MMP2 have the internal sram, this sram can be allocated
for video, power management and secure processor.
Now the sram usage is:
0xd1000000 ~ 0xd101ffff (128KB) : reserved for secure processor
0xd1020000 ~ 0xd1037fff (96KB) : for video and PM
Register the internal sram's second half 96KB buffer,
so that video and PM can dynamically alloc/free from it.
Signed-off-by: Leo Yan <leoy@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
MMP platform has sram for the audio island;
Add the device structure for the audio sram,
and register the audio sram device at init phase.
Signed-off-by: Leo Yan <leoy@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
On mmp platform, there have two sram banks:
audio sram and internal sram. The audio sram is mainly for audio;
the internal sram is for video, wtm and power management.
So add the sram allocator using genalloc to manage them.
Every sram bank will register its own platform device
info, after the sram allocator create the generic pool
for the sram bank, the user module can use the pool's
name to get the pool handler; then it can use the handler
to alloc/free memory with genalloc APIs.
Signed-off-by: Leo Yan <leoy@marvell.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
v2:
- register_syscore_ops(&s3c24xx_irq_syscore_ops) does not need to be
conditionally compiled out, it is already optimized out on !CONFIG_PM
- fix also s3c2412 and s3c2416 affected by the same build issue
v1:
s3c2440.c fails to build if !CONFIG_PM because in such case
s3c2410_pm_syscore_ops is not defined. Same error should happen also
in s3c2410.c and s3c2442.c
Signed-off-by: Domenico Andreoli <cavokz@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Offsets of the irq controller registers were calculated
correctly only for first GPIO bank. This patch fixes
calculation of the register offsets for all GPIO banks.
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The IS_SAMSUNG_CPU() macro works by comparing the CPU ID mask exactly with
the CPU ID. This was failing for S3C64xx SoCs as in order to support
identification of the exact device the mask covers both variants of the
chip, meaning that the test would always fail on S3C6410 devices. This in
turn caused the core GPIO subsystem to fail to identify the CPU and not
support any GPIOs, crippling the system.
As a minimally invasive fix change the test for the class to be done by
checking each implementation and oring them together.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is unneeded and causes an abort on the SPMP8000 platform.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Zoltan Devai <zoss@devai.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Per the text in Documentation/SubmitChecklist as below, we should
explicitly have header linux/errno.h in localtimer.h for ENXIO
reference.
1: If you use a facility then #include the file that defines/declares
that facility. Don't depend on other header files pulling in ones
that you use.
Otherwise, we may run into some compiling error like the following one,
if any file includes localtimer.h without CONFIG_LOCAL_TIMERS defined.
arch/arm/include/asm/localtimer.h: In function ‘local_timer_setup’:
arch/arm/include/asm/localtimer.h:53:10: error: ‘ENXIO’ undeclared (first use in this function)
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Using COHERENT_LINE_{MISS,HIT} for cache misses and references
respectively is completely wrong. Instead, use the L1D events which
are a better and more useful approximation despite ignoring instruction
traffic.
Reported-by: Alasdair Grant <alasdair.grant@arm.com>
Reported-by: Matt Horsnell <matt.horsnell@arm.com>
Reported-by: Michael Williams <michael.williams@arm.com>
Cc: stable@kernel.org
Cc: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit af337f3e63
"ARM: S3C2443: Move parts of the clock code to common clock file",
the init_clocks array is moved to arch/arm/plat-s3c24xx/s3c2443-clock.c.
Now we call s3c_register_clocks for init_clocks in s3c2443_common_init_clocks.
Thus we can remove the empty init_clocks array here and remove the
redundant s3c_register_clocks call for init_clocks in s3c2443_init_clocks.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
S3C2443 uses hsmmc1 as its only hsmmc device and for S3C2416/S3C2450
it's the second hsmmc channel with the same PCLKCON bit.
The hsmmc-if clocks on both systems already got a devname, as did
the hsmmc pclk for hsmmc0 on the S3C2416. So to make it possible to
identify the hsmmc1 pclk on S3C2416 add the correct devname for it.
The sclk name on S3C2443 also is s3c-sdhci.1.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Previously the fclk rate was calculated by dividing the pll through
the divider value of the armdiv. With a real armdiv clk in place it's
possible to simply read its value, which does essentially the same.
This change makes the whole fdiv_fn function pointers supplied to
s3c2443_common_init_clocks and s3c2443_common_setup_clocks
obsolete, so remove it too.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Cpufreq uses frequencies in kHz and not Hz, so set_rate and round_rate
would be called with a frequency of 266666000 instead of 266666666 but
the clock functions check for rates smaller or equal to the targetrate.
As the armdiv does not support steps this small we can accommodate
this by simply also setting the last 3 digits of the calculated rate
to zero.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The armdiv array may contain unset divider values.
Check the relevant value to prevent division by zero
errors. Also check for set nr_armdiv and armdivmask
before meddling with clkdiv0.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The system-layout of the armdiv and armclk is common to
S3C2443/S3C2416/S3C2450 and only differs in the array of
possible dividers. Therefore it is possible to reuse the
clock definitions for all of these SoCs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is needed for making the armdiv clock common to S3C2443
and S3C2416/2450.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S3C2416/2450 has only 3 bits for the armdiv setting instead
of the 4 bits of the S3C2443.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add voltage regulator and platform data definition for M-5MOLS sensor
and MIPI-CSI receiver drivers. Add CAM power domain dependencies for
FIMC device and set up camera port A GPIO. Configure I2C0 bus timings.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: HeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch enables multi-format codec (MFC) support on ORIGEN board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The ADC of the S3C2416/2450 SoC is 10 or 12 bit wide, has its
source selection in the register base+0x18 and its width
selection in bit 03 of the ADCCON register.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S3C2443-adc is 10 bit wide and has its mux-select
in an extra register at base+0x18
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The adc blocks of S3C2443 and S3C2416 contain quirks not present
in the stock S3C24xx adc. Therefore allow them to alter the
device name via s3c_adc_setname.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The mux bits in the adccon register should be cleared only
if muxing is really done in ADCCON and not another register.
This patch introduces a conditional for this.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The adc blocks of the S3C2443 and S3C2416 define some
additional registers and bits.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The S3C64xx CPUs have TCMs so enable the kernel support for it
on these systems.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch registers all the available power domains on ORIGEN board.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Since the DC5V line is connected directly to the HDMI connector,
"hdmi-en" regulator would become a dummy regulator on origen board
(by defining REGULATOR_DUMMY in the kernel config file).
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'fixes' of git://git.linaro.org/people/arnd/arm-soc:
ARM: mach-ux500: enable fix for ARM errata 754322
ARM: OMAP: musb: Remove a redundant omap4430_phy_init call in usb_musb_init
ARM: OMAP: Fix i2c init for twl4030
ARM: OMAP4: MMC: fix power and audio issue, decouple USBC1 from MMC1
This fixes a compilation error in cpu-tegra.c which was introduced in
dc8d966bcc ("ARM: convert PCI defines to variables") which removed the
now obsolete mach/hardware.h from the mach-tegra subtree.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This helps resolve the conflicts between the imx cleanups and the
new code that has gone into the imx tree.
Conflict resolution was originally done by Sascha Hauer.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This applies ARM errata fix 754322 for all ux500 platforms.
Cc: stable@kernel.org
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sleep code for S5PV210 and EXYNOS4 are identical; moreover
S5p64X0 and S5PC100 for which support will be added soon can
use the same procedure. Create a common sleep code in the plat-s5p
directory so that it can be re-used.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Pave the way for adding PM support on S5P64X0, which is more similar
to the S3C64XX series than the S5P series. Hence, the common pm code
(containing dummy functions) should not be used for S5P64X0.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
