Some devices need the height of the user to compute various
parameters. One of this devices is Freescale's MMA9553L
(http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf)
that needs the height of the user to compute the stride length which
is used further to determine distance, speed and activity type.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These changes are needed to support the functionality of a pedometer.
A pedometer has two basic functionalities: step counter and step detector.
The step counter needs to be enabled and then it will count the steps
in its hardware register. Whenever the application needs to check
the step count, it will read the step counter register. To support the
step counter a new channel type STEPS is added. Since the pedometer needs
to be enabled first so that the hardware can count and store the steps,
we need a specific ENABLE channel info mask.
The step detector will generate an interrupt each time a step is detected.
To support this functionality we add a new event type INSTANCE.
For more information on the Android requirements for step counter and step
detector see:
http://source.android.com/devices/sensors/composite_sensors.html#counter
and http://source.android.com/devices/sensors/composite_sensors.html#detector.
A device that has the pedometer functionality this interface needs to
support is Freescale's MMA9553L:
http://www.freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
For some events (e.g.: step detector) a direction does not make sense.
Add IIO_EV_DIR_NONE to be used with such events and generate sysfs event
attributes that do not contain direction.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This channel will be used for exposing information about
activity composite sensors. Activities supported so far:
* running
* jogging
* walking
* still
THRESHOLD event is used to signal a change in the activity
state.
We associate a confidence interval for each activity expressed
as a percentage from 0 to 100.
* 0, means the sensor IS NOT reporting that activity.
* 100, means the sensor IS reporting that activity.
Users of this interface have two possible means to gather
information about the ongoing activities.
1. Event based, via event file descriptor
* sensor may report an event when ENTERING an activity or LEAVING
an activity based on a threshold value.
* drivers will wake up applications waiting data on the event fd
2. Polling, by reading the sysfs associated attribute files:
* /sys/bus/iio/devices/iio:device0/in_activity_running_input
expressed as percentage confidence value from 0 to 100.
This will offer an interface for Android significant motion
composite sensor defined here:
http://source.android.com/devices/sensors/composite_sensors.html
Activities listed above are supported by Freescale's MMA9553 sensor:
http://freescale.com/files/sensors/doc/ref_manual/MMA9553LSWRM.pdf
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Minimal implementation for KMX61 6-axis accelerometer/magnetometer. It exports
raw accel/magn readings together with scale and sampling frequency.
Datasheet will be available at:
http://www.kionix.com/6-axis-accelerometer-magnetometer/kmx61
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Onda v975w tablet contains an accelerometer that's advertised over
ACPI as SMO8500. This device is however a KXCJ9 accelerometer as
can be seen in the Windows driver's INF file, and from the etching on
the chipset ("KXCJ9 41566 0414").
This patch also removes the attempt to get the IRQ for the "data ready"
signal, as it does not seem to be supported by this device on this
platform.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds a new driver for solteam opto JSA1212 proximity and
ambient light sensor.
Basic details of the chip can be found here.
http://www.solteamopto.com.tw/detail.php?ms=3&po_unit=2&pt_unit=29&p_unit=120
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New drivers / supported parts
* rockchip - rk3066-tsadc variant
* si7020 humidity and temperature sensor
* mcp320x - add mcp3001, mcp3002, mcp3004, mcp3008, mcp3201, mcp3202
* bmp280 pressure and temperature sensor
* Qualcomm SPMI PMIC current ADC driver
* Exynos_adc - support exynos7
New features
* vf610-adc - add temperature sensor support
* Documentation of current attributes, scaled pressure, offset and
scaled humidity, RGBC intensity gain factor and scale applied to
differential voltage channels.
* Bring iio_event_monitor up to date with newer modifiers.
* Add of_xlate function to allow for complex channel mappings from the
device tree.
* Add -g parameter to generic_buffer example to allow for devices with
directly fed (no trigger) buffers.
* Move exynos driver over to syscon for PMU register access.
Cleanups, fixes for new drivers
* lis3l02dq drop an unneeded else.
* st sensors - renam st_sensors to st_sensor_settings (for clarity)
* st sensors - drop an unused parameter from all the probe utility
functions.
* vf610 better error handling and tidy up.
* si7020 - cleanups following merge
* as3935 - drop some unnecessary semicolons.
* bmp280 - fix the pressure calculation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=BDOo
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.19a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new drivers, features and cleanups for IIO in the 3.19 cycle.
New drivers / supported parts
* rockchip - rk3066-tsadc variant
* si7020 humidity and temperature sensor
* mcp320x - add mcp3001, mcp3002, mcp3004, mcp3008, mcp3201, mcp3202
* bmp280 pressure and temperature sensor
* Qualcomm SPMI PMIC current ADC driver
* Exynos_adc - support exynos7
New features
* vf610-adc - add temperature sensor support
* Documentation of current attributes, scaled pressure, offset and
scaled humidity, RGBC intensity gain factor and scale applied to
differential voltage channels.
* Bring iio_event_monitor up to date with newer modifiers.
* Add of_xlate function to allow for complex channel mappings from the
device tree.
* Add -g parameter to generic_buffer example to allow for devices with
directly fed (no trigger) buffers.
* Move exynos driver over to syscon for PMU register access.
Cleanups, fixes for new drivers
* lis3l02dq drop an unneeded else.
* st sensors - renam st_sensors to st_sensor_settings (for clarity)
* st sensors - drop an unused parameter from all the probe utility
functions.
* vf610 better error handling and tidy up.
* si7020 - cleanups following merge
* as3935 - drop some unnecessary semicolons.
* bmp280 - fix the pressure calculation.
According to the datasheet and as defined in struct bmp280_comp_press, dig_p1 is
of type u16, while dig_p2 to dig_p9 are of type s16. In
bmp280_read_compensation_press(), values read from the device were treated as
the wrong type.
In bmp280_read_press() the fractional part of the measured pressure is
calculated wrong. A better way is to use *val for the raw pressure and *val2 for
the quotient and let the core do the proper conversion using IIO_VAL_FRACTIONAL.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Vlad Dogaru <vlad.dogaru@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ADC on exynos7 is quite similar to ADCv2. The differences are as
follows:
- exynos7-adc has 8 input channels (as against 10 in ADCv2).
- exynos7 does not include an ADC PHY control register.
- Some ADC_CON2 register bits being used in ADCv2 are listed as
reserved in exynos7-adc. This results in a different init_hw
function for exynos7.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch updates the IIO based ADC driver to use syscon and regmap
APIs to access and use PMU registers instead of remapping the PMU
registers in the driver.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
To: linux-iio@vger.kernel.org
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The current ADC is peripheral of Qualcomm SPMI PMIC chips. It has
16 bits resolution and register space inside PMIC accessible across
SPMI bus.
The driver registers itself through IIO interface.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In si7020_read_raw() the pointer to the i2c client was obtained as second level
pointer, although a simple pointer is appropriate.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When reading temperature or humidity values, a shift of two bits to the right
needs to be applied, and only for the humidity channel a mask of the lower
12 bits needs to be applied. This reduces code repetition.
During probe, i2c_set_clientdata() was used, although its counterpart was not,
so drop it.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When #iio-cells is greater than '0', the driver could provide
a custom of_xlate function that reads the *args* and returns
the appropriate index in registered IIO channels array.
Add simple translation function, suitable for the most 1:1
mapped channels in IIO chips, and use it when driver did not
provide custom implementation.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The proper way to divide two signed 64-bit values is to use div64_s64.
Signed-off-by: Vlad Dogaru <vlad.dogaru@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
* ad5933 - fix a null pointer dereference due to an old change that prevents
different channels being registered for the buffer and used for sysfs
interfaces.
* ad5933 - Drop a bonus _raw from attribute names.
* st-sensors - Makes sure the correct number of elements are copied when
filling a local buffer copy.
* mxs-lradc - Disable clocks in a failure path during probe so they aren't
left running.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TYUO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-3.18a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 3.18 cycle.
* ad5933 - fix a null pointer dereference due to an old change that prevents
different channels being registered for the buffer and used for sysfs
interfaces.
* ad5933 - Drop a bonus _raw from attribute names.
* st-sensors - Makes sure the correct number of elements are copied when
filling a local buffer copy.
* mxs-lradc - Disable clocks in a failure path during probe so they aren't
left running.
There is no need to pass a 'fake' return value when platform_get_irq() fails.
Propagate the real error instead.
While at it, only consider negative numbers returned by platform_get_irq()
as error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support to the Industrial IO subsystem
for the Silicon Labs Si7013/20/21 Relative Humidity and
Temperature Sensors.
Website: http://www.silabs.com/products/sensors/humidity-sensors/Pages/si7013-20-21.aspx
These are i2c devices which measure relative humidity
and temperature and all use the same protocol. The
Si7013 has an additional input with programmable
linearization which is not supported because that's
complicated and I didn't need it.
Signed-off-by: David Barksdale <dbarksdale@uplogix.com>
--
Changes since v1:
* Renamed to si7020 and replaced Si701x/2x with Si7013/20/21.
* Removed unneeded mutex.
* Pre-computed floating-point constant expressions.
* Removed address_list and I2C_CLASS_HWMON.
Changes since v2:
* Return correct raw sensor values.
* Rename dev variable to indio_dev.
* Issue a software reset command during probe.
* Un-broke string literal.
Changes since v3:
* enum changed to #define
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
No need to call the SIMPLE_DEV_PM_OPS() macro in several lines.
It can fit into the 80-column range.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If clk_prepare_enable() fails we should disable the regulator that was
previously enabled.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
There is no need to pass the error clock code to the variable 'ret'.
Just return the error directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use byte_for_channel as iterator to properly initialize the buffer.
Signed-off-by: Robin van der Gracht <robin@protonic.nl>
Acked-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Cc: <Stable@vger.kernel.org>
This patch fix pressure data variable name. Usually pdata name
it is used for platform data.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch change structure name and related variables names.
Signed-off-by: Denis Ciocca <denis.ciocca@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We want the fixes in there, and it resolves a merge issue with
drivers/iio/accel/bma180.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Older Rockchip SoCs, at least the rk3066, used a slightly modified saradc
for temperature measurements. This so called tsadc does not contain any
active parts like temperature interrupts and only supports polling the
current temperature. The returned voltage can then be converted by a
suitable thermal driver to and actual temperature and used for thermal
handling.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Vybrid ADC peripheral includes a temperature sensor
which is connected to channel number 26. This patch
adds support for the sensor. The raw value is read
and the temperature calculated in milli degree Celsius,
which is returned using IIO_CHAN_INFO_PROCESSED option.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
the BMA250 has only 10-bit resolution; while the data readout registers
have identical layout, the configuration is completely different compared
to the BMA180
datasheet: http://ae-bst.resource.bosch.com/media/products/dokumente/bma250/BST-BMA250-DS002-05.pdf
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
makes it easier to add more chip variants and removes redundancy:
scales and frequencies are now stated just once
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
move part of bma180_init() to bma180_config() (split initialization and
configuration code); configuration is heavily chip-specific
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
8-bit signed; 0 LSB @ 24 °C, 0.5 °C per LSB
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
and minor cleanups
Signed-off-by: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Oleksandr Kravchenko <o.v.kravchenko@globallogic.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for the BMI055 gyroscope sensor. BMI055 is a package
consisting of an acceleration sensor and a gyroscope. This patch
adds support for the gyroscope only.
Spec downloaded from:
http://ae-bst.resource.bosch.com/media/products/dokumente/bmi055/BST-BMI055-DS000-06.pdf
The BMI055 gyroscope uses the same register definition as BMG160,
but does not specify a temp register. However, the temp register
seems to be working in the same way as for BMG160, so this patch
does not remove the temp channel for BMI055.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Noticed when compiling with CONFIG_PM_RUNTIME not set:
kxcjk-1013.c: warning: ‘kxcjk1013_get_startup_times’ defined but not used [-Wunused-function]
Introduced by commit 124e1b1d (iio: accel: kxcjk-1013: support runtime pm).
Signed-off-by: Daniel Baluta <daniel.baluta@intel.com>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
