When finding the socket to report an error on, if the invoking packet
is using Segment Routing, the IPv6 destination address is that of an
intermediate router, not the end destination. Extract the ultimate
destination address from the segment address.
This change allows traceroute to function in the presence of Segment
Routing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC8754 says:
ICMP error packets generated within the SR domain are sent to source
nodes within the SR domain. The invoking packet in the ICMP error
message may contain an SRH. Since the destination address of a packet
with an SRH changes as each segment is processed, it may not be the
destination used by the socket or application that generated the
invoking packet.
For the source of an invoking packet to process the ICMP error
message, the ultimate destination address of the IPv6 header may be
required. The following logic is used to determine the destination
address for use by protocol-error handlers.
* Walk all extension headers of the invoking IPv6 packet to the
routing extension header preceding the upper-layer header.
- If routing header is type 4 Segment Routing Header (SRH)
o The SID at Segment List[0] may be used as the destination
address of the invoking packet.
Mangle the skb so the network header points to the invoking packet
inside the ICMP packet. The seg6 helpers can then be used on the skb
to find any segment routing headers. If found, mark this fact in the
IPv6 control block of the skb, and store the offset into the packet of
the SRH. Then restore the skb back to its old state.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An ICMP error message can contain in its message body part of an IPv6
packet which invoked the error. Such a packet might contain a segment
router header. Export get_srh() so the ICMP code can make use of it.
Since his changes the scope of the function from local to global, add
the seg6_ prefix to keep the namespace clean. And move it into seg6.c
so it is always available, not just when IPV6_SEG6_LWTUNNEL is
enabled.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Nicolas noted, if gateway validation fails walking the multipath
attribute the code should jump to the cleanup to free previously
allocated memory.
Fixes: 1ff15a710a ("ipv6: Check attribute length for RTA_GATEWAY when deleting multipath route")
Signed-off-by: David Ahern <dsahern@kernel.org>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220103170555.94638-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ip6_route_multipath_del loop continues processing the multipath
attribute even if delete of a nexthop path fails. For consistency,
do the same if the gateway attribute is invalid.
Fixes: 1ff15a710a ("ipv6: Check attribute length for RTA_GATEWAY when deleting multipath route")
Signed-off-by: David Ahern <dsahern@kernel.org>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Link: https://lore.kernel.org/r/20220103171911.94739-1-dsahern@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
v3:
- Report 'backlog' (bytes) instead of 'qlen' (number of packets)
v2:
- Fix sparse warning (use rcu_dereference)
This patch adds support for the queue depth in IOAM trace data fields.
The draft [1] says the following:
The "queue depth" field is a 4-octet unsigned integer field. This
field indicates the current length of the egress interface queue of
the interface from where the packet is forwarded out. The queue
depth is expressed as the current amount of memory buffers used by
the queue (a packet could consume one or more memory buffers,
depending on its size).
An existing function (i.e., qdisc_qstats_qlen_backlog) is used to
retrieve the current queue length without reinventing the wheel.
Note: it was tested and qlen is increasing when an artificial delay is
added on the egress with tc.
[1] https://datatracker.ietf.org/doc/html/draft-ietf-ippm-ioam-data#section-5.4.2.7
Signed-off-by: Justin Iurman <justin.iurman@uliege.be>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2021-12-30
The following pull-request contains BPF updates for your *net-next* tree.
We've added 72 non-merge commits during the last 20 day(s) which contain
a total of 223 files changed, 3510 insertions(+), 1591 deletions(-).
The main changes are:
1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii.
2) Beautify and de-verbose verifier logs, from Christy.
3) Composable verifier types, from Hao.
4) bpf_strncmp helper, from Hou.
5) bpf.h header dependency cleanup, from Jakub.
6) get_func_[arg|ret|arg_cnt] helpers, from Jiri.
7) Sleepable local storage, from KP.
8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
lwtunnel_valid_encap_type_attr is used to validate encap attributes
within a multipath route. Add length validation checking to the type.
lwtunnel_valid_encap_type_attr is called converting attributes to
fib{6,}_config struct which means it is used before fib_get_nhs,
ip6_route_multipath_add, and ip6_route_multipath_del - other
locations that use rtnh_ok and then nla_get_u16 on RTA_ENCAP_TYPE
attribute.
Fixes: 9ed59592e3 ("lwtunnel: fix autoload of lwt modules")
Signed-off-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure RTA_GATEWAY for IPv6 multipath route has enough bytes to hold
an IPv6 address.
Fixes: 6b9ea5a64e ("ipv6: fix multipath route replace error recovery")
Signed-off-by: David Ahern <dsahern@kernel.org>
Cc: Roopa Prabhu <roopa@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit referenced in the Fixes tag used nla_memcpy for RTA_GATEWAY as
does the current nla_get_in6_addr. nla_memcpy protects against accessing
memory greater than what is in the attribute, but there is no check
requiring the attribute to have an IPv6 address. Add it.
Fixes: 51ebd31815 ("ipv6: add support of equal cost multipath (ECMP)")
Signed-off-by: David Ahern <dsahern@kernel.org>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a check that the user-provided option is at least as long as the
number of bytes we intend to read. Before this patch we would blindly
read sizeof(int) bytes even in cases where the user passed
optlen<sizeof(int), which would potentially read garbage or fault.
Discovered by new tests in https://github.com/google/gvisor/pull/6957 .
The original get_user call predates history in the git repo.
Signed-off-by: Tamir Duberstein <tamird@gmail.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211229200947.2862255-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sock.h is pretty heavily used (5k objects rebuilt on x86 after
it's touched). We can drop the include of filter.h from it and
add a forward declaration of struct sk_filter instead.
This decreases the number of rebuilt objects when bpf.h
is touched from ~5k to ~1k.
There's a lot of missing includes this was masking. Primarily
in networking tho, this time.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Acked-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/bpf/20211229004913.513372-1-kuba@kernel.org
The "__ip6_tnl_parm" struct was left uninitialized causing an invalid
load of random data when the "__ip6_tnl_parm" struct was used elsewhere.
As an example, in the function "ip6_tnl_xmit_ctl()", it tries to access
the "collect_md" member. With "__ip6_tnl_parm" being uninitialized and
containing random data, the UBSAN detected that "collect_md" held a
non-boolean value.
The UBSAN issue is as follows:
===============================================================
UBSAN: invalid-load in net/ipv6/ip6_tunnel.c:1025:14
load of value 30 is not a valid value for type '_Bool'
CPU: 1 PID: 228 Comm: kworker/1:3 Not tainted 5.16.0-rc4+ #8
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
Workqueue: ipv6_addrconf addrconf_dad_work
Call Trace:
<TASK>
dump_stack_lvl+0x44/0x57
ubsan_epilogue+0x5/0x40
__ubsan_handle_load_invalid_value+0x66/0x70
? __cpuhp_setup_state+0x1d3/0x210
ip6_tnl_xmit_ctl.cold.52+0x2c/0x6f [ip6_tunnel]
vti6_tnl_xmit+0x79c/0x1e96 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? vti6_rcv+0x100/0x100 [ip6_vti]
? lock_is_held_type+0xd9/0x130
? rcu_read_lock_bh_held+0xc0/0xc0
? lock_acquired+0x262/0xb10
dev_hard_start_xmit+0x1e6/0x820
__dev_queue_xmit+0x2079/0x3340
? mark_lock.part.52+0xf7/0x1050
? netdev_core_pick_tx+0x290/0x290
? kvm_clock_read+0x14/0x30
? kvm_sched_clock_read+0x5/0x10
? sched_clock_cpu+0x15/0x200
? find_held_lock+0x3a/0x1c0
? lock_release+0x42f/0xc90
? lock_downgrade+0x6b0/0x6b0
? mark_held_locks+0xb7/0x120
? neigh_connected_output+0x31f/0x470
? lockdep_hardirqs_on+0x79/0x100
? neigh_connected_output+0x31f/0x470
? ip6_finish_output2+0x9b0/0x1d90
? rcu_read_lock_bh_held+0x62/0xc0
? ip6_finish_output2+0x9b0/0x1d90
ip6_finish_output2+0x9b0/0x1d90
? ip6_append_data+0x330/0x330
? ip6_mtu+0x166/0x370
? __ip6_finish_output+0x1ad/0xfb0
? nf_hook_slow+0xa6/0x170
ip6_output+0x1fb/0x710
? nf_hook.constprop.32+0x317/0x430
? ip6_finish_output+0x180/0x180
? __ip6_finish_output+0xfb0/0xfb0
? lock_is_held_type+0xd9/0x130
ndisc_send_skb+0xb33/0x1590
? __sk_mem_raise_allocated+0x11cf/0x1560
? dst_output+0x4a0/0x4a0
? ndisc_send_rs+0x432/0x610
addrconf_dad_completed+0x30c/0xbb0
? addrconf_rs_timer+0x650/0x650
? addrconf_dad_work+0x73c/0x10e0
addrconf_dad_work+0x73c/0x10e0
? addrconf_dad_completed+0xbb0/0xbb0
? rcu_read_lock_sched_held+0xaf/0xe0
? rcu_read_lock_bh_held+0xc0/0xc0
process_one_work+0x97b/0x1740
? pwq_dec_nr_in_flight+0x270/0x270
worker_thread+0x87/0xbf0
? process_one_work+0x1740/0x1740
kthread+0x3ac/0x490
? set_kthread_struct+0x100/0x100
ret_from_fork+0x22/0x30
</TASK>
===============================================================
The solution is to initialize "__ip6_tnl_parm" struct to zeros in the
"vti6_siocdevprivate()" function.
Signed-off-by: William Zhao <wizhao@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The max number of UDP gso segments is intended to cap to
UDP_MAX_SEGMENTS, this is checked in udp_send_skb().
skb->len contains network and transport header len here, we should use
only data len instead.
This is the ipv6 counterpart to the below referenced commit,
which missed the ipv6 change
Fixes: 158390e456 ("udp: using datalen to cap max gso segments")
Signed-off-by: Coco Li <lixiaoyan@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20211223222441.2975883-1-lixiaoyan@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We're about to break the cgroup-defs.h -> bpf-cgroup.h dependency,
make sure those who actually need more than the definition of
struct cgroup_bpf include bpf-cgroup.h explicitly.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Link: https://lore.kernel.org/bpf/20211216025538.1649516-3-kuba@kernel.org
The attributes are identical in all implementations so move the ipv4 one
into the core and remove the per-family nla policies.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
xfrm4_fill_dst() and xfrm6_fill_dst() build dst,
getting a device reference that will likely be released
by standard dst_release() code.
We have to track these references or risk a warning if
CONFIG_NET_DEV_REFCNT_TRACKER=y
Note to XFRM maintainers :
Error path in xfrm6_fill_dst() releases the reference,
but does not clear xdst->u.dst.dev, so I wonder
if this could lead to double dev_put() in some cases,
where a dst_release() _is_ called by the callers in their
error path.
This extra dev_put() was added in commit 84c4a9dfbf ("xfrm6:
release dev before returning error")
Fixes: 9038c32000 ("net: dst: add net device refcount tracking to dst_entry")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Cong Wang <amwang@redhat.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Link: https://lore.kernel.org/r/20211207193203.2706158-1-eric.dumazet@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When an IPv4 packet is received, the ip_rcv_core(...) sets the receiving
interface index into the IPv4 socket control block (v5.16-rc4,
net/ipv4/ip_input.c line 510):
IPCB(skb)->iif = skb->skb_iif;
If that IPv4 packet is meant to be encapsulated in an outer IPv6+SRH
header, the seg6_do_srh_encap(...) performs the required encapsulation.
In this case, the seg6_do_srh_encap function clears the IPv6 socket control
block (v5.16-rc4 net/ipv6/seg6_iptunnel.c line 163):
memset(IP6CB(skb), 0, sizeof(*IP6CB(skb)));
The memset(...) was introduced in commit ef489749aa ("ipv6: sr: clear
IP6CB(skb) on SRH ip4ip6 encapsulation") a long time ago (2019-01-29).
Since the IPv6 socket control block and the IPv4 socket control block share
the same memory area (skb->cb), the receiving interface index info is lost
(IP6CB(skb)->iif is set to zero).
As a side effect, that condition triggers a NULL pointer dereference if
commit 0857d6f8c7 ("ipv6: When forwarding count rx stats on the orig
netdev") is applied.
To fix that issue, we set the IP6CB(skb)->iif with the index of the
receiving interface once again.
Fixes: ef489749aa ("ipv6: sr: clear IP6CB(skb) on SRH ip4ip6 encapsulation")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211208195409.12169-1-andrea.mayer@uniroma2.it
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Note that other ip_tunnel users do not seem to hold a reference
on tunnel->dev. Probably needs some investigations.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We want to track all dev_hold()/dev_put() to ease leak hunting.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can remove a bit of code duplication by reusing the new
fib6_nh_release_dsts helper in fib6_nh_release. Their only difference is
that fib6_nh_release's version doesn't use atomic operation to swap the
pointers because it assumes the fib6_nh is no longer visible, while
fib6_nh_release_dsts can be used anywhere.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel leaks memory when a `fib` rule is present in IPv6 nftables
firewall rules and a suppress_prefix rule is present in the IPv6 routing
rules (used by certain tools such as wg-quick). In such scenarios, every
incoming packet will leak an allocation in `ip6_dst_cache` slab cache.
After some hours of `bpftrace`-ing and source code reading, I tracked
down the issue to ca7a03c417 ("ipv6: do not free rt if
FIB_LOOKUP_NOREF is set on suppress rule").
The problem with that change is that the generic `args->flags` always have
`FIB_LOOKUP_NOREF` set[1][2] but the IPv6-specific flag
`RT6_LOOKUP_F_DST_NOREF` might not be, leading to `fib6_rule_suppress` not
decreasing the refcount when needed.
How to reproduce:
- Add the following nftables rule to a prerouting chain:
meta nfproto ipv6 fib saddr . mark . iif oif missing drop
This can be done with:
sudo nft create table inet test
sudo nft create chain inet test test_chain '{ type filter hook prerouting priority filter + 10; policy accept; }'
sudo nft add rule inet test test_chain meta nfproto ipv6 fib saddr . mark . iif oif missing drop
- Run:
sudo ip -6 rule add table main suppress_prefixlength 0
- Watch `sudo slabtop -o | grep ip6_dst_cache` to see memory usage increase
with every incoming ipv6 packet.
This patch exposes the protocol-specific flags to the protocol
specific `suppress` function, and check the protocol-specific `flags`
argument for RT6_LOOKUP_F_DST_NOREF instead of the generic
FIB_LOOKUP_NOREF when decreasing the refcount, like this.
[1]: ca7a03c417/net/ipv6/fib6_rules.c (L71)
[2]: ca7a03c417/net/ipv6/fib6_rules.c (L99)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215105
Fixes: ca7a03c417 ("ipv6: do not free rt if FIB_LOOKUP_NOREF is set on suppress rule")
Cc: stable@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to match ipv4 behaviour, see __ip_sock_set_tos()
implementation.
Technically for ipv6 this might not be required because normally we
do not allow tclass to influence routing, yet the cli tooling does
support it:
lpk11:~# ip -6 rule add pref 5 tos 45 lookup 5
lpk11:~# ip -6 rule
5: from all tos 0x45 lookup 5
and in general dscp/tclass based routing does make sense.
We already have cases where dscp can affect vlan priority and/or
transmit queue (especially on wifi).
So let's just make things match. Easier to reason about and no harm.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Link: https://lore.kernel.org/r/20211123223208.1117871-1-zenczykowski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This is to match ipv4 behaviour, see __ip_sock_set_tos()
implementation at ipv4/ip_sockglue.c:579
void __ip_sock_set_tos(struct sock *sk, int val)
{
if (sk->sk_type == SOCK_STREAM) {
val &= ~INET_ECN_MASK;
val |= inet_sk(sk)->tos & INET_ECN_MASK;
}
if (inet_sk(sk)->tos != val) {
inet_sk(sk)->tos = val;
sk->sk_priority = rt_tos2priority(val);
sk_dst_reset(sk);
}
}
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20211123223154.1117794-1-zenczykowski@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All gro_complete() handlers are called from napi_gro_complete()
while rcu_read_lock() has been called.
There is no point stacking more rcu_read_lock()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All gro_receive() handlers are called from dev_gro_receive()
while rcu_read_lock() has been called.
There is no point stacking more rcu_read_lock()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We need a way to release a fib6_nh's per-cpu dsts when replacing
nexthops otherwise we can end up with stale per-cpu dsts which hold net
device references, so add a new IPv6 stub called fib6_nh_release_dsts.
It must be used after an RCU grace period, so no new dsts can be created
through a group's nexthop entry.
Similar to fib6_nh_release it shouldn't be used if fib6_nh_init has failed
so it doesn't need a dummy stub when IPv6 is not enabled.
Fixes: 7bf4796dd0 ("nexthops: add support for replace")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We deal with IPv6 packets, so we need to use IP6CB(skb)->flags and
IP6SKB_REROUTED, instead of IPCB(skb)->flags and IPSKB_REROUTED
Found by code inspection, please double check that fixing this bug
does not surface other bugs.
Fixes: 09ee9dba96 ("ipv6: Reinject IPv6 packets if IPsec policy matches after SNAT")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tobias Brunner <tobias@strongswan.org>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Tested-by: Tobias Brunner <tobias@strongswan.org>
Acked-by: Tobias Brunner <tobias@strongswan.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memset(), avoid intentionally writing across
neighboring fields.
Use memset_after() to clear everything after the dst_entry member of
struct rt6_info.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macro 'swap()' defined in 'include/linux/minmax.h' to avoid
opencoding it.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Yao Jing <yao.jing2@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The offset value is used in pointer math on skb->data.
Since ipv6_skip_exthdr may return -1 the pointer to uh and th
may not point to the actual udp and tcp headers and potentially
overwrite other stuff. This is why I think this should be checked.
EDIT: added {}'s, thanks Kees
Signed-off-by: Jordy Zomer <jordy@pwning.systems>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to inet v4 raw sockets for binding to nonlocal addresses
through the IP_FREEBIND and IP_TRANSPARENT socket options, as well as
the ipv4.ip_nonlocal_bind kernel parameter.
Add helper function to inet_sock.h to check for bind address validity on
the base of the address type and whether nonlocal address are enabled
for the socket via any of the sockopts/sysctl, deduplicating checks in
ipv4/ping.c, ipv4/af_inet.c, ipv6/af_inet6.c (for mapped v4->v6
addresses), and ipv4/raw.c.
Add test cases with IP[V6]_FREEBIND verifying that both v4 and v6 raw
sockets support binding to nonlocal addresses after the change. Add
necessary support for the test cases to nettest.
Signed-off-by: Riccardo Paolo Bestetti <pbl@bestov.io>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20211117090010.125393-1-pbl@bestov.io
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
siphash keys use 16 bytes.
Define siphash_aligned_key_t macro so that we can make sure they
are not crossing a cache line boundary.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
