Fix a problem where 578xx-KR is unable to get link when connected to 1G link
partner. Two fixes were required:
One was to force CL37 sync_status low to prevent Warpcore from getting stuck in
CL73 parallel detect loop while link partner is sending.
Second fix was to enable auto-detect mode, thus allowing the Warpcore to select
the higher speed protocol between 10G-KR (over CL73), or go down to 1G over CL73
when there's indication for it.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even with the quirks in commit dabdaf0c (mcs7830: Fix link state
detection) there are still spurious link-down events for some chips
where the false link-down events count go over a few hundreds.
This patch takes a more conservative approach and only looks at
link-down events where the link-down state is not combined with other
states (e.g. half/full speed, pending frames in SRAM or TX status
information valid). In all other cases we assume the link is up.
Tested on MCS7830CV-DA (USB ID 9710:7830).
Cc: Ondrej Zary <linux@rainbow-software.org>
Cc: Michael Leun <lkml20120218@newton.leun.net>
Cc: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the vlan code detects that the real device can do TX VLAN offloads
in hardware, it tries to arrange for the real device's header_ops to
be invoked directly.
But it does so illegally, by simply hooking the real device's
header_ops up to the VLAN device.
This doesn't work because we will end up invoking a set of header_ops
routines which expect a device type which matches the real device, but
will see a VLAN device instead.
Fix this by providing a pass-thru set of header_ops which will arrange
to pass the proper real device instead.
To facilitate this add a dev_rebuild_header(). There are
implementations which provide a ->cache and ->create but not a
->rebuild (f.e. PLIP). So we need a helper function just like
dev_hard_header() to avoid crashes.
Use this helper in the one existing place where the
header_ops->rebuild was being invoked, the neighbour code.
With lots of help from Florian Westphal.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull powerpc fixes from Ben Herrenschmidt:
"A bit more endian problems found during testing of 3.13 and a few
other simple fixes and regressions fixes"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix alignment of secondary cpu spin vars
powerpc: Align p_end
powernv/eeh: Add buffer for P7IOC hub error data
powernv/eeh: Fix possible buffer overrun in ioda_eeh_phb_diag()
powerpc: Make 64-bit non-VMX __copy_tofrom_user bi-endian
powerpc: Make unaligned accesses endian-safe for powerpc
powerpc: Fix bad stack check in exception entry
powerpc/512x: dts: disable MPC5125 usb module
powerpc/512x: dts: remove misplaced IRQ spec from 'soc' node (5125)
Pull networking fixes from David Miller:
"Some holiday bug fixes for 3.13... There is still one bug I'd like to
get fixed before 3.13-final.
The vlan code erroneously assignes the header ops of the underlying
real device to the VLAN device above it when the real device can
hardware offload VLAN handling. That's completely bogus because
header ops are tied to the device type, so they only expect to see a
'dev' argument compatible with their ops.
The fix is the have the VLAN code use a special set of header ops that
does the pass-thru correctly, by calling the underlying real device's
header ops but _also_ passing in the real device instead of the VLAN
device.
That fix is currently waiting some testing.
Anyways, of note here:
1) Fix bitmap edge case in radiotap, from Johannes Berg.
2) Fix oops on driver unload in rtlwifi, from Larry Finger.
3) Bonding doesn't do locking correctly during speed/duplex/link
changes, from Ding Tianhong.
4) Fix header parsing in GRE code, this bug has been around for a few
releases. From Timo Teräs.
5) SIT tunnel driver MTU check needs to take GSO into account, from
Eric Dumazet.
6) Minor info leak in inet_diag, from Daniel Borkmann.
7) Info leak in YAM hamradio driver, from Salva Peiró.
8) Fix route expiration state handling in ipv6 routing code, from Li
RongQing.
9) DCCP probe module does not check request_module()'s return value,
from Wang Weidong.
10) cpsw driver passes NULL device names to request_irq(), from
Mugunthan V N.
11) Prevent a NULL splat in RDS binding code, from Sasha Levin.
12) Fix 4G overflow test in tg3 driver, from Nithin Sujir.
13) Cure use after free in arc_emac and fec driver's software
timestamp handling, from Eric Dumazet.
14) SIT driver can fail to release the route when
iptunnel_handle_offloads() throws an error. From Li RongQing.
15) Several batman-adv fixes from Simon Wunderlich and Antonio
Quartulli.
16) Fix deadlock during TIPC socket release, from Ying Xue.
17) Fix regression in ROSE protocol recvmsg() msg_name handling, from
Florian Westphal.
18) stmmac PTP support releases wrong spinlock, from Vince Bridgers"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
stmmac: Fix incorrect spinlock release and PTP cap detection.
phy: IRQ cannot be shared
net: rose: restore old recvmsg behavior
xen-netback: fix guest-receive-side array sizes
fec: Do not assume that PHY reset is active low
tipc: fix deadlock during socket release
netfilter: nf_tables: fix wrong datatype in nft_validate_data_load()
batman-adv: fix vlan header access
batman-adv: clean nf state when removing protocol header
batman-adv: fix alignment for batadv_tvlv_tt_change
batman-adv: fix size of batadv_bla_claim_dst
batman-adv: fix size of batadv_icmp_header
batman-adv: fix header alignment by unrolling batadv_header
batman-adv: fix alignment for batadv_coded_packet
netfilter: nf_tables: fix oops when updating table with user chains
netfilter: nf_tables: fix dumping with large number of sets
ipv6: release dst properly in ipip6_tunnel_xmit
netxen: Correct off-by-one errors in bounds checks
net: Add some clarification to skb_tx_timestamp() comment.
arc_emac: fix potential use after free
...
Commit 2361613206, "of/irq: Refactor interrupt-map parsing" changed
the refcount on the device_node causing an error in of_node_put():
ERROR: Bad of_node_put() on /pci@800000020000000
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.13.0-rc3-dirty #2
Call Trace:
[c00000003e403500] [c0000000000144fc] .show_stack+0x7c/0x1f0 (unreliable)
[c00000003e4035d0] [c00000000070f250] .dump_stack+0x88/0xb4
[c00000003e403650] [c0000000005e8768] .of_node_release+0xd8/0xf0
[c00000003e4036e0] [c0000000005eeafc] .of_irq_parse_one+0x10c/0x280
[c00000003e4037a0] [c0000000005efd4c] .of_irq_parse_pci+0x3c/0x1d0
[c00000003e403840] [c000000000038240] .pcibios_setup_device+0xa0/0x2e0
[c00000003e403910] [c0000000000398f0] .pcibios_setup_bus_devices+0x60/0xd0
[c00000003e403990] [c00000000003b3a4] .__of_scan_bus+0x1a4/0x2b0
[c00000003e403a80] [c00000000003a62c] .pcibios_scan_phb+0x30c/0x410
[c00000003e403b60] [c0000000009fe430] .pcibios_init+0x7c/0xd4
This patch adjusts the refcount in the walk of the interrupt tree.
When a match is found, there is no need to increase the refcount
on 'out_irq->np' as 'newpar' is already holding a ref. The refcount
balance between 'ipar' and 'newpar' is maintained in the skiplevel:
goto label.
This patch also removes the usage of the device_node variable 'old'
which seems useless after the latest changes.
Signed-off-by: Cédric Le Goater <clg@fr.ibm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
This reverts commit e38c0a1fbc.
Nikita Yushchenko reports:
While trying to make freescale p2020ds and mpc8572ds boards working
with mainline kernel, I faced that commit e38c0a1f (Handle
Both these boards have uli1575 chip.
Corresponding part in device tree is something like
uli1575@0 {
reg = <0x0 0x0 0x0 0x0 0x0>;
#size-cells = <2>;
#address-cells = <3>;
ranges = <0x2000000 0x0 0x80000000
0x2000000 0x0 0x80000000
0x0 0x20000000
0x1000000 0x0 0x0
0x1000000 0x0 0x0
0x0 0x10000>;
isa@1e {
...
I.e. it has #address-cells = <3>
With commit e38c0a1f reverted, devices under uli1575 are registered
correctly, e.g. for rtc
OF: ** translation for device /pcie@ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address: 00000001 00000070
OF: parent bus is default (na=3, ns=2) on /pcie@ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 00000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=a0000000, s=20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 01000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 01000000 00000000 00000070
OF: parent bus is default (na=2, ns=2) on /
OF: walking ranges...
OF: PCI map, cp=0, s=10000, da=70
OF: parent translation for: 00000000 ffc10000
OF: with offset: 70
OF: one level translation: 00000000 ffc10070
OF: reached root node
With commit e38c0a1f in place, address translation fails:
OF: ** translation for device /pcie@ffe09000/pcie@0/uli1575@0/isa@1e/rtc@70 **
OF: bus is isa (na=2, ns=1) on /pcie@ffe09000/pcie@0/uli1575@0/isa@1e
OF: translating address: 00000001 00000070
OF: parent bus is default (na=3, ns=2) on /pcie@ffe09000/pcie@0/uli1575@0
OF: walking ranges...
OF: ISA map, cp=0, s=1000, da=70
OF: parent translation for: 01000000 00000000 00000000
OF: with offset: 70
OF: one level translation: 00000000 00000000 00000070
OF: parent bus is pci (na=3, ns=2) on /pcie@ffe09000/pcie@0
OF: walking ranges...
OF: default map, cp=a0000000, s=20000000, da=70
OF: default map, cp=0, s=10000, da=70
OF: not found !
Thierry Reding confirmed this commit was not needed after all:
"We ended up merging a different address representation for Tegra PCIe
and I've confirmed that reverting this commit doesn't cause any obvious
regressions. I think all other drivers in drivers/pci/host ended up
copying what we did on Tegra, so I wouldn't expect any other breakage
either."
There doesn't appear to be a simple way to support both behaviours, so
reverting this as nothing should be depending on the new behaviour.
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Rob Herring <robh@kernel.org>
This patch corrects a problem in stmmac_ptp.c, functions
stmmac_adjust_time and stmmac_adjust_freq where the incorrect spinlocks
were released. This patch also addresses a problem in stmmac_main,
function stmmac_init_ptp where the capability detection for
advanced timestamping was masked by message masking.
This patch was touch tested using linuxptp, and runs without the previously
observed instabilities. More extensive testing is ongoing.
Vince
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the way PHY IRQ handler is implemented (all real handling being pushed to
the workqueue and returning IRQ_HANDLED all the time PHY is active), we cannot
really claim that PHY IRQ can be shared when calling request_irq().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
recvmsg handler in net/rose/af_rose.c performs size-check ->msg_namelen.
After commit f3d3342602
(net: rework recvmsg handler msg_name and msg_namelen logic), we now
always take the else branch due to namelen being initialized to 0.
Digging in netdev-vger-cvs git repo shows that msg_namelen was
initialized with a fixed-size since at least 1995, so the else branch
was never taken.
Compile tested only.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sizes chosen for the metadata and grant_copy_op arrays on the guest
receive size are wrong;
- The meta array is needlessly twice the ring size, when we only ever
consume a single array element per RX ring slot
- The grant_copy_op array is way too small. It's sized based on a bogus
assumption: that at most two copy ops will be used per ring slot. This
may have been true at some point in the past but it's clear from looking
at start_new_rx_buffer() that a new ring slot is only consumed if a frag
would overflow the current slot (plus some other conditions) so the actual
limit is MAX_SKB_FRAGS grant_copy_ops per ring slot.
This patch fixes those two sizing issues and, because grant_copy_ops grows
so much, it pulls it out into a separate chunk of vmalloc()ed memory.
Signed-off-by: Paul Durrant <paul.durrant@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should not assume that the PHY reset is always active low.
Retrieve this information from the device tree instead, so that the PHY reset
can work on both cases.
Reported-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A deadlock might occur if name table is withdrawn in socket release
routine, and while packets are still being received from bearer.
CPU0 CPU1
T0: recv_msg() release()
T1: tipc_recv_msg() tipc_withdraw()
T2: [grab node lock] [grab port lock]
T3: tipc_link_wakeup_ports() tipc_nametbl_withdraw()
T4: [grab port lock]* named_cluster_distribute()
T5: wakeupdispatch() tipc_link_send()
T6: [grab node lock]*
The opposite order of holding port lock and node lock on above two
different paths may result in a deadlock. If socket lock instead of
port lock is used to protect port instance in tipc_withdraw(), the
reverse order of holding port lock and node lock will be eliminated,
as a result, the deadlock is killed as well.
Reported-by: Lars Everbrand <lars.everbrand@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5c0484e25e ('powerpc: Endian safe trampoline') resulted in
losing proper alignment of the spinlock variables used when booting
secondary CPUs, causing some quite odd issues with failing to boot on
PA Semi-based systems.
This showed itself on ppc64_defconfig, but not on pasemi_defconfig,
so it had gone unnoticed when I initially tested the LE patch set.
Fix is to add explicit alignment instead of relying on good luck. :)
[ It appears that there is a different issue with PA Semi systems
however this fix is definitely correct so applying anyway -- BenH
]
Fixes: 5c0484e25e ('powerpc: Endian safe trampoline')
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=67811
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
p_end is an 8 byte value embedded in the text section. This means it
is only 4 byte aligned when it should be 8 byte aligned. Fix this
by adding an explicit alignment.
This fixes an issue where POWER7 little endian builds with
CONFIG_RELOCATABLE=y fail to boot.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Prevent ioda_eeh_hub_diag() from clobbering itself when called by supplying
a per-PHB buffer for P7IOC hub diagnostic data. Take care to inform OPAL of
the correct size for the buffer.
[Small style change to the use of sizeof -- BenH]
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PHB diagnostic buffer may be smaller than PAGE_SIZE, especially when
PAGE_SIZE > 4KB.
Signed-off-by: Brian W Hart <hartb@linux.vnet.ibm.com>
Acked-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The powerpc 64-bit __copy_tofrom_user() function uses shifts to handle
unaligned invocations. However, these shifts were designed for
big-endian systems: On little-endian systems, they must shift in the
opposite direction.
This commit relies on the C preprocessor to insert the correct shifts
into the assembly code.
[ This is a rare but nasty LE issue. Most of the time we use the POWER7
optimised __copy_tofrom_user_power7 loop, but when it hits an exception
we fall back to the base __copy_tofrom_user loop. - Anton ]
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The generic put_unaligned/get_unaligned macros were made endian-safe by
calling the appropriate endian dependent macros based on the endian type
of the powerpc processor.
Signed-off-by: Rajesh B Prathipati <rprathip@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In EXCEPTION_PROLOG_COMMON() we check to see if the stack pointer (r1)
is valid when coming from the kernel. If it's not valid, we die but
with a nice oops message.
Currently we allocate a stack frame (subtract INT_FRAME_SIZE) before we
check to see if the stack pointer is negative. Unfortunately, this
won't detect a bad stack where r1 is less than INT_FRAME_SIZE.
This patch fixes the check to compare the modified r1 with
-INT_FRAME_SIZE. With this, bad kernel stack pointers (including NULL
pointers) are correctly detected again.
Kudos to Paulus for finding this.
Signed-off-by: Michael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Another smallish batch of fixes, it's been quiet due to the holidays. Nothing
controversial here, a handful of things across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJSwENxAAoJEIwa5zzehBx366gP/0qFx9RVr+PaRSR3faIWZ0+l
qOCoOJ4604aE7H9blhUOz7VoWMUfqy7vRnr5Brms73lNZGztBzIiS1bte7qRiHtQ
QZr7rV9hZpy4G7aiGWHT2wkqDSYlJb0mmb5Kxn72KznWmuod3alOVfeqtgGRDJD4
YnUAlI10KpGcYYQ2d6jwCvb/KBQrlufrxxRirgzm13JmiU2CzGpPWDpSx6E1/bQ6
4I8rzHehg2n0FQHIhNDsmSTbsRSPsVjRZ5iMZ4kh7PBSrHuwaLLSyKKf3P8cjGRe
dhdN06XLZCAk5JUIt6oQWN3XGq217cIDZyQKz4wapPIc2Do/MAWKhmad6JbJTJxO
nk/j/VJamAGKjh6OG5+BVVV1KAqwkY4zKKN4lSbV17NLxu6TlA3Jq0vTpCNCMDiQ
xuLgBifPyhJIlJKUAnc1Ev+DrNVOrRsq6keosayKHyeH3nW6mPTzTppHjLPNSI//
WYjbqqs7Pu1MzQgp11C4fIj5xeSpqvdUpQIYolJq51MyL5QGub7H28/jR0rU9sN1
1R9quyB53Z2RLSWV84o4j8qmlQwwu9v94KPkJ6Rkr1IU8a4WqRkAGTjbXAhEBAnb
FQ8uLBzaJbifWXmsnmcI4M5gm4HF4iJv+5J/l3hj7W/4l3B2XfKbyzBnEfJT1PFC
mSjTK4WRhemgztif285m
=FX+j
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Another smallish batch of fixes, it's been quiet due to the holidays.
Nothing controversial here, a handful of things across the board"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: pxa: fix USB gadget driver compilation regression
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Pull x86 fixes from Peter Anvin:
"There is a small EFI fix and a big power regression fix in this batch.
My queue also had a fix for downing a CPU when there are insufficient
number of IRQ vectors available, but I'm holding that one for now due
to recent bug reports"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Don't select EFI from certain special ACPI drivers
x86 idle: Repair large-server 50-watt idle-power regression
- Fix for a cpufreq regression causing stale sysfs files to be left
behind during system resume if cpufreq_add_dev() fails for one or
more CPUs from Viresh Kumar.
- Fix for a bug in cpufreq causing CONFIG_CPU_FREQ_DEFAULT_* to be
ignored when the intel_pstate driver is used from Jason Baron.
- System suspend fix for a memory leak in pm_vt_switch_unregister()
that forgot to release objects after removing them from
pm_vt_switch_list. From Masami Ichikawa.
- Intel Valley View device ID and energy unit encoding update for the
(recently added) Intel RAPL (Running Average Power Limit) driver
from Jacob Pan.
- Intel Bay Trail SoC GPIO and ACPI device IDs for the Low Power
Subsystem (LPSS) ACPI driver from Paul Drews.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABCAAGBQJSvh9MAAoJEILEb/54YlRxfJoQAJFzcqXlYsROgPSlYVEG0F80
Cop0MbYC/gr8XNiLXWGIRVVYHbxMNeAPk5vUPZg4E9L6cOeazwjFtnRB/Av3FpVo
XReYHpLbJXJ3VaVyJiw0tCHp/Ukw8Ds0VcURi8RdcrQdkmyXPtbfWcrE+7GmuA2z
jnZOJviws+mTnxdEHtaml2iZMM5jwvUmUeh3iytc8zOC3QR4I7cLkKnYNTrQatqZ
qYxu5e9VAKuTXBv7BeNHiViakKhoWPx0S3nKofoiOG5hGwg49HGVlJ3pH9CCfIli
jA1NpXOGyKzYLJv2fJPtgxQ+l7Mb8wu9hGbPJWaUI3MRa9vIxNok6qzYwAQcfCWD
p4iugfsaatyKbBSBu+mntczCM7wsl2+/gH3gWfDySRpxq8G9At1dduO9GMeD/pDi
QhYlFl0obR05F6R0hlkk2Pahx+5x5nub7dM2+8Oh+r8k6TlkFRg+BKe21MJGz/45
BHBmJkNkLpdUNKT2GhaQK6rhc5TSln3eYGjYDRRhRmV6/4US/hI1MtY6HYg2uWbk
J3xiMcUXAY/0DzC1zDzvwr4Cc+WRdNXbZGKmmhyc+fxEmjZZVGanfmqC0JFV3gni
32v1krQA8v3KANz2xjvnNwNLQzSypgVOHihUbPN34FGaE7fxp6PWqxwhRD6RyywK
gtIHNSZ0mKnmIR6oxq1a
=vQDX
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes and new device IDs from Rafael Wysocki:
- Fix for a cpufreq regression causing stale sysfs files to be left
behind during system resume if cpufreq_add_dev() fails for one or
more CPUs from Viresh Kumar.
- Fix for a bug in cpufreq causing CONFIG_CPU_FREQ_DEFAULT_* to be
ignored when the intel_pstate driver is used from Jason Baron.
- System suspend fix for a memory leak in pm_vt_switch_unregister()
that forgot to release objects after removing them from
pm_vt_switch_list. From Masami Ichikawa.
- Intel Valley View device ID and energy unit encoding update for the
(recently added) Intel RAPL (Running Average Power Limit) driver from
Jacob Pan.
- Intel Bay Trail SoC GPIO and ACPI device IDs for the Low Power
Subsystem (LPSS) ACPI driver from Paul Drews.
* tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
powercap / RAPL: add support for ValleyView Soc
PM / sleep: Fix memory leak in pm_vt_switch_unregister().
cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
cpufreq: remove sysfs files for CPUs which failed to come back after resume
ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs
- reset netfilter-bridge state when removing the batman-adv
header from an incoming packet. This prevents netfilter
bridge from being fooled when the same packet enters a
bridge twice (or more): the first time within the
batman-adv header and the second time without.
- adjust the packet layout to prevent any architecture from
adding padding bytes. All the structs sent over the wire
now have size multiple of 4bytes (unless pack(2) is used).
- fix access to the inner vlan_eth header when reading the
VID in the rx path.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=RDuB
-----END PGP SIGNATURE-----
Merge tag 'batman-adv-fix-for-davem' of git://git.open-mesh.org/linux-merge
Included changes:
- reset netfilter-bridge state when removing the batman-adv
header from an incoming packet. This prevents netfilter
bridge from being fooled when the same packet enters a
bridge twice (or more): the first time within the
batman-adv header and the second time without.
- adjust the packet layout to prevent any architecture from
adding padding bytes. All the structs sent over the wire
now have size multiple of 4bytes (unless pack(2) is used).
- fix access to the inner vlan_eth header when reading the
VID in the rx path.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
This patchset contains four nf_tables fixes, one IPVS fix due to
missing updates in the interaction with the new sedadj conntrack
extension that was added to support the netfilter synproxy code,
and a couple of one-liners to fix netnamespace netfilter issues.
More specifically, they are:
* Fix ipv6_find_hdr() call without offset being explicitly initialized
in nft_exthdr, as required by that function, from Daniel Borkmann.
* Fix oops in nfnetlink_log when using netns and unloading the kernel
module, from Gao feng.
* Fix BUG_ON in nf_ct_timestamp extension after netns is destroyed,
from Helmut Schaa.
* Fix crash in IPVS due to missing sequence adjustment extension being
allocated in the conntrack, from Jesper Dangaard Brouer.
* Add bugtrap to spot a warning in case you deference sequence adjustment
conntrack area when not available, this should help to catch similar
invalid dereferences in the Netfilter tree, also from Jesper.
* Fix incomplete dumping of sets in nf_tables when retrieving by family,
from me.
* Fix oops when updating the table state (dormant <-> active) and having
user (not base ) chains, from me.
* Fix wrong validation in set element data that results in returning
-EINVAL when using the nf_tables dictionary feature with mappings,
also from me.
We don't usually have this amount of fixes by this time (as we're already
in -rc5 of the development cycle), although half of them are related to
nf_tables which is a relatively new thing, and I also believe that holidays
have also delayed the flight of bugfixes to mainstream a bit.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=3A1e
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Fix a regression for wrong interrupt numbers for some devices after
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.
* tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
+ v3.13-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
* r8a7790 (R-Car H2) based Lager board
- Correct SHDI resource sizes
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa418 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
* r8a7778 (R-Car M1) based Bock-W board
- Correct DMA mask
This resolves a regression introduced by 4dcfa60071
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* r8a7740 (R-Mobile A1) based Armadillo board
- Add PWM backlight power supply
This resolves a regression introduced by 22ceeee16e
("pwm-backlight: Add power supply support") in v3.12.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=6ai1
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Second Round of Renesas ARM based SoC Fixes for v3.13
* r8a7790 (R-Car H2) based Lager board
- Correct SHDI resource sizes
This bug has been present since sdhi resources were added to the r8a7790 by
8c9b1aa418 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
templates") in v3.11-rc2.
* r8a7778 (R-Car M1) based Bock-W board
- Correct DMA mask
This resolves a regression introduced by 4dcfa60071
("ARM: DMA-API: better handing of DMA masks for coherent allocations")
in v3.12-rc1.
* r8a7740 (R-Mobile A1) based Armadillo board
- Add PWM backlight power supply
This resolves a regression introduced by 22ceeee16e
("pwm-backlight: Add power supply support") in v3.12.
* tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7790: fix shdi resource sizes
ARM: shmobile: bockw: fixup DMA mask
ARM: shmobile: armadillo: Add PWM backlight power supply
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
After commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header" a compilation
error was introduced in the PXA25x gadget driver.
An attempt to fix the problem was made in
commit b144e4ab1e
"usb: gadget: fix pxa25x compilation problems"
by explictly stating the driver needs the <mach/hardware.h>
header, which solved the compilation for a few boards,
such as the pxa255-idp and its defconfig.
However the Lubbock board has this special clause in
drivers/usb/gadget/pxa25x_udc.c:
This include file has an implicit dependency on
<mach/irqs.h> having been included before <mach/lubbock.h>
was included.
Before commit 88f718e3fa
"ARM: pxa: delete the custom GPIO header" this implicit
dependency for the pxa25x_udc compile on the Lubbock was
satisfied by <linux/gpio.h> implicitly including
<mach/gpio.h> which was in turn including <mach/irqs.h>,
apart from the earlier added <mach/hardware.h>.
Fix this by having the PXA25x <mach/lubbock.h> explicitly
include <mach/irqs.h>.
Reported-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg Kroah-Hartmann <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes dictionary mappings, eg.
add rule ip filter input meta dnat set tcp dport map { 22 => 1.1.1.1, 23 => 2.2.2.2 }
The kernel was returning -EINVAL in nft_validate_data_load() since
the type of the set element data that is passed was the real userspace
datatype instead of NFT_DATA_VALUE.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When batadv_get_vid() is invoked in interface_rx() the
batman-adv header has already been removed, therefore
the header_len argument has to be 0.
Introduced by c018ad3de6
("batman-adv: add the VLAN ID attribute to the TT entry")
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
If an interface enslaved into batman-adv is a bridge (or a
virtual interface built on top of a bridge) the nf_bridge
member of the skbs reaching the soft-interface is filled
with the state about "netfilter bridge" operations.
Then, if one of such skbs is locally delivered, the nf_bridge
member should be cleaned up to avoid that the old state
could mess up with other "netfilter bridge" operations when
entering a second bridge.
This is needed because batman-adv is an encapsulation
protocol.
However at the moment skb->nf_bridge is not released at all
leading to bogus "netfilter bridge" behaviours.
Fix this by cleaning the netfilter state of the skb before
it gets delivered to the upper layer in interface_rx().
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Make struct batadv_tvlv_tt_change a multiple 4 bytes long
to avoid padding on any architecture.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Since this is a mac address and always 48 bit, and we can assume that
it is always aligned to 2-byte boundaries, add a pack(2) pragma.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
struct batadv_icmp_header currently has a size of 17, which
will be padded to 20 on some architectures. Fix this by
unrolling the header into the parent structures.
Moreover keep the ICMP parsing functions as generic as they
are now by using a stub icmp_header struct during packet
parsing.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
The size of the batadv_header of 3 is problematic on some architectures
which automatically pad all structures to a 32 bit boundary. To not lose
performance by packing this struct, better embed it into the various
host structures.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
The compiler may decide to pad the structure, and then it does not
have the expected size of 46 byte. Fix this by moving it in the
pragma pack(2) part of the code.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
If not table name is specified, the dumping of the existing sets
may be incomplete with a sufficiently large number of sets and
tables. This patch fixes missing reset of the cursors after
finding the location of the last object that has been included
in the previous multi-part message.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
if a dst is not attached to anywhere, it should be released before
exit ipip6_tunnel_xmit, otherwise cause dst memory leakage.
Fixes: 61c1db7fae ("ipv6: sit: add GSO/TSO support")
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netxen_process_lro() contains two bounds checks. One for the ring number
against the number of rings, and one for the Rx buffer ID against the
array of receive buffers.
Both of these have off-by-one errors, using > instead of >=. The correct
versions are used in netxen_process_rcv(), they're just wrong in
netxen_process_lro().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
We've seen so many instances of people invoking skb_tx_timestamp()
after the device already has been given the packet, that it's worth
being a little bit more verbose and explicit in this comment.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
skb_tx_timestamp(skb) should be called _before_ TX completion
has a chance to trigger, otherwise it is too late and we access
freed memory.
Fixes: e4f2379db6 ("ethernet/arc/arc_emac - Add new driver")
From: Eric Dumazet <edumazet@google.com>
Cc: Alexey Brodkin <Alexey.Brodkin@synopsys.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current driver assumes that an skb fragment can only be upto jumbo
size. Presumably this was a fast-path optimization. This assumption is
no longer true as fragments can be upto 32k.
v2: Remove unnecessary parantheses per Eric Dumazet.
Cc: stable@vger.kernel.org
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJSvANxAAoJEMePsQ0LvSpLd0AP/1Toh0oIX7xdj9zaTosZgovZ
UsNbkzilxKWVGwyjEHj0510YL/v3YuYYPmF+UtZcOVEybz+EWP21BXJc0y+jX7QV
ma21i3abK0uKJ1Dq0CGmolnq9NRswvS2TR9SKgXmG/1HGF1wo5MIjzx3ZCtFdni4
+PZYG1RFJEFUBWtQoWnkqm16QS6wwzfIHlfLBy5kEu70ueFuAyLd7yKWgtjDkpWP
Yvf5mjvIdbDlK6sn9388UydYq4Puy8k0KWHlcQn/jA0uQecjt7gcsk6B24RPhPzt
l9H2wMRxoTBgx6di8ywGdU0XV6pa6A7DWQGhve2AjQlBZ5hug7i4oEOO4Iod6cMm
c3lqA2DEbLLt3Xwjj97EZYKiIlIxnYbqFdw/Ql0KdnlAwtZw333EkcRKW5+15Jsg
qcYU2GtsvGRqBgUD13eE7OLM9Ovgdkt18PYLEs5Vzsi08n+LDwuoZj4lpCHOsBZl
1xO38Q3M9NCmMUubfxbY0HvzW3EqgBZHFGgf3hWsbxkV89htCrDD+kwo1OTXCLXE
s3FFIAaa7HDdWJCD/CPfKoaY0upqv/DwsHwKNpvT8SiiVb90mNXumJauC1H8GeW9
gQqscy2u+UhtXtuPiYpG2h4tEGC95ySwzbolT4d84fbqmkMQLcfzSofgJ98iYg2N
vRGMA2I8U142M2HaCxZx
=kOrX
-----END PGP SIGNATURE-----
Merge tag 'for-v3.13-rc/hwmod-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into debug-ll-and-ldp-backlight-fix
A few OMAP hwmod fixes for v3.13-rc. One patch fixes some IRQ
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3. The other fixes
some problems with DEBUG_LL on DRA7xx.
Basic build, boot, and PM test logs are available here:
http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/
