Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch,
perf) friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the kfree_skb() by consume_skb() to be drop monitor(dropwatch,
perf) friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The XGBE hardware has support for performing MDIO operations using an
MDIO command request. The driver mistakenly uses the mdio port address
as the MDIO command request device address instead of the MDIO command
request port address. Additionally, the driver does not properly check
for and create a clause 45 MDIO command.
Check the supplied MDIO register to determine if the request is a clause
45 operation (MII_ADDR_C45). For a clause 45 operation, extract the device
address and register number from the supplied MDIO register and use them
to set the MDIO command request device address and register number fields.
For a clause 22 operation, the MDIO request device address is set to zero
and the MDIO command request register number is set to the supplied MDIO
register. In either case, the supplied MDIO port address is used as the
MDIO command request port address.
Fixes: 732f2ab7af ("amd-xgbe: Add support for MDIO attached PHYs")
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Tested-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy drivers for CS4340 and TN2020 are missing their
features attributes. Add them.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As txq_trans_update() only updates trans_start when the lock is held,
trans_start does not get updated if NETIF_F_LLTX is declared.
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb header should be set to ethernet header before using
is_skb_forwardable. Because the ethernet header length has been
considered in is_skb_forwardable(including dev->hard_header_len
length).
To reproduce the issue:
1, add 2 ports on linux bridge br using following commands:
$ brctl addbr br
$ brctl addif br eth0
$ brctl addif br eth1
2, the MTU of eth0 and eth1 is 1500
3, send a packet(Data 1480, UDP 8, IP 20, Ethernet 14, VLAN 4)
from eth0 to eth1
So the expect result is packet larger than 1500 cannot pass through
eth0 and eth1. But currently, the packet passes through success, it
means eth1's MTU limit doesn't take effect.
Fixes: f6367b4660 ("bridge: use is_skb_forwardable in forward path")
Cc: bridge@lists.linux-foundation.org
Cc: Nkolay Aleksandrov <nikolay@cumulusnetworks.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vhost dirty page logging API is designed to sync through GPA. But we
try to log GIOVA when device IOTLB is enabled. This is wrong and may
lead to missing data after migration.
To solve this issue, when logging with device IOTLB enabled, we will:
1) reuse the device IOTLB translation result of GIOVA->HVA mapping to
get HVA, for writable descriptor, get HVA through iovec. For used
ring update, translate its GIOVA to HVA
2) traverse the GPA->HVA mapping to get the possible GPA and log
through GPA. Pay attention this reverse mapping is not guaranteed
to be unique, so we should log each possible GPA in this case.
This fix the failure of scp to guest during migration. In -next, we
will probably support passing GIOVA->GPA instead of GIOVA->HVA.
Fixes: 6b1e6cc785 ("vhost: new device IOTLB API")
Reported-by: Jintack Lim <jintack@cs.columbia.edu>
Cc: Jintack Lim <jintack@cs.columbia.edu>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net_tstamp.h is an UAPI header, so it was moved under include/uapi.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit cb9f1b7838, scapy (which uses an AF_PACKET socket in
SOCK_RAW mode) is unable to send a basic icmp packet over a sit tunnel:
Here is a example of the setup:
$ ip link set ntfp2 up
$ ip addr add 10.125.0.1/24 dev ntfp2
$ ip tunnel add tun1 mode sit ttl 64 local 10.125.0.1 remote 10.125.0.2 dev ntfp2
$ ip addr add fd00:cafe:cafe::1/128 dev tun1
$ ip link set dev tun1 up
$ ip route add fd00:200::/64 dev tun1
$ scapy
>>> p = []
>>> p += IPv6(src='fd00💯:1', dst='fd00:200::1')/ICMPv6EchoRequest()
>>> send(p, count=1, inter=0.1)
>>> quit()
$ ip -s link ls dev tun1 | grep -A1 "TX.*errors"
TX: bytes packets errors dropped carrier collsns
0 0 1 0 0 0
The problem is that the network offset is set to the hard_header_len of the
output device (tun1, ie 14 + 20) and in our case, because the packet is
small (48 bytes) the pskb_inet_may_pull() fails (it tries to pull 40 bytes
(ipv6 header) starting from the network offset).
This problem is more generally related to device with variable hard header
length. To avoid a too intrusive patch in the current release, a (ugly)
workaround is proposed in this patch. It has to be cleaned up in net-next.
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=993675a3100b1
Link: http://patchwork.ozlabs.org/patch/1024489/
Fixes: cb9f1b7838 ("ip: validate header length on virtual device xmit")
CC: Willem de Bruijn <willemb@google.com>
CC: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 23b0269e58 ("net: udp6: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.
This is related to the problem addressed in the commit 719f835853
("udp: add rehash on connect()"). Moreover, __udp6_lib_lookup() now
looks for a socket immediately in the secondary hash table.
And this issue was found with LTP/network tests as well.
Fixes: 23b0269e58 ("net: udp6: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 4cdeeee925 ("net: udp: prefer listeners bound to an
address"), UDP-Lite only works when specifying a local address for
the sockets.
This is related to the problem addressed in the commit 719f835853
("udp: add rehash on connect()"). Moreover, __udp4_lib_lookup() now
looks for a socket immediately in the secondary hash table.
The issue was found with LTP/network tests (UDP-Lite test-cases).
Fixes: 4cdeeee925 ("net: udp: prefer listeners bound to an address")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes (especially 05cd271fd6 ("cls_flower: Support multiple
masks per priority")) in the fl_flow_mask structure grow it and its
current size e.g. on x86_64 with defconfig is 760 bytes and more than
1024 bytes with some debug options enabled. Prior the mentioned commit
its size was 176 bytes (using defconfig on x86_64).
With regard to this fact it's reasonable to allocate this structure
dynamically in fl_change() to reduce its stack size.
v2:
- use kzalloc() instead of kcalloc()
Fixes: 05cd271fd6 ("cls_flower: Support multiple masks per priority")
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Paul Blakey <paulb@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new of_get_compatible_child() helper to look up child nodes to
avoid ever matching non-child nodes elsewhere in the tree.
Also fix up the related struct device_node leaks.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Cc: stable <stable@vger.kernel.org> # 4.19: 36156f9241
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shifting the 1 by exp by an int can lead to sign-extension overlow when
exp is 31 since 1 is an signed int and sign-extending this result to an
unsigned long long will set the upper 32 bits. Fix this by shifting an
unsigned long.
Detected by cppcheck:
(warning) Shifting signed 32-bit value by 31 bits is undefined behaviour
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failure __ip_append_data triggers udp_flush_pending_frames, but these
tests happen later. The skb must be freed directly.
Fixes: bec1f6f697 ("udp: generate gso with UDP_SEGMENT")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The section of bpfilter UMH blob is the ".bpfilter_umh". but this is not
an explicit section. so linking warning occurred at compile time for the
powerpc.
So, this patch makes use of the ".rodata" instead of the ".bpfilter_umh".
Config condition:
CONFIG_BPFILTER=y
CONFIG_BPFILTER_UMH=y
Result:
ld: warning: orphan section `.bpfilter_umh' from
`net/bpfilter/bpfilter_umh_blob.o' being placed in section `.bpfilter_umh'
Fixes: 61fbf5933d ("net: bpfilter: restart bpfilter_umh when error occurred")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm87xx and micrel driver has PHYs which are missing the .features
value. Add them. The bcm87xx is a 10G FEC only PHY. Add the needed
features definition of this PHY.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Reported-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
"IPv6: " prefix is already added by pr_fmt, no need to include
it again in the pr_warn() format. The message predates extack
support, we can replace the whole thing with an extack message.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In iproute2 commit 90c5c969f0b9 ("fix print_0xhex on 32 bit"), the format
specifier for the ife type changed from 0x%X to %#llX, causing systematic
failures in the following TDC test cases:
7682 - Create valid ife encode action with mark and pass control
ef47 - Create valid ife encode action with mark and pipe control
df43 - Create valid ife encode action with mark and continue control
e4cf - Create valid ife encode action with mark and drop control
ccba - Create valid ife encode action with mark and reclassify control
a1cf - Create valid ife encode action with mark and jump control
cb3d - Create valid ife encode action with mark value at 32-bit maximum
95ed - Create valid ife encode action with prio and pass control
aa17 - Create valid ife encode action with prio and pipe control
74c7 - Create valid ife encode action with prio and continue control
7a97 - Create valid ife encode action with prio and drop control
f66b - Create valid ife encode action with prio and reclassify control
3056 - Create valid ife encode action with prio and jump control
7dd3 - Create valid ife encode action with prio value at 32-bit maximum
05bb - Create valid ife encode action with tcindex and pass control
ce65 - Create valid ife encode action with tcindex and pipe control
09cd - Create valid ife encode action with tcindex and continue control
8eb5 - Create valid ife encode action with tcindex and continue control
451a - Create valid ife encode action with tcindex and drop control
d76c - Create valid ife encode action with tcindex and reclassify control
e731 - Create valid ife encode action with tcindex and jump control
b7b8 - Create valid ife encode action with tcindex value at 16-bit maximum
2a9c - Create valid ife encode action with mac src parameter
cf5c - Create valid ife encode action with mac dst parameter
2353 - Create valid ife encode action with mac src and mac dst parameters
552c - Create valid ife encode action with mark and type parameters
0421 - Create valid ife encode action with prio and type parameters
4017 - Create valid ife encode action with tcindex and type parameters
fac3 - Create valid ife encode action with index at 32-bit maximnum
7c25 - Create valid ife decode action with pass control
dccb - Create valid ife decode action with pipe control
7bb9 - Create valid ife decode action with continue control
d9ad - Create valid ife decode action with drop control
219f - Create valid ife decode action with reclassify control
8f44 - Create valid ife decode action with jump control
b330 - Create ife encode action with cookie
Change 'matchPattern' values, allowing '0' and '0x0' if ife type is equal
to 0, and accepting both '0x' and '0X' otherwise, to let these tests pass
both with old and new tc binaries.
While at it, fix a small typo in test case fac3 ('maximnum'->'maximum').
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be 1 for normal allocations, 0 disables leak reporting.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Fixes: 85704cb8dc ("net/core/neighbour: tell kmemleak about hash tables")
Signed-off-by: David S. Miller <davem@davemloft.net>
The similar issue as fixed in Commit 4a2eb0c37b ("sctp: initialize
sin6_flowinfo for ipv6 addrs in sctp_inet6addr_event") also exists
in sctp_inetaddr_event, as Alexander noticed.
To fix it, allocate sctp_sockaddr_entry with kzalloc for both sctp
ipv4 and ipv6 addresses, as does in sctp_v4/6_copy_addrlist().
Reported-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reported-by: syzbot+ae0c70c0c2d40c51bb92@syzkaller.appspotmail.com
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said in draft-foschiano-erspan-03#section4:
Different frame variants known as "ERSPAN Types" can be
distinguished based on the GRE "Protocol Type" field value: Type I
and II's value is 0x88BE while Type III's is 0x22EB [ETYPES].
So set it properly in erspan_xmit() according to erspan_ver. While at
it, also remove the unused parameter 'proto' in erspan_fb_xmit().
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For nested and variable attributes, the expected length of an attribute
is not known and marked by a negative number. This results in an OOB
read when the expected length is later used to check if the attribute is
all zeros. Fix this by using the actual length of the attribute rather
than the expected length.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
New device of TRENDnet based on aqc111u
Add this ID to blacklist of cdc_ether driver as well
Signed-off-by: Dmitry Bezrukov <dmitry.bezrukov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Martin reported a set of filters don't work after changing
from reclassify to continue. Looking into the code, it
looks like skb protocol is not always fetched for each
iteration of the filters. But, as demonstrated by Martin,
TC actions could modify skb->protocol, for example act_vlan,
this means we have to refetch skb protocol in each iteration,
rather than using the one we fetch in the beginning of the loop.
This bug is _not_ introduced by commit 3b3ae88026
("net: sched: consolidate tc_classify{,_compat}"), technically,
if act_vlan is the only action that modifies skb protocol, then
it is commit c7e2b9689e ("sched: introduce vlan action") which
introduced this bug.
Reported-by: Martin Olsson <martin.olsson+netdev@sentorsecurity.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the referenced commit, Ethernet fails to come up at boot on the
board meson-gxl-s905x-libretech-cc. Fix this by re-enabling the
genphy_soft_reset callback for the Amlogic Meson GXL PHY driver.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Timotej Lazar <timotej.lazar@araneo.si>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 1c25324caf ("net/sched: act_tunnel_key: Don't dump dst port
if it wasn't set"), act_tunnel_key doesn't dump anymore the destination
port, unless it was explicitly configured. This caused systematic failures
in the following TDC test case:
7a88 - Add tunnel_key action with cookie parameter
Avoid matching zero values of TCA_TUNNEL_KEY_ENC_DST_PORT to let the test
pass again.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After merge of commit 80ef0f22ce ("net/sched: act_tunnel_key: Allow
key-less tunnels"), act_tunnel_key does not reject anymore requests to
install 'set' rules where the key id is missing. Therefore, drop the
following TDC testcase:
ba4e - Add tunnel_key set action with missing mandatory id parameter
because it's going to become a systematic fail as soon as userspace
iproute2 will start supporting key-less tunnels.
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
m88e1318_set_wol() takes the lock as part of phy_select_page(). Don't
take the lock again with phy_read(), use the unlocked __phy_read().
Fixes: 424ca4c551 ("net: phy: marvell: fix paged access races")
Reported-by: Åke Rehnman <ake.rehnman@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VOD can be out of spec, unless some magic value is poked into an
undocumented register in an undocumented page.
Fixes: e4cf8a38fc ("net: phy: Marvell: Add mv88e6390 internal PHY")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 65cab850f0 ("net: Allow class-e address assignment via ifconfig
ioctl") modified the IN_BADCLASS macro a bit, but unfortunatly one too
many '(' characters were added to the line, making any code that used
it, not build properly.
Also, the macro now compares an unsigned with a signed value, which
isn't ok, so fix that up by making both types match properly.
Reported-by: Christopher Ferris <cferris@google.com>
Fixes: 65cab850f0 ("net: Allow class-e address assignment via ifconfig ioctl")
Cc: Dave Taht <dave.taht@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP transmission with MSG_ZEROCOPY fails if the peer closes its end of
the connection and so transitions this socket to CLOSE_WAIT state.
Transmission in close wait state is acceptable. Other similar tests in
the stack (e.g., in FastOpen) accept both states. Relax this test, too.
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg276886.html
Link: https://www.mail-archive.com/netdev@vger.kernel.org/msg227390.html
Fixes: f214f915e7 ("tcp: enable MSG_ZEROCOPY")
Reported-by: Marek Majkowski <marek@cloudflare.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
CC: Yuchung Cheng <ycheng@google.com>
CC: Neal Cardwell <ncardwell@google.com>
CC: Soheil Hassas Yeganeh <soheil@google.com>
CC: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far genphy_soft_reset was used automatically if the PHY driver
didn't implement the soft_reset callback. This changed with the
mentioned commit and broke KSZ9031. To fix this configure the
KSZ9031 PHY driver to use genphy_soft_reset.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The changes introduced to allow rxrpc calls to be retried creates an issue
when it comes to refcounting afs_call structs. The problem is that when
rxrpc_send_data() queues the last packet for an asynchronous call, the
following sequence can occur:
(1) The notify_end_tx callback is invoked which causes the state in the
afs_call to be changed from AFS_CALL_CL_REQUESTING or
AFS_CALL_SV_REPLYING.
(2) afs_deliver_to_call() can then process event notifications from rxrpc
on the async_work queue.
(3) Delivery of events, such as an abort from the server, can cause the
afs_call state to be changed to AFS_CALL_COMPLETE on async_work.
(4) For an asynchronous call, afs_process_async_call() notes that the call
is complete and tried to clean up all the refs on async_work.
(5) rxrpc_send_data() might return the amount of data transferred
(success) or an error - which could in turn reflect a local error or a
received error.
Synchronising the clean up after rxrpc_kernel_send_data() returns an error
with the asynchronous cleanup is then tricky to get right.
Mostly revert commit c038a58ccf. The two API
functions the original commit added aren't currently used. This makes
rxrpc_kernel_send_data() always return successfully if it queued the data
it was given.
Note that this doesn't affect synchronous calls since their Rx notification
function merely pokes a wait queue and does not refcounting. The
asynchronous call notification function *has* to do refcounting and pass a
ref over the work item to avoid the need to sync the workqueue in call
cleanup.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ying Xue says:
====================
tipc: fix uninit-value issues reported by syzbot
Recently, syzbot complained that TIPC module exits several issues
associated with uninit-value type. So, in this series, we try to
fix them as many as possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
BUG: KMSAN: uninit-value in tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335
CPU: 0 PID: 4514 Comm: syz-executor485 Not tainted 4.16.0+ #87
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:17 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:53
kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
__msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683
tipc_nl_compat_doit+0x404/0xa10 net/tipc/netlink_compat.c:335
tipc_nl_compat_recv+0x164b/0x2700 net/tipc/netlink_compat.c:1153
genl_family_rcv_msg net/netlink/genetlink.c:599 [inline]
genl_rcv_msg+0x1686/0x1810 net/netlink/genetlink.c:624
netlink_rcv_skb+0x378/0x600 net/netlink/af_netlink.c:2447
genl_rcv+0x63/0x80 net/netlink/genetlink.c:635
netlink_unicast_kernel net/netlink/af_netlink.c:1311 [inline]
netlink_unicast+0x166b/0x1740 net/netlink/af_netlink.c:1337
netlink_sendmsg+0x1048/0x1310 net/netlink/af_netlink.c:1900
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg net/socket.c:640 [inline]
___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
__sys_sendmsg net/socket.c:2080 [inline]
SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091
SyS_sendmsg+0x54/0x80 net/socket.c:2087
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
RIP: 0033:0x43fda9
RSP: 002b:00007ffd0c184ba8 EFLAGS: 00000213 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000004002c8 RCX: 000000000043fda9
RDX: 0000000000000000 RSI: 0000000020023000 RDI: 0000000000000003
RBP: 00000000006ca018 R08: 00000000004002c8 R09: 00000000004002c8
R10: 00000000004002c8 R11: 0000000000000213 R12: 00000000004016d0
R13: 0000000000401760 R14: 0000000000000000 R15: 0000000000000000
Uninit was created at:
kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline]
kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188
kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314
kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321
slab_post_alloc_hook mm/slab.h:445 [inline]
slab_alloc_node mm/slub.c:2737 [inline]
__kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369
__kmalloc_reserve net/core/skbuff.c:138 [inline]
__alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206
alloc_skb include/linux/skbuff.h:984 [inline]
netlink_alloc_large_skb net/netlink/af_netlink.c:1183 [inline]
netlink_sendmsg+0x9a6/0x1310 net/netlink/af_netlink.c:1875
sock_sendmsg_nosec net/socket.c:630 [inline]
sock_sendmsg net/socket.c:640 [inline]
___sys_sendmsg+0xec0/0x1310 net/socket.c:2046
__sys_sendmsg net/socket.c:2080 [inline]
SYSC_sendmsg+0x2a3/0x3d0 net/socket.c:2091
SyS_sendmsg+0x54/0x80 net/socket.c:2087
do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287
entry_SYSCALL_64_after_hwframe+0x3d/0xa2
In tipc_nl_compat_recv(), when the len variable returned by
nlmsg_attrlen() is 0, the message is still treated as a valid one,
which is obviously unresonable. When len is zero, it means the
message not only doesn't contain any valid TLV payload, but also
TLV header is not included. Under this stituation, tlv_type field
in TLV header is still accessed in tipc_nl_compat_dumpit() or
tipc_nl_compat_doit(), but the field space is obviously illegal.
Of course, it is not initialized.
Reported-by: syzbot+bca0dc46634781f08b38@syzkaller.appspotmail.com
Reported-by: syzbot+6bdb590321a7ae40c1a6@syzkaller.appspotmail.com
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported:
BUG: KMSAN: uninit-value in tipc_conn_rcv_sub+0x184/0x950 net/tipc/topsrv.c:373
CPU: 0 PID: 66 Comm: kworker/u4:4 Not tainted 4.17.0-rc3+ #88
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: tipc_rcv tipc_conn_recv_work
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x185/0x1d0 lib/dump_stack.c:113
kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067
__msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683
tipc_conn_rcv_sub+0x184/0x950 net/tipc/topsrv.c:373
tipc_conn_rcv_from_sock net/tipc/topsrv.c:409 [inline]
tipc_conn_recv_work+0x3cd/0x560 net/tipc/topsrv.c:424
process_one_work+0x12c6/0x1f60 kernel/workqueue.c:2145
worker_thread+0x113c/0x24f0 kernel/workqueue.c:2279
kthread+0x539/0x720 kernel/kthread.c:239
ret_from_fork+0x35/0x40 arch/x86/entry/entry_64.S:412
Local variable description: ----s.i@tipc_conn_recv_work
Variable was created at:
tipc_conn_recv_work+0x65/0x560 net/tipc/topsrv.c:419
process_one_work+0x12c6/0x1f60 kernel/workqueue.c:2145
In tipc_conn_rcv_from_sock(), it always supposes the length of message
received from sock_recvmsg() is not smaller than the size of struct
tipc_subscr. However, this assumption is false. Especially when the
length of received message is shorter than struct tipc_subscr size,
we will end up touching uninitialized fields in tipc_conn_rcv_sub().
Reported-by: syzbot+8951a3065ee7fd6d6e23@syzkaller.appspotmail.com
Reported-by: syzbot+75e6e042c5bbf691fc82@syzkaller.appspotmail.com
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Toke Høiland-Jørgensen says:
====================
sched: Fix qdisc interactions exposed by using sch_cake as a leaf qdisc
This series fixes a couple of issues exposed by running sch_cake as a
leaf qdisc in an HFSC tree, which were discovered and reported by Pete
Heist. The interaction between CAKE's GSO splitting and the parent
qdisc's notion of its own queue length could cause queue stalls. While
investigating the report, I also noticed that several qdiscs would
dereference the skb pointer after dequeue, which is potentially
problematic since the GSO splitting code also frees the original skb.
See the individual patches in the series for details.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
To ensure parent qdiscs have the same notion of the number of enqueued
packets even after splitting a GSO packet, update the qdisc tree with the
number of packets that was added due to the split.
Reported-by: Pete Heist <pete@heistp.net>
Tested-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several qdiscs check on enqueue whether the packet was enqueued to a class
with an empty queue, in which case the class is activated. This is done by
checking if the qlen is exactly 1 after enqueue. However, if GSO splitting
is enabled in the child qdisc, a single packet can result in a qlen longer
than 1. This means the activation check fails, leading to a stalled queue.
Fix this by checking if the queue is empty *before* enqueue, and running
the activation logic if this was the case.
Reported-by: Pete Heist <pete@heistp.net>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parent qdiscs may dereference the pointer to the enqueued skb after
enqueue. However, both CAKE and TBF call consume_skb() on the original skb
when splitting GSO packets, leading to a potential use-after-free in the
parent. Fix this by avoiding dereferencing the skb pointer after enqueueing
to the child.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We forgot to update ip6erspan version related info when changing link,
which will cause setting new hwid failed.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 94d7d8f292 ("ip6_gre: add erspan v2 support")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding checks to detect wrong usage of the phylib API we added
a check to phy_start_aneg() which is too strict. If the phylib
state machine is in state PHY_HALTED we should allow reconfiguring
and restarting aneg, and just don't touch the state.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
