* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
mach-ux500: configure board for the TPS61052 regulator v2
mach-ux500: provide ab8500 init vector
mach-ux500: board support for AB8500 GPIO driver
gpio: driver for 42 AB8500 GPIO pins
* 'for-linus' of git://gitserver.sunplusct.com/linux-2.6-score:
score: Use generic show_interrupts()
score: Convert to new irq function names
score: lost a semicolon in asm/irqflags.h
score: Select GENERIC_HARDIRQS_NO_DEPRECATED
score: Convert irq_chip to new functions
The acpi video driver attempts to explicitly create a sysfs link between
the acpi device and the associated PCI device. However, we're now also
doing this from the backlight core, which means that we get a backtrace
caused by a duplicate file. Remove the code and leave it up to the
backlight core.
Reported-by: Jeff Chua <jeff.chua.linux@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Tested-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a hole spans across page boundaries, the next write forces
a read of the block. This could end up reading existing garbage
data from the disk in ocfs2_map_page_blocks. This leads to
non-zero holes. In order to avoid this, mark the writes as new
when the holes span across page boundaries.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
Signed-off-by: jlbec <jlbec@evilplan.org>
When CONFIG_DEBUG_FS=y and CONFIG_OCFS2_FS_STATS=n, we get the
following warning:
fs/ocfs2/cluster/tcp.c:213:16: warning: ‘o2net_get_func_run_time’
defined but not used
Since o2net_get_func_run_time is only called from
o2net_update_recv_stats, so move it under CONFIG_OCFS2_FS_STATS.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: jlbec <jlbec@evilplan.org>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
NFS: Ensure that rpc_release_resources_task() can be called twice.
NFS: Don't leak RPC clients in NFSv4 secinfo negotiation
NFS: Fix a hang in the writeback path
Stephen ran into the following build error:
drivers/mfd/cs5535-mfd.c:30:22: error: asm/olpc.h: No such file or directory
olpc.h exists only on x86 (and in the future, ARM). Rather than
wrapping the include in an #ifdef, just change cs5535-mfd to only build
on x86.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 95a0f10cdd ("drbd: store in-core bitmap little endian,
regardless of architecture") drbd had made the sane choice to use
little-endian bitmap functions everywhere. However, it used the
horrible old functions names from <asm-generic/bitops/le.h>, that were
never really meant to be exported.
In the meantime, things got cleaned up, and in commit c4945b9ed4
("asm-generic: rename generic little-endian bitops functions") we
renamed the LE bitops to something sane, exactly so that they could be
used in random code without people gouging their eyes out when seeing
the crazy jumble of letters that were the old internal names.
As a result the drbd thing merged cleanly (commit 8d49a77568: "Merge
branch 'for-2.6.39/drivers' of git://git.kernel.dk/linux-2.6-block"),
since there was no data conflict - but the end result obviously doesn't
actually compile.
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current mainline codes of ARCH_S5P64X0 and ARCH_S5P6442
can not support suspend to ram. So needs this for preventing
build error on them.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes CPU idmask of S5P64X0 and EXYNOS4210
and its comparison method because just want to use CPU
id for it.
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Fix incorrect conditional execution of ldr instructions in
addruart macro.
Signed-off-by: Thomas Abraham <thomas.abraham@samsung.com>
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes smsc9215 irq ploarity configuration of SMDKC210.
We can change type of EINT(5) as HIGH, but it's better to change
IRQ output of smsc9215 as an active low because smsc's IRQ line
has been pull-up.
Signed-off-by: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes smsc9215 irq ploarity configuration of SMDKV310.
We can change type of EINT(5) as HIGH, but it's better to change
IRQ output of smsc9215 as an active low because smsc's IRQ line
has been pull-up.
Signed-off-by: Jeongtae Park <jtp.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes following build warnings.
warning: (MACH_ARMLEX4210) selects SATA_AHCI_PLATFORM
which has unmet direct dependencies (ATA)
And adds EXYNOX4_DEV_AHCI for building machines which are
not suppoort for AHCI feature on board.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This change is intended to correct security subsystem interrupt names
for Samsung S5PV210 and S5PC110 SoCs.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The array size parameter of iotable_init for S5P6450 is incorrect.
Fix this by passing the correct length of s5p6450_iodesc table.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This registers the TPS61052 regulator to the ux500 MOP/HREF boards.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds an ab8500 regulator initialization vector for the
HREF/MOP500 series of boards. This also sets the display
regulator to be on at boot so we don't loose our splash
screen when the board comes up.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is the board support patch for ab8500 gpio driver
on mach-ux500.Patch implements 16 virtual
IRQ mapped to 16 interrupt capable AB8500 GPIOs.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
[Modify for header file placement]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To get rid of port expanders, the free GPIOs of ab8500
can be used. There are 42 GPIO pins. Out of which 16
are interrupt capable.This patch implements 16 virtual
IRQ mapped to 16 interrupt capable AB8500 GPIOs.
Signed-off-by: Bibek Basu <bibek.basu@stericsson.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[Renamed header file as per MFD structure]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the proper accessor functions in show_interrupts() while at it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Chen Liqin <liqin.chen@sunplusct.com>
* 'irq-cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tile: Use generic show_interupts()
tile: Convert to new irq function names
dma: Ipu: Convert interupt code
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator: Add MODULE_DEVICE_TABLE to max8997 and max8998
regulator: fix tps6524x section mismatch
regulator: Remove more wm831x-specific IRQ operations
regulator: add ab8500 enable and raise time delays
regulator: provide consumer interface for fall/rise time
regulator: add set_voltage_time_sel infrastructure
regulator: initialization for ab8500 regulators
regulator: add support for USB voltage regulator
regulator: switch the ab3100 to use enable_time()
Regulator: add suspend-finish API for regulator core.
regulator: fix typo in Kconfig
regulator: Convert WM831x regulators to genirq
regulator: If we fail when setting up a supply say which supply
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: Fix yet another race in disconnection
ALSA: asihpi - Update verbose debug print macros
ALSA: asihpi - Improve non-busmaster adapter operation
ALSA: asihpi - Support single-rate no-SRC cards
ALSA: HDA: New AD1984A model for Dell Precision R5500
ALSA: vmalloc buffers should use normal mmap
ALSA: hda - Fix SPDIF out regression on ALC889
ALSA: usb-audio - Support for Boss JS-8 Jam Station
ALSA: usb-audio: add Cakewalk UM-1G support
sound/oss/opl3: validate voice and channel indexes
sound/oss: remove offset from load_patch callbacks
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
staging: Fix bdops->check_events() misconversion in cyasblkdev_block.c
ide: ensure that we re-run the queue handler
* 'for-2.6.39/drivers' of git://git.kernel.dk/linux-2.6-block: (122 commits)
cciss: fix lost command issue
drbd: need include for bitops functions declarations
Revert "cciss: Add missing allocation in scsi_cmd_stack_setup and corresponding deallocation"
cciss: fix missed command status value CMD_UNABORTABLE
cciss: remove unnecessary casts
cciss: Mask off error bits of c->busaddr in cmd_special_free when calling pci_free_consistent
cciss: Inform controller we are using 32-bit tags.
cciss: hoist tag masking out of loop
cciss: Add missing allocation in scsi_cmd_stack_setup and corresponding deallocation
cciss: export resettable host attribute
drbd: drop code present under #ifdef which is relevant to 2.6.28 and below
drbd: Fixed handling of read errors on a 'VerifyS' node
drbd: Fixed handling of read errors on a 'VerifyT' node
drbd: Implemented real timeout checking for request processing time
drbd: Remove unused function atodb_endio()
drbd: improve log message if received sector offset exceeds local capacity
drbd: kill dead code
drbd: don't BUG_ON, if bio_add_page of a single page to an empty bio fails
drbd: Removed left over, now wrong comments
drbd: serialize admin requests for new verify run with pending bitmap io
...
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
hwmon: (f71882fg) Add support for the F71889A
hwmon: (f71882fg) Add support for the F81865F
hwmon: (f71882fg) Document all supported devices
hwmon: (f71882fg) Per-chip fan/temperature input count tables
hwmon: (f71882fg) Secure chip property definition arrays
I no longer have access to any hardware that uses APM and have not
provided real maintenance for several years. Hopefully someone with the
hardware or energy will step forward if the driver is to be kept.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix fsl_rio.c kernel-doc warning: no exported symbols as
requested by !E are found:
Warning(arch/powerpc/sysdev/fsl_rio.c): no structured comments found
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
DocBook/v4l/ no longer has any *.png files, so the 'cp' command fails,
breaking the build. Drop the *.png cp.
cp: cannot stat `linux-2.6.38-git18/Documentation/DocBook/v4l/*.png': No such file or directory
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix inode.c kernel-doc fatal error: 2 comment sections have the same name:
Error(fs/inode.c:1171): duplicate section name 'Note'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix ipc/util.c kernel-doc warnings:
Warning(ipc/util.c:336): No description found for parameter 'ns'
Warning(ipc/util.c:620): No description found for parameter 'ns'
Warning(ipc/util.c:790): No description found for parameter 'ns'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Reviewed-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix mm/memory.c incorrect kernel-doc function notation:
Warning(mm/memory.c:3718): Cannot understand * @access_remote_vm - access another process' address space
on line 3718 - I thought it was a doc line
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Omit the segment prefix in the UP case. GS is not used then
and we will generate segfaults if cmpxchg16b is used otherwise.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When m_start returns an error, the seq_file logic will still call m_stop
with that error entry, so we'd better make sure that we check it before
using it as a vma.
Introduced by commit ec6fd8a435 ("report errors in /proc/*/*map*
sanely"), which replaced NULL with various ERR_PTR() cases.
(On ia64, you happen to get a unaligned fault instead of a page fault,
since the address used is generally some random error code like -EPERM)
Reported-by: Anca Emanuel <anca.emanuel@gmail.com>
Reported-by: Tony Luck <tony.luck@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Américo Wang <xiyou.wangcong@gmail.com>
Cc: Stephen Wilson <wilsons@start.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
