Warning(linux-2.6.21-git4//drivers/ata/libata-core.c:904): No description found for parameter 'new_sectors'
Warning(linux-2.6.21-git4//drivers/ata/libata-core.c:941): No description found for parameter 'new_sectors'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes some problems with ADMA-capable controllers with
regard to freeze, thaw and irq_clear libata callbacks. Freeze and
thaw didn't switch the ADMA-specific interrupts on or off, and more
critically the irq_clear function didn't respect the restriction that
the notifier clear registers for both ports have to be written at
the same time even when only one port is being cleared. This could
result in timeouts on one port when error handling (i.e. as a result
of hotplug) occurred on the other port.
As well, this fixes some issues in the interrupt handler: we shouldn't
check any ADMA status if the port has ADMA switched off because of
an ATAPI device, and it also checks to see if any ADMA interrupt has
been raised even when we are in port-register mode.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is a known problem with sata_promise on SATAII-150/300 TX4
controller cards: it enumerates drives in an order that differs
from the port numbers printed on the controller cards. However,
Promise's BIOS and Linux driver both get the order right.
I investigated Promise's Linux driver (v1.01.0.23), and found
that it explicitly changes the mapping from logical port number
to ATA engine MMIO address on the SATAII TX4 cards. It does this
on all SATAII TX4 cards, without inspecting revision etc. The
SATAII TX2plus cards continue to use the same mapping that was
used for the first-generation chips.
This patch updates sata_promise to use the new port number to
ATA engine mapping on SATAII TX4 cards, which fixes the drive
enumeration order problem on those cards. Tested on several
1st and 2nd generation TX2plus and TX4 chips.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sata_promise error decode update changed pdc_host_intr()
to return and not complete the qc after detecting an error.
Unfortunately not completing the qc:s causes them to always
time out on error, which is wrong and has nasty side-effects.
This patch updates pdc_error_intr() to call ata_port_abort(),
similar to ahci and sata_sil24. Doing this is important as it
makes EH see the original error and not a bogus timeout.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
_GTF command is never ATA_PROT_ATAPI_NODATA whether the device is
ATAPI or not. It's always ATA_PROT_NODATA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (25 commits)
sound: convert "sound" subdirectory to UTF-8
MAINTAINERS: Add cxacru website/mailing list
include files: convert "include" subdirectory to UTF-8
general: convert "kernel" subdirectory to UTF-8
documentation: convert the Documentation directory to UTF-8
Convert the toplevel files CREDITS and MAINTAINERS to UTF-8.
remove broken URLs from net drivers' output
Magic number prefix consistency change to Documentation/magic-number.txt
trivial: s/i_sem /i_mutex/
fix file specification in comments
drivers/base/platform.c: fix small typo in doc
misc doc and kconfig typos
Remove obsolete fat_cvf help text
Fix occurrences of "the the "
Fix minor typoes in kernel/module.c
Kconfig: Remove reference to external mqueue library
Kconfig: A couple of grammatical fixes in arch/i386/Kconfig
Correct comments in genrtc.c to refer to correct /proc file.
Fix more "deprecated" spellos.
Fix "deprecated" typoes.
...
Fix trivial comment conflict in kernel/relay.c.
flush_work(wq, work) doesn't need the first parameter, we can use cwq->wq
(this was possible from the very beginnig, I missed this). So we can unify
flush_work_keventd and flush_work.
Also, rename flush_work() to cancel_work_sync() and fix all callers.
Perhaps this is not the best name, but "flush_work" is really bad.
(akpm: this is why the earlier patches bypassed maintainers)
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Auke Kok <auke-jan.h.kok@intel.com>,
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(akpm: bypassed maintainers, sorry. There are other patches which depend on
this)
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add pata_platform device for RiscPC, thereby converting the primary
IDE channel on the machine to PATA.
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
libata previously depended upon waits in prereset to get resets after
hotplug right for both spin up and device ready wait. This was
necessary both for reliablity and speed as reset was likely to fail if
initiated too early and each try usually took more than 30secs to
fail. Previous patches fixed the reliability part by fixing status
and SCR handling in resets. This patch remedies the speed part by
improving reset sequencing.
Prereset waiting timeout is adjusted to 10s because spinup wait is
replaced by reset sequencing and !BSY wait is not as important as
before. During boot or module loading where the drive is already
fully spun up, !BSY wait succeeds immediately, so 10s should be enough
in most cases. It matters after hotplugging or other error
conditions, but in those cases, !BSY wait in prereset simply can't be
relied upon due to the varied and weird behaviors ATA controllers and
devices show.
Reset is now driven by ata_eh_reset_timeouts[] table which contains
timeouts for each reset try. The first reset can be softreset but the
following ones are always hardreset if available. Each timeout
defines deadline for the reset try. If a reset try fails, reset is
retried with the next timeout till the end of the timeout table is
reached. If a reset try fails before the timeout with error, libata
waits till the deadline of the failed try before retrying.
IOW, the timeout table defines timetable of reset tries such that the
n'th try always begins at least after the sum of all previous timeouts
has passed. The current timetable defines 4 tries and takes around 1
minute.
@0 : First try. This should succeed most of the time during boot.
@10 : 10s is enough to spin up most consumer harddrives. Give it
another shot.
@20 : 20s should spin up > 99% of working drives. This has 30s
timeout for retarded devices needing long idleness post reset.
@55 : Final try with 5s timeout just in case.
The above timetable is trade off between not annoying the device too
much with frequent resets and taking reasonable amount of time in most
cases. Some controllers may do better with shorter timeouts while
others may fare better with longer but we just can't rely upon LLD
writers to test each controller with wide variety of devices using
various scenarios. We need default behavior which reasonably fits
most cases.
I've tested the above timetable on a dozen SATA controllers and a few
PATA controllers with about a dozen different drives from all major
vendors and 4 different ODDs from three different vendors for both
boot and hotplug (if available) cases.
Boot probing is not affected unless the device is broken in which
cases new code gives up on the port after a minute rather than five or
nine minutes. When hotplugging, most devices get detected on the
first or second try. Multi-platter drives with long spin up time
which sometimes took > 40 secs with the original code, now usually
comes up during the second try and at least right after the third try
@20.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch updates ata_std_prereset() as follows.
* Don't fail on phy resume failure. Just whine and continue. Failure
from prereset makes libata abort whole reset sequence and give up
the port, so prereset() should be best effort. This is more
important with the coming EH updates as prereset() will be called
with shorter timeout.
* If ata_wait_ready() fails, whine and request hardreset instead.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For PATA, 0xff status indicates empty port. For SATA, it depends on
how the controller emulates status register. On some controllers,
0xff is used to represent broken link or certain stage during reset.
libata currently deals SATA the same. This hasn't caused any problem
because problematic situations usually only occur after hotplug or
other link disruption events and libata blindly waited for the device
to spin up and settle after hotplug giving the link and device
whatever time to go through those stages.
libata is going to replace unconditional spinup wait with generic
timed sequence of resets, so not only getting 0xff handling right for
SATA is, well, the right thing to do, it's much more important now.
This patch makes the following changes.
* Make ata_bus_softreset() return -ENODEV if any of its wait fails
due to 0xff status.
* Fail soft/hardreset if status wait returns -ENODEV indicating 0xff
status while SStatus says the link is online. e.g. Reset fails if
status is 0xff after reset when SStatus reports the linke is online.
If SCR registers are not available, everything is the same as
before.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add @deadline to prereset and reset methods and make them honor it.
ata_wait_ready() which directly takes @deadline is implemented to be
used as the wait function. This patch is in preparation for EH timing
improvements.
* ata_wait_ready() never does busy sleep. It's only used from EH and
no wait in EH is that urgent. This function also prints 'be
patient' message automatically after 5 secs of waiting if more than
3 secs is remaining till deadline.
* ata_bus_post_reset() now fails with error code if any of its wait
fails. This is important because earlier reset tries will have
shorter timeout than the spec requires. If a device fails to
respond before the short timeout, reset should be retried with
longer timeout rather than silently ignoring the device.
There are three behavior differences.
1. Timeout is applied to both devices at once, not separately. This
is more consistent with what the spec says.
2. When a device passes devchk but fails to become ready before
deadline. Previouly, post_reset would just succeed and let
device classification remove the device. New code fails the
reset thus causing reset retry. After a few times, EH will give
up disabling the port.
3. When slave device passes devchk but fails to become accessible
(TF-wise) after reset. Original code disables dev1 after 30s
timeout and continues as if the device doesn't exist, while the
patched code fails reset. When this happens, new code fails
reset on whole port rather than proceeding with only the primary
device.
If the failing device is suffering transient problems, new code
retries reset which is a better behavior. If the failing device is
actually broken, the net effect is identical to it, but not to the
other device sharing the channel. In the previous code, reset would
have succeeded after 30s thus detecting the working one. In the new
code, reset fails and whole port gets disabled. IMO, it's a
pathological case anyway (broken device sharing bus with working
one) and doesn't really matter.
* ata_bus_softreset() is changed to return error code from
ata_bus_post_reset(). It used to return 0 unconditionally.
* Spin up waiting is to be removed and not converted to honor
deadline.
* To be on the safe side, deadline is set to 40s for the time being.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Marvell IDE interface on my machine would hit a BUG_ON() in
lib/iomem.c because it was calling ata_pci_init_one() specifying just a
single port on the host, but that would actually end up trying to
initialize two ports, the second one with bogus information.
This fixes "ata_pci_init_one()" so that it actually passes down the
n_ports variable that it got from the low-level driver to the host
allocation routine ("ata_host_alloc_pinfo()"), which results in the ATA
layer actually having the correct port number information.
And in order to make it all work, I also needed to fix a few places that
had incorrectly hard-coded the fact that a host always had exactly two
ports (both ata_pci_init_bmdma() and ata_request_legacy_irqs() would
just always iterate over both ports).
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is grubby, but all the ata drivers do it this way.
Would it not be better to do
#define ata_scsi_device_resume NULL
in libata.h, remove all those ifdefs?
(updated version, ug, ug)
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Further HPT37x changes
- No 66MHz 370/370A
- Remove dead special case check now we use the DPLL (as per the IDE driver)
Pointed out by Sergei
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Yes its no longer 3x2n but 3xxn, I can rename it if you want Jeff
- Don't reset both ports each time (Sergei)
- If we can't get a DPLL then abort entirely
- Use ioport access for clock (from drivers/ide)
- Add HPT371N support (from drivers/ide)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/ata/libata-core.c: In function 'ata_hpa_resize':
drivers/ata/libata-core.c:986: warning: format '%lld' expects type 'long long int', but argument 5 has type 'u64'
drivers/ata/libata-core.c:986: warning: format '%lld' expects type 'long long int', but argument 6 has type 'u64'
drivers/ata/libata-core.c:990: warning: format '%lld' expects type 'long long int', but argument 4 has type 'u64'
drivers/ata/libata-core.c:990: warning: format '%lld' expects type 'long long int', but argument 5 has type 'u64'
drivers/ata/libata-core.c:1003: warning: format '%lld' expects type 'long long int', but argument 4 has type 'u64'
Also fix various 80-col bustage.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate ATA_EHI_DID_RESET into ATA_EHI_DID_SOFTRESET and
ATA_EHI_DID_HARDRESET. ATA_EHI_DID_RESET is redefined as OR of the
two flags. This patch doesn't introduce any behavior change. This
will be used later to determine whether _SDD is necessary or not.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Russell King hit a case where quantisation errors accumulated such that
the cycle time was shorter than rather than equal to the active/recovery
time. The code already knows how to stretch times to fit the cycle time
but does not know about the reverse.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
->cable_detect() used to be called on by the old ata_bus_probe() path.
Add invocation to ata_eh_revalidate_and_attach() right after IDENTIFYs
are done.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is added by added by cff63dfceb52c564fe1ba5394d50ab7d599a11b9
- pata: cable methods.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(S)ATA drives can be configured for "power-up in standby",
a mode whereby a specific "spin up now!" command is required
before the first media access.
Currently, a drive with this feature enabled can not be used at all
with libata, and once in this mode, the drive becomes a doorstop.
The older drivers/ide subsystem at least enumerates the drive,
so that it can be woken up after the fact from a userspace HDIO_*
command, but not libata.
This patch adds support to libata for the "power-up in standby"
mode where a "spin up now!" command (SET_FEATURES) is needed.
With this, libata will recognize such drives, spin them up,
and then re-IDENTIFY them if necessary to get a full/complete
set of drive features data.
Drives in this state are determined by looking for
special values in id[2], as documented in the current ATA specs.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Add support for ignoring the BIOS HPA result (off by default) and setting
the disk to the full available size unless already frozen.
Tested with various platforms/disks and confirmed to work with the
Macintosh (which broke earlier) and ata_piix (breakage due to the LBA48
readback that Tejun fixed).
For normal users this brings us, I believe, to feature parity with old IDE
(and of course more featured in some areas too).
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All drivers are converted to new init model. Kill probe_ent,
ata_device_add() and ata_pci_init_native_mode().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert pdc_adma, pata_cs5520, pata_isapnp, pata_ixp4xx_cf,
pata_legacy, pata_mpc52xx, pata_mpiix, pata_pcmcia, pata_pdc2027x,
pata_platform, pata_qdi, pata_scc and pata_winbond to new init model.
* init_one()'s now follow more consistent init order
* cs5520 now registers one host with two ports, not two hosts. If any
of the two ports are disabled, it's made dummy as other drivers do.
Tested pdc_adma and pata_legacy. Both are as broken as before. The
rest are compile tested only.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert ahci, sata_sil, sata_sil24, sata_svw, sata_qstor, sata_mv,
sata_sx4, sata_vsc and sata_inic162x to new init model.
Now that host and ap are available during intialization, functions are
converted to take either host or ap instead of low level parameters
which were inevitable for functions shared between init and other
paths. This simplifies code quite a bit.
* init_one()'s now follow more consistent init order
* ahci_setup_port() and ahci_host_init() collapsed into
ahci_init_one() for init order consistency
* sata_vsc uses port_info instead of setting fields manually
* in sata_svw, k2_board_info converted to port_info (info is now in
port flags). port number is honored now.
Tested on ICH7/8 AHCI, jmb360, sil3112, 3114, 3124 and 3132.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert drivers which use ata_pci_init_native_mode() to new init
model. ata_pci_init_native_host() is used instead. sata_nv, sata_uli
and sata_sis are in this category.
Tested on nVidia Corporation CK804 Serial ATA Controller [10de:0054]
in both BMDMA and ADMA mode.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert sata_via and sata_promise to new init model. Both controllers
can have combined configuration (SATA + PATA) and used twisted
initialization method (modifying port in ->port_start) to overcome
probe_ent limitations.
This patch converts both drivers to new init model in which such
configuration is natively supported.
* promise: Combined pata port now uses separate port_info entry right
after the sata counterpart entry.
* promise: Controller configuration is discerned using ap->flags.
This simplifies init path and makes it look more like other LLDs.
* via: Both SATA and PATA ports in vt6421 are represented in their
own port_info structure.
Tested on PDC20375 (SATA150 TX2plus) [105a:3375] and PDC40775 (SATA
300 TX2plus) [105a:3d73]. Couldn't test via cuz my c3 won't boot the
current kernel.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These will be used to convert LLDs to new init model.
* Add irq_handler field to port_info. In new init model, requesting
IRQ is LLD's responsibility and libata doesn't need to know about
irq_handler. Most LLDs can simply register their irq_handler but
some need different irq_handler depending on specific chip. The
added port_info->irq_handler field can be used by LLDs to select
the matching IRQ handler in such cases.
* Add ata_dummy_port_info.
* Implement ata_pci_prepare_native_host(), a helper to alloc ATA host,
acquire all resources and init the host in one go.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert native PCI host handling to alloc-init-register model. New
function ata_pci_init_native_host() follows the new init model and
replaces ata_pci_init_native_mode(). As there are remaining LLD
users, the old function isn't removed yet.
ata_pci_init_one() is reimplemented using the new function and now
fully converted to new init model.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert legacy PCI host handling to alloc-init-register model.
ata_init_legacy_host(), ata_request_legacy_irqs() and
ata_pci_init_bmdma() are separated out and follow the new init model.
The two legacy handling functions use separate ata_legacy_devres
instead of generic devm_* resources. This reduces devres overhead for
legacy hosts which was a bit high because it didn't use PCI/iomap
merged resoruces.
ata_pci_init_one() is rewritten in terms of the aboved functions but
native mode handling is still using the old method. Conversion will
be completed when native mode handling is updated.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ata_host_alloc_pinfo() and ata_host_register(). These helpers
will be used in the following patches to adopt new init model.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reorganize ata_host_alloc() and its subroutines into the following
three functions.
* ata_host_alloc() : allocates host and its ports. shost is not
registered automatically.
* ata_scsi_add_hosts() : allocates and adds shosts associated with an
ATA host. Used by ata_host_register().
* ata_host_register() : takes a fully initialized ata_host structure
and registers it to libata layer and probes it.
Only ata_host_alloc() and ata_host_register() are exported.
ata_device_add() is rewritten using the above functions. This patch
does not introduce any observable behavior change. Things worth
mentioning.
* print_id is assigned at registration time and LLDs are allowed to
overallocate ports and reduce host->n_ports during initialization.
ata_host_register() will throw away unused ports automatically.
* All SCSI host initialization stuff now resides in
ata_scsi_add_hosts() in libata-scsi.c, where it should be.
* ipr is now the only user of ata_host_init(). Either kill it by
converting ipr to use ata_host_alloc() and friends or rename and
move it to libata-scsi.c
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_host_start() from ata_device_add(). ata_host_start()
calls ->port_start on each port if available and freezes the port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't embed ap inside shost. Allocate it separately and point it back
from shosts's hostdata. This makes port allocation more flexible and
allows regular ATA and SAS share host alloc/init paths.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add PCI ID for new VIA chip. Original patch is from Maarten Vanraes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Maarten Vanraes <maarten.vanraes@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
