identify_cpu() is used to identify both the boot CPU and secondary
CPUs, but it performs some actions which only apply to the boot CPU.
Those functions are therefore really __init functions, but because
they're called by identify_cpu(), they must be marked __cpuinit.
This patch splits identify_cpu() into identify_boot_cpu() and
identify_secondary_cpu(), and calls the appropriate init functions
from each. Also, identify_boot_cpu() and all the functions it
dominates are marked __init.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Most of asm-i386/bugs.h is code which should be in a C file, so put it there.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
As per i386 patch: move X86_EFLAGS_IF et al out to a new header:
processor-flags.h, so we can include it from irqflags.h and use it in
raw_irqs_disabled_flags().
As a side-effect, we could now use these flags in .S files.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Under CONFIG_DISCONTIGMEM, assuming that a !pfn_valid() implies all
subsequent pfn-s are also invalid is wrong. Thus replace this by
explicitly checking against the E820 map.
AK: make e820 on x86-64 not initdata
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Rather than using a single constant PERCPU_ENOUGH_ROOM, compute it as
the sum of kernel_percpu + PERCPU_MODULE_RESERVE. This is now common
to all architectures; if an architecture wants to set
PERCPU_ENOUGH_ROOM to something special, then it may do so (ia64 is
the only one which does).
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
machine_ops is an interface for the machine_* functions defined in
<linux/reboot.h>. This is intended to allow hypervisors to intercept
the reboot process, but it could be used to implement other x86
subarchtecture reboots.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Add a smp_ops interface. This abstracts the API defined by
<linux/smp.h> for use within arch/i386. The primary intent is that it
be used by a paravirtualizing hypervisor to implement SMP, but it
could also be used by non-APIC-using sub-architectures.
This is related to CONFIG_PARAVIRT, but is implemented unconditionally
since it is simpler that way and not a highly performance-sensitive
interface.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Now we have an explicit per-cpu GDT variable, we don't need to keep the
descriptors around to use them to find the GDT: expose cpu_gdt directly.
We could go further and make load_gdt() pack the descriptor for us, or even
assume it means "load the current cpu's GDT" which is what it always does.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
- there's no reason for duplicating the prototype from
include/linux/syscalls.h in include/asm-x86_64/unistd.h
- every file should #include the headers containing the prototypes for
it's global functions
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andi Kleen <ak@suse.de>
x86_64 currently simulates a list using the index and private fields of the
page struct. Seems that the code was inherited from i386. But x86_64 does
not use the slab to allocate pgds and pmds etc. So the lru field is not
used by the slab and therefore available.
This patch uses standard list operations on page->lru to realize pgd
tracking.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Move X86_EFLAGS_IF et al out to a new header: processor-flags.h, so we
can include it from irqflags.h and use it in raw_irqs_disabled_flags().
As a side-effect, we could now use these flags in .S files.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
On x86-64, kernel memory freed after init can be entirely unmapped instead
of just getting 'poisoned' by overwriting with a debug pattern.
On i386 and x86-64 (under CONFIG_DEBUG_RODATA), kernel text and bug table
can also be write-protected.
Compared to the first version, this one prevents re-creating deleted
mappings in the kernel image range on x86-64, if those got removed
previously. This, together with the original changes, prevents temporarily
having inconsistent mappings when cacheability attributes are being
changed on such pages (e.g. from AGP code). While on i386 such duplicate
mappings don't exist, the same change is done there, too, both for
consistency and because checking pte_present() before using various other
pte_XXX functions is a requirement anyway. At once, i386 code gets
adjusted to use pte_huge() instead of open coding this.
AK: split out cpa() changes
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Fix various broken corner cases in i386 and x86-64 change_page_attr.
AK: split off from tighten kernel image access rights
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
paravirt.c used to implement native versions of all low-level
functions. Far cleaner is to have the native versions exposed in the
headers and as inline native_XXX, and if !CONFIG_PARAVIRT, then simply
#define XXX native_XXX.
There are several nice side effects:
1) write_dt_entry() now takes the correct "struct Xgt_desc_struct *"
not "void *".
2) load_TLS is reintroduced to the for loop, not manually unrolled
with a #error in case the bounds ever change.
3) Macros become inlines, with type checking.
4) Access to the native versions is trivial for KVM, lguest, Xen and
others who might want it.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
We now have cpu_init() and secondary_cpu_init() doing nothing but calling
_cpu_init() with the same arguments. Rename _cpu_init() to cpu_init() and use
it as a replcement for secondary_cpu_init().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Now we are no longer dynamically allocating the GDT, we don't need the
"cpu_gdt_table" at all: we can switch straight from "boot_gdt_table" to the
per-cpu GDT. This means initializing the cpu_gdt array in C.
The boot CPU uses the per-cpu var directly, then in smp_prepare_cpus() it
switches to the per-cpu copy just allocated. For secondary CPUs, the
early_gdt_descr is set to point directly to their per-cpu copy.
For UP the code is very simple: it keeps using the "per-cpu" GDT as per SMP,
but we never have to move.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Allocating PDA and GDT at boot is a pain. Using simple per-cpu variables adds
happiness (although we need the GDT page-aligned for Xen, which we do in a
followup patch).
[akpm@linux-foundation.org: build fix]
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
The specific case I am encountering is kdump under Xen with a 64 bit
hypervisor and 32 bit kernel/userspace. The dump created is 64 bit due to
the hypervisor but the dump kernel is 32 bit for maximum compatibility.
It's possibly less likely to be useful in a purely native scenario but I
see no reason to disallow it.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Ian Campbell <ian.campbell@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Horms <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
GCC (4.1 at least) unrolls it anyway, but I can't believe this code
was ever justifiable. (I've also submitted a patch which cleans up
i386, which is even uglier).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Whenever we schedule, __switch_to calls load_esp0 which does:
tss->esp0 = thread->esp0;
This is never initialized for the initial thread (ie "swapper"), so when we're
scheduling that, we end up setting esp0 to 0. This is fine: the swapper never
leaves ring 0, so this field is never used.
lguest, however, gets upset that we're trying to used an unmapped page as our
kernel stack. Rather than work around it there, let's initialize it.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Extends the numa=fake x86_64 command-line option to allow for configurable
node sizes. These nodes can be used in conjunction with cpusets for coarse
memory resource management.
The old command-line option is still supported:
numa=fake=32 gives 32 fake NUMA nodes, ignoring the NUMA setup of the
actual machine.
But now you may configure your system for the node sizes of your choice:
numa=fake=2*512,1024,2*256
gives two 512M nodes, one 1024M node, two 256M nodes, and
the rest of system memory to a sixth node.
The existing hash function is maintained to support the various node sizes
that are possible with this implementation.
Each node of the same size receives roughly the same amount of available
pages, regardless of any reserved memory with its address range. The total
available pages on the system is calculated and divided by the number of equal
nodes to allocate. These nodes are then dynamically allocated and their
borders extended until such time as their number of available pages reaches
the required size.
Configurable node sizes are recommended when used in conjunction with cpusets
for memory control because it eliminates the overhead associated with scanning
the zonelists of many smaller full nodes on page_alloc().
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Paul Jackson <pj@sgi.com>
Cc: Christoph Lameter <clameter@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Change mark_tsc_unstable() so it takes a string argument, which holds the
reason the TSC was marked unstable.
This is then displayed the first time mark_tsc_unstable is called.
This should help us better debug why the TSC was marked unstable on certain
systems and allow us to make sure we're not being overly paranoid when
throwing out this troublesome clocksource.
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
o Modpost generates warnings for i386 if compiled with CONFIG_RELOCATABLE=y
WARNING: vmlinux - Section mismatch: reference to .init.text:find_unisys_acpi_oem_table from .text between 'acpi_madt_oem_check' (at offset 0xc0101eda) and 'enable_apic_mode'
WARNING: vmlinux - Section mismatch: reference to .init.text:acpi_get_table_header_early from .text between 'acpi_madt_oem_check' (at offset 0xc0101ef0) and 'enable_apic_mode'
WARNING: vmlinux - Section mismatch: reference to .init.text:parse_unisys_oem from .text between 'acpi_madt_oem_check' (at offset 0xc0101f2e) and 'enable_apic_mode'
WARNING: vmlinux - Section mismatch: reference to .init.text:setup_unisys from .text between 'acpi_madt_oem_check' (at offset 0xc0101f37) and 'enable_apic_mode'WARNING: vmlinux - Section mismatch: reference to .init.text:parse_unisys_oem from .text between 'mps_oem_check' (at offset 0xc0101ec7) and 'acpi_madt_oem_check'
WARNING: vmlinux - Section mismatch: reference to .init.text:es7000_sw_apic from .text between 'enable_apic_mode' (at offset 0xc0101f48) and 'check_apicid_present'
o Some functions which are inline (acpi_madt_oem_check) are not inlined by
compiler as these functions are accessed using function pointer. These
functions are put in .text section and they in-turn access __init type
functions hence modpost generates warnings.
o Do not iniline acpi_madt_oem_check, instead make it __init.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Enable system hashtable memory to be distributed among nodes on x86_64 NUMA
Forcing the kernel to use node interleaved vmalloc instead of bootmem for
the system hashtable memory (alloc_large_system_hash) reduces the memory
imbalance on node 0 by around 40MB on a 8 node x86_64 NUMA box:
Before the following patch, on bootup of a 8 node box:
Node 0 MemTotal: 3407488 kB
Node 0 MemFree: 3206296 kB
Node 0 MemUsed: 201192 kB
Node 0 Active: 7012 kB
Node 0 Inactive: 512 kB
Node 0 Dirty: 0 kB
Node 0 Writeback: 0 kB
Node 0 FilePages: 1912 kB
Node 0 Mapped: 420 kB
Node 0 AnonPages: 5612 kB
Node 0 PageTables: 468 kB
Node 0 NFS_Unstable: 0 kB
Node 0 Bounce: 0 kB
Node 0 Slab: 5408 kB
Node 0 SReclaimable: 644 kB
Node 0 SUnreclaim: 4764 kB
After the patch (or using hashdist=1 on the kernel command line):
Node 0 MemTotal: 3407488 kB
Node 0 MemFree: 3247608 kB
Node 0 MemUsed: 159880 kB
Node 0 Active: 3012 kB
Node 0 Inactive: 616 kB
Node 0 Dirty: 0 kB
Node 0 Writeback: 0 kB
Node 0 FilePages: 2424 kB
Node 0 Mapped: 380 kB
Node 0 AnonPages: 1200 kB
Node 0 PageTables: 396 kB
Node 0 NFS_Unstable: 0 kB
Node 0 Bounce: 0 kB
Node 0 Slab: 6304 kB
Node 0 SReclaimable: 1596 kB
Node 0 SUnreclaim: 4708 kB
I guess it is a good idea to keep HASHDIST_DEFAULT "on" for x86_64 NUMA
since x86_64 has no dearth of vmalloc space? Or maybe enable hash
distribution for all 64bit NUMA arches? The following patch does it only
for x86_64.
I ran a HPC MPI benchmark -- 'Ansys wingsolid', which takes up quite a bit of
memory and uses up tlb entries. This was on a 4 way, 2 socket
Tyan AMD box (non vsmp), with 8G total memory (4G pernode).
The results with and without hash distribution are:
1. Vanilla - runtime of 1188.000s
2. With hashdist=1 runtime of 1154.000s
Oprofile output for the duration of run is:
1. Vanilla:
PU: AMD64 processors, speed 2411.16 MHz (estimated)
Counted L1_AND_L2_DTLB_MISSES events (L1 and L2 DTLB misses) with a unit
mask of 0x00 (No unit mask) count 500
samples % app name symbol name
163054 6.5513 libansys1.so MultiFront::decompose(int, int,
Elemset *, int *, int, int, int)
162061 6.5114 libansys3.so blockSaxpy6L_fd
162042 6.5107 libansys3.so blockInnerProduct6L_fd
156286 6.2794 libansys3.so maxb33_
87879 3.5309 libansys1.so elmatrixmultpcg_
84857 3.4095 libansys4.so saxpy_pcg
58637 2.3560 libansys4.so .st4560
46612 1.8728 libansys4.so .st4282
43043 1.7294 vmlinux-t copy_user_generic_string
41326 1.6604 libansys3.so blockSaxpyBackSolve6L_fd
41288 1.6589 libansys3.so blockInnerProductBackSolve6L_fd
2. With hashdist=1
CPU: AMD64 processors, speed 2411.13 MHz (estimated)
Counted L1_AND_L2_DTLB_MISSES events (L1 and L2 DTLB misses) with a unit
mask of 0x00 (No unit mask) count 500
samples % app name symbol name
162993 6.9814 libansys1.so MultiFront::decompose(int, int,
Elemset *, int *, int, int, int)
160799 6.8874 libansys3.so blockInnerProduct6L_fd
160459 6.8729 libansys3.so blockSaxpy6L_fd
156018 6.6826 libansys3.so maxb33_
84700 3.6279 libansys4.so saxpy_pcg
83434 3.5737 libansys1.so elmatrixmultpcg_
58074 2.4875 libansys4.so .st4560
46000 1.9703 libansys4.so .st4282
41166 1.7632 libansys3.so blockSaxpyBackSolve6L_fd
41033 1.7575 libansys3.so blockInnerProductBackSolve6L_fd
35762 1.5318 libansys1.so inner_product_sub
35591 1.5245 libansys1.so inner_product_sub2
28259 1.2104 libansys4.so addVectors
Signed-off-by: Pravin B. Shelar <pravin.shelar@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Christoph Lameter <clameter@engr.sgi.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Fix for the following patch. Provide dummy cpufreq functions when
CPUFREQ is not compiled in.
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
o X86_64 kernel should run from 2MB aligned address for two reasons.
- Performance.
- For relocatable kernels, page tables are updated based on difference
between compile time address and load time physical address.
This difference should be multiple of 2MB as kernel text and data
is mapped using 2MB pages and PMD should be pointing to a 2MB
aligned address. Life is simpler if both compile time and load time
kernel addresses are 2MB aligned.
o Flag the error at compile time if one is trying to build a kernel which
does not meet alignment restrictions.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This patch modifies the x86_64 kernel so that it can be loaded and run
at any 2M aligned address, below 512G. The technique used is to
compile the decompressor with -fPIC and modify it so the decompressor
is fully relocatable. For the main kernel the page tables are
modified so the kernel remains at the same virtual address. In
addition a variable phys_base is kept that holds the physical address
the kernel is loaded at. __pa_symbol is modified to add that when
we take the address of a kernel symbol.
When loaded with a normal bootloader the decompressor will decompress
the kernel to 2M and it will run there. This both ensures the
relocation code is always working, and makes it easier to use 2M
pages for the kernel and the cpu.
AK: changed to not make RELOCATABLE default in Kconfig
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Currently __pa_symbol is for use with symbols in the kernel address
map and __pa is for use with pointers into the physical memory map.
But the code is implemented so you can usually interchange the two.
__pa which is much more common can be implemented much more cheaply
if it is it doesn't have to worry about any other kernel address
spaces. This is especially true with a relocatable kernel as
__pa_symbol needs to peform an extra variable read to resolve
the address.
There is a third macro that is added for the vsyscall data
__pa_vsymbol for finding the physical addesses of vsyscall pages.
Most of this patch is simply sorting through the references to
__pa or __pa_symbol and using the proper one. A little of
it is continuing to use a physical address when we have it
instead of recalculating it several times.
swapper_pgd is now NULL. leave_mm now uses init_mm.pgd
and init_mm.pgd is initialized at boot (instead of compile time)
to the physmem virtual mapping of init_level4_pgd. The
physical address changed.
Except for the for EMPTY_ZERO page all of the remaining references
to __pa_symbol appear to be during kernel initialization. So this
should reduce the cost of __pa in the common case, even on a relocated
kernel.
As this is technically a semantic change we need to be on the lookout
for anything I missed. But it works for me (tm).
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
With the rewrite of the SMP trampoline and the early page
allocator there is nothing that needs identity mapped pages,
once we start executing C code.
So add zap_identity_mappings into head64.c and remove
zap_low_mappings() from much later in the code. The functions
are subtly different thus the name change.
This also kills boot_level4_pgt which was from an earlier
attempt to move the identity mappings as early as possible,
and is now no longer needed. Essentially I have replaced
boot_level4_pgt with trampoline_level4_pgt in trampoline.S
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
o Use appropriate names for 64bit regsiters.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
EFER varies like %cr4 depending on the cpu capabilities, and which cpu
capabilities we want to make use of. So save/restore it make certain
we have the same EFER value when we are done.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Move __KERNEL32_CS up into the unused gdt entry. __KERNEL32_CS is
used when entering the kernel so putting it first is useful when
trying to keep boot gdt sizes to a minimum.
Set the accessed bit on all gdt entries. We don't care
so there is no need for the cpu to burn the extra cycles,
and it potentially allows the pages to be immutable. Plus
it is confusing when debugging and your gdt entries mysteriously
change.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
- Merge physmem_pgt and ident_pgt, removing physmem_pgt. The merge
is broken as soon as mm/init.c:init_memory_mapping is run.
- As physmem_pgt is gone don't export it in pgtable.h.
- Use defines from pgtable.h for page permissions.
- Fix the physical memory identity mapping so it is at the correct
address.
- Remove the physical memory mapping from wakeup_level4_pgt it
is at the wrong address so we can't possibly be usinging it.
- Simply NEXT_PAGE the work to calculate the phys_ alias
of the labels was very cool. Unfortuantely it was a brittle
special purpose hack that makes maitenance more difficult.
Instead just use label - __START_KERNEL_map like we do
everywhere else in assembly.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
This patch makes pgtable.h and page.h safe to include
in assembly files like head.S. Allowing us to use
symbolic constants instead of hard coded numbers when
refering to the page tables.
This patch copies asm-sparc64/const.h to asm-x86_64 to
get a definition of _AC() a very convinient macro that
allows us to force the type when we are compiling the
code in C and to drop all of the type information when
we are using the constant in assembly. Previously this
was done with multiple definition of the same constant.
const.h was modified slightly so that it works when given
CONFIG options as arguments.
This patch adds #ifndef __ASSEMBLY__ ... #endif
and _AC(1,UL) where appropriate so the assembler won't
choke on the header files. Otherwise nothing
should have changed.
AK: added const.h to exported headers to fix headers_check
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The dma_ops structure can be const since it never changes
after boot.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
On Tue, Mar 13, 2007 at 05:33:09AM -0700, Randy.Dunlap wrote:
> On Tue, 13 Mar 2007, Glauber de Oliveira Costa wrote:
>
> > Tiny cleanup:
> >
> > In x86_64, the same functions for reading cr3 and writing cr{3,4} are
> > defined in tlbflush.h and system.h, whith just a name change.
> > The only difference is the clobbering of memory, which seems a safe, and
> > even needed change for the write_cr4. This patch removes the duplicate.
> > write_cr3() is moved to system.h for consistency.
>
> missing patch.....
>
thanks. Attached now
--
Glauber de Oliveira Costa
Red Hat Inc.
"Free as in Freedom"
Signed-off-by: Andi Kleen <ak@suse.de>
The set_seg_base function isn't used anywhere (2.6.21-rc3-git1)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
The reboot_fixups stuff seems to be a bit of a mess, specifically the
header is in linux/ when its a purely i386-specific piece of code. I'm
not sure why it has its config option; its only currently needed for
"geode-gx1/cs5530a", so perhaps whatever config option controls that
hardware should enable this?
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Explicity specify that the caller should pin the user memory
otherwise the function will sleep
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@gmail.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Change sysenter_setup to __cpuinit.
Change __INIT & __INITDATA to be cpu hotplug aware.
Resolve MODPOST warnings similar to:
WARNING: vmlinux - Section mismatch: reference to .init.text:sysenter_setup from
.text between 'identify_cpu' (at offset 0xc040a380) and 'detect_ht'
and
WARNING: vmlinux - Section mismatch: reference to .init.data:vsyscall_int80_end
from .text between 'sysenter_setup' (at offset 0xc041a269) and 'enable_sep_cpu'
WARNING: vmlinux - Section mismatch: reference to
.init.data:vsyscall_int80_start from .text between 'sysenter_setup' (at offset
0xc041a26e) and 'enable_sep_cpu'
WARNING: vmlinux - Section mismatch: reference to
.init.data:vsyscall_sysenter_end from .text between 'sysenter_setup' (at offset
0xc041a275) and 'enable_sep_cpu'
WARNING: vmlinux - Section mismatch: reference to
.init.data:vsyscall_sysenter_start from .text between 'sysenter_setup' (at
offset 0xc041a27a) and 'enable_sep_cpu'
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
The VIA C7 is a 686 (with TSC) that supports MMX, SSE and SSE2, it also has
a cache line length of 64 according to
http://www.digit-life.com/articles2/cpu/rmma-via-c7.html. This patch sets
gcc to -march=686 and select s the correct cache shift.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@suse.de>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Eliminated the arch/i386/kernel/timers in 2.6.18, use clocksoures instead.
pit_latch_buggy was referred in timers/timer_tsc.c, and currently removed.
Therefore nobody refer it.
Until 2.6.17, MediaGX's TSC works correctly. after 2.6.18, warned "TSC
appears to be running slowly. Marking it as unstable". So marked unstable
TSC when CS55x0.
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andi Kleen <ak@suse.de>
No need to use -traditional for processing asm in i386/kernel/
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Synchronize i386's smp_send_stop() with x86-64's in only try-locking
the call lock to prevent deadlocks when called from panic().
In both version, disable interrupts before clearing the CPU off the
online map to eliminate races with IRQ handlers inspecting this map.
Also in both versions, save/restore interrupts rather than disabling/
enabling them.
On x86-64, eliminate one function used here by folding it into its
single caller, convert to static, and rename for consistency with i386
(lkcd may like this).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Avoid including asm/vsyscall32.h in virtually every source file.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Move inclusion of asm/fixmap.h to where it is really used rather than
where it may have been used long ago (requires a few other adjustments
to includes due to previous implicit dependencies).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Remove clustered APIC mode. There's little point in the use of clustered APIC
mode, broadcasting is limited to within the cluster only, and chipsets have
bugs in this area as well. So default to physical APIC mode when the CPU
count is large, and default to logical APIC mode when the CPU count is 8 or
smaller.
(this patch only removes the use of genapic_cluster and cleans up the
resulting genapic.c file - removal of all remaining traces of clustered
mode will be done by another patch.)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
This patch adds ablkcipher_request_set_tfm for those users that need
to manage the memory for ablkcipher requests directly.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the cryptd module which is a template that takes a
synchronous software crypto algorithm and converts it to an asynchronous
one by executing it in a kernel thread.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As it is whenever a new algorithm with the same name is registered
users of the old algorithm will be removed so that they can take
advantage of the new algorithm. This presents a problem when the
new algorithm is not equivalent to the old algorithm. In particular,
the new algorithm might only function on top of the existing one.
Hence we should not remove users unless they can make use of the
new algorithm.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the mid-level interface for asynchronous block ciphers.
It also includes a generic queueing mechanism that can be used by other
asynchronous crypto operations in future.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch passes the type/mask along when constructing instances of
templates. This is in preparation for templates that may support
multiple types of instances depending on what is requested. For example,
the planned software async crypto driver will use this construct.
For the moment this allows us to check whether the instance constructed
is of the correct type and avoid returning success if the type does not
match.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds the frontend interface for asynchronous block ciphers.
In addition to the usual block cipher parameters, there is a callback
function pointer and a data pointer. The callback will be invoked only
if the encrypt/decrypt handlers return -EINPROGRESS. In other words,
if the return value of zero the completion handler (or the equivalent
code) needs to be invoked by the caller.
The request structure is allocated and freed by the caller. Its size
is determined by calling crypto_ablkcipher_reqsize(). The helpers
ablkcipher_request_alloc/ablkcipher_request_free can be used to manage
the memory for a request.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This is a very simple bitbanging I2C bus driver utilizing the new
arch-neutral GPIO API. Useful for chips that don't have a built-in
I2C controller, additional I2C busses, or testing purposes.
To use, include something similar to the following in the
board-specific setup code:
#include <linux/i2c-gpio.h>
static struct i2c_gpio_platform_data i2c_gpio_data = {
.sda_pin = GPIO_PIN_FOO,
.scl_pin = GPIO_PIN_BAR,
};
static struct platform_device i2c_gpio_device = {
.name = "i2c-gpio",
.id = 0,
.dev = {
.platform_data = &i2c_gpio_data,
},
};
Register this platform_device, set up the I2C pins as GPIO if
required and you're ready to go. This will use default values for
udelay and timeout, and will work with GPIO hardware that does not
support open drain mode, but allows sensing of the SDA and SCL lines
even when they are being driven.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add back the i2c_smbus_read_block_data helper function, it is needed
by the upcoming lm93 hardware monitoring driver and possibly others.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The original i2c-algo-bit implementation uses a 33/66 SCL duty cycle
when bits are being written on the bus. While the I2C specification
doesn't forbid it, this prevents us from driving the I2C bus to its
max speed, limiting us to 66 kbps max on standard I2C busses.
Implementing a 50/50 duty cycle instead lets us max out the bandwidth
up to the theoretical max of 100 kbps on standard I2C busses. This is
particularly important when large amounts of data need to be transfered
over the bus, as is the case with some TV adapters when the firmware is
being uploaded.
In fact this change even allows, at least in theory, fast-mode I2C
support at 125, 166 and 250 kbps. There's no way to reach the
theoretical max of 400 kbps with this implementation. But I don't
think we want to put efforts in that direction anyway: software-driven
I2C is very CPU-intensive and bad for latency.
Other timing changes:
* Don't set SDA high explicitly on error, we're going to issue a stop
condition before we leave anyway.
* If an error occurs when sending the slave address, yield the CPU
before retrying, and remove the additional delay after the new start
condition.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The i2c linux driver for blackfin architecture which supports blackfin
on-chip TWI controller i2c operation.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Reviewed-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Make i2c_del_driver a void function, like all other driver removal
functions. It always returned 0 even when errors occured, and nobody
ever actually checked the return value anyway. And we cannot fail
a module removal anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Move the declaration of i2c-isa-only exported symbols to i2c-isa
itself, that's the best way to ensure nobody will attempt to use them.
Hopefully we'll get rid of the exports themselves soon anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add a new helper function to instantiate an i2c device. It is meant as a
replacement for i2c_new_device() when you don't know for sure at which
address your I2C/SMBus device lives. This happens frequently on TV
adapters for example, you know there is a tuner chip on the bus, but
depending on the exact board model and revision, it can live at different
addresses. So, the new i2c_new_probed_device() function will probe the bus
according to a list of addresses, and as soon as one of these addresses
responds, it will call i2c_new_device() on that one address.
This function will make it possible to port the old i2c drivers to the
new model quickly.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add i2c_bit_add_numbered_bus(), which is equivalent to i2c_bit_add_bus
except that it calls i2c_add_numbered_adapter() at the end instead of
i2c_add_adapter().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This adds a call, i2c_add_numbered_adapter(), registering an I2C adapter
with a specific bus number and then creating I2C device nodes for any
pre-declared devices on that bus. It builds on previous patches adding
I2C probe() and remove() support, and that pre-declaration of devices.
This completes the core support for "new style" I2C device drivers.
Those follow the standard driver model for binding devices to drivers
(using probe and remove methods) rather than a legacy model (where the
driver tries to autoconfigure each bus, and registers devices itself).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This provides partial support for new-style I2C driver binding. It builds
on "struct i2c_board_info" declarations that identify I2C devices on a given
board. This is needed on systems with I2C devices that can't be fully probed
and/or autoconfigured, such as many embedded Linux configurations where the
way a given I2C device is wired may affect how it must be used.
There are two models for declaring such devices:
* LATE -- using a public function i2c_new_device(). This lets modules
declare I2C devices found *AFTER* a given I2C adapter becomes available.
For example, a PCI card could create adapters giving access to utility
chips on that card, and this would be used to associate those chips with
those adapters.
* EARLY -- from arch_initcall() level code, using a non-exported function
i2c_register_board_info(). This copies the declarations *BEFORE* such
an i2c_adapter becomes available, arranging that i2c_new_device() will
be called later when i2c-core registers the relevant i2c_adapter.
For example, arch/.../.../board-*.c files would declare the I2C devices
along with their platform data, and I2C devices would behave much like
PNPACPI devices. (That is, both enumerate from board-specific tables.)
To match the exported i2c_new_device(), the previously-private function
i2c_unregister_device() is now exported.
Pending later patches using these new APIs, this is effectively a NOP.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
More update for new style driver support: add a remove() method, and
use it in the relevant code paths.
Again, nothing will use this yet since there's nothing to create devices
feeding this infrastructure.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
One of a series of I2C infrastructure updates to support enumeration using
the standard Linux driver model.
This patch updates probe() and associated hotplug/coldplug support, but
not remove(). Nothing yet _uses_ it to create I2C devices, so those
hotplug/coldplug mechanisms will be the only externally visible change.
This patch will be an overall NOP since the I2C stack doesn't yet create
clients/devices except as part of binding them to legacy drivers.
Some code is moved earlier in the source code, helping group more of the
per-device infrastructure in one place and simplifying handling per-device
attributes.
Terminology being adopted: "legacy drivers" create devices (i2c_client)
themselves, while "new style" ones follow the driver model (the i2c_client
is handed to the probe routine). It's an either/or thing; the two models
don't mix, and drivers that try mixing them won't even be registered.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the I2C bus drivers emulate the SMBus Block Read and Block Process
Call transactions if they wish. This requires to define a new message
flag, which i2c-core will use to let the underlying I2C bus driver
know that the first received byte will specify the length of the read
message.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Rename dev_to_i2c_adapter() as to_i2c_adapter(), since the previous
syntax was a surprising and needless difference from normal naming
conventions in Linux.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This shrinks the size of "struct i2c_client" by 40 bytes:
- Substantially shrinks the string used to identify the chip type
- The "flags" don't need to be so big
- Removes some internal padding
It also adds kerneldoc for that struct, explaining how "name" is really a
chip type identifier; it's otherwise potentially confusing.
Because the I2C_NAME_SIZE symbol was abused for both i2c_client.name
and for i2c_adapter.name, this needed to affect i2c_adapter too. The
adapters which used that symbol now use the more-obviously-correct
idiom of taking the size of that field.
JD: Shorten i2c_adapter.name from 50 to 48 bytes while we're here, to
avoid wasting space in padding.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Kill i2c_adapter_driver as it doesn't make sense and it prevents
further i2c-core cleanups. i2c_adapter devices are virtual devices
(ex-class devices) and as such they don't need a driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Kill i2c_adapter.class_dev. Instead, set the class of i2c_adapter.dev
to i2c_adapter_class, so that a symlink will be created for every
i2c_adapter in /sys/class/i2c-adapter.
The same change must be mirrored to i2c-isa as it duplicates some
of the i2c-core functionalities.
User-space tools and libraries might need some adjustments. In
particular, libsensors from lm_sensors 2.10.3 or later is required for
proper discovery of i2c adapter names after this change.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
full kthread conversion on the voyager power switch handling thread.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix handling of low voltage MMC cards.
The latest MMC and SD specs both agree that support for
low-voltage operations is indicated by bit 7 in the OCR.
The MMC spec states that the low voltage range is
1.65-1.95V while the SD spec leaves the actual voltage
range undefined - meaning that there is still no such
thing as a low voltage SD card.
However, an old Sandisk spec implied that bits 7.0
represented voltages below 2.0V in 1V or 0.5V increments,
and the code was accordingly written with that expectation.
This confusion meant that host drivers attempting to support
the typical low voltage (1.8V) would set the wrong bits in
the host OCR mask (usually bits 5 and/or 6) resulting in the
the low voltage mode never being used.
This change corrects the low voltage range and adds sanity
checks on the reserved bits (0-6) and for SD cards that
claim to support low-voltage operations.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Consolidate the list of available voltages.
Up until now, a separate set of defines has been
used for host->vdd than that used for the OCR
voltage mask values. Having two sets of defines
allows them to get out of sync and the current
sets are already inconsistent with one claiming
to describe ranges and the other specific voltages.
Only the SDHCI driver uses the host->vdd defines and
it is easily fixed to use the OCR defines.
Signed-off-by: Philip Langdale <philipl@overt.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Delegate protocol handling to "bus handlers". This allows the core to
just handle the task of arbitrating the bus. Initialisation and
pampering of cards is now done by the different bus handlers.
This design also allows MMC and SD (and later SDIO) to be more cleanly
separated, allowing easier maintenance.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Move protocol operations and definitions into their own files
in an effort to separate protocol handling and bus
arbitration more clearly.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The classic MMC bus was defined as multi card bus
system, which is reflected in the design in the MMC
layer.
When SD showed up, the bus topology was abandoned
and a star topology (one card per host) was mandated.
MMC version 4 has followed this, officially deprecating
the bus topology.
As we do not have any known users of the bus
topology we can remove support for it. This will
simplify the code and rectify some incorrect
assumptions in the newer additions.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Make sure we kill of any pending detection runs when the host
is removed instead of when it is freed. Also add some debugging
to make sure the driver doesn't queue up more detection after it
has removed the host.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
All host drivers were #include:ing mmc/protocol.h just to
get access to the OCR bit defines. Move these to host.h instead.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support for MMC 4.2 sector based cards. This tweaks the init a
bit and reads a new field out of the EXT_CSD.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
It was found that delays associated with issue and completion of the commands
severely limit performance of the new, fast SD cards. To alleviate this issue
scatter-gather emulation in software is implemented for both dma and pio
transfer modes. Non-block aligned and high memory sg entries are accounted
for.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
State machine used to to track mmc command state was found to be fragile
and unreliable, making many cards unusable. The safer solution is to perform
all needed checks at every card event.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some details of the device management (create, add, remove) are really
belong to the tifm_core, as they are not hardware specific.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Some details of the adapter management (create, add, remove) are really
belong to the tifm_core, as they are not hardware specific.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Freezeable workqueue makes sure that adapter work items (device insertions
and removals) would be handled after the system is fully resumed. Previously
this was achieved by explicit freezing of the kthread.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Remove code duplicating the kernel functionality and clean up data
structures involved in driver matching.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Instead of passing transformed value of adapter interrupt status to
socket drivers, implement two separate callbacks - one for card events
and another for dma events.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
READDIRPLUS can be a performance hindrance when the client is working with
large directories. In addition, some servers still have bugs in their
implementations (e.g. Tru64 returns wrong values for the fsid).
Add a mount flag to enable users to turn it off at mount time following the
implementation in Apple's NFS client.
Signed-off-by: Steve Dickson <steved@redhat.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
net/sunrpc/pmap_clnt.c has been replaced by net/sunrpc/rpcb_clnt.c.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Introduce a replacement for the in-kernel portmapper client that supports
all 3 versions of the rpcbind protocol. This code is not used yet.
Original code by Groupe Bull updated for the latest kernel, with multiple
bug fixes.
Note that rpcb_clnt.c does not yet support registering via versions 3 and
4 of the rpcbind protocol. That is planned for a later patch.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently rpc_malloc sets req->rq_buffer internally. Make this a more
generic interface: return a pointer to the new buffer (or NULL) and
make the caller set req->rq_buffer and req->rq_bufsize. This looks much
more like kmalloc and eliminates the side effects.
To fix a potential deadlock, this patch also replaces GFP_NOFS with
GFP_NOWAIT in rpc_malloc. This prevents async RPCs from sleeping outside
the RPC's task scheduler while allocating their buffer.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
The RPC buffer size estimation logic in net/sunrpc/clnt.c always
significantly overestimates the requirements for the buffer size.
A little instrumentation demonstrated that in fact rpc_malloc was never
allocating the buffer from the mempool, but almost always called kmalloc.
To compute the size of the RPC buffer more precisely, split p_bufsiz into
two fields; one for the argument size, and one for the result size.
Then, compute the sum of the exact call and reply header sizes, and split
the RPC buffer precisely between the two. That should keep almost all RPC
buffers within the 2KiB buffer mempool limit.
And, we can finally be rid of RPC_SLACK_SPACE!
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
NLM version 4 requests estimate the call and reply header sizes rather
conservatively, using the very maximum size allowed in the protocol even
though Linux always uses only a small fraction of the allowable space.
Reduce the size of caller and lock arguments to conserve RPC buffer space
while XDR encoding NLM4 arguments. Add compile-time checks to ensure the
hostname string won't overflow NLM protocol maximums.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Currently we do write coalescing in a very inefficient manner: one pass in
generic_writepages() in order to lock the pages for writing, then one pass
in nfs_flush_mapping() and/or nfs_sync_mapping_wait() in order to gather
the locked pages for coalescing into RPC requests of size "wsize".
In fact, it turns out there is actually a deadlock possible here since we
only start I/O on the second pass. If the user signals the process while
we're in nfs_sync_mapping_wait(), for instance, then we may exit before
starting I/O on all the requests that have been queued up.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Do the coalescing of read requests into block sized requests at start of
I/O as we scan through the pages instead of going through a second pass.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
For backwards compatibility, call_platform_enable_wakeup() can return 0
instead of -EIO since we aren't guaranteed to have errno defined.
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a kvasprintf() function to complement kasprintf().
No in-tree users yet, but I have some coming up.
[akpm@linux-foundation.org: EXPORT it]
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Keir Fraser <keir@xensource.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the docs and behaviour from "all states valid" to "no
states valid" if no .valid callback is assigned. Users of pm_ops that only
need mem sleep can assign pm_valid_only_mem without any overhead, others
will require more elaborate callbacks.
Now that all users of pm_ops have a .valid callback this is a safe thing to
do and prevents things from getting messy again as they were before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Looks-okay-to: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all users of pm_ops only support mem sleep, don't check in .valid and
don't reject any others in .prepare so users can be confused if they check
/sys/power/state, especially when new states are added (these would then
result in s-t-r although they're supposed to be something different).
This patch implements a generic pm_valid_only_mem function that is then
exported for users and puts it to use in almost all existing pm_ops.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: linux-pm@lists.linux-foundation.org
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch removes the firmware disk suspend mode which is the wrong approach,
it is supposed to be used for implementing firmware-based disk suspend but
cannot actually be used for that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch series cleans up some misconceptions about pm_ops. Some users of
the pm_ops structure attempt to use it to stop the user from entering suspend
to disk, this, however, is not possible since the user can always use
"shutdown" in /sys/power/disk and then the pm_ops are never invoked. Also,
platforms that don't support suspend to disk simply should not allow
configuring SOFTWARE_SUSPEND (read the help text on it, it only selects
suspend to disk and nothing else, all the other stuff depends on PM).
The pm_ops structure is actually intended to provide a way to enter
platform-defined sleep states (currently supported states are "standby" and
"mem" (suspend to ram)) and additionally (if SOFTWARE_SUSPEND is configured)
allows a platform to support a platform specific way to enter low-power mode
once everything has been saved to disk. This is currently only used by ACPI
(S4).
This patch:
The pm_ops.pm_disk_mode is used in totally bogus ways since nobody really
seems to understand what it actually does.
This patch clarifies the pm_disk_mode description.
It also removes all the arm and sh users that think they can veto suspend to
disk via pm_ops; not so since the user can always do echo shutdown >
/sys/power/disk, they need to find a better way involving Kconfig or such.
ACPI is the only user left with a non-zero pm_disk_mode.
The patch also sets the default mode to shutdown again, but when a new pm_ops
is registered its pm_disk_mode is selected as default, that way the default
stays for ACPI where it is apparently required.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: <linux-pm@lists.linux-foundation.org>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Today's print_symbol function dumps a kernel symbol with printk. This
patch extends the functionality of kallsyms.c so that the symbol lookup
function may be used without the printk. This is useful for modules that
want to dump symbols elsewhere, for example, to debugfs. I intend to use
the new function call in the GFS2 file system (which will be a separate
patch).
[akpm@linux-foundation.org: build fix]
[clameter@sgi.com: sprint_symbol should return length of string like sprintf]
Signed-off-by: Robert Peterson <rpeterso@redhat.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Paulo Marques <pmarques@grupopie.com>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jikos/hid: (21 commits)
USB HID: don't warn on idVendor == 0
USB HID: add 'quirks' module parameter
USB HID: add support for dynamically-created quirks
USB HID: clarify static quirk handling as squirks
USB HID: encapsulate quirk handling into hid-quirks.c
USB HID: EMS USBII device needs HID_QUIRK_MULTI_INPUT
HID: update copyright and authorship macro
HID: introduce proper zeroing of unused bits in output reports
USB HID: add support for WiseGroup MP-8800 Quad Joypad
USB HID: add FF support for Logitech Force 3D Pro Joystick
USB HID: numlock quirk for dell W7658 keyboard
USB HID: Logitech MX3000 keyboard needs report descriptor quirk
USB HID: extend quirk for Logitech S510 keyboard
USB HID: usbkbd/usbmouse - handle errors when registering devices
USB HID: add QUIRK_HIDDEV for Belkin Flip KVM
HID: enable dead keys on a belkin wireless keyboard
USB HID: Thustmaster firestorm dual power v1 support
USB HID: specify explicit size for hid_blacklist.quirks
USB HID: fix retry & reset logic
USB HID: consolidate vendor/product ids
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[IPV4] SNMP: Support OutMcastPkts and OutBcastPkts
[IPV4] SNMP: Support InMcastPkts and InBcastPkts
[IPV4] SNMP: Support InTruncatedPkts
[IPV4] SNMP: Support InNoRoutes
[SNMP]: Add definitions for {In,Out}BcastPkts
[TCP] FRTO: RFC4138 allows Nagle override when new data must be sent
[TCP] FRTO: Delay skb available check until it's mandatory
[XFRM]: Restrict upper layer information by bundle.
[TCP]: Catch skb with S+L bugs earlier
[PATCH] INET : IPV4 UDP lookups converted to a 2 pass algo
[L2TP]: Add the ability to autoload a pppox protocol module.
[SKB]: Introduce skb_queue_walk_safe()
[AF_IUCV/IUCV]: smp_call_function deadlock
[IPV6]: Fix slab corruption running ip6sic
[TCP]: Update references in two old comments
[XFRM]: Export SPD info
[IPV6]: Track device renames in snmp6.
[SCTP]: Fix sctp_getsockopt_local_addrs_old() to use local storage.
[NET]: Remove NETIF_F_INTERNAL_STATS, default to internal stats.
[NETPOLL]: Remove CONFIG_NETPOLL_RX
...
* 'for-linus' of git://git.kernel.dk/data/git/linux-2.6-block:
[PATCH] elevator: elv_list_lock does not need irq disabling
[BLOCK] Don't pin lots of memory in mempools
cfq-iosched: speedup cic rb lookup
ll_rw_blk: add io_context private pointer
cfq-iosched: get rid of cfqq hash
cfq-iosched: tighten queue request overlap condition
cfq-iosched: improve sync vs async workloads
cfq-iosched: never allow an async queue idling
cfq-iosched: get rid of ->dispatch_slice
cfq-iosched: don't pass unused preemption variable around
cfq-iosched: get rid of ->cur_rr and ->cfq_list
cfq-iosched: slice offset should take ioprio into account
[PATCH] cfq-iosched: style cleanups and comments
cfq-iosched: sort IDLE queues into the rbtree
cfq-iosched: sort RT queues into the rbtree
[PATCH] cfq-iosched: speed up rbtree handling
cfq-iosched: rework the whole round-robin list concept
cfq-iosched: minor updates
cfq-iosched: development update
cfq-iosched: improve preemption for cooperating tasks
PCI devices were being programmed with an incorrect base address value.
This patch moves I/O space into a 16-bit addressable region and corrects
the i/o offset.
Much thanks to Martin Michlmayr for tracking this issue and testing
debug patches.
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The updated IP-MIB RFC (RFC4293) specifys new objects, InBcastPkts
and OutBcastPkts. This adds definitions for them.
Signed-off-by: Mitsuru Chinen <mitch@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a corner case where less than MSS sized new data thingie
is awaiting in the send queue. For F-RTO to work correctly, a
new data segment must be sent at certain point or F-RTO cannot
be used at all. RFC4138 allows overriding of Nagle at that
point.
Implementation uses frto_counter states 2 and 3 to distinguish
when Nagle override is needed.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
On MIPv6 usage, XFRM sub policy is enabled.
When main (IPsec) and sub (MIPv6) policy selectors have the same
address set but different upper layer information (i.e. protocol
number and its ports or type/code), multiple bundle should be created.
However, currently we have issue to use the same bundle created for
the first time with all flows covered by the case.
It is useful for the bundle to have the upper layer information
to be restructured correctly if it does not match with the flow.
1. Bundle was created by two policies
Selector from another policy is added to xfrm_dst.
If the flow does not match the selector, it goes to slow path to
restructure new bundle by single policy.
2. Bundle was created by one policy
Flow cache is added to xfrm_dst as originated one. If the flow does
not match the cache, it goes to slow path to try searching another
policy.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
SACKED_ACKED and LOST are mutually exclusive with SACK, thus
having their sum larger than packets_out is bug with SACK.
Eventually these bugs trigger traps in the tcp_clean_rtx_queue
with SACK but it's much more informative to do this here.
Non-SACK TCP, however, could get more than packets_out duplicate
ACKs which each increment sacked_out, so it makes sense to do
this kind of limitting for non-SACK TCP but not for SACK enabled
one. Perhaps the author had the opposite in mind but did the
logic accidently wrong way around? Anyway, the sacked_out
incrementer code for non-SACK already deals this issue before
calling sync_left_out so this trapping can be done
unconditionally.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we scale the mempool sizes depending on memory installed
in the machine, except for the bio pool itself which sits at a fixed
256 entry pre-allocation.
There's really no point in "optimizing" this OOM path, we just need
enough preallocated to make progress. A single unit is enough, lets
scale it down to 2 just to be on the safe side.
This patch saves ~150kb of pinned kernel memory on a 32-bit box.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch provides a method for walking skb lists while inserting or
removing skbs from the list.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
input-polldev provides a skeleton for supporting simple input
devices that need to be periodically scanned or polled to
detect changes in their state.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch puts enable_kernel_spe into <asm-powerpc/system.h> along with
enable_kernel_altivec etc.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The arch/ppc/syslib/ppc_sys.c infrastructure does not work well for the
virtex ports. Move the ml300 and ml403 board ports over to use the new
virtex_devices infrastructure.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The header files for the ml403 and ml300 are virtually identical, merge
them into a single file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (107 commits)
smc911x: fix compilation breakage wjen debug is on
[netdrvr] eexpress: minor corrections
add NAPI support to sb1250-mac.c
ixgb: ROUND_UP macro cleanup in drivers/net/ixgb
e1000: ROUND_UP macro cleanup in drivers/net/e1000
Generic HDLC sparse annotations
e100: Optionally use I/O mode only to access register space
e100: allow bad MAC address when running with invalid eeprom csum
ehea: fix for dlpar support
ehea: fix for sysfs entries
3C509: Remove unnecessary include of <linux/pm_legacy.h>
NetXen: Fix for vmalloc issues
NetXen: Fixes for Power PC architecture
NetXen: Port swap feature for multi port cards
NetXen: Removal of redundant macros
NetXen: Multi PCI support for Quad cards
NetXen: Removal of redundant argument passing
NetXen: Use multiple PCI functions
[netdrvr e100] experiment with doing RX in a similar manner to eepro100
[PATCH] ieee80211: add missing global needed by IEEE80211_DEBUG_XXXX
...
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev: (86 commits)
SPIN_LOCK_UNLOCKED cleanup in drivers/ata/pata_winbond.c
drivers/ata/pata_cmd640.c: fix build with CONFIG_PM=n
pata_hpt37x: Further small fixes
pata_hpt3x2n: Add HPT371N support and other bits
ata: printk warning fixes
libata: separate ATA_EHI_DID_RESET into DID_SOFTRESET and DID_HARDRESET
ahci: consolidate common port flags
ata_timing: ensure t->cycle is always correct
libata: add missing call to ->cable_detect() in new EH path
pata_amd: remove contamination added during cable_detect conversion
libata: Handle drives that require a spin-up command before first access
libata: HPA support
libata: kill probe_ent and related helpers
libata: convert the remaining PATA drivers to new init model
libata: convert the remaining SATA drivers to new init model
libata: convert ata_pci_init_native_mode() users to new init model
libata: convert drivers with combined SATA/PATA ports to new init model
libata: add init helpers including ata_pci_prepare_native_host()
libata: convert native PCI host handling to new init model
libata: convert legacy PCI host handling to new init model
...
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (105 commits)
sonypi: use mutex instead of semaphore
sony-laptop: remove user visible camera controls as platform attributes
meye: make meye use sony-laptop instead of sonypi
sony-laptop: add a meye-usable include file for camera ops
sony-laptop: complete the motion eye camera support in sony-laptop
sonypi: try to detect if sony-laptop has already taken one of the known ioports
sonypi: suggest sonypi users to try sony-laptop instead
sony-laptop: add edge modem support (also called WWAN)
sony-laptop: add locking on accesses to the ioport and global vars
sony-laptop: add camera enable/disable parameter, better handle possible infinite loop
thinkpad-acpi: make drivers/misc/thinkpad_acpi:fan_mutex static
ACPI: thinkpad-acpi: add sysfs support to wan and bluetooth subdrivers
ACPI: thinkpad-acpi: add sysfs support to hotkey subdriver
ACPI: thinkpad-acpi: improve dock subdriver initialization
ACPI: thinkpad-acpi: improve debugging for acpi helpers
ACPI: thinkpad-acpi: improve fan control documentation
ACPI: thinkpad-acpi: map ENXIO to EINVAL for fan sysfs
ACPI: thinkpad-acpi: fix a fan watchdog invocation
ACPI: thinkpad-acpi: do not arm fan watchdog if it would not work
ACPI: thinkpad-acpi: add a fan-control feature master toggle
...
Calling smp_call_function can lead to a deadlock if it is called
from tasklet context.
Fixing this deadlock requires to move the smp_call_function from the
tasklet context to a work queue. To do that queue the path pending
interrupts to a separate list and move the path cleanup out of
iucv_path_sever to iucv_path_connect and iucv_path_pending.
This creates a new requirement for iucv_path_connect: it may not be
called from tasklet context anymore.
Also fixed compile problem for CONFIG_HOTPLUG_CPU=n and
another one when walking the cpu_online mask. When doing this,
we must disable cpu hotplug.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch you can use iproute2 in user space to efficiently see
how many policies exist in different directions.
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
Herbert Xu conviced me that a new flag was overkill; every driver
currently overrides get_stats, so we might as well make the internal
one the default. If someone did fail to set get_stats, they would now
get all 0 stats instead of "No statistics available".
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_NETPOLL_TRAP causes the TX queue controls to be completely bypassed in
the netpoll's "trapped" mode which easily causes overflows in the drivers with
short TX queues (most notably, in 8139too with its 4-deep queue). So, make
this option more sensible by making it only bypass the TX softirq wakeup.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Acked-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Copy and rename (for easier co-existence) the MEYE-wise exported interface.
Signed-off-by: Mattia Dongili <malattia@linux.it>
Signed-off-by: Len Brown <len.brown@intel.com>
Separate ATA_EHI_DID_RESET into ATA_EHI_DID_SOFTRESET and
ATA_EHI_DID_HARDRESET. ATA_EHI_DID_RESET is redefined as OR of the
two flags. This patch doesn't introduce any behavior change. This
will be used later to determine whether _SDD is necessary or not.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(S)ATA drives can be configured for "power-up in standby",
a mode whereby a specific "spin up now!" command is required
before the first media access.
Currently, a drive with this feature enabled can not be used at all
with libata, and once in this mode, the drive becomes a doorstop.
The older drivers/ide subsystem at least enumerates the drive,
so that it can be woken up after the fact from a userspace HDIO_*
command, but not libata.
This patch adds support to libata for the "power-up in standby"
mode where a "spin up now!" command (SET_FEATURES) is needed.
With this, libata will recognize such drives, spin them up,
and then re-IDENTIFY them if necessary to get a full/complete
set of drive features data.
Drives in this state are determined by looking for
special values in id[2], as documented in the current ATA specs.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Add support for ignoring the BIOS HPA result (off by default) and setting
the disk to the full available size unless already frozen.
Tested with various platforms/disks and confirmed to work with the
Macintosh (which broke earlier) and ata_piix (breakage due to the LBA48
readback that Tejun fixed).
For normal users this brings us, I believe, to feature parity with old IDE
(and of course more featured in some areas too).
Signed-off-by: Jeff Garzik <jeff@garzik.org>
All drivers are converted to new init model. Kill probe_ent,
ata_device_add() and ata_pci_init_native_mode().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
These will be used to convert LLDs to new init model.
* Add irq_handler field to port_info. In new init model, requesting
IRQ is LLD's responsibility and libata doesn't need to know about
irq_handler. Most LLDs can simply register their irq_handler but
some need different irq_handler depending on specific chip. The
added port_info->irq_handler field can be used by LLDs to select
the matching IRQ handler in such cases.
* Add ata_dummy_port_info.
* Implement ata_pci_prepare_native_host(), a helper to alloc ATA host,
acquire all resources and init the host in one go.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert native PCI host handling to alloc-init-register model. New
function ata_pci_init_native_host() follows the new init model and
replaces ata_pci_init_native_mode(). As there are remaining LLD
users, the old function isn't removed yet.
ata_pci_init_one() is reimplemented using the new function and now
fully converted to new init model.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ata_host_alloc_pinfo() and ata_host_register(). These helpers
will be used in the following patches to adopt new init model.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reorganize ata_host_alloc() and its subroutines into the following
three functions.
* ata_host_alloc() : allocates host and its ports. shost is not
registered automatically.
* ata_scsi_add_hosts() : allocates and adds shosts associated with an
ATA host. Used by ata_host_register().
* ata_host_register() : takes a fully initialized ata_host structure
and registers it to libata layer and probes it.
Only ata_host_alloc() and ata_host_register() are exported.
ata_device_add() is rewritten using the above functions. This patch
does not introduce any observable behavior change. Things worth
mentioning.
* print_id is assigned at registration time and LLDs are allowed to
overallocate ports and reduce host->n_ports during initialization.
ata_host_register() will throw away unused ports automatically.
* All SCSI host initialization stuff now resides in
ata_scsi_add_hosts() in libata-scsi.c, where it should be.
* ipr is now the only user of ata_host_init(). Either kill it by
converting ipr to use ata_host_alloc() and friends or rename and
move it to libata-scsi.c
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_host_start() from ata_device_add(). ata_host_start()
calls ->port_start on each port if available and freezes the port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't embed ap inside shost. Allocate it separately and point it back
from shosts's hostdata. This makes port allocation more flexible and
allows regular ATA and SAS share host alloc/init paths.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SB600 RAID and SB600 SATA is the same controller and share the
same PCI ID 0x4380. There is no such PCI ID 0x4381.
Signed-off-by: Conke Hu <conke.hu@gmail.com>
---------
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The READ/WRITE LONG commands are theoretically obsolete,
but the majority of drives in existance still implement them.
The WRITE_LONG and WRITE_LONG_ONCE commands are of particular
interest for fault injection testing -- eg. creating "media errors"
at specific locations on a disk.
The fussy bit is that these commands require a non-standard
sector size, usually 520 bytes instead of 512.
This patch adds support to libata for READ/WRITE LONG commands
issued via SG_IO/ATA_16.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Both old-IDE and libata should be able handle all controllers and
devices found using normal resource reservation methods.
This eliminates the awful, low-performing split-driver configuration
where old-IDE drove the PATA portion of a PCI device, in PIO-only mode,
and libata drove the SATA portion of the /same/ PCI device, in DMA mode.
Typically vendors would ship SATA hard drive / PATA optical
configuration, which would lend itself to slow (PIO-only) CD-ROM
performance.
For Intel users running in combined mode, it is now wholly dependent on
your driver choice (potentially link order, if you compile both drivers
in) whether old-IDE or libata will drive your hardware.
In either case, you will get full performance from both SATA and PATA
ports now, without having to pass a kernel command line parameter.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With Tejun having added adev->ap some time ago we can get rid of the
almost unused port being passed to mode filters. And while we are
doing filters, lets turn on the !IORDY filter as well.
Signed-off-by: Alan Cox <alan@redhat.com>
With some hand massaging from
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This splits set_mode into do_set_mode and the wrapper so that a driver can
call the standard method inside its own. This in theory also obsoletes
->post_set_mode().
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement pcim_iounmap_regions() - the opposite of
pcim_iomap_regions().
Signed-off-by: Tejun heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2.6.21-rc has horrible problems with libata and PATA cable types (and
thus speeds). This occurs because Tejun fixed a pile of other bugs and
we now do cable detect enforcement for drive side detection properly.
Unfortunately we don't do the process around cable detection right. Tejun
identified the problem and pointed to the right Annex in the spec, this patch
implements the rest of the needed changes.
We add a ->cable_detect() method called after the identify
sequence which allows a host to do host side detection at this point
should it wish, or to modify the results of the drive side identify.
This separate ->cable_detect method also cleans up a lot of code because
many drivers have their own error_handler methods which really just set
the cable type.
If there is no ->cable_detect method the cable type is left alone so a
driver setting it earlier (eg because it has the SATA flags set or
because it uses the old error_handler approach) will still do the right
thing (or at least the same thing) as before.
This patch simply adds the cable_detect method and helpers it doesn't use
them but other follow up patches will (ie Adrian please don't submit
patches to unexport them ;))
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It used to be impossible to get from ata_device to ata_port but that is
no longer true. Various methods have been cleaned up over time but
dev_config still takes both and most users don't need both anyway. Tidy
this one up
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add definition for S3C2410_UDC_FUNCADDR_UDPATE
register definition for UDC driver.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Transmit on Demand: Fix spelling in config option, and make it actually enable TOD.
Signed-off-by: Michael Reiss <michael.f.reiss@freescale.com>
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
migrate ucc_geth to use the common phylib code.
There are several side effects from doing this:
o deprecate 'interface' property specification present
in some old device tree source files in
favour of a split 'max-speed' and 'interface-type'
description to appropriately match definitions
in include/linux/phy.h. Note that 'interface' property
is still honoured if max-speed or interface-type
are not present (backward compatible).
o compile-time CONFIG_UGETH_HAS_GIGA is eliminated
in favour of probe time speed derivation logic.
o adjust_link streamlined to only operate on maccfg2
and upsmr.r10m, instead of reapplying static initial
values related to the interface-type.
o Addition of UEC MDIO of_platform driver requires
platform code add 'mdio' type to id list
prior to calling of_platform_bus_probe (separate patch).
o ucc_struct_init introduced to reduce ucc_geth_startup
complexity.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The RGMII spec allows compliance for devices that implement an internal
delay on TXC or RXC inside the transmitter. This patch adds an RGMII_ID
definition to support RGMII-ID devices in the phylib.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
IEEE80211_RADIOTAP_FCS is obsolete and should not be used. It's no
longer defined. Remove it from the comment too.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After 13 years of use, it looks like my email address is finally going
to disappear. While this is likely to drop the amount of incoming spam
greatly ;-), it may also affect more appropriate messages, so let's
update my email address in various places. In addition, Host AP mailing
list is subscribers-only and linux-wireless can also be used for
discussing issues related to this driver which is now shown in
MAINTAINERS.
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Document that all fields must be little endian. Use annotated types
even in the comments. Consistently use shorter type names (u8, s8).
Realign the comments.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current tc35815 driver is very obsolete and less maintained for a long
time. Replace it with a new driver based on one from CELF patch
archive.
Major advantages of CELF version (version 1.23, for kernel 2.6.10) are:
* Independent of JMR3927.
(Actually independent of MIPS, but AFAIK the chip is used only on
MIPS platforms)
* TX4938 support.
* 64-bit proof.
* Asynchronous and on-demand auto negotiation.
* High performance on non-coherent architecture.
* ethtool support.
* Many bugfixes and cleanups.
And improvoments since version 1.23 are:
* TX4939 support.
* NETPOLL support.
* NAPI support. (disabled by default)
* Reduce memcpy on receiving.
* PM support.
* Many cleanups and bugfixes.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the Marvell Libertas 8388 802.11 USB driver.
Signed-off-by: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.infradead.org/mtd-2.6: (46 commits)
[MTD] [MAPS] drivers/mtd/maps/ck804xrom.c: convert pci_module_init()
[MTD] [NAND] CM-x270 MTD driver
[MTD] [NAND] Wrong calculation of page number in nand_block_bad()
[MTD] [MAPS] fix plat-ram printk format
[JFFS2] Fix compr_rubin.c build after include file elimination.
[JFFS2] Handle inodes with only a single metadata node with non-zero isize
[JFFS2] Tidy up licensing/copyright boilerplate.
[MTD] [OneNAND] Exit loop only when column start with 0
[MTD] [OneNAND] Fix access the past of the real oobfree array
[MTD] [OneNAND] Update Samsung OneNAND official URL
[JFFS2] Better fix for all-zero node headers
[JFFS2] Improve read_inode memory usage, v2.
[JFFS2] Improve failure mode if inode checking leaves unchecked space.
[JFFS2] Fix cross-endian build.
[MTD] Finish conversion mtd_blkdevs to use the kthread API
[JFFS2] Obsolete dirent nodes immediately on unlink, where possible.
Use menuconfig objects: MTD
[MTD] mtd_blkdevs: Convert to use the kthread API
[MTD] Fix fwh_lock locking
[JFFS2] Speed up mount for directly-mapped NOR flash
...
Fix miscellaneous networking compilation errors.
(*) Export ktime_add_ns() for modules.
(*) wext_proc_init() should have an ANSI declaration.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (78 commits)
USB: update MAINAINERS and CREDITS for Freescale USB driver
USB: update gadget files for fsl_usb2_udc driver
USB: add Freescale high-speed USB SOC device controller driver
USB: quirk for broken suspend of IT8152F/G
USB: iowarrior.c: timeouts too small in usb_control_msg calls
USB: dell device id for option.c
USB: Remove Huawei unusual_devs entry
USB: CP2101 New Device IDs
USB: add picdem device to ldusb
usbfs micro optimitation
USB: remove ancient/broken CRIS hcd
usb ethernet gadget, workaround network stack API glitch
USB: add "busnum" attribute for USB devices
USB: cxacru: ADSL state management
usbatm: Detect usb device shutdown and ignore failed urbs
USB: Remove duplicate define of OHCI_QUIRK_ZFMICRO
USB: BandRich BandLuxe HSDPA Data Card Driver
USB gadget rndis: fix struct rndis_packet_msg_type unaligned bug
USB Elan FTDI: check for driver registration status
USB: sierra: add more checks on shutdown
...
* 'master' of ssh://master.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (184 commits)
V4L/DVB (5563): Radio-maestro.c Replace radio_ioctl to use video_ioctl2
V4L/DVB (5562): Radio-gemtek-pci.c Replace gemtek_pci_ioctl to use video_ioctl2
V4L/DVB (5560): Ivtv: fix incorrect bitwise-and for command flags.
V4L/DVB (5558): Opera: use 7-bit i2c addresses
V4L/DVB (5557): Cafe_ccic: check return value of pci_enable_device
V4L/DVB (5556): Radio-gemtek.c Replace gemtek_ioctl to use video_ioctl2
V4L/DVB (5555): Radio-aimslab.c Replace rt_ioctl to use video_ioctl2
V4L/DVB (5554): Fix: vidioc_g_parm were not zeroing the memory
V4L/DVB (5553): Replace typhoon_do_ioctl to use video_ioctl2
V4L/DVB (5552): Plan-b: Switch to refcounting PCI API
V4L/DVB (5551): Plan-b: header change
V4L/DVB (5550): Radio-sf16fmi.c Replace fmi_do_ioctl to use video_ioctl2
V4L/DVB (5549): Radio-sf16fmr2.c Replace fmr2_do_ioctl to use video_ioctl2
V4L/DVB (5548): Fix v4l2 buffer to the length
V4L/DVB (5547): Add ENUM_FRAMESIZES and ENUM_FRAMEINTERVALS ioctls
V4L/DVB (5546): Radio-terratec.c Replace tt_do_ioctl to use video_ioctl2
V4L/DVB (5545): Saa7146: Release capture buffers on device close
V4L/DVB (5544): Budget-av: Make inversion setting configurable, add KNC ONE V1.0 card
V4L/DVB (5543): Tda10023: Add support for frontend TDA10023
V4L/DVB (5542): Budget-av: Remove polarity switching of the clock for DVB-C
...
Minor doc update to <linux/usb/ch9.h> ... say where USB_DT_CS_* came
from and update the definitions to match how they're derived there.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as877) adds a "last_busy" field to struct usb_device, for
use by the autosuspend framework. Now if an autosuspend call comes at
a time when the device isn't busy but hasn't yet been idle for long
enough, the timer can be set to exactly the desired value. And we
will be ready to handle things like HID drivers, which can't maintain
a useful usage count and must rely on the time-of-last-use to decide
when to autosuspend.
The patch also makes some related minor improvements:
Move the calls to the autosuspend condition-checking routine
into usb_suspend_both(), which is the only place where it
really matters.
If the autosuspend timer is already running, don't stop
and restart it.
Replace immediate returns with gotos so that the optional
debugging ouput won't be bypassed.
If autoresume is disabled but the device is already awake,
don't return an error for an autoresume call.
Don't try to autoresume a device if it isn't suspended.
(Yes, this undercuts the previous change -- so sue me.)
Don't duplicate existing code in the autosuspend work routine.
Fix the kerneldoc in usb_autopm_put_interface(): If an
autoresume call fails, the usage counter is left unchanged.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
o The "real" usb-devices export now a device node which can
populate /dev/bus/usb.
o The usb_device class is optional now and can be disabled in the
kernel config. Major/minor of the "real" devices and class devices
are the same.
o The environment of the usb-device event contains DEVNUM and BUSNUM to
help udev and get rid of the ugly udev rule we need for the class
devices.
o The usb-devices and usb-interfaces share the same bus, so I used
the new "struct device_type" to let these devices identify
themselves. This also removes the current logic of using a magic
platform-pointer.
The name of the device_type is also added to the environment
which makes it easier to distinguish the different kinds of devices
on the same subsystem.
It looks like this:
add@/devices/pci0000:00/0000:00:1d.1/usb2/2-1
ACTION=add
DEVPATH=/devices/pci0000:00/0000:00:1d.1/usb2/2-1
SUBSYSTEM=usb
SEQNUM=1533
MAJOR=189
MINOR=131
DEVTYPE=usb_device
PRODUCT=46d/c03e/2000
TYPE=0/0/0
BUSNUM=002
DEVNUM=004
This udev rule works as a replacement for usb_device class devices:
SUBSYSTEM=="usb", ACTION=="add", ENV{DEVTYPE}=="usb_device", \
NAME="bus/usb/$env{BUSNUM}/$env{DEVNUM}", MODE="0644"
Updated patch, which needs the device_type patches in Greg's tree.
I also got a bugzilla assigned for this. :)
https://bugzilla.novell.com/show_bug.cgi?id=250659
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as874) adds another piece to the user-visible part of the
USB autosuspend interface. The new power/level sysfs attribute allows
users to force the device on (with autosuspend off), force the device
to sleep (with autoresume off), or return to normal automatic operation.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as867) adds an entry for the new power/autosuspend
attribute in Documentation/ABI/testing, and it changes the behavior of
the delay value. Now a delay of 0 means to autosuspend as soon as
possible, and negative values will prevent autosuspend.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this adds another structure for CDC devices to cdc.h.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (46 commits)
dev_dbg: check dev_dbg() arguments
drivers/base/attribute_container.c: use mutex instead of binary semaphore
mod_sysfs_setup() doesn't return errno when kobject_add_dir() failure occurs
s2ram: add arch irq disable/enable hooks
define platform wakeup hook, use in pci_enable_wake()
security: prevent permission checking of file removal via sysfs_remove_group()
device_schedule_callback() needs a module reference
s390: cio: Delay uevents for subchannels
sysfs: bin.c printk fix
Driver core: use mutex instead of semaphore in DMA pool handler
driver core: bus_add_driver should return an error if no bus
debugfs: Add debugfs_create_u64()
the overdue removal of the mount/umount uevents
kobject: Comment and warning fixes to kobject.c
Driver core: warn when userspace writes to the uevent file in a non-supported way
Driver core: make uevent-environment available in uevent-file
kobject core: remove rwsem from struct subsystem
qeth: Remove usage of subsys.rwsem
PHY: remove rwsem use from phy core
IEEE1394: remove rwsem use from ieee1394 core
...
Negative speed values have to be allowed for reverse playback.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDEO_EVENT_VSYNC needs to tell the application which field it was that
received a VSYNC (odd/even/progressive). The vsync_field was added to the
union in video_event for this purpose.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It took three core maintainers, over four years of work, eight new i2c
modules, eleven new V4L2 ioctls, three new DVB video ioctls, a Sliced
VBI API, a new MPEG encoder API, an enhanced DVB video MPEG decoding
API, major YUV/OSD contributions from Ian and John, web/wiki/svn/trac
support from Axel Thimm, (hardware) support from Hauppauge, support and
assistance from the v4l-dvb people and the many, many users of ivtv to
finally make it possible to merge this driver into the kernel.
Thank you all!
Signed-off-by: Kevin Thayer <nufan_wfk@yahoo.com>
Signed-off-by: Chris Kennedy <c@groovy.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: John P Harvey <john.p.harvey@btinternet.com>
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The documentation of Several miscellaneous commands was updated.
As a result of which the CX2341X_ENC_UNKNOWN command was renamed to
CX2341X_ENC_SET_VERT_CROP_LINE.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This change supplies a more generic version of the tuner callback.
The tuner struct now has a function pointer
int (*tuner_callback) (void *dev, int command, int arg)
additionally to a int config parameter.
both can be set through the TUNER_SET_TYPE_ADDR client call.
Note that the meaning of the parameters depend on the tuner type.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These entries mainly are to support configurations of the tda827x
silicon tuner with a preamplifier.
The values can be set throgh the attach inform or through
the extended TUNER_SET_TYPE_ADDR client call. The function pointer
will only be updated if the parameter is not NULL.
Since a typecast is necessary to set the pointer, i added a typedef for
this pointer (tuner_gpio_func_t) in tuner.h
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx23415 adds some extra features that this DVB decoding API did
not support. This API has been expanded to support the required
features. Both source and binary backwards compatibility is kept
intact by these changes. So existing applications are not affected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VIDIOC_G_CHIP_IDENT improves debugging of card problems: it can be
used to detect which chips are on the board and based on that information
selected register dumps can be made, making it easy to debug complicated
media chips containing tens or hundreds of registers.
This ioctl replaces the internal VIDIOC_INT_G_CHIP_IDENT ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added VIDIOC_INT_G_STD_OUTPUT and VIDIOC_INT_S_STD_OUTPUT to allow drivers
to set the TV standard for video output separately from the video capture.
This is needed for cx23415 support where the decoder is separate from the
encoder and can have a different TV standard.
Modified the saa7127 module to listen to VIDIOC_INT_G/S_STD_OUTPUT instead
of VIDIOC_G/S_STD.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add V4L2_BUF_TYPE_VIDEO_OUTPUT_OVERLAY support.
Also add support for local and global alpha overlays.
Add new field enums V4L2_FIELD_INTERLACED_TB and V4L2_FIELD_INTERLACED_BT.
These changes are needed to support the ivtv On Screen Display features.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add V4L2_CAP_VIDEO_OUTPUT_POS capability and x, y position coordinates
to struct v4l2_pix_format.
This is needed to support positioning the MPEG/YUV output of the cx23415.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Added V4L2_CID_MPEG_AUDIO_MUTE, V4L2_CID_MPEG_VIDEO_MUTE and
V4L2_CID_MPEG_CX2341X_STREAM_INSERT_NAV_PACKETS controls together with
their implementation in the cx2341x module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Duplicate what Zach Brown did for pr_debug in commit
8b2a1fd1b3
[akpm@linux-foundation.org: fix a couple of things which broke]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After some more discussion this patch replaces it:
From: Johannes Berg <johannes@sipsolutions.net>
Subject: suspend: add arch irq disable/enable hooks
For powermac, we need to do some things between suspending devices and
device_power_off, for example setting the decrementer. This patch
allows architectures to define arch_s2ram_{en,dis}able_irqs in their
asm/suspend.h to have control over this step.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This defines a platform hook to enable/disable a device as a wakeup event
source. It's initially for use with ACPI, but more generally it could be used
whenever enable_irq_wake()/disable_irq_wake() don't suffice.
The hook is called -- if available -- inside pci_enable_wake(); and the
semantics of that call are enhanced so that support for PCI PME# is no longer
needed. It can now work for devices with "legacy PCI PM", when platform
support allows it. (That support would use some board-specific signal for for
the same purpose as PME#.)
[akpm@linux-foundation.org: Make it compile with CONFIG_PM=n]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prevent permission checking from being performed when the kernel wants to
unconditionally remove a sysfs group, by introducing an kernel-only variant
of lookup_one_len(), lookup_one_len_kern().
Additionally, as sysfs_remove_group() does not check the return value of
the lookup before using it, a BUG_ON has been added to pinpoint the cause
of any problems potentially caused by this (and as a form of annotation).
Signed-off-by: James Morris <jmorris@namei.org>
Cc: Nagendra Singh Tomar <nagendra_tomar@adaptec.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Eric Paris <eparis@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as896b) fixes an oversight in the design of
device_schedule_callback(). It is necessary to acquire a reference to the
module owning the callback routine, to prevent the module from being
unloaded before the callback can run.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Satyam Sharma <satyam.sharma@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I went to use this the other day, only to find it didn't exist.
It's a straight copy of the debugfs u32 code, then s/u32/u64/. A quick
test shows it seems to be working.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch contains the overdue removal of the mount/umount uevents.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It isn't used at all by the driver core anymore, and the few usages of
it within the kernel have now all been fixed as most of them were using
it incorrectly. So remove it.
Now the whole struct subsys can be removed from the system, but that's
for a later patch...
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver core: add suspend() and resume() to struct device_type
In cases when there are devices of different types in the same class
we can't use class's implementation of suspend and resume methods and
we need to add them to struct device_type instead.
Also fix error handling in resume code (we should not try to call
class's resume method iof bus's resume method for the device failed.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The completion in the driver release path is due to ancient history in
the _very_ early 2.5 days when we were not tracking the module reference
count of attributes. It is not needed at all and can be removed.
Note, we now have an empty release function for the driver structure.
This is due to the fact that drivers are statically allocated in the
system at this point in time, something which I want to change in the
future. But remember, drivers are really code, which is reference
counted by the module, unlike devices, which are data and _must_ be
reference counted properly in order to work correctly.
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make multithreaded probing work per subsystem instead of per driver.
It doesn't make much sense to probe the same device for multiple drivers in
parallel (after all, only one driver can bind to the device). Instead, create
a probing thread for each device that probes the drivers one after another.
Also make the decision to use multi-threaded probe per bus instead of per
device and adapt the pci code.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If "name" of a device_type is specified, the uevent will
contain the device_type name in the DEVTYPE variable.
This helps userspace to distingiush between different types
of devices, belonging to the same subsystem.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Driver core: use attribute groups in struct device_type
Attribute groups are more flexible than attribute lists
(an attribute list can be represented by anonymous group)
so switch struct device_type to use them.
Also rework attribute creation for devices so that they all
cleaned up properly in case of errors.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Kay Sievers <kay.sievers@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We get two per-bus sysfs files:
ls-l /sys/subsystem/usb
drwxr-xr-x 2 root root 0 2007-02-16 16:42 devices
drwxr-xr-x 7 root root 0 2007-02-16 14:55 drivers
-rw-r--r-- 1 root root 4096 2007-02-16 16:42 drivers_autoprobe
--w------- 1 root root 4096 2007-02-16 16:42 drivers_probe
The flag "drivers_autoprobe" controls the behavior of the bus to bind
devices by default, or just initialize the device and leave it alone.
The command "drivers_probe" accepts a bus_id and the bus tries to bind a
driver to this device.
Systems who want to control the driver binding with udev, switch off the
bus initiated probing:
echo 0 > /sys/subsystem/usb/drivers_autoprobe
echo 0 > /sys/subsystem/pcmcia/drivers_autoprobe
...
and initiate the probing with udev rules like:
ACTION=="add", SUBSYSTEM=="usb", ATTR{subsystem/drivers_probe}="$kernel"
ACTION=="add", SUBSYSTEM=="pcmcia", ATTR{subsystem/drivers_probe}="$kernel"
...
Custom driver binding can happen in earlier rules by something like:
ACTION=="add", SUBSYSTEM=="usb", \
ATTRS{idVendor}=="1234", ATTRS{idProduct}=="5678" \
ATTR{subsystem/drivers/<custom-driver>/bind}="$kernel"
This is intended to solve the modprobe.conf mess with "install-rules", custom
bind/unbind-scripts and all the weird things people invented over the years.
It should also provide the functionality "libusual" was supposed to do.
With udev, one can just write a udev rule to drive all USB-disks at the
third port of USB-hub by the "ub" driver, and everything else by
usb-storage. One can also instruct udev to bind different wireless
drivers to identical cards - just selected by the pcmcia slot-number, and
whatever ...
To use the mentioned rules, it needs udev version 106, to be able to
write ATTR{}="$kernel" to sysfs files.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- uses a kset in "struct class" to keep track of all directories
belonging to this class
- merges with the /sys/devices/virtual logic.
- removes the namespace-dir if the last member of that class
leaves the directory.
There may be locking or refcounting fixes left, I stopped when it seemed
to work with network and sound modules. :)
From: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
show_state() (SysRq-T) developed the buggy habbit of not showing
TASK_RUNNING tasks. This was due to the mistaken belief that state_filter
== -1 would be a pass-through filter - while in reality it did not let
TASK_RUNNING == 0 p->state values through.
Fix this by restoring the original '!state_filter means all tasks'
special-case i had in the original version. Test-built and test-booted on
i686, SysRq-T now works as intended.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.infradead.org/ubi-2.6:
UBI: remove unused variable
UBI: add me to MAINTAINERS
JFFS2: add UBI support
UBI: Unsorted Block Images
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mfasheh/ocfs2: (27 commits)
ocfs2: Cache extent records
ocfs2: Remember rw lock level during direct io
ocfs2: Fix up i_blocks calculation to know about holes
ocfs2: Fix extent lookup to return true size of holes
ocfs2: Read from an unwritten extent returns zeros
ocfs2: make room for unwritten extents flag
ocfs2: Use own splice write actor
ocfs2: Use do_sync_mapping_range() in ocfs2_zero_tail_for_truncate()
[PATCH] Turn do_sync_file_range() into do_sync_mapping_range()
ocfs2: zero tail of sparse files on truncate
ocfs2: Teach ocfs2_get_block() about holes
ocfs2: remove ocfs2_prepare_write() and ocfs2_commit_write()
ocfs2: teach ocfs2_file_aio_write() about sparse files
ocfs2: Turn off shared writeable mmap for local files systems with holes.
ocfs2: abstract out allocation locking
ocfs2: teach extend/truncate about sparse files
ocfs2: temporarily remove extent map caching
ocfs2: sparse b-tree support
ocfs2: small cleanup of ocfs2_request_delete()
ocfs2: remove unused code
...
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6: (67 commits)
[SCSI] SUNESP: Complete driver rewrite to version 2.0
[SPARC64]: Convert PCI over to generic struct iommu/strbuf.
[SPARC]: device_node name constification fallout
[SPARC64]: Convert SBUS over to generic iommu/strbuf structs.
[SPARC64]: Add generic iommu and strbuf structs to iommu.h
[SPARC64]: Consolidate {sbus,pci}_iommu_arena.
[SPARC]: Make device_node name and type const
[SPARC64]: constify some paramaters of OF routines
[TIGON3]: of_get_property() returns const.
[SPARC64]: Fix PCI rework to adhere to of_get_property() const return.
[SPARC64]: Document and fix calculation of pages_avail.
[SPARC64]: Make sure pbm->prom_node is setup easly enough in psycho.c
[SPARC64]: Use bootmem_bootmap_pages() in choose_bootmap_pfn().
[SPARC64]: Add proper header file extern for cmdline_memory_size.
[SPARC64]: Kill sparc_ultra_dump_{i,d}tlb()
[SPARC64]: Use DECLARE_BITMAP and BITS_TO_LONGS in mm/init.c
[SPARC64]: Give move verbose show_mem() output just like i386.
[SPARC64]: Mark show_mem() printk's with KERN_INFO.
[SPARC64]: Kill kvaddr_to_phys() and friends.
[SPARC64]: Privatize sun4u_get_pte() and fix name.
...
[Robert's original log message said this was a bug but it isn't, it's
just very old fashioned syntax that is not (no longer?) documented in the
gcc documentation. So for the sake of uniformity I'm applying his
patch but with a modified log message. -- Ralf]
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is an update to the earlier patch for the sibyte headers, and superceeds
the previous patch. Changes were necessary to get the tbprof driver working
on the bcm1480.
Patch to update Sibyte header files to match master versions maintained
at Broadcom. This patch also corrects some whitespace problems, and
(hopefully) shouldn't introduce any new ones.
Signed-off-by: Mark Mason <mason@broadcom.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The page_test_and_clear_dirty primitive really consists of two
operations, page_test_dirty and the page_clear_dirty. The combination
of the two is not an atomic operation, so it makes more sense to have
two separate operations instead of one.
In addition to the improved readability of the s390 version of
SetPageUptodate, it now avoids the page_test_dirty operation which is
an insert-storage-key-extended (iske) instruction which is an expensive
operation.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Generate uevents for all cpus if cpu capability changes. This can
happen e.g. because the cpus are overheating. The cpu capability can
be read via /sys/devices/system/cpu/cpuN/capability.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
s390 machines provide hardware support for creating Linux dumps on SCSI
disks. For creating a dump a special purpose dump Linux is used. The first
32 MB of memory are saved by the hardware before the dump Linux is
booted. Via an SCLP interface, the saved memory can be accessed from
Linux. This patch exports memory and registers of the crashed Linux to
userspace via a debugfs file. For more information refer to
Documentation/s390/zfcpdump.txt, which is included in this patch.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Generic bug implementation for s390. Will increase the value of the
console output on BUG() statements since registers r0-r5,r14 will
not be clobbered by a printk() call that was previously done before
the illegal instruction of BUG() was hit.
Also implements an architecture specific WARN_ON(). Output of that
could be increased but requires common code change.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
This patch adds two improvements to the oops output. First it adds an
additional line after the PSW which decodes the different fields of it.
Second a disassembler is added that decodes the instructions surrounding
the faulting PSW. The output of a test oops now looks like this:
kernel BUG at init/main.c:419
illegal operation: 0001 [#1]
CPU: 0 Not tainted
Process swapper (pid: 0, task: 0000000000464968, ksp: 00000000004be000)
Krnl PSW : 0700000180000000 00000000000120b6 (rest_init+0x36/0x38)
R:0 T:1 IO:1 EX:1 Key:0 M:0 W:0 P:0 AS:0 CC:0 PM:0 EA:3
Krnl GPRS: 0000000000000003 00000000004ba017 0000000000000022 0000000000000001
000000000003a5f6 0000000000000000 00000000004be6a8 0000000000000000
0000000000000000 00000000004b8200 0000000000003a50 0000000000008000
0000000000516368 000000000033d008 00000000000120b2 00000000004bdee0
Krnl Code: 00000000000120a6: e3e0f0980024 stg %r14,152(%r15)
00000000000120ac: c0e500014296 brasl %r14,3a5d8
00000000000120b2: a7f40001 brc 15,120b4
>00000000000120b6: 0707 bcr 0,%r7
00000000000120b8: eb7ff0500024 stmg %r7,%r15,80(%r15)
00000000000120be: c0d000195825 larl %r13,33d108
00000000000120c4: a7f13f00 tmll %r15,16128
00000000000120c8: a7840001 brc 8,120ca
Call Trace:
([<00000000000120b2>] rest_init+0x32/0x38)
[<00000000004be614>] start_kernel+0x37c/0x410
[<0000000000012020>] _ehead+0x20/0x80
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Introduce a mutex for struct ccwgroup to prevent simuntaneous
register/unregister on the same ccwgroup device.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Add a new attribute to the channel-path sysfs directory through which
channel-path configure operations can be triggered. Also listen for
hardware events requesting channel-path configure operations and
process them accordingly.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Clean interface between cio and ipl code, so Peter stops complaining.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
gcc 4.1 doesn't seem to like const variables as inline assembly
outputs. Drop support for reading 64-bit values using get_user() so
that we can use an unsigned long to hold the result regardless of the
actual size. This should be safe since many architectures, including
i386, doesn't support reading 64-bit values with get_user().
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This int cast is superfluous since system.h cmpxchg already casts it in
(typeof(*(ptr))).
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Using readb/writeb to implement these breaks NOR flash support. I
can't see any reason why regular memcpy and memset shouldn't work.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Since the core setup code takes care of both allocation and
reservation of framebuffer memory, there's no need for this board-
specific hook anymore. Replace it with two global variables,
fbmem_start and fbmem_size, which can be used directly.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Use struct resource to specify both physical memory regions and
reserved regions and push everything into the same framework,
including kernel code/data and initrd memory. This allows us to get
rid of many special cases in the bootmem initialization and will also
make it easier to implement more robust handling of framebuffer
memory later.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Fix the I/O access macros so that they work with externally connected
devices accessed in little-endian mode over any bus width:
* Use a set of macros to define I/O port- and memory operations
borrowed from MIPS.
* Allow subarchitecture to specify address- and data-mangling
* Implement at32ap-specific port mangling (with build-time
configurable bus width. Only one bus width at a time supported
for now.)
* Rewrite iowriteN and friends to use write[bwl] and friends
(not the __raw counterparts.)
This has been tested using pata_pcmcia to access a CompactFlash card
connected to the EBI (16-bit bus width.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
