Unnecessary cast from void* in assignment.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
add support for hsusb host ports 1, 2 and on-module usb hub.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When changing the L3 clock frequency, the CPU is executing from internal RAM
and the SDRC clock is disabled. During this time accesses made to external
DDR are stalled. If the ARM subsystem attempts to access the DDR while the
SDRC clock is disabled this will stall the CPU until the access to the SDRC
timeouts. A timeout on the SDRC should never occur. Once a timeout occurs all
the following accesses will be aborted and the DDR is no longer accessible.
Although the code being executed in the internal RAM does not directly access
the DDR, it was found that the branch prediction logic in the CPU may cause
the CPU to prefetch code from a DDR location while the SDRC clock is disabled.
This was causing an SDRC timeout which resulted in a system hang.
This patch fixes this problem by ensuring the branch prediction logic is
disabled while changing the L3 clock frequency. The branch prediction logic
is disabled by clearing the Z-bit in the ARM CTRL register.
Disabling the branch prediction logic does not have any noticable impact
on the execution time of this code section. The hardware observability
signals were used to monitor the sdrc idle time with and without this
patch when operating at different CPU frequencies (150MHz, 500MHz and
600MHz) and the total sdrc idle time when changing frequenct was in
the range of 9-11us. This was measured on an omap3430 SDP running the
omapzoom p-android-omap-2.6.29 branch.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
This patch has multiple fixes together. To ensure that git bisect work across
commits, all changes are clubbed together
1. Move the common control base address to control core
2. Remove the manually coeded defines and use the ones from headers.
3. Fix the the status register define in id.c for OMAP4
4. Fix all the register define in hsmmc.c
5. Use the control pad accessor API for omap4 hsmmc register accesses
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4, control module is divided into 4 separate IPs
- OMAP44XX_CTRL_MODULE_CORE
- OMAP44XX_CTRL_MODULE_PAD_CORE
- OMAP44XX_CTRL_MODULE_WKUP
- OMAP44XX_CTRL_MODULE_PAD_WKUP
This patch adds all the omap4 control module register data and
includes them in the common control.h
The register data is autogenerated from the codebase thanks
to Benoit Cousson efforts
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 control pad are not addressable from control
core base. So the common omap_ctrl_read/write APIs breaks
Hence export separate APIs to manage the omap4 pad control
registers.
This APIs will work only for OMAP4
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On omap4 control module is divided in four IP blocks.
- CTRL_MODULE_CORE 0x4a002000
- CTRL_MODULE_PAD_CORE 0x4a100000
- CTRL_MODULE_WKUP 0x4a30c000
- CTRL_MODULE_PAD_WKUP 0x4a31e000
Addressing all the modules with single base address is not possible
considering 16 bit offsets. The mux code manages the pad core and pad
wakeup related base address inside the mux framework. For other usage
only control core and control pad bases are necessary. So this patch
maps only needed pad control base address which is used by device drivers
and infrastructure code
The main control core base is still kept same in this patch to
keep git-bisect working. This will be fixed in the relevant patch
in this series.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Fix a few OMAP4430 clock tree problems after the recent manual merge of the
various ES2 clock patches:
- usim optional clock and its parent had the same name, rename the parent
usim_fclk -> usim_ck
- OPTFCLKEN_CLK32K is not handled anymore by the USBPHYOCP2SCP module in ES2
Create a new clock that belongs to CM_ALWON_USBPHY_CLKCTRL register
This patch depends on some of the PRCM macro updates from Rajendra.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: tweaked patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
DSS on ES2 supports only OSWR, hence remove the support
for CSWR from the powerdomain framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
4430 ES2 has a few new registers added and a few modified
from ES1. This patch adds all the register changes in PRM
and CM for OMAP4430 ES2.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
This patch updates the PRM and CM register bitshifts and masks
for OMAP4430 ES2.0.
Replace as well the BITFIELD macro with the shift operator in order
to be consistent with the previous OMAP2 & 3 format.
Sort the register list in comments in order to have a consistent
register order and avoid futur change during code generation.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 IP optional clocks require explicit enable in module CTRLCLK
register. In order to allow that we have to create artificial clock
nodes that represent this clock inputs in the IP.
Notes:
- Temporary use OMAP3 names for GPIO optional clocks until the GPIO hwmod
convertion is done. It will enforce the usage of OMAP4 names as the reference.
- Temporary use OMAP3 names for TIMER main clock (gptX_fck) until TIMER hwmod
convertion is done. During that convertion, the new name will have to be used.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The OMAP4 hwmod data introduced the new naming convention for TI
IPs (See patch OMAP4: hwmod: Add partial hwmod support for OMAP4430 ES1.0)
The leaf clock names are using the same IP name and thus must be
modified to match the clock populated in the hwmod data.
- Fix some leaf clocks nodes that were using a _iclk instead of the _fclk
prefix.
- Fix some wrong interface clock name for master IPs connected to
interconnect.
Please not that due to the fact that nodes are sorted by name, the name
change will introduce a quite ugly diff a little bit hard to follow.
Timers clock con_id is still using the old gptX_fck name until the
gptimer driver is updated to omap_device framework.
Timers entries in hwmods DB are still disabled until the migration
if timer to platform_driver + omap_hwmod.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: manually resolved conflicts with Rajendra's clock patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
This patch updates the clock tree with all the
changes in OMAP4430 ES2.
clock nodes added
-1- tie_low_clock_ck
-2- abe_dpll_bypass_clk_mux_ck
clock nodes deleted
-1- dpll_sys_ref_clk
-2- per_sgx_fclk
-3- usbphyocp2scp_ick
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
[paul@pwsan.com: added comment re ES1 clocks to top of file]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This 'legacy' OMAP2420 McBSP2 muxing code is currently broken after recent
conversion to new mux code. The omap_mcbsp_request calling this code is
usually called after booting whereas the omap_mux_init_signal is __init
marked so null pointer dereference would occur.
Fix this by removing the muxing code and let the bootloader or board file to
do it if necessary. Remove also omap2_mcbsp_ops as there is no use for it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Updates to enable omap aes
Signed-off-by: Dmitry Kasatkin <dmitry.kasatkin@nokia.com>
[tony@atomide.com: updated to use CONFIG_ARCH_OMAP2/3 instead of old 24XX/34XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
At Pandaboard we have 2 status leds, so adding them with similar usage as
we have for Beagleboard (heartbeat and mmc0). The patch basically adds the
platform data required by leds-gpio driver.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap 4430sdp board support for the proximity sensor via GPIO keys.
The proximity sensor is connected to GPIO and is registered as a
GPIO key.
- Making the default state of the sensor off at bootup
- The init is called before platform_add_devices
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP USBOTG module has a requirement to set the autoidle bit only after
setting smartidle bit. Modified the _sys_enable api to set the smartidle
first and then the autoidle bit. Setting this will not have any impact on the
other modules.
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap4_cm_wait_module_ready function would only check for
the modules to be completely functional before declaring them
ready to be accessed.
There might also be instances where in the module is actually
in idle (under h/w control) but should still be declared
accessible, as the h/w control would make it functional when
needed.
Hence make omap4_cm_wait_module_ready return true in case
the module is fully functional *or* in idle state.
Fail only if the module is fully disabled or stuck intransition.
The explaination from the TRM for the idlest bits on OMAP4 is as
below for quick reference
Module idle state:
0x0 func: Module is fully functional, including OCP
0x1 trans: Module is performing transition: wakeup, or sleep, or sleep
abortion
0x2 idle: Module is in Idle mode (only OCP part). It is functional if
using separate functional clock
0x3 disabled: Module is disabled and cannot be accessed
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On ES2.0 the L2 cache init parameter ineeds to be changed to take
care of cache size. The cache size is 1MB on ES2.0 vs 512KB on ES1.0
This patch fixes the init parameter to update the same using
dynamic cpu version check
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch updates the id.c and cpu.h files to support
omap4 ES2.0 silicon detection. Few initial omap4 es2 samples
IDCODE is same as es1. So the patch uses ARM cpuid register to
detect the ES version for such samples
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Bootloader on Nokia N800 and N810 muxes I2C codec port pins for EAC block.
As there is no driver and use for EAC, mux those pins for McBSP instead
since N810 ASoC drivers can use it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Second i2c bus on Nokia N800 and N810 shares both common and hw specific
peripherals. Register now this bus and add board info with tlv320aic3x for
N810. Common peripherals may be added as an additional board info to
omap_register_i2c_bus(2, ...);
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Move n8x0_i2c_board_info_1 out from #ifdef CONFIG_MENELAUS block,
register i2c1 in n8x0_init_machine and do a few clean-ups around these.
Code looks better if board infos are grouped together
- Mark n8x0_i2c_board_info_1 and n8x0_menelaus_platform_data with __initdata
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes these compiler warnings:
CC arch/arm/mach-omap2/mux.o
arch/arm/mach-omap2/mux.c: In function 'omap_mux_init_gpio':
arch/arm/mach-omap2/mux.c:90: warning: 'gpio_mux' may be used uninitial
ized in this function
CC arch/arm/plat-omap/gpio.o
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_resume_after_idle':
arch/arm/plat-omap/gpio.c:2152: warning: 'l' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c: In function 'omap2_gpio_prepare_for_idle':
arch/arm/plat-omap/gpio.c:2085: warning: 'l2' may be used uninitialized
in this function
arch/arm/plat-omap/gpio.c:2085: warning: 'l1' may be used uninitialized
in this function
CC arch/arm/mach-omap2/board-omap4panda.o
arch/arm/mach-omap2/board-omap4panda.c: In function 'omap4_panda_init':
arch/arm/mach-omap2/board-omap4panda.c:277: warning: unused variable 's
tatus'
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding i2c eeprom driver to access monitor EDID binary information
from user space, something that is required by 'decode-edid' and
'parse-edid'.
BugLink: https://bugs.launchpad.net/bugs/608279
Signed-off-by: Mathieu Poirier <mathieu.poirier@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap3630 based BeagleBoard xM uses a MicroSD card slot with
no write protection.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
system_rev comes from u-boot and is a constant 0x20, so
Bx boards also fall in this 'if' and will get setup with the
wrong gpio_wp pin. Switch to using the Beagle revision routine
to correcly set pin 23 only for C1/2/3 and C4 Boards. Bx boards
will then use the correct default pin setting.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Due to the omap3530 ES3.0 Silicon being used on both the
B5/B6 and C1/2/3 Beagle we can't use the cpu_is_omap34xx()
routines to differentiate the Beagle Boards.
However gpio pins 171,172,173 where setup for this prupose, so
lets use them.
Changes:
for older U-Boot's, use omap_mux_init_gpio()
keep Beagle Rev in board-omap3beagle.c
gpio_free on gpio request failure
Tested on Beagle Revisions: B5, C2, C4, and xMA
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board file changes for the digital compass hmc5843.
The interface to the device is i2c.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP4 L3 interconnect is split in 3 part for power saving reason.
Because of that there is no l3_main like on OMAP2 & 3 but 3 differentes
l3_main_X instances.
In the case of OMAP4, query only the l3_main_1 part. The clock and
voltage are shared across the 3 instances.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The current version contains only the interconnects and the
mpu hwmods.
The remaining hwmods will be introduced by further patches on
top of this one.
- enable as well omap_hwmod.c build for OMAP4 Soc
Please not that this file uses the new naming convention for
naming HW IPs. This convention will be backported soon for previous
OMAP2 & 3 data files.
new name trm name
------------- -------------------
counter_32k synctimer_32k
l3_main l3
timerX gptimerX / dmtimerX
mmcX mmchsX / sdmmcX
dma_system sdma
smartreflex_X sr_X / sr?
usb_host_fs usbfshost
usb_otg_hs hsusbotg
usb_tll_hs usbtllhs_config
wd_timerX wdtimerX
ipu cortexm3 / ducati
dsp c6x / tesla
iva ivahd / iva2.2
kbd kbdocp / keyboard
mailbox system_mailbox
mpu cortexa9 / chiron
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When the clockdomain layer initializes, place all clockdomains into
software-supervised mode, and clear all wakeup and sleep dependencies
immediately, rather than waiting for the PM code to do this later.
This fixes a major bug where critical sleep dependencies added by the
hwmod code are cleared during late PM init.
As a side benefit, the _init_{wk,sleep}dep_usecount() functions are no
longer needed, so remove them.
Kevin Hilman <khilman@deeprootsystems.com> did all the really hard work on
this, identifying the problem and finding the bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The set_pwrdm_state() is needed on omap4 as well so move
this routine to common pm.c file so that it's available for omap3/4
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Commit 8e2efde9 added milliseconds suspend wakeup time support but
same interface is not exported through debugfs
This patch enables the debugfs hook for wakeup_timer_milliseconds
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch moves omap2_pm_wakeup_on_timer() and pm debug entries
form pm34xx.c to pm-debug.c and export it, so that it is available
to other OMAPs
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
