Input device must be released(input_free_device) when ads7846_probe_dt
fails. This fixes the same by releasing resources on failure.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By writing zero to both the active and idle cycle times the maXTouch device
is put into a deep sleep mode when it consumes minimal power. It is
unnecessary to change the configuration of any other objects (for example
to disable T9 touchscreen).
It is counterproductive to reset the chip on resume, it will result in a
long delay. However it is necessary to issue a calibrate command after the
chip has spent any time in deep sleep.
This patch also deals with the situation where the power configuration is
zero on probe, which would mean that the device never wakes up to execute
commands.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Provide device tree support and binding information. Also provide support
for a new chip "pixcir_tangoc".
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some variants of the Pixcir touch controller support up to 5 simultaneous
fingers and hardware tracking IDs. Prepare the driver for that.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch to using the Type-B Multi-Touch protocol.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Such as found on the new Toshiba Portégé Z30-A and Z40-A.
Signed-off-by: Yunkang Tang <yunkang.tang@cn.alps.com>
[hdegoede@redhat.com: Remove softbutton handling, this is done in userspace]
[hdegoede@redhat.com: Report INPUT_PROP_BUTTONPAD]
[hdegoede@redhat.com: Do not report fake PRESSURE, reporting BTN_TOUCH is
enough]
[hdegoede@redhat.com: Various cleanups / refactoring]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
So that decode functions can return a failure when appropriate.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If we detect more then 2 fingers report 2 touches, rather then only
reporting the upper left corner of the bounding box.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Move all the semi-mt specific handling shared between the v3 and v4
handling code to a common helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
For v3 protocol devices, use the more accurate single touch data when the
mt data contains only one finger. Note the mt data reporting a finger count
of 1 should never happen, but better safe then sorry.
This brings the v3 bitmap handling in line with what the v4 code does,
allowing to factor out the common bits into a helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When there are 2 fingers on the pad we don't know which one is which, so
use input_mt_assign_slots to make sure the right set of coordinates ends
up in the right slot.
Besides ensuring things end up in the right slot, this also results in a
nice cleanup, since sync_frame also handles non mt position and btn_touch
reporting.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a preparation patch for switching the DIY mt handling to using
input_mt_assign_slots && input_mt_sync_frame.
struct alps_fields is quite large, so while making changes to almost all uses
of it lets put it in our priv data instead of on the stack.
Having it in our priv data also allows using it directly for storing values
which need to be cached, rather then having separate x, y, z, fingers, etc.
copies in our priv data.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes 2 fingers at the same height or width on the touchpad getting
reported at different y / x coordinates.
Note num_bits is always at least 1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
alps_process_bitmap was resetting the point bit-count as soon as it saw
2 0 bits in a row. This means that unless the high point actually is at
the end of the bitmap, it would always get its num_bits set to 0.
Instead reset num_bits to 0 on a 0->1 transition, so that with > 2 fingers
we only count the number of bits occupied by the highest finger.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Factor out the identical code for getting the bitmap points for x and y into
a helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rushmore models don't have the Y-axis data in the bitmap inverted. Since
we now have 2 different Y orientations, make the Y bitmap data processing
use a forward loop like the X bitmap data processing, unifying the 2,
and invert the data later, except on Rushmore.
So far no-one has noticed this because the synaptics driver only uses the
non mt coordinates (except on clickpads, and there are no alps clickpads
using process_bitmap).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
V3 models only report mt bitmap data when there are 2 or more fingers on
the touchpad. So always generate 2 positions in alps_process_bitmap, and
for v3 models only fall back to st data when there was no mt data in a
mt packet (which should never happen).
This fixes 2 finger scrolling not working when using 2 fingers close to
each other.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wacom.ko is now a full HID driver, we have to move it into the proper
subdirectory: drivers/hid.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
No Functional changes, just some reordering.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
pktlen is now overwritten by the driver directly by reading the hid
report descriptor. There is no need to declare it statically.
We also move down the position of the field in the struct so that
we can keep the current declaration of Wacom devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This may infer a small difference with the previous implementation
due to the DIV_ROUND_CLOSEST() in the hid implementation.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
HID already parses the report descriptor, so use it instead of implementing
our own. The special case for Bamboo PT 3rd gen is also removed and
handled in the same way Intuos 5 is treated, by hardcoding it in the
driver. Last, the unit_exponent stored into the hid field already is
signed, so there is no need to handle a two's complement anymore.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Removes one more need of usb and intf.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the HID device as the parent for the power device when dealing with
a wireless receiver.
Removes one more usb dependency and does not break user space.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wacom tablets can share different physical sensors on one physical device.
These are called siblings in the code. The current way of implementation
relies on the USB topology to be able to share data amongs those sensors.
We can replace the code to match a HID subsystem, without involving the USB
topology:
- the first probed sensor does not find any siblings in the list
wacom_udev_list, so it creates its own wacom_hdev_data with its own
struct hid_device
- the other sensor checks the current list of siblings in wacom_hdev_data,
and if there is a match, it associates itself to the matched device.
To be sure that we are not associating different sensors from different
physical devices, we also check for the phys path of the hid device which
contains the USB topology.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Matches the current behavior of the HID subsystem and removes one more
dependency over USB.
The current user space clients which relies on this to fetch the
LEDs path need an update. However, we already break them in the
kernel v3.11 for the Bluetooth Wacom devices. They are going to be fixed
soon.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Removes one more dependency over USB, but requires some changes in
the user space to find the sysfs files correctly.
This patch breaks the user space. However, the number of program
accessing the LEDs is quite limited and we can easily patch them
to handle the new HID behavior.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This removes an USB dependency and is more accurate: the computed pktlen
is the actual maximum size of the reports forwarded by the device.
Given that the pktlen is correctly computed/validated, we can store it now
in the features struct instead of having a special handling in the rest of
the code.
Likewise, this information is not mandatory anymore in the description
of devices in wacom_wac.c. They will be removed in a separate patch.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
HID core already retrieves the report descritor. There is no need
to ask ourself for one.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wacom.ko was a plain USB driver for a HID device. The communications
from/to the devices can actually be replaced with the HID API.
At the USB level, the reports are exactly the same.
This will allow to use uhid virtual devices instead of true USB devices.
This step is necessary to implement regression tests.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All USB Wacom tablets are actually HID devices.
For historical reasons, they are handled as plain USB devices.
The current code makes more and more reference to the HID subsystem
like implementing its own HID report descriptor parser to handle new
devices.
From the user point of view, we can transparently switch from this state
to a driver handled in the HID subsystem and clean up a lot of USB specific
code in the wacom.ko driver.
The other benefit once the USB dependecies have been removed is that we can
use a tool like uhid to make regression tests and allow further cleanup or
new implementations without risking breaking current behaviors.
To match the current handling of devices in wacom_wac.c, we rely on the
hid_type set by usbhid. usbhid sets the hid_type to HID_TYPE_USBMOUSE when
it sees a USB boot mouse protocol declared and HID_TYPE_USBNONE when the
device is plain HID. There is thus a one to one matching between the list
of supported devices before and after the switch from USB to HID.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current wacom code redefines constants that are already in linux/hid.h
This patch includes the official implementation and use it accross the code.
There is a conflict with HID_USAGE and others at the same level:
- in the wacom.ko implementation, those are the #define regarding the
value of the field in the report descriptor
- in the hid.h, those are bitmask
So add HDESC_ in their current definition.
Also, the struct hid_descriptor slightly differs from the linux/hid.h
point of view, so mark it as custom for this driver.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Wireless Receiver should also behave in the same way than regular
USB devices.
To simplify the unregistering of the different devices,
wacom_unregister_inputs() is introduced.
For consistency, the function wacom_register_input() is renamed into
wacom_register_inputs().
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MSC_SERIAL can be safely removed from pad devices. If it is not
here, xf86-input-wacom correctly generates ones for its internal
use.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MSC_SERIAL can be safely removed from the pad device.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We rely on the return code of wacom_bpt*() to do the input_sync().
wacom_wac_irq() then properly sync the input devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MSC_SERIAL can be safely dropped for pad input devices.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently, the pad events are sent through the stylus input device
for the Intuos/Cintiqs, and through the touch input device for the
Bamboos.
To differentiate the buttons pressed on the pad from the ones pressed
on the stylus, the Intuos/Cintiq uses MISC_SERIAL and ABS_MISC. This
lead to a multiplexing of the events into one device, which are then
splitted out in xf86-input-wacom. Bamboos are not using MISC events
because the pad is attached to the touch interface, and only BTN_TOUCH
is used for the finger (and DOUBLE_TAP, etc...). However, the user space
driver still splits out the pad from the touch interface in the same
way it does for the pro line devices.
The other problem we can see with this fact is that some of the Intuos
and Cintiq have a wheel, and the effective range of the reported values
is [0..71]. Unfortunately, the airbrush stylus also sends wheel events
(there is a small wheel on it), but in the range [0..1023]. From the user
space point of view it is kind of difficult to understand that because
the wheel on the pad are quite common, while the airbrush tool is not.
A solution to fix all of these problems is to split out the pad device
from the stylus/touch. This decision makes more sense because the pad is
not linked to the absolute position of the finger or pen, and usually, the
events from the pad are filtered out by the compositor, which then convert
them into actions or keyboard shortcuts.
For backward compatibility with current xf86-input-wacom, the pad devices
still present the ABS_X, ABS_Y and ABS_MISC events, but they can be
completely ignored in the new implementation.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This field was not used for 9 years, it is time to assign it.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This reverts commit 1b2faaf7e2.
The Intuos4 series presents a bug in which it hangs if it receives
a set feature command while switching to the enhanced mode.
This bug is triggered when plugging an Intuos 4 while having
a gnome user session up and running.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
wacom_wac.h will be moving to drivers/hid. Since we only need 3 definitions
from it let's simply copy them over.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wire up open/close so we do not try to send events until someone uses them;
this also allows us to remove micro_ts_remove() and rely fully on managed
resources.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds a driver for the touchscreen connected to the Atmel
microcontroller on the iPAQ h3xxx series.
Based on a driver from handhelds.org 2.6.21 kernel, written by Alessandro
GARDICH, with the bulk of the code for the new input architecture rewritten
by Dmitry Atamonow, and the final polish by Linus Walleij.
Signed-off-by: Alessandro GARDICH <gremlin@gremlin.it>
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTzJFGAAoJEHm+PkMAQRiGNzQH/087gQch5K+A2HKvPzjUXq57
G82DJHLONMMq8+NY3Vqhp8g2V8zRbXGJEvMJMsyuscO37Vo7ADcrYo8lqY9w5bIl
h+Zarhkqz0rqRs2SfMMIVzdd2W7MzL+lqj3GplGPxHztw0+qk7PRKILx6eRppGaH
JaD4NfkD5+1vfve/2d1ze9D5pCiw6PFNzjesKZxScQhNhIyLdRamfSTY4r9XeURo
CxpwjphEYfvAcgc39mwzEHPHyKSqULu0By6R8FXQpJ9QjVtzcGEiF+cPqGncpZOR
5ZSyU5e1CpBl9w8o6Lm9ewXmaCSnBU/VFrOwWvZrXfokZedXBOz7KdShU93XFjU=
=0VJM
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc6' into next
Merge with mainline to bring in changes to MFD to allow merging
ipaq-micro-ts driver.
maXTouch chips allow the reading of multiple messages in a single I2C
transaction, which reduces bus overhead and improves performance/latency. The
number of messages available to be read is given by the value in the T44
object which is located directly before the T5 object.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is in preparation for support of the T44 message count object.
Also, cache T5 address to avoid lookup on every interrupt cycle.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By storing the previous T6 status byte multiple debug output of the same
status can be suppressed (for example CFGERR).
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The T5 object may have various sizes depending on the objects used on the
particular maXTouch chip and firmware version, therefore it can't be
hardcoded in the driver. Allocate a buffer on probe instead.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MXT device may be in bootloader mode on probe, due to:
1) APP CRC failure, either:
a) flash corruption
b) bad power or other intermittent problem while checking CRC
2) If the device has been reset 10 or more times without accessing comms
3) Warm probe, device was in bootloader mode already
This code attempts to recover from 1(b) and 3.
There is an additional complexity: we have to try two possible bootloader
addresses because the mapping is not one-to-one and we don't know the exact
model yet.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Later chips (for example mXT1664S) different mappings for bootloader
addresses. This means that we must look at the family ID to determine
which address to use.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On a warm probe, the device might be in a state where an flash operation was
not completed.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the bootloader on the touchscreen controller fails to initialise the
firmware image, it stays in bootloader mode and reports a failure. It is
possible to reflash a working firmware image from this state.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
By validating the checksum, we can identify if the configuration is
corrupt. In addition, this patch writes the configuration in a short
series of block writes rather than as many individual values.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The existing implementation which encodes the configuration as a binary
blob in platform data is unsatisfactory since it requires a kernel
recompile for the configuration to be changed, and it doesn't deal well
with firmware changes that move values around on the chip.
Atmel define an ASCII format for the configuration which can be exported
from their tools. This patch implements a parser for that format which
loads the configuration via the firmware loader and sends it to the MXT
chip.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Touchpads are pointers, so make sure to pass the correct values to
input_mt_report_pointer_emulation(). Without this, tap-to-click doesn't
work.
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is useful to initialise the input device later:
- Screen parameters may not be not known yet, for instance if waiting for
firmware loader to return.
- Device may be in bootloader mode on probe (but could still be recovered by
firmware download).
In addition, later devices have a different touchscreen object (T100) which
requires handling differently.
This also reduces the complexity of the probe function.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The maXTouch chips use the CHG line to generate status events in bootloader
mode, and during configuration download, before there is enough information
to configure the input device. Therefore set up the interrupt handler
earlier.
However, this introduces states where parts of the interrupt processing
must not run. Use data->object_table as a way to tell whether the chip
information is valid, and data->input_dev as a way to tell whether it is
valid to generate input report.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert the monotonic timestamp with ktime_mono_to_real() in
evdev_events().
In evdev_queue_syn_dropped() we can call either ktime_get() or
ktime_get_real() depending on the clkid. No point in having two calls
for CLOCK_REALTIME.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The memory are mapped using of_ioremap() which is
an indication this is sbus memory.
Shift all uses of inb/outb to the sbus variants.
The inb/outb methods uses ASI_PHYS_BYPASS_EC_E_L,
whereas sbus_ variants uses ASI_PHYS_BYPASS_EC_E.
The difference is if the reads/writes are done in
native or little endian.
But for byte reads/writes there is no difference
so this does not matter for inb/outb - and this
driver only uses the byte variants.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ioctl is the counterpart to EVIOCGVERSION and returns the
uinput-version the kernel was compiled with.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This moves basic checks and setup from uinput_setup_device() into
uinput_validate_absbits() to make it easier to use. This way, we can call
it from other places without copying the boilerplate code.
Reviewed-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It's possible that the controller has an individually switchable power supply.
Therefore add support to control a supplying regulator.
As this is not always the case, the regulator is requested as optional.
Signed-off-by: Heiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use clk_prepare_enable/clk_disable_unprepare to make the driver
work properly with common clock framework.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Recent version of xf86-input-wacom no longer support directly accessing
serial tablets. Instead xf86-input-wacom now expects all wacom tablets to
be driven by the kernel and to show up as evdev devices.
This has caused old serial Wacom tablets to stop working for people who still
have such tablets. Julian Squires has written a serio input driver to fix this:
https://github.com/tokenrove/wacom-serial-iv
This is a cleaned up version of this driver with improved Graphire support
(I own an old Graphire myself).
Signed-off-by: Julian Squires <julian@cipht.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We attempt to remove noise from coordinates reported by devices in
input_handle_abs_event(), unfortunately, unless we were dropping the
event altogether, we were ignoring the adjusted value and were passing
on the original value instead.
Cc: stable@vger.kernel.org
Reviewed-by: Andrew de los Reyes <adlr@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch introduces the use of managed interfaces like devm_kzalloc,
devm_input_allocate_device, devm_request_threaded_irq etc. and does away
with the calls to free the allocated memory. The remove function is no
longer required and is completely done away with. Also, the labels in the
probe function are removed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds a driver for Microchips CAP1106, an I2C driven, 6-channel
capacitive touch sensor.
For now, only the capacitive buttons are supported, and no specific
settings that can be tweaked for individual channels, except for the
device-wide sensitivity gain. The defaults seem to work just fine out of
the box, so I'll leave configurable parameters for someone who's in need
of them and who can actually measure the impact. All registers are
prepared, however. Many of them are just not used for now.
The implementation does not make any attempt to be compatible to platform
data driven boards, but fully depends on CONFIG_OF.
Power management functions are also left for volounteers with the ability
to actually test them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix checkpatch warning:
"WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required"
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Per license_is_gpl_compatible(), the MODULE_LICENSE() string for GPL v2 is
"GPL v2", not "GPLv2". Use "GPL v2" so this module doesn't taint the
kernel.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add #ifdef CONFIG_PM_SLEEP around keyscan_supend() and keyscan_resume() to
fix the following compiler warnings occuring if CONFIG_PM_SLEEP is unset:
+ /scratch/kisskb/src/drivers/input/keyboard/st-keyscan.c: warning: 'keyscan_resume' defined but not used [-Wunused-function]: => 235:12
+ /scratch/kisskb/src/drivers/input/keyboard/st-keyscan.c: warning: 'keyscan_suspend' defined but not used [-Wunused-function]: => 218:12
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lkml.org/lkml/2014/7/8/109
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acer Aspire needs to be added to nomux blacklist, otherwise the touchpad
misbehaves rather randomly.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If we receive EC interrupts after the cros_ec driver has probed, but
before the cros_ec_keyb driver has probed, the cros_ec IRQ handler
will not run the cros_ec_keyb notifier and the EC will leave the IRQ
line asserted. The cros_ec IRQ handler then returns IRQ_HANDLED and
the resulting flood of interrupts causes the machine to hang.
Since the EC interrupt is currently only used for the keyboard, move
the setup and handling of the EC interrupt to the cros_ec_keyb driver.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Remove the three wrapper functions that talk to the EC without passing all
the desired arguments and just use the underlying communication function
that passes everything in a struct intead.
This is internal code refactoring only. Nothing should change.
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the attribute groups of the led-class to create the time attribute
during probe in order to avoid racing with userspace.
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
In the hopes that people run new kernels on their devices, let's add a
warning message asking users to have their DTS file fixed.
The goal is that by Linux 4.0 we will be able to remove support for the
bogus version of our touchscreen's DTS.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Historically we dealt with touch_max equals to 2 differently from
other MT devices. Now we use input_mt_*() to process all MT events,
as long as touch_max is greater than 1. So, there is no need to
take (touch_max == 2) as a special case any more.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"A big update to the Atmel touchscreen driver, devm support for polled
input devices, several drivers have been converted to using managed
resources, and assorted driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (87 commits)
Input: synaptics - fix resolution for manually provided min/max
Input: atmel_mxt_ts - fix invalid return from mxt_get_bootloader_version
Input: max8997_haptic - add error handling for regulator and pwm
Input: elantech - don't set bit 1 of reg_10 when the no_hw_res quirk is set
Input: elantech - deal with clickpads reporting right button events
Input: edt-ft5x06 - fix an i2c write for M09 support
Input: omap-keypad - remove platform data support
ARM: OMAP2+: remove unused omap4-keypad file and code
Input: ab8500-ponkey - switch to using managed resources
Input: max8925_onkey - switch to using managed resources
Input: 88pm860x-ts - switch to using managed resources
Input: 88pm860x_onkey - switch to using managed resources
Input: intel-mid-touch - switch to using managed resources
Input: wacom - process outbound for newer Cintiqs
Input: wacom - set stylus_in_proximity when pen is in range
DTS: ARM: OMAP3-N900: Add tsc2005 support
Input: tsc2005 - add DT support
Input: add common DT binding for touchscreens
Input: jornada680_kbd - switch top using managed resources
Input: adp5520-keys - switch to using managed resources
...
commit 421e08c41f fixed the reported min/max for the X and Y axis,
but unfortunately, it broke the resolution of those same axis.
On the t540p, the resolution is the same regarding X and Y. It is not
a problem for xf86-input-synaptics because this driver is only interested
in the ratio between X and Y.
Unfortunately, xf86-input-cmt uses directly the resolution, and having a
null resolution leads to some divide by 0 errors, which are translated by
-infinity in the resulting coordinates.
Reported-by: Peter Hutterer <peter.hutterer@who-t.net>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's start checking return value of regulator_enable and pwm_enable to
avoid errors. Fixes the following warning:
drivers/input/misc/max8997_haptic.c:185:19: warning: ignoring return value of ‘regulator_enable’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchpad on the GIGABYTE U2442 not only stops communicating when we try
to set bit 3 (enable real hardware resolution) of reg_10, but on some BIOS
versions also when we set bit 1 (enable two finger mode auto correct).
I've asked the original reporter of:
https://bugzilla.kernel.org/show_bug.cgi?id=61151
To check that not setting bit 1 does not lead to any adverse effects on his
model / BIOS revision, and it does not, so this commit fixes the touchpad
not working on these versions by simply never setting bit 1 for laptop
models with the no_hw_res quirk.
Reported-and-tested-by: James Lademann <jwlademann@gmail.com>
Tested-by: Philipp Wolfer <ph.wolfer@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
At least the Dell Vostro 5470 elantech *clickpad* reports right button
clicks when clicked in the right bottom area:
https://bugzilla.redhat.com/show_bug.cgi?id=1103528
This is different from how (elantech) clickpads normally operate, normally
no matter where the user clicks on the pad the pad always reports a left
button event, since there is only 1 hardware button beneath the path.
It looks like Dell has put 2 buttons under the pad, one under each bottom
corner, causing this.
Since this however still clearly is a real clickpad hardware-wise, we still
want to report it as such to userspace, so that things like finger movement
in the bottom area can be properly ignored as it should be on clickpads.
So deal with this weirdness by simply mapping a right click to a left click
on elantech clickpads. As an added advantage this is something which we can
simply do on all elantech clickpads, so no need to add special quirks for
this weird model.
Reported-and-tested-by: Elder Marco <eldermarco@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver sends 3 bytes instead of 2 when accessing a register on the M09
firmware, so writing to gain seems to overflow into the offset register.
Signed-off-by: Robert Woerle <robert@linuxdevelopment.de>
Acked-By: Simon Budig <simon.budig@kernelconcepts.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support for
big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation and
moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as most
of the other v7 platforms in the tree. \o/ The work isn't quite complete,
there's some driver fixes still needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
Plus a large set of various smaller updates for different platforms. I'm
probably missing some important one here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJTjOKWAAoJEIwa5zzehBx36aEP/2vTD7x9FC59FACNHJ8iO7aw
0ebTgBBjI1Np6X18O+M7URbxV5TaBgwpUm/NDN86p03MpQ2eOXr8r47qVxe/HhZs
AdlTvzgE6QwxcVL/HeCKKUEN3BPH74+TZgFl9I5aSzNjpR39xETeK1aWP/ZiAl/q
/lGRZAQ59+c7Ung00Hg0g2YDxH9WFpK50Nj90ROnyjKSFkhIYngXYVpZB3maOypq
Pgib/U8IraKZ52oGJw3yinSoORr7FdcUdAGWGTz/lQdNL/jYDfQ6GkRW2oblWXdt
3Xvj9UW6NmkbMICucMvFuuW1nXAgutZuTp9w7mBxsiUlYepxPv/DXM6yiI1WGlEb
BeVOmOreNeN2nT6avv/uUhk3Osq63Jn9x8cz5y+7/lgWQwllh3/c+G01RotvgJEQ
vpQq5ps9fMxIAMaNP6N/YqMJI1IOrBj0iXxaZEDw3VYM/k4lSvtb3VXP9c/rqApu
U4i6hpSIGzrraU4NrjndYPndcLeNOVZbByETQKosZXuCo6G1sb7FstNSkzI9vSo8
O/pujIVUfYyBW82GzZGDw+aa7DWA29FPeUQ3p+sj5MSCg051xXT8h6QwqMo2K/zY
5ATs/qo6w7zH/Ou9rtHTRynCIb0GQJThDSlWtuXFedUF9quEltS+TDz/2o+dWtGJ
yBFGKDRuBB20D36w9xqg
=6LYI
-----END PGP SIGNATURE-----
Merge tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
Pull input subsystem fixes from Dmitry Torokhov:
"A couple of driver/build fixups and also redone quirk for Synaptics
touchpads on Lenovo boxes (now using PNP IDs instead of DMI data to
limit number of quirks)"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - change min/max quirk table to pnp-id matching
Input: synaptics - add a matches_pnp_id helper function
Input: synaptics - T540p - unify with other LEN0034 models
Input: synaptics - add min/max quirk for the ThinkPad W540
Input: ambakmi - request a shared interrupt for AMBA KMI devices
Input: pxa27x-keypad - fix generating scancode
Input: atmel-wm97xx - only build for AVR32
Input: fix ps2/serio module dependency
This is unused since all users (OMAP4/5) are DT only.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
New Cintiq tablets have a 200 tablet counts outside of screen area.
Add x/y_min for ABS_X/Y to pass this information to userland.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Jason Gerecke <killertofu@gmail.com>
Tested-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
