As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + size * count" in the kzalloc() function.
[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210905155728.11147-1-len.baker@gmx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Fix a kernel crash when a signal is delivered to bad userspace stack
- Fix fall-through warnings in math-emu code
- Increase size of gcc stack frame check
- Switch coding from 'pci_' to 'dma_' API
- Make struct parisc_driver::remove() return void
- Some parisc related Makefile changes
- Minor cleanups, e.g. change to octal permissions, fix macro collisions,
fix PMD_ORDER collision, replace spaces with tabs
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQS86RI+GtKfB8BJu973ErUQojoPXwUCYTELwQAKCRD3ErUQojoP
Xy/uAQChkDVD15kBvj0PUt4hDpGq7ryfAsEfMnxlV2k4Ue6SKAEA3Smfd242lpPF
f89NNo6Y/ZhO+aWKfOLerXLfM6sB2QQ=
=cxvN
-----END PGP SIGNATURE-----
Merge tag 'for-5.15/parisc' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parisc architecture updates from Helge Deller:
- Fix a kernel crash when a signal is delivered to bad userspace stack
- Fix fall-through warnings in math-emu code
- Increase size of gcc stack frame check
- Switch coding from 'pci_' to 'dma_' API
- Make struct parisc_driver::remove() return void
- Some parisc related Makefile changes
- Minor cleanups, e.g. change to octal permissions, fix macro
collisions, fix PMD_ORDER collision, replace spaces with tabs
* tag 'for-5.15/parisc' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: math-emu: Fix fall-through warnings
parisc: fix crash with signals and alloca
parisc: Fix compile failure when building 64-bit kernel natively
parisc: ccio-dma.c: Added tab instead of spaces
parisc/parport_gsc: switch from 'pci_' to 'dma_' API
parisc: move core-y in arch/parisc/Makefile to arch/parisc/Kbuild
parisc: switch from 'pci_' to 'dma_' API
parisc: Make struct parisc_driver::remove() return void
parisc: remove unused arch/parisc/boot/install.sh and its phony target
parisc: Rename PMD_ORDER to PMD_TABLE_ORDER
parisc: math-emu: Avoid "fmt" macro collision
parisc: Increase size of gcc stack frame check
parisc: Replace symbolic permissions with octal permissions
The caller of this function (parisc_driver_remove() in
arch/parisc/kernel/drivers.c) ignores the return value, so better don't
return any value at all to not wake wrong expectations in driver authors.
The only function that could return a non-zero value before was
ipmi_parisc_remove() which returns the return value of
ipmi_si_remove_by_dev(). Make this function return void, too, as for all
other callers the value is ignored, too.
Also fold in a small checkpatch fix for:
WARNING: Unnecessary space before function pointer arguments
+ void (*remove) (struct parisc_device *dev);
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> (for drivers/input)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Helge Deller <deller@gmx.de>
read_poll_timeout was recently introduced, and can be used to simplify
our console polling loop. This results in a slight reduction in code.
early_uartlite_putc can't get the same treatment, because it can be
called before udelay is set up.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210826192549.3203071-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the constants defined at the beginning of this file instead of
integer literals when accessing registers. This makes this code easier
to read, and obviates the need for some explanatory comments.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20210826194323.3209227-1-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve OF match data, it's better and cleaner to use
'of_device_get_match_data' over 'of_match_device'.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210822032806.3256-4-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve OF match data, it's better and cleaner to use
'of_device_get_match_data' over 'of_match_device'.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210822032806.3256-3-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Retrieve OF match data, it's better and cleaner to use
'of_device_get_match_data' over 'of_match_device'.
Acked-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210822032806.3256-2-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function uart_add_one_port(), it can return zero or non-zero,
so remove redundant check to simplify the code.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210823110754.11232-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do software reset for communication port on imx7ulp and imx8qxp after
the port is registered if the UART controller support the feature.
Do partition reset with LPUART's power on, LPUART registers will
keep the previous status, like on i.MX8QXP platform, which is not
expected action, so need to set the RST bit of GLOBAL register to reset
all uart internal logic and registers.
Currently, only i.MX7ULP and i.MX8QXP LPUART controllers include
global register that support the software reset.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210823091801.17447-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add two stop bits support.
User can run the command to enable two stop bits for test:
stty cstopb -F /dev/ttyLPx
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210823081733.31941-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register offset needs to be applied on mapbase also.
dma_tx/rx_request use the physical address of UARTDATA.
Register offset is currently only applied to membase (the
corresponding virtual addr) but not on mapbase.
Fixes: 24b1e5f0e8 ("tty: serial: lpuart: add imx7ulp support")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Adriana Reus <adriana.reus@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Andy Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20210819021033.32606-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There have a corner case that tx DMA .callback() is coming after
.flush_buffer(), then .callback() should check dma_tx_in_progress
flag and return in directly.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Vipul Kumar <vipul_kumar@mentor.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210817100203.21300-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes two issues that cause the sysrq sequence to be inadvertently
aborted on SCIF serial consoles:
- a NUL character remains in the RX queue after a break has been detected,
which is then passed on to uart_handle_sysrq_char()
- the break interrupt is handled twice on controllers with multiplexed ERI
and BRI interrupts
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the defined variable 'dev' to make the code cleaner.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210814124951.30084-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b0819465be which
results in amba_device-specific code being called from
sbsa_uart_startup() and sbsa_uart_shutdown().
Signed-off-by: Qian Cai <quic_qiancai@quicinc.com>
Link: https://lore.kernel.org/r/20210813163135.205-1-quic_qiancai@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial driver data for Exynos850 SoC. This driver data is basically
reusing EXYNOS_COMMON_SERIAL_DRV_DATA, which is common for all Exynos
chips, but also enables USI init, which was added in previous commit:
"tty: serial: samsung: Init USI to keep clocks running".
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20210811114827.27322-7-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make checkpatch happy by fixing this error:
ERROR: Macros with complex values should be enclosed in parentheses
Although this change is made to keep macros consistent with consequent
patches (adding driver data for new SoC), it's intentionally added as a
separate patch to ease possible porting efforts in future.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20210811114827.27322-6-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART block is a part of USI (Universal Serial Interface) IP-core in
Samsung SoCs since Exynos9810 (e.g. in Exynos850). USI allows one to
enable one of three types of serial interface: UART, SPI or I2C. That's
possible because USI shares almost all internal circuits within each
protocol. USI also provides some additional registers so it's possible
to configure it.
One USI register called USI_OPTION has reset value of 0x0. Because of
this the clock gating behavior is controlled by hardware (HWACG =
Hardware Auto Clock Gating), which simply means the serial won't work
after reset as is. In order to make it work, USI_OPTION[2:1] bits must
be set to 0b01, so that HWACG is controlled manually (by software).
Bits meaning:
- CLKREQ_ON = 1: clock is continuously provided to IP
- CLKSTOP_ON = 0: drive IP_CLKREQ to High (needs to be set along with
CLKREQ_ON = 1)
USI is not present on older chips, like s3c2410, s3c2412, s3c2440,
s3c6400, s5pv210, exynos5433, exynos4210. So the new boolean field
'.has_usi' was added to struct s3c24xx_uart_info. USI registers will be
only actually accessed when '.has_usi' field is set to "1".
This feature is needed for further serial enablement on Exynos850, but
some other new Exynos chips (like Exynos9810) may benefit from this
feature as well.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20210811114827.27322-5-semen.protsenko@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the function stm32_usart_init_port, intent of the code maybe when
irq returns a value of zero, the return should be '-ENODEV'. But the
conditional expression '? :' maybe clerical error, it should be
'?:' to make '-ENODEV' work.
But in fact, as the example in platform.c is
* int irq = platform_get_irq(pdev, 0);
* if (irq < 0)
* return irq;
So the return value of zero is unnecessary to check, at last remove
the unnecessary '?: -ENODEV'.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210811105136.25392-1-tangbin@cmss.chinamobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle optional overrun-throttle-ms property as done for 8250_fsl in commit
6d7f677a2a ("serial: 8250: Rate limit serial port rx interrupts during
input overruns"). This can be used to rate limit the UART interrupts on
noisy lines that end up producing messages like the following:
ttyS ttyS2: 4 input overrun(s)
At least on droid4, the multiplexed USB and UART port is left to UART mode
by the bootloader for a debug console, and if a USB charger is connected
on boot, we get noise on the UART until the PMIC related drivers for PHY
and charger are loaded.
With this patch and overrun-throttle-ms = <500> we avoid the extra rx
interrupts.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103533.51547-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This attempts to fix a bug found with a serial port card which uses
an MCS9922 chip, one of the 4 models for which MSI-X interrupts are
currently supported. I don't possess such a card, and i'm not
experienced with the serial subsystem, so this patch is based on what
i think i found as a likely reason for failure, based on walking the
user who actually owns the card through some diagnostic.
The user who reported the problem finds the following in his dmesg
output for the relevant ttyS4 and ttyS5:
[ 0.580425] serial 0000:02:00.0: enabling device (0000 -> 0003)
[ 0.601448] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 125, base_baud = 115200) is a ST16650V2
[ 0.603089] serial 0000:02:00.1: enabling device (0000 -> 0003)
[ 0.624119] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 126, base_baud = 115200) is a ST16650V2
...
[ 6.323784] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
[ 6.324128] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
...
Output of setserial -a:
/dev/ttyS4, Line 4, UART: 16650V2, Port: 0x3010, IRQ: 127
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000
Flags: spd_normal skip_test
This suggests to me that the serial driver wants to register and share a
MSI/MSI-X irq 128 with the xhci_hcd driver, whereas the xhci driver does
not want to share the irq, as flags 0x00000080 (== IRQF_SHARED) from the
serial port driver means to share the irq, and this mismatch ends in some
failed irq init?
With this setup, data reception works very unreliable, with dropped data,
already at a transmission rate of only a 16 Bytes chunk every 1/120th of
a second, ie. 1920 Bytes/sec, presumably due to rx fifo overflow due to
mishandled or not used at all rx irq's?
See full discussion thread with attempted diagnosis at:
https://psychtoolbox.discourse.group/t/issues-with-iscan-serial-port-recording/3886
Disabling the use of MSI interrupts for the serial port pci card did
fix the reliability problems. The user executed the following sequence
of commands to achieve this:
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.0/msi_bus
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.1/msi_bus
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/bind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/bind
This resulted in the following log output:
[ 82.179021] pci 0000:02:00.0: MSI/MSI-X disallowed for future drivers
[ 87.003031] pci 0000:02:00.1: MSI/MSI-X disallowed for future drivers
[ 98.537010] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 17, base_baud = 115200) is a ST16650V2
[ 103.648124] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 18, base_baud = 115200) is a ST16650V2
This patch attempts to fix the problem by disabling irq sharing when
using MSI irq's. Note that all i know for sure is that disabling MSI
irq's fixed the problem for the user, so this patch could be wrong and
is untested. Please review with caution, keeping this in mind.
Fixes: 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
Cc: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: https://lore.kernel.org/r/20210729043306.18528-1-mario.kleiner.de@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix uart corruption issue when rx power off.
Add spin lock in mtk8250_dma_rx_complete function in APDMA mode.
when uart is used as a communication port with external device(GPS).
when external device(GPS) power off, the power of rx pin is also from
1.8v to 0v. Even if there is not any data in rx. But uart rx pin can
capture the data "0".
If uart don't receive any data in specified cycle, uart will generates
BI(Break interrupt) interrupt.
If external device(GPS) power off, we found that BI interrupt appeared
continuously and very frequently.
When uart interrupt type is BI, uart IRQ handler(8250 framwork
API:serial8250_handle_irq) will push data to tty buffer.
mtk8250_dma_rx_complete is a task of mtk_uart_apdma_rx_handler.
mtk8250_dma_rx_complete priority is lower than uart irq
handler(serial8250_handle_irq).
if we are in process of mtk8250_dma_rx_complete, uart appear BI
interrupt:1)serial8250_handle_irq will priority execution.2)it may cause
write tty buffer conflict in mtk8250_dma_rx_complete.
So the spin lock protect the rx receive data process is not break.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210729084640.17613-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch e60c2991f1 make the lpuart32_get_mctrl always return 0, actually
this will break the functions of device which use flow control such as
Bluetooth.
For lpuart32 plaform, the hardware can handle the CTS automatically.
So we should set TIOCM_CTS active. Also need to set CAR and DSR active.
Patch has been tested on lpuart32 platforms such as imx8qm and imx8ulp.
Fixes: e60c2991f1 ("serial: fsl_lpuart: remove RTSCTS handling from get_mctrl()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210729083109.31541-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For years we've been carrying legacy omap-serial in addition to
8250_omap driver and 8250_omap should be used instead.
Let's finally start planning on removing omap-serial by first not
building it if 8250_omap is selected to save some memory.
The defconfigs have switched over to using 8250_omap, and we have
a fixup in place for the the serial console since commit 00648d0282
("tty: serial: 8250: omap: add ttySx console if the user didn't").
So people updating their systems without omap-serial will see
boot time warnings on what is going on.
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Dario Binacchi <dariobin@libero.it>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103149.51175-2-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to remove the use of pm_runtime_irq_safe() from serial drivers
to allow making PM runtime handling generic. Let's simplify things by
disabling PM runtime autoidle for omap-serial as this driver has been
deprecated for years because of the 8250_omap driver.
There are still some omap-serial users that seem to hang on to it for
some unknown rs485 reasons it seems. But presumably those folks do not
need PM runtime autoidle with omap-serial, and hopefully can just move
to using 8250_omap driver instead.
For 8250_omap driver, we will eventually move to use generic serial
layer PM based on patches done by Andy Shevchenko to remove
pm_runtime_irq_safe() usage.
Cc: Andy Shevchenko <andriy.shevchenko@intel.com>
Cc: Dario Binacchi <dariobin@libero.it>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210727103149.51175-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bar and offset parameters to setup_port() are used in pointer math,
and while it would be very difficult to get them to wrap as a negative
number, just be "safe" and make them unsigned so that static checkers do
not trip over them unintentionally.
Cc: Jiri Slaby <jirislaby@kernel.org>
Reported-by: Jordy Zomer <jordy@pwning.systems>
Link: https://lore.kernel.org/r/20210726130717.2052096-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
put_tty_driver() is an alias for tty_driver_kref_put(). There is no need
for two exported identical functions, therefore switch all users of
old put_tty_driver() to new tty_driver_kref_put() and remove the former
for good.
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_tty_driver was deprecated by tty_alloc_driver in commit
7f0bc6a68e (TTY: pass flags to alloc_tty_driver) in 2012.
I never got into eliminating alloc_tty_driver until now. So we still
have two functions for allocating drivers which might be confusing. So
get rid of alloc_tty_driver uses to eliminate it for good in the next
patch.
Note we need to switch return value checking as tty_alloc_driver uses
ERR_PTR. And flags are now a parameter of tty_alloc_driver.
Cc: Richard Henderson <rth@twiddle.net>(odd fixer:ALPHA PORT)
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Samuel Iglesias Gonsalvez <siglesias@igalia.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Johan Hovold <johan@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210723074317.32690-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dennis reported that on ACPI-based systems the clock frequency
isn't enough to configure device properly. We have to respect
the clock source as well. To achieve this match the clock-names
property against "osc" to recognize external clock connection.
On DT-based system this doesn't change anything.
Reported-and-tested-by: Dennis Giaya <dgiaya@whoi.edu>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210723125943.22039-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oxford Semiconductor 950 serial port devices have a 128-byte FIFO and in
the enhanced (650) mode, which we select in `autoconfig_has_efr' with
the ECB bit set in the EFR register, they support the receive interrupt
trigger level selectable with FCR bits 7:6 from the set of 16, 32, 112,
120. This applies to the original OX16C950 discrete UART[1] as well as
950 cores embedded into more complex devices.
For these devices we set the default to 112, which sets an excessively
high level of 112 or 7/8 of the FIFO capacity, unlike with other port
types where we choose at most 1/2 of their respective FIFO capacities.
Additionally we don't make the trigger level configurable. Consequently
frequent input overruns happen with high bit rates where hardware flow
control cannot be used (e.g. terminal applications) even with otherwise
highly-performant systems.
Lower the default receive interrupt trigger level to 32 then, and make
it configurable. Document the trigger levels along with other port
types, including the set of 16, 32, 64, 112 for the transmit interrupt
as well[2].
References:
[1] "OX16C950 rev B High Performance UART with 128 byte FIFOs", Oxford
Semiconductor, Inc., DS-0031, Sep 05, Table 10: "Receiver Trigger
Levels", p. 22
[2] same, Table 9: "Transmit Interrupt Trigger Levels", p. 22
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260608480.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Elkhart Lake UARTs are PCI enumerated Synopsys DesignWare v4.0+ UART
integrated with Intel iDMA 32-bit DMA controller. There is a specific
driver to handle them, i.e. 8250_lpss. Hence, disable 8250_pci
enumeration for these UARTs.
Fixes: 1b91d97c66 ("serial: 8250_lpss: Add ->setup() for Elkhart Lake ports")
Fixes: 4f912b898d ("serial: 8250_lpss: Enable HS UART on Elkhart Lake")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210713101739.36962-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Add back an irqrestore-version of the sysrq port-unlock helper and use
it in the 8250 callbacks that need it.
Fixes: 75f4e830fa ("serial: do not restore interrupt state in sysrq helper")
Cc: stable@vger.kernel.org # 5.13
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210714080427.28164-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra serial driver always prints an error message when enabling the
FIFO for devices that have support for checking the FIFO enable status.
Fix this by displaying the error message, only when an error occurs.
Finally, update the error message to make it clear that enabling the
FIFO failed and display the error code.
Fixes: 222dcdff34 ("serial: tegra: check for FIFO mode enabled status")
Cc: <stable@vger.kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210630125643.264264-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In one error case the clock may be left prepared and enabled.
Unprepare and disable clock in that case to balance state of
the hardware.
Fixes: d4d6f03c4f ("serial: max310x: Try to get crystal clock rate from property")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210625153733.12911-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For the sake of reducing layering violation add ->unregister_gpio()
callback and use it in the ->exit() one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210713095821.7834-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the commit 07e5d4ff12 ("Revert serial-uartlite: Add runtime
support") the runtime pm support was reverted to aid reverting of
the other patches.
This patch adds the runtime PM support back.
The runtime pm calls are used to gate and enable the clocks.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/20210713064835.27978-3-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case the uart registration fails the clocks are left enabled.
Disable the clock in case of errors.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Link: https://lore.kernel.org/r/20210713064835.27978-2-shubhrajyoti.datta@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When DMA is used for TX and RX by serial driver, it should
pass the DMA device pointer to DMA API instead of UART device
pointer. DMA device should be used for DMA API because only
the DMA device is aware of how the device connects to the memory.
There might be an extra level of address translation due to a
SMMU attached to the DMA device. When serial device is used for
DMA API, the DMA API will have no clue of the SMMU attached to
the DMA device.
This patch is necessary to fix the SMMU page faults
which is observed when a DMA(with SMMU enabled) is attached
to UART for transfer.
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Link: https://lore.kernel.org/r/20210629045902.48912-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to make pl011 work better, multiple interrupts are
required, such as TXIM, RXIM, RTIM, error interrupt(FE/PE/BE/OE);
at the same time, pl011 to GIC does not merge the interrupt
lines(each serial-interrupt corresponding to different GIC hardware
interrupt), so need to enable and request multiple gic interrupt
numbers in the driver.
Signed-off-by: Bing Fan <tombinfan@tencent.com>
Link: https://lore.kernel.org/r/1625103512-30182-1-git-send-email-hptsfb@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add basic support for RS485: Provide a callback to configure RS485
settings. Handle the RS485 specific part in the functions
pl011_rs485_tx_start() and pl011_rs485_tx_stop() which extend the generic
start/stop callbacks.
Beside via IOCTL from userspace RS485 can be enabled by means of the
device tree property "rs485-enabled-at-boot-time".
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20210630225644.3744-1-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Report extra baud rates supported above the base rate for ports with the
UPF_MAGIC_MULTIPLIER property, so that people have a way to find out
that they can be used with their system, e.g.:
Serial: 8250/16550 driver, 5 ports, IRQ sharing enabled
printk: console [ttyS0] disabled
serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
serial8250.0: ttyS0 extra baud rates supported: 230400, 460800
printk: console [ttyS0] enabled
printk: bootconsole [uart8250] disabled
serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
serial8250.0: ttyS1 extra baud rates supported: 230400, 460800
serial8250.0: ttyS2 at MMIO 0x1f000900 (irq = 20, base_baud = 230400) is a 16550A
Otherwise there is no clear way to figure this out, as the feature is
only reported as an obscure TTY flag in bit 16:
$ cat /sys/class/tty/ttyS[0-2]/flags
0x10010040
0x10010040
0x90000040
$
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260334170.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allow more drivers to be compile tested more easily, for example, when
doing subsystem-wide changes.
Verified on X86_64 as well as arm, powerpc and m68k with minimal configs
in order to catch missing implicit build dependencies.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210715083011.18887-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pointer membase is currently being in initialized with zero rather
than NULL. Fix this.
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210719095533.14017-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ACPI-based Loongson boards need configurable rather than fixed clock
frequency for serial ports.
Signed-off-by: Jianmin Lv <lvjianmin@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
Link: https://lore.kernel.org/r/20210715061637.134436-1-chenhuacai@loongson.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't populate the const array k3_soc_devices on the stack but instead it
static. Makes the object code smaller by 44 bytes:
Before:
text data bss dec hex filename
31628 5609 128 37365 91f5 drivers/tty/serial/8250/8250_omap.o
After:
text data bss dec hex filename
31520 5673 128 37321 91c9 drivers/tty/serial/8250/8250_omap.o
Reduction of 44 bytes
(gcc version 10.3.0)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210715140759.27244-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups. Highlights
are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM4qQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylKvQCfbh+OmTkDlDlDhSWlxuV05M1XTXoAoLUcLZru
s5JCnwSZztQQLMDHj7Pd
=Zupm
-----END PGP SIGNATURE-----
Merge tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
Member nb in struct mvebu_uart is not set nor read. So remove it completely.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210624224909.6350-7-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For default (x16) scheme which is currently used by mvebu-uart.c driver,
maximal divisor of UART base clock is 1023*16. Therefore there is limit for
minimal supported baudrate. This change calculate it correctly and prevents
setting invalid divisor 0 into hardware registers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7d ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-4-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Testing mvuart->clk for non-error is not enough as mvuart->clk may contain
valid clk pointer but when clk_prepare_enable(mvuart->clk) failed then
port->uartclk is zero.
When mvuart->clk is not available then port->uartclk is zero too.
Parent clock rate port->uartclk is needed to calculate UART clock divisor
and without it is not possible to change baudrate.
So fix test condition when it is possible to change baudrate.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7d ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-3-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix checkpatch warnings:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Jinchao Wang <wjc@cdjrlc.com>
Link: https://lore.kernel.org/r/20210624021207.58059-1-wjc@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On K3 family of SoCs (which includes AM654 SoC), it is observed that RX
TIMEOUT is signalled after RX FIFO has been drained, in which case a
dummy read of RX FIFO is required to clear RX TIMEOUT condition.
Otherwise, this would lead to an interrupt storm.
Fix this by introducing UART_RX_TIMEOUT_QUIRK flag and doing a dummy
read in IRQ handler when RX TIMEOUT is reported with no data in RX FIFO.
Fixes: be70874498 ("serial: 8250_omap: Add support for AM654 UART controller")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210622145704.11168-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b61c8bf469. It never
made it to a public mailing list and still needs some work based on the
review comments. So revert it for now.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/CAMuHMdXA9-ajoAza2JAW5879ECieMm1dbBbKHgJhDa7=3kWu3w@mail.gmail.com
Cc: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GLOBETROTTER.cis entry in serial_cs matches more devices than
intended and breaks them. Remove it.
Example: # pccardctl info
PRODID_1="Option International
"
PRODID_2="GSM-Ready 56K/ISDN
"
PRODID_3="021
"
PRODID_4="A
"
MANFID=0013,0000
FUNCID=0
result:
pcmcia 0.0: Direct firmware load for cis/GLOBETROTTER.cis failed with error -2
The GLOBETROTTER.cis is nowhere to be found. There's GLOBETROTTER.cis.ihex at
https://netdev.vger.kernel.narkive.com/h4inqdxM/patch-axnet-cs-fix-phy-id-detection-for-bogus-asix-chip#post41
It's from completely diffetent card:
vers_1 4.1, "Option International", "GSM/GPRS GlobeTrotter", "001", "A"
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210611201940.23898-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle custom baud rates requested in the UPF_MAGIC_MULTIPLIER range
with BOTHER. Currently matching is exact, that is if a baud rate that
is not either of clk/4 or clk/8 is requested, then we fall through to
the default case, which will just divide the clock rate by 16 times the
rate requested, round it to closest integer, and possibly yield even
worse results then if clamping to the extra baud rates was chosen.
So for example if we have the usual base rate of 115200 and request a
rate of 230399, then the fall-through divisor calculation will yield 1,
and consequently the baud rate of 115200 will be programmed even though
obviously the magic rate of 230400 would be more appropriate.
Make the selection of the magic rates range-qualified then and use clk/4
for rates from clk/6 up (assuming `serial8250_get_baud_rate' has already
rejected any rates too far beyond clk/4), and otherwise use clk/8 for
rates from clk/12 up, and finally fall through to the standard divisor
calculation. Explicitly void using the undocumented rate of 153600bps
and stick to documented divisor values only.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105200232090.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support for magic baud rate divisors of 32770 and 32769 used with SMSC
Super I/O chips for extra baud rates of 230400 and 460800 respectively
where base rate is 115200[1] has been added around Linux 2.5.64, which
predates our repo history, but the origin could be identified as commit
2a717aad772f ("Merge with Linux 2.5.64.") with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>.
Code that is now in `serial8250_do_get_divisor' was added back then to
`serial8250_get_divisor', but that code would only ever trigger if one
of the higher baud rates was actually requested, and that cannot ever
happen, because the earlier call to `serial8250_get_baud_rate' never
returns them. This is because it calls `uart_get_baud_rate' with the
maximum requested being the base rate, that is clk/16 or 115200 for SMSC
chips at their nominal clock rate.
Fix it then and allow UPF_MAGIC_MULTIPLIER baud rates to be selected, by
requesting the maximum baud rate of clk/4 rather than clk/16 if the flag
has been set. Also correct the minimum baud rate, observing that these
ports only support actual (non-magic) divisors of up to 32767 only.
References:
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Table 31 - "Baud Rates", p. 77
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105190412280.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Contrary to what SMSC documentation says and unlike NS16C550A UARTs the
SMSC Super I/O IC claims compatibility with the SMSC UART implementation
does not support dividing the internal PLL clock by any divisor from 1
to 65535[1], with the exception of two magic divisors of 32769 and 32770
used respectively to select the high-speed data rates of 460800bps and
230400bps[2] if enabled on a port-by-port basis in with the Serial Port
Mode Register in the Device Configuration Space[3][4].
Instead empirical evidence indicates that the divisor, as stored in the
DLL and DLM register pair, has the range of 1 to 32767 only, and bit 7
of the DLM register (bit 15 of the divisor) effectively serves as a
selection bit for the prescaler from the base frequency of 7.3728MHz,
either 4 if the bit is 0, or 1 if the bit is 1 and high-speed operation
has been enabled with the Serial Port Mode Register.
So if high-speed operation has not been enabled, then say the values of
1 and 32769 (0x8001) written into the combined DLL and DLM register pair
both select the divisor of 1 and the baud rate of 115200bps.
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Section "Programmable Baud Rate Generator (and Divisor
Latches DLH, DLL)", p. 75
[2] same, Table 31 - "Baud Rates", p. 77
[3] same, Table 60 - "Serial Port 1, Logical Device 4 [Logical Device
Number = 0x04]", p. 153
[4] same, Table 61 - "Serial Port 2, Logical Device 5 [Logical Device
Number = 0x05]", p. 153
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106092330530.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oxford Semiconductor PCIe (Tornado) serial port devices are driven by a
fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.
In the enhanced (650) mode, which we select in `autoconfig_has_efr' by
setting the ECB bit in the EFR register, and in the absence of clock
reconfiguration, which we currently don't do, the clock rate is divided
only by the oversampling rate of 16 as it is supplied to the baud rate
generator, yielding the baud base of 3906250. This comes from the reset
values of the TCR and MCR[7] registers which are both zero[1][2][3][4],
choosing the oversampling rate of 16 and the normal (divide by 1) baud
rate generator prescaler respectively. This is the rate that is divided
by the value held in the divisor latch to determine the baud rate used.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then.
References:
[1] "OXPCIe200 PCI Express Multi-Port Bridge", Oxford Semiconductor,
Inc., DS-0045, 10 Nov 2008, Section "Reset Configuration", p. 72
[2] "OXPCIe952 PCI Express Bridge to Dual Serial & Parallel Port",
Oxford Semiconductor, Inc., DS-0046, Mar 06 08, Section "Reset
Configuration", p. 27
[3] "OXPCIe954 PCI Express Bridge to Quad Serial Port", Oxford
Semiconductor, Inc., DS-0047, Feb 08, Section "Reset Configuration",
p. 28
[4] "OXPCIe958 PCI Express Bridge to Octal Serial Port", Oxford
Semiconductor, Inc., DS-0048, Feb 08, Section "Reset Configuration",
p. 28
Fixes: 7106b4e333 ("8250: Oxford Semiconductor Devices")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106100203510.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Oxford Semiconductor PCIe (Tornado) serial port devices have their baud
base set incorrectly, however their `pciserial_board' entries have been
reused for Titan serial port devices. Define own entries for the latter
devices then, carrying over the settings, so that Oxford entries can be
fixed.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106100142310.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the previous patch, we introduced tty_get_char_size() and
tty_get_frame_size() for computing character and frame sizes,
respectively. Here, we make use of them in various tty drivers where
applicable.
The stats look nice: 12 insertions, 169 deletions.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Oliver Neukum <oneukum@suse.com>
Acked-by: Alex Elder <elder@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's a bit illogical to take magic constants in AUART_LINECTRL_WLEN.
Like in auart_console_get_options(), 2 means 7 bits. Switch
AUART_LINECTRL_WLEN to accept bit length, i.e. let it subtract 5 from
the parameter before doing the logic.
This will ease conversion from CSIZE to bits in mxs_auart_settermios()
in the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many tty drivers contain code to compute bits count depending on termios
cflags. So extract this code from serial core to two separate tty helper
functions:
* tty_get_char_size -- only size of a character, without flags,
* tty_get_frame_size -- complete size of a frame including flags.
In the next patch, calls to these new functions replace many copies of
this code.
Note that we accept only cflag as a parameter. That's because some
callers like pch_uart_startup or sunsab_console_setup don't have at hand
termios which we could pass around.
Cc: Joe Perches <joe@perches.com>
Cc: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Defer device probe operation when a DMA channel request probe deferral.
With this change both DMA channels are acquired before DMA channels are
configured. Once no probe deferral is expected, DMAs are
configured and any failure in their configuration will make the driver
to fallback to interrupt mode as prior this change.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Link: https://lore.kernel.org/r/20210610100020.2318-1-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Request the RX mailbox only after initializing the UART data
structures. Otherwise it can rarely happen that the receive
callback is called before the UART is ready.
Fixes: 2d908b38d4 ("serial: Add Tegra Combined UART driver")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://lore.kernel.org/r/20210609155655.3567545-1-mperttunen@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following
message is possible output when system enters suspend and while
transferring data, because clearing TIE bit in SCSCR is not able to
stop any dmaengine transfer.
sh-sci e6550000.serial: ttySC1: Unable to drain transmitter
Note that this driver has already used some #ifdef in the .c file
so that this patch also uses #ifdef to fix the issue. Otherwise,
build errors happens if the CONFIG_SERIAL_SH_SCI_DMA is disabled.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210610110806.277932-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into tty-next
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmDGe+4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiG/IUH/iyHVulAtAhL9bnR
qL4M1kWfcG1sKS2TzGRZzo6YiUABf89vFP90r4sKxG3AKrb8YkTwmJr8B/sWwcsv
PpKkXXTobbDfpSrsXGEapBkQOE7h2w739XeXyBLRPkoCR4UrEFn68TV2rLjMLBPS
/EIZkonXLWzzWalgKDP4wSJ7GaQxi3LMx3dGAvbFArEGZ1mPHNlgWy2VokFY/yBf
qh1EZ5rugysc78JCpTqfTf3fUPK2idQW5gtHSMbyESrWwJ/3XXL9o1ET3JWURYf1
b0FgVztzddwgULoIGWLxDH5WWts3l54sjBLj0yrLUlnGKA5FjrZb12g9PdhdywuY
/8KfjeE=
=JfJm
-----END PGP SIGNATURE-----
Merge tag 'v5.13-rc6' into driver-core-next
We need the driver core fix in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We would like to use DMI matching in other functions as well.
Hence, extract it as exar_get_platform() helper function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210608144239.12697-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's possible that during ->exit() the private_data is NULL,
for instance when there was no GPIO device instantiated.
Due to this we may not dereference it. Add a respective check.
Note, for now ->exit() only makes sense when GPIO device
was instantiated, that's why we may use the check for entire
function.
Fixes: 81171e7d31 ("serial: 8250_exar: Constify the software nodes")
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20210608144239.12697-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add serial support for RZ/G2L SoC with earlycon and
extended mode register support.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210603221758.10305-11-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the hack to assign the global console_port variable at probe time.
This assumption that cons->index is -1 is wrong for systems that specify
'console=' in the cmdline (or 'stdout-path' in dts). Hence, on such system
the actual console assignment is ignored, and the first UART that happens
to be probed is used as console instead.
Move the logic to console_setup() and map the console to the correct port
through the array of available ports instead.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20210528133321.1859346-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to optimize serial communication (performance/throughput VS
latency), we may need to tweak DMA period number and size. This adds
DT properties to configure those values before initialising DMA.
The defaults will stay the same as before.
[update documentation and commit message, rebase to current master,
switch back to DT instead of sysfs]
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210430175038.103226-2-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are some small fixes for reported problems for tty and serial
drivers for 5.13-rc4.
They consist of:
- 8250 bugfixes and new device support
- lockdown security mode fixup
- syzbot found problems fixed
- 8250_omap fix for interrupt storm
- revert of 8250_omap driver fix as it caused worse problem than
the original issue
All but the last patch have been in linux-next for a while, the last one
is a revert of a problem found in linux-next with the 8250_omap driver
change.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYLJODQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yna7gCgmKIssymva29JpQb54HuzRooD8jcAn3XeMVWI
E4TQzaTFC1mNAQy8GU4F
=cLjq
-----END PGP SIGNATURE-----
Merge tag 'tty-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver fixes from Greg KH:
"Here are some small fixes for reported problems for tty and serial
drivers for 5.13-rc4.
They consist of:
- 8250 bugfixes and new device support
- lockdown security mode fixup
- syzbot found problems fixed
- 8250_omap fix for interrupt storm
- revert of 8250_omap driver fix as it caused worse problem than the
original issue
All but the last patch have been in linux-next for a while, the last
one is a revert of a problem found in linux-next with the 8250_omap
driver change"
* tag 'tty-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250: 8250_omap: Fix possible interrupt storm"
serial: 8250_pci: handle FL_NOIRQ board flag
serial: rp2: use 'request_firmware' instead of 'request_firmware_nowait'
serial: 8250_pci: Add support for new HPE serial device
serial: 8250: 8250_omap: Fix possible interrupt storm
serial: 8250: Use BIT(x) for UART_{CAP,BUG}_*
serial: 8250: Add UART_BUG_TXRACE workaround for Aspeed VUART
serial: 8250_dw: Add device HID for new AMD UART controller
serial: sh-sci: Fix off-by-one error in FIFO threshold register setting
serial: core: fix suspicious security_locked_down() call
serial: tegra: Fix a mask operation that is always true
This reverts commit 31fae7c8b1.
Tony writes:
I just noticed this causes the following regression in Linux
next when pressing a key on uart console after boot at least on
omap3. This seems to happen on serial_port_in(port, UART_RX) in
the quirk handling.
So let's drop this.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/YLCCJzkkB4N7LTQS@atomide.com
Fixes: 31fae7c8b1 ("serial: 8250: 8250_omap: Fix possible interrupt storm")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
the way the irq gets allocated was changed. With that change the
handling FL_NOIRQ got lost. Restore the old behaviour.
Fixes: 8428413b1d ("serial: 8250_pci: Implement MSI(-X) support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Link: https://lore.kernel.org/r/20210527095529.26281-1-christian.gmeiner@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for new HPE serial device. It is MSI enabled,
but otherwise similar to legacy HP server serial devices.
Tested-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Randy Wright <rwright@hpe.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1621009614-28836-1-git-send-email-rwright@hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is possible that RX TIMEOUT is signalled after RX FIFO has been
drained, in which case a dummy read of RX FIFO is required to clear RX
TIMEOUT condition. Otherwise, RX TIMEOUT condition is not cleared
leading to an interrupt storm
Cc: stable@vger.kernel.org
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210511151955.28071-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Aspeed Virtual UARTs directly bridge e.g. the system console UART on the
LPC bus to the UART interface on the BMC's internal APB. As such there's
no RS-232 signalling involved - the UART interfaces on each bus are
directly connected as the producers and consumers of the one set of
FIFOs.
The APB in the AST2600 generally runs at 100MHz while the LPC bus peaks
at 33MHz. The difference in clock speeds exposes a race in the VUART
design where a Tx data burst on the APB interface can result in a byte
lost on the LPC interface. The symptom is LSR[DR] remains clear on the
LPC interface despite data being present in its Rx FIFO, while LSR[THRE]
remains clear on the APB interface as the host has not consumed the data
the BMC has transmitted. In this state, the UART has stalled and no
further data can be transmitted without manual intervention (e.g.
resetting the FIFOs, resulting in loss of data).
The recommended work-around is to insert a read cycle on the APB
interface between writes to THR.
Cc: ChiaWei Wang <chiawei_wang@aspeedtech.com>
Tested-by: ChiaWei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210520021334.497341-2-andrew@aj.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/st-asc.c:73: warning: expecting prototype for Some of status comes from higher bits of the character and some come from(). Prototype was for ASC_RXBUF_DUMMY_RX() instead
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210520121906.3468725-10-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the previous patch, we can make port passed to
serial8250_find_match_or_unused const. And then we can make const also
port of serial8250_register_8250_port.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210519072153.3859-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* make parameters const (as they are only read)
* return bool (as comparison results are returned)
* add \n before final return
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210519072153.3859-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most litex boards using RISC-V soft cores us the sbi earlycon, however
this is not available for non RISC-V litex SoC's. This patch enables
earlycon for liteuart which is available on all Litex SoC's making
support for earycon debugging more widely available.
Cc: Florent Kermarrec <florent@enjoy-digital.fr>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Gabriel L. Somlo <gsomlo@gmail.com>
Reviewed-and-tested-by: Gabriel Somlo <gsomlo@gmail.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Link: https://lore.kernel.org/r/20210517115453.24365-1-shorne@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
