There are a few things that make the logging and
debugging in mac80211 less useful than it should
be right now:
* a lot of messages should be pr_info, not pr_debug
* wholesale use of pr_debug makes it require *both*
Kconfig and dynamic configuration
* there are still a lot of ifdefs
* the style is very inconsistent, sometimes the
sdata->name is printed in front
Clean up everything, introducing new macros and
separating out the station MLME debugging into
a new Kconfig symbol.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For better debugging, we would like to have
the sdata pointer available later, so pass
it into these functions.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The TKIP code hasn't been changed in a very long
time, so it seems unlikely that anyone really has
a need for the TKIP debug code. Remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Get current rssi (in dBm) from the driver/FW.
Instead of reporting the signal received in the last
rx packet, which might be inaccurate if rx traffic is
low and beacon filtering is enabled, get the signal
from the driver/FW.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a remain-on-channel item is deleted, we remove it
from the list and then start the next item. However,
if it wasn't actually the first item then calling
ieee80211_start_next_roc() is wrong as it will start
the first item -- even if that was already started.
Fix the two places that do this and add a warning to
prevent the problem from reoccurring.
Reported-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Set the necessary flags to allow user space applications
to register for authentication frames on IBSS interfaces.
This is useful for situations where userspace applications
want to control key negotiation between stations.
Signed-off-by: Will Hawkins <hawkinsw@opentechinstitute.org>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Check the auth frame registration count before sending
"open system" authentication messages when a new station
registers on a particular IBSS network. This stops us
from sending out multiple authentication messages with
different authentication algorithms.
Signed-off-by: Will Hawkins <hawkinsw@opentechinstitute.org>
[reword commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Track userspace registrations for authentication
frames received on an IBSS interface. This field
will be used to decide whether or not to send
"open system" authentication frames when a new
station joins an adhoc network.
Signed-off-by: Will Hawkins <hawkinsw@opentechinstitute.org>
[redesign the code flow a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case the driver suspend callback fails, mac80211 is left
with stopped queues which prevents any further traffic as well
as all STAs are left marked with WLAN_STA_BLOCK_BA which will
cause any further ADDBA requests to be declined. Fix it by
undoing both before returning from __iee80211_suspend.
Reported-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Save and configure the wmm_acm per sdata, rather than
per hardware.
If wmm_acm is saved per hardware when running two
interfaces simultaneously on the same hardware one
interface's wmm policy will be affected by the other
interface.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If an AP is beaconing with different capabilities than the one we get
in the associate response, we were still using the capabilities
received in the beacons. One example is when the AP is beaconing with
the short slot bit set to zero and then we try to connect to it with
long slot. In this case, we would keep using long slot until the next
beacon was received.
Fix this by using the correct capability value when calling
ieee80211_handle_bss_capability(). We were using cbss->capability,
but we should use the bss_conf->assoc_capability instead.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Commit "cfg80211: provide channel to start_ap function" assumes that the
channel is always passed to the NL80211_CMD_START_AP command, however
in case of multi-BSSID, hostapd only passes the channel for the first vif.
This makes starting beaconing on secondary vifs fail with -EINVAL.
Fix this by storing the channel provided to .start_ap in wdev->preset_chan
and picking the first AP vif's channel for secondary vifs if not provided.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To fix the testmode cross-namespace access problem,
use __cfg80211_rdev_from_attrs() to get the device
instead of open-coding similar functionality.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Change the function to __cfg80211_rdev_from_attrs
to take attributes instead of the info struct to
make it usable from dump callbacks for testmode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are currently a few ways to "escape"
the network namespace and access a wiphy
that belongs to another namespace. Add a
netns argument to the relevant functions
to fix this.
One remaining issue with testmode will be
fixed in a follow-up patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some compilers (eg. gcc 4.4.1 for ARM) report a false positive warning
in mlme.c:
net/mac80211/mlme.c: In function 'ieee80211_prep_connection':
net/mac80211/mlme.c:3035: warning: 'sta' may be used uninitialized in this function
This is a false positive because the place where 'sta' is used is
inside an if with the same condition of where it is set:
[...]
if (!have_sta) {
sta = sta_info_alloc(sdata, cbss->bssid, GFP_KERNEL);
if (!sta)
return -ENOMEM;
}
[...]
if (!have_sta) {
[...]
sta->sta.supp_rates[cbss->channel->band] = rates;
[...]
For some reason the compiler doesn't understand this and warns.
While this is not a problem in the code itself, we can avoid polluting
the build logs with false positives by setting sta to NULL on
declaration and checking for sta instead of !have_sta in the second if.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 'tell_ap' argument is always true. So that remove it
and simplify the function.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes the problem of dropping RANN element if the TTL
is 1. If the received RANN element TTL is 1 or greater than 1, the
RANN is processed. However, forwarding of received RANN element
with TTL 1 or less is prohibited according to the standard. This
is previously reported by Monthadar Al Jaberi.
Besides, this patch also avoid the processing of unicast PREQ
generation if the RANN element does not meet the acceptance
criteria mentioned in Sec. 13.10.12.4.2 of IEEE Std. 802.11-2012.
Reported-by: Monthadar Al Jaberi <monthadar@gmail.com>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some APs experience problems when working with U-APSD. Decrease the
probability of that happening by using legacy mode for all ACs but VO.
The AP that caused us troubles was a Cisco 4410N. It ignores our
setting, and always treats non-VO ACs as legacy.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While HW reconfig is in progress, drop all incoming Rx. This prevents
incoming packets from changing the internal state of the driver or
calling callbacks of the low level driver while it is in inconsistent
state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch fixes the wrong assignment of mesh element TTL.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As defined in section 13.10.9.3 Case D (802.11-2012), this
control variable is used to limit the mesh STA to send only
one PREQ to a root mesh STA within this interval of time
(in TUs). The default value for this variable is set to
2000 TUs. However, for current implementation, the maximum
configurable of dot11MeshHWMPconfirmationInterval is
restricted by dot11MeshHWMPactivePathTimeout.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
mesh_path_root_timer is invoked once the dot11MeshHWMPRootMode
is larger than 1. This patch also adds the backward compatible
to the previous setting on dot11MeshHWMPRootMode. If the user
configures as follow, it will still trigger the proactive RANN
with Gate Announcement.
iw mesh0 set mesh_param mesh_hwmp_rootmode 1
iw mesh0 set mesh_param mesh_gate_announcements 1
similar to the following setting:
iw mesh0 set mesh_param mesh_hwmp_rootmode 4
iw mesh0 set mesh_param mesh_gate_announcements 1
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generate the proactive PREP element in Proactive PREQ mode as
defined in Sec. 13.10.10.3 (Case D) of IEEE Std. 802.11-2012.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Generate the proactive PREQ element as defined in
Sec. 13.10.9.3 (Case C) of IEEE Std. 802.11-2012
based on the selection of dot11MeshHWMPRootMode as follow:
dot11MeshHWMPRootMode (2) is proactivePREQnoPREP
dot11MeshHWMPRootMode (3) is proactivePREQwithPREP
The proactive PREQ is generated based on the interval
defined by dot11MeshHWMProotInterval.
With this change, proactive RANN element is now generated
if the dot11MeshHWMPRootMode is set to (4) instead of (1).
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the mesh configuration parameters dot11MeshHWMProotInterval
and dot11MeshHWMPactivePathToRootTimeout to be used by
proactive PREQ mechanism.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
[line-break commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It should be NL80211_SCHED_SCAN_MATCH_ATTR_SSID as
documented, not NL80211_ATTR_SCHED_SCAN_MATCH_SSID.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If you add a monitor interface in parallel to a normal interface
mac80211 will let you to change the channel type on the monitor
interface even if you are connected. Add an explicit check to
disallow this.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
[fix typo in commit log, use sdata instead of netdev]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In my redesign of remain-on-channel I forgot
that an item could be cancelled when it's a
dependent item that is part of another item.
Allow cancelling such items by removing them
from the dependents list.
Note that when we cancel the main item, all
its dependents are also cancelled. It would
be possible to not do that, but would need
tricks to promote an item from dependent to
top-level and is tricky in the HW ROC case.
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ilan pointed out to me that ieee80211_start_next_roc()
already calls ieee80211_run_deferred_scan() if the list
of ROC items is empty, so there's no need to call it
again after calling ieee80211_start_next_roc().
Reported-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
fix the coding style related to mesh parameters, especially the indentation,
as pointed out by Johannes Berg.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Redesign all the off-channel code, getting rid of
the generic off-channel work concept, replacing
it with a simple remain-on-channel list.
This fixes a number of small issues with the ROC
implementation:
* offloaded remain-on-channel couldn't be queued,
now we can queue it as well, if needed
* in iwlwifi (the only user) offloaded ROC is
mutually exclusive with scanning, use the new
queue to handle that case -- I expect that it
will later depend on a HW flag
The bigger issue though is that there's a bad bug
in the current implementation: if we get a mgmt
TX request while HW roc is active, and this new
request has a wait time, we actually schedule a
software ROC instead since we can't guarantee the
existing offloaded ROC will still be that long.
To fix this, the queuing mechanism was needed.
The queuing mechanism for offloaded ROC isn't yet
optimal, ideally we should add API to have the HW
extend the ROC if needed. We could add that later
but for now use a software implementation.
Overall, this unifies the behaviour between the
offloaded and software-implemented case as much
as possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The IDLE handling in HW off-channel is broken right
now since we turn off IDLE only when the off-channel
period already started. Therefore, all drivers that
use it today (only iwlwifi!) must support off-channel
while idle, so playing with idle isn't needed at all.
Off-channel in general, since it's no longer used for
authentication/association, shouldn't affect PS, so
also remove that logic.
Also document a small caveat for reporting TX status
from off-channel frames in HW remain-on-channel.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When performing a HW restart for an AP mode interface, add stations back
only after the AP is beaconing. This mimics the normal flow of STA
addition on AP.
Some devices (wlcore) do not support adding stations before beaconing,
so this has the added benefit of making recovery work for them.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The remain-on-channel time validation shouldn't
depend on the value of HZ, as it does now with
the check against jiffies, since then you might
use a value that works on one system but not on
another. Fix it by checking against a minimum
that's fixed.
Also add validation of the wait duration for a
management frame TX since this also translates
into remain-on-channel internally.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drv_resume can get called without a prior call to drv_suspend.
Consider the following steps:
1. Suspend is started but driver's drv_suspend returns error.
2. Suspend is aborted. local->wowlan flag is left set.
3. Interface is removed.
4. Suspend again. This time open_count is 0 so drv_suspend is
not called and local->wowlan not cleared.
5. On resume ieee80211_reconfig will call drv_resume since
local->wowlan is set.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make mac80211 print a message when it disables
HT due to the connection using WEP/TKIP or due
to the AP not supporting WMM/QoS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For each EDCA TX queue change default settings (in STA mode) to conform
old 802.11b/g channel access rules. This is needed for drivers that do
not have QoS enable/disable "switch" (like rt2x00) to make them work
properly with legacy APs.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
__rfkill_switch_all() switches the state of devices of a given type; however,
it does not switch devices of all type (RFKILL_TYPE_ALL). As a result, it
ignores the keycode "KEY_RFKILL" from another module, i.e. eeepc-wmi.
This fix is to make __rfkill_switch_all() to be able to switch not only
devices of a given type but also all devices.
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we've removed all uses of the set_channel
API except for the monitor channel and in libertas,
clarify this. Split the libertas mesh use into a
new libertas_set_mesh_channel() operation, just to
keep backward compatibility, and rename the normal
set_channel() to set_monitor_channel().
Also describe the desired set_monitor_channel()
semantics more clearly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just like the AP mode patch, instead of setting
the channel and then joining the mesh network,
provide the channel to join the network on to
the join_mesh() function.
Like in AP mode, you can also give the channel
to the join-mesh nl80211 command now.
Unlike AP mode, it picks a default channel if
none was given.
As libertas uses mesh mode interfaces but has
no join_mesh callback and we can't simply break
it, keep some compatibility code for that case
and configure the channel directly for it.
In the non-libertas case, where we store the
channel until join, allow setting it while the
interface is down.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If it worked (Felix says it doesn't right now), the
typical use-case for WDS interfaces would be to be
slaved to AP mode interfaces. Therefore, it isn't
necessary to set the channel on WDS interfaces. As
they don't support powersave or anything like that,
they also couldn't use a different channel anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
