Commit Graph

60 Commits

Author SHA1 Message Date
David Brownell
a227fd7db7 USB: musb: partial DaVinci dm355 support
Partial support for DaVinci DM355, on the EVM board; peripheral
mode should work, once mainline merges DM355 support.  Missing:

  (a) renumbering the GPIO for DRVVBUS on the DM6446 EVM,
      when DAVINCI_N_GPIO increases;

  (b) disabling DM355_DEEPSLEEP.DRVVBUS_OVERRIDE so VBUS is
      driven according to the ID signal, if cpu_is_..._dm355()

The new PHY control bits are ignored on DM6446.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24 16:20:36 -07:00
Ajay Kumar Gupta
743821717c USB: musb: only turn off vbus in OTG hosts
Except on DaVinci, VBUS is now switched off as part of idling the
USB link (after a_wait_bcon) whenever a device is disconnected
from host.  This is correct for OTG hosts, where either SRP or
an ID interrupt could turn VBUS on again.

However, for non-OTG hosts there's no way to turn VBUS on again,
so the host becomes unusable.  And the procfs entry which once
allowed a manual workaround for this is now gone.

This patch adds an is_otg_enabled() check before scheduling the
switch-off timer in disconnect path, supporting a "classic host"
mode where SRP is unavailable.

[ dbrownell@users.sourceforge.net: tweak patch description ]

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24 16:20:36 -07:00
Giuseppe GORGOGLIONE
322337168f USB: musb: fix init oops crash with static FIFO config
Correct musb_read_fifosize() and musb_configure_ep0() functions
for the #ifndef BLACKFIN branch when the silicon uses static FIFO
configuration.  (Most current silicon configures this controller
to use dynamic FIFO configuration; some parts from ST don't, like
the STM STA2062.)

Signed-off-by: Giuseppe	GORGOGLIONE <giuseppe.gorgoglione@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24 16:20:36 -07:00
Ajay Kumar Gupta
1e0320f0d4 USB: musb: NAK timeout scheme on bulk RX endpoint
Fixes endpoint starvation issue when more than one bulk QH is
multiplexed on the reserved bulk RX endpoint, which is normal
for cases like serial and ethernet adapters.

This patch sets the NAK timeout interval for such QHs, and when
a timeout triggers the next QH will be scheduled.  (This resembles
the bulk scheduling done in hardware by EHCI, OHCI, and UHCI.)

This scheme doesn't work for devices which are connected to a
high to full speed tree (transaction translator) as there is
no NAK timeout interrupt from the musb controller from such
devices.

Tested with PIO, Inventra DMA, CPPI DMA.

[ dbrownell@users.sourceforge.net:  fold in start_urb() update;
  clarify only for bulk RX; don't accidentally clear WZC bits ]

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24 16:20:36 -07:00
Sergei Shtylyov
5d67a851bc USB: musb: rewrite host periodic endpoint allocation
The current MUSB host code doesn't make use of all the available
FIFOs in for periodic transfers since it wrongly assumes the RX
and TX sides of any given hw_ep always share one FIFO.

Change:  use 'in_qh' and 'out_qh' fields of the 'struct musb_hw_ep'
to check the endpoint's business; get rid of the now-unused 'periodic'
array in the 'struct musb'.  Also optimize a loop induction variable
in the endpoint lookup code.

(Based on a previous patch from Ajay Kumar Gupta <ajay.gupta@ti.com>)

[ dbrownell@users.sourceforge.net: clarify description and origin
  of this fix; whitespace ]

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24 16:20:35 -07:00
Harvey Harrison
551509d267 USB: replace uses of __constant_{endian}
The base versions handle constant folding now.

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-03-24 16:20:33 -07:00
Vikram Pandita
e747951240 USB: musb: fix srp sysfs entry deletion
The SRP sysfs attribute is dependent on gadget mode; any
gadget may support SRP.  But "rmmod musb_hdrc" didn't
remove that attribute; fix.

Signed-off-by: Vikram Pandita <vikram.pandita@ti.com>
Acked-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Anand Gadiyar
5c23c9078f USB: musb: resume suspended root hub on disconnect
If this is not done, khubd will not be informed of the disconnect
and will assume the device is still there.

Easily seen when a hub is connected with no device attached to it;
it will autosuspend.  When the hub is disconnected, it still shows
up in /proc/bus/usb/devices

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Sergei Shtylyov
136733d612 USB: musb: use right poll limit for low speed devices
Remove wrongly applied upper limit on the interrupt transfer
interval for low speed devices (not much of an error per se,
according to USB specs).

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Sergei Shtylyov
3ecdb9acf3 USB: musb: be careful with 64K+ transfer lengths, host side
Feeding 32-bit length cast down to 'u16' to min() to calculate the FIFO
count in musb_host_tx() risks sending a short packet prematurely for
transfer sizes over 64 KB.

Similarly, although data transfer size shouldn't exceed 65535 bytes for
the control endpoint, making musb_h_ep0_continue() more robust WRT URBs
with possibly oversized buffer will not hurt either...

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Sergei Shtylyov
51d9f3e100 USB: musb: fix data toggle saving with shared FIFO
For some strange reason the host side musb_giveback() decides
that it's always got an IN transfer when the hardware endpoint
is using a shared FIFO.  This causes musb_save_toggle() to read
the toggle state from the RXCSR register instead of TXCSR, and
may also cause unneeded reloading of RX endpoint registers.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Sergei Shtylyov
dc61d238b8 USB: musb: host endpoint_disable() oops fixes
The musb_h_disable() routine can oops in some cases:

 - It's not safe to read hep->hcpriv outside musb->lock,
   since it gets changed on completion IRQ paths.

 - The list iterators aren't safe to use in that way;
   just remove the first element while !list_empty(),
   so deletions on other code paths can't make trouble.

We need two "scrub the list" loops because only one branch
should touch hardware and advance the schedule.

[ dbrownell@users.sourceforge.net: massively simplify
  patch description; add key points as code comments ]

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Sergei Shtylyov
a2fd814e6a USB: musb: fix urb_dequeue() method
The urb_dequeue() method forgets to unlink 'struct musb_qh' from the
control or bulk schedules when the URB being cancelled is the only
one queued to its endpoint.  That will cause musb_advance_schedule()
to block once it reaches 'struct musb_qh' with now empty URB list, so
URBs queued for other endpoints after the one being dequeued will not
be served.

Fix by unlinking the QH from the list except when it's already being
handled (typically by musb_giveback).  Since a QH with an empty URB
list is now supposed to be freed, do that.  And remove a now-useless
check from musb_advance_schedule().

[ dbrownell@users.sourceforge.net: update patch description,
  and fold in a dequeue() comment patch ]

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Dmitry Krivoschekov
b7bdcb79de USB: musb: fix musb_host_tx() for shared endpoint FIFO
The input queue should be used for TX on endpoints which
share FIFO hardware.  The host TX path wasn't doing that.

Shared FIFOs are most often configured for periodic endpoints,
which are mostly used for RX/IN transfers ... that's probably
how this bug managed to linger for a long time.

[ dbrownell@users.sourceforge.net: update patch description ]

Signed-off-by: Dmitry Krivoschekov <dkrivoschekov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
Felipe Balbi
c2c963217b USB: musb: be careful with 64K+ transfer lengths (gadget side)
request->actual is an unsigned and we should use the same
variable type for fifo_count otherwise we might lose some
data if request->length >= 64kbytes.

[ dbrownell@users.sourceforge.net: fix compiler warning ]

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
David Brownell
34f32c9701 usb: musb: make Davinci *work* in mainline
Now that the musb build fixes for DaVinci got merged (RC3?), kick in
the other bits needed to get it finally *working* in mainline:

 - Use clk_enable()/clk_disable() ... the "always enable USB clocks"
   code this originally relied on has since been removed.

 - Initialize the USB device only after the relevant I2C GPIOs are
   available, so the host side can properly enable VBUS.

 - Tweak init sequencing to cope with mainline's relatively late init
   of the I2C system bus for power switches, transceivers, and so on.

Sanity tested on DM6664 EVM for host and peripheral modes; that system
won't boot with CONFIG_PM enabled, so OTG can't yet be tested.  Also
verified on OMAP3.

(Unrelated:  correct the MODULE_PARM_DESC spelling of musb_debug.)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-02-27 14:40:51 -08:00
David Brownell
cd67435ef9 USB: musb: Kconfig fix
The Blackfin MUSB Kconfig text didn't properly parenthesise its
dependencies.  This was visible in non-Blackfin configs by the
way the user interfaces lost track of dependencies, when doing
a bunch of test builds.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:35 -08:00
Swaminathan S
191b776616 USB: musb cppi dma fix
Initializes the actual_len field to 0 before every DMA transaction.

Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:35 -08:00
Hugo Villeneuve
704a14854a USB: musb cppi bugfixes
These compilation errors are related to incorrect
debugging macro and variable names and generated the
following errors:

  drivers/usb/musb/cppi_dma.c:437:5: warning: "MUSB_DEBUG" is not defined
  drivers/usb/musb/cppi_dma.c: In function 'cppi_next_rx_segment':
  drivers/usb/musb/cppi_dma.c:884: error: 'debug' undeclared (first use in this function)

Signed-off-by: Hugo Villeneuve <hugo@hugovil.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:35 -08:00
Julia Lawall
96bcd090fa USB: musb uses endpoint functions
This set of patches introduces calls to the following set of functions:

usb_endpoint_dir_in(epd)
usb_endpoint_dir_out(epd)
usb_endpoint_is_bulk_in(epd)
usb_endpoint_is_bulk_out(epd)
usb_endpoint_is_int_in(epd)
usb_endpoint_is_int_out(epd)
usb_endpoint_num(epd)
usb_endpoint_type(epd)
usb_endpoint_xfer_bulk(epd)
usb_endpoint_xfer_control(epd)
usb_endpoint_xfer_int(epd)
usb_endpoint_xfer_isoc(epd)

In some cases, introducing one of these functions is not possible, and it
just replaces an explicit integer value by one of the following constants:

USB_ENDPOINT_XFER_BULK
USB_ENDPOINT_XFER_CONTROL
USB_ENDPOINT_XFER_INT
USB_ENDPOINT_XFER_ISOC

An extract of the semantic patch that makes these changes is as follows:
(http://www.emn.fr/x-info/coccinelle/)

// <smpl>
@r1@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) ==
- \(USB_ENDPOINT_XFER_CONTROL\|0\))
+ usb_endpoint_xfer_control(epd)

@r5@ struct usb_endpoint_descriptor *epd; @@

- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) ==
-  \(USB_DIR_IN\|0x80\))
+ usb_endpoint_dir_in(epd)

@inc@
@@

#include <linux/usb.h>

@depends on !inc && (r1||r5)@
@@

+ #include <linux/usb.h>
  #include <linux/usb/...>
// </smpl>

Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:34 -08:00
Kalle Valo
af7e0c5f12 USB: musb: tusb6010 buildfix
drivers/usb/musb/tusb6010_omap.c:18:26: error: asm/arch/dma.h:
  No such file or directory
drivers/usb/musb/tusb6010_omap.c:19:26: error: asm/arch/mux.h:
  No such file or directory

Signed-off-by: Kalle Valo <kalle.valo@nokia.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:33 -08:00
Ajay Kumar Gupta
97a3989681 USB: musb free_irq bugfix
Fixes insert module failure as free_irq() was not
done in previous rmmod.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:33 -08:00
David Brownell
37daa925cf USB: musb_hdrc: another davinci buildfix (otg related)
The DaVinci code had an implementation of the OTG transceiver glue
too; make it use the new-standard one.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:32 -08:00
David Brownell
10b4eadef1 USB: musb davinci buildfix
Trying once more to get this merged.  The original was submitted
for 2.6.27-rc2 or so, and never got correctly merged.  Neither
were any of the numerous subsequent resends.  Sigh.

  CC      drivers/usb/musb/davinci.o
drivers/usb/musb/davinci.c:35:32: error: mach/arch/hardware.h: No such file or directory
drivers/usb/musb/davinci.c:36:30: error: mach/arch/memory.h: No such file or directory
drivers/usb/musb/davinci.c:37:28: error: mach/arch/gpio.h: No such file or directory
drivers/usb/musb/davinci.c:373: error: redefinition of 'musb_platform_set_mode'
drivers/usb/musb/davinci.c:368: error: previous definition of 'musb_platform_set_mode' was here

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-27 16:15:32 -08:00
Bryan Wu
e22b582e91 USB: musb: Kill some compiling warning in musb Blackfin part
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:08 -08:00
Bryan Wu
7833414d4f USB: musb: Blackfin provides read/write I/O accessor in header files
Don't redefine the functions in musb driver

Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:08 -08:00
Bryan Wu
085ad4067b USB: musb: add Blackfin Kconfig options and Makefile
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:08 -08:00
Bryan Wu
c6cf8b003e USB: musb: add Blackfin specific configuration to MUSB
Some config registers are not avaiable in Blackfin, we have to comment them out.

v1-v2:
 - remove Blackfin specific header file
 - add Blackfin register version to musb_regs.h header file

Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:07 -08:00
Bryan Wu
6995eb68aa USB: musb: enable low level DMA operation for Blackfin
- DMA registers in Blackfin have different layout
- DMA interrupt flags need to be cleared by software

Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:07 -08:00
Bryan Wu
2c557a4a98 USB: musb: add Blackfin version low level register accessing helper functions
add Blackfin version low level register accessing helper functions

Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:07 -08:00
Robin Getz
d426e60dbf USB: musb: Make sure we program the correct values in only when necessary.
Make sure we program the correct values in only when necessary.

Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:07 -08:00
Bryan Wu
0c6a881844 USB: musb: add Blackfin driver to MUSB framework (v2)
- replace MUSB_FIFOSIZE register to MUSB_TXCOUNT, cause no MUSB_FIFOSIZE
   register on Blackfin
- use #ifdef to replace #if defined()

Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:07 -08:00
Felipe Balbi
c48a515525 USB: musb: check if set_irq_wake succeded and remember it
Without it, in platforms that don't provide irq_chip.set_wake(),
like omap, musb will WARN() on driver removal.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:01 -08:00
David Brownell
bb1c9ef1b4 USB: musb: host side diagnostics tweaks
Random host-side MUSB updates, mostly relating to better diagnostics:

 + Improve diagnostics on host side:
    - tx flush fifo:
       * Avoid hundreds of duplicate TX FIFONOTEMPTY messages
       * make "Can't flush TX fifo" a warning, and say which endpoint
    - giveback:
       * use correct status code
       * show completion function name not just URB pointer
    - Fix annoying "1 bytes" (should be "1 byte")

 + Be more consistent about failing init of unusable fifo_mode

It's not clear why that "can't flush TX fifo" message appears, though
it might relate to disconnection; I see it not infrequently

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 09:59:59 -08:00
David Brownell
71783e0def USB: musb: minor locking fix
Minor locking fix for musb_hdrc on OMAP3 and OMAP2430:
don't read DEVCTL without holding the spinlock, since
an IRQ could come in and corrupt things.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 09:59:59 -08:00
Kevin Hilman
58e660266d USB: musb: build fixes for DaVinci
- update includes after asm/arch --> mach headers move
- adds musb_platform_set_mode() stub

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 09:59:58 -08:00
David Brownell
96a274d1da USB: musb: sysfs mode updates
Fix three omissions in the "mode" sysfs attribute support:
  (a) inability to report errors;
  (b) no DaVinci support ... just report an error;
  (c) for omap2430, accepting unsupportable values

The 2430 stuff is still odd....

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 09:59:58 -08:00
Kay Sievers
427c4f3334 usb: struct device - replace bus_id with dev_name(), dev_set_name()
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 09:59:52 -08:00
Felipe Balbi
aa5cbbecd9 usb: musb: fix bug in musb_schedule
This bug was introduced recently. Fix it before bigger
problems appear.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-11-19 22:01:34 -08:00
Ajay Kumar Gupta
23d15e070c usb: musb: fix BULK request on different available endpoints
Fixes co-working issue of usb serial device with usb/net devices while
oter endpoints are free and can be used.This patch implements the policy
that if endpoint resources are available then different BULK request goes
to different endpoint otherwise they are multiplexed to one reserved
endpoint as currently done.

Switch statement case is reordered in musb_giveback() to take care of
bulk request both in multiplex scenario and otherwise.

NAK limit scheme has to be added for multiplexed BULK request scenario
to avoid endpoint starvation due to usb/net devices.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-11-13 14:45:01 -08:00
Felipe Balbi
b60c72abdb usb: musb: fix debug global variable name
In order to avoid namespace conflicts, add a prefix
to our kernel-wise symbol.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-11-13 14:45:01 -08:00
Ajay Kumar Gupta
eef767b761 usb: musb: Removes compilation warning in gadget mode
Fixes compilation warning when musb is configured in gadget mode.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-11-13 14:45:01 -08:00
Felipe Balbi
14a2c96f72 usb: musb: tusb6010: kill compile warning
Add an errno to failing case.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-11-13 14:45:01 -08:00
Ajay Kumar Gupta
f82a689fae usb: musb: Fix for isochronous IN transfer
Fixes blurred capture images in dma mode. Isochronous error field in
urb and source data buffer pointer were not updated properly in dma
mode.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-11-13 14:45:00 -08:00
Felipe Balbi
28c2c51c07 usb: musb: remove dead code from procfs
When removing the procfs file, I forgot to remove some
code that created and removed that file. Here's a patch
to fix it. Ideally this patch will be melded into the patch
removing the procfs file, don't know if it's possible still.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-17 14:40:59 -07:00
Felipe Balbi
458e6a511f usb: musb: general cleanup to musbhsdma.c
Basically getting rid of CaMeLcAsE, but also adding
missing lines and spaces.

Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-17 14:40:59 -07:00
David Brownell
c767c1c6f1 usb: musb_hdrc build fixes
Minor musb_hdrc updates:

  - so it'll build on DaVinci, given relevant platform updates;
      * remove support for an un-shipped OTG prototype
      * rely on gpiolib framework conversion for the I2C GPIOs
      * the <asm/arch/hdrc_cnf.h> mechanism has been removed

  - catch comments up to the recent removal of the per-SOC header
    with the silicon configuration data;

  - and remove two inappropriate "inline" declarations which
    just bloat host side code.

There are still some more <asm/arch/XYZ.h> ==> <mach/XYZ.h>
changes needed in this driver, catching up to the relocation
of most of the include/asm-arm/arch-* contents.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: stable <stable@kernel.org> [2.6.27]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-17 14:40:59 -07:00
Bryan Wu
64ca44a65a usb: musb: do not mess up count number and CSR0 register value
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-17 14:40:59 -07:00
Ajay Kumar Gupta
2492e6747f OMAP:MUSB: Corrects urb unlink function path
Fixes kernel panic while ISO IN transfer is aborted.Replaced
usb_hcd_unlink_urb_from_ep() from musb_giveback() to __musb_giveback()
to make sure urb is unlinked before giveback when __musb_giveback() is
called from musb_urb_dequeue().

Acquired musb->lock() before usb_hcd_unlink_urb_from_ep() within in
enqueue path.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-17 14:40:58 -07:00
Ajay Kumar Gupta
ae5ad29639 OMAP:MUSB: Fixes the TT programming.
Fixes enumeration failures when a USB device attached to a LS hub is
connected to OMAP EVM via HS hub. This is fixed by correctly
programming hub address register in enqueue path.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-17 14:40:58 -07:00