates the normal descriptor structure
to work fine on new GMAC Synopsys chips.
Normal descriptors were designed on the old MAC10/100
databook 1.91 where some bits were reserved: for example
the tx checksum insertion and rx checksum offload.
The patch maintains the back-compatibility with old
MAC devices (tested on STx7109 MAC10/100) and adds new
fields that actually new GMAC devices can use.
For example, STx7109 (MAC10/100) will pass from the platform
tx_coe = 0, enh_desc = 0, has_gmac = 0.
A platform like Loongson1B (GMAC) will pass:
tx_coe = 1, enh_desc = 0, has_gmac = 1.
Thanks to Kelvin, he enhanced the normal descriptors for
GMAC (on MIPS Loongson1B platform).
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Angus Clark <angus.clark@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes a bug while checking the HW cap reg
on old MAC10/100 where this feature is not available.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow for MAC Address change of VF(SR-IOV case) on the fly- First add and then
delete MAC Address to allow for 'out of pool' errors.
When MAC Addr configured from a VM, the MAC on the NIC will aleady have
the supplied MAC,so just copy the supplied MAC to the netdev structure
before returning success to the stack
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moved the .sge. field's population inside be_cmd_hdr_prepare.
Populating wrb->tag0 and tag1 inside be_cmd_hdr_prepare
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FW includes the following fixes:
1. (iSCSI) Arrival of un-solicited ASYNC message causes
firmware to abort the connection with RST.
2. (FCoE) There is a probability that truncated FCoE packet on
RX path won't get detected which might lead to FW assert.
3. (iSCSI) Arrival of target-initiated NOP-IN during intense
ISCSI traffic might lead to FW assert.
4. (iSCSI) Chip hangs when in case of retransmission not aligned
to 4-bytes from the beginning of iSCSI PDU.
5. (FCoE) Arrival of packets beyond task IO size can lead to crash.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem in which the host stops receiving data after
restarting the interface. This issue is caused by combination of incorrect
data path tap closure, along with missing MAC reset.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix solves a problem of no link on 578xx-KR by retrying to link up to
four timer using the periodic function.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust blink rate on 578xx to fit its clock rate.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean-up MPS debug output to make it a single line and aligned, thus
making it more readable for a large number of buses and devices in a
single system.
Suggested by Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
When configuring the PCIe settings for "performance", we allow parents
to have a larger Max Payload Size than children and rely on children
Max Read Request Size to not be larger than their own MPS to avoid
having the host bridge generate responses they can't cope with.
However, various drivers in Linux call pci_set_readrq() with arbitrary
values, assuming this to be a simple performance tweak. This breaks
under our "performance" configuration.
Fix that by making sure the value programmed by pcie_set_readrq() is
never larger than the configured MPS for that device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jon Mason <mason@myri.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Rework the "performance" MPS option to configure the device MPS with the
smaller of the device MPSS or the bridge MPS (which is assumed to be
properly configured at this point to the largest allowable MPS based on
its parent bus).
Also, rework the MRRS setting to report an inability to set the MRRS to
a valid setting.
Signed-off-by: Jon Mason <mason@myri.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This reverts commit dfadbbdb57.
Further upstream discussion between Marek and Thomas decided this wasn't
fully baked and needed further work, so revert it before it hits mainline.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reverts commit d3ed74027f.
Further upstream discussion between Thomas and Marek decided this needed
more work and driver specifics. So revert before it goes upstream.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Code cleanup, putting all eMMC 4.5 detection cases together.
This patch removes one if-statement and assembles all. And it also
removes variable initialization below else-statement -- all members
of card structure are already set to zero at card-init.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
When device data indicates that multiple block reads are not supported
on a given HSMMC controller instance, log a message to the console, and
pass the appropriate MMC capability flag to the MMC core.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Due to hardware bugs, some MMC host controllers don't support
multiple-block reads[1]. To resolve, add a new MMC capability flag,
MMC_CAP2_NO_MULTI_READ, which can be set by affected host controller
drivers. When this capability is set, all reads will be issued one
sector at a time.
1. See for example Advisory 2.1.1.128 "MMC: Multiple Block Read
Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
Revision F (October 2010) (SPRZ278F), available from
http://focus.ti.com/lit/er/sprz278f/sprz278f.pdf
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Dave Hylands <dhylands@gmail.com>
Tested-by: Steve Sakoman <sakoman@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (68 commits)
Input: adp5589-keys - add support for the ADP5585 derivatives
Input: imx_keypad - add pm suspend and resume support
Input: force feedback - potential integer wrap in input_ff_create()
Input: tsc2007 - make sure that X plate resistance is specified
Input: serio_raw - fix memory leak when closing char device
Input: serio_raw - kick clients when disconnecting port
Input: serio_raw - explicitly mark disconnected ports as dead
Input: serio_raw - fix coding style issues
Input: serio_raw - use dev_*() for messages
Input: serio_raw - use bool for boolean data
Input: serio_raw - perform proper locking when adding clients to list
Input: serio_raw - rename serio_raw_list to serio_raw_client
Input: serio_raw - use kref instead of rolling out its own refcounting
Input: psmouse - switch to using dev_*() for messages
Input: wacom - correct max Y value on medium bamboos
Input: wacom - add ABS_DISTANCE to Bamboo Pen reports
Input: wacom - remove unneeded touch pressure initialization
Input: lm8323 - wrap suspend and resume in CONFIG_PM_SLEEP
Input: ad7879-i2c - wrap suspend and resume in CONFIG_PM_SLEEP
Input: synaptics_i2c - wrap suspend and resume in CONFIG_PM_SLEEP
...
* 'clk' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7131/1: clkdev: Add Common Macro for clk_lookup
clk: spi-pl022: convert to clk_prepare()/clk_unprepare()
clk: timer-sp: convert to clk_prepare()/clk_unprepare()
clk: sa1111: convert to clk_prepare()/clk_unprepare()
clk: mmci: convert to clk_prepare()/clk_unprepare()
clk: amba-pl011: convert to clk_prepare()/clk_unprepare()
clk: amba-pl010: convert to clk_prepare()/clk_unprepare()
clk: amba-clcd: convert to clk_prepare()/clk_unprepare()
clk: amba bus: convert to clk_prepare()/clk_unprepare()
clk: provide prepare/unprepare functions
* 'upstream-linus' of git://github.com/jgarzik/libata-dev: (50 commits)
pata_efar: fix register naming used in efar_set_piomode()
pata_rdc: add Power Management support
ata_piix: unify code for programming PIO and MWDMA timings
ata_piix: SITRE handling fix
libata: make ata_sff_data_xfer_noirq() work with 32-bit PIO
pata_artop: add Power Management support
pata_sl82c105: add Power Management support
pata_pdc2027x: add Power Management support
pata_legacy: use PIO mask defines
pata_legacy: unify QDI ->set_piomode methods
libata: remove no longer needed pata_qdi driver
pata_it8213: fix register naming used in it8213_set_piomode()
pata_it8213: add UDMA100 and UDMA133 support
pata_rdc: parallel scanning needs an extra locking
pata_via: add via_fixup()
libata: ata_timing_compute() fixup
pata_scc: add proper cable detection method
pata_arasan_cf: remove bogus to_platform_device() calls
pata_atiixp: add proper ->prereset method
pata_serverworks: add serverworks_fixup()
...
run_guest tries to freeze the current process after it has handled
pending interrupts and before it calls lguest_arch_run_guest.
This doesn't work nicely if the task has been killed while being frozen
and when we want to handle that signal as soon as possible.
Let's move try_to_freeze before we check for pending signal so that we
can get out of the loop as soon as possible.
Signed-off-by: Michal Hocko <mhocko@suse.cz>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We actually can run under KVM, as it doesn't paravirtualize anything we
need to use; reduce the check to checking we are the normal ringlevel.
Reported-by: Stefanos Geraggelos <sgerag@cslab.ece.ntua.gr>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au># HG changeset patch
This adds devicetree binding support to the ARM pl061 driver removing the
platform_data dependency. When DT binding is used, the gpio numbering is
assigned dynamically. For now, interrupts are not supported with DT until
irqdomains learn dynamic irq assignment.
Rather than add another case of -1, updating the driver to use NO_IRQ.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
While trying to suspend the mmc host there could still be
ongoing requests that we need to wait for. At the same time
a device driver must respond to a suspend request rather quickly.
Instead of potentially wait "forever" by claiming the host we now
"try" to claim the host instead. If it fails, -EBUSY is returned.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Table 6-2: CCCR bit Definitions, address 00h. Part E1 SDIO Simplified
Specification Version 3.00, Feb. 25, 2011.
This patch has been tested with Marvell WLAN device SD8797.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Here is Essential conditions to indicate Version 3.00 Card
(SD_SPEC=2 and SD_SPEC3=1) :
(1) The card shall support CMD6
(2) The card shall support CMD8
(3) The card shall support CMD42
(4) User area capacity shall be up to 2GB (SDSC) or 32GB (SDHC)
User area capacity shall be more than or equal to 32GB and
up to 2TB (SDXC)
(5) Speed Class shall be supported (SDHC or SDXC)
So even if SD card doesn't support any of the newly defined
UHS-I bus speed mode, it can advertise itself as SD3.0 cards
as long as it supports all the essential conditions of
SD3.0 cards. Given this, these type of cards should atleast
run in High Speed mode @50MHZ if it supports HS.
But current initialization sequence for SD3.0 cards is
such that these non-UHS-I SD3.0 cards runs in Default
Speed mode @25MHz.
This patch makes sure that these non-UHS-I SD3.0 cards run
in High Speed Mode @50MHz.
Tested this patch with SanDisk Extreme SDHC 8GB Class 10 card.
Reported-by: "Hiremath, Vaibhav" <hvaibhav@ti.com>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
HPI command is defined in eMMC4.41.
This feature is important for eMMC4.5 devices.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds cache feature of eMMC4.5 Spec.
If device supports cache capability, host can utilize some specific
operations.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch will apply the generic CMD6 timeout to switch command
for power class.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC v4.5 supports the DISCARD feature (CMD38). It's different from
trim and there's no check bit. Currently it's only supported at v4.5.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the v4.5, there's no secure erase & trim support.
Instead it supports the sanitize feature.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In dw_mmc 2.40a spec, Data register's offset is changed.
Before we used Data register offset 0x100. but if somebody uses a
2.40a controller, we must use 0x200 for Data register.
This patch adds a version-id checking point and uses SDMMC_DATA(x)
instead of SDMMC_DATA. It assumes 2.40a is the latest version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Only allow runtime PM for devices that specifically indicate
that they support it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Go through the driver's set_power() functions rather than
calling regulator_enable/disable() directly because otherwise
pbias configuration for MMC1 is not done.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for the power off notify feature, available in
eMMC 4.5 devices. If the host has support for this feature, then the
mmc core will notify the device by setting the POWER_OFF_NOTIFICATION
byte in the extended csd register with a value of 1 (POWER_ON).
For suspend mode short timeout is used, whereas for the normal poweroff
long timeout is used.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
sc->clk_bus[ptr] could be NULL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
All the files using printk function for displaying kernel messages
in the mmc driver have been replaced with corresponding macro.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
EXT_CSD[248] includes the default maximum timeout for CMD6.
This field is added at eMMC4.5 Spec. And it can be used for default
timeout except for some operations which don't define the timeout
(i.e. background operation, sanitize, flush cache) in eMMC4.5 Spec.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Ths patch allows runtime PM for sdhci-pci, runtime suspending after
inactivity of 50ms and ensuring runtime resume before SDHC registers
are accessed. During runtime suspend, interrupts are masked.
The host controller state is restored at runtime resume.
For Medfield, the host controller's card detect mechanism is
supplanted by an always-on GPIO which provides for card detect wake-up.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_request_done() is sometimes called from interrupt or other atomic
context. Mostly all mmc_request_done() does is complete(), however it
contains code to retry on error, which uses ->request(). As the error
path is certainly not performance critical, this may be moved to the
waiting function mmc_wait_for_req_done().
This allows ->request() to use runtime PM get_sync() and guarantee it
is never in an atomic context.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We are cleaning up the implicit presence of module.h; these guys are
some of the people who just assume it will be there. Call it out
explitly for those that really need it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Commit "mmc: add module param to set fault injection attributes" adds
a module_param to this file. But it is relying on the old implicit
"module.h is everywhere" behaviour, and without the explicit include
of moduleparam.h, the pending module.h split up produces this error:
core/debugfs.c:28:35: error: expected ')' before numeric constant
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
It allows gerneral purpose partitions in MMC Device. And I try to simply
make mmc_blk_alloc_parts using mmc_part structure suggested by Andrei
Warkentin. After patching, we see general purpose partitions like this:
> cat /proc/partitions
179 0 847872 mmcblk0
179 192 4096 mmcblk0gp3
179 160 4096 mmcblk0gp2
179 128 4096 mmcblk0gp1
179 96 1052672 mmcblk0gp0
179 64 1024 mmcblk0boot1
179 32 1024 mmcblk0boot0
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Acked-by: Andrei Warkentin <awarkentin@vmware.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
f39b2dd9d ("mmc: core: Bus width testing needs to handle suspend/resume")
added code to only compare read-only ext_csd fields in bus width testing
code, yet it's comparing some fields that are never set.
The affected fields are ext_csd.raw_erased_mem_count and
ext_csd.raw_partition_support.
Signed-off-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Acked-by: Philip Rakity <prakity@marvell.com>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts
disabled], we run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler returns with
interrupts enabled (see commit [b738a50a: genirq: Warn when handler
enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Intel Medfield platform blocks access to eMMC boot partitions which
results in switch errors. Since there is no access, mmcboot0/1
devices should not be created. Add a host capability to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
In the case of a switch error, do not update partition config as though
the switch succeeded, and ensure blk_end_request is called on the
failed request.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Andrei Warkentin <andrey.warkentin@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the power class selection feature available for mmc
versions 4.0 and above. During the enumeration stage before switching
to the lower data bus, check if the power class is supported for the
current bus width. If the power class is available then switch to the
power class and use the higher data bus. If power class is not supported
then switch to the lower data bus in a worst case.
Signed-off-by: Girish K S <girish.shivananjappa@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Replace setup("fail_mmc_request") and faulty "ifdef KERNEL" with
a simple module_param(). The module param mmc_core.fail_request
may be used to set the fault injection attributes during boot time
or module load time.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds the basic support for imx6q usdhc, which is a
derivative of esdhc controller.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This is a minor fix. It makes mmc_ios_show print proper string when the
host's timing is one of the newly added UHS-I modes.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide platforms with a simplified way to specify MMCIF DMA slave IDs in
a way, similar to SDHI and other sh_dma clients.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
For cards that support hardware reset (just eMMC), try a reset and
retry before returning an I/O error. However this is not done for
ECC errors and is never done twice for the same operation type
(READ, WRITE, DISCARD, SECURE DISCARD) until that type of operation
again succeeds.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
MMC core provides a checking function that checks if the reset
has happended. Add a test to use that function.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add an SDHCI operation for hardware reset and connect it to the
host controller operation.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC's may have a hardware reset line. This patch provides a
host controller operation to implement hardware reset and
a function to reset and reinitialize the card. Also, for MMC,
the reset is always performed before initialization.
The host must set the new host capability MMC_CAP_HW_RESET
to enable hardware reset.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The error condition indicates that mmci_post_request() should cleanup
after the mmci_pre_request(). In this case the resources allocated by
device_prep_slave_sg() are freed by calling dmaengine_terminate_all().
dma_unmap_sg() should always be performed if the host_cookie is set.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The err condition in post_req() is set to undo a call made to pre_req()
that hasn't been started yet. The err condition is not set if an MMC
request returns an error.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Earlier all cards where initiated with bus mode set as OPENDRAIN, and then
later switched to PUSHPULL. According to the MMC/SD/SDIO specifications
only MMC cards use OPENDRAIN during init. For both SD and SDIO the bus
mode shall be PUSHPULL before attempting to init the card.
The consequence of having incorrect bus mode can lead to not being able
to detect the card. Therefore the default behavior have now been changed
to PUSHPULL in mmc_power_up, and will only be temporarily switched when
trying to attach or init a MMC card.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adds a quirk which can be turned on for SDIO devices that do not support
512 byte requests in byte mode during CMD53. These requests will always
be sent in block mode instead.
This patch also enables this quirk for ST-Ericsson CW1200 WLAN device.
Signed-off-by: Stefan Nilsson XK <stefan.xk.nilsson@stericsson.com>
Signed-off-by: Ulf HANSSON <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
During a rescan operation mmc_attach(sd|mmc|sdio) functions are
called. The error handling in these function can trigger a detach
of the bus, which also meant a power off. This is not notified by
the rescan operation which then continues to the next attach function.
If a power off has been done, the framework must never send any
new commands to the host driver, without first doing a new power up.
This will most likely trigger any host driver to hang.
Moving power off out of detach and instead handle power off
separately when it is actually needed, solves the issue.
Signed-off-by: Ulf Hansson <ulf.hansson@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: <stable@kernel.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Currently if card_power_gpio is passed from platform data, it is acquired
and its value is either set or reset. After that we overwrite it with 1,
which is not required.
So, this patch removes the extra line which sets its value.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Freescale eSDHC registers only support 32-bit accesses, this patch
ensures that all Freescale eSDHC register accesses are 32-bit.
Signed-off-by: Xu lei <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Put MMC to sleep if it supports SLEEP/AWAKE (CMD5) in the mmc suspend
so that Vcc (NAND core) can be cut to minimize power consumption.
eMMC put into SLEEP can respond to CMD0 or H/W reset or CMD5.
Current implemention on resume from suspend relies on CMD0 in
mmc_init_card to get out of SLEEP mode.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Venkatraman S <svenkatr@ti.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The default controller configuration which was previously setup by
platform helper functions is moved into the driver.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Stress-testing the runtime power management of libertas_sdio
through a rmmod/insmod loop revealed that it is quite easy to
cause an ETIMEDOUT failure in mmc_sdio_power_restore() leading to:
libertas_sdio: probe of mmc1:0001:1 failed with error -16
Experimentation shows that a very short delay (100us) is needed in
the power down path before the card can be successfully booted again.
We know that this setup is lacking poweroff clamps on the card's power
lines, but as only a short delay is needed, apply this unconditionally.
Also bump up to 1ms sleep for extra legroom.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The previous patch which implemented a DT binding for sdhci-tegra did not
allow all platform data fields to be initialized from DT. The following
were missing:
is_8bit: Implemented by this patch.
pm_flags: Not implemented yet. There are no mainline users of this field.
I'm not quite sure what it's for, and hence how to represent this
in DT; the value ends up being assigned to host->mmc->pm_caps.
While we're at it, fix the binding documentation to refer to "SD/MMC"
instead of "eSDHC", since that's the correct name; "eSDHC" was cut/paste
from the Freescale binding docs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The Patch adds the support for SDIO interrupts for all slots.
It includes enabling of SDIO interrupts through dw_mci_enable_sdio_irq
and the handling of the slot specific interrupts in the Interrupt Service
Routine.
Signed-off-by: Shashidhar Hiremath <shashidharh@vayavyalabs.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
If DMA resource is not available then SDCC driver
should atleast work in PIO data transfer mode.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Intialize busclk_timer before it is accessed in probe.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Not all targets have IRQ1 line routed from the SD controller to
the processor. So we cannot rely on IRQ1 for PIO interrupts.
This patch moves all PIO interrupts to IRQ0 and enables the PIO
mode.
Signed-off-by: Murali Palnati <palnatim@codeaurora.org>
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
On some targets, MCI_IRQ_MASK1 is not routed to the MSM in which
case only "cmd_irq" must be used even for PIO. With this change,
all the targets will use only "cmd_irq" for both CMD and PIO.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
For clocks that support rates which can be set (most clocks other
than _pclk AHB clocks), a rate must be set using clk_set_rate()
before the clock is enabled for the first time with clk_enable().
Subsequent calls to clk_enable() need not be preceded with the
clk_set_rate() calls unless we wish to change the clock rate that
is set previously.
SDC host->clk is currently enabled without setting the clock rate
even once. This patch fixes this, by ensuring that the clock rate
for this clock is first set before enabling the clock.
Signed-off-by: Murali Palnati <palnatim@codeaurora.org>
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
This allows boards with non-standard sdio cards to fill the CIS/CCCR data.
It is particularly important for old msm72k boards using wl1251.
Also drop the obsolete embedded_sdio_data structure from the header
as it was intended to surve a similiar purpose but was not implemented.
Signed-off-by: Alexander Tarasikov <alexander.tarasikov@gmail.com>
Acked-by: Sahitya Tummala <stummala@codeaurora.org>
[davidb: minor formatting cleanup]
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
The use of && instead of || caused a NULL pointer dereference if
gpio setup was not passed via platform data
Signed-off-by: Alexander Tarasikov <alexander.tarasikov@gmail.com>
Acked-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow named IRQs to use corresponding specific handlers. If named IRQs are
used, at least an "sdcard" IRQ has to be specified by the platform. If
names are not used, an arbitrary number of IRQs can be provided by the
platform, in which case the generic ISR will be used for each of them.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
[g.liakhovetski@gmx.de: style and typo corrections, platform data check]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Provide separate interrupt handlers which may be used by platforms where
SDHI has three interrupt sources.
This patch also removes the commented-out handling of CRC and other errors.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
This avoids the need to look up the masks each time an interrupt is handled.
As suggested by Guennadi.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the sparse warning output "warning: Using plain integer as NULL pointer"
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Fix the sparse warning "drivers/mmc/card/queue.c:111:20: warning:
symbol 'mmc_alloc_sg' was not declared. Should it be static?"
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
The individual SoC dependency in Kconfig hardly scales anymore.
Instead of having such a fine grained dependency just depend
on ARCH_MXC and risk that the uninformed user has to look in
the help text to figure out which driver is the correct one.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add hooks to read gpio configuration out of the device tree node.
[grant.likely: Rewrite of original patch from John Bonesio]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[swarren: Fixed tegra_sdhci_get_ro() to retrieve pdata correctly]
[swarren: Reworked to avoid #ifdef CONFIG_OF]
[swarren: Reworked binding based on fsl-imx-esdhc.txt]
[swarren: Documented binding]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Now that we have improved the runtime power management powerup/powerdown
code, we believe that MMC_CAP_POWER_OFF_CARD is no longer necessary:
runtime PM should now work everywhere.
The only hard evidence for introducing MMC_CAP_POWER_OFF_CARD was the
Marvell sd8686 wifi chip, which was believed to require external gpio
manipulation which wasn't supported by some boards.
After further investigation it was realized (and confirmed by Marvell
folks) that sd8686 requirements can be fulfilled by changing the reset
sequence itself, even if no external gpio is manipulated.
For further information, see the following thread:
http://www.mail-archive.com/linux-mmc@vger.kernel.org/msg04289.html
Enable this trivially for a release or two. If no problems are reported,
we will follow up with a more extensive patch to remove this flag
altogether. If problems are reported, we can look at whitelist/blacklist
possibilities as before.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This adds support to inject data errors after a completed host transfer.
The mmc core will return error even though the host transfer is successful.
This simple fault injection proved to be very useful to test the
non-blocking error handling in the mmc_blk_issue_rw_rq().
Random faults can also test how the host driver handles pre_req()
and post_req() in case of errors.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Eanble the ADMA2 mode for freescale esdhc imx driver, tested on MX25
3DS board, MX51 BBG board and MX53 LOCO board.
This patch is only used to enable the ADMA2 for MX51/53 platforms.
MX25/35 can't support the ADMA2 mode, set BROKEN_ADMA quirk on
MX25/35 platforms.
The ADMA mode supported or not can be distinguished by bit 20 of
the Capability Register (offset 0x40) in the FSL eSDHC module.
Signed-off-by: Richard Zhu <richard.zhu@linaro.org>
Tested-and-acked-by: Eric Miao <eric.miao@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
Remove the use of irq_to_gpio() in the card detection interrupt
handler. The information is available in the board structure and
we can avoid using a function that has little meaning.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch fixes a potential issue about PDC interrupts. For example we
have a ENDRX pending interrupt and a RXBUFF pending interrupt. We have
received the RXBUFF interrupt but the transfer is not finished (so we
didn't have time to give a new buffer to the PDC controller). Then we
will compute ENDRX interrupt and we will give a new buffer to the PDC
controller, just after we will compute the RXBUFF interrupt and give
one or two new buffers to the PDC controller but we are not sure that
the first buffer given has been filled. So in this situation we may
have "lost" one sg buffer. It's the same for transmission.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Assuming that a sg buffer size is a page size is false so use sg_dma_len.
A 4096 bytes can be required with two 2048-bytes sg buffer.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Rename atmci_start_command() to atmci_send_command() which is more
appropriate; atmci_start_command suggests we're sending a start command.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add pdc support for atmel-mci. It makes at91-mci driver useless because it
was only used for the old atmel MCI core which has pdc but no dma support.
To allow removing at91-mci, the capabilities of the MCI core are detected
at runtime -- then the driver will use pio, pdc or dma transfers.
Warning: at91rm9200 is not supported, to support it we need to use swab32
on data but I have no board to test it.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Change atmci_readl and atmci_writel macros: remove string concatenation.
We can use these macros with registers which are not prefixed by ATMCI_.
This is the case if we want to write PDC registers which are common to
several devices so they are not prefixed with ATMCI_.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
* 'for-linus' of git://git.open-osd.org/linux-open-osd: (21 commits)
ore: Enable RAID5 mounts
exofs: Support for RAID5 read-4-write interface.
ore: RAID5 Write
ore: RAID5 read
fs/Makefile: Always inspect exofs/
ore: Make ore_calc_stripe_info EXPORT_SYMBOL
ore/exofs: Change ore_check_io API
ore/exofs: Define new ore_verify_layout
ore: Support for partial component table
ore: Support for short read/writes
exofs: Support for short read/writes
ore: Remove check for ios->kern_buff in _prepare_for_striping to later
ore: cleanup: Embed an ore_striping_info inside ore_io_state
ore: Only IO one group at a time (API change)
ore/exofs: Change the type of the devices array (API change)
ore: Make ore_striping_info and ore_calc_stripe_info public
exofs: Remove unused data_map member from exofs_sb_info
exofs: Rename struct ore_components comps => oc
exofs/super.c: local functions should be static
exofs/ore.c: local functions should be static
...
Mark Einon points out that the Kconfig option for NETDEV_1000 no longer
exists, and the merge of the staging drivers should have removed that
for the et131x driver.
And while checking for it, I noticed that slicoss had the same stale
dependency. Remove that one too.
Reported-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
time, s390: Get rid of compile warning
dw_apb_timer: constify clocksource name
time: Cleanup old CONFIG_GENERIC_TIME references that snuck in
time: Change jiffies_to_clock_t() argument type to unsigned long
alarmtimers: Fix error handling
clocksource: Make watchdog reset lockless
posix-cpu-timers: Cure SMP accounting oddities
s390: Use direct ktime path for s390 clockevent device
clockevents: Add direct ktime programming function
clockevents: Make minimum delay adjustments configurable
nohz: Remove "Switched to NOHz mode" debugging messages
proc: Consider NO_HZ when printing idle and iowait times
nohz: Make idle/iowait counter update conditional
nohz: Fix update_ts_time_stat idle accounting
cputime: Clean up cputime_to_usecs and usecs_to_cputime macros
alarmtimers: Rework RTC device selection using class interface
alarmtimers: Add try_to_cancel functionality
alarmtimers: Add more refined alarm state tracking
alarmtimers: Remove period from alarm structure
alarmtimers: Remove interval cap limit hack
...
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
llist: Add back llist_add_batch() and llist_del_first() prototypes
sched: Don't use tasklist_lock for debug prints
sched: Warn on rt throttling
sched: Unify the ->cpus_allowed mask copy
sched: Wrap scheduler p->cpus_allowed access
sched: Request for idle balance during nohz idle load balance
sched: Use resched IPI to kick off the nohz idle balance
sched: Fix idle_cpu()
llist: Remove cpu_relax() usage in cmpxchg loops
sched: Convert to struct llist
llist: Add llist_next()
irq_work: Use llist in the struct irq_work logic
llist: Return whether list is empty before adding in llist_add()
llist: Move cpu_relax() to after the cmpxchg()
llist: Remove the platform-dependent NMI checks
llist: Make some llist functions inline
sched, tracing: Show PREEMPT_ACTIVE state in trace_sched_switch
sched: Remove redundant test in check_preempt_tick()
sched: Add documentation for bandwidth control
sched: Return unused runtime on group dequeue
...
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (121 commits)
perf symbols: Increase symbol KSYM_NAME_LEN size
perf hists browser: Refuse 'a' hotkey on non symbolic views
perf ui browser: Use libslang to read keys
perf tools: Fix tracing info recording
perf hists browser: Elide DSO column when it is set to just one DSO, ditto for threads
perf hists: Don't consider filtered entries when calculating column widths
perf hists: Don't decay total_period for filtered entries
perf hists browser: Honour symbol_conf.show_{nr_samples,total_period}
perf hists browser: Do not exit on tab key with single event
perf annotate browser: Don't change selection line when returning from callq
perf tools: handle endianness of feature bitmap
perf tools: Add prelink suggestion to dso update message
perf script: Fix unknown feature comment
perf hists browser: Apply the dso and thread filters when merging new batches
perf hists: Move the dso and thread filters from hist_browser
perf ui browser: Honour the xterm colors
perf top tui: Give color hints just on the percentage, like on --stdio
perf ui browser: Make the colors configurable and change the defaults
perf tui: Remove unneeded call to newtCls on startup
perf hists: Don't format the percentage on hist_entry__snprintf
...
Fix up conflicts in arch/x86/kernel/kprobes.c manually.
Ingo's tree did the insane "add volatile to const array", which just
doesn't make sense ("volatile const"?). But we could remove the const
*and* make the array volatile to make doubly sure that gcc doesn't
optimize it away..
Also fix up kernel/trace/ring_buffer.c non-data-conflicts manually: the
reader_lock has been turned into a raw lock by the core locking merge,
and there was a new user of it introduced in this perf core merge. Make
sure that new use also uses the raw accessor functions.
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Add IRQF_RESUME_EARLY and resume such IRQs earlier
genirq: Fix fatfinered fixup really
genirq: percpu: allow interrupt type to be set at enable time
genirq: Add support for per-cpu dev_id interrupts
genirq: Add IRQCHIP_SKIP_SET_WAKE flag
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
rtmutex: Add missing rcu_read_unlock() in debug_rt_mutex_print_deadlock()
lockdep: Comment all warnings
lib: atomic64: Change the type of local lock to raw_spinlock_t
locking, lib/atomic64: Annotate atomic64_lock::lock as raw
locking, x86, iommu: Annotate qi->q_lock as raw
locking, x86, iommu: Annotate irq_2_ir_lock as raw
locking, x86, iommu: Annotate iommu->register_lock as raw
locking, dma, ipu: Annotate bank_lock as raw
locking, ARM: Annotate low level hw locks as raw
locking, drivers/dca: Annotate dca_lock as raw
locking, powerpc: Annotate uic->lock as raw
locking, x86: mce: Annotate cmci_discover_lock as raw
locking, ACPI: Annotate c3_lock as raw
locking, oprofile: Annotate oprofilefs lock as raw
locking, video: Annotate vga console lock as raw
locking, latencytop: Annotate latency_lock as raw
locking, timer_stats: Annotate table_lock as raw
locking, rwsem: Annotate inner lock as raw
locking, semaphores: Annotate inner lock as raw
locking, sched: Annotate thread_group_cputimer as raw
...
Fix up conflicts in kernel/posix-cpu-timers.c manually: making
cputimer->cputime a raw lock conflicted with the ABBA fix in commit
bcd5cff721 ("cputimer: Cure lock inversion").
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, ioapic: Consolidate the explicit EOI code
x86, ioapic: Restore the mask bit correctly in eoi_ioapic_irq()
x86, kdump, ioapic: Reset remote-IRR in clear_IO_APIC
iommu: Rename the DMAR and INTR_REMAP config options
x86, ioapic: Define irq_remap_modify_chip_defaults()
x86, msi, intr-remap: Use the ioapic set affinity routine
iommu: Cleanup ifdefs in detect_intel_iommu()
iommu: No need to set dmar_disabled in check_zero_address()
iommu: Move IOMMU specific code to intel-iommu.c
intr_remap: Call dmar_dev_scope_init() explicitly
x86, x2apic: Enable the bios request for x2apic optout
* 'staging-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1519 commits)
staging: et131x: Remove redundant check and return statement
staging: et131x: Mainly whitespace changes to appease checkpatch
staging: et131x: Remove last of the forward declarations
staging: et131x: Remove even more forward declarations
staging: et131x: Remove yet more forward declarations
staging: et131x: Remove more forward declarations
staging: et131x: Remove forward declaration of et131x_adapter_setup
staging: et131x: Remove some forward declarations
staging: et131x: Remove unused rx_ring.recv_packet_pool
staging: et131x: Remove call to find pci pm capability
staging: et131x: Remove redundant et131x_reset_recv() call
staging: et131x: Remove unused rx_ring.recv_buffer_pool
Staging: bcm: Fix three initialization errors in InterfaceDld.c
Staging: bcm: Fix coding style issues in InterfaceDld.c
staging:iio:dac: Add AD5360 driver
staging:iio:trigger:bfin-timer: Fix compile error
Staging: vt6655: add some range checks before memcpy()
Staging: vt6655: whitespace fixes to iotcl.c
Staging: vt6656: add some range checks before memcpy()
Staging: vt6656: whitespace cleanups in ioctl.c
...
Fix up conflicts in:
- drivers/{Kconfig,Makefile}, drivers/staging/{Kconfig,Makefile}:
vg driver movement
- drivers/staging/brcm80211/brcmfmac/{dhd_linux.c,mac80211_if.c}:
driver removal vs now stale changes
- drivers/staging/rtl8192e/r8192E_core.c:
driver removal vs now stale changes
- drivers/staging/et131x/et131*:
driver consolidation into one file, tried to do fixups
* 'tty-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
TTY: serial_core: Fix crash if DCD drop during suspend
tty/serial: atmel_serial: bootconsole removed from auto-enumerates
Revert "TTY: call tty_driver_lookup_tty unconditionally"
tty/serial: atmel_serial: add device tree support
tty/serial: atmel_serial: auto-enumerate ports
tty/serial: atmel_serial: whitespace and braces modifications
tty/serial: atmel_serial: change platform_data variable name
tty/serial: RS485 bindings for device tree
TTY: call tty_driver_lookup_tty unconditionally
TTY: pty, release tty in all ptmx_open fail paths
TTY: make tty_add_file non-failing
TTY: drop driver reference in tty_open fail path
8250_pci: Fix kernel panic when pch_uart is disabled
h8300: drivers/serial/Kconfig was moved
parport_pc: release IO region properly if unsupported ITE887x card is found
tty: Support compat_ioctl get/set termios_locked
hvc_console: display printk messages on console.
TTY: snyclinkmp: forever loop in tx_load_dma_buffer()
tty/n_gsm: avoid fifo overflow in gsm_dlci_data_output
tty/n_gsm: fix a bug in gsm_dlci_data_output (adaption = 2 case)
...
Fix up Conflicts in:
- drivers/tty/serial/8250_pci.c
Trivial conflict with removed duplicate device ID
- drivers/tty/serial/atmel_serial.c
Annoying silly conflict between "specify the port num via
platform_data" and other changes to atmel_console_init
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (26 commits)
hwmon: (w83627ehf) Better fix for negative temperature values
hwmon: (w83627ehf) Uninline is_word_sized
hwmon: (lm75) Document why clones are not detected
hwmon: (w83627ehf) Move fan pins check to a separate function
hwmon: (w83627ehf) Skip reading unused voltage registers
hwmon: (lm75) Add support for Analog Devices ADT75
hwmon: (pmbus_core) Simplify sign extensions
hwmon: (pmbus) Add support for Lineage Power DC-DC converters
hwmon: (pmbus/ltc2978) Add support for LTC3880 to LTC2978 driver
hwmon: (pmbus/ltc2978) Explicit driver for LTC2978
hwmon: (pmbus) Add support for TEMP2 peak attributes
hwmon: AD7314 driver (ported from IIO)
hwmon: (pmbus) Add support for Intersil power management chips
hwmon: (pmbus) Always call _pmbus_read_byte in core driver
hwmon: (pmbus) Replace EINVAL return codes with more appropriate errors
hwmon: (pmbus) Provide more documentation
hwmon/f71882fg: Make the decision wether to register fan attr. per fan
hwmon/f71882fg: Add a f71882fg_create_fan_sysfs_files helper function
hwmon/f71882fg: Make all fan/pwm attr tables 2 dimensional
hwmon: (exynos4_tmu) Remove IRQF_DISABLED
...
In 3.0 we changed the way recovery_disabled was handle so that instead
of testing against zero, we test an mddev-> value against a conf->
value.
Two problems:
1/ one place in raid1 was missed and still sets to '1'.
2/ We didn't explicitly set the conf-> value at array creation
time.
It defaulted to '0' just like the mddev value does so they
could appear equal and thus disable recovery.
This did not affect normal 'md' as it calls bind_rdev_to_array
which changes the mddev value. However the dmraid interface
doesn't call this and so doesn't change ->recovery_disabled; so at
array start all recovery is incorrectly disabled.
So initialise the 'conf' value to one less that the mddev value, so
the will only be the same when explicitly set that way.
Reported-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This bug was introduced in 415e72d034
which was in 2.6.36.
There is a small window of time between when a device fails and when
it is removed from the array. During this time we might still read
from it, but we won't write to it - so it is possible that we could
read stale data.
We didn't need the test of 'Faulty' before because the test on
In_sync is sufficient. Since we started allowing reads from the early
part of non-In_sync devices we need a test on Faulty too.
This is suitable for any kernel from 2.6.36 onwards, though the patch
might need a bit of tweaking in 3.0 and earlier.
Cc: stable@kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This simplifies the init/shutdown paths, and makes client->msgr available
during the rest of the setup process.
Signed-off-by: Sage Weil <sage@newdream.net>
* 'pm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (63 commits)
PM / Clocks: Remove redundant NULL checks before kfree()
PM / Documentation: Update docs about suspend and CPU hotplug
ACPI / PM: Add Sony VGN-FW21E to nonvs blacklist.
ARM: mach-shmobile: sh7372 A4R support (v4)
ARM: mach-shmobile: sh7372 A3SP support (v4)
PM / Sleep: Mark devices involved in wakeup signaling during suspend
PM / Hibernate: Improve performance of LZO/plain hibernation, checksum image
PM / Hibernate: Do not initialize static and extern variables to 0
PM / Freezer: Make fake_signal_wake_up() wake TASK_KILLABLE tasks too
PM / Hibernate: Add resumedelay kernel param in addition to resumewait
MAINTAINERS: Update linux-pm list address
PM / ACPI: Blacklist Vaio VGN-FW520F machine known to require acpi_sleep=nonvs
PM / ACPI: Blacklist Sony Vaio known to require acpi_sleep=nonvs
PM / Hibernate: Add resumewait param to support MMC-like devices as resume file
PM / Hibernate: Fix typo in a kerneldoc comment
PM / Hibernate: Freeze kernel threads after preallocating memory
PM: Update the policy on default wakeup settings
PM / VT: Cleanup #if defined uglyness and fix compile error
PM / Suspend: Off by one in pm_suspend()
PM / Hibernate: Include storage keys in hibernation image on s390
...
* 'for-next' of git://git.linaro.org/people/triad/linux-pinctrl:
pinctrl/sirf: fix sirfsoc_get_group_pins prototype
pinctrl: Don't copy function name when requesting a pin
pinctrl: Don't copy pin names when registering them
pinctrl: Remove unsafe __refdata
pinctrl: get_group_pins() const fixes
pinctrl: add a driver for the CSR SiRFprimaII pinmux
pinctrl: add a driver for the U300 pinmux
drivers: create a pin control subsystem
* 'for-linus' of git://opensource.wolfsonmicro.com/regmap: (62 commits)
mfd: Enable rbtree cache for wm831x devices
regmap: Support some block operations on cached devices
regmap: Allow caches for devices with no defaults
regmap: Ensure rbtree syncs registers set to zero properly
regmap: Allow rbtree to cache zero default values
regmap: Warn on raw I/O as well as bulk reads that bypass cache
regmap: Return a sensible error code if we fail to read the cache
regmap: Use bsearch() to search the register defaults
regmap: Fix doc comment
regmap: Optimize the lookup path to use binary search
regmap: Ensure we scream if we enable cache bypass/only at the same time
regmap: Implement regcache_cache_bypass helper function
regmap: Save/restore the bypass state upon syncing
regmap: Lock the sync path, ensure we use the lockless _regmap_write()
regmap: Fix apostrophe usage
regmap: Make _regmap_write() global
regmap: Fix lock used for regcache_cache_only()
regmap: Grab the lock in regcache_cache_only()
regmap: Modify map->cache_bypass directly
regmap: Fix regcache_sync generic implementation
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits)
dp83640: free packet queues on remove
dp83640: use proper function to free transmit time stamping packets
ipv6: Do not use routes from locally generated RAs
|PATCH net-next] tg3: add tx_dropped counter
be2net: don't create multiple RX/TX rings in multi channel mode
be2net: don't create multiple TXQs in BE2
be2net: refactor VF setup/teardown code into be_vf_setup/clear()
be2net: add vlan/rx-mode/flow-control config to be_setup()
net_sched: cls_flow: use skb_header_pointer()
ipv4: avoid useless call of the function check_peer_pmtu
TCP: remove TCP_DEBUG
net: Fix driver name for mdio-gpio.c
ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT
rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces
ipv4: fix ipsec forward performance regression
jme: fix irq storm after suspend/resume
route: fix ICMP redirect validation
net: hold sock reference while processing tx timestamps
tcp: md5: add more const attributes
Add ethtool -g support to virtio_net
...
Fix up conflicts in:
- drivers/net/Kconfig:
The split-up generated a trivial conflict with removal of a
stale reference to Documentation/networking/net-modules.txt.
Remove it from the new location instead.
- fs/sysfs/dir.c:
Fairly nasty conflicts with the sysfs rb-tree usage, conflicting
with Eric Biederman's changes for tagged directories.
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (260 commits)
usb: renesas_usbhs: fixup inconsistent return from usbhs_pkt_push()
usb/isp1760: Allow to optionally trigger low-level chip reset via GPIOLIB.
USB: gadget: midi: memory leak in f_midi_bind_config()
USB: gadget: midi: fix range check in f_midi_out_open()
QE/FHCI: fixed the CONTROL bug
usb: renesas_usbhs: tidyup for smatch warnings
USB: Fix USB Kconfig dependency problem on 85xx/QoirQ platforms
EHCI: workaround for MosChip controller bug
usb: gadget: file_storage: fix race on unloading
USB: ftdi_sio.c: Use ftdi async_icount structure for TIOCMIWAIT, as in other drivers
USB: ftdi_sio.c:Fill MSR fields of the ftdi async_icount structure
USB: ftdi_sio.c: Fill LSR fields of the ftdi async_icount structure
USB: ftdi_sio.c:Fill TX field of the ftdi async_icount structure
USB: ftdi_sio.c: Fill the RX field of the ftdi async_icount structure
USB: ftdi_sio.c: Basic icount infrastructure for ftdi_sio
usb/isp1760: Let OF bindings depend on general CONFIG_OF instead of PPC_OF .
USB: ftdi_sio: Support TI/Luminary Micro Stellaris BD-ICDI Board
USB: Fix runtime wakeup on OHCI
xHCI/USB: Make xHCI driver have a BOS descriptor.
usb: gadget: add new usb gadget for ACM and mass storage
...
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (38 commits)
mm: memory hotplug: Check if pages are correctly reserved on a per-section basis
Revert "memory hotplug: Correct page reservation checking"
Update email address for stable patch submission
dynamic_debug: fix undefined reference to `__netdev_printk'
dynamic_debug: use a single printk() to emit messages
dynamic_debug: remove num_enabled accounting
dynamic_debug: consolidate repetitive struct _ddebug descriptor definitions
uio: Support physical addresses >32 bits on 32-bit systems
sysfs: add unsigned long cast to prevent compile warning
drivers: base: print rejected matches with DEBUG_DRIVER
memory hotplug: Correct page reservation checking
memory hotplug: Refuse to add unaligned memory regions
remove the messy code file Documentation/zh_CN/SubmitChecklist
ARM: mxc: convert device creation to use platform_device_register_full
new helper to create platform devices with dma mask
docs/driver-model: Update device class docs
docs/driver-model: Document device.groups
kobj_uevent: Ignore if some listeners cannot handle message
dynamic_debug: make netif_dbg() call __netdev_printk()
dynamic_debug: make netdev_dbg() call __netdev_printk()
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (59 commits)
MAINTAINERS: linux-m32r is moderated for non-subscribers
linux@lists.openrisc.net is moderated for non-subscribers
Drop default from "DM365 codec select" choice
parisc: Kconfig: cleanup Kernel page size default
Kconfig: remove redundant CONFIG_ prefix on two symbols
cris: remove arch/cris/arch-v32/lib/nand_init.S
microblaze: add missing CONFIG_ prefixes
h8300: drop puzzling Kconfig dependencies
MAINTAINERS: microblaze-uclinux@itee.uq.edu.au is moderated for non-subscribers
tty: drop superfluous dependency in Kconfig
ARM: mxc: fix Kconfig typo 'i.MX51'
Fix file references in Kconfig files
aic7xxx: fix Kconfig references to READMEs
Fix file references in drivers/ide/
thinkpad_acpi: Fix printk typo 'bluestooth'
bcmring: drop commented out line in Kconfig
btmrvl_sdio: fix typo 'btmrvl_sdio_sd6888'
doc: raw1394: Trivial typo fix
CIFS: Don't free volume_info->UNC until we are entirely done with it.
treewide: Correct spelling of successfully in comments
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/apm:
apm-emulation: use wait_event_freezable() instead of freezer_[do_not_]count()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (61 commits)
HID: hid-magicmouse: Magic Trackpad has 1 button, not 2
HID: Add device IDs for more SJOY adapters
HID: primax: remove spurious dependency
HID: support primax keyboards violating USB HID spec
HID: usbhid: cancel timer for retry synchronously
HID: wacom: Set input bits before registration
HID: consolidate MacbookAir 4,1 mappings
HID: MacbookAir4,1 and MacbookAir4,2 need entry in hid_mouse_ignore_list[]
HID: Add support MacbookAir 4,1 keyboard
HID: hidraw: open count should not increase if error
HID: hiddev: potential info leak in hiddev_ioctl()
HID: multitouch: decide if hid-multitouch needs to handle mt devices
HID: add autodetection of multitouch devices
HID: "hid-logitech" driver with Logitech Driving Force GT
HID: hid-logitech-dj: fix off by one
HID: hidraw: protect hidraw_disconnect() better
HID: hid-multitouch: add support for the IDEACOM 6650 chip
HID: Add full support for Logitech Unifying receivers
HID: hidraw: free list for all error in hidraw_open
HID: roccat: Kone now reports external profile changes via roccat device
...
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (62 commits)
target: Fix compile warning w/ missing module.h include
target: Remove legacy se_task->task_timer and associated logic
target: Fix incorrect transport_sent usage
target: re-use the command S/G list for single-task commands
target: Fix BIDI t_task_cdb handling in transport_generic_new_cmd
target: remove transport_allocate_tasks
target: merge transport_new_cmd_obj into transport_generic_new_cmd
target: remove the task_sg_bidi field se_task and pSCSI BIDI support
target: transport_subsystem_check_init cleanups
target: use a workqueue for I/O completions
target: remove unused TRANSPORT_ states
target: remove TRANSPORT_DEFERRED_CMD state
target: remove the TRANSPORT_REMOVE state
target: move depth_left manipulation out of transport_generic_request_failure
target: stop task timers earlier
target: remove TF_TIMER_STOP
target: factor some duplicate code for stopping a task
target: fix list walking in transport_free_dev_tasks
target: use transport_cmd_check_stop_to_fabric consistently
target: do not pass the queue object to transport_remove_cmd_from_queue
...
fix sirfsoc_get_group_pins prototype introduced in 7e570f97, we
missed to de-constify a pointer.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* 'next' of git://selinuxproject.org/~jmorris/linux-security: (95 commits)
TOMOYO: Fix incomplete read after seek.
Smack: allow to access /smack/access as normal user
TOMOYO: Fix unused kernel config option.
Smack: fix: invalid length set for the result of /smack/access
Smack: compilation fix
Smack: fix for /smack/access output, use string instead of byte
Smack: domain transition protections (v3)
Smack: Provide information for UDS getsockopt(SO_PEERCRED)
Smack: Clean up comments
Smack: Repair processing of fcntl
Smack: Rule list lookup performance
Smack: check permissions from user space (v2)
TOMOYO: Fix quota and garbage collector.
TOMOYO: Remove redundant tasklist_lock.
TOMOYO: Fix domain transition failure warning.
TOMOYO: Remove tomoyo_policy_memory_lock spinlock.
TOMOYO: Simplify garbage collector.
TOMOYO: Fix make namespacecheck warnings.
target: check hex2bin result
encrypted-keys: check hex2bin result
...
* 'stable/drivers-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xenbus: don't rely on xen_initial_domain to detect local xenstore
xenbus: Fix loopback event channel assuming domain 0
xen/pv-on-hvm:kexec: Fix implicit declaration of function 'xen_hvm_domain'
xen/pv-on-hvm kexec: add xs_reset_watches to shutdown watches from old kernel
xen/pv-on-hvm kexec: update xs_wire.h:xsd_sockmsg_type from xen-unstable
xen/pv-on-hvm kexec+kdump: reset PV devices in kexec or crash kernel
xen/pv-on-hvm kexec: rebind virqs to existing eventchannel ports
xen/pv-on-hvm kexec: prevent crash in xenwatch_thread() when stale watch events arrive
* 'stable/drivers.bugfixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pciback: Check if the device is found instead of blindly assuming so.
xen/pciback: Do not dereference psdev during printk when it is NULL.
xen: remove XEN_PLATFORM_PCI config option
xen: XEN_PVHVM depends on PCI
xen/pciback: double lock typo
xen/pciback: use mutex rather than spinlock in vpci backend
xen/pciback: Use mutexes when working with Xenbus state transitions.
xen/pciback: miscellaneous adjustments
xen/pciback: use mutex rather than spinlock in passthrough backend
xen/pciback: use resource_size()
* 'stable/pci.fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/pci: support multi-segment systems
xen-swiotlb: When doing coherent alloc/dealloc check before swizzling the MFNs.
xen/pci: make bus notifier handler return sane values
xen-swiotlb: fix printk and panic args
xen-swiotlb: Fix wrong panic.
xen-swiotlb: Retry up three times to allocate Xen-SWIOTLB
xen-pcifront: Update warning comment to use 'e820_host' option.
This was done to resolve a conflict in the
drivers/staging/comedi/drivers/ni_labpc.c file that resolved a build
bugfix in Linus's tree with a "better" bugfix that was in the
staging-next tree that resolved the issue in a more complete manner.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'stable/bug.fixes-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/p2m/debugfs: Make type_name more obvious.
xen/p2m/debugfs: Fix potential pointer exception.
xen/enlighten: Fix compile warnings and set cx to known value.
xen/xenbus: Remove the unnecessary check.
xen/irq: If we fail during msi_capability_init return proper error code.
xen/events: Don't check the info for NULL as it is already done.
xen/events: BUG() when we can't allocate our event->irq array.
* 'stable/mmu.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: Fix selfballooning and ensure it doesn't go too far
xen/gntdev: Fix sleep-inside-spinlock
xen: modify kernel mappings corresponding to granted pages
xen: add an "highmem" parameter to alloc_xenballooned_pages
xen/p2m: Use SetPagePrivate and its friends for M2P overrides.
xen/p2m: Make debug/xen/mmu/p2m visible again.
Revert "xen/debug: WARN_ON when identity PFN has no _PAGE_IOMAP flag set."
* 'stable/e820-3.2' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: release all pages within 1-1 p2m mappings
xen: allow extra memory to be in multiple regions
xen: allow balloon driver to use more than one memory region
xen/balloon: simplify test for the end of usable RAM
xen/balloon: account for pages released during memory setup
This patch fixes the following compile warning in target_core_cdb.c in
recent linux-next code due to the new use of EXPORT_SYMBOL() for
target_get_task_cdb().
drivers/target/target_core_cdb.c:1316: warning: data definition has no type or storage class
drivers/target/target_core_cdb.c:1316: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
drivers/target/target_core_cdb.c:1316: warning: parameter names (without types) in function declaration
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The "phy_device_register()" call 5 lines down already calls
phy_scan_fixups(), there's no need to do it a second time.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
If the PHY should disappear (for example, on an USB Ethernet MAC), then
the driver would leak any undelivered time stamp packets. This commit
fixes the issue by calling the appropriate functions to free any packets
left in the transmit and receive queues.
The driver first appeared in v3.0.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous commit enforces a new rule for handling the cloned packets
for transmit time stamping. These packets must not be freed using any other
function than skb_complete_tx_timestamp. This commit fixes the one and only
driver using this API.
The driver first appeared in v3.0.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a frame cant be transmitted, it is silently discarded.
Add a counter to report these errors to user.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the HW is in multi-channel mode based on the skew/IPL, there are
4 functions per port and so not enough resources to create multiple
RX/TX rings for each function.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple TXQ support is partially broken in BE2. It is fully
supported BE3 onwards and in Lancer.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the code for VF setup/teardown done by a PF (if_create,
mac_add_config, link_status_query etc) is scattered; this patch
refactors this code into be_vf_setup() and be_vf_clear(). The
if_create/if_destroy/mac_addr_query cmds are now called after the MCCQ
is created; so these cmds are now modified to use the MCCQ instead of
MBOX.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a card is reset due to EEH error recovery or due to a suspend,
rx-mode config (promisc/mc) is not being sent to the FW. be_setup() is
called in these flows and is the best place for such config/re-config
cmds. Hence include rx-mode, vlan and flow-control config in
be_setup().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For simple modules that contain a single platform_driver without any
additional setup code then ends up being a block of duplicated
boilerplate. This patch adds a new macro, module_platform_driver(),
which replaces the module_init()/module_exit() registrations with
template functions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Magnus Damm <magnus.damm@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Since commit
"7488876... dt/net: Eliminate users of of_platform_{,un}register_driver"
there are two platform drivers named "mdio-gpio" registered.
I renamed the of variant to "mdio-ofgpio".
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
zorro-driver.c: fix four checkpatch warnings of:
WARNING: EXPORT_SYMBOL(foo); should immediately follow its function/variable
I had a cat. The cat was mine.
His name was Zorro. Amiga is fine.
Signed-off-by: Jim Rotmalm <jim.rotmalm@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
It is more efficient to left-align 8-bit temperature values, so that
8-bit and 9-bit temperature values can be handled exactly the same way
in the rest of the code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Helper function is_word_sized has grown too much to be kept inline. It
was OK when there were only 6 word-sized registers but support for new
devices have made the list much longer. The function is also called
from more places than before.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Explain why clones of the LM75 are generally not detected by the
driver, and why this isn't going to change. Also update the
documentation to reflect the list of chip names currently supported by
the driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Move the check of fan pin usage to a separate function. This improves
readability, and will make it easier to integrate chip-specific
conditions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
When in6 is missing, don't read the corresponding registers, it's a
waste of time. The logic is similar to what we do for fans and
temperatures.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Add datasheet reference and device ID for ADT75.
The ADT75, like some other LM75 derivatives, needs to be instantiated
using methods 1, 2, or 4.
For more information see Documentation/i2c/instantiating-devices.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Shift operations can be used for sign extensions. Use it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add device IDs and reference to datasheets for Lineage Power DC-DC converters.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
The LTC3880 PMBus command set is comparable to LTC2978. Add support for it
to the LTC2978 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Provide explicit driver for LTC2978 to enable support for minimum and peak
attributes. Remove ltc2978 chip id from generic pmbus driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
At least one PMBus chip supports peak attributes for READ_TEMPERATURE2.
Add virtual registers to be able to report it to the user.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Driver for AD7314, ADT7301, and ADT7302, ported from IIO.
Currently dropped power down mode support.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
[guenter.roeck@ericsson.com: Added MODULE_DEVICE_TABLE]
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Always call _pmbus_read_byte() instead of pmbus_read_byte() in PMBus core
driver. With this change, device specific read functions can be implemented for
all registers.
Since the device specific read_byte function is now always called, we need to be
more careful with page validations. Only fail if the passed page number is larger
than 0, since -1 means "current page".
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
EINVAL was over-used in the code. Replace it with more appropriate errors.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Before this patch the f71882fg driver completely fails to initialize
on systems which have reserved settings in the pwm enable register, and
it disables all auto pwm sysfs attributes if any fan is controlled by
a digital sensor reading.
This patch changes the fail to initialize into don't register any attributes
for the fan for which there are reserved settings in the pwm enable register
and also makes the not registering of auto pwm sysfs attributes a per fan
thing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This is a preparation patch for not registering fan/pwm attributes for
some fans (rather then register them for all or for none).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This is a preparation patch for not registering fan/pwm attributes for
some fans (rather then register them for all or for none).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Since commit [c58543c8: genirq: Run irq handlers with interrupts disabled],
we run all interrupt handlers with interrupts disabled
and we even check and yell when an interrupt handler
returns with interrupts enabled (see commit [b738a50a:
genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
This patch allows to read temperature
from TMU(Thermal Management Unit) of SAMSUNG EXYNOS4 series of SoC.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
ADM1276 is mostly compatible to ADM1275, with added support for input power
measurement. Add support for it to the ADM1275 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
ADM1275 supports a second current limit, which can be configured as either lower
or upper limit. Add support for it and report it as either lower or upper
critical current limit.
Also replace error return code EINVAL for unsupported pages with ENXIO as this
is more appropriate for the observed condition.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Driver remove functions have an error return value, but rarely return an error
in practice. If a driver does return an error from its remove function, the
driver won't be unloaded and is expected to stay alive.
pmbus_do_remove() is defined as returning an int, but always returns 0 (no
error). Calling code passes that return value on to high level driver
remove functions, but does not evaluate it and removes driver data even if
pmbus_do_remove() returned an error (which it in practice never does). Even if
this code could never cause a real problem, it is nevertheless conceptually
wrong.
To reduce confusion and simplify the code, change pmbus_do_remove() to be a void
function, and have PMBus client drivers always return zero in their driver
remove functions.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Return values for functions reading/writing manufacturer specific registers are
poorly explained. Add comments to improve documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Export caseopen alarm status into userspace for Winbond W83627*
and Nuvoton NCT677[56] chips and implement alarm clear attribute.
Second caseopen alarm on NCT6776 is also supported.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
