During a 'resync' or similar activity, md checks if the devices in the
array are otherwise active and winds back resync activity when they are.
This test in done in is_mddev_idle, and it is somewhat fragile - it
sometimes thinks there is non-sync io when there isn't.
The test compares the total sectors of io (disk_stat_read) with the sectors
of resync io (disk->sync_io). This has problems because total sectors gets
updated when a request completes, while resync io gets updated when the
request is submitted. The time difference can cause large differenced
between the two which do not actually imply non-resync activity. The test
currently allows for some fuzz (+/- 4096) but there are some cases when it
is not enough.
The test currently looks for any (non-fuzz) difference, either positive or
negative. This clearly is not needed. Any non-sync activity will cause
the total sectors to grow faster than the sync_io count (never slower) so
we only need to look for a positive differences.
If we do this then the amount of in-flight sync io will never cause the
appearance of non-sync IO. Once enough non-sync IO to worry about starts
happening, resync will be slowed down and the measurements will thus be
more precise (as there is less in-flight) and control of resync will still
be suitably responsive.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a raid1 has only one working drive, we want read error to propagate up
to the filesystem as there is no point failing the last drive in an array.
Currently the code perform this check is racy. If a write and a read a
both submitted to a device on a 2-drive raid1, and the write fails followed
by the read failing, the read will see that there is only one working drive
and will pass the failure up, even though the one working drive is actually
the *other* one.
So, tighten up the locking.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 5b479c91da.
Quoth Neil Brown:
"It causes an oops when auto-detecting raid arrays, and it doesn't
seem easy to fix.
The array may not be 'open' when do_md_run is called, so
bdev->bd_disk might be NULL, so bd_set_size can oops.
This whole approach of opening an md device before it has been
assembled just seems to get more and more painful. I think I'm going
to have to come up with something clever to provide both backward
comparability with usage expectation, and sane integration into the
rest of the kernel."
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
md currently uses ->media_changed to make sure rescan_partitions
is call on md array after they are assembled.
However that doesn't happen until the array is opened, which is later
than some people would like.
So use blkdev_ioctl to do the rescan immediately that the
array has been assembled.
This means we can remove all the ->change infrastructure as it was only used
to trigger a partition rescan.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"reshape_position" records how much progress has been made on a "reshape"
(adding drives, changing layout or chunksize).
When it is set, the number of drives, layout and chunksize can have
two possible values, an old an a new.
So allow these different values to be visible, and allow both old and new to
be set: Set the old ones first, then the reshape_position, then the new
values.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLUB doesn't like slashes as it wants to use the cache name as the name of a
directory (or symlink) in sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If CONFIG_NET is not selected, csum_partial is not exported, so md.ko cannot
use it. We shouldn't really be using csum_partial anyway as it is an
internal-to-networking interface.
So replace it with C code to do the same thing. Speed is not crucial here, so
something simple and correct is best.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need to check for internal-consistency of superblock in load_super.
validate_super is for inter-device consistency.
With the test in the wrong place, a badly created array will confuse md rather
an produce sensible errors.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We can save some lines of code by using seq_release_private().
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use ARRAY_SIZE macro already defined in kernel.h
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the possibility of having uninitialized log state if the
log device has failed.
When a mirror resumes operation, it calls 'resume' on the logging module. If
disk based logging is being used, the log device is read to fill in the log
state. If the log device has failed, we cannot simply return, because this
would leave the in-memory log state uninitialized. Instead, we assume all
regions are out-of-sync and reset the log state. Failure to do this could
result in the logging code reporting a region as in-sync, even though it
isn't; which could result in a corrupted mirror.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The call to rh_in_sync() in do_reads() should be allowed to block. It is in
the mirror worker thread which already permits blocking operations. This will
be needed to support clustered mirroring which will perform network
operations.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the code as it is, it is possible for oustanding clear region requests
never to get flushed when a mirror is deactivated or suspended. This means
there will always be some resync work required when a mirror is activated,
even though it may very well be in-sync.
Always requesting the flush doesn't hurt us. This is because the log tracks
whether any changes occurred and, if not, no flush is performed.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New device-mapper target that can delay I/O (for testing). Reads can be
separated from writes, redirected to different underlying devices and delayed
by differing amounts of time.
Signed-off-by: Heinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
More bio_list helper functions for new targets (including dm-delay and
dm-loop) to manipulate lists of bios.
Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Bryn Reeves <breeves@redhat.com>
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch ports dm-raid1.c to the new dm-io interface.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch ports dm-log.c to the new dm-io interface in order to make it
scalable to have a large number of persistent dirty logs active in parallel.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Cc: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch ports dm-exception-store.c to the new, scalable dm_io() interface.
It replaces dm_io_get()/dm_io_put() by
dm_io_client_create()/dm_io_client_destroy() calls and
dm_io_sync_vm() by dm_io() to achive this.
Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Cc: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new API to dm-io.c that uses a private mempool and bio_set for each
client.
The new functions to use are dm_io_client_create(), dm_io_client_destroy(),
dm_io_client_resize() and dm_io().
Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Milan Broz <mbroz@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce struct dm_io_client to prepare for per-client mempools and bio_sets.
Temporary functions bios() and io_pool() choose between the per-client
structures and the global ones so the old and new interfaces can co-exist.
Make error_bits optional.
Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Milan Broz <mbroz@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Delay decrementing the 'struct io' reference count until after the bio has
been freed so that a bio destructor function may reference it. Required by a
later patch.
Signed-off-by: Heinz Mauelshagen <hjm@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Milan Broz <mbroz@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the ability to specify desired features in the mirror
constructor/mapping table.
The first feature of interest is "handle_errors". Currently, mirroring will
ignore any I/O errors from the devices. Subsequent patches will check for
this flag and handle the errors. If flag/feature is not present, mirror will
do nothing - maintaining backwards compatibility.
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch reports the status of the log device so that userspace can detect
the error and take appropriate action.
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch gives the disk logging code the ability to store the fact that an
error occured on the log device. In addition, an event is raised when an
error is encountered during I/O to the log device.
Signed-off-by: Jonathan E Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow check_device_area to succeed if a device has an i_size of zero. This
addresses an issue seen on DASD devices setting up a multipath table for paths
in online and offline state.
Signed-off-by: Mike Anderson <andmike@us.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make the mapped device structure accessible to hardware handlers so error
messages can include the device name.
Signed-off-by: Edward Goggin <egoggin@emc.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a new IV generation method 'null' to read old filesystem images created
with SuSE's loop_fish2 module.
Signed-off-by: Ludwig Nussel <ludwig.nussel@suse.de>
Acked-By: Christophe Saout <christophe@saout.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allocate smaller clones
With the previous dm-crypt fixes, there is no need for the clone bios to have
the same bvec size as the original - we just need to make them big enough for
the remaining number of pages. The only requirement is that we clear the
"out" index in convert_context, so that crypt_convert starts storing data at
the right position within the clone bio.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get rid of first_clone in dm-crypt
This gets rid of first_clone, which is not really needed. Apparently, cloned
bios used to share their bvec some time way in the past - this is no longer
the case. Contrarily, this even hurts us if we try to create a clone off
first_clone after it has completed, and crypt_endio has destroyed its bvec.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do not access the bio after generic_make_request
We should never access a bio after generic_make_request - there's no guarantee
it still exists.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Call clone_init early
We need to call clone_init as early as possible - at least before call
bio_put(clone) in any error path. Otherwise, the destructor will try to
dereference bi_private, which may still be NULL.
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Disable barriers in dm-crypt because of current workqueue processing can
reorder requests.
This must be addresed later but for now disabling barriers is needed to
prevent data corruption.
Signed-off-by: Milan Broz <mbroz@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch replaces the single instance of kmirrord by one instance per mirror
set. This change is required to avoid a deadlock in kmirrord when the
persistent dirty log of a mirror itself resides on a mirror. The single
instance of kmirrord then issues a sync write to the dirty log in write_bits
which gets deferred to kmirrord itself later in the call chain. But kmirrord
never does the deferred work because it is still waiting for the sync
write_bits.
_mirror_sets is removed as it no longer needed, and we always flush the
workqueue before destroying it to ensure all work is complete before
destroying it.
Signed-off-by: Holger Smolinski <smolinski@de.ibm.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove do_sync_file_range() and convert callers to just use
do_sync_mapping_range().
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the destroy_dirty_buffers argument from invalidate_bdev(), it hasn't
been used in 6 years (so akpm says).
find * -name \*.[ch] | xargs grep -l invalidate_bdev |
while read file; do
quilt add $file;
sed -ie 's/invalidate_bdev(\([^,]*\),[^)]*)/invalidate_bdev(\1)/g' $file;
done
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we scale the mempool sizes depending on memory installed
in the machine, except for the bio pool itself which sits at a fixed
256 entry pre-allocation.
There's really no point in "optimizing" this OOM path, we just need
enough preallocated to make progress. A single unit is enough, lets
scale it down to 2 just to be on the safe side.
This patch saves ~150kb of pinned kernel memory on a 32-bit box.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
If 'num_pages' were ever 1 more than a multiple of 8 (32bit platforms)
or of 16 (64 bit platforms). filemap_attr would be allocated one
'unsigned long' shorter than required. We need a round-up in there.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A device can be removed from an md array via e.g.
echo remove > /sys/block/md3/md/dev-sde/state
This will try to remove the 'dev-sde' subtree which will deadlock
since
commit e7b0d26a86
With this patch we run the kobject_del via schedule_work so as to
avoid the deadlock.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... still not sure why we need this ....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If this mddev and queue got reused for another array that doesn't register a
congested_fn, this function would get called incorretly.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All that is missing the the function pointers in raid4_pers.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When iterating through an array, one must be careful to test one's index
variable rather than another similarly-named variable.
The loop will read off the end of conf->disks[] in the following
(pathological) case:
% dd bs=1 seek=840716287 if=/dev/zero of=d1 count=1
% for i in 2 3 4; do dd if=/dev/zero of=d$i bs=1k count=$(($i+150)); done
% ./vmlinux ubd0=root ubd1=d1 ubd2=d2 ubd3=d3 ubd4=d4
# mdadm -C /dev/md0 --level=linear --raid-devices=4 /dev/ubd[1234]
adding some printks, I saw this:
[42949374.960000] hash_spacing = 821120
[42949374.960000] cnt = 4
[42949374.960000] min_spacing = 801
[42949374.960000] j=0 size=820928 sz=820928
[42949374.960000] i=0 sz=820928 hash_spacing=820928
[42949374.960000] j=1 size=64 sz=64
[42949374.960000] j=2 size=64 sz=128
[42949374.960000] j=3 size=64 sz=192
[42949374.960000] j=4 size=1515870810 sz=1515871002
Cc: Gautham R Shenoy <ego@in.ibm.com>
Acked-by: Neil Brown <neilb@cse.unsw.edu.au>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent patch for raid6 reshape had a change missing that showed up in
subsequent review.
Many places in the raid5 code used "conf->raid_disks-1" to mean "number of
data disks". With raid6 that had to be changed to "conf->raid_disk -
conf->max_degraded" or similar. One place was missed.
This bug means that if a raid6 reshape were aborted in the middle the
recorded position would be wrong. On restart it would either fail (as the
position wasn't on an appropriate boundary) or would leave a section of the
array unreshaped, causing data corruption.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i.e. one or more drives can be added and the array will re-stripe
while on-line.
Most of the interesting work was already done for raid5. This just extends it
to raid6.
mdadm newer than 2.6 is needed for complete safety, however any version of
mdadm which support raid5 reshape will do a good enough job in almost all
cases (an 'echo repair > /sys/block/mdX/md/sync_action' is recommended after a
reshape that was aborted and had to be restarted with an such a version of
mdadm).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An error always aborts any resync/recovery/reshape on the understanding that
it will immediately be restarted if that still makes sense. However a reshape
currently doesn't get restarted. With this patch it does.
To avoid restarting when it is not possible to do work, we call into the
personality to check that a reshape is ok, and strengthen raid5_check_reshape
to fail if there are too many failed devices.
We also break some code out into a separate function: remove_and_add_spares as
the indent level for that code was getting crazy.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mddev and queue might be used for another array which does not set these,
so they need to be cleared.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
md tries to warn the user if they e.g. create a raid1 using two partitions of
the same device, as this does not provide true redundancy.
However it also warns if a raid0 is created like this, and there is nothing
wrong with that.
At the place where the warning is currently printer, we don't necessarily know
what level the array will be, so move the warning from the point where the
device is added to the point where the array is started.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use kernel_fpu_begin() and kernel_fpu_end()
- Use boot_cpu_has() for feature testing even in userspace
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
