This patch adds support for the new udc-core reset notifier to the
net2280 driver.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace usb_gadget_driver's disconnect with udc-core's reset notifier at
bus reset handler.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
SET_FEATURE request with DEBUG_MODE only worked the first time after module
initialisation. Per the USB 2.0 debug device specification, said request
is to be treated as if it were a SET_CONFIGURATION request, i.e. endpoint
must be re-configured.
As configure_endpoints() may now get called multiple times, move it outside
__init and move serial_alloc_tty() call into __init.
Code has assumption that endpoint mapping remains unchanged with consecutive
calls of configure_endpoints().
Signed-off-by: Kyösti Mälkki <kyosti.malkki@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The recent change bringing device-tree support triggers a warning in a
non device-tree build :
drivers/usb/gadget/udc/pxa27x_udc.c:2405:28: warning: 'udc_pxa_dt_ids'
defined but not used [-Wunused-variable]
Fix the warning with a preprocessor condition.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
as it turns out, at least AM437x silicon (non-FPGA)
needs to enable PHY suspend quirk. So let's allow
for PHY suspend quirk to be used with non-FPGA
builds too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make the hid function available for gadgets composed with configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Before configfs is integrated the usb_gstrings_attach() interface
must be used.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no old function interface users left, so remove it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new f_hid interface in order for the old to be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Converting hid to the new function interface requires converting
the USB hid's function code and its users.
This patch converts the f_hid.c to the new function interface.
The file can now be compiled into a separate usb_f_hid.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
So far platform driver has been unregistered first,
so just after that the usb composite is still available,
but there is no hid data any more.
Reverse the order so that first the usb composite becomes
unavailable and second the hid data goes away.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
device_create() might fail, so check its return value and react
appropriately.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
class_create() might fail, so check its return value and react
appropriately.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
File names in the heading comments fell out of favor long ago, and these weren't
even changed when the drivers were moved from drivers/usb/otg/, so remove them
at last...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make the midi function available for gadgets composed with configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In order to add configfs support the usb_gstrings_attach must be used.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no old f_midi interface users left, so remove it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new f_midi interface so that the old can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Converting midi to the new function interface requires converting
the USB midi's function code and its users.
This patch converts the f_midi.c to the new function interface.
The file can now be compiled into a separate usb_f_midi.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
kstrdup() might fail, so check its return value and react appropriately.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The soundcard index to use for the ALSA device creation is passed as a
parameter to f_midi_bind_config(), but is assigned to midi->index only
after the call to f_midi_register_card(midi). So no matter what is passed
to f_midi_bind_config(), the actual index for snd_card_new() is always 0.
This probably works ok if at the moment of f_midi's bind there are no
other snd_cards, but if there are, it is not possible to bind f_midi.
This patch moves the assignment to a place before the call to
f_midi_register_card(midi).
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
uac1 and uac2 functions are available through the configfs interface
and it should be possible to build them without building their legacy
gadgets.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following checkpatch warning.
WARNING: break is not useful after a goto or return
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Attaching a keyboard, using it as a wakeup via
|for f in $(find /sys/devices/ocp.3/47400000.usb -name wakeup)
|do
| echo enabled > $f
|done
going into standby
| echo standby > /sys/power/state
and now a wake up by a pressing a key.
What happens is that the system wakes up but the USB device is dead. The
USB stack tries to send a few control URBs but nothing comes back.
Eventually it gaves up and the device remains dead:
|[ 632.559678] PM: Wakeup source USB1_PHY
|[ 632.581074] PM: noirq resume of devices complete after 21.261 msecs
|[ 632.607521] PM: early resume of devices complete after 10.360 msecs
|[ 632.616854] net eth2: initializing cpsw version 1.12 (0)
|[ 632.704126] net eth2: phy found : id is : 0x4dd074
|[ 636.704048] libphy: 4a101000.mdio:00 - Link is Up - 1000/Full
|[ 638.444620] usb 1-1: reset low-speed USB device number 2 using musb-hdrc
|[ 653.713435] usb 1-1: device descriptor read/64, error -110
|[ 669.093435] usb 1-1: device descriptor read/64, error -110
|[ 669.473424] usb 1-1: reset low-speed USB device number 2 using musb-hdrc
|[ 684.743436] usb 1-1: device descriptor read/64, error -110
|[ 690.065097] PM: resume of devices complete after 57450.744 msecs
|[ 690.076601] PM: Finishing wakeup.
|[ 690.076627] Restarting tasks ...
It seems that since we got woken up via MUSB_INTR_RESUME the
musb_host_finish_resume() callback is executed before the
resume-callbacks of the PHY and glue layer are invoked. If I delay it
until the glue layer resumed then I don't see this problem.
I also move musb_host_resume_root_hub() into that callback since I don't
see any reason in doing anything resume-link if there are still pieces
not restored.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The am335x-evmsk support two kinds of suspend:
- standby
the USB device remains powered while the system goes into suspend
- mem
the USB device becomes powerless while the system goes into suspend.
In the "standby" case the device resumes quickly. In the "mem" case the
system hangs for a few seconds. It seems to me that the USB-device has
no address (it was disconnected) and the USB stack thinks that it is
fully operational and GetPortStatus returns the status from before the
suspend so it is not a big help here.
This adds a check in the resume path to see if the device mode (A or B)
and the speed is the same. If the device went missing between
suspend/resume (VBUS went down) then MUSB seems to go into B mode and
HS/FS bits are cleared. In that case we clear the port1_status bits and
assume a disconnect. Once the stack learns this it does a "logical
disconnect" and removes the USB-device quickly. Should the device remain
connected during the suspend then MUSB will receives a "CONNECT" interrupt.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
DWC3 Exynos Specific Glue layer can be used only for Exynos SoCs.
In addition, non-DT for EXYNOS SoCs is not supported from v3.11;
thus, there is no need to support non-DT for DWC3 Exynos Specific
Glue layer.
The 'linux/platform_data/dwc3-exynos.h' file has been used for
non-DT support. Thus, the 'dwc3-exynos.h' file is removed, because
it is not used anymore.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the DCPCTR doesn't have the ACLRM bit, the usbus_pipe_clear()
should not call the usbhsp_pipectrl_set() with ACLRM.
So, this patch fixes this issue to add the usbhs_fifo_clear_dcp()
in fifo.c because the controller needs the CFIFO to clear the
the DCP PIPE.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the datasheet, this driver should clear the INTSTS0.CTRT
bit before this controller detects the next stage transition. Otherwise,
the driver may not be able to clear the bit after the controller went to
the next stage transition. After that, the driver will not be able to
clear the INTSTS0.VALID, and a usb control transfer will not finish
finally.
If we use the testusb tool, it is easy to reproduce this issue:
# testusb -a -t 10
Since the previous code handled a data stage and a status stage in
the usbhsf_pio_try_push(), it may not clear the INTSTS0.CTRT at the
right timing.
So, this patch change the timing of usbhs_dcp_control_transfer_done()
to the usbhsg_irq_ctrl_stage().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that this driver always enable the D+ pullup
after it detected the VBUS connection even though this usb controller
can control the D+ pullup timing by software. So, this driver should
enable the D+ pullup after a gadget driver called usb_gadget_connect().
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that the NULL pointer dereference happens
when we uses g_audio driver. Since the g_audio driver will call
usb_ep_disable() in afunc_set_alt() before it calls usb_ep_enable(),
the uep->pipe of renesas usbhs driver will be NULL. So, this patch
adds a condition to avoid the oops.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 2f98382dc (usb: renesas_usbhs: Add Renesas USBHS Gadget)
Cc: <stable@vger.kernel.org> # v3.0+
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch allows the gadget portion of the DWC2 driver to get built when
(!USB && USB_GADGET) condition is encountered.
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
HIRD threshold should be configurable by different platforms.
From DesignWare databook:
When HIRD_Threshold[4] is set to 1b1 and HIRD value is greater than or
equal to the value in HIRD_Threshold[3:0], dwc3 asserts output signals
utmi_l1_suspend_n to put PHY into Deep Low-Power mode in L1.
When HIRD_Threshold[4] is set to 1b0 or the HIRD value is less than
HIRD_Threshold[3:0], dwc3 asserts output signals utmi_sleep_n on L1.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds support for AMD Nolan (NL) FPGA and SoC platform.
Cc: Jason Chang <jason.chang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb2 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disable usb3 suspend phy quirk, and some special platforms
can configure that if it is needed.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds Tx de-emphasis quirk, and the Tx de-emphasis value is
configurable according to PIPE3 specification.
Value Description
0 -6dB de-emphasis
1 -3.5dB de-emphasis
2 No de-emphasis
3 Reserved
It can be configured on DT or platform data.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is recommended to set USB3 and USB2 SUSPHY bits to '1' after the core
initialization is completed above the dwc3 revision 1.94a.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds RX_DETECT to Polling.LFPS control quirk, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds LFPS filter quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay PHY power change from P0 to P1/P2/P3 when link state
changing from U0 to U1/U2/U3 respectively, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds delay P0 to P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds request P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds P3 in U2 SS inactive quirk, and some special platforms can
configure that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds u2exit lfps quirk, and some special platforms can configure
that if it is needed.
[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.
This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.
[ balbi@ti.com : added devicetree documentation, spelled threshold
completely, made sure threshold is only applied to
proper core revisions. ]
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch initializes platform data at pci glue layer, and SoCs x86-based
platform vendor is able to define their flags in platform data at bus glue
layer. Then do some independent behaviors at dwc3 core level.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some chip vendor is on pre-silicon phase, which needs to use the simulation
board. It should have the same product and vendor id with the true soc, but
might have some minor different configurations.
Below thread discussion proposes to find a method to distinguish between
simulation board and soc.
http://marc.info/?l=linux-usb&m=141194772206369&w=2
In Andvanced Configuration of coreConsultant, there is the parameter of
DWC_USB_EN_FPGA. This bit has the function we need. And it would response as 7
bit of GHWPARAMS6 register. So it's able to check this functional bit to confirm
if works on FPGA board.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
