Remove the structure since a default one is now available.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The commit 318c3e15cd
added some "fck" clock alias to timer devices that are
not needed anymore since hwmod framework will create
them automatically.
A warning was added to highlight and thus fix the redundancy.
[ 0.616424] omap_timer.1: alias fck already exists
[ 0.621948] omap_timer.2: alias fck already exists
[ 0.627380] omap_timer.3: alias fck already exists
[ 0.632781] omap_timer.4: alias fck already exists
[ 0.638214] omap_timer.5: alias fck already exists
[ 0.643615] omap_timer.6: alias fck already exists
[ 0.649078] omap_timer.7: alias fck already exists
[ 0.654479] omap_timer.8: alias fck already exists
[ 0.659881] omap_timer.9: alias fck already exists
[ 0.665283] omap_timer.10: alias fck already exists
[ 0.670776] omap_timer.11: alias fck already exists
Remove all the clkdev entries for timer fck alias.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the init of card detect pin because
omap_mux_init_gpio() is called during hsmmc initialization
for the write protect and card detect pin.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Not in use anymore.
Signed-off-by: Bjarne Steinsbo <bsteinsbo@gmail.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
linux-omap is back at git.kernel.org. Path is the same than before except
-2.6 appendix.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'next' of git://git.infradead.org/users/vkoul/slave-dma: (63 commits)
dmaengine: mid_dma: mask_peripheral_interrupt only when dmac is idle
dmaengine/ep93xx_dma: add module.h include
pch_dma: Reduce wasting memory
pch_dma: Fix suspend issue
dma/timberdale: free_irq() on an error path
dma: shdma: transfer based runtime PM
dmaengine: shdma: protect against the IRQ handler
dmaengine i.MX DMA/SDMA: add missing include of linux/module.h
dmaengine: delete redundant chan_id and chancnt initialization in dma drivers
dmaengine/amba-pl08x: Check txd->llis_va before freeing dma_pool
dmaengine/amba-pl08x: Add support for sg len greater than one for slave transfers
serial: sh-sci: don't filter on DMA device, use only channel ID
ARM: SAMSUNG: Remove Samsung specific enum type for dma direction
ASoC: Samsung: Update DMA interface
spi/s3c64xx: Merge dma control code
spi/s3c64xx: Add support DMA engine API
ARM: SAMSUNG: Remove S3C-PL330-DMA driver
ARM: S5P64X0: Use generic DMA PL330 driver
ARM: S5PC100: Use generic DMA PL330 driver
ARM: S5PV210: Use generic DMA PL330 driver
...
Fix up fairly trivial conflicts in
- arch/arm/mach-exynos4/{Kconfig,clock.c}
- arch/arm/mach-s5p64x0/dma.c
get_context_loss_count functions return context loss count as u32, and
zero means an error. However, zero is also returned when context has
never been lost and could also be returned when the context loss count
has wrapped and goes to zero.
Change the functions to return an int, with negative value meaning an
error.
OMAP HSMMC code uses omap_pm_get_dev_context_loss_count(), but as the
hsmmc code handles the returned value as an int, with negative value
meaning an error, this patch actually fixes hsmmc code also.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated to fix a warning with recent dmtimer changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the typo, instead it should be SDMMC1
USBC1 is not related to MMC1 I/Os
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
MMC1 data line IO's are powered down in before set regulator function.
IO's should not be powered ON when regulator is OFF.
Keep the IO's in power pown mode after regulator OFF otherwise VMODE_ERROR
interrupt is generated due to mismatch in input (regulator)
voltage and MMC IO drive voltage.
Delete incorrect comments which are not applicable for OMAP4.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Reported-by: Viswanath Puttagunta <vishp@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit d6504acd21 ("OMAP2+: hwmod:
remove OMAP_CHIP*") tests the inverse condition of what it should be
testing for the return value from omap_hwmod_register(). This causes
several IP blocks to not be registered on several OMAP3 family devices.
Fixing that bug also unmasked another bug, originally reported by
Chase Maupin <chase.maupin@ti.com> and then subsequently by Abhilash K
V <abhilash.kv@ti.com>, which caused SmartReflex IP blocks to be
registered on SoCs that don't support them.
Thanks to Russell King - ARM Linux <linux@arm.linux.org.uk> for comments
on a previous version of the patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Chase Maupin <chase.maupin@ti.com>
Cc: Abhilash K V <abhilash.kv@ti.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 4d17aeb1c5 ("OMAP: I2C: split
device registration and convert OMAP2+ to omap_device") makes
omap2_i2c_add_bus() return a pointer to an omap_device instead on
success instead of 0.
This breaks the omap_register_i2c_bus() ABI and results in the igep0020
board code detecting an I2C bus registration error when there is none.
Fix the problem by using PTR_RET() instead of PTR_ERR() in
omap2_i2c_add_bus().
Reported-by: Alexander Kinzer <a.kinzer@plusoptix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[tony@atomide.com: updated to return pdev instead of od]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include linux/module.h to fix below build error:
CC arch/arm/plat-omap/dmtimer.o
arch/arm/plat-omap/dmtimer.c:184: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:184: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:184: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:215: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:215: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:215: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:228: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:228: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:228: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:234: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:234: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:234: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:240: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:240: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:240: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:248: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:248: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:248: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:294: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:294: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:294: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:302: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:302: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:302: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:316: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:316: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:316: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:344: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:344: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:344: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:361: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:361: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:361: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:380: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:380: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:380: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:406: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:406: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:406: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:443: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:443: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:443: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:468: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:468: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:468: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:494: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:494: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:494: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:517: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:517: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:517: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:534: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:534: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:534: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:549: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:549: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:549: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:561: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:561: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:561: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:572: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:572: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:572: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:587: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:587: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:587: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:604: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:604: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/arm/plat-omap/dmtimer.c:604: warning: parameter names (without types) in function declaration
arch/arm/plat-omap/dmtimer.c:746: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-omap/dmtimer.c:746: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:746: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
arch/arm/plat-omap/dmtimer.c:746: warning: function declaration isn't a prototype
arch/arm/plat-omap/dmtimer.c:747: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-omap/dmtimer.c:747: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:747: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
arch/arm/plat-omap/dmtimer.c:747: warning: function declaration isn't a prototype
arch/arm/plat-omap/dmtimer.c:748: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-omap/dmtimer.c:748: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:748: warning: type defaults to 'int' in declaration of 'MODULE_ALIAS'
arch/arm/plat-omap/dmtimer.c:748: warning: function declaration isn't a prototype
arch/arm/plat-omap/dmtimer.c:749: error: expected declaration specifiers or '...' before string constant
arch/arm/plat-omap/dmtimer.c:749: warning: data definition has no type or storage class
arch/arm/plat-omap/dmtimer.c:749: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
arch/arm/plat-omap/dmtimer.c:749: warning: function declaration isn't a prototype
make[1]: *** [arch/arm/plat-omap/dmtimer.o] Error 1
make: *** [arch/arm/plat-omap] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Include linux/module.h to fix below build error:
CC arch/arm/mach-omap2/omap_l3_noc.o
arch/arm/mach-omap2/omap_l3_noc.c:240: error: expected ',' or ';' before 'MODULE_DEVICE_TABLE'
arch/arm/mach-omap2/omap_l3_noc.c:250: error: 'THIS_MODULE' undeclared here (not in a function)
make[1]: *** [arch/arm/mach-omap2/omap_l3_noc.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit f718e2c034 (ARM: OMAP2+: devices:
Remove all omap_device_pm_latency structures) removed these structures.
Commit 3528c58eb9 (OMAP: omap_device:
when building return platform_device instead of omap_device) now
returns platform_device instead of omap_device.
Fix up the omap-mcpdm init function since this part comes via sound
tree, and there has been changes regarding to hwmod/omap_device_build.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
CC: Benoit Cousson <b-cousson@ti.com>
CC: Kevin Hilman <khilman@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
When customizing omap2plus_defconfig to build for only
one board (omap3evm), I came across these warnings and
errors (filenames truncated):
arch/arm/mach-omap2/board-generic.c:76:20: warning: 'omap4_init' defined but not used
arch/arm/mach-omap2/built-in.o: In function `omap2420_init_early':
arch/arm/mach-omap2/io.c:364: undefined reference to `omap2_set_globals_242x'
arch/arm/mach-omap2/io.c:366: undefined reference to `omap2xxx_voltagedomains_init'
arch/arm/mach-omap2/io.c:367: undefined reference to `omap242x_powerdomains_init'
arch/arm/mach-omap2/io.c:368: undefined reference to `omap242x_clockdomains_init'
arch/arm/mach-omap2/io.c:369: undefined reference to `omap2420_hwmod_init'
arch/arm/mach-omap2/built-in.o: In function `omap2430_init_early':
arch/arm/mach-omap2/io.c:376: undefined reference to `omap2_set_globals_243x'
arch/arm/mach-omap2/io.c:378: undefined reference to `omap2xxx_voltagedomains_init'
arch/arm/mach-omap2/io.c:379: undefined reference to `omap243x_powerdomains_init'
arch/arm/mach-omap2/io.c:380: undefined reference to `omap243x_clockdomains_init'
arch/arm/mach-omap2/io.c:381: undefined reference to `omap2430_hwmod_init'
arch/arm/mach-omap2/built-in.o: In function `omap4430_init_early':
arch/arm/mach-omap2/io.c:436: undefined reference to `omap2_set_globals_443x'
arch/arm/mach-omap2/io.c:438: undefined reference to `omap44xx_voltagedomains_init'
arch/arm/mach-omap2/io.c:439: undefined reference to `omap44xx_powerdomains_init'
arch/arm/mach-omap2/io.c:440: undefined reference to `omap44xx_clockdomains_init'
arch/arm/mach-omap2/io.c:441: undefined reference to `omap44xx_hwmod_init'
This patch fixes them.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Acked-by: Thomas Weber <weber@corscience.de>
[tony@atomide.com: updated to fix warnings for board-generic.c]
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-3.2/drivers' of git://git.kernel.dk/linux-block: (30 commits)
virtio-blk: use ida to allocate disk index
hpsa: add small delay when using PCI Power Management to reset for kump
cciss: add small delay when using PCI Power Management to reset for kump
xen/blkback: Fix two races in the handling of barrier requests.
xen/blkback: Check for proper operation.
xen/blkback: Fix the inhibition to map pages when discarding sector ranges.
xen/blkback: Report VBD_WSECT (wr_sect) properly.
xen/blkback: Support 'feature-barrier' aka old-style BARRIER requests.
xen-blkfront: plug device number leak in xlblk_init() error path
xen-blkfront: If no barrier or flush is supported, use invalid operation.
xen-blkback: use kzalloc() in favor of kmalloc()+memset()
xen-blkback: fixed indentation and comments
xen-blkfront: fix a deadlock while handling discard response
xen-blkfront: Handle discard requests.
xen-blkback: Implement discard requests ('feature-discard')
xen-blkfront: add BLKIF_OP_DISCARD and discard request struct
drivers/block/loop.c: remove unnecessary bdev argument from loop_clr_fd()
drivers/block/loop.c: emit uevent on auto release
drivers/block/cpqarray.c: use pci_dev->revision
loop: always allow userspace partitions and optionally support automatic scanning
...
Fic up trivial header file includsion conflict in drivers/block/loop.c
* 'for-3.2/core' of git://git.kernel.dk/linux-block: (29 commits)
block: don't call blk_drain_queue() if elevator is not up
blk-throttle: use queue_is_locked() instead of lockdep_is_held()
blk-throttle: Take blkcg->lock while traversing blkcg->policy_list
blk-throttle: Free up policy node associated with deleted rule
block: warn if tag is greater than real_max_depth.
block: make gendisk hold a reference to its queue
blk-flush: move the queue kick into
blk-flush: fix invalid BUG_ON in blk_insert_flush
block: Remove the control of complete cpu from bio.
block: fix a typo in the blk-cgroup.h file
block: initialize the bounce pool if high memory may be added later
block: fix request_queue lifetime handling by making blk_queue_cleanup() properly shutdown
block: drop @tsk from attempt_plug_merge() and explain sync rules
block: make get_request[_wait]() fail if queue is dead
block: reorganize throtl_get_tg() and blk_throtl_bio()
block: reorganize queue draining
block: drop unnecessary blk_get/put_queue() in scsi_cmd_ioctl() and blk_get_tg()
block: pass around REQ_* flags instead of broken down booleans during request alloc/free
block: move blk_throtl prototypes to block/blk.h
block: fix genhd refcounting in blkio_policy_parse_and_set()
...
Fix up trivial conflicts due to "mddev_t" -> "struct mddev" conversion
and making the request functions be of type "void" instead of "int" in
- drivers/md/{faulty.c,linear.c,md.c,md.h,multipath.c,raid0.c,raid1.c,raid10.c,raid5.c}
- drivers/staging/zram/zram_drv.c
slave->duplex is a u8 type so the in bond_info_show_slave() when we
check "if (slave->duplex == -1)", it's always false.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to support other Optima types, introduced an accidental
regression that caused 88E8059 to come up in 10Mbit/sec.
The Yukon Optima supports a reverse auto-negotiation feature that
was incorrectly setup, and not needed. The feature could be used to
allow wake-on-lan at higher speeds. But doing it correctly would require
other changes to initialization.
Reported-by: Pavel Mateja <pavel@netsafe.cz>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation for how the length of attributes
is checked is wrong ("Exact length" isn't true, the
policy checks are for "minimum length") and a bit
misleading. Make it more complete and explain what
really happens.
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
L2TP for example uses NLA_MSECS like this:
policy:
[L2TP_ATTR_RECV_TIMEOUT] = { .type = NLA_MSECS, },
code:
if (info->attrs[L2TP_ATTR_RECV_TIMEOUT])
cfg.reorder_timeout = nla_get_msecs(info->attrs[L2TP_ATTR_RECV_TIMEOUT]);
As nla_get_msecs() is essentially nla_get_u64() plus the
conversion to a HZ-based value, this will not properly
reject attributes from userspace that aren't long enough
and might overrun the message.
Add NLA_MSECS to the attribute minlen array to check the
size properly.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i825xx and xscale are "sub" Kconfigs to NET_VENDOR_INTEL, so
NET_VENDOR_INTEL should contain ALL the dependencies of the
"sub" Kconfigs.
Same with 8390 is a "sub" Kconfig to NET_VENDOR_NATSEMI, so
NET_VENDOR_NATSEMI needs to contains ALL the dependencies.
Freescale Kconfig only had fs_enet as a sub Kconfig, and already
contained the needed dependencies, just cleaned up the dependencies.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing VRRP v2 using macvlan several problems were
discovered. VRRP is weird in that all routers participating
in a redundant group use the same virtual MAC address.
Macvlan is a natural driver to use for this but it doesn't
work. The problem is that packets with a macvlan device's
source address are not received.
The problem is actually a regression that date back almost 2 years now.
The original problems started with:
commit 618e1b7482
Author: Arnd Bergmann <arnd@arndb.de>
Date: Thu Nov 26 06:07:10 2009 +0000
macvlan: implement bridge, VEPA and private mode
This patches restores the original 2.6.32 behavior. Allowing multicast
packets received with the VRRP source address to be received.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.121.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During shutdown, it is impossible to reliably disable the timer and
reset_task threads. Each thread can schedule the other, which leads to
shutdown code that chases its tail.
To fix the problem, this patch removes the ability of tg3_reset_task to
schedule a new timer thread. To support this change, tg3_timer no
longer terminates itself, but rather goes into a polling mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for multiple threads in the tg3 driver to each attempt to
schedule a run of tg3_reset_task(). The multiple tg3_reset_task
executions could all wind up on the same queue (and execute serially) or
wind up on the queues of another processor (which could execute in
parallel). Either scenario is not what was truly desired.
This patch adds a new flag, TG3_FLAG_RESET_TASK_PENDING, and uses it to
determine whether or not to schedule another run of tg3_reset_task().
With the new flag comes two new functions to facilitate scheduling and
descheduling of tg3_reset_task().
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to attempt to obtain the PCI function number from
the device rather than accept the number handed by the kernel. In
pass-through scenarios, the function number handed by the kernel may not
reflect the true function of the device.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug where the irq error cleanup path did not free all
the resources it allocated.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Ben Li <benli@broadcom.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the error recovery resource unwind path, it is possible for the
driver to attempt to unmap a fragment that hadn't been mapped. This
patch fixes the problem by correcting the "last" parameter supplied.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new 4k tx bd segmentation code had a bug in the error cleanup path.
If the driver did not map all the physical fragments, the abort path
would wind up advancing the producer index beyond the point where the
setup code stopped. This would ultimately turn into a tx recovery error
where the driver would expect the skb pointer to be set when it isn't.
This patch fixes the problem, and then makes the code a little easier to
understand.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
APE mutex register blocks are shared by all ports of multiport devices.
For some mutexing purposes, each function is assigned their own
register. For other cases, each function is assigned its own request
and grant bits of a single register. For the latter cases, the tg3
driver is incorrectly allowing each function to use the same set of
grant / request bits. This patch fixes the code so that each function
uses the appropriate bitset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 27920651fe "PM / Freezer: Make fake_signal_wake_up() wake
TASK_KILLABLE tasks too" updated fake_signal_wake_up() used by freezer
to wake up KILLABLE tasks. Sending unsolicited wakeups to tasks in
killable sleep is dangerous as there are code paths which depend on
tasks not waking up spuriously from KILLABLE sleep.
For example. sys_read() or page can sleep in TASK_KILLABLE assuming
that wait/down/whatever _killable can only fail if we can not return
to the usermode. TASK_TRACED is another obvious example.
The previous patch updated wait_event_freezekillable() such that it
doesn't depend on the spurious wakeup. This patch reverts the
offending commit.
Note that the spurious KILLABLE wakeup had other implicit effects in
KILLABLE sleeps in nfs and cifs and those will need further updates to
regain freezekillable behavior.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit 27920651fe "PM / Freezer: Make fake_signal_wake_up() wake
TASK_KILLABLE tasks too" updated fake_signal_wake_up() used by freezer
to wake up KILLABLE tasks. Sending unsolicited wakeups to tasks in
killable sleep is dangerous as there are code paths which depend on
tasks not waking up spuriously from KILLABLE sleep.
For example. sys_read() or page can sleep in TASK_KILLABLE assuming
that wait/down/whatever _killable can only fail if we can not return
to the usermode. TASK_TRACED is another obvious example.
The offending commit was to resolve freezer hang during system PM
operations caused by KILLABLE sleeps in network filesystems.
wait_event_freezekillable(), which depends on the spurious KILLABLE
wakeup, was added by f06ac72e92 "cifs, freezer: add
wait_event_freezekillable and have cifs use it" to be used to
implement killable & freezable sleeps in network filesystems.
To prepare for reverting of 27920651fe, this patch reimplements
wait_event_freezekillable() using freezer_do_not_count/freezer_count()
so that it doesn't depend on the spurious KILLABLE wakeup. This isn't
very nice but should do for now.
[tj: Refreshed patch to apply to linus/master and updated commit
description on Rafael's request.]
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit
f71648d73c (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. A companion
patch changes the PM core's behavior, but we also need to change the
USB core. In particular, this patch (as1493) updates the device's
last_busy time when an autosuspend fails, so that the PM core will
retry the autosuspend in the future when the delay time expires
again.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Originally, the runtime PM core would send an idle notification
whenever a suspend attempt failed. The idle callback routine could
then schedule a delayed suspend for some time later.
However this behavior was changed by commit
f71648d73c (PM / Runtime: Remove idle
notification after failing suspend). No notifications were sent, and
there was no clear mechanism to retry failed suspends.
This caused problems for the usbhid driver, because it fails
autosuspend attempts as long as a key is being held down. Therefore
this patch (as1492) adds a mechanism for retrying failed
autosuspends. If the callback routine updates the last_busy field so
that the next autosuspend expiration time is in the future, the
autosuspend will automatically be rescheduled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@kernel.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Remove an "if" check, that repeats an equivalent one 6 lines above.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Commit 03ca370fbf (PM / OPP: Add
OPP availability change notifier) does not compile if CONFIG_PM_OPP
is not set:
arch/arm/plat-omap/omap-pm-noop.o: In function `opp_get_notifier':
include/linux/opp.h:103: multiple definition of `opp_get_notifier'
include/linux/opp.h:103: first defined here
Also fix incorrect comment.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
With delta type being int, its value is made zero
for all values of now > 0x80000000.
Hence fixing it.
Signed-off-by: venu byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch:
* Substitutes some obsolete references to kernel/power/process.c by
kernel/freezer.c.
* Mentions kernel/freezer.c as being part of the "freezer" code along
with the rest of the files.
* Fixes a trivial typo.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Remove the suspend_cpu_hotplug declaration, which doesn't correspond
to an existing variable.
[rjw: Added the changelog.]
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The CPU hotplug notifications sent out by the _cpu_up() and _cpu_down()
functions depend on the value of the 'tasks_frozen' argument passed to them
(which indicates whether tasks have been frozen or not).
(Examples for such CPU hotplug notifications: CPU_ONLINE, CPU_ONLINE_FROZEN,
CPU_DEAD, CPU_DEAD_FROZEN).
Thus, it is essential that while the callbacks for those notifications are
running, the state of the system with respect to the tasks being frozen or
not remains unchanged, *throughout that duration*. Hence there is a need for
synchronizing the CPU hotplug code with the freezer subsystem.
Since the freezer is involved only in the Suspend/Hibernate call paths, this
patch hooks the CPU hotplug code to the suspend/hibernate notifiers
PM_[SUSPEND|HIBERNATE]_PREPARE and PM_POST_[SUSPEND|HIBERNATE] to prevent
the race between CPU hotplug and freezer, thus ensuring that CPU hotplug
notifications will always be run with the state of the system really being
what the notifications indicate, _throughout_ their execution time.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'for-linus' of git://github.com/cmetcalf-tilera/linux-tile:
arch/tile: factor out <arch/opcode.h> header
arch/tile: add the <arch> headers to the set of installed kernel headers
arch/tile: avoid exporting a symbol no longer used by gcc
arch/tile: avoid ISO namespace pollution with <asm/sigcontext.h>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix panic in RC error flushing logic
IB/iser: DMA unmap TX bufs used for iSCSI/iSER headers
IB/iser: Use separate buffers for the login request/response
IB/mthca: Fix buddy->num_free allocation size
