We don't actually do the efx_mcdi_reset() because we don't have MCDI yet.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No TX or RX path, no MCDI, not even an ifup/down handler.
Besides stubs, the bulk of the patch deals with reading the Xilinx
extended PCIe capability, which tells us where to find our BAR.
Though in the same module, EF100 has its own struct pci_driver,
which is named sfc_ef100.
A small number of additional nic_type methods are added; those in the
TX (tx_enqueue) and RX (rx_packet) paths are called through indirect
call wrappers to minimise the performance impact.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EF100 adds a few new valid addresses for efx_writed_page(), as well as
a Function Control Window in the BAR whose location is variable.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An MDIO-based n-way restart does not make sense for any of the NICs
supported by this driver, nor for the coming EF100.
Unlike on Falcon (which was already split off into a separate driver),
the PHY on all of Siena, EF10 and EF100 is managed by MC firmware.
While Siena can talk to the PHY over MDIO, doing so for anything other
than debugging purposes (mdio_mii_ioctl) is likely to confuse the
firmware.
(According to the SFC firmware team, this support was originally added
to the Siena driver early in the development of that product, before
it was decided to have firmware manage the PHY.)
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Murali Karicheri says:
====================
Add PRP driver
This series is dependent on the following patches sent out to
netdev list. All (1-3) are already merged to net/master as of
sending this, but not on the net-next master branch. So need
to apply them to net-next before applying this series. v3 of
the iproute2 patches can be merged to work with this series
as there are no updates since then.
[1] https://marc.info/?l=linux-netdev&m=159526378131542&w=2
[2] https://marc.info/?l=linux-netdev&m=159499772225350&w=2
[3] https://marc.info/?l=linux-netdev&m=159499772425352&w=2
This series adds support for Parallel Redundancy Protocol (PRP)
in the Linux HSR driver as defined in IEC-62439-3. PRP Uses a
Redundancy Control Trailer (RCT) the format of which is
similar to HSR Tag. This is used for implementing redundancy.
RCT consists of 6 bytes similar to HSR tag and contain following
fields:-
- 16-bit sequence number (SeqNr);
- 4-bit LAN identifier (LanId);
- 12 bit frame size (LSDUsize);
- 16-bit suffix (PRPsuffix).
The PRPsuffix identifies PRP frames and distinguishes PRP frames
from other protocols that also append a trailer to their useful
data. The LSDUsize field allows the receiver to distinguish PRP
frames from random, nonredundant frames as an additional check.
LSDUsize is the size of the Ethernet payload inclusive of the
RCT. Sequence number along with LanId is used for duplicate
detection and discard.
PRP node is also known as Dual Attached Node (DAN-P) since it
is typically attached to two different LAN for redundancy.
DAN-P duplicates each of L2 frames and send it over the two
Ethernet links. Each outgoing frame is appended with RCT.
Unlike HSR, these are added to the end of L2 frame and will be
treated as pad by bridges and therefore would be work with
traditional bridges or switches, where as HSR wouldn't as Tag
is prefixed to the Ethenet frame. At the remote end, these are
received and the duplicate frame is discarded before the stripped
frame is send up the networking stack. Like HSR, PRP also sends
periodic Supervision frames to the network. These frames are
received and MAC address from the SV frames are populated in a
database called Node Table. The above functions are grouped into
a block called Link Redundancy Entity (LRE) in the IEC spec.
As there are many similarities between HSR and PRP protocols,
this patch re-uses the code from HSR driver to implement PRP
driver. As per feedback from the RFC series, the implementation
uses the existing HSR Netlink socket interface to create the
PRP interface by adding a new proto parameter to the ip link
command to identify the PRP protocol. iproute2 is enhanced to
implement this new parameter. The hsr_netlink.c is enhanced
to handle the new proto parameter. As suggested during the RFC
review, the driver introduced a proto_ops structure to hold
protocol specfic functions to handle HSR and PRP specific
function pointers and use them in the code based on the
protocol to handle protocol specific part differently in the
driver.
Please review this and provide me feedback so that I can work to
incorporate them and spin the next version if needed.
The patch was tested using two TI AM57x IDK boards for PRP which
are connected back to back over two CPSW Ethernet ports.
PRP Test setup
---------------
--------eth0 eth0 --------
|AM572x|----------------------|AM572x|
| |----------------------| |
--------eth1 eth1 --------
To build, enable CONFIG_HSR=y or m
make omap2plus_defconfig
make zImage; make modules; make dtbs
Copy the zImage and dtb files to the file system on SD card
and power on the AM572x boards.
This can be tested on any platforms with 2 Ethernet interfaces.
So will appreciate if you can give it a try and provide your
Tested-by.
Command to create PRP interface
-------------------------------
ifconfig eth0 0.0.0.0 down
ifconfig eth1 0.0.0.0 down
ifconfig eth0 hw ether 70:FF:76:1C:0E:8C
ifconfig eth1 hw ether 70:FF:76:1C:0E:8C
ifconfig eth0 up
ifconfig eth1 up
ip link add name prp0 type hsr slave1 eth0 slave2 eth1 supervision 45 proto 1
ifconfig prp0 192.168.2.10
ifconfig eth0 0.0.0.0 down
ifconfig eth1 0.0.0.0 down
ifconfig eth0 hw ether 70:FF:76:1C:0E:8D
ifconfig eth1 hw ether 70:FF:76:1C:0E:8D
ifconfig eth0 up
ifconfig eth1 up
ip link add name prp0 type hsr slave1 eth0 slave2 eth1 supervision 45 proto 1
ifconfig prp0 192.168.2.20
command to show node table
----------------------------
Ping the peer board after the prp0 interface is up.
The remote node (DAN-P) will be shown in the node table as below.
root@am57xx-evm:~# cat /sys/kernel/debug/hsr/prp0/node_table
Node Table entries for (PRP) device
MAC-Address-A, MAC-Address-B, time_in[A], time_in[B], Address-B port, SAN-A, SAN-B, DAN-P
70:ff:76:1c:0e:8c 00:00:00:00:00:00 ffffe83f, ffffe83f, 0, 0, 0, 1
Try to capture the raw PRP frames at the eth0 interface as
tcpdump -i eth0 -xxx
Sample Supervision frames and ARP frames shown below.
==================================================================================
Successive Supervision frames captured with tcpdump (with RCT at the end):
03:43:29.500999 70:ff:76:1c:0e:8d (oui Unknown) > 01:15:4e:00:01:2d (oui Unknown), ethertype Unknown (0x88f
0x0000: 0115 4e00 012d 70ff 761c 0e8d 88fb 0001
0x0010: 7e0a 1406 70ff 761c 0e8d 0000 0000 0000
0x0020: 0000 0000 0000 0000 0000 0000 0000 0000
0x0030: 0000 0000 0000 0000 0000 0000 fc2b a034
0x0040: 88fb
03:43:31.581025 70:ff:76:1c:0e:8d (oui Unknown) > 01:15:4e:00:01:2d (oui Unknown), ethertype Unknown (0x88f
0x0000: 0115 4e00 012d 70ff 761c 0e8d 88fb 0001
0x0010: 7e0b 1406 70ff 761c 0e8d 0000 0000 0000
0x0020: 0000 0000 0000 0000 0000 0000 0000 0000
0x0030: 0000 0000 0000 0000 0000 0000 fc2c a034
0x0040: 88fb
ICMP Echo request frame with RCT
03:43:33.805354 IP 192.168.2.20 > 192.168.2.10: ICMP echo request, id 63748, seq 1, length 64
0x0000: 70ff 761c 0e8c 70ff 761c 0e8d 0800 4500
0x0010: 0054 26a4 4000 4001 8e96 c0a8 0214 c0a8
0x0020: 020a 0800 c28e f904 0001 202e 1c3d 0000
0x0030: 0000 0000 0000 0000 0000 0000 0000 0000
0x0040: 0000 0000 0000 0000 0000 0000 0000 0000
0x0050: 0000 0000 0000 0000 0000 0000 0000 0000
0x0060: 0000 fc31 a05a 88fb
==================================================================================
The iperf3 traffic test logs can be accessed at the links below.
DUT-1: https://pastebin.ubuntu.com/p/8SkQzWJMn8/
DUT-2: https://pastebin.ubuntu.com/p/j2BZvvs7p4/
Other tests done.
- Connect a SAN (eth0 and eth1 without prp interface) and
do ping test from eth0 (192.168.2.40) to prp0 (192.168.2.10)
verify the SAN node shows at the correct link A and B as shown
in the node table dump
- Regress HSR interface using 3 nodes connected in a ring topology.
create hsr link version 0. Do iperf3 test between all nodes
create hsr link version 1. Do iperf3 test between all nodes.
--------eth0 eth1 --------eth0 eth1-------|
|AM572x|----------------------|AM572x|--------------|AM572x|
| | | | ------| |
--------eth1---| ------- | eth0 -------
|-------------------------------
command used for HSR interface
HSR V0
ifconfig eth0 0.0.0.0 down
ifconfig eth1 0.0.0.0 down
ifconfig eth0 hw ether 70:FF:76:1C:0E:8C
ifconfig eth1 hw ether 70:FF:76:1C:0E:8C
ifconfig eth0 up
ifconfig eth1 up
ip link add name hsr0 type hsr slave1 eth0 slave2 eth1 supervision 45 version 0
ifconfig hsr0 192.168.2.10
HSR V1
ifconfig eth0 0.0.0.0 down
ifconfig eth1 0.0.0.0 down
ifconfig eth0 hw ether 70:FF:76:1C:0E:8C
ifconfig eth1 hw ether 70:FF:76:1C:0E:8C
ifconfig eth0 up
ifconfig eth1 up
ip link add name hsr0 type hsr slave1 eth0 slave2 eth1 supervision 45 version 1
ifconfig hsr0 192.168.2.10
Logs at
DUT-1 : https://pastebin.ubuntu.com/p/6PSJbZwQ6y/
DUT-2 : https://pastebin.ubuntu.com/p/T8TqJsPRHc/
DUT-3 : https://pastebin.ubuntu.com/p/VNzpv6HzKj/
- Build tests :-
Build with CONFIG_HSR=m
allmodconfig build
build with CONFIG_HSR=y and rebuild with sparse checker
make C=1 zImage; make modules
Version history:
v5 : Fixed comments about Kconfig changes on Patch 1/7 against v4
Rebased to netnext/master branch.
v4 : fixed following vs v3
reverse xmas tree for local variables
check for return type in call to skb_put_padto()
v3 : Separated bug fixes from this series and send them for immediate merge
But for that this is same as v2.
v2 : updated comments on RFC. Following are the main changes:-
- Removed the hsr_prp prefix
- Added PRP information in header files to indicate
the support for PRP explicitely
- Re-use netlink socket interface with an added
parameter proto for identifying PRP.
- Use function pointers using a proto_ops struct
to do things differently for PRP vs HSR.
RFC: initial version posted and discussed at
https://www.spinics.net/lists/netdev/msg656229.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Print PRP specific information from node table as part of debugfs
node table display. Also display the node as DAN-H or DAN-P depending
on the info from node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DAN-P (Dual Attached Nodes PRP) nodes are expected to receive
traditional IP packets as well as PRP (Parallel Redundancy
Protocol) tagged (trailer) packets. PRP trailer is 6 bytes
of PRP protocol unit called RCT, Redundancy Control Trailer
(RCT) similar to HSR tag. PRP network can have traditional
devices such as bridges/switches or PC attached to it and
should be able to communicate. Regular Ethernet devices treat
the RCT as pads. This patch adds logic to format L2 frames
from network stack to add a trailer (RCT) and send it as
duplicates over the slave interfaces when the protocol is
PRP as per IEC 62439-3. At the ingress, it strips the trailer,
do duplicate detection and rejection and forward a stripped
frame up the network stack. PRP device should accept frames
from Singly Attached Nodes (SAN) and thus the driver mark
the link where the frame came from in the node table.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP, refactor the code specific to
handling HSR frames into separate functions and call them through
proto_ops function pointers.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for generation of PRP supervision frames. For PRP,
supervision frame format is similar to HSR version 0, but have
a PRP Redundancy Control Trailer (RCT) added and uses a different
message type, PRP_TLV_LIFE_CHECK_DD. Also update
is_supervision_frame() to include the new message type used for
PRP supervision frame.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce support for PRP protocol, add a
protocol ops ptr in the private hsr structure to hold function
pointers as some of the functions at protocol level packet
handling is different for HSR vs PRP. It is expected that PRP will
add its of set of functions for protocol handling. Modify existing
hsr_announce() function to call proto_ops->send_sv_frame() to send
supervision frame for HSR. This is expected to be different for PRP.
So introduce a ops function ptr, send_sv_frame() for the same and
initialize it to send_hsr_supervsion_frame(). Modify hsr_announce()
to call proto_ops->send_sv_frame().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparatory patch to introduce PRP protocol support in the
driver, refactor the skb init code to a separate function.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Parallel Redundancy Protocol (PRP) is another redundancy protocol
introduced by IEC 63439 standard. It is similar to HSR in many
aspects:-
- Use a pair of Ethernet interfaces to created the PRP device
- Use a 6 byte redundancy protocol part (RCT, Redundancy Check
Trailer) similar to HSR Tag.
- Has Link Redundancy Entity (LRE) that works with RCT to implement
redundancy.
Key difference is that the protocol unit is a trailer instead of a
prefix as in HSR. That makes it inter-operable with tradition network
components such as bridges/switches which treat it as pad bytes,
whereas HSR nodes requires some kind of translators (Called redbox) to
talk to regular network devices. This features allows regular linux box
to be converted to a DAN-P box. DAN-P stands for Dual Attached Node - PRP
similar to DAN-H (Dual Attached Node - HSR).
Add a comment at the header/source code to explicitly state that the
driver files also handles PRP protocol as well.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan reports static checker warning:
"The patch 9b6ee3cf95: "qed: sanitize PBL chains allocation" from Jul
23, 2020, leads to the following static checker warning:
drivers/net/ethernet/qlogic/qed/qed_chain.c:299 qed_chain_alloc_pbl()
error: uninitialized symbol 'pbl_virt'.
drivers/net/ethernet/qlogic/qed/qed_chain.c
249 static int qed_chain_alloc_pbl(struct qed_dev *cdev, struct qed_chain *chain)
250 {
251 struct device *dev = &cdev->pdev->dev;
252 struct addr_tbl_entry *addr_tbl;
253 dma_addr_t phys, pbl_phys;
254 __le64 *pbl_virt;
^^^^^^^^^^^^^^^^
[...]
271 if (chain->b_external_pbl)
272 goto alloc_pages;
^^^^^^^^^^^^^^^^ uninitialized
[...]
298 /* Fill the PBL table with the physical address of the page */
299 pbl_virt[i] = cpu_to_le64(phys);
^^^^^^^^^^^
[...]
"
This issue was introduced with commit c3a321b06a ("qed: simplify
initialization of the chains with an external PBL"), when
chain->pbl_sp.table_virt initialization was moved up to
qed_chain_init_params().
Fix it by initializing pbl_virt with an already filled chain struct field.
Fixes: c3a321b06a ("qed: simplify initialization of the chains with an external PBL")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexander Lobakin <alobakin@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en update.
This patchset removes the PCIe histogram and other debug register
data from ethtool -S. The removed data are not counters and they have
very large and constantly fluctuating values that are not suitable for
the ethtool -S decimal counter display.
The rest of the patches implement counter rollover for all hardware
counters that are not 64-bit counters. Different generations of
hardware have different counter widths. The driver will now query
the counter widths of all counters from firmware and implement
rollover support on all non-64-bit counters.
The last patch adds the PCIe histogram and other PCIe register data back
using the ethtool -d interface.
v2: Fix bnxt_re RDMA driver compile issue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to dump PXP registers and PCIe statistics.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we can report all the full 64-bit CPU endian software accumulated
counters instead of the hw counters, some of which may be less than
64-bit wide. Define the necessary macros to access the software
counters.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have the infrastructure in place, add the new function
bnxt_accumulate_all_stats() to periodically accumulate and check for
counter rollover of all ring stats and port stats.
A chip bug was also discovered that could cause some ring counters to
become 0 during DMA. Workaround by ignoring zeros on the affected
chips.
Some older frimware will reset port counters during ifdown. We need
to check for that and free the accumulated port counters during ifdown
to prevent bogus counter overflow detection during ifup.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If supported by newer firmware, make the firmware call to query all
the port counter masks. If not supported, assume 40-bit port
counter masks.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware has a new call HWRM_FUNC_QSTATS_EXT to retrieve the
masks of all ring counters. Make this call when supported to
initialize the hardware masks of all ring counters. If the call
is not available, assume 48-bit ring counter masks on P5 chips.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of these DMAed hardware counters are not full 64-bit counters and
so we need to accumulate them as they overflow. Allocate copies of these
DMA statistics memory blocks with the same size for accumulation. The
hardware counter widths are also counter specific so we allocate
memory for masks that correspond to each counter.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver manages multiple statistics structures of different sizes.
They are all allocated, freed, and handled practically the same. Define
a new bnxt_stats_mem structure and common allocation and free functions
for all staistics memory blocks.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port statistics structures have hard coded padding and offset.
Define macros to make this look cleaner.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Main changes are 200G support and fixing the definitions of discard and
error counters to match the hardware definitions.
Because the HWRM_PORT_PHY_QCFG message size has now exceeded the max.
encapsulated response message size of 96 bytes from the PF to the VF,
we now need to cap this message to 96 bytes for forwarding. The forwarded
response only needs to contain the basic link status and speed information
and can be capped without adding the new information.
v2: Fix bnxt_re compile error.
Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove PCIe non-counters display from ethtool statistics, as
they are not simple counters but register dump. The next few
patches will add logic to detect counter roll-over and it won't
work with these PCIe non-counters.
There will be a follow up patch to get PCIe information via
ethtool register dump.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPLS has no dependency with the device type of underlying devices.
Hence the device type check to add mpls support for devices can be
avoided.
Signed-off-by: Martin Varghese <martin.varghese@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cited commit mistakenly copied provided option to 'val' instead of to
'mfc':
```
- if (copy_from_user(&mfc, optval, sizeof(mfc))) {
+ if (copy_from_sockptr(&val, optval, sizeof(val))) {
```
Fix this by copying the option to 'mfc'.
selftest router_multicast.sh before:
$ ./router_multicast.sh
smcroutectl: Unknown or malformed IPC message 'a' from client.
smcroutectl: failed removing multicast route, does not exist.
TEST: mcast IPv4 [FAIL]
Multicast not received on first host
TEST: mcast IPv6 [ OK ]
smcroutectl: Unknown or malformed IPC message 'a' from client.
smcroutectl: failed removing multicast route, does not exist.
TEST: RPF IPv4 [FAIL]
Multicast not received on first host
TEST: RPF IPv6 [ OK ]
selftest router_multicast.sh after:
$ ./router_multicast.sh
TEST: mcast IPv4 [ OK ]
TEST: mcast IPv6 [ OK ]
TEST: RPF IPv4 [ OK ]
TEST: RPF IPv6 [ OK ]
Fixes: 01ccb5b48f ("net/ipv4: switch ip_mroute_setsockopt to sockptr_t")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Karsten Graul says:
====================
net/smc: show unique rsn code for exceeded max dmb count
Resolve some confusion at the user side when the reason code shows
out-of-memory but actually there is enough memory left.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the maximum dmb buffer limit for an ism device is reached no more
dmb buffers can be registered. When this happens the reason code is set
to SMC_CLC_DECL_MEM indicating out-of-memory. This is the same reason
code that is used when no memory could be allocated for the new dmb
buffer.
This is confusing for users when they see this error but there is more
memory available. To solve this set a separate new reason code when the
maximum dmb limit exceeded.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ism driver allocates a new dmb in ism_alloc_dmb() it must
first check for and reserve a slot in the sba bitmap. When
find_next_zero_bit() finds no free slot then the return code is -ENOMEM.
This code conflicts with the error when the alloc() fails later in the
code. As a result of that the caller can not differentiate
between out-of-memory conditions and sba-bitmap-full conditions.
Fix that by using the return code -ENOSPC when the sba slot
reservation failed.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
list_for_each_safe is able to handle an empty list.
The only effect of avoiding the loop is not initializing the
index variable.
Drop list_empty tests in cases where these variables are not
used.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
<smpl>
@@
expression x,e;
iterator name list_for_each_safe;
statement S;
identifier i,j;
@@
-if (!(list_empty(x))) {
list_for_each_safe(i,j,x) S
- }
... when != i
when != j
(
i = e;
|
? j = e;
)
</smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/intel/igc/igc_mac.c:424 igc_check_for_copper_link()
error: uninitialized symbol 'link'.
This patch come to fix this warning and initialize the 'link' symbol.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 707abf0695 ("igc: Add initial LTR support")
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Remove ictxptc, ictxatc, cbtmpc, cbrdpc, cbrmpc and htcbdpc fields from
the hw_stats structure. Accordance to the i225 device
specification these fields not in use.
This patch come to clean up the driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
collision_delta, tx_packet_delta, txcw, adaptive_ifs and
has_fwsm fields not in use.
This patch come to clean up the driver code.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
LED control currently not implemented.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
IGC_ICTXPTC and IGC_ICTXATC are already defined elsewhere, remove this
double definition. Also, remove unneeded registers as they are not
applicable to i225 devices.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tx Queue Min Threshold Count register no applicable for the i225 device.
This patch comes to clean up it.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The statistics of this register are being tracked, however, the register
was inadvertently missed when implementing igc_clear_hw_cntrs_base().
The register is clear on read, so add it to the function so that the
register is cleared when requested so the tracked count is accurate.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Though we are populating and tracking ictxqec, the value is not being used
for anything so remove it altogether and save the register read.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
I have a few more fixes this week:
* A fix to avoid using SBI calls during kasan initialization, as the SBI calls
themselves have not been probed yet.
* Three fixes related to systems with multiple memory regions.
-----BEGIN PGP SIGNATURE-----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=FG/F
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-linus-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux into master
Pull RISC-V fixes from Palmer Dabbelt:
"A few more fixes this week:
- A fix to avoid using SBI calls during kasan initialization, as the
SBI calls themselves have not been probed yet.
- Three fixes related to systems with multiple memory regions"
* tag 'riscv-for-linus-5.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: Parse all memory blocks to remove unusable memory
RISC-V: Do not rely on initrd_start/end computed during early dt parsing
RISC-V: Set maximum number of mapped pages correctly
riscv: kasan: use local_tlb_flush_all() to avoid uninitialized __sbi_rfence
- Fix a section end page alignment assumption that was causing crashes
- Fix ORC unwinding on freshly forked tasks which haven't executed yet
and which have empty user task stacks
- Fix the debug.exception-trace=1 sysctl dumping of user stacks, which
was broken by recent maccess changes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=oamN
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master
Pull x86 fixes from Ingo Molnar:
"Misc fixes:
- Fix a section end page alignment assumption that was causing
crashes
- Fix ORC unwinding on freshly forked tasks which haven't executed
yet and which have empty user task stacks
- Fix the debug.exception-trace=1 sysctl dumping of user stacks,
which was broken by recent maccess changes"
* tag 'x86-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/dumpstack: Dump user space code correctly again
x86/stacktrace: Fix reliable check for empty user task stacks
x86/unwind/orc: Fix ORC for newly forked tasks
x86, vmlinux.lds: Page-align end of ..page_aligned sections
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=7P/h
-----END PGP SIGNATURE-----
Merge tag 'timers-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master
Pull timer fix from Ingo Molnar:
"Fix a suspend/resume regression (crash) on TI AM3/AM4 SoC's"
* tag 'timers-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/timer-ti-dm: Fix suspend and resume for am3 and am4
debug check for a hard to debug case of bogus wakeup function flags.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=XPX3
-----END PGP SIGNATURE-----
Merge tag 'sched-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master
Pull scheduler fixes from Ingo Molnar:
"Fix a race introduced by the recent loadavg race fix, plus add a debug
check for a hard to debug case of bogus wakeup function flags"
* tag 'sched-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Warn if garbage is passed to default_wake_function()
sched: Fix race against ptrace_freeze_trace()
- Fix the layering violation in the use of the EFI runtime services
availability mask in users of the 'efivars' abstraction
- Revert build fix for GCC v4.8 which is no longer supported
- Clean up some x86 EFI stub details, some of which are borderline bugs
that copy around garbage into padding fields - let's fix these
out of caution.
- Fix build issues while working on RISC-V support
- Avoid --whole-archive when linking the stub on arm64
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=n3nF
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip into master
Pull EFI fixes from Ingo Molnar:
"Various EFI fixes:
- Fix the layering violation in the use of the EFI runtime services
availability mask in users of the 'efivars' abstraction
- Revert build fix for GCC v4.8 which is no longer supported
- Clean up some x86 EFI stub details, some of which are borderline
bugs that copy around garbage into padding fields - let's fix these
out of caution.
- Fix build issues while working on RISC-V support
- Avoid --whole-archive when linking the stub on arm64"
* tag 'efi-urgent-2020-07-25' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
efi: Revert "efi/x86: Fix build with gcc 4"
efi/efivars: Expose RT service availability via efivars abstraction
efi/libstub: Move the function prototypes to header file
efi/libstub: Fix gcc error around __umoddi3 for 32 bit builds
efi/libstub/arm64: link stub lib.a conditionally
efi/x86: Only copy upto the end of setup_header
efi/x86: Remove unused variables
-----BEGIN PGP SIGNATURE-----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=Cvv4
-----END PGP SIGNATURE-----
Merge tag '5.8-rc6-cifs-fix' of git://git.samba.org/sfrench/cifs-2.6 into master
Pull cifs fix from Steve French:
"A fix for a recently discovered regression in rename to older servers
caused by a recent patch"
* tag '5.8-rc6-cifs-fix' of git://git.samba.org/sfrench/cifs-2.6:
Revert "cifs: Fix the target file was deleted when rename failed."
Pull networking fixes from David Miller:
1) Fix RCU locaking in iwlwifi, from Johannes Berg.
2) mt76 can access uninitialized NAPI struct, from Felix Fietkau.
3) Fix race in updating pause settings in bnxt_en, from Vasundhara
Volam.
4) Propagate error return properly during unbind failures in ax88172a,
from George Kennedy.
5) Fix memleak in adf7242_probe, from Liu Jian.
6) smc_drv_probe() can leak, from Wang Hai.
7) Don't muck with the carrier state if register_netdevice() fails in
the bonding driver, from Taehee Yoo.
8) Fix memleak in dpaa_eth_probe, from Liu Jian.
9) Need to check skb_put_padto() return value in hsr_fill_tag(), from
Murali Karicheri.
10) Don't lose ionic RSS hash settings across FW update, from Shannon
Nelson.
11) Fix clobbered SKB control block in act_ct, from Wen Xu.
12) Missing newlink in "tx_timeout" sysfs output, from Xiongfeng Wang.
13) IS_UDPLITE cleanup a long time ago, incorrectly handled
transformations involving UDPLITE_RECV_CC. From Miaohe Lin.
14) Unbalanced locking in netdevsim, from Taehee Yoo.
15) Suppress false-positive error messages in qed driver, from Alexander
Lobakin.
16) Out of bounds read in ax25_connect and ax25_sendmsg, from Peilin Ye.
17) Missing SKB release in cxgb4's uld_send(), from Navid Emamdoost.
18) Uninitialized value in geneve_changelink(), from Cong Wang.
19) Fix deadlock in xen-netfront, from Andera Righi.
19) flush_backlog() frees skbs with IRQs disabled, so should use
dev_kfree_skb_irq() instead of kfree_skb(). From Subash Abhinov
Kasiviswanathan.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (111 commits)
drivers/net/wan: lapb: Corrected the usage of skb_cow
dev: Defer free of skbs in flush_backlog
qrtr: orphan socket in qrtr_release()
xen-netfront: fix potential deadlock in xennet_remove()
flow_offload: Move rhashtable inclusion to the source file
geneve: fix an uninitialized value in geneve_changelink()
bonding: check return value of register_netdevice() in bond_newlink()
tcp: allow at most one TLP probe per flight
AX.25: Prevent integer overflows in connect and sendmsg
cxgb4: add missing release on skb in uld_send()
net: atlantic: fix PTP on AQC10X
AX.25: Prevent out-of-bounds read in ax25_sendmsg()
sctp: shrink stream outq when fails to do addstream reconf
sctp: shrink stream outq only when new outcnt < old outcnt
AX.25: Fix out-of-bounds read in ax25_connect()
enetc: Remove the mdio bus on PF probe bailout
net: ethernet: ti: add NETIF_F_HW_TC hw feature flag for taprio offload
net: ethernet: ave: Fix error returns in ave_init
drivers/net/wan/x25_asy: Fix to make it work
ipvs: fix the connection sync failed in some cases
...
Currently, maximum physical memory allowed is equal to -PAGE_OFFSET.
That's why we remove any memory blocks spanning beyond that size. However,
it is done only for memblock containing linux kernel which will not work
if there are multiple memblocks.
Process all memory blocks to figure out how much memory needs to be removed
and remove at the end instead of updating the memblock list in place.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
